Allwinner sunxi

Hi, I'm trying to install my laser printer Brother HL 2130 in Armbian Jessie. The thing is, that in my older Armbian Wheezy system with same board and printer it works. Anyone has a clue? Maruprez

Maybe this is a faq. After installing and upgrading armbian to 5.23 on A10-Lime, if I leave serial console attached and Ethernet Cable attached, booting process hangs at: Uncompressing Linux... done, booting the kernel. while if I'm using serial console alone or Ethernet Cable alone, the booting process is fine. Why ?

Hello everyone and thank you for wonderful work on Armbian. i was wondering if anyone has any experiences to share on booting orange pi pc over network, i know it's possible to do this using Raspberry pi, but what's the latest status on Orange PI PC? is there a u-boot build capable of doing so? is this even possible?

Greetings, all! I've got a LeMaker A20 BananaPro, on which I'm using the Armbian mainline distribution (for a more complete description of my setup, please see below). I'm using a serial console to the board; I'm not connecting anything to HDMI for display. I'm running the distribution off of a brand new 8Gig SanDisk Extreme Pro. I would like to use alsa (at least in part) in the audio stack. I'm experiencing the following: When I have no audio playing through the audio out jack, I get a loud (powerline, probably) hum on my speakers. When I start audio playback (a wav through aplay, or an mp3 through mpd, etc.) the hum disappears, and the so…

Hello We are using NanoPi M1 board for robot application.So I am trying to install Ubuntu 16.04 LTS. I want installation procedure for Ubutu. In nanoPi M1 manual they mentioned only for Windows OS. If anyone knows procedure please help me.

Hi all Im just got to play with orangepi plus 2e with armbian. but i encounter allow of system hang after few hrs of usage. anyone encounter this? Current Arambian verison- OS: Ubuntu 16.04.3 LTS Kernel: 3.4113-sun8i Frimware: #8 Boot and storage: EMMC Desktop: Yes service/application install- Gparted Octoprint MJPG-Streamer thanks alot

Hi. I'm using Cubietruck, and installed Ubuntu server(mainline) on it. Suddenly, I can't write to disk(SD card). Actually, yes I can. I could create, edit, or even delete files, but all the changes are gone after the Cubietruck is rebooted. The deleted files are back, and created files are gone. What should I check? My SD card is Samsung Evo 16GB, and I'm running Cubietruck for more than 2 years. I have never encountered this weird situation.

Hello, I installed the Ubuntu desktop image from: https://www.armbian.com/orange-pi-pc/ to the SD Card with: sudo dd bs=4M if=Armbian_5.38_Orangepipc_Ubuntu_xenial_default_3.4.113_desktop.img of=/dev/sdb conv=fsync The orange pi does not boot, it took some time and the red LED is flashing on the top side and the screen is black. Maybe I did something wrong? Regards, caro

How to run a python script at startup on orange pi zero? Thx!

Hi all, as in title, gpio not work on latest Lime2 5.59 built from source using mainline 4.14.70 kernel and debian stretch. I can export correctly the gpios in sysfs but i cant get the right value. They always remain the same value. I've tried both pulled up and internal pulled up (active low) gpios with the same result. Also gpio buttons defined in dtc do not work. Any idea?

Hi, I am running a OrangePi One with Linux orangepione 3.4.113-sun8i #18 SMP PREEMPT Wed Jan 24 22:10:49 CET 2018 armv7l armv7l armv7l GNU/Linux DISTRIB_ID=Ubuntu DISTRIB_RELEASE=16.04 DISTRIB_CODENAME=xenial DISTRIB_DESCRIPTION="Ubuntu 16.04.3 LTS" And it seems that when I start the system without the hdmi cable and plug it afterwards, the HDMI is not handle correctly and my TV stays with a red screen. There is some way to configure the hdmi hot plug in this OS? I found that raspiberry pi has this option. (https://www.raspberrypi.org/documentation/configuration/config-txt/video.md)

I'm not sure if I should pursue this here or if I should open a ticket through Debian Bugs. A recent update now causes mpd to segfault. mpd comes from the Debain armhf repository. I'm not sure how to determine if this is a hardware issue with my board somehow or if there is an interaction with a new kernel or if it's because the package updated the binary or a library. To make sure it wasn't something weird in my configuration I moved the conf file out of the way and re-ran mpd with the same result. If it helps, I can post an strace output of the issue. James

I have updated the armbian kernel from version 20.11.3 to version 20.11.6 and eth0 only works by forcing the switch to 100FD. If I leave it on automatic, the port negotiates at 1000FD but loses most packets. Any suggestion?

Currently I receive rustc crashes after memory usage get to 3GB (1GB RAM + 2GB SWAP) when building firefox. After looking around why, I found that kernel isn't build with lpae extension. Although H3 soc supports lpae (Large Physical Address Extension), but kernel has CONFIG_ARM_LPAE flag not set and so we can't use more than 3GB of memory (1GB is reserved for kernel). (Processors that implement the ARMv7-A Large Physical Address Extension (LPAE), expand the range of accessible physical addresses from 4GB (232 bytes) to 1024GB (240 bytes) a terabyte, by translating 32-bit virtual memory addresses into 40-bit physical memory addresses.) After looking a…

Hi there, I've been "playing" around various debian images for my lime2 and http://www.igorpecovnik.com/2014/11/18/olimex-lime-debian-sd-image/ seems to be the most achieved so far. Stable and everything. The only thing I miss is the "change_display.sh" tool so that I can easily configure my board to switch between the Olimex LCD and the HDMI screen. Would it be possible to add these tools in the next image ? I understand that it requires sunxi-tools and a few other things but it looks a bit complicated for me. Thanks for the feedback. Maxime

I've been struggling for a while to get raspberry pi HAT type LCD to working. I've been working with loboris images before until recently that I've heard that armbian has cooked a new image for orangepi with newer kernel. In the description of images it is clearly indicated that the image works with small screen lcds which it seems to be true because there is no error when I want to load a notro module and it successfully loads. I've put lcd configurations in /etc/modules but I was not successful. this is the parameters I use in /etc/modules fbtft_device name=flexfb gpios=dc:22,reset:27 speed=48000000 flexfb width=320 height=240 buswidth=8 init=-1,0xCB,0x39,0x2C,0x00…

My Cubie crashed after 3-4 weeks and I installed Watchdog using the file change method. During my tests it works fine several times. But again after 3-4 weeks my Cubie was totally unavailable via SSH & console. Title: Armbian 4.81 Cubietruck Debian jessie dev (unofficial) Kernel: Linux 2016.01-rc3 Build date: 28.12.2015 Filesystem Size Used Avail Use% Mounted on /dev/root 917G 4.3G 867G 1% / devtmpfs 944M 0 944M 0% /dev tmpfs 944M 0 944M 0% /dev/shm tmpfs 944M 17M 927M 2% /run tmpfs 5.0M 4.0K 5.0M 1% /run/lock tmpfs 944M 0 944M 0%…

I am having troubles with getting audio from the sunxi audiocodec on my NanoPi NEO. I enabled audio in the .fex file and the configuration is as follows: [audio0] audio_used = 1 lineout_vol = 31 cap_vol = 5 audio_hp_ldo = "none" adcagc_used = 0 adcdrc_used = 0 dacdrc_used = 0 adchpf_used = 0 dachpf_used = 0 audio_pa_ctrl = port:PA16<1><default><default><0> When I ssh into the machine the codec does come up root@nanopineo:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: audiocodec [audiocodec], device 0: SUNXI-CODEC sndcodec-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: sndhdmi [sndhdmi], device 0: SUNXI-HDMIAUD…

Hi All, Sorry if this has been asked before, I haven't been able to find the answer yet. I wish to configure my OrangePi's (Lite and PC+) such that they power on automatically whenever the power is restored after a power outage without needing to press the power button. I'm not sure where we could configure this as the OrangePi's don't seem to have a bios like a Desktop PC. Dave.

Hello everybody, I am running 3.4.113 on my Orange Pi Zero like a charme. Now I was trying to install aircrack-ng-1.2-rc4. I am getting the following error: So I checked on the missing libnl: So for me it looks ok, does anybody have any idea how to fix the error? Thanks for some help

Hi there, when I run command "sudo shutdown -r now" (or sudo reboot) my orange pi shuts down instead of reboot. Why this happens and how to correct it please? Thank you. My armbian: Linux orangepilite 3.4.113-sun8i #10 SMP PREEMPT Tue Jan 24 02:57:18 CET 2017 armv7l GNU/Linux

Installed tightvncserver and sudo apt-get install xfonts-base. When I try to connect and see the "foto". How can I fix this?

Hello, to all OrangePI PC enthusiasts. Well I'm in the community of those who definitely underestimated the Orange of the PI, but let me share my burden :-) for the fun of it. It started with the camera- gc2035 and vfe_v4l2 modules. Had to try a couple of images until I got it by luck I guess - after that I found out that every image I use is not capable of having a FTDI device connected to "ANY" USB Port (OK, you got me, I didn't try the microUSB and I won't). After that I tried no matter what I wanted to connect to USB it was not even recognized. Now I'm back in changing/swapping around Images until I found one that let me plug anything I …

Hello, I have a cubieboard 2 (the one with only one SD slot) and there is a version of Linaro that is bootable in the NAND memory. I created a card with Debian Jessie Server (the last one) and boot it successfully, but when I run nand-sata-install I get a "No targets available. Please check your drives" pop up. I tried downloading the Debian Wheezy and creating a card and on that one I can see the nand memory blocks, but don't have the script to install and the one that came by default only installs to SATA (not to NAND). Anything I may be doing wrong here??

Hi all, I'm new to this forum, but I frequent the LinusTechTips forum a lot, some of you may recognize it. Any way, my issue is with my Orange Pi R1. I've tried both Ubuntu Server and Debian server images and I can't seem to get either to work. I'm using a good OEM Samsung wall wart that can supply up to 2 amps, and I'm using a 32GB Sandisk microSD I pulled from a working Raspberry Pi 2. With the Ubuntu Server image I can get in on the first boot and make a new user, but once it reboots to expand the filesystem it seems like it'm outta luck. I assume the red LED flashes when the kernel is running as normal, and after the first reboot the red LED never flashes, I can'…

I've tried to install GitLab onto Banana PI running Armbian (Ubuntu 16.04 server). I've followed the instructions for Raspberry PI (on https://docs.gitlab.com/omnibus/manual_install.html) and generic https://about.gitlab.com/installation/#ubuntu Unfortunately this fails: $curl -s https://packages.gitlab.com/install/repositories/gitlab/raspberry-pi2/script.deb.sh | sudo bash ... $ sudo EXTERNAL_URL="http://myurl.com" apt-get install gitlab ... Verifying we have all required libraries... Could not find gem 'devise-two-factor (~> 2.0.0)' in any of the gem sources listed in your Gemfile or available on this machine. Did anybody tried the same? Is t…

HI! Im new to Orange Pi Zero. I want to connect a speaker to my Orange Pi Zero. I went through some websites and forums, there saying that use pin 7 and 8 to speaker. I connected pin 7 to + and pin 8 to -. Then I entered 'speaker-test'. But it doesn't get any sound. root@orangepizero:~# speaker-test speaker-test 1.1.3 Playback device is default Stream parameters are 48000Hz, S16_LE, 1 channels Using 16 octaves of pink noise Rate set to 48000Hz (requested 48000Hz) Buffer size range from 256 to 262144 Period size range from 128 to 32768 Using max buffer size 262144 Periods = 4 was set period_size = 32768 was set buffer_size = 262144 0 - Front Left Time per period = 2…

Hi, i try config NanoPi M1 Plus to CVBS output. What i did: 1. Install legacy image from armbian 5.59 (kernel 3.4.y) 2. Used armbian-config to edit boot script: [disp_init] disp_mode = 1 screen1_output_type = 2 screen1_output_mode = 11 [tv_para] tv_used = 1 3. Added module tv into /etc/modules: #w1-sunxi #w1-gpio #w1-therm #sunxi-cir hci_uart rfcomm hidp dhd tv So far, i got only black screen on TV (no video, no audio). When i had config disp_out to HDMI, it worked fine. What i need config to enable TV out? Why it not working? Can anybody help me? Seems, i haven`t tv module... modinfo tv return modinfo: ERROR: M…

i just upgrade from jessie to armbian stretch (5.65) i check aplay -l, why only shows audio codec? anybody help? root@bananapim2plus:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Codec [H3 Audio Codec], device 0: CDC PCM Codec-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0

Hello Guys. เว็บพนันบอลต่างประเทศ เว็บแทงบอลต่างประเทศ HowTo: Setting up resolution 1600x900 & 1366x768 ? &how can i set up other resolutions those are not in h3disp like 1600x900 board is orangepi-pc

I am trying to enable memory split on my board. I am using Armbian Stretch with mainline based kernel 4.19.y. No matter what I do, after reboot I get: root@bananapi:~# free -h total used free shared buff/cache available Mem: 996M 170M 613M 4.8M 212M 799M Swap: 498M 0B 498M I've already tried adding to armbianEnv.txt: disp_mem_reserves=on extraargs=cma=96M After first boot I've already relinked /boot/script.bin to /boot/bin/bananapim1plus.bin and added fdtfile=sun7i-a20-bananapi-m1-plus.dtb to /boot/armbianEnv.txt in order to ha…

Hello Today my system was suspended after 5 times hit power button OPI was turn oFF After turn on, can`t connect to Network by eth0 or any WI FI. I have no idea whats happen I swap the wire but Led on eth connector in OPI yellow/green is blinking. Restart router and is the same What I should do?

Hello, I try to re-install my olimex lime 1, but I'm unable to boot from the current buster image. For now, here's what I do to flash the sd card: % wget -c "https://dl.armbian.com/lime/Buster_current" % mv Buster_current Armbian_20.02.1_Lime_buster_current_5.4.20.7z % 7z x Armbian_20.02.1_Lime_buster_current_5.4.20.7z % sudo sh -c "dd if=Armbian_20.02.1_Lime_buster_current_5.4.20.img of=/dev/sdc bs=1M" And I come up with a result like this: % sudo sfdisk -d /dev/sdc label: dos label-id: 0xd9b237ef device: /dev/sdc unit: sectors /dev/sdc1 : start= 8192, size= 2318336, type=83 Is this empty space before the first par…

Hello. I can't enable HDMI output for A64 on Orangepiwin platform - every time screen is blank (monitor not active). Monitor connected over hdmi to vga adapter. After linux kernel is loaded - monitor is alived. I try some options in boot.scr withnout effect for u-boot: video-mode=sunxi:1024x768-24@60,monitor=dvi,hpd=0,edid=1 video-mode=sunxi:1024x768-24@60,monitor=dvi,hpd=1,edid=1 video-mode=sunxi:1024x768-24@60,monitor=dvi,hpd=0,edid=0 and setenv console=tty0 hdmi.audio=EDID:0 disp.screen0_output_mode=EDID:1024x768p60 Need help.

Hello there. I have problems with connecting device with 1-wire protocol. Device: DHT11 Temperature-Humidity Sensor - It is Arduino version with pullup on the board. Board: Orange Pi Zero LTS (H2+) System: Linux orangepizero 5.10.21-sunxi #21.02.3 SMP Mon Mar 8 00:28:04 UTC 2021 armv7l armv7l armv7l GNU/Linux Based on instructions im preformed some steps: 1) Through armbian-config im enabled w1-gpio 2) Installed gpio app to get info about ports: +-----+-----+----------+------+--Orange Pi Zero--+------+----------+-----+-----+ | H2+ | wPi | Name | Mode | V | Physical | V | Mode | Name | wPi | H2+ | +-----+-----+------…

/sys/class/leds is not populated when running jammy with kernel 5.16.11

Hello, I am looking for the latest Banana Pi M1 server image but I only see the XFCE desktop version. Witch image should I use?

Using the latest FW Image https://redirect.armbian.com/orangepizero2/Bullseye_legacy the Orange Pi doesn't boot anymore or at least I'm not able to establish a ssh connection. If I use the the archived previous version the board behaves completely normal until I perform an "apt upgrade". After upgrading it also doesn't boot anymore.

Hey, I recently decided to give the 22.11 a try on my M1, but I can't get my sata SSD to be the system root and boot again. 18.04 it worked for me with the exact same setup. I used this: https://docs.armbian.com/User-Guide_Getting-Started/#how-to-install-to-emmc-nand-sata-nvme-usb went with armbian-install only option for me was boot from SD and system on sata. But after the preparation of the ssd, the reboot always runs into emergency mode with not really good hints how to solve, or what even the issue is. Any tips or hints are welcomed.

[root@lalaki ~]# journalctl -p4 Sep 16 14:27:11 lalaki kernel: watchdog: watchdog0: watchdog did not stop! Sep 16 14:26:51 lalaki kernel: cacheinfo: Unable to detect cache hierarchy for CPU 0 Sep 16 14:26:51 lalaki kernel: cacheinfo: Unable to detect cache hierarchy for CPU 1 Sep 16 14:26:51 lalaki kernel: cacheinfo: Unable to detect cache hierarchy for CPU 2 Sep 16 14:26:51 lalaki kernel: cacheinfo: Unable to detect cache hierarchy for CPU 3 Sep 16 14:26:51 lalaki kernel: KASLR disabled due to lack of seed Sep 16 14:26:51 lalaki kernel: cacheinfo: Unable to detect cache hierarchy for CPU 0 Sep 16 14:26:51 lalaki kernel: axp20x-regulator axp20x-regulator: DCDC frequency o…

Imagewriter does not work in Win7 does not see drives. I have a Orange Pi One and using the link on this site I have downloaded Armbian. However although Suse imagewriter starts it does not see any drives to write to on my laptop and not the sdcard either. I can select Armbian but clicking copy just brings up a error. I downloaded Rufus but all that will do is format the sdcard. There is a raw file and a asc file for Armbian how do I create a sdcard to boot my Orange Pi One? using windows 7.

Hello, I am new to this forum and I would like to ask a question concerning Allwinner's H3 eFuse feature. Studying the chip's datasheet, I saw that there is this eFuse feature, which would be mightily handy for my to-come project using H3 or H2+ hardware (OPi Zero to be specific) as a basis in combination with Armbian (which I find fantastic btw). Is there any driver available for this feature? I couldn't find any info on the net so far. Thx a lot for your time and efforts. BR, andormaybe

Starting kernel ... <6>Booting Linux on physical CPU 0 <6>Initializing cgroup subsys cpuset <6>Initializing cgroup subsys cpu <5>Linux version 3.4.113-sun7i (root@vultr.guest) (gcc version 4.8.4 (Ubuntu/Linaro 4.8.4-2ubuntu1~14.04.1) ) #1 SMP PREEMPT Tue Jan 24 12:18:02 UTC 2017 CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: sun7i <6>Memory Reserved: <6> SYS : 0x43000000 - 0x4300ffff ( 64 kB) <6> LCD : 0x44000000 - 0x44ffffff ( 16 MB) Memory policy: ECC disabled, Data cache writealloc <6&gt…

Hi there, I am new to OrangePi and Linux as well and that's probably why I have faced my first problem I could not find an answer on web. I use OP Lite with the latest debian jessie. And there is the problem (or just a bug): after some time of using WiFi (and wwan) I wanted to disable it in order to reduce "excessive" power consumption. So firstly I had disabled it via "nmcli" and after a while I found out about "h3consumption" command. But recently I wanted to install (and download) but none of the above commands were able to re-enable them. Any ideas how to re-enable (besides loading new OS image) ? In addition, I noted that changind "h3consumption" is not a…

Hi Armbians, I'm running two identical Cubietrucks with Armbian Jessie systems in headless (very lean) mode without any X-Windows or the like. Both boot from 16GB SD-Cards. Now one of them, which had encountered a number of power failures, suddenly ran out of space on the SD-Card (100% usage of / ), while the other CT only shows 22%. I ran across this phenomenon, when the system failed to carry out an apt-get update at one point and important services Samba were no longer started. I then searched the root filesystem for culprits but there was nothing suspicious ... So I thought there might be a partial "destruction" of the fil…

I'm running a dockerized VDR server on the BPi, still on bananian. Every time I installed armbian, I had to discover that video playback on remote devices started to stutter. Without knowing about the details, my guess is that this is owed to the fact that the mainline kernel build does not feature hw video decoding. (Though I'm not sure whether bananian had it actually.) Unfortunately I cannot use the legacy kernel build, as docker is not supported on that platform. Is there any chance to kind of enable hw video acceleration on the mainline build? I saw some posts here and there in the forum on that topic, but none seemed really having solved it d…

Hi: I want to add "nowayout" watch dog parameter to my orange pi pc. I think the syntax should be "sunxi_wdt.nowayout=1". but I don't know how to add this to kernel boot parameter in armbian? is there a config file to add boot parameter? BTW I found if I shut down my orange pi PC normally, I can not restart it unless I unplug/plug the power cord. is this behavior expected? thanks a lot for help!!

Hi, Got Debian (8) legacy 3.4.113 server/console and would like to setup a WiFi hotspot. (latest Armbian build 5.51) Seen two methods in Armbian docs 1. -> https://docs.armbian.com/User-Guide_Advanced-Features/#how-to-set-wireless-access-point and via armbian_config in https://docs.armbian.com/User-Guide_Armbian-Config/ 2. -> https://www.youtube.com/watch?v=__BJtInOQFY So I'm a bit buffled about it. Got some questions Got a RTL8188CUS is it suported nowadays? or should I get a specific other one? Do I need to have internet/ethernet/lan connection active during the hotspot creation via armbian_c…

it seems that the kernel-header version is not updated to the actual kernel version: $ uname -a Linux cubietruck 4.14.65-sunxi #11 SMP Tue Aug 21 10:02:12 CEST 2018 armv7l GNU/Linux install header using armbian-config tool doesn't work - no error message thereafter: installed header manually: linux-headers-next-sunxi dpkg: warning: version '4.14.18-sunxi 4.14.65' has bad syntax: invalid character in revision number Building for 4.14.65-sunxi Module build for kernel 4.14.65-sunxi was skipped since the kernel headers for this kernel does not seem to be installed.

i'm using banana-pi-m2+ already enable i2s0 by changing dtb file in /boot/dtb and can see i2s module load but aplay -l still not showing anybody help? root@bananapim2plus:~# lsmod Module Size Used by snd_soc_hdmi_codec 16384 0 dw_hdmi_i2s_audio 16384 0 sun8i_dw_hdmi 16384 0 dw_hdmi 28672 2 dw_hdmi_i2s_audio,sun8i_dw_hdmi cec 40960 2 dw_hdmi_cec,dw_hdmi sun8i_codec_analog 24576 1 sun4i_codec 32768 3 sun4i_i2s 16384 0 snd_soc_core 118784 4 sun4i_codec,sun4i_i2s,sun8i_codec_analog,snd_soc_hdmi_codec snd_pcm_dmae…

Hello, No bluetooth device in my Armbian... Banana Pi M2+ ARMBIAN 5.65 stable Ubuntu 18.04.1 LTS 4.14.84-sunxi dpkg-query -Wf '${Version}\n' bluez 5.48-0ubuntu3.1 No Bluetooth device(hci0): rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Which refers to the error: systemctl status ap6212-bluetooth.service ● ap6212-bluetooth.service - LSB: Patch firmware for ap6212 adapter Loaded: loaded (/etc/init.d/ap6212-bluetooth; generated) Active: failed (Result: exit-code) since Tue 2019-01-08 09:18:38 UTC; 1min 2s ago Docs: man:systemd-sysv-ge…

Hi, I am using Linux nanopiair 3.4.113-sun8i distribution on my Nano Pi Neo Air and trying to get the g_ether works. After using modprobe g_ether and set up the network/interfaces auto usb0 iface usb0 inet static address 192.168.0.2 netmask 255.255.255.0 then edit /etc/modprobe.d/g_ether.conf: options g_ether host_addr= 06:7b:95:4c:59:d7 After reboot it shows: [ 6.868451] usb0: MAC 06:7b:95:4c:59:d7 [ 6.868475] usb0: HOST MAC 5e:5b:65:8f:94:85 [ 11.484526] systemd[1]: Found device /sys/subsystem/net/devices/usb0. [ 16.249726] ADDRCONF(NETDEV_UP): usb0: link is…

Hi, as a newbie in this forum, I see a lot about HW, but almost nothing about OS Versions? Puzzled, where to place, I try to do this here: After installing Debian Buster & XFCE on an OPI-Zero, I'm getting frquently installation errors. Its always dpkg: unrecoverable fatal error, aborting: files list file for package 'xfce4-timer-plugin' is missing final newline E: Sub-process /usr/bin/dpkg returned an error code (2) like this one: ┌────────────────────────────────────────────────────────────────────┐ │ • MobaXterm 9.4 • │ │ (SSH client, X-…

Hello! Here's the outputs: $ uname -a Linux opi3 5.4.28-sunxi64 #20.02.7 SMP Sat Mar 28 17:25:10 CET 2020 aarch64 GNU/Linux $ sudo aplay -l **** List of PLAYBACK Hardware Devices **** card 0: allwinnerhdmi [allwinner-hdmi], device 0: 5091000.i2s-i2s-hifi i2s-hifi-0 [5091000.i2s-i2s-hifi i2s-hifi-0] Subdevices: 1/1 Subdevice #0: subdevice #0 ...and that's all! There's no second card. I tested HDMI sound with my TV -- works fine, sound plays. But I need to use 3.5mm jack. Is it physically damaged? Or what could I do? Help, please!

Hello, after a poweroff command, the board Led switches off but the ethernet port Led still green blinks. The os has well performed the shutdown (I can see this through the UART). How is it possible? Thanks

I just installed the image located here and am unable to get a bluetooth keyboard and mouse to connect. https://www.armbian.com/orange-pi-zero-plus-2-h3/ And used armbian-config -> Network -> Enable bluetooth. Here's the output of some common debugging commands I found in the forums. root@orangepizeroplus2-h3:~# lsusb Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 001: ID 1d6b:0001 Linux Foundation…

Dear community, Im searching the device-tree overlay files for Banana Pi M2 Berry/ Ultra in dts format. I found: sunxi-DT-overlays But that doesnt contain the sun8i-r40 overlays I want to see how the i2c0, i2c1 and w1-gpio overlay looks!" greetz, hexzhen3x7

Hello everybody, I have installed the banana pi image Bananapi_Ubuntu_2.8_trusty_3.19.7. Almost everything works fine but I am missing a usb driver: https://www.silabs.com/products/mcu/Pages/USBtoUARTBridgeVCPDrivers.aspx All my attempts of installing the driver failed: - when I try to use a ko-file from a different ubuntu version, I geht the error: "Exec format error" - when I try to compile the source from the link above, I get an "compiler too buggy" error - when I update the compiler and try to make the source, I get: make[2]: *** No rule to make target `arch/arm/tools/gen-mach-types', needed by `include/generated/mach-types.h'. Stop. make[1]: *** [arch…

Just noticed some ugly detail: 1.) the switch is active during boot, and it defaults to all ports on one VLAN. 2.) My laptop is quite agressive when it comes to DHCP, it's connected to one of the local ports of the BPI-R, so it detects immediatly that the ethernet connection goes down and up. 3.) So I end up with the cable modems external IP address on my laptop, and a BPI-R that is unreachable, ... Any idea how to turn off the network switch in the boot loader? TiA, Andreas

Hello, with the update to the new kernel (4.6.3-sunxi) I get some problems on my banana pro. First, while the system starts I get sometimes a kernel panic. In the most cases the kernel will boot on the second or third try. But the second one will be contantly and can't be avoided by a system reboot. The network interfaces don't be worked. The will be initialized during the system start process, get there IPv4 addresses from the router per DHCP and ifconfig shown them with the state "up". Everything looks ok. But if I try to connect another system, the connection will be failed. Any ping, as exsample to the router (default gateway), fails. The ping t…

Hi All, I seem to be encountering an issue with setting the MTU for the 8189fs driver on the 4.10.0-sun8i kernel I am trying to set the MTU for wlan0 to 1532. Note this works on the 3.4.113-sun8i kernel without issue. #uname -a Linux orangepipcplus-02c0008115dff7be 4.10.0-sun8i #10 SMP Sun Feb 12 16:51:59 AEST 2017 armv7l armv7l armv7l GNU/Linux /etc/network/interfaces ---------------------------------------------------------------------------------------------------------------------------------- auto wlan0 iface wlan0 inet6 manual wireless-channel 1 wireless-essid batnet6 wireless-mode ad-hoc wireless-ap 02:13:13:13:13:13 …

____ _ _ _ _ / ___| _| |__ (_) ___| |_ _ __ _ _ ___| | __ | | | | | | '_ \| |/ _ \ __| '__| | | |/ __| |/ / | |__| |_| | |_) | | __/ |_| | | |_| | (__| < \____\__,_|_.__/|_|\___|\__|_| \__,_|\___|_|\_\ Welcome to ARMBIAN 5.27 stable Debian GNU/Linux 8 (jessie) 3.4.113-sun7i System load: 0.92 Up time: 1 min Memory usage: 4 % of 984Mb IP: 192.168.1.77 CPU temp: 34°C Usage of /: 15% of 7.2G How can I change this logo?

Yesterday my 14" Pinebook arrived so I thought I'll collect some already available information. A lot of work still has to be done to get a decent laptop experience with this hardware so this is neither a review nor a stupid Un-Review but just a preview instead. To get the idea about dimensions I added a 13" and a 15" laptop to the picture. Pinebook is wedge-shaped and thickness matches both the 2011 15" MacBook Pro and the 13" from 2015: Display size closely matches the 13" MacBook Pro (but of course pixel density / resolution don't match as well as quality: TN vs. IPS and coating -- it should be obvious if you've the 'you get what you…

I have tried a few different suggestions that I have seen online to implement wifi on Orange PC with a wifi dongle. However, none them can work reliably. OrangePi zero works but wifi speed is very slow (about 1-2Mbps). I recently tried using Raspberry Pi with wifi dongles. It is almost plug and play and very reliable. I hope there is a way to do the same on OPi. If anybody know one, please let me know. I will be happy to try it out and report back.

Don't quite know what to expect here. The download page implies that there should be a gadget serial connection but there is nothing. I don't even see the USB DRC getting registered. Is this a known issue and is there a solution? TAIA. # nanopineo:~$ uname -a Linux nanopineo 4.11.3-sun8i #3 SMP Wed Jun 7 13:28:34 CEST 2017 armv7l armv7l armv7l GNU/Linux # nanopineo:~$ lsusb -t /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=ehci-platform/1p, 480M # nanopineo:~$ lsmod Module Size Used by evdev 20480 1 brcmfmac 172032 0 brcmutil …

Hi to everyone, I'm new at armbian forum, but following the project since some month. As far as I can tell all contributors make a great job to enable a stable debian based distribution to many as possible arm-based boards. Thanks a lot for this great job. I bought one of the first available Banana Pi M3-boards in Germany, because I wanted (and did it already very successfully) to set up a small server for email, music storage, mythtv-backend, read out my central heating.... Until now I use a stripped down image based on the provided Ubuntu 16.04 image from http://www.banana-pi.org/m3-download.html As you all know the "support" and further developmen…

DO NOT READ FURTHER I GOT IT COMPILED after typing "apt-get install htop" it started to install the headers.... strange ------------------------------------------------------------ Hey guys, I am stuck: Followed this: https://docs.armbian.com/User-Guide_Advanced-Features/#how-to-build-a-wireless-driver Try to port it to r8152.ko (RTL8153) / ax88179_178.ko I. (Before I started "apt-get update && upgrade") 1. Install Armbian Headers via armbian-config (Check) 2. wget http://www.asix.com.tw/FrootAttach/driver/AX88179_178A_LINUX_DRIVER_v1.18.0…

I've been using a Beelink X2 with Armbian for some time now booting from eMMC. I ran an "apt update; apt upgrade" on the box early on 01/14/2018 and a reboot was suggested at the end. The system did not successfully reboot after this update and it appears that it doesn't recognize uboot on the eMMC. At the time I had other pressing matters so I set it aside to work on today. Today I downloaded the latest image Armbian_5.34.171121_BeelinkX2_Debian_stretch_next_4.13.14_desktop.img, verified it and successfully wrote the image to a 16GB microSD card. This successfully booted the X2, I then did an "apt update; apt upgrade" on the microSD card and rebooted. This then …

H there, I am using OPi0 TV out. I know, there are hardcoded PAL and NTSC resolutions only. But I would like to ask, if there is any tutorial how to build it up with my own lower resolution e.g. 320x240? (i know I should recompile driver for it but any help where to start is appreciated) Many thanks.

I have been using this orangepi for several years now. Today SSH stopped working (it would hang indefinitely after password prompt) so I decided to restart it by removing and re-plugging the psu cable. After that it never appeared on the network again. 1) the board lights up: green / orange light on ethernet, and one green light on MB that turns on for ~25sec then turns off for ~10sec 2) I connected it to two switches with multiple cables, none of them show the ethernet port as active (no light on the switch port) Obviously due to 2) it doesn't appear on the router 3) microsd mounts fine on my pc, did a backup and flashed a clean image to no avail, wil…

Hello i found it on both my Opi PC+ and Opi Plus 2E , Both ARMBIAN 5.59.180918 nightly Debian GNU/Linux 9 (stretch) 4.14.70-sunxi. As i get some stability issues with Jeedom i'm playing with frequencies and governors and found that strange thing : root@orangepipcplus:~# cat /etc/default/cpufrequtils && cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_available_frequencies # WARNING: this file will be replaced on board support package (linux-root-...) upgrade ENABLE=true MIN_SPEED=408000 MAX_SPEED=1296000 GOVERNOR=ondemand 240000 480000 648000 816000 912000 960000 1008000 1104000 1200000 1296000 root@orangepipcplus:~# it seems there…

Hi, I am new here and searched the forums for an answer to my questions regarding the NanoPi NEO2 and NEO Plus2. Most answers I could find, but a few were left open. The NEO Plus2 is marked as WIP. Why? What do I have to expect not to work? Both boards are similarly old, from what I could find. Will the Plus2 move up to "supported" eventually or does it currently more look like the route is going towards CSC? Do common features like GPIO access, SPI, I2C ... work with current images? Do specific features where the Plus2 differs from the NEO2 like WiFi, Bluetooth, ... work? I already found out, that the second USB port should work…

I'm trying to recompile U-Boot to move the serial console on my OP Zero from uart0 to uart2. I didn't have any trouble to move the linux console, but I'm struggling with U-Boot. I tried creating a patch to change stdout-path in the device tree: https://github.com/u-boot/u-boot/blob/master/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts#L65 ff --git a/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts index d166ffc..0e2e48d 100644 --- a/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts +++ b/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts @@ -55,7 +55,7 @@ compatible = "xunlong,orangepi-zero", "allwinner,sun8i-h2-plus"; aliases { …

I wanna start out and say I have been using Armbian for a year and it's been great. Thank you. I have built many images over the year and have only noticed the issue recently. I have noticed in the bionic builds for OpiZ+ that some base level packages are missing. The one I noticed was netplan. This is the new standard for bionic. I have not compiled a complete list of missing packages at this time. I had built this image before around 5.0-5.1 kernel release without issue. Netplan was included. Current build at 5.3 RC does not include this package. I suspect that others may be removed. Are these packages missing intentionall…

Hello there, I tried to use on OPC3 bionic the ttyS1 for communcation with a serial device and didn't get it to work. ttyS3 works fine. Configuration is done for both. But now I need to communicate with a second and possibly a third serial device. So I hoped for updates. But now I can't find a download of the bionic version and i have to make decision how to go further on. Does it make sense to switch to buster or stretch? Is bionic only temporarily or finally offline? Whats the reason? Any idea when there is a chance to get a stable release. Possibly with 6 Months or surely not within 6 months. Which version is more likely to …

Hi there, I have been trying Armbian Buster for the first time. On the first look everything works fine and quick. But I cannot get proper sound from the soundcard. Instead there is only random noise. Interestingly the speaker-test works fine in stereo. $ uname -a Linux teres-a64 5.4.28-sunxi64 #20.02.7 SMP Sat Mar 28 17:25:10 CET 2020 aarch64 GNU/Linux $ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: sun50ia64audio [sun50i-a64-audio], device 0: 1c22c00.dai-sun8i sun8i-0 [1c22c00.dai-sun8i sun8i-0] Subdevices: 1/1 Subdevice #0: subdevice #0 $ speaker-test -twav -c2 -Dhw:0 speaker-test 1.1.8 Playback device is hw:0 S…

I'am using Cubieboard2. Todays morning i've got mistery "rcu: INFO: rcu_sched detected stalls on CPUs/tasks" with a complete failure of the entire network subsystem. How it was: Jul 13 09:12:36 hassio kernel: rcu: INFO: rcu_sched detected stalls on CPUs/tasks: Jul 13 09:12:37 hassio kernel: rcu: 1-...0: (21 ticks this GP) idle=a56/1/0x40000000 softirq=4946049/4946050 fqs=2286 Jul 13 09:12:37 hassio kernel: (detected by 0, t=5252 jiffies, g=11125849, q=117) Jul 13 09:12:37 hassio kernel: Sending NMI from CPU 0 to CPUs 1: Jul 13 09:13:13 hassio systemd[1]: systemd-udevd.service: Watchdog timeout (limit 3min)! Jul 13 09:13:13 hassio systemd[1]: syst…

Remark: on my Orange Pi PC and Orange Pi Plus 2e - everything is OK. Problem occurred on Orange Pi Plus 2 and Orange Pi Zero After upgrading to: [root@PKTEST ~]# uname -a Linux PKTEST 5.10.4-sunxi #20.11.6 SMP Sun Jan 3 21:28:45 CET 2021 armv7l GNU/Linux My "headless" Orange Pi Plus 2 "disappeared from network. I switch it off and connected via serial. I was able to login. Device runs successfully, it is assigning IP to network interface (static assignment) but... there is no connectivity at all (both egress and ingress). [root@PKTEST ~]# ifconfig enx0281cbcd0fcf: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 …

Hello, I am not able to get the keyboard working. I have tried the downloads and compiling my own images. Bulleye is the only thing I can get to compile. There are error massages if I try to compile anything other than Bulleye.

Pinecube fails to boot with Armbian_23.5.0-trunk.140_Pinecube_bookworm_edge_6.2.13.img . In the boot log is this line: So I tried to modify `fdt_addr_r` env variable and were able to succesfully boot with theese commands executed in u-boot console: So adding following line to /boot/armbianEnv.txt on sdcard can fix booting permanently: Complete boot log:

Armbian 6.6.16-sunxi64 (bookworm) on NanoPi NEO2 NanoHatOLED fails: - GPIO devices are missing; 2024-03-29 23:04:55 root@M-DNS:~# uname -a Linux M-DNS 6.6.16-current-sunxi64 #2 SMP Fri Feb 23 08:25:28 UTC 2024 aarch64 GNU/Linux Seems regression of earlier issue that had been solved: Would appreciate as GPIO will restored in kernel.

I suddenly have a need to test Linux 6.11 or greater, because there's a needed improvement in the panel-mipi-dbi-spi driver (thread keyword ili9488) User "The Going" has kindly advised me to try his Armbian branch with Linux 6.12, so I am here sharing results as I test it with my Orange Pi Zero 3. Initial instructions: https://forum.armbian.com/topic/35635-armbian-242-is-broken-on-orange-pi-pc2/#findComment-207980 At first try, I decided to NOT follow this step: armbian/build> egrep '^-' patch/kernel/archive/sunxi-6.12/series.conf (finds all the excluded patches) Well, I continued. Choosing Linux Edge, shallow o…

Hello, I have problems with the armbian distributions on my orange pi zero 3 because I can't even use chatgpt to activate the sound card on the expansion board that comes as an accessory for the orange pi zero 3. I'm referring to the board that has two USB outputs and an audio jack port that I think is also a video port, but I can't get sound out of that port, only sound comes out of the HDMI port. It's a real mystery since there's no problem with the other distributions, but with armbian I can't get that audio output port to work. If you can help me please, I've tried a number of things and I can't get it to work.

Hi, First of all, thank You for your work. On a project we are using Nanopi Neo Air boards with an Allwinner h3 processor and a 8GB eMMC flashed with an Armbian OS: $ uname -a Linux <DEVICE_HOSTNAME> 6.6.75-legacy-sunxi #1 SMP Sat Feb 1 17:37:57 UTC 2025 armv7l GNU/Linux $ lsb_release -a No LSB modules are available. Distributor ID: Debian Description: Debian GNU/Linux 11 (bullseye) Release: 11 Codename: bullseye Recently we have been getting increasing reports of the boards being stuck on boot, on message 'Starting Kernel ...' (checked from logs available on COM port). Although this behavior is highly undesira…

Hi, Looks like kernel config CONFIG_USB_STORAGE_DEBUG=y has been set in the Debian Jessie 4.0.4 build. That means, that when I have I/O to a usb-storage device, systemd-journald is consuming ~70-90% CPU time on consuming debug log lines from the kernel. Is this by purpose? How would I be able to filter or disable all this log content from the kernel to journald?

hi guys, im trying to compile media_build but it says the kernel has no i2c mux support how could i easy compile a new kernel with i2_mux enabled on the orange pi?

Hi! I love this Linux distribution, I have tried some months ago and had worked very well. Now, I want install armbian in a pdduino3b, I go to "downloads" select pcduino3, and I have two options: Xenial_server_vanilla and Xenial_server_legacy. I want hardware acceleration and most options of drivers and compatibility possible, so, I go for legacy option. But I realize that the two images have not a desktop environment, this is true? If yes, where can I download the full newer armbian version with legacy kernel and desktop ready? I try install xcfe over legacy image, but I have found for errors like "screen not found" and others... Regards.

First of all I've got an OPI PC and I'm newbie with armbian and Linux in general I've managed to read DS18B20 temperature sensor and now I want to read Temp and Humidity from a SHT75 sensor which has the same specifications as the SHT1X family of Sensirion sensors. I've installed WiringPi library and I've been searching on google how to make SHT75 work with little success Any documentation or examples to see?? Any help would be appreciated Thanks

Hi all. I have a Banana Pi M1+ and I want to use it as a NAS using a SATA HDD (1TB). I read this article http://linux-sunxi.org/Cpufreq#Performance.2Ffunctionality_impacts and I want to change the scaling_max_freq. I installed the "Armbian_5.20_Bananapi_Debian_jessie_4.7.3" image. But the maximum frequencies available is 960000. I tried to compile the kernel by myself, changing the file sources\linux-vanilla\v4.9.5\arch\arm\boot\dts\sun7i-a20.dtsi as suggested in other posts. cpu0: cpu@0 { compatible = "arm,cortex-a7"; device_type = "cpu"; reg = <0>; clocks = <&cpu>; clock-laten…

Hello! I'm using Wheezy under kernel 3.4.x on Lime2 with 7" LCD and i added fbcon=rotate:1 in boot.cmd and the console booted in portrait but LXDE is still in landscape. I also added FBDEV_ROTATE_CCW=90 but with no results. I can rotate the screen from the /usr/share/X11/xorg.conf.d/XX-fbturbo.conf file but every time i touch the screen the LXDE crashes. Any suggestions please how to rotate the screen in LXDE? Thank you!

Hi, I have been messing around with an Orange Pi One Board for a day or 2 now. So far the only distro that works has been yours. But I have the weirdest thing when I apply an update. Excuting apt-get update actually causes the machine to lose power completly. I have been looking at more data this is what I have. After and before the crash. Last freeze with htop analyzing. Am I missing something? I don't see a good reason for this to happen. Is there a common method to fix this if it is a known issue?

Hello, guys, please help setup HDMI output to 480x320 in mainline kernel for BananaPi M2. I am using 3.5inch HDMI display, it is working fine but my current resolution is too high. All attempts to change disp_mode in armbianEnv.txt didn't help. Thanks

Hello people, I'm using Armbian 5.30 - kernel 3.4.113 on a Nanopi NEO. and I'm relatively new to this stuff, so please bear with me. I successfully managed to install an LCD screen on SPI (ILI9341) using this command: sudo modprobe fbtft_device custom name=fb_ili9341 gpios=reset:1,dc:201,led:6 speed=16000000 rotate=90 bgr=1 So far so good, but the resolution of the screen is too little and can't load anything - for example Dosbox. I would want to replicate the trick that already exists on Raspberry/Raspbian, and that is to framebuffer a higher res screen (at least 640x480) on the tiny LCD's resolution of 320x240. This is the p…

I have encoutered some difficulties on carrier detection with network-manager on ethernet port, on lime2, on default kernel, 5.38. On mii-tools and ethtools, carrier is correctly reported. The result, network-manager try to activate connection at boot even cable is not plugged. It's report drivers (sunxi_gmac) does not support carrier detection, as i found in syslog When unplugged, the connection is still active. Apr 11 11:39:03 localhost NetworkManager[491]: <info> [1523439543.5279] NetworkManager (version 1.2.6) is starting... Apr 11 11:39:03 localhost NetworkManager[491]: <info> [1523439543.5321] Read config: /…

I have a problem with my Opi z+, it is assumed that its maximum frequency is 1200 Mhz, but it does not rise from 816 Mhz. I use a Raspberry charger, of 3000 mha. I changed the governor to performance but it does not go up to 816 Mhz. I use Armbian, based on ubuntu 18.04

Hello, I've purchased a 2e recently, in order to replace a RPI3 with a more powerful device (and get graphics acceleration, be able to watch youtube videos, etc). I've tested multiple builds, and even on the legacy kernel, there is just no way to get it to work properly. The board, when it sits completely idle, is between 48 and 52°. And if I move a window on the desktop, it's all laggy and the cpu jumps to 60+° --the same with a mainlain image in fact, in headless mode... frequently the console would freeze for a couple seconds while the temperature is very high for no reason. It seems there is no hardware graphics acceleration, ever. Curr…

Hi all, My Armbian hangs (freeze) after 1-2 hours. Below dmesg Aug 17 19:10:39 localhost kernel: [ 1666.194984] WARNING: CPU: 0 PID: 693 at lib/iov_iter.c:695 copy_page_to_iter+0x21d/0x35c Aug 17 19:10:39 localhost kernel: [ 1666.194987] Modules linked in: tun xt_nat xt_tcpudp iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_filter snd_soc_hdmi_codec rc_cec dw_hdmi_i2s_audio dw_hdmi_cec evdev sun8i_dw_hdmi dw_hdmi cec ir_lirc_codec lirc_dev pl2303 usbserial sun4i_i2s sunxi_cir sun8i_codec_analog sun4i_gpadc_iio sun4i_codec sun4i_tcon sun8i_mixer snd_soc_simple_card snd_soc_simple_card_utils snd_soc_core snd_pcm_dmaengine snd_pc…

I'm trying to figure out what happened in my device this morning. the process that i'm monitoring was interrupted and restarted and i'm want to know that reason, is it internal code reasone or system failure that caused to my process to crash. i'm attaching the /var/log/message piece of logs when my process crashed. can you tell me what happened? I'm using NanoPi2 NEO with latest armbian version for this specific board, Thanks alot Spoiler Feb 1 05:16:13 nanopi NetworkManager[642]: <info> [1548990973.1753] dhcp4 (eth0): address 10.0.0.5 Feb 1 05:16:13 nanopi NetworkManager[642]: <info> [1548990973.1822] dhcp4 (eth…

Im tring to access the GPIO using Python3 on a bananapi M1 Linux m5 4.19.38-sunxi #5.85 SMP Wed May 8 14:20:48 CEST 2019 armv7l GNU/Linux I manage to get access to gpio in shell, c, and in python2, but not in python3 with the following software: https://github.com/BPI-SINOVOIP/BPI-WiringPi https://github.com/BPI-SINOVOIP/BPI-WiringPi2-Python The error in python3 is the following (in pyhon2 work) : Traceback (most recent call last): File "/root/src/BPI-WiringPi2-Python/wiringpi2.py", line 18, in swig_import_helper fp, pathname, description = imp.find_module('_wiringpi2', [dirname(__file__)]) File "/usr/lib/python3.5/…

I'm trying to make a master image to install to some NanoPI Neo boards. I have everything running fine from micro SD card. I used armbian-config to flash from SD to the eMMC and it boot and works. Now I'm looking for a way to flash the eMMC from command line in an automatic fashion, after looking for other threads in the forum I found about command nand-sata-install but it has a GUI and no --help parameter, so I guess it is not the exact program I have to use. I tested using dd command to copy the disk, but since there is this u-boot thing I think it is not just a standard disk copy because it failed (maybe my problem). My final idea is to have a master SD …