Beginners

Good afternoon, I have just started studying the use of embedded arm linux for single-board computers. I'm asking for help from experienced developers. I have an orange pi lite. I uploaded a prebuild minimal armbian image to the microsd card: Armbian_community_25.5.0-trunk.444_Orangepilite_bookworm_current_6.12.23_minimal.img.xz .After that, I installed mate desktop environment according to these instructions: https://forum.armbian.com/topic/28786-install-mate-desktop-to-minimal-image-blues/. The problem is that the processor heats up very much under load (I registered a temperature of 95 degrees celsius using armbianmonitor) and periodically turns off due to overheating.…

I'm currently in the process of deciding between the Orange Pi 3B and the Raspberry Pi 4, and i'd love to hear your thoughts. I know that Raspberry Pi has a huge community and a ton of resources, which is super appealing for someone like me who's looking to learn and tinker. The support from the community is definitely a big selling point, especially since I'm just starting out. That said, l'm also considering the Orange Pi because it's much more affordable. The price difference is hard to ignore and l have heard it's a pretty solid option for DlY projects and development. Plus, l'm thinking ahead - l might want to stick with Orange Pi for future projects as well, sin…

Hi All, I just want to ask what is the format of rootfs after writing it to nand? it is in ubifs? Thanks

dear guys, I use banana pi, root@bananapi:~# uname -an Linux bananapi 4.2.3-sunxi #2 SMP Sun Oct 11 14:12:18 CEST 2015 armv7l armv7l armv7l GNU/Linux I have asymetric route, packet go out from one interface and comes in from another interface (tunnel ). already made 0 for all interface in /proc/sys/net/ipv4/conf/*/rp_filter ip_forward already enabled. i dump packet comes in succeed to our banana. but when i test using ping command, doesn't respond with reply. any suggest ? thanks

Hi, is possible to include more gadgetfs kernel module on a64 legacy kernel configuration?

RK3399 which is running Ubuntu operating system is not identifying USB camera as CAPTURE device. So I am not able to use command line utilities like ffmpeg to capture the video data from device.

I have a device on a20, I tried to start an image from Cubietruck, everything works, but I am interested how it is possible to disconnect an error sun7i-dwmac 1c50000.ethernet: Failed to reset the dma. There is no Internet connector on the Board I attach the log Apparently the script is constantly trying to raise the connection, but I do not know how to disable it. I would be grateful if someone can tell how to do it

Sorry if this is the wrong place. I'm a noob to all this. I've searched the help files, Google, forum posts and can't find anything regarding a tinker board and no signal issue. I've only been able to find posts about Rasberry Pi Orange, and the solution used in those posts don't seem to apply here. I have an Asus Tinkerboard (not the S). I bought a 7" HDMI touch screen which was advertised as being Rasberry Pi compliant. 7" 800 x 480 HDMI-B TOUCHSCREEN FOR RASPBERRY PI https://www.velleman.eu/products/view/?id=439070 This screen doesn't use pins, just an HDMI port out. I've flashed different versions of Debian Stretch, Ubuntu, Debain based RetroPie imag…

I'm getting some strange behavior with the new image when trying to enable OMV on my T4. Its always installed no problem, but now when I try to do a clean install Im getting the below info. Although after reboot the box is checked in softy to suggest OMV has installed ok, I haven't gone far enough in configuration to see if anything isn't working. Can anyone tell if Im doing something wrong? (I also experienced similar behaviour in Buster but I had no prior working installation's to suggest its a bug or me) --------------------------------- Executing: /tmp/apt-key-gpghome.wBAnSaHxyZ/gpg.1.sh --keyserver hkp://keyserv…

how to make orange pi one connect to the internet by rj45 cable with using vnc viewer?

First of all sorry for the newbie's question. I compiled a kernel with custom configuration to use this instruction: https://docs.armbian.com/Developer-Guide_Build-Preparation/ OS: Ubuntu Bionic 18.04 x64 apt -y install git git clone https://github.com/armbian/build cd build ./compile.sh \ BOARD=orangepizero \ BRANCH=default \ BUILD_DESKTOP=no \ KERNEL_ONLY=yes \ KERNEL_CONFIGURE=yes After the kernel build is complete, the output directory contains output/config linux-sun8i-default.config output/debs /extra armbian-config_5.99_all.deb armbian-firmware-full_5.99_all.deb armbian-firmware_5.99_all.deb linux-headers-sun8i_5.99_armhf.deb linux-image-sun8i_…

So I just got my Orange Pi Prime board today and I tried the Ubuntu Bionic desktop image on it. (Armbian 20.02.3 Bionic current 5.4.18 desktop) Things didn't go like I expected... When I got into the desktop, all I saw was a missing taskbar, a white background (instead of a grey one) with a penguin on it. However, all the items on the taskbar worked normally. I thought that wasn't much until I tried to open Chromium, the whole window was white and I couldn't interact with it. I couldn't open the terminal either (clicking on its entry in the menu didn't launch it) I was shocked as I thought something was wrong with my board. So I told myself …

Hey guys Hope everyone doing well I have a Orange Pi Zero running 21.02.2 Focal and Pi-hole installed. When I run "sudo apt update" this is the output: root@PiHoleNapoli:~# sudo apt update Get:1 http://deb.debian.org/debian stable InRelease [116 kB] Hit:2 http://mirrors.dotsrc.org/armbian-apt focal InRelease Hit:3 http://ports.ubuntu.com focal InRelease Get:4 http://deb.debian.org/debian stable-updates InRelease [39.4 kB] Get:5 http://ports.ubuntu.com focal-updates InRelease [114 kB] Ign:6 http://deb.debian.org/debian-security stable/updates InRelease Err:7 http://deb.debian.org/debian-security stable/updates Release …

latest version build orange-pi-pc-plus with some ld error: ./compile.sh docker /root/armbian/cache/toolchain/gcc-arm-8.3-2019.03-x86_64-arm-linux-gnueabihf/bin/arm-linux-gnueabihf-ld: fs/sync.o:(___ksymtab_gpl+__sync_filesystem+0x0): undefined reference to `__sync_filesystem' make: *** [Makefile:1185: vmlinux] Error 1 Displaying message: Compiling current kernel 5.15.37 info Displaying message: Compiler version arm-linux-gnueabihf-gcc 8.3.0 info Displaying message: Using kernel config provided by user userpatches/linux-sunxi-current.config info Displaying message: Compressing sources for the linux-source package Displayi…

is there a chance that I could find older version of armbian for my sbc (orange pi pc plus)? in this case I need armbian buster for my sbc

Good day, I hope this email finds you well. I would like to create a custom animated screensaver and splashscreen on my Linux Armbian. I am current running the Jammy KDE Plasma version. Can you please guide me on how I can get this right and what I need to do to achieve this? I am also experiencing some graphical issues where some of the words disappear? Is there a fix for this? I am also trying to access the internet through wifi but it does not allow me to connect to my network. Any advice on how to get this right? Looking forward to hearing from you.

Dear to all, I'm not expert. How can I add kernel header of zfs to linux kernel 5.15.80-rockchip64? I have run the command "apt install dkms zfs-dkms" and I've got the following output: Reading package lists... Done Building dependency tree... Done Reading state information... Done dkms is already the newest version (2.8.4-3). Suggested packages: debhelper Recommended packages: zfs-zed zfsutils-linux linux-libc-dev The following NEW packages will be installed: zfs-dkms 0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded. Need to get 2297 kB of archives. After this operation, 18.0 MB of additional disk space will be used. Do you…

Now that xradio has been enabled on kernel 6.x, I'm ready to upgrade my Orange Pi Zero that I've been keeping on 23.02 with kernel 5.x. With armbian-config I've unfrozen kernel/firmware updates and after apt upgrade and reboot I am on kernel 6.1.53 and wifi is working! But boot message says I'm still on 23.02, and apt says that armbian-bsp-cli-orangepizero is being kept back. Now trying: $ sudo apt install armbian-bsp-cli-orangepizero [...] Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been mo…

Hi, I'm trying to compile Armbian with TOC0 support for my opi-zero2, but am having difficulty getting the configuration setting to take effect. Opening the compiled disk image in a hex editor shows me what I believe is evidence the current u-boot does not have the toc0 flag set: I started by creating a patch file in userpatches: userpatches/u-boot/v2023.10/board_orangepizero2/orangepizero2_toc0.patch diff --git a/configs/orangepi_zero2_defconfig b/configs/orangepi_zero2_defconfig index f13735e91c..31f3c475e4 100644 --- a/configs/orangepi_zero2_defconfig +++ b/configs/orangepi_zero2_defconfig @@ -23,3 +23,4 @@ CONFIG_SPI=y CON…

Oops, I connected a 24V power supply to the SATA Hat and I think I blew the diode on the hat. (see photo) Not sure if it is a diode, which way should it be orientated. Stupid idiot for creating the magic smoke, I hope I can repair it. I tried booting the Orange Pi I had already connected to it (because the original NanoPi M4 is missing... Fortunately the OrangePi is OK. Any advice on where to look if the diode in question does not fix it. Cheers, James

orange pi 5, orange pi 5 pro, orange pi 5 ultra or orange pi 5 max?

Hello everyone, first i want to say sorry if this post is not in the right place. I decided to post this in Armbian forum first, because I use it and it was awesome linux distribution with good community and support. I started as a hobby to write a software about controlling relays, to switch things in my home, like light, water heater, floor heater, etc. Hardware passes from PicoIP , thru wireless routers and finish on Orange PI, it offers a lot extras for it's price. What I have done so far: (all is in web interface, written from scratch) You can: switch on/off relays switch on/off relays for period of time schedule …

Hi, I'm wondering can I build the armbian for BPI-M3? I've tried this way: ./compile.sh BOARD=bananapim3 It fails on rootfs creation (I've tried to select CLI Xenial or Jessie): [ error ] ERROR in function create_rootfs_cache [ debootstrap-ng.sh:137 ] [ error ] Debootstrap base system first stage failed Can it be fixed?

I am considering building a development machine for building images, and Debian packages (deb). I do not plan a GUI on it. I plan to ssh in. I would like to be able to mirror a couple of SATA drives for safety. Speed and connectivity are important. Can anyone make a suggestion on what board. Must run Armbian of course. Thanks, Steve

Hi. After installing OpenVPN (apt install openvpn) I'm trying to run a VPN client on ARMBIAN 5.38 (9 stretch) 4.14.18-sunxi and I'm getting the following error when executing: sudo openvpn --config /etc/openvpn/client/myVPN.conf In the /etc/openvpn/client there are while the myVPN.conf file looks like # Specify that we are a client and that we # will be pulling certain config file directives # from the server. client # Use the same setting as you are using on # the server. # On most systems, the VPN will not function # unless you partially or fully disable # the firewall for the TUN/TAP interface. dev tun # A…

I've tried various methods. None work. What are the recommended Armbian ways to a) enable IPv6 temporary addresses b) disable IPv6 Thank you.

Hi, I would like to add gt9xx driver on my oppipc+. I use legacy xenial desktop 3.4 image and my touchscreen is GT911. I have source codes and makefiles. How can ı do it? ı'm noob at linux-kernel and sorry about my english. Eien. Thanks for replies...

Greetings, I set up an an armbian build environment, and went through the initial build, which took some time. Subsequent rebuilds took a couple hours as well, and I discovered I could 'skip' rebuilding the kernel unless I wanted to build it. Now, I'm testing customize-image.sh, things aren't always going where I want. so, I troubleshoot, make changes, but now my minimum build time is 30-40 minutes. Is there something else I can do to speed up the process?

I can't synchronize the clock using my GPS module. I get this error message: ntpd[1345]: kernel reports TIME_ERROR: 0x41: Clock Unsynchronized It only appears when I use my GPS source. When connecting to NTP servers, everything is okay. http://ix.io/2nUZ I tested it with older kernels, and it works, but I have then other issues. Any help are welcome.

Hello again all, Following the success of my last need to post here I changed my Odroid N2+ Plex server over to Armbian (making two Armbian-running Odroids in the house). The N2+ is running Debian GNU/Linux 10 (buster) with Linux 5.9.6-meson64 I have had a few occasions where I have encountered a system-wide freeze. Today's lasted over an hour, whilst others have unfrozen after ~20-30 minutes. Today the machine was ping-able but attempts to ssh in were unsuccessful though there was no timeout and no error messages when trying. Prior to that I was listening to some music in which the playback was faltering, leaving silence for several seconds duration b…

Hi all, I played around with home assistant on my Odroid HC1 (running NCP as main task) and now wanted to remove home assistant completely because I don't need it anymore. I tried to uncheck the software in Softy but that doesn't have any impact. How can I completely remove home assistant? Thanks!

Just installed Armbian on a Rock Pi4 to run OMV as a nas. I have a desktop installed. Install went OK but I have a weird problem, the menu has a different language for some items. Items in the main menu that have sub-groups have the other language, not sure what it is, possibly Cyrillic, but the sub-groups are in English. So, for instance, under accessorioes, accessories is not english but everything in its pop-up menu is. I've set the locale and language to GB, I'm in the UK but the menu doesn';t change.

Howdy, everyone! My apologies if this answer is available elsewhere, but I haven't been able to find it. I'm trying to better understand Armbian's policy toward closed-source components. Discussions on closed-components often times get confusing because "component" is overloaded, so I'm separating "components" into several categories: 1. Firmware/microcode that is loaded into hardware but never executed by the operating system itself 2. Drivers that operate in kernel space (often called "binary blobs") 3. Software that runs in user space 4. Firmware for "autonomous subsystems" or "coprocessors" like the Intel Management Engine or ThreadX on the Ra…

Hey guys, brand new to linux so sorry for obvious/easy question being obvious/easy I wanted to set up Pi Hole on my new Renegade, but I cannot figure out how to make/find a static ip address. I have found the IPv4 settings, tried to create an ip address in there, but I don't think it worked. Thanks for any help or advice you can give me, after I get the static IP address set hopefully I won't have any more problems setting up Pi Hole. Thanks again!

My environment is ManjaroLinux, x86 with docker installed on the system, I want to build the system for orangepizero3 via Arbian/build, I chose the CSC version, but there is an error during the build process, here is the log file:log How should I this problem? Thanks.

The usual way to get the a headless linux box up and running is to flash a disk image to a µSD card and then insert that card into the linux box, boot, answer some questions and it's done. Can I not do the same thing with an image file that I put on the µSD card (in addition to the µSD card having a complete linux OS that the box can boot from) and copy that to the emmc? Then pull the card and boot from the emmc? Does the image file used for a µSD card differ from the image file that should be written to the emmc? e.g. I have an armbian image, say "Armbian_25.2.2_Rockpi-s_bookworm_current_6.12.15_minimal.img.xz", on my µSD card at /media/…

I'm trying to run the following on edge devices, the remote interface to which does not support a traditional terminal (i.e. no interactivity): armbian-config --cmd ROO001 At the conclusion of this command running, the user is prompted through the UI/TUI to reboot the device. How can I avoid this reboot prompt, and just proceed with the reboot immediately? e.g. the Raspberry Pi OS raspi-config tool allows for the nonint parameter to be passed: raspi-config nonint enable_overlayfs The intent is to automate enabling of the read-only fs. Hardware is various Raspberry Pi and ROCK Pi devices running Armbian. I've already conf…

If you've tried hardware video on an Allwinner A733 (Orange Pi 4 Pro, Radxa A7Z), you've probably hit this: there's no V4L2 decoder, and omxh264dec advertises video/x-raw(memory:DMABuf) but aborts in gst_omx_video_dec_negotiate if you actually ask for it. So everyone falls back to videoconvert ! ximagesink and burns ~1.8 CPU cores on 1080p. The vendor OMX component reports the proprietary colour format 0x7f000002 through a malformed port-format enumeration, so gst-omx can't build a negotiation map. You can chase that a long way. Don't. libOmxVdec.so is a wrapper over libvdecoder.so, and that lower library is what actually owns the decode surfaces. VideoPicture.n…

Hello, I wish to share my research on getting OpenGL to work on Mali GPU. I realize Armbian focuses on server images, but I suppose many people would be interested nevertheless. I have a Banana Pi Pro and an Orange Pi PC, which both have a compatible GPU. Perhaps it will work on other boards as well. Here are the commands I used to get OpenGL to work. 1. Install: # install GLX Gears, mesa GL and GLU libraries apt-get -y install mesa-utils # install development tools apt-get -y install build-essential automake pkg-config libtool ca-certificates git cmake subversion # install re…

Today I installed the armbian build "system" as suggested by @Igor in some threads (VirtualBox with Ubuntu 16.04 64Bit and a GitHub clone). After generating a armbian 5.38 (with old kernel, bad WiFi and USB unuseable for WiFi or Ethernet) for my OPi i96 I did see that also a entry is for the BananaPi M2 Ultra. I got the little brother - the BPi M2 Berry - so I created also a image for an sd-card At the fist try I did no connect to the board (I know video driver isnt there). Ethernet isnt recognized (no DHCP and no device). The first connect I did get with a USB-WLAN Dongle (RTL8192CUS from edimax) while using a USB-TTL-seria…

Hello! In the process of setting up the settings in my new Armbian Bionic install on a 16 GByte installed MicroSD, I tried to set the clock preferences in the XFCE4 but as soon as I close the preferences application, it reverts to an invalid state and the clock disappears. It wasn't a fresh MicroSD and I'm concerned that it's trying to "save on a bad sector" or something when I set up the preferences. Is there a way I can test for the possibility that my MicroSD is wearing out? The power supply I'm using came with the board and has been adequate for all other OS uses. It may just be a file permission bug or something needing a "sudo". Either way, I'm conc…

Hello! I bought an Orange Pi PC about two years ago which is still working perfectly to this day (very happy with it), but I am curious to know what would be considered the 'best' Single Board Computer at this time point time, which would be around the same price range ($15 USD). 'Best' being defined as having a decent processor, and good software support - which the Orange Pi PC eventually did. I'm tempted to just buy another one of these for another project, but interested to know. Again, the main factor is price - $15 USD or less would be ideal.

Hi, I'm using LCD panel[1] and OV5640 camera sensor on SoPine and Pine64 LTS and trying to follow steps mentioned here[2]. It hangs while graphics initialize Welcome to Ubuntu 16.04.5 LTS! [ OK ] Created slice system.slice. Starting Accounts Service... [ OK ] Started Accounts Service. [ OK ] Reached target graphical.target. << hang here >> any help? [2] http://wiki.pine64.org/index.php/SOPINE_Armbian_LCD_and_Camera [1] https://www.pine64.org/?product=7-lcd-touch-screen-panel

Hi people, I need your help, I have been struggling to make this method work (https://github.com/zador-blood-stained/fel-mass-storage or https://github.com/ThomasKaiser/sunxi-armbian-flasher-osx) on the A20 processor for several days, but nothing works, I use Einstein-A20 (https://mega.nz/#F!ZtwxCCJC!AIYHcTqz-ucjuzKnE9qD7A?5xZ3iT4J) and enter the FEL mode using the special button UBOOT_SELECT. I made my own support for this board for uboot (_defconfig, .dts) and compiled u-boot-sunxi-with-spl.bin (Scroll down). script.bin took from cubietruck. That is, I use the h3 folder, only: zImage, uInitrd, boot.scr Сonnect the board in FEL mode t…

We have a home nas device based on Rockchip platform. Ubuntu base requires a license for commercial product. I wonder if we could use armbian as rootfs?

I don't want to talk about how long i beat my head against this but i have it working so i thought i would share. First, in the 5.4.y kernels, the fbtft_device module seems to be missing? So i am using 5.90 oragepizero ubuntu bionic next 4.19.57 as my image, kernel is upgraded to 4.19.62-sunxi via regular apt-get upgrade. I have a genuine waveshare 2.8 A rpi lcd. Waveshare states repeatedly that it is compatible with the 3.2 B rpi lcd except for the screen size and number of buttons, so this should work for the 3.2 B lcd as well. This blog post was pretty helpful: https://kaspars.net/blog/spi-display-orange-pi-zero But it …

Hi Trying to install docker (arm64) via the debian documentation on Docker's website, but running into persistant problem with dpkg on docker-ce. This is a fresh install (good SD card) of Armbian_20.08.1_Nanopim4_buster_current_5.8.6.img. (Made with dd, I confess). No ssh yet, so I'll handtype the some terminal output: ... Job for docker.service failed because the control provess exited with error code. See systemctl status docker.service" and "journalctl -xe" for details. invoke-rc.d: initscript docker, action "start" failed. - docker.service - Docker Application Container Engine Loaded: loaded (/lib/systemd/system/docker.service; enabled; vendo…

I'm trying to get mcp25xxfd device to work on OpenWRT. Currently I'm using ramips platform (Linux Kernel version is 4.14.180). I have the following configuration in one of my DTS files: osc: oscillator { compatible = "fixed-clock"; clock-frequency = <40000000>; }; spidev1 { compatible = "spi-gpio"; gpio-sck = <&gpio0 25 GPIO_ACTIVE_HIGH>; gpio-mosi = <&gpio0 26 GPIO_ACTIVE_HIGH>; gpio-miso = <&gpio0 27 GPIO_ACTIVE_HIGH>; cs-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; num-chipselects = <1>; …

ix.io/48Zd I've simply installed Armbian 22.05 Jammy Kernel 5.15.y, Size: 307Mb, Updated: Jul 2, 2022 on my aforementioned subject title / tagged OrangePiPCPlus. I can't seem to get hassio to install with armbian-config and then with Software > Softy it doesn't seem like the image for homeassistant io gets pulled, because when I check with docker images list or docker ps I don't get anything returned. Plus the checkbox isn't checked in Soft for hassio when I go back. What could I be doing wrong here? I did install Docker first, anyone have any tips?

Hey guys, I am pretty new to this. I am working on turning my Le Potato into a TV shuffler. I have decided to go with Armbian, since I can't SSH (which is required for the CoreElec method), because I use college internet, and it just isn't configured properly. I am currently trying to get a script going that will open a folder and begin randomly playing videos from within, but I cannot figure out where to start really. I think I need to import mpv into the script somehow, but I honestly cannot find any resources on how to do this. Any help is appreciated, thanks in advance.

I have a usb sound card on my sbc. Im only getting left channel audio. Ive tried a different usb sound card and different cable with no luck. I run the command below with no luck, only get audio through the left speaker. speaker-test -t wav -c 2 Any ideas how to fix this?

Device rk3399 I have installed Waydroid and installed an application to watch videos But some of the videos were found to have issues (Does the playback speed increase like frame skipping? The sound has also changed) Because I don't know if it's a GPU issue with the firmware itself or if it's caused by not using Waydroid,So I want to know how to test whether GPU is used in Linux Did the installed Waydroid use GPU

Hi, First post here. I'm fairly new with Armbian. I have a LibreComputer Le Potato that I want to use for Home Assistant. To avoid all the hassle of setting up Home Assistant with docker, I used the Armbian imager to install the Armbian 26.2.1 Home Assistant on an SD card. Once the SD card was flashed, I put it into the Le Potato board. The board starts up fine, asks for the root password, creates a new user and so on. Later on, the Preparing Home Assistant Supervised window appears. However, after the first round to 100% I get a "RTNETLINK answers: Invalid argument" on the screen. The preparation goes on and on, moving the progress bar ove…

Hi there, Basically I am trying to change the wireless regulatory power for the Opi PC. I follow the instruction like in this link and it worked in Rpi: http://askubuntu.com/questions/597546/iwconfig-wlan0-txpower-30mw-not-working I modified the country of BO to 30 from db.txt so I get 30dbm signal for testing purpose. When I have done all the proceedure in Opi PC and reboot I try to type " iw reg set BO" ,nothing happened - it still stayed at 00 which is the default country set. It also appears that when I type "iwconfig wlan0 channel 13" it then changed the country to China. And by then I can change the country BO by typing the "iw reg set BO" again. When…

Hello, guys. I have a trouble with touch screen on OPi PC 2 (Connected via USB). Touch detected like Bus 006 Device 002: ID 0eef:0005 D-WAV Scientific Co., Ltd Tried to add `modprobe ads7846` and `modprobe hid-multitouch`. Without results. But on last command returned an error modprobe: FATAL: Module hid-multitouch not found in directory /lib/modules/4.11.1-sun50iw2 Can u help me? Thanks.

Hi Guys, I buy me in LCD-Display (BL035-RGB). This will be connect to my Banana PRO. All this I do, how it is described on this page "here". After change the config, add the script.bin and reboot, the display do nothing. It all the time black. It come no flash or something. My question is, what I have to change on my Banana Pro? I have install ARMBINA 5.31 (4.11.6-sunxi). One thing. How I can test the LCD-Display for conection? Can I send commandos to the Display? thanks for YOU help.

Unable to boot Cubieboard 1 after install armbain on sata hdd. I use Boot from nand - system on sata

Hi guys, I am trying to connect my orangePi internet with ethernet cable but nothing works I tried every way but still I have no internet So please help me. Here are the solutions I tried: 1) I open the share settings from Wifi properties and connect the pi to Pc with normal ethernet cable 2)Bridge the ethernet and wifi 3) installed samba in orange pi and I have nothing OrangePi's ethernet leds are running but no internet I have one last solution , buying a wifi module and connect to wifi with it but I have no idea about wifi modules. Sorry for my english.

I had some answers on it.. there is a few comments at my question.. but no way to fix/reset it.. i tried to chroot on a kde linux and another time on a emmabuntu linux.. result: didnt work.. can someone post to me some an answer!?.. thx alott..

Using a 256G emmc and the server image v6.12 my Odroid N2+ doesn't boot. Here is the log. The Homeassistant image works. Would be nice to understand why it doesn't boot. <00><00><00>G12B:BL:6e7c85:2a3b91;FEAT:E0F83180:402000;POC:F;RCY:0;EMMC:0;READ:0;0. bl2_stage_init 0x01 bl2_stage_init 0x81 hw id: 0x0000 - pwm id 0x01 bl2_stage_init 0xc1 bl2_stage_init 0x02 L0:00000000 L1:00000703 L2:0000c067 L3:14000020 B2:00402000 B1:e0f83180 TE: 196470 BL2 Built : 06:17:13, Jun 28 2019. g12b gf0505d7-dirty - qi.duan@droid13 Board ID = 5 Set A53 clk to 24M Set A73 clk to 24M Set clk81 to 24M A53 clk: 1200 MHz A73 clk: 1200 MHz CL…

I am not able to boot from armbian. First I downloaded image from (https://www.armbian.com/orange-pi-zero-2w/) later on I flashed the image with usbimager, then since this didn't work I did with balena etcher, (all those in linux). Balena etcher crashes at verification so then I did with my windows machine, first with usbimager and since it wasn't working I decided to decompress the .xz and do it with "rufus" Here i attach the images and as you guys can see it says "failed to mount /dev/mtdblock4". That terminal is pretty much useless, I can't even do reboot or poweroff. I just need armbia…

After my last update on my radxa5-ITX, apart from the name changes of the NIC (related?), I remarked that I could not cryptroot-unlock the root partition because of dm_mod apparently missing from initramfs. To give some context, this is how I set things up some while ago and things went pretty smooth until recently. Too bad armbian does not keep the previous kernel (though I get the reason why). Inspecting the boot partition, cat config-6.1.115-vendor-rk35xx | grep DM_CRYPT CONFIG_DM_CRYPT=m the kernel seems to have been compiled with the proper option and lsinitramfs initrd.img-6.1.115-vendor-rk35xx | grep 'usr.*cryptsetup' usr/lib/aarch64-l…

Are there any plans to create an Armbian image for the Radxa Cubie A7S? It's a really cute single-board computer with a powerful Allwinner A733 SoC.

Hi all. After installation of transmission-daemon I got two issues. First one is "UDP Failed to set receive/send buffer". I did fix it by adding next two lines to /etc/sysctl.conf net.core.rmem_max = 16777216 net.core.wmem_max = 4194304 Second one is that RPC does not start on boot but only after manual restart of service after boot. I believe it's caused because transmission starts before network goes online. I tried to fix it by adding into /lib/systemd/system/transmission-daemon.service [unit] ... Wants=network-online.target After=network-online.target But it does not help. I did fix it by adding next two lines to /etc/rc.l…

Hey, First: Thanks to everybody making this work. I installed armbian on a beelink x2 TV Box with the old wifi Chip, we had two of them and the Android Rom just stopped working, well it worked but the Youtube App and such Things didnt. Im trying to reuse them as little Desktop Machines with armbian. For its Hardware it runs pretty good but there is one Problem. I need a new build of smTube, the Version i get via apt-get is to old. The box plays the Videos via Kodi or with a direct Link in smPlayer well but in FireFox it decodes it over the CPU i think and then it has Problems. I also tried to install a new smTube arm deb package with Gdebi but there are some depenc…

Under the Download web page all the manufacturers ("Maker") are listed, but the company "Banana" is missing in that list.

There was a critical vulnerability found in Realtek wireless drivers: The vulnerability has been assigned CVE-2019-17666 and a patch proposed: https://lkml.org/lkml/2019/10/16/1226 I would like to get some statement if Armbian users are affected and if yes when is the patch going to be released Thanks

Hi, I'm having encountering the above errors, it is persistent with every boot. It occured both on buster and on buster-minimal. Note that specifically the micrel kmod fails verification, but because it shares a signature with many (all?) kmods, I assume it applies for them all. See output of dmesg below. Edit: Wanted to say - I can't tell if these are 2 distinct errors, so I posted both together Thanks [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.21-sunxi (root@hirsute) (arm-linux-gnueabihf-gcc (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) 8.3.0, GNU ld (GN…

I've been getting these errors when I run apt update / apt upgrade on an OrangePi One Plus: Err:13 https://apt.armbian.com/apt bullseye Release Redirection from https to 'http://imola.armbian.com/apt/apt/dists/bullseye/Release' is forbidden [IP: 173.45.128.12 443] if I edit /etc/apt/sources.list.d/armbian.list to be https://imola... it works fine. EDIT: armbian.list originally looked like this: deb https://apt.armbian.com/ bullseye main bullseye-utils bullseye-desktop and I changed it to look like this: deb https://imola.armbian.com/apt bullseye main bull…

I'm trying to build Armbian desktop image in 64-bit uBuntu and it does not complete. When I build the server it completed nicely no problems. Displaying message: Adding APT Source deb [signed-by=/usr/share/keyrings/githubcli.gpg] http://cli.github.com/packages stable main Displaying message: Adding GPG Key /home/hydra/armbian/config/desktop/_all_distributions/appgroups/programming/sources/apt/githubcli.gpg Displaying message: Updating package list bullseye info Displaying message: Upgrading base packages Armbian info Displaying message: Installing the main packages for Armbian info Displaying message: Installing the desktop packages for Armbian info Disp…

Hi everyone! I'm software developer but have no (or little) clue about electronics & electricity, and would like to dive into the SBC world. I still don't have a goal other than have fun and support this community during my free time. I probably need to buy some devices (my budget is limited): A voltmeter A soldering station. Which filler material is more appopriate? An USB-to-TTL adapter to debug the serial output. Specs? Last but not least: an SBC! Which one is good but currently lacks support from this community? Something else? Thank you for your advices!

The long explanation is here Before: # dmesg ...... [ 9.606887] thermal_sys: Failed to find 'trips' node [ 9.606902] thermal_sys: Failed to find trip points for thermal-sensor id=1 [ 9.606923] sun8i-thermal 1c24c00.thermal-sensor: Failed to register sensor 1 (-EINVAL) [ 9.606938] sun8i-thermal: probe of 1c24c00.thermal-sensor failed with error -22 ...... My patch for sun8i-r40.dtsi. Yes, it's copy-paste with changing names of a cpu thermal trip point for a gpu thermal trip point. Now it's ok # ls /sys/devices/virtual/thermal/ cooling_device0 thermal_zone0 thermal_zone1 fix_gpu_thermal_zone_sun8i-r40_bananapi-m2u.patch

I have FriendlyElect CM3588 (RK3588 based) Nas kit which is lagging behind in terms of incorporating the latest NPU driver (the current is 0.9.3) in their firmwares. Thier repository contains Ubuntu / Debian with Kernels 6.1.x As far as I know the latest RKNPU version is 0.9.6. and as I understand there is no OS on Armian tailored for CM3588. What is best way to get the lastest driver?

Hello I need to increase the size of the CMA on my armbian set up. But I've not found a way to do it. Is there a kernel command line option I need to pass to increase the CMA size, or is this done in the kernel configuration before building? Thanks in advance.

Hi, I want to patch the kernel with the preempt-rt patches from the repository but their are corrupt Who needs this patch? I think the real time kernel is very useful for many projects.

Hello, I would like to recover my Armbian root file system on a second sd card. On the second sd card there is a slightly older Armbian version installed. Unfortunately my efforts ended up in a boot loop with the second card. Here is what I did: backup current Armbian tar czpf ~/tmp/backupArm.tgz --exclude=dev/* --exclude=proc/* --exclude=run/* --exclude=tmp/* --exclude=mnt/* . restore backup on second card tar xvzf ~/tmp/backupArm.tgz Both cards use MBR partition style. Partition starts at sector 2048. Here are my SD cards details: current (source) fdisk -l /dev/sde Disk /dev/s…

Hi, I'm first time to lean that " Orange Pi" and Debian Linux system, I have two questions. 1. How to change that the scree picture or character after typing user name/password. 2. How to starting my own program after system boot-up finished. My program is connect to copy machine it will catch that using status and send back to server. Thanks

Hello i need some help. I want to access my OPI+2E remotely over the internet. I tried to use TeamViewer couldn't make it to run on armbian i followed all the instructions posted here on forum but it didn't help. I don't have static ip any other way to do it? Kindly, help me.

I have orange pi one zero. I buy extended Nas card for orange pi zero. After install extended board, i can't logging in system. Root or user password not accept system) Try logging with UART and SSH. Try copy new password in shadow on my PC. But system not accept any password. Maybe system himself change password after changing system or some problem with bash? p.s. I have Bpi M2p too and last month was the same situation. But console not accepted any login and after enter "root"....again asked to enter login. I rewrite new Armbian and return to work.

There's a cheap M2 SSD, for example for sale here, but it would be a bad idea to use it in any ARM board with an M2 drive slot. I have one of these M2 drives in my laptop, and I learned the hard way how slow it will get within 1 year's use, like 30MB/sec read, 8.5 MB/sec write! Over time, this drive will gradually go slower and slower and slower, until you figure out you need a firmware upgrade. Then you'll need to use the closed-source firmware-upgrading CLI utility that Micron publishes. There is a version for linux, but it's AMD64 only. You might think you can put the M2 drive in a USB-3.0 enclosure, then firmware upgrade it in that enclosure…

Mỗi Dự án của tập đoàn Vingroup luôn tạo sự khác biệt, độc đáo, mới lạ, để lại dấu ấn riêng cho người dùng. Là tập đoàn đi đầu trong việc vun đắp các tỉnh thành kiểu mới, bắt kịp xu thế thời đại, kết hợp nét đẹp đương đại và truyền thống, mỗi thành tựu mà Vingroup với về là niềm tự hào của người Việt. Vinhomes Smart City là khu đô thị sinh thái khép tín tiếp theo được Vingroup giới thiệu tới thị phần trong năm 2020 sẽ quy tụ đa số những nhân thể ích đẳng cấp nổi trội chuyên dụng cho phần lớn các nhu cầu của mọi thành viên trong gia đình như trông nom và rèn luyện sức khỏe, vui chơi, tìm tậu, tiêu khiển và hệ thống giáo dục đương đại. 1 số tiện ích dự kiến của …

I would like to add new resolution with this patch: https://github.com/FireflyTeam/armbian-build/blob/master/patch/kernel/sun8i-default/0026-h3-hdmi-additional-mode-800x480p-from-lobodis-initia.patch But I need this parameter means: in drivers/video/sunxi/disp2/hdmi/aw/hdmi_bsp_sun8iw7.c vic dclk, int, mx, vst, my, mhbw, vfp, mhfp, +x, hbw, hfp, hst, +y, vbw, h v h_pol v_pol in drivers/video/sunxi/disp2/hdmi/aw/hdmi_core.c PCLK x, y, HT, HBP, HFP, HS, VT, VBP ,VFP , VS, h_pol, v_pol, int I know pclk: pixel clock x: 1024 y:600 …

Hello! First post so apologies for any naivete. I have a USB wifi adapter connected to my la frite (it was the only distro that supported it out the box so thank you). On each boot it seems like the USB is getting a different device address and therefore I have to open nmtui and connect to my wifi all over again, to the point where I have 10+ stored connections to the same wifi in my network managers saved connections. At first I thought I could solve the problem by reversing the Persistent Interface Names settings on boot so that it would be wlan0 and I could automate the connection on startup but that hasn't worked for me either. I've run out of ideas a…

I guess my application is IOT - I am getting data via USB and SPI, report status via GPIO LEDs and upload data to the internet. I am enjoying raspberrypi 3B but it's huge and relatively expensive. I am trying to return Orange Pi 2G IOT since it's a disaster. Looks like Orange Pi Zero for a bit under $20 would not be a disaster? Are there other boards to consider if I care about physical size and price?

Armbianmonitor -u After an attempt to use wifi on cubietruck on Buster server 20.05.2 (upgraded from Jessie) the board experiences random freezes and I need to power-cycle the board to bring it back. I am now on Buster 20.08.02 after upgrade without using wifi (blacklisted as on the original image) I am trying to pinpoint the source of the freeze (I don't want a fresh install) but due to zram logging, I can't seem to be able to find anything useful in the logs. Can someone suggest any other method to debug my issue or how to temporarily disable zram logging? Edit: I used systemctrl to stop zram and zram logging temporarily

Hello people, Half a year ago I flashed Armbian to to Mekotronics R58 plastic box, which was then an unofficial version. It's been on the shelf a while. Now I see new Armbian versions for download. I plugged in my device and did an update/upgrade. See Neofetch result below. My question is: is there any reason to completely flash the new version? Or am I already fine? It seems kernal versions are the same! Everything works fine and looks awesome including RealVNC for which I had some work to do. Therefore I am a bit reluctant to ditch the current version. Couple of minor issues I have are can't get Samba working and boot from SSD. Bas …

Hello everyone, I purchased a single board computer and plan to use Armbian for my projects.; Could anyone suggest the best version of Armbian for beginners?? I want to ensure I have a stable and user friendly experience. I am curious about the initial setup process. Are there specific configurations or settings that I should focus on during installation to optimize performance? Also, I am interested in knowing about the community support available. Are there resources, forums or tutorials that you would suggest for newcomers to learn more about using Armbian effectively? Also i have check this; https://forum.armbian.com/topic/27407-complete-headle…

Hi everybody With freshly installed armbian (commit id: d9fb61be0) I created a new uboot config file: ./compile.sh uboot-config BOARD=orangepizeroplus BRANCH=current SHARE_LOG=yes This creates the file: ./output/defconfig-uboot-orangepizeroplus-current But the command: ./compile.sh uboot BOARD=orangepizeroplus BRANCH=current SHARE_LOG=yes does not compile uboot, it just touches ./output/debs/linux-u-boot-orangepizeroplus-current_26.11.0-trunk_arm64__2026.07-*.deb file. Do I miss something? Do I have to copy the file ./output/defconfig-uboot-orangepizeroplus-current to a place in ./userpatches? …

Do you guys think/know if this would work on a Orange pi. https://github.com/riptidewave93/RFLED-Server It seems to be written in golang, I don't know how is it with the gpio's if stuff is written in golang. Well here its UART stuff actually but you get the picture..

First things first. I am enjoying armbian so thanks all for it and well first post as well so Hi and stuff. Ok I likely dont know what I am talking about and I have been able to verify SMP working but something is bothering me. On every multicore system I have ever used I always see the cores split out into separate processors in cpuinfo like this: processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 42 model name : Intel(R) Core(TM) i5-2540M CPU @ 2.60GHz stepping : 7 microcode : 0x29 cpu MHz : 894.257 cache size : 3072 KB physical id : 0 siblings : 4 core id : 0 cpu cores : 2 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level :…

I just did a Python 3.6.4 build using all 4 cores, and it handled beautifully. You can see where it switches from a single core for the ./configure into all for cores for the make -j4 altinstall Time CPU load %cpu %sys %usr %nice %io %irq CPU C.St. 21:41:30: 1200MHz 1.00 26% 8% 17% 0% 0% 0% 57.2°C 0/8 21:41:35: 1200MHz 1.24 27% 9% 17% 0% 0% 0% 56.4°C 0/8 21:41:40: 1200MHz 1.22 26% 8% 17% 0% 0% 0% 57.1°C 0/8 21:41:45: 1200MHz 1.21 26% 8% 17% 0% 0% 0% 57.2°C 0/8 21:41:50: 1200MHz 1.27 26% 8% 18% 0% 0% 0% 57.4°C 0/8 21:41:55: 1200MHz 1.25 26% 9% 17% 0% 0% 0% 57.6°C 0/8 21:42:00: …

Dear All, today my Opi PC stoppped responding. But I think it is not totally "dead". From other machine I did: root@PKSERVER:~# ssh -vvv pkbackup OpenSSH_6.7p1 Debian-5+deb8u4, OpenSSL 1.0.1t 3 May 2016 debug1: Reading configuration data /etc/ssh/ssh_config debug3: checking match for 'exec "/etc/ssh/pkdata.sh %n"' host pkbackup debug1: Executing command: '/etc/ssh/pkdata.sh pkbackup' debug1: permanently_drop_suid: 0 debug3: command returned status 1 debug1: /etc/ssh/ssh_config line 18: no match 'exec "/etc/ssh/pkdata.sh pkbackup"' debug3: match not found debug1: /etc/ssh/ssh_config line 21: Applying options for * debug2: ssh_co…

Hey there, uploading armbianmonitor failed, due to the connection issues, so i pasted it somwhere else: https://nopaste.xyz/?40aa3fcbb5834d1c#a9goEaQrtfCzF+MAAhWDb4+Gbfq6UMa2smyGL+ShbME= password is armbian My problem is, that there is no working outgoing IPv4 Traffic, i cant even ping a v4 adress. But on adresses, that get a AAA-Response from DNS it works fine. Had pihole installed, removed it for testing but this didn't make an difference. No firewall in use, iptables is empty at the moment. Every v4-Request ends up in a !N or No route to Host. While using pihole, i saw that the request went throug to pihole and was forwarded …

Network connection terminates Hello everyone I use RockPro64 4GB with> Armbian_19.11.3_Rockpro64_buster_current_5.3.11_desktop.img RDP + NCP + OMV5 is installed, all about> armbian-config> software> softy-3rd_party_applications_installer. I installed VNC with> apt-get install tightvncserver. Right from the start I had problems establishing a stable connection to the OMV GUI via browser Firefox / Chrome or to the VNC. Approximately after 2 / 3min the "session" was always interrupted and I had to reconnect VNC or reload Firefox. The solution was that I added a new interface in the OMV GUI via> Network> Interfa…

SMART AM40 iQ Appliance P/N: 1031572 Model: UGK-AM40-EDU | EWY1-AM40-EDU | EWY2-AM40-EDU Processor RK3399, Dual-core A72+Quad-core A53, 64 bits, 2GHz Memory 4 GB DDR3L SDRAM Storage 32 GB eMMC 5.1 Wireless technology Bluetooth 4.1 802.11A/B/G/N/Ac Capture options Establish a Bluetooth wireless connection with a supported mobile device Connectors HDMI 1.4 (1920 × 1080) output for external monitor USB 3.0 Type-A (×2) RJ45 Gigabit Ethernet --Update-- For device tear-down and technical sheets included in package - SEE SECOND POST …

Greetings, I'm attempting to apply a custom patch during the build process for a bananapi-m2-zero. (specifically, DTS changes) I went into the kernel source, and created a diff, and put it in the user customized patches directory. Unfortunately, the patch failed. So, I dug into it, and discovered the source changes because of patches in the armbian patches/ directory. So, instead I started the build, let these patches apply,, and aborted the build. Then I created the diff again. Sadly, the patch is still being rejected. Now, I might be able to fight with this, and make it work. But the next time I pull a new update it could be broken a…

Hello! I follow instruction "Add names of overlays you want to activate to overlays= line in /boot/armbianEnv.txt" I try to find /boot/armbianEnv.txt but nothing. I see Build tools overview from https://github.com/armbian/build/blob/fcb8b6f195bbb76c83c612c425fdf08cfd48c68b/README.md And nothing about /boot/armbianEnv.txt May be documentation talking about build/config/bootenvrockchip.txt and build/config/zynq.txt and others txt files in build/config/ ? It looks like /boot/armbianEnv.txt is file on microSD after I burn armbian image on it. But reading docs I don't understand nothing about build/config/bootenv/rockchip.txt

Hi, I am tring to build Armbian to Orangepi pc but there is no specific conf file for orange pi pc in its menuconfig? Can you pls help me to build it? Umit

does anyone know of a version of armbian that would work on a samsung galaxy book go with a snapdragon 7c gen2? i traid the generic version and it booted to the grub, and then it restarted like all other distros i've tried. i can not find a distro to boot on this dang thing. anyone have any ideas on what to do or try? i've hit a dead end i gotta dig deeper to figure something out, so any thoughts on this would be helpful .. thanks in advance

Glad to say creating virtual machine and getting Armbian build environment and running ./compile.sh was easy and successful for bananapim1plus / 6.1 kernel / jammy. Created SD card and booted and is running fine. Added DT overlay to enable spidev and got /dev/spidev0.0 as expected. Got new version of cross compiler to build code I formerly ran on fedora image and the SPI driver behaves differently. It pulses CS low for every transfer instead of optionally staying low for multiple transfers based on "cs_change" field in each transfer message. Found kernel source in build/cache/sources/linux-kernel-worktree/6.1__sunxi__armhf/drivers/spi, and tried editing there to begi…