Beginners

Hello to everyone! I'm trying to solve the issue which is currently being discussed here and I've been forced to revert back to the ancient version in the title. The problem is that along with my OPi PC I use a cheap wireless adapter based on the MT7601. Here, I've found out that the support for these cards had been merged to upstream since 4.2 kernel versions indeed with Armbian Focal 5.10.4-sunxi it worked out of the box like a charm. Unfortunately, it isn't the case with the version I'm currently on, this adding another massive headache! I've found this really interesting thread where it is discussed how to add support for the MT7601. Everything went fine apart …

I downloaded the "Armbian 22.11 Jammy" image today and it won't boot, the red light won't come on most of the time (it does occasionally). I will no longer report the situation of my SD-card, power supply, and burning tools. In short, they are all fine, and I am a person who often burns Armbian' images, so I can say that I am very experienced. After repeated attempts, I downloaded "Orangepizero2_3.0.6_ubuntu_jammy_server_linux5.16.17" from the OPI official website, made a boot disk with the same method, and it can boot normally... OPI Hardware Version: V1.5 SD-Card: Sandisk Extreme 64G V2, buy from official store Power supply：3A adaptor, from …

Device rk3399 I have installed Waydroid and installed an application to watch videos But some of the videos were found to have issues (Does the playback speed increase like frame skipping? The sound has also changed) Because I don't know if it's a GPU issue with the firmware itself or if it's caused by not using Waydroid,So I want to know how to test whether GPU is used in Linux Did the installed Waydroid use GPU

Hi This issue is produced on both flavors of Linux for the orange pi zero i.e. Debian and Ubuntu. I am trying to login to pi zero using the serial terminal. First time it asks me to change the password, which I changed. Then using that changed password I tried to login into it. However, whenever I enter the password in it. it restarts. I even used the external high power phone charger to test this issue but in both cases result was same. Any solution to this problem?

I cannot get the console connection to work I've used Putty on Windows but there seems to be no COM3 starting up?

Hi to all, My box was running in the same issue. So have I've had a look into the logs. In my case it was the knowing Bug https://bugs.launchpad.net/ubuntu/+source/lirc/+bug/1768291 > lirc is flooding the syslog with two lines each second [date&time] flupp lircd[1323]: lircd-0.10.0[1323]: Error: Cannot glob /sys/class/rc/rc0/input[0-9]*/event[0-9]* My solution was to uninstall lirc. Have nice day deBugger @moderator the thread https://forum.armbian.com/topic/6229-ramlog-full-no-space-left-on-device/ was closed feel free to join.

Hello I am new to Nanopi m1 plus development board. I followed the instruction as on friendlyarm's wiki page. I loaded the image from my Ubuntu OS and connected my device to the pc. The blue led was blinking normally. I used Putty to view the logs. While booting it is showing: resize2fs 1.42.12 (29-Aug-2014) resize2fs: Bad magic number in super-block while trying to open /dev/mmcblk0p2 Couldn't find valid filesystem superblock. resize2fs exited with status code 1 done. mount: mounting /dev/mmcblk0p2 on /root failed: Invalid argument done. Target filesystem doesn't have requested /sbin/init. Begin: Running /scripts/local-bottom ... done. Begi…

Test version 20221216-legacy for rk3399 (Station P1). The kernel 5.10.11 is used instead of 4.4. Some of the functions are not working yet. Switching to this version will get rid of a very outdated version of the BSP 4.4 kernel.

Hallo liebe Community, ich versuche, da es kein aktuelles jammy release für meinen M1 gibt, eines mit Ubuntu zu erstellen. So wie es in der Dokumentation beschrieben ist. Allerdings kommt immer wieder ein abbruch: ERROR in function install_deb_chroot Und dann wird der Prozess terminiert. Warum funktioniert das denn nicht?

Hi, I can't record audio from I2S interface on Lime2 (A20) Ubuntu_trusty_3.4.112. For record the sample 60 sec. (44.1K 16bit) I used this command: arecord -D hw:1,0 -t wav -c 2 -f S16_LE -r 44100 -d 60 test.wav File is success created and recorded, but absolutely nothing sounds. Why I can't write sound?

After upgrading the system, my WiFi cannot be used. After inspection, it was found that there was no driver (brcmfmac4330-sdio.oranth, tx3 mini. bin). Where can I download it or how can I fix this error?

Trying to update Armbian_community_25.8.0-trunk.38_Radxa-zero3_bookworm_vendor_6.1.115_minimal got a problem with beta.armbian.com's certificate: Err :6 https://beta.armbian.com bookworm InRelease Certificate verification failed: The certificate is NOT trusted. The certificate chain uses expired certificate. Content of /etc/apt/sources.list.d/armbian.sources Types: deb URIs: https://beta.armbian.com Suites: bookworm Components: main bookworm-utils bookworm-desktop Signed-By: /usr/share/keyrings/armbian.gpg Something to do on my side? Denis

Hi, I am trying to optimize torrent download speeds on SBC. and I have the RPI4-2GB board. I get somewhat similar results for the Odroid HC1. I only download 1 torrent at a time, and I dont upload. So very simple requirements. On a 1000/1000Mbit connection. Samsung 4TB 870QVO HDD - UAS enabled and tested with good controller. Same file downloaded multiple times. So the external factors such as the ISP or the Storage is for sure NOT the bottleneck here. Transmission - 21MB/s ~ 168Mbit/s qBittorrent - 34,8MB/s ~ 278,4 Mbit/s ruTorrent - 29,3MB/s ~ 234,4 Mbit/s Laptop - 118,7MB/s ~ 950 Mbit/s I have identified that transmission bottlen…

This message is on-topic, but for an unknown reason, it is not possible for me to create a message in Help wanted. So I post here. I have used Armbian for two years, I think, on several devices, and I have given some money to support it. Thanks for the job. I recently upgraded to the last version with Debian 11. Everything fine but one point which is probably not a bug, that's why I don't post in "bugs". I use Unbound which is the heart of my soft. And I use a python script which is loaded by Unbound. Until now, there was no problem. With the last version, I ran in several read problems. The first reason I found is apparmor, which prevented the script to o…

Hello everyone, First timer here. I enabled the wlan0 interface on my Orange Pi zero 2w and am able to connect to the internet. However, I am not able to connect to it via SSH or even ping it, (cannot resolve host). I'm using the minimal image available here: https://www.armbian.com/orange-pi-zero-2w/ I followed the docs to configure wifi as pointed out here: https://docs.armbian.com/User-Guide_Networking/#connecting-to-wifi-network Currently I'm stuck on how to debug it further. I tried to ping other devices from within the orange pi and it works without any issues. Any advice is very much appreciated

pine64 products have sloppy DC connectors. This connector simply detaches from the motherboard. I use in production pine64 pine64-lts pineH64 and rock64. As a result of switching on and off the dc connector, in each case it has peeled off and does not hold power. I've attached the DC connector with glue but that's not what the factory mount. The low price now goes sideways. workmanship worse than nonopi.

If you want to get ahead of the curve a little I've been testing libgpiod master with User Space IO. This version includes Python bindings, so I'm no longer generating CFFI bindings for this library. I've converted all the example code to use the new bindings. User Space IO is Python 3 and Java 8 bindings for Linux user space GPIO, SPI, I2C, PWM and Serial interfaces. User Space IO is a consistent API for C, Python 3 and most JVM languages. No more hacked up RPi.GPIO and WiringPi for each SBC model.

I'm trying to use an Orange Pi Pc Plus v1.1. The disk images for it provided by Orange Pi are worth nothing, having repositories that do not work. As an alternative I've been looking at Armbian, and decided to try the images supplied here: https://www.armbian.com/orange-pi-pc-plus/ . I had a problem with both: -The Ubuntu image always reboot as soon as the gui loads. I don't think it power related, since I'm using a 3A power supply and that's more than what is recommended. -The Debian image doesn't allow me to connect to the internet. I don't have the option to use a cable and the WiFi network I have access to uses PEAP, and I found no way to configure …

My 32GB SD Card have problems and i have buy new one. I have use Acronis True Image 2015 to clone the one Card to the other but the new one does not boot. Why????? Every normal Computer does cloning work with new Harddrive and now that Problem!

For e.g. SD card removals I power down the Nano with shutdown -P. To restart I usually unplug and plug in again USB power. To avoid the pluging, is there a possiblility to add/solder a reset/restart button to the NanoPi Neo board?

I have the same problem. Using Lubuntu 14.04- 0.9.1 img for Orange pi lite. bin2fex in sunxi tools gave me "malformed data" error. using the windows bin2fex gave me "unrecognized GPIO port #12". Since this bin2fex is so critical in setting display, audio, resolution, etc. This bug made my ARM experience very bad. I understand and appreciate all the efforts in the linux community though.

With the Orange Pi Zero 2 (Bullseye), when in Armbian-config I install desktop with browser...it seems working but when you enable the desktop it finished by a kill() in the terminal. You can solve the issue by apt-get install tightdm.after and not before. You will get the desktop for the user and not root. Grey Background with the pinguin. If you install Desktop in Bullseye with Orange Pi One Plus or Orange Pi Zero, no issue. You have the new Debian Desktop with a Background dark blue. Regards F1ATB.fr

I am trying to stream a video using NanoPi M1 Plus device from a URL using mplayer https://someurl.com/video.mp4 But it throws an error No stream found to handle url https://someurl.com/video.mp4 What is the issue?

Can I power orange pi zero directly from 0 & 5V pins?

Duplicated in another thread...Never mind.

...as title. I've installed ispConfig using Armbian-Config, but now I want to remove it. How to do it? Googling I've see that there is a unistall.php or /root/ispconfig/uninstall script that do that, but there is no trace in armbian.

EDIT: I tried to plug it directly in router and speed is OK now. Weird, but it's fine now. Please close this topic. Hello, I just bought Orange Pi 3 LTS to set it up as small off-site backup using OMV and USB HDD. I installed Armbian_23.02.2_Orangepi3-lts_bullseye_current_5.15.93.img on eMMC and installed OMV using armbian-config. I noticed SMB and FTP speeds are slow (around 90 Mbps) so I installed iperf to test it properly and speed is capped on 94 Mbps. I have gigabit switch and interface is connected with GE, if I plug the cable to other device, it works just fine. So there must be some issue on Orange Pi 3 LTS. I searched the internet and speed shoul…

I would like to add new resolution with this patch: https://github.com/FireflyTeam/armbian-build/blob/master/patch/kernel/sun8i-default/0026-h3-hdmi-additional-mode-800x480p-from-lobodis-initia.patch But I need this parameter means: in drivers/video/sunxi/disp2/hdmi/aw/hdmi_bsp_sun8iw7.c vic dclk, int, mx, vst, my, mhbw, vfp, mhfp, +x, hbw, hfp, hst, +y, vbw, h v h_pol v_pol in drivers/video/sunxi/disp2/hdmi/aw/hdmi_core.c PCLK x, y, HT, HBP, HFP, HS, VT, VBP ,VFP , VS, h_pol, v_pol, int I know pclk: pixel clock x: 1024 y:600 …

Hi! I am trying to set sudo chmod 777 /sys/class/leds/red_led/brightness It works, but after restart the system reverts my changes. I think there is some init file that changes it. Any tip?

Hi, I tried your Debian/minimal/IOT for NanoPi 5RC, it's great, I would like to use it. However the RTL8822CE driver only exposes wlan0 and there are no parameters to set, and I need two wlans. For reference there are two wlans available in the core debian image from FriendlyARM/ELEC. Best regards.

I have armbian installed on a 128gb sd card but it looks to be partitioned to about 2gb. How would I go about expanding the partition to include the rest of the 126gb? root@orangepizero2:~# df -h Filesystem Size Used Avail Use% Mounted on udev 422M 0 422M 0% /dev tmpfs 99M 1.9M 97M 2% /run /dev/mmcblk0p1 1.9G 1.7G 125M 94% / tmpfs 493M 0 493M 0% /dev/shm tmpfs 5.0M 0 5.0M 0% /run/lock tmpfs 493M 0 493M 0% /tmp /dev/zram1 47M 680K 43M 2% /var/log tmpfs 99M 0 99M 0% /run/user/0

I have a NanoPc T4 that I use to control an astronomical observatory. I successfully installed Focal on an SD card and it boots perfectly. But now I want to know how can I install Arabian onto the eMMC chip? I'm not a programmer, but can follow basic instructions. If this is possible, any help would be appreciated. Thanks!

Hi, how can I make bash script to control the fan below by temperature. https://www.aliexpress.com/item/32640103358.html I want to make it run only when CPU temp is more than 80°C

apt-get install python3-pandas Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: python3-pandas : Depends: python3-pandas-lib (>= 0.19.2-5.1) but it is not installable E: Unable to correct problems, you have held broken packages. Any suggestions?

Hi, I need to use the MPV option --record-file and notice that the repository 0.14 version doesn't have this. What's the best way to update to the latest version of MPV? I'm using MPV on legacy Armbian (Xenial) due to it's stable multimedia features on my H3 device. Thanks

Hi, I updated from legacy kernel to mainline and then from jessie to stretch. Armbianmonitor -u output is further below. So far, the main issue is that after rebooting the DNS server is set to 127.0.0.1 thus loosing internet connectivity. Here is the output of resolve.conf (with manual setting the nameserver after reboot ) and the static network config. I am struggling to find how the dns server is set after reboot. I would appreciate if anyone could point me to a HOW TO. Minor issues: I can see only one cpu with htop, the ip address is not recognized at the ssh login screen, the opi pc is recognized as opi lite at the ssh login screen …

Wondering if anyone has an operating mPCIE Kingston SSD working like this one. This one isn't being recognised.

hi, i want to generate an armbian version for olinuxino micro A10S card this card is not in the list proposed by the compile.sh tool is there a howto , which explain the procedure best regard

I installed both earlier and the latest Armbian stretch service versions. Couldn't boot from the micro SD cards. Tried several different micro SD cards too. Nothing showed through HDMI. The red LED on board was double blinking. The board can boot from all three official images.

Hi, I'm trying to generate a U-Boot for my OrangePi Plus board (H3). I'm using the Denx 2021.10 release and have tried the standard defconfig for this board and also variations of this config. Starting the kernel is fine but the kernel crashes/hangs when starting if I'm using HYP (nonsec) mode. Starting in sec mode works but this only enables one of the four CPU cores. The kernel crash/hang occurs while executing "udevadm trigger --action=add" but I can't determine exactly what is being enabled when the error occurs. Trying different kernels (including the Armbian 5.10 version) show no difference. The Armbian U-Boot (2021-10 dated August 2…

Device: OrangePi PC Plus OS: Debian 9.3 (stretch) armv71 In my sd card, i separated Debian partition into 2: root and home. When i use nand-sata-install, it only transfers root to emmc. How do i modify nand-sata-install so that it copies both partition into emmc? sdcard storage capacity = 8GB sdcard lsblk: NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT mmcblk0 179:0 0 7.4G 0 disk ├─mmcblk0p1 179:1 0 4G 0 part / └─mmcblk0p2 179:2 0 3.4G 0 part /home OrangePi emmc storage capacity = 8GB emmc lsblk (after run nand-sata-install): NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT …

Hi, I have sort of a strange problem. 1.) lxc buster container built on armbian rockpro64 compiled OpenCPN built and installed the deb package without any issues. 2.) tried to install the package and faced wxWidget issues though I added the wxWidgets ppa and did a apt install *wxwidgets* BUT got this error: ----------------------------------- root@rockpro64:~/postinstall/opencpn/OpenCPN/build# cmake ../ -- cmake version: 3.13.4 -- *** Build Architecture is arm64 -- Setting C++11 standard via cmake standard mechanism -- Default compiler options: -- CMAKE_CXX_FLAGS: -- CMAKE_CXX_FLAGS_DEBUG: -g …

Hello. I use Retrorange Pi on Orange pi pc+ and the kernel includes a uinput module for implementing console utility management from the gamepad. Unfortunately, in this 5.3.0-dev-rc8 core, the CPU temperature information does not work. I switched kernel to 5.4.20-current via armbian-config. In this kernel, the cpu temp readings work, but unfortunately, there is no uinput in the modules. Can I somehow build this module separately for 5.4.20-current without recompiling the entire kernel? Or is it possible for respected developers to re-enable the module in future kernel releases? With best regards, Sergey

I have installed syslog-ng which removes rsyslog, now I am trying to filter using journald as docker is set to log to journald. If I create docker.conf in /etc/syslog-ng/conf.d with: filter f_dockerd {"${.journald._COMM}" eq "dockerd"}; destination d_docker { file("/var/log/docker.log"); }; log { source(s_src); filter(f_dockerd); destination(d_docker); }; Everything is logged go to docker.log, not just docker logs. The journal source is already setup with system() I think as if I try to add a journald source I get the error there can only be one.

Hi there, I am a newbie. Just built my first kerne;/uboot for my RockPi S board. I was wondering a few things : * Are the kernel sources online ? For example : linux-source-5.9.16-rockchip64.tar.xz * If I want to add a devicetree overlay and driver code, what is the best way to do that ? Should I ammend the kernel ? Should I create an out of kernel package ? thanks Matt

Hi all, Is there any working way to enable detailed logs from uboot? I am using fresh main branch (latest commit is 4648add1450c1b26bb29bf412ef054b0e978947d) . I have created following config inside userpatches/config-test.conf.sh file BOARD="orangepizero" BRANCH="current" RELEASE="jammy" BUILD_MINIMAL="yes" PREFER_DOCKER="yes" DOCKER_ARMBIAN_BASE_IMAGE="ubuntu:jammy" BOOTDELAY=2 UBOOT_DEBUGGING="yes" My command to build image is ./compile test. As I understand from source code UBOOT_DEBUGGING variable should enable such detailed uboot logs, but it seems like build framework ignored this option, I did not get detailed logs from uboot, also build logs do not conta…

I have a project with "Orange PI PC PLUS" and a Realtek 8153B usb-ethernet adapter. My big problem is that the adapter lights do not come on, even if the rest is working. On windows systems the activity light of the adapter lights up, but in linux no (I tested on armbian 5.60 and ubuntu 18.04). I've successfully installed the linux driver from realtek's website, but the light still does not light up. Module r8152 installed and used for the device.

hello, how to redirect audio output on jack instead of hdmi? cannot find any configuration... thanks a lot

I get this error on https://fi.mirror.armbian.de/dl/orangepi5-plus/archive/Armbian_24.5.3_Orangepi5-plus_bookworm_vendor_6.1.43_minimal.img.xz Jul 14 18:03:22 ek-arm kernel: ********************************************************** Jul 14 18:03:22 ek-arm kernel: ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** Jul 14 18:03:22 ek-arm kernel: ** ** Jul 14 18:03:22 ek-arm kernel: ** trace_printk() being used. Allocating extra memory. ** Jul 14 18:03:22 ek-arm kernel: ** ** Jul 14 18:03:22 ek-arm kernel: ** This means that this is a DEBUG kernel and …

Hi, Need to interface a multichannel codec to an OPiPC, having 8 channels out and 6 channels in. So trying to find any example of an overlay for H3 with TDM usage on simple-audio-card giving more than 2 channels in/out. Seen that the latest i2s driver for H3 (sun2i-i2s.c) does support TDM (DSP_A/DSP_B) but did not found any relevant overlay for H3 so far. Any help is appreciated. Christos

I'm trying to get mcp25xxfd device to work on OpenWRT. Currently I'm using ramips platform (Linux Kernel version is 4.14.180). I have the following configuration in one of my DTS files: osc: oscillator { compatible = "fixed-clock"; clock-frequency = <40000000>; }; spidev1 { compatible = "spi-gpio"; gpio-sck = <&gpio0 25 GPIO_ACTIVE_HIGH>; gpio-mosi = <&gpio0 26 GPIO_ACTIVE_HIGH>; gpio-miso = <&gpio0 27 GPIO_ACTIVE_HIGH>; cs-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; num-chipselects = <1>; …

I am experiencing frequent kernel panics with the RockPro64 board and assume it could be a power consumption issue with the SSD (PCIe NVMe M.2). I tested a variety of different SSDs, with the Cruzial P1 being the most reliable. Is it possible to manually throttle an SSD within Armbian, forcing it to consume less power? In my case, peak performance is not really important. This would allow me to further validate my thesis. Thanks in advance for any suggestions!

I'm running octoprint on my OPI PC and I'd like to buy some cheap usb camera for printing time lapses and visual inspection. FHD resolution is sufficient. As far as I can see, octoprint uses mjpg-streamer. Does someone use such camera? Is H3 capable of process FHD videos at 30fps?

I need connection MFRC522 and Mifare DESFire EV1 with python. Use code this project def __init__(self, dev='/dev/spidev1.0', spd=1000000): spi.openSPI(device=dev,speed=spd) GPIO.setmode(GPIO.BOARD) GPIO.setup(22, GPIO.OUT) GPIO.output(self.NRSTPD, 1) self.MFRC522_Init() def MFRC522_Init(self): GPIO.output(self.NRSTPD, 1) self.MFRC522_Reset(); self.Write_MFRC522(self.TModeReg, 0x8D) self.Write_MFRC522(self.TPrescalerReg, 0x3E) self.Write_MFRC522(self.TReloadRegL, 30) self.Write_MFRC522(self.TReloadRegH, 0) self.Write_MFRC522(self.TxAutoReg, 0x40) self.Write_MFRC522(self.ModeReg, 0x3D) self.AntennaOn() Code fo…

Hello everyone, I’m trying also to connect the RTC ds1307 in RockPi4C+, but it isn’t detecting by I2C. Informations: RTC ds1307 used: https://www.seeedstudio.com/Pi-RTC-DS1307.html Armbian OS version: 25.2 Kernel version: 6.12.10-current-rockchip64 i2c-7 enabled on armbian-config (> System > Kernel > SY210 > rockchip-rk3399-i2c7) When I run the command: sudo i2cdetect -y 7 shows the error Error: Could not open file /dev/i2c-7' or /dev/i2c/7’: No such file or directory When I run the command: sudo i2cdetect -l shows: i2c-0 i2c rk3x-i2c I2C adapter i2c-3 i2c rk3x-i2c I2C adapter Is someone can help t…

If you have ever compiled buildroot from Amlogic, please help me. I am trying to learn develop app on amlogic based device. First I was getting compile error on 64bit Ubuntu 16.04. Something like this. Even though there was a file, 'bash' couldn't find or run. /bin/bash: /root/buildroot/x86/xxxx-gcc: No such file or directory Thinking it's something to do with 64 bit OS, I switched to 32 bit Ubuntu 16.04. However after about 2 hours I'm getting following error. /bin/bash: /root/buildroot_openlinux/output/meson8b_m201/host/usr/gcc-arm-none-eabi-6-2017-q2-update/bin/arm-none-eabi-gcc: No such file or directory /bin/bash: /root/buil…

Hello. I have been struggling with creating a local build environment that will be guaranteed to work today, next month, next year etc. My hardware is Radxa-Zero and I want to run kernel 6.1.23. Currently I find that the build environment, in various ways, breaks the build over time. I've been chasing a stable build for kernels 6.1.23, 57, 58, 59. The build environment, by default, grabs the latest 6.1.y kernel, which is no good for me. My root FS and DTB are for 6.1.23 and I don't want to keep updating everything just because I need to make some kernel configuration changes. I have tried the BSPFREEZE and OFFLINE_WORK build options but t…

Hy guys i want to use a push button on my orange pi. if i press the button, the orange pi should run a script. i only use esp8266 with arduino tu create some interactive tools. does anybody know, how it works on the orange pi and which cheapy button you would prefer? i only want to run sh script, when the button will be press. thank you a lot!

I just installed Armbian Bionic (latest version) onto a Tinker Board (non-S). Connected to my home wireless network. Chromium works fine except when trying to access my Google Account. I get: All my other phones, iPads and PCs are fine. Please help! P.S. I don't think I can install Google Chrome either.

Due to systemd, Journal is going to replace all journals sooner or later, it's already one of the busiest journaling on the sytem. The logs are binary and can't be rotated like text logs, they are already compressed and can't be read by text editor, instead only by journalctl. Thus, in /usr/lib/armbian/armbian-ramlog , the directory /var/log/journal is excluded from standard log rotation and copying to HDD. Instead, it is copied once to /var/log.hdd/journal and a soft-link is created: /var/log/journal pointing to -> /var/log.hdd/journal . The RAM logging was introduced to spare the SD card, preventing many write actions that wear the SD card qui…

Hello I work on a project with Soc allwinner H6, I do tests with Orange Pi 3 y Orange Pi One Plus, everything works perfectly with armbian_20.08.1_ buster_current_5.8.5, Now I am testing with Rongpin RP-H6B witch Soc allwinner h6, but some things don't work for driver problems, someone knows if I can use armbian_20.08.1_ buster_current_5.8.5 on this board? my thanks in advance. Best regards Alyd

Goodmorning, I'm Tiziano from Italy. I would like to manage all the delicate functions of my reef aquarium through an Orange Pi Lite card. I saw that both the Armbian Buster program and the Armbian Focal program are available for my card, I kindly ask you to understand if there is a fundamental difference between the two and which. I have tried successfully in any case to install and run both programs on the microSD and to start the two programs. The card starts up and the whole procedure is performed correctly. The problem is that in the end I am only asked to choose the "default system command shell" between "bash" and "zsh", no option to start a desktop …

Hi, in the NetworkManager the Enable Mobile Broadband doesn't show up? lsusb shows the Huawei USB Stick as modem not as storage so this seems ok? what else can I check? I already tried 3 different sticks :-/ regards Meex

Hi, I just switched from an ancient ubuntu-rockchip install to armbian ubuntu 26.04 with the mainline kernel. I did a bit of an unorthodox installation, I wanted to install on an nvme drive, and instead of using a microSD and then copying the system with armbian-install, since I didn't have a working microsd available I did a "manual" installation, I flashed rkspi_loader.img into the SPI taken from the armbian image and then flashed the armbian img directly to the nvme drive with an usb adapter from my PC. All is good and working fine, but I'm wondering if I'm missing any settings that gets applied during the armbian-install process (are there any?) that …

root@orangepizeroplus2:/# modprobe gc2035 modprobe: FATAL: Module gc2035 not found in directory /lib/modules/4.14.67-sunxi64 root@orangepizeroplus2:/# modprobe vfe_v4l2 modprobe: FATAL: Module vfe_v4l2 not found in directory /lib/modules/4.14.67-sunxi64 OrangePi ZeroPlus H5, use armbian official build, but no gc2035+vfe_v4l2 module? I heared of these modules already built-in?

Hi all, I have several Nanopi M4V2's running 24/7 which I use for prototyping my projects , I would like a UPS as a safety backup to power them. I'm in the UK has anybody got any suggestions as to what I should consider ? I hope this is the right forum for this post

Hi, I searched around for any new info on the 3rd USB port (header pins next to the 40pin header) and couldn't find anything new than the 2016 post that found its existance, the rest I found was acknowledgement that the H3 has 3 real USB ports, I am trying to enable this port since it seems it isn't enabled by default even in the latest Armbian, how exactly can it be enabled, the whole script.bin change from 2016 got me confused, is it the usb3host option in armbian-config? Edit, spoke too soon, even though the info is missing actually, it was the usb3host in armbian-config>system>hardware, I had the pins the wrong way, D+ is on the outside. Also w…

Hello. I have "Debian GNU/Linux 9 (stretch)" on CubieTruck. After installing Apache2 i get problems with /var folder (that is symlink on hdd folder). Apache2 dont see files in it. So i print stat for this folder from commandline and from php in Apache. That is from command line: root@cubietruck:/mnt/var/armbian/apache2/www/html# stat /mnt/var/armbian/var File: /mnt/var/armbian/var Size: 4096 Blocks: 8 IO Block: 4096 directory Device: 801h/2049d Inode: 2097154 Links: 13 Access: (0755/drwxr-xr-x) Uid: ( 0/ root) Gid: ( 0/ root) Access: 2018-02-10 14:35:14.025501481 +0300 Modify: 2018-02-04 09:1…

Hello, is there an armbian available for Tinkerboard 2 (RK3399)? Mainly I need to setup a headless system with working i2c, pwm and gpio . Thanks!

i am using arduino ide, my plan is to keep the eps32 connected to rock3a, and access the debug logs from the browser, this is the code i have used to see if the esp32 is able to read data form rock 3a, #define RXD2 16 #define TXD2 17 void setup() { // Note the format for setting a serial port is as follows: Serial2.begin(baud-rate, protocol, RX pin, TX pin); Serial.begin(115200); //Serial1.begin(9600, SERIAL_8N1, RXD2, TXD2); Serial2.begin(15000000, SERIAL_8N1, RXD2, TXD2); Serial.println("Serial Txd is on pin: "+String(TX)); Serial.println("Serial Rxd is on pin: "+String(RX)); } void loop() { //Choose Serial1 or Serial2 as required …

I have an orange pi 2e running armbian 5.31. I wanted to use it as a pihole for blocking advertisements however it seems that it only has a link local address but no IPV6 connection to the internet. pinging 2001:4860:4860::8888 will show destination unreachable: Beyond scope of source address. However I have another PI, windows desktop on the same network than can ping the same IPV6 address. Is there a way to force "enable" IPV6?

Is the new orange pin zero 2 with the Alienware H616 supported. Board is not shown on downloads page, but that anorthern image for different board will work ?

Is it possible to have two operating systems on a SD card with provision to select the OS at bootup (e.g Grub), or selecting OS for next bootup at shutdown ? Rein.

The hardware watchdog /dev/watchdog does not reboot the board in a brand new installation with 22.02 image. What happens instead is the green LED on board goes off, both LEDs on ethernet port go on and thats it - boards halt. However, if I flash previous 21.08 to sdcard everything works fine, even after I upgraded the installation via apt-get update & apt-get upgrade to latest packages.

Tried to build making a new git clone of the repository. So far tried to test by building orangepipcplus and orangepiplus2e, both stop in the screen 'Choose image type'. Options selected for both are 'Os image for installation to SD card', 'vendor provided / legacy ..) kernel, 'Debian 8 jessie', 'Image with desktop'environment'. Also, another try to build for nanopineo stopped in the same place. It seems that today's commits (29/12/2016) got something to do with this, I was able to generate images up to yesterday. @Igor, @zador.blood.stained can you please let me know if it works ok with you after today's commits?

Hi, I try to connect a tft 240x240 display via SPI with my BPI m2zero and i am looking for a suitable library written in C. The display uses ST7789 driver and it will be used in combination with thermal camera. I've tried to use producers library for RPi https://www.waveshare.com/wiki/1.54inch_LCD_Module but the screen only blinks when i run a program with test bitmap. I tested it on Arduino and the display works fine. If someone was able to run such a display, can you share your library? Thanks for all the help

Hello. I'm looking for a method disable wifi/hdmi/usb hardware. I already found h3consumption, but it it not fit for my system (3.x kernel supported only (My system use 5.10.x kernel)) in case of disabling Wifi, below command is correct? (for lower power consumption) $ ifconfig wlan0 down any suggestion will be ok. plase tell me how to solve this.

Hi, I'm trying to work with the CedarX/Cedrus Video Engine (running in Allwinner A20). It works smoothly with my patched FFmpeg; for example: ffmpeg -f v4l2 -r 30 -pix_fmt nv12 -video_size 1280x720 -i /dev/video0 -vcodec cedrus264 -pix_fmt nv12 -qp 15 -f rtsp -rtsp_transport tcp rtsp://192.168.10.11/live/test I need to use pixel format RGB24, but as far as I understand, I'm limited to work with NV12 (or NV16) pixel format. Does this limitation is due to: My FFmpeg patch (I think not...) CedarX/Cedrus driver implementation. Hardware limitation. Thanks for the help, Joseph

Bad news (if you didnt know), the rockchip bsp kernel is an android kernel. After browsing the sources I found multiple android-only files... Luckly its supported by linux kernel.

Hello, is it possible to use GPIO Pins with this OS? I would like to use this code: http://mujweb.cz/tlc/RasPi-SMT/ Board: OrangePI PC I decided to use this OS as the original images doesnt seem to support an USB WLAN adapter with atheros chipset I am using. This OS seems to work well with it.

Armbian trixie 24.2.0-trunk.272 - kernel 6.7.0-rc7 Connecting over ssh. When I shutdown the pi (sudo poweroff) it disconnects the ssh session but does not shut down completely. Network and heartbeat leds still flashing. Works fine with the legacy kernel 5.10 What am I missing? thanks

Recent apt upgrade caused problems with headless Orange PI+. It is not respond via ping and ssh. Prev upgrade also made the breaking change - eMMC's path in /dev was also changed. But 2020.02 was pretty stable. What packages should I put on the hold to prevent upgrading armbian specific packages? I maen what packages should i place in placeholder to prevent upgrade. echo "<package> hold" | sudo dpkg --set-selections Thanks in advance.

Hi, I installed a fresh Armbian_22.05.4_Rockpi-4a_sid_edge_5.18.0 first on SD-card, then I used nand-sata-install to copy system to emmc. After that I rebooted and set up the nas (rockpi-4a with 4 ssd-drives). I already used ssh remote shell to perform apt dist-upgrade and copying of about 6TB ... When all setup was finished, I shutdown the system, closed the tower and restarted again. On that restart, the network came up without inet-address. ifconfig showed eth0 and l0, but eth0 had a mac-address (not the one, I configured in armbianEnv.txt) but no ip-address. Here are some lines from syslog: Aug 28 15:57:01 mynas NetworkManager[1659…

How can I setup my banana pi M2 H2+ ARMBIAN 5.41 user-built Ubuntu 16.04.5 LTS 3.4.113-sun8i camera module I set this command "sudo modprobe sunxi_csi1" and returned: "modprobe: FATAL: Module sunxi_csi1 not found in directory /lib/modules/3.4.113-sun8i" I Don't see /dev/video0 Can I confirm and setup my camera module?

Has anyone managed to use a usb adapter to get mic/aux out working on an Orange Pi Zero LTS? I am thinking of getting something like this (apparently it works with linux): https://www.amazon.com/Adapter-Raspberry-External-Headphone-Microphone/dp/B07R6TMQ4C/ref=sr_1_19?crid=71ETFNJN8CS8&dchild=1&keywords=usb+mic+raspberry+pi&qid=1600173433&sprefix=usb+mic+rasp%2Caps%2C200&sr=8-19

Hello Armbian community, I recently purchased a Odroid N2+ board and am trying different OS. I flashed Armbian_22.08.1_Odroidn2_jammy_current_5.10.139.img.xz on eMMC card. The first boot up works fine. I was prompted to set root password, new user credential and locals without any issue. I then used 'armbian-config' to navigate the different settings. In the system security menu, I applied the firmware update (that's what the menu called), I assume it runs apt update && apt upgrade. After completion, it prompts me to reboot. So I did. Then the Armbian cannot boot up anymore. I am using Odroid N2+ headless, so I can only see the board blue led not flashi…

Hello I would like to backup my SD card so that in case of crash I do not have to make all the config again. I tried to make the image with Win32Diskimg, the image is done, but when I put it again on the board, it doesn't boot. Is there a special process to make this image ? Thanks Greg

This is bazel 0.10.0 for H3 device like: nanopi m1, nano pi neo, orange pi pc, orange pi one,... You'll need this when building tensorflow from source for our H3. Copy this file to /usr/local/bin to use it. Sorry for my bad English Bazel

Hi. I bought some time ago a OPi One and a OPi PC. Yesterday i tried to setup them with armbian without success until I switched images from one to another and...it worked. I think that the download page for each should be fixed ( 5.4.20 image ). Made me crazy as a beginner until I figured out, tried different micro sd cards, different power supplies... Sorry for my english. Many thanks for developers who makes something stable for this boards.

I have this small 64bit H6 orange pi and SSD connected via USB, runs "Armbian 22.11.4 Jammy". Now I am trying to move /home and /tmp to the USB mounted drive to save RAM and move lots of writes from an SD card to a bigger and more capable external SSD. I uninstalled overlayfs, disabled tmp.mount and whatever there was with "tmp" in the service name. aik@hass:~$ cat /etc/fstab UUID=ecc7fb6d-12ab-41b9-b11a-c2c9b78e3bd1 / ext4 defaults,noatime 0 1 /dev/sda2 none swap defaults 0 0 /dev/sda3 /mnt/sda ext4 defaults,sync 0 0 /dev/sda4 /tmp ext4 defaults,sync 0 0 aik@hass:~$ cat /proc/cmdline root=UUID=ecc7fb6d-12ab-41b9-b11a-c2c9b78e3bd1 rootwait rootfst…

hello everyone, i realized, that the new armbian-images (buster & bionic kernel 5.10.y) on a nanopi neo core / air will have some problems. i can build the sd-card and the nano boots up and gets an ip-address. but if i try to login via ssh (headless installation) i got the "access denied" msg. something gona wrong with the user root & the init-password (1234). so i try to install focal (same kernel) and it works. somebody got the same problem like me? ore resolve that? kind regards andre

Is khadas edge supported ?. Once it is in the download section, once it is gone. Not in the archival images?

Hi, I have installaled a web server with "armbian-config" 3 Partie software on a Cubietruck3. All ISPConfig is installed and it's up to date. Now, I want to create a database with phpmyadmin as root without going through ISPConfig. I can not connect with phpmyadmin as root. Do you know the password created when installing ISPConfig. I looked for it in the ISP-config installation scipts but I did not find anything Thanks François

Hi I have a5x tv box.Rk3328 chipset. Iam Accidently broke the emmc chip.Damaged. Right now can't boot on sd card. I think need the disable emmc chip on to the dtb file.How can ı do this? I connect tx rx cable to uart debug tool and i get the this log. DDR version 1.13 20180428 ID:0xFFF In DDR3 786MHz Bus Width=32 Col=11 Bank=8 Row=16 CS=1 Die Bus-Width=16 Size=4096MB ddrconfig:3 OUT Boot1 Release Time: Feb 2 2018 15:41:39, version: 2.46 ChipType = 0x11, 141 SdmmcInit=2 0 BootCapSize=0 UserCapSize=0MB FwPartOffset=2000 , 0 SdmmcInit=0 0 BootCapSize=0 UserCapSize=7580MB FwP…

For a project, I need the Linux desktop to be set to 16 bits per pixel. I can't find any documentation about how to do this on the mainline kernel. Anyone?

Hello, i was trying to connect sensors via i2c, and neither wiringPi.h nor i2c-dev.h are comiting Read/Write comands. The file descriptor is given a value, so i think the connection worked, but functions like : i2c_smbus_read_byte_data(FILEDESCRIPTOR, (u_int8_t)REGISTERADRESS) just pop errors. Do you guys have any idea? Thanks for any help! edit: i have also included /linux/i2c.h and the function error persists. "I2C_SMBUS_READ_BYTE_DATA was not declared in this scope"

Hi there, I have a working armbian jammy on my odroid c2, but I'm unable to get SPI to work. I tried to load the three as described in the odroid wiki (https://wiki.odroid.com/odroid-xu4/application_note/gpio/spi#tab__odroid-c2😞 sudo modprobe spidev sudo modprobe spi_gpio sudo modprobe spi_bitbang ...and that works, but unfortunately no device file is created. I believe SPI needs to be enabled somewhere additonally. In the "armbian-config" hardware section, there is only an entry for the odroid n2, which does not help/work for me. Are there any other hints somebody can give me to make it work? thanks a…

Good morning, I've got a Libre Computer Renegade, with Amrbian Bullseye minimal (on an sd card) . Changing HDMI monitors (of different sizes and resolutions) the board does not adjust automatically the resolution, so, sometimes the display is unreadable because written are too small, and I can't set a resolution to beng able to use it. Surfing armbian docs, it seems to be an environment problems that could be solved by chanching u-boot parameters. I tried to enter in u-boot command shell but I can't. Pushing backspace while it is booting make no effect (tried also with serial console but it didn't work). How can I enter in u-boot environment to set an …

I am aware that the Raspberry Pi 1, 2,3 can transmit Radio waves on GPIO pin 4 and 18. There are even special skins that filter the output. " Previously we posted about the Raspberry Pi’s ability to modulate one of its pins to produce FM transmissions with PiFM. A developer (F5OEO) has recently expanded on this idea, and now the Raspberry Pi is capable of modulating and transmitting FM, AM, SSB, SSTV and FSQ signals anywhere between 130 kHz to 750 MHz. To transmit with the Raspberry Pi all you need to do is plug in a wire antenna to Pin 12 (GPIO 18) on the GPIO port and run the PiTx software by piping in an audio file or image for SSTV. " …