Tinkerboard

I try to get working a tinkerboard on a battery. I can do that with S.USV or S.USV Mobile but i don't know the difference between them. I have a xl4015 (5Amp buck convecter) but I don't really understand how it's work (i have a lm2596 too). I have a 20AWG micro-usb too but i can power it too from gpio. So i search a quick way to get it work on a battery. I work and search on this since 5 week and i really need to get it work. Thx

I played a bit with the SenseHAT from the RPi guys. Doesn't work fully but I get the first things working. What does run: Joystick 8x8 led matrix (partly, seems that there are some parts of the framebuffer not fully working) What doesn't run: all the sensors attached on the board What's missing: load it devicetree overlay (at the moment it's coded into the main dts) how-to what's needed to get it working on your tinker too I'll keep you updated.

Hello, I want to install libdrm from here https://github.com/rockchip-linux/libdrm-rockchip But there are already problems with autogen.sh. See below. Does anyone have a tip for armbian (Debian stretch) on how to install this library? The Clash Spoiler $ ./autogen.sh autoreconf: Entering directory `.' autoreconf: configure.ac: not using Gettext autoreconf: running: aclocal --force -I m4 ${ACLOCAL_FLAGS} autoreconf: configure.ac: tracing autoreconf: configure.ac: creating directory build-aux autoreconf: running: libtoolize --copy --force libtoolize: putting auxiliary files in AC_CONFIG_AUX_DIR,…

Hello everyone, I've begun working to target the Armbian Legacy Tinker Board build to the Rockchip kernel. There are a list of reasons why it needs done, including some relatively large differences between the current kernel's code base and the Rockchip kernel (making it hard to patch with bugfixes/etc) and inactivity on the part of the vendor of that kernel. There are also reasons I am preferring to use the Rockchip kernel rather than the ASUS kernel. First and formost is the need to also support the MiQi. The miniarm branch of Rockchip and the ASUS kernel have board-specific fixes written in such a way as to not be friendly to other boards. I've dec…

linux-xenial-root-next-tinkerboard 5.38 with 4.14.14 kernel installed. armbian's apt repository has only 5.38. but packaged rom file from dl.armbian.com is 5.41 with 4.14.23. (Armbian_5.41_Tinkerboard_Ubuntu_xenial_next_4.14.23_desktop.7z) How to upgrade on linux latest armbian? It need waiting?

Hi all, Saw that via Slashdot. A RPI 3 b+ benchmark comparing against other SBCs and TinkerBoard. Check it out: https://www.phoronix.com/scan.php?page=article&item=raspberrypi-3-bplus Feeling great for buying one, after reading all 18 pages of the forum! Ah. A big shout THANK YOU to Igor, Tony, Kaiser and everyone else that helped build a working Armbian release to this SBC. -RF

Hi, i get a probleme with the actual uart acces config by default on Uart2 (pin 32, 33), because i need to use PWM pin (use to set motor speed with a L293D) and on the board only pin 32, 33 can be use with PWM. Now i am using 32 33 pin as PWM but if the cable on these pin is connected the board doesn't boot, maybe because the uarts of u-boot use these pin and the result of un connected cable to my setup = Critical fail. When i remove the cable on pin 32 the board boot. So i need to solve that because i don't want to disconnect this cable at each start and i want to use uarts with this setup. I need to change uart2 to uart1 or find a way to get PWM or a other pin option …

Is there a way to upgrade from an earlier version to 5.41?

Hello. Has anyone had success with setting up the onboard wifi on the Tinkerboard without the network manager? I have tried using wpa_supplicant to connect but not having any success. Here is what (I know works on an Intel Compute Stick running Ubuntu 16.04) I've tried: wpa_passphrase SSID password >> /etc/wpa_supplicant.conf wpa_supplicant -i wlan0 -c/etc/wpa_supplicant.conf -D nl80211 -B dhclient wlan0 dhclient just keeps retrying and goes no where, I don't get an IP address I can connect to my network using the Network Manager no problems, just can't figure out a way to get it to work with the network manager disable…

Greetings, I recently had a request about testing the I2S and SPDIF output of MiQi devices and after some fiddling on this board, it seems that the Rockchip I2S + Simple-Audio ALSA driver just output nothing on the I2S TX/RX pins, at least. So was anyone able to output sound directly through the I2S GPIO pins on any RK3288 device ? Tinkerboard devices seems to use that setup and it seems to be working, but I'd like to know if that's working through the soldered Jack or the GPIO.

Video demonstrating issues reconnecting to Wi-Fi please help

Hy, I miss a few options in the kernel current kernel: ARMBIAN 5.36 user-built Ubuntu 16.04.3 LTS 4.4.102-rockchip Thinkerboard I still need: 1) - disable HDMI audio so that it will no longer be displayed as a sound card under "aplay -l" deactivate "card 3: rockchipminiarm" same as with the image kernel update of Igor root@se:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Audio [USB Audio], device 0: USB Audio [USB Audio] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Audio [USB Audio], device 1: USB Audio [USB Audio #1] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Audio [USB Audio], device 2: US…

hi , i am using the gpio library provided by asus tinker board to work with gpio on armbian os . i am having issue with running the python script without giving sudo cmd. is there any alternative to overcome giving sudo all the time while running gpio python script or any other alternate library to use with armbian python add_event_callback.py can't open /dev/mem and /dev/gpiomem wiringPiSetup: Unable to open /dev/mem and /dev/gpiomem: No such file or directory Segmentation fault

This will be a catch-all for HDMI-related things. Sep. 29, 2017 UPDATE First up is hotplugging in Mainline. Script/rule added to build system. Thank you @botfap for the script I am getting the system events triggered saying the HDMI is unplugged/replugged, (using udevadm -monitor) however nothing is happening in response to the events it would seem, the screen is still blank. I could hook a script to the event, but I'm not exactly sure what I would tell it to do... Any thoughts would be great, I'll be researching.

Hello all, i have a pressing problem requiring urgent help. I am currently conducting my thesis with the Tinker Board and i have the Armbian Ubuntu desktop with the legacy kernel running. I noticed when i try to boot the system, it takes approximately 25 minutes to show the Login request in the CLI and after that, it creates the user account but instead of proceeding to the regular desktop page, it gets stock there and does not proceed. I will please like to know if anyone has an idea of how to solve this issue as i urgently need it to get running fast to run the tests needed for my thesis. Thanks.

Hey, I’m running armbian on a tinkerboard and I need to connect to a CAN-bus. Apparently the usual Linux CAN-kernel-modules aren’t shipped with armbian, so I guess I’ll have to add them manually somehow. I`ve been trying to do that for two days now without any luck. I’ve been trying to follow the steps described in other forums, but it haven’t helped. I really just want to add the necessary modules to my existing kernel. Any ideas?

Hey everyone I've compiled my own kernel using this awesome tool, and I'm now running it on a tinker board. Everything's been working fine, except for one annoying thing I just ran into: I can't use the GPIO pins. When I try to use a pin in python I just get this message back: "RuntimeError: This gpio is set to other function!". If I run Debian I can use the gpio just fine, but I need some kernel modules that doesn't ship with Debian. That's why I've compiled my own armbian kernel. Anyways, any idea on how to fix this? Any special module I should add when compiling the kernel? Thanks Marius

Hi, has any of you some experience connecting a Hifiberry Amp+ to a Tinkerboard - on Hifiberry pages this is now a possible connecting but I miss a howto and would really appreciate a quick start on this. Have previously succeed with Raspberry 3 and IQaudio - but intend to take a step further and do a project being more than just an amplifier. After testing several OS I have to admit Armbian has become my favorite and it is within this OS I hope to achieve this.

Are the are UART Gpio pins enabled by default? If not, how do I enable them? Sorry but I'm a linux noob.

We have so much trouble with wifi disconnects on around 30 tinkerboards. I'd be happy to donate to someone who works on the wifi to address the issues. Does anyone know where to go to to ask for help?

Hey! I recently got a CAN-bus up and running on a Tinkerboard running Armbian, but I've run into another problem here: The CAN-bus buffer fills up. After sending a few messages I get an error saying "No buffer space available". I've noticed that some other people are solving this by increasing the buffer size, but that seems like a weird solution to me. And it wouldn't really help me much. I need to empty this buffer when I read from it, or manually (without restarting the CAN-bus). Any ideas on how to do that? Thanks

Hi, On the download page of Tinker board "Ethernet driver needs some fixing" is listed as known issue. Are there any details about? What is the problem with the ethernet? Who should fix it? (Asus, armbian) Are there any plans for fixing it? I'm asking it, because I would like to use my tinker board as a headless 24/7 home cloud. Thank you!

Hi every body, I am a new user of Armbian and Linux based system. I wanted to use the Tinkerboard because of his 4K video processor (I am programming a special video application) I install Armbian following the steps of the site. Everything went good, the system is runing. I made all update an so on. Then I wanted to test a video (MP4 1920x1080) capability with the build in player, and the video is playing very slow. I try too a Youtube video, same thing... Meanwhile I installed a TinkerIOS linaro and TinkerOS android, video are playing at the good speed... So my questions are: 1) do we need a special video driver on Armbian for the ti…

Is there an official way of installing libmali drivers on Armbian? I'm feeling a bit slow, since I can't really figure out how to install them. It seems like files from this github repo will overwrite other system files, so it's not a solution that would work in the long term.

I hear something about a new version of the board Thinkerboard, "Tinkerboard S". I want to know what you know and think about it. https://www.asus.com/Single-Board-Computer/Tinker-Board-S/

There's a way to change the framebuffer display resolution / refreshrate? Via HDMI my display work at 1920x1080 at 25Hz, i need to set it to 60Hz

Hi, could someone just add TCP BBR module into kernel? pls

Hi I was struggling to find the right package for my Tinkerboard. I needed a reasonably powerful 24x7 appliance that could provide torrent downloading, wifi hotspot, a shared network drive and a LMS box. After trying out the Asus effort and DietPi - both with severe issues) I landed on Armbian and it seems to have everything going for it but the LMS install just does not work. I am a Linux newbie, I know my way around Windows and a GUI, and used the instructions here and a few other places to successfully set up the hotspot and the sharing and automounting of large USB drives. It took me the better part of 6 hours just to figure all of that out (j…

Sir, I have Purchase the Tinker board before 20 days, I install the Armbian 5.35 version in the Board, All software are very Nicely Work , but could not connect audio , I am trying to the 10 more times reinstall the Armbian 5.35 version but could not connect the audio output in audio 3.5mm Jack , I will so tired please solve this Problem in my tinker Board …

So my boss deploys a plethora of Asus TInkerboards to assist with production. We are currently using an OS image provided to us by this website---specifically, Ubuntu_xenial_next_desktop.7z. On some occasions, with kick ass access points, the tinkers will disconnect from the wireless network that we are using. We are also using an antennae attachment which seems to help a bit with connection issues. Without providing too much specific info, is there an updated driver being worked on somewhere that I could be pointed towards? Any info/words of wisdom would be very helpful! Thank you! Best regards and thanks in advance! Joey

Hey everybody, First, thanks for Armbian. The Asus Tinkerboard and the ROCK64 both have the same processor. I'm interested why the Asus Tinkerboard gets the mainline kernel, but the ROCK64 only gets the legacy kernel. Why is this?

Hello ! I see in config file of kernel 4.14 support for RTC ds1307. But in system i not see RTC. I just see RK808 RTC. I need your help for use DS1307 in my tinkerboard because rk808 is not fonctional ( no battery)

Hi out there! I've managed to build a quite complex system based on Tinker, using 1 Wire sensor, I2C-s, all of all UART's, and all of all remaining GPIO's... :-) Unfortunately a long term test in a climate chamber have failed... (although the core was just heated up to 70 degrees Celsius) The need for a hardware watchdog then arise... I've build new kernel using latest compile.sh with the HW watchdog checked resulting Linux tinkerboard 4.4.110-rockchip #2 SMP Wed Jan 10 16:41:03 CET 2018 armv7l GNU/Linux but there is no /dev/watchdog Not even in /proc/iomem at ff800000... …

I still have a problem configuring the wifi hotspot on the armbian distribution for tinkerboard. The hotspot is clearly unstable. So none of my computers can't connect to it and my phones and tablets have a unstable connection. I thought having found a turnover using a call to iw with a frequency of 1s. This was reactivating the wifi for some times (that should simulate a continuous connection) but it looks that it doesn't work anymore. So I am stuck with that, I am unable to configure a stable hotspot. Is there something to do with the rtl8723 driver, or have I no hope to make it works ?

Hi There are some guides on how to install Kubernetes on a Raspberry Pi cluster. I am trying to build such a cluster with Asus Tinker Boards as I think that these would make an even more powerful demo system. Unfortunately there are no guides for running Kubernetes on Tinker Boards. I am using Armbian Ubuntu Xenial mainline image which is running very stable. uname -a Linux tinkerboard 4.11.0-rockchip #19 SMP PREEMPT Thu May 4 16:08:16 CEST 2017 armv7l armv7l armv7l GNU/Linux When initializing the cluster with "kubeadm init" it runs into the following fatal error during preflight checks of the system: [preflight] Some fatal errors…

Does the armbian build come with 3D acceleration? Or is it 2d only?

Hello, I am using the latest Desktop Armbian and use the internal wifi and a usb wifi stick (edimax ew 7811-un). Both devices are detected by network-manager. I use network-manager to connect to my router. I get internet. Minutes later, there is DNS conflict (/var/log/syslog) and I cannot resolve any websites anymore. I only see dhclient DHCPDISCOVER on eth0 255.255.255.255 for some reasons. I have this problem with a fresh installed Armbian. How can I solve this? Thank you

https://www.cnx-software.com/2017/12/07/rockchip-rk3288-to-be-phased-out-soon-gpd-xd-android-console-to-get-mediatek-mt8176-soc-4gb-ram-upgrade/ Rockchip RK3288 32-bit Arm processor was first spotted in a company presentation in the summer of 2013, before being announced – with some confusion (Cortex A12 vs A17) – at CES 2014 in January. The quad core Cortex A17 processor had then its moments of glory with inclusion in products such as Chromebooks (2015) and ASUS Tinker board SBC earlier this year. “Rockchip are phasing out sales of the RK3288”, meaning most products based on the chip will soon be phased out or upgraded to another solution. …

Trying to set Wireguard (www.wireguard.io). I can compile and load the module (which is an issue on most distributions as they lack the necessary kernel headers), but bringing up the interface fails: root@tinkerboard:/etc/wireguard# wg-quick up mullvad [#] ip link add mullvad type wireguard [#] wg setconf mullvad /dev/fd/63 [#] ip address add 10.99.0.23 dev mullvad [#] ip link set mtu 1420 dev mullvad [#] ip link set mullvad up [#] wg set mullvad fwmark 51820 [#] ip -6 route add ::/0 dev mullvad table 51820 [#] ip -6 rule add not fwmark 51820 table 51820 RTNETLINK answers: Address family not supported by protocol […

Hello, I am using the lastest stable mainline kernel and would like to change my mac address before network-manager is started. I tried to change the mac address of wlan1 (which is an Edimax usb wifi stick) which works, but wlan0 (Tinkerboard internal wifi chip) gives me the message: Network driver didn't actually change to the new MAC!! Does it have something to do with the drivers used on Armbian? I am using sudo macchanger --mac 02:02:03:04:05:06 wlan0 Thanks for help.

Hi, i am new to single board computers and i tried almost every posible thing to make this work. DISPLAY=:0 xrandr --output HDMI-1 --brightness 0.5 and i also tried xbacklight, with no luck. Linux Debian 4.4.102-rockchip #3 SMP Fri Nov 24 19:01:14 CET 2017 armv7l GNU/Linux my xrandr output: kiosk@Debian:/sys/class$ DISPLAY=:0 xrandr Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 4096 x 4096 HDMI-1 connected primary 1920x1080+0+0 (normal left inverted right x axis y axis) 640mm x 360mm 1920x1080 60.00*+ 50.00 59.94 25.00 24.00 23.98 1920x1080i 60.00 50.00 59.94 1280x1024 60.02 1280x…

Hi, I've downloaded Ubuntu-mainline image at https://www.armbian.com/tinkerboard/ and written to SD as below but Hang while booting. # dd if=Armbian_5.35_Tinkerboard_Ubuntu_xenial_next_4.13.16_desktop.img of=/dev/mmcblk0 5742592+0 records in 5742592+0 records out 2940207104 bytes (2.9 GB, 2.7 GiB) copied, 481.509 s, 6.1 MB/s Log: U-Boot SPL 2017.09-armbian (Nov 22 2017 - 17:12:11) Returning to boot ROM... U-Boot 2017.09-armbian (Nov 22 2017 - 17:12:11 +0100) Model: Tinker-RK3288 DRAM: 2 GiB MMC: dwmmc@ff0c0000: 1 *** Warning - bad CRC, using default environment In: serial Out: serial …

So after installing the Armbian distro with hope that I can get monitor mode enabled on the built-in wireless card, it doesn't seem to be working. Both the aircrack-ng software or iw cannot seem to put the driver into monitor mode even though it shows as being a supported mode: mlinton@tinkerboard:~$ iw phy0 info Wiphy phy0 max # scan SSIDs: 9 max scan IEs length: 2304 bytes Retry short limit: 7 Retry long limit: 4 Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) * CMAC (00-0f-ac:6) Available Antennas: TX 0 RX 0 Supported interface modes: * IBSS …

This was working on the tinker debian release, so I'm thinking this sis some kind of s/w issue. Is there something I'm missing on how to enable this? Thanks! Dave

Hello. In Armbian 5.34 (default, next and nightly (26/10/2017) no have permission for create, edit and delet conection on network manager. To be able to modify a connection it is necessary to open the network manager in root. It's really very exciting. Looking on the internet it turns out that it will be a problem of "policy". I had already reported this bug on the post "tinkerboard". He had been tuned to a nightly version but he came back. my account is in the group netdev and sudo like ask in the polkit Would it be possible to have a "next" version fix this bug or have the procedure to fix the error? thank

Hmm... I have similar problem for Asus tinkerboard hangs thread's thing. First, I've reinstall OS few days ago, because OS partition is crashed by system hangs. I've test next build but it can't be reboot (I don't know why). cause I've install legacy build. It looks pretty works well, so I've install 'transmission-daemon' to build my own seedbox. I've plugged 500GB 2.5in External HDD and 128GB Flash Drive, and use 3A Micro-USB adapter. then... ta-da! system hangs! generally It works good 1~2 days after boot. but randomly hangs. I think it's temp things cause install Fan on 3.3V GPIO, but same. It hangs. B…

I have a USB-C charger rated for 3A, USB-C Cable rated for 3A, and a USB-C to MicroUSB adapter rated for 2.4A. Should I even bother testing that?

hi guys. I need to connect temperature sensor ds18b20 to thinker board on w1 (one wire) how is posible to put on ??

Hello, i will move my project from RPI2 to tinkerboard. I have 2 Serial Converter, USB to RS422 and USB to RS485, both working on the PI. On the Tinkerboard with "ARMBIAN 5.33 stable Ubuntu 16.04.3 LTS 4.13.3-rockchip" runs only the RS422, the RS485 (Vendor 1a86) is not available as /dev/ttyUSB. What can i do? Regards Marco Tinkerboard Log: Spoiler Oct 14 17:52:45 localhost kernel: [ 1.942542] usb 1-1.1: new full-speed USB device number 3 using dwc2 Oct 14 17:52:45 localhost kernel: [ 2.020053] usb 1-1.1: New USB device found, idVendor=1a86, idProduct=7523 Oct 14 17:52:45 localhost kerne…

Has anyone played with kvm or xen on the hw-virt capable rockchip devices? Im trying to setup a simple kvm scenario. Im using Armbian tinker stable and the excellent @Myy 4.13 kernel and have configured it for guest and host support. Im struggling to get the boards up in "Normal" (PL2 / Hyp) mode. I can only get them to boot in "Secure" mode, which is the normal method of boot. Secure boot disables access to Privilege Level 2 and the ARM Hypervisor which makes virtualisation impossible. I have tried setting "bootm_boot_mode=nonsec" but it makes no difference, I still get "kvm [1]: HYP mode not available" during boot. Same as I get with "bootm_boot_mode=sec" wh…

Hello, I usually use the Next version of the image for the tinkerboard. I would like to use the nightly version. But the nightly version does not automatically log on to the user I created at the beginning in contradiction to the other version. How do I reactivate automatic login in nightly build ? Thanks

Hi! With I tinkerboard I installed the Ubuntu Desktop - legacy kernel. I wanted to try the linux-image-next-rockchip, but it had some problems (new IP address at each boot), so I wanted to go back to linux-image-rockchip. When I installed linux-image-rockchip, I got 4.4.73-rockchip and not 4.4.88-rockchip which I had before.

*Updated 7-23* ~~All kernels should be fixed at this point, Legacy, Next, and Dev.~~ The ASUS Tinker Board has a big problem with rebooting properly, centered around the SD card power supplies. Upon issuing a shutdown request, the kernel is turning everything off , including the vmmc regulator. To make matters worse, vqmmc is set to 1.8 Volts if you use a UHS SD card, and the kernel is not switching it back to 3.3 volts before rebooting, which is required if the Rockchip boot ROM is to communicate with the device. The result is a hung board in MaskROM mode. For the Default kernel (4.4), a patch was carried over from the vendor softwa…

Anyone having luck getting firefox quantum to run? I added the ppa and installed it but it crashes immediately.

Whats the correct way to get the Armbian build to spit boot out as a separate fat partition at the start of the image? Im just getting started with Armbian (on tinker board) and want to integrate it into by own build system. I need to generates SD card images with 3 different configs building 3 separate installs sharing a common multiboot 512MB fat boot partition. I dont need the Armbian build to do the multiboot or manage the boot partition at all, I just want to be able to extract the root & boot fs at the end of the build process.

Does anyone know what to do to enable 1920x1200 resolution? I've done the xrandr newmode/addmode and it shows in the display app but doesn't work. At the command line... xrandr --output HDMI-1 --mode 1920x1200_60.00 xrandr: Configure crtc 0 failed The monitor and tinker board support 1920x1200 and it works with tinkeros.

Just started using the thinker board, and got fed up with the OEM builds which brought me here. So I would like to thank everyone for all the hard work, Im sure it can't be easy fixing things blind! Cheers mates. As the Tinkerboard runs hot under load, i run a program that adjusts pwm to adjust fan speed. so I noticed right away when upgrading to 4.13.0 that both soc and gpu thermal zones had broken. I've tried 4.13.1 and 4.13.2 as well they are broken as well. 4.13.x all kick error messages into dmesg as well. root@Asus:/sys/class/thermal# uname -r 4.12.0-rockchip root@Asus:/sys/class/thermal# cat /sys/class/thermal/thermal_zone[1-2]/temp 32…

Hello! I've been using Armbian on my newly bought Tinker Board for less than two weeks now and I've to say that the work you guys have put into this is incredible! It truly is remarkable and inspires us newcomers which haven't started studying computer science or are currently studying - as myself. So, I will definitely contribute and help others in the future to increase the Armbian community! However, as I'm new to Unix, Tinker Board, everything that's not Windows or Mac OS, I've a deep learning curve ahead! Let's start with my setup: Build: ARMBIAN 5.32.170921 nightly Ubuntu 16.04.3 LTS 4.14.0-rc1-rockchip (I know it's nightly so there are bugs, ye…

I'm using Armbian_5.32.170920_Tinkerboard_Ubuntu_xenial_dev_4.13.0_desktop.img (yes I know it's a nightly) and it works great. However if I run "apt-get upgrade" something gets "upgraded" and the display no longer works. I've tested this on multiple tinkerboards with the same results. The tinkerboard is running, I can ssh into it. Just no display. dmesg output: Spoiler armbian@tinkerboard:~$ dmesg [ 0.000000] Booting Linux on physical CPU 0x500 [ 0.000000] Linux version 4.14.0-rc1-rockchip (root@armbian) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4)) #2 SMP PREEMPT Wed Sep 20 11:37:48 CEST 2017 [ 0.000000] CPU…

Hi! I'm using Tinker board with armbian 5.31 stable (Ubuntu 16.04.3 LTS 4.4.73-rockchip), and using this as File Server. Cause i've install lighttpd and php7-0-fpm, and install Nextcloud (Owncloud). HTTPS is installed using Let's encrypt certification. Network is directly connected broadband, Half-Giga network. It looks working smoothly but little slow. BUT it's not. it's stuck on every file downloading. It's occurred both HTTPS and HTTP. First, HTTPS file downloading is stopped unexpectedly, cause can't download any files. HTTP is same but automatically resume, cause download is can be completed. …

Hi, I am looking for owners of RK3288 who can help to find missing information in the system. A lot already works from the template. Vcore has been added thanks to @TonyMac32 , but some important information like RAM frequency (dynamic.5.name=dram_frequency) is still missing. This is my adjusted version, but to do some more HW testing we need as much information about the board as possible. Spoiler web.page.icon='img/logo.png' web.page.menutitle='RPi-Monitor _{('+data.hostname+')}' web.page.pagetitle='RPi-Monitor ('+data.hostname+')' web.status.1.name=Raspberry Pi web.statistics.1.name=Raspberry Pi web.addons.…

Let's make a topic dedicated to the latest issues with the latest Linux Release Candidate provided on the Linus Torvalds git repository. So, on the 4.13.0-rc6, I got a crash on boot on my MiQi devices due to some changes in the logging functions used by the STMMAC Ethernet driver. I reverted some of their changes by just commenting the new logging function. I'll try to get in touch with the person who wrote the commit that generated this issue, as he tends to roam in the #linux-rockchip IRC channel. Meanwhile, here's the patch : https://github.com/Miouyouyou/RockMyy/blob/master/patches/kernel/v4.13/0012-net-stmmac-Reverting-a-part-of-Use-…

Hi, i just tried to install ubuntu 16.04.2 on my tinkerboard, but i got a problem while changing the password as prompt on the first boot : when i try to change it, by anything i write, it just give me that message i use as title. can anyone give me help ? i dont find anyway to go further.

I would like to setup NTPD with PPS but seems GPIO PPS is not yet supported. Anyone working on this?

Hi I have a Philips pcf8563 RTC that connects to i2c-1. Could you please add support for RTC modules please particularly the pcf8563 and the DS1307 as these seem to be the most popular although some more models would be welcome. I have been trying to create a dtb with a previous kernel that included the needed modules but failed to get it to compile. I even tried adding it to the main device tree with no such luck. I know it's not been talked about much but would love to get RTC working on the tinkerboard. For those that haven't noticed the RK808 power management chip on the tinkerboard has RTC capability built in and even has the drive…

It doesn't detect any wifi network. And when I run iwconfig. wlan0 doesn't appear (only eth0) What can I do?

Hi, i want to disable the "rockchipminiarm" sound card: root@innotune:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Audio [USB Audio], device 0: USB Audio [USB Audio] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Audio [USB Audio], device 1: USB Audio [USB Audio #1] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Audio [USB Audio], device 2: USB Audio [USB Audio #2] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: rockchipminiarm [rockchip,miniarm-codec], device 0: ff890000.i2s-i2s-hifi i2s-hifi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 I wanted to add the module of the soundcard into /etc/modprobe.d/blacklist but i…

So, if you use the mainline DTSI files, you'll encounter an issue when loading the Mali Midgard GPL kernel module, since the main ARM kernel maintainers changed how the "compatible" properties of Midgard GPU nodes should be defined. Don't ask me why, they created an entire documentation stating that now the Mali Midgard GPU nodes have to harbour the chip series number, a vendor-specific statement, and drop the "arm,mali-midgard" property. The additions are nice, since they allow a quick detection of the chip number and the chip vendor using /sys nodes names. However, turns out that the Mali kernel driver used the dropped property to detect the GPU. So, I've …

Just got my new tinkerboard powered up with armbian. For some reason I could not get anything after build 1.3 off the Asus site to boot! Anway, first impressions good, however in the graphics settings it seems to max out at 1920 x 1080 whilst on paper the tinkerboard is supposed to support 4k. I'll admit I am new to linux so perhaps i'm missing something ovbious, but if someone could explain how I can up the resolution to 3,840 x 2,160 that would be great. For the avoidance of doubt I have it connected to an Acer 27" 4k monitor.

I've installed the Armbian distro for Tinker Board, updated it, fiddles with PulseAudio settings, added Codecs but for the life of me I can't get any audio from the headphone jack. Hopefully someone can suggest a solution. TIA.

Hi all, looking for a bit of advise. I had an idea recently in that I have a problem of syncing a 20Tb USB 3.0 RAID0 drive with a 20Tb NAS. I have two fully duplicated RAID0 drives with no protection, so whenever I upgrade the capacity of a drive, I do a full sync. I do this maybe once a year. Whenever I have to do a full sync however it usually ties my MacBook up for a few weeks to transfer that much data over, so I had the idea recently of having a maker board do it since Linux/Armbian supports HFS+, I can just do an rsync between the two. I opted to purchase a Tinkerboard for the GigE Ethernet (I'll live with the USB 2.0), installed, up and running all…

Hi out there! F.Y.I. I've tried a lot of things to customize the kernel for Tinker Board on 32-bits host platform, but finally I gave it up. Instead other messy things, I followed the armbian instructions exactly, and successfully created an Armbian_5.32_Tinkerboard_Debian_jessie_default_4.4.76.img using the comile script on the recommended Ubuntu host. Unfortunately the resulted image does not boot: root@eepc:~# ttysh /dev/ttyUSB0 -s 115200 U-Boot SPL 2017.07-armbian (Jul 18 2017 - 17:40:48) Returning to boot ROM... U-Boot 2017.07-armbian (Jul 18 2017 - 17:40:48 +0200) Model: Tinker-RK3288 DRAM: 2 GiB…

Hello, I have Tinker Board. If I install Armbian I see screen only over HDMI. I would like to enable DSI touchscreen display. Is it possible? How make it? Thank you

Anything targeting the mainline will be getting 4.12 tonight, I can confirm some patch failures for Tinker Board/MiQi NEXT, Specifically: 0002-Adaptation-ARM-dts-rockchip-fix-the-MiQi-board-s-LED Was patched in the kernel. 9002_dts_rk3288_updates - Fixed and the packaging postinstall-scripts patch specific chunk: scripts/package/builddeb There is no "Provides:" statement.

I confess, I have no idea what to do with the contents of this repository. Any help would be great, as I've said before, my Linux experience is lacking on things, the work I do is usually in hardware with kiB of RAM... I'm working on the assumption that this would be the best lib to install, if I'm wrong, let me know. https://github.com/rockchip-linux/libmali

Hey My Tinker board is my first dev board and it runs damn hot, I saw this and it says its for the PI, can somebody in the know tell me if It would work on the Tinker Board please. I am running Armbian Ubuntu server temp fan control Thanks!

Hello Forum, i just got my new tinker board running with armbian, thanks for the good work ! I want to set up a vdr vnsi server on this to replace the existing Raspberry 2. To get the DVB USB Skystar Tuners running several modules out of kernel/drivers/media like dvb-core and usb are needed. Are this kernel drivers already compiled available or what to do to get them ? Thanks Thomas

I build a kernel last night because I wanted a headless debian based system, not the nightly desktop available for download. Everything went well (almost*) until I tried installing NFS Apr 21 09:16:39 tinker1 rpc.idmapd[7408]: main: fcntl(/run/rpc_pipefs/nfs): Invalid argument Apr 21 09:16:39 tinker1 nfs-common[7394]: Starting NFS common utilities: statd idmapd failed! Apr 21 09:16:39 tinker1 systemd[1]: nfs-common.service: control process exited, code=exited status=1 Apr 21 09:16:39 tinker1 systemd[1]: Failed to start LSB: NFS support files common to client and server. -- Subject: Unit nfs-common.service has failed -- Defined-By: systemd -- Support: http:…