Beginners

Support for bullseye dropped?

Is it possible to use uart rts gpio on mainline? May be like discribed here https://kernel.googlesource.com/pub/scm/linux/kernel/git/next/linux-next/+/refs/heads/akpm-base/Documentation/devicetree/bindings/serial/serial.txt

Hello. I need to boot armbian without logs and start my application. I rebuilt and configured uboot and create splash screen with plymouth, so i have no any logs on screen until os boots. I use autologin by NODM, but after splash screen login string appears for a second. Can i disable this output? And the next question: how can i start my gui application without starting desktop?

I’m running Armbian 20.05.7 stable on an Odroid HC2 (XU4). I installed Docker Compose using the instrux found in the Linux section of the Docker install page. I’m logged in as root via SSH. I run the curl command (which I literally copied/pasted from the docs install page) curl -L "https://github.com/docker/compose/releases/download/1.26.2/docker-compose-$(uname -s)-$(uname -m)" -o /usr/local/bin/docker-compose then chmod +x /usr/local/bin/docker-compose and I check it with which docker-compose which returns: /usr/local/bin/docker-compose When I try to test the installation… docker-compose --version it returns: bash: /usr/b…

Hi all again, I need disable this hardware on the kernel of the board because i dont use it: HDMI Audio IR receiver Camera LCD screen For do this i should recompile the kernel? or i can desactivate in the armbian with out recompile? And how i do this? i am very noob with kernels. Best Regards!

Hello, I run a clearfogpro, this problem is not board specific, but I would like to use a huawei e3372h-153 USB 4G dongle on this board which has a USB3 port. The current version of armbian is Debian Buster Linux 4.14.135-mvebu. This dongle is in stick mode, as opposed to the hilink mode. In stick mode, when plugging the dongle, two devices appear : /dev/ttyUSB0 and /dev/cdc-ncm1. With the former I can issue AT commands to the dongle, the latter is the modem itself with the NCM protocol, known to be faster than PPP. There is also an wwan interface appearing with ifconfig -a. However, I do not know…

hey, after updating my nanopct4 and rockpi-4b to from 20.05 to 20.08 RDP stopped working for me, only black screen. After reading all the messy logs, fresh install etc, I found a simple working solution online: In /etc/xrdp/startwm.sh change #!/bin/sh to #!/bin/bash Sources: https://github.com/neutrinolabs/xrdp/issues/1630 https://askubuntu.com/questions/1166568/remote-desktop-blue-screen-after-login Maybe others are affected too, don't know about Ubuntu.

I'm not sure if anyone is interested in a very small distro without gcc, but I spent some time the last week using buildroot and armbian's source files to create a 3.4.112-rt image for the nanopi neo. It is going to be part of a realtime audio project (think synth or guitar pedal) that I'm working on and it demands a quick boot, among other things. There is also a mainline version, but it doesn't have all the fixings you folks like, so I don't know if you'd want to use that. You can find the build scripts and config files on my github. I'll be posting the legacy image in a zip file tonight, once I verify everything is reproducible. I…

I have read a few articles on kodi on Armbian. I am currently using RetrOrangePi as it is close to what i want. What i want is: A linux desktop - dont care which one Kodi with h/w acceleration RetrOranagePi does this but boots up into ES then you have to go to the desktop and currently i can't get kodo it run from desktop, so i have to go back into ES to run Kodi and i think (not sure) i can't update the os. so can i get the RetrOrangePi working kodi on an Armbian os? cheers

I can not ssh into my Orange Pi Zero 2 . I get "incorrect password , permission denied" repeatedly. I have loaded latest Armbian 23.11 and some older images all with same result. I used "1234" as password. My Pc has Linux Mint 21.2 and I used Xfce terminal also XTerm. Both My Pc and Orange Pi Zero2 are plugged into same switch. Also used a laptop with Linux Mint 21.1 and Xfce Terminal with same result. Any ideas would be great , I'm just any average user that tinkers. Thanks

Hello! I follow instruction "Add names of overlays you want to activate to overlays= line in /boot/armbianEnv.txt" I try to find /boot/armbianEnv.txt but nothing. I see Build tools overview from https://github.com/armbian/build/blob/fcb8b6f195bbb76c83c612c425fdf08cfd48c68b/README.md And nothing about /boot/armbianEnv.txt May be documentation talking about build/config/bootenvrockchip.txt and build/config/zynq.txt and others txt files in build/config/ ? It looks like /boot/armbianEnv.txt is file on microSD after I burn armbian image on it. But reading docs I don't understand nothing about build/config/bootenv/rockchip.txt

I'm struggling to use the armbian-config tool to setup a hotspot when I have two radios. Can someone share with me the intended workflow/step using armbian-config? I get asked twice for Default interface and the 2nd dialog is throwing me off. My board and radios work fine, but my network is suffering from insufficient user IQ. :-(

Hello, I am new on the embedded system. I am using Orange Pi zero and I am having stuff with wlan configuration. I want to run the static ip for wifi on the board and reconnect after every time rebooting How I do that? I use 2 files below The eth0 works fine with this setup otherwise the wlan not active even though I used ifconfig wlan0 up but I using ifconfig wlan0 down, it got the static ip like the configuration file then I can't turn on or off using ifconfig up/down one more time Anyone help me? Thanks a lot!

So if I wanted to connect from smartphone via 3g to Node-red, Mopidy or Mycroft or other stuff what would be the easiest way to do... I'd require a letsencrypt cert right? So I can https the stuff? And then later no-ip.com? Could someone help me step by step please?

It's a Debian stretch server (Armbian to be specific). When I ran "apt-get update" the day before yesterday, it gave me an error: "The following signatures couldn't be verified because the public key is not available: NO_PUBKEY 648ACFD622F3D138 NO_PUBKEY 0E98404D386FA1D9". I searched the Internet and finally resolved the issue by running the following commands: apt-key adv --keyserver keyserver.ubuntu.com --recv-keys 648ACFD622F3D138 apt-key adv --keyserver keyserver.ubuntu.com --recv-keys 0E98404D386FA1D9 Initially I tried to use "--keyserver keyring.debian.org" but it didn't work. Therefore, I did some further research, and I read from https://wiki.debian.…

Armbian documentation on Overlays refers to /boot/armbianEnv.txt. But in the version of Armbian that I'm running (on a Cubietruck, ARMBIAN 5.36 user-built Debian GNU/Linux 8 (jessie) 4.13.16-sunxi) there is no such file. There is however a copy in directory /usr/share/armbian. Is this the overlay file that is processed at start-up? If so, it would be good if the documentation was updated.

UPDATE: Today I build it again and now it's working, I think someone has change something. Thank you :-) OLD: I created an new board, based on the lime-a33.conf with BOOTCONFIG="q8_a33_tablet_1024x600_defconfig" and build a Debian Stretch Image with mainline Kernel 4.13 / 4.14. The SD Card is booting with a nice screen output but only to Kernel Boot, then the screen freezes. The Serial connection is only in the SD Adapter and I cant use it if I'm booting from it, or is there a possibility ?? I was checking devuan.org and this Image is booting the Tablet, with Kernel 4.1x. So I want to debug the Armbian Kernel wit…

Dear all, I love Armbian on my Banana Pro and so I also would like to use this OS on my brand mew Odroic C2. Every installation and configuration works except installing TVHeandend. I tried to compile it because via armbian-config it does not work. But it does not matter which branch I use and which option I try it is not possibe to install on mainline or legacy version. I do not need transcoding - the TVHeadend server just should serve my Kodi with dvbs. Can anybody send me an instruction to compile TVHeadend with Armbian on Odroid C2 sucessuflly? Maybe it is possible to compile completely without ffmpeg? T…

Hello, I faced an issue yesterday, while trying to create a custom image with debian bullseye, a specific 5.11 rc1 kernel tree and a couple of packages. The output looked like this: [ o.k. ] Installing base system [ Stage 2/2 ] /bin/bash: warning: setlocale: LC_ALL: cannot change locale (en_US.UTF-8) W: Failure trying to run: /sbin/ldconfig W: See //debootstrap/debootstrap.log for details [ error ] ERROR in function create_rootfs_cache [ debootstrap.sh:177 ] [ error ] Debootstrap base system second stage failed [ o.k. ] Process terminated [ o.k. ] Unmounting [ /home/basti/Kernel/build/.tmp/rootfs-dev-nanopct4-bullseye-no-yes/ ] [ error ] ERROR in functi…

If I want to use such device on prange pi one, do I need to install anything I use it a lot with Raspberry but when trying with Orange Pi I do not get prompt (login screen) https://encrypted-tbn0.gstatic.com/images?q=tbn:ANd9GcTrkoGB_leq-7hEJRtlZjAe345K1-v96BhenuE9EmdglEs3VUDY

Hello All, I've tried Armbian_5.59_Xt-q8l-v10_Ubuntu_xenial_dev_4.18.6_desktop.img image taken from Though the system mostly works, in the main desktop menu (the one that opens clicking on left upper corner of the screen) I see no menu entry that can be interpreted as software management. By software management I mean a GUI application allowing to browse available package, read their descriptions and install or remove the packages. Examples of software management are https://en.wikipedia.org/wiki/Synaptic_(software) , https://en.opensuse.org/YaST_Software_Management , https://delightlylinux.wordpress.com/2016/12/23/software-a-better-software-…

Hi I would like to add Armbian version to banner after login (eg. v5.10) to be sure that I'm using latest version. Is this value stored somewhere in the filesystem? I already checked: /proc/version /etc/debian_version /etc/os-release but it's not there. I found it in /etc/armbian.txt but this is plain text file and parsing it to fetch the value is a little overkill. Is there a better place where I can find it?

I am using Armbian for a long time on mi Orangepi mini (A20), board not supported but installing image Bananapi M1 it has been working very well adding fdtfile=sun7i-a20-orangepi-mini.dtb on /boot/armbianEnv.txt After running apt upgrade kernel package is upgraded from 5.10.60-sunxi to 5.15.25-sunxi i get this errors: S'està configurant linux-image-current-sunxi (22.02.1)… update-initramfs: Generating /boot/initrd.img-5.15.25-sunxi modinfo: ERROR: Module /lib/modules/5.15.25-sunxi/kernel/drivers/cdrom/cdrom.ko.xz not found. modinfo: ERROR: Module /lib/modules/5.15.25-sunxi/kernel/fs/isofs/isofs.ko.xz not found. modinfo: ERROR: Module /lib/modules/5.15.25-s…

I guess this is hardware-independent, so I post here. Looking for ways to disable IPv6 I found 3 ways to achieve this on Linux, none of them really working for armbian debian build. 1. /etc/sysctl.conf: net.ipv6.conf.all.disable_ipv6 = 1 net.ipv6.conf.default.disable_ipv6 = 1 net.ipv6.conf.lo.disable_ipv6 = 1 this disables the network interfaces to use IPv6, not IPv6 itself. This method is also known to cause trouble e.g with X-Forwarding via SSH and Postfix server. netstat still lists IPv6 entries 2. /etc/default/grub (GRUB tells the kernel not to load IPv6) This does not exist in armbian, I guess it is simply not using GRUB …

Hi, I'm experiencing OragePI PC with Zoneminder for the development of a video surveillance system. It's possible to insert Zoneminder in armbian repository? The update of this important program in automatic mode would be outstanding. Thank you.

Breaking the ice here. So hello everyone. I am still entry into SBCs and have been loving every moment of it. I started with the Raspberry PI 3B, and have recently been playing with the new Asus Tinkerboard. One of my SBC projects is to build a little media streaming device for some dumb monitors with HDMi input I have lying around. The Tinkerboard was very appealing to me because of its gigabit Ethernet, I thought it would make a much better quality internet streaming device. We seem to be lacking a browser for ARMh7 that can support Netflix and other like services playback. chromium is missing the needed WideVine plugin, and I have yet to find a …

Hi, Got a latest Armbian jessie image 5.24 with kernel 3.4.113, and could not find pulseaudio in it. I thought it was already present. Is there any hint/guide for installation to OPi or FA H3 boards with Armbian? Christos

I'm trying to create a microSD card to boot Armbian, but first would be inserted into a Windows laptop to edit some configuration. To make the microSD show up in Windows, the first partition must be a FAT partition, and so Linux would be ext4 partion 2. I suspect I'll need to put the /boot partition on the FAT volume, with directions to load from mmcblk1p2. In case it matters, this is a Rock64 without emmc. I've just started this research, but I'd be grateful for any u-boot-savvy person's help here. Thanks.

Getting into buildroot and yocto seems a bit too much for me to get an A+B style update possibility. I would like to stick with the quality images provided by Armbian. The following applies to a NanoPi-NEO3 others SBC might have different partition layouts. From what I understood is that uboot looks for /boot in /dev/mmcblk0p1 reads the boot.cmd/scr and armbianEnv.txt and then boots the kernel accordingly. The armbianEnv.txt seems to point the kernel to the root partition using the rootdev directive. If /dev/mmcblk0p1 would now only hold /boot would it be possible to point to a different partition for the rootfs using armbianEnv.txt? …

i would like to reboot my cubi every day at 3 o clock, my linux experience is not so good. can same one explain me how i can do it with cron, because i have no clue with the cron.d/crone.daily etc.

Hi all, I use a cubieboard3 as a web server. For several months, joomla tells me that I am PHP 7.0.33-0 + deb9u7et that I need to update my version of php to 7.3 or later. In the updates of the bone, I never see these updates of PHP, must it be done manually and how? I am in Debian Stretch with Armbian Linux 4.19.62-sunxi. Thank you François

Hello everyone! I tried to enable cedrus264 encoder/decoder on my old OrangePI Lite 2 (revision 1 if I am right). I used stulluk's repository as the base to patch the last FFMpeg revision and to add cedrus264 encoder using the new FFMpeg API. The result is built and tested. Unfortunately, I have had no success: the encoder says: ffmpeg -f video4linux2 -input_format mjpeg -video_size 1280x720 -i /dev/video1 -c:v cedrus264 -pix_fmt nv12 -f mp4 video.mp4 ffmpeg version N-103904-gb2538ce578 Copyright (c) 2000-2021 the FFmpeg developers built with clang version 12.0.1 (https://github.com/llvm/llvm-project.git fed41342a82f5a3a9201819a82bf7a48313e296…

New user here Quick question re: the "Install to eMMC" script detailed in the getting started guide here: https://docs.armbian.com/User-Guide_Getting-Started/#how-to-install-to-emmc-nand-sata-usb Does it put a fresh install of Armbian onto the eMMC? or Does it move the configured install from the SD card to the eMMC? The situation is that I have a live home server which is in use by the family all the time but is playing up a little so i was going to re-install it. Rather than take it offline and configure the board all in one go which would take a while. I wondered if i could boot from a new SD card and configure it as needed (over a f…

Hello everybody, had to reinstall my pine64 completely since it wasnt reachable over ethernet anymore, dont know why but after a restart on debian stretch it seemed that ethernet wasnt initialized anymore (lights were not even starting anymore) so i formated the sd card and went to the download directoy and i was surprised to only see debian jessie images left, is there a reason for that? anyway, so i downloaded the current stable realease but now i m having trouble with the repositories, it seems that i cannot update properly since i get an error message for following index W: Failed to fetch http://security.debian.org/dist…

Since December 2013, when I started to deal with CLI Debian images and support them, things become ... bigger. My prime motivation was only to build an working Linux image for some amateur based services. Project brought a lot of fun, a lot of new toys on my desk but also tears and frustrations. I hope and wish that public use our work to the greatest degree. Blog comments - your questions and (not only my) answers - become large and valuable knowledge base for ARM single board computers and general Debian / Ubuntu problems. I already manage to pack some of the into the FAQ but I'll need your help and patience within summarizing this into General FAQ. You only need…

Very often when i do apt update or apt dist-upgrade some of the armbian mirrors acts up and pretty much denies connections (it isnt the generic debian mirrors as other distros are working fine). I assume they are just overloaded and theres not much to do about that. But it has caused one of my system to be out of date for a few weeks I assume because the unattended upgrade script doesnt retry. How do I get this to work? for example some times i have to retry up to 10 times before I can get apt to work (when I try manually). The apt configuration in etc is a bit of magic to me so Id appreciate if someone can guide me to get unattended upgrades to retry connecti…

Orange Pi PC = Server = Debian Jessie Programs does not start automatically at boot, I tested the deluge, transmission and vsftpd; Same commands used in Raspbian Jessie: Does not start automatic: sudo update-rc.d deluge-daemon defaults sudo update-rc.d transmission-daemon defaults

R40 is a new SoC from Allwinner known as 'quad-core A20 successor' (link to datasheet). It shares most hardware details with A20 (true SATA, GbE -- EMAC and GMAC listed separately -- 2 USB2.0 host ports, one USB OTG, and fortunately also PMIC/battery support (link to AXP221s datasheet). Unfortunately Allwinner chose a manufacturing partner known for never providing exact specs/info to produce the first R40 device available. So we won't get any info about performance and working hardware features unless we buy this device on our own and test. I just had a quick look into one already released OS image 'funnily' based on one of our Armbian OS images for a H3 board: …

I have a Clusterboard and the latest images (Stretch and Bionic) do not work with my SOPINE modules. Legacy 3.10 (Xenial) works. I've been told this is a problem that has been resolved before but somehow the fix has been left out of the latest images. What is the process for getting it back in? armbianator didn't generate a URL so I'm manually pasting it here: -------------------------------------------------------------------------- Spoiler ### Activated 4 lzo zram swap devices with 248 MB each ### Activated Armbian ramlog partition with compression ### Activated 4 lzo zram swap devices with …

Hi, My apologies if this is not the right sub forum. I have a DLink DNS-340L with the specs as below; CPU Marvell Armada 370 88F6707-A1 C120 @ 1.2GHz RAM 512 MB Hynix DDR3 (x2) Flash 128 MB Hynix Ethernet Marvell 88E1518 Gigabit Ethernet (x2) USB 3.0 Etron Tech EJ168A SATA Marvell 88SE9215 4 port PCIe 2.0 SATA 6Gb/s and PATA Host Controller #cat /proc/cpuinfo Processor : Marvell PJ4Bv7 Processor rev 1 (v7l) BogoMIPS : 1196.85 Features : swp half thumb fastmult vfp edsp vfpv3 vfpv3d16 tls CPU implementer : 0x56 CPU architecture: 7 CPU variant : 0x1 CPU part : 0x581 CPU revision : 1 I …

I have worked with Raspberry pi for some time but I need a board with SATA port so I can plug in my hard drive directly so I got a Banana Pi M2U from ebay. When It arrived I thought this will be normal as my Raspberry pi So I downloaded image (Raspbian Jiessie) from http://www.banana-pi.org/m2u-download.html and burn it to SD card and boot up. It booted up I worked it with for few weeks and noticed it's not stable Pi Randomly Crash and I can't use a sata port multiplier. Then I found about armbian, So I went to armbian site and download the image for banana pi m2 and burn it with etcher and put the sd card to pi but it won't boot up, no display and and only one led on the…

Dear community, dear @Igor (as maintainer of NEO3 CSC), thanks a lot for the NEO3 support. This board ran rock solid for me approx. two years straight – much more stable than my other SBCs running Armbian (due to various reasons, no offense :)). However, the board failed to boot with "ERROR: Did not find a cmdline Flattened Device Tree". It appears that ``rk3328-nanopi-neo3-rev02.dtb`` went missing. This must have happened when upgrading the package ``linux-dtb-current-rockchip64`` from 21.08.2 to 22.02.1. As a workaround, it helps to (download the CSC image for the board again, get the file out of the image,) place the file in ``/boo…

Hi! Have limited knowledge in linux, all self learned so bear with me if I sometimes sound like an i**ot in my wording. I have used lots of different Raspberry pi's but since they are near to impossible to get your hands on I figured I'd try out some of the alternate boards. Got myself a nanoPiNeo2, orangePiZero2 and an orangePiPC2 just for the fun of it. I have tried this on the nanoPi and the opiZero2 and run into the same problems, havent even opened the opiPC2 yet but I suspect it will be the same problem on that board. Downloaded armbian for each separate board (instead of debian) because I want to use the same system o…

Sorry for my stupid question. If I connect by TTL to USB adapter, after setting up login/password, terminal is freezing. Board is Nanopi NOE2. I think this is due to the fact that my adapter is warm or not of poor quality. While I order a new one, is there a way to enable ssh access over the lan network?

Installed desktop, ran start desktop. From there I was back in text mode. Rebooted still no desktop. Tried startx, xinit and, several other start desktop commands from various OS's. I've been working on this for 3 days now. Don't know what I'm missing. I also tried installing lightdm, no change. I could also use the shut down command. Tried everything I could think of there too. Any help would be greatly appreciated. I hate wasting your bandwidth and time. I'm stuck! I'm done wasting bandwidth and moved to time now. Funny it asks me startx like in (OS name). Wish I knew how to tell it Yes! exactly lol! Thanks in advance ROC-RK3328-CC Armbian 5.98 Renegade

Hi I found next script from git: https://github.com/Vitalik-Samets/DHT11-Python-library-Orange-PI It working OK. But I faced with problem how to upload my data to https://thingspeak.com With next code from git: https://github.com/magiccow/mqtt-client I'm able to upload constant data to my channel.. BUt if I want to put in python code varible it do not want to uplad data. Can someone help me how to do? #import RPi.GPIO as GPIO import dht11 import time import datetime import paho.mqtt.client as mqtt # initialize GPIO #gpio.setwarnings(False) #gpio.setmode(GPIO.BCM) PIN2 = port.PA6 gpio.init() #gpio.cleanup() def fun1(): fun1.…

I'm looking forward to buying a BIGTREETECH Pi v1.2 board to use as a slim home server to replace my Orange Pi PC. I've had pretty good experience with Armbian so far and I would like to make sure I can continue using it with the new board. I didn't find a specific image for BTT Pi v1.2, but I did find a "Desktop > ARM64" entry. I'm confused on what should I use and whether it's supported at all. Can someone clarify that for me? Скрытый текст Changed the post tag to the closest one to this board, since it doesn't allow posting without a tag, and I misunderstood what "unmatched" tag meant

Mini tutorial I am putting here some notes for posterity In the current version of armbian (testing H6) I use X11 / Xorg only reaches 1024x768, but my display reaches 1440x900. To add this new resolution to the list of Settings/Display you have to give these commands: # xrandr --listmonitors (this command serves to see what it's called, the hdmi output) # cvt 1440 900 (output: # 1440x900 59.89 Hz (CVT 1.30MA) hsync: 55.93 kHz; pclk: 106.50 MHz Modeline "1440x900_60.00" 106.50 1440 1528 1672 1904 900 903 909 934 -hsync +vsync ) # xrandr --newmode "1440x900_60.00" 106.50 1440 1528 1672 1904 900 903 909 934 -h…

Hi, I tried the release upgrade from xenial to bionic on the orange pi pc. Commands: sudo apt install update-manager-core sudo do-release-upgrade But the upgrade failed: orange@orangepipc:~$ sudo apt install -f Reading package lists... Done Building aml-0-2 lp-solve python3-lxml python3-pycurl Use 'sudo apt autoremove' to remove them. 0 upgraded, 0 newly installed, 0 to remove and 512 not upgraded. orange@orangepipc:~$ sudo apt update && sudo apt dist-upgrade && sudo apt autoremove && sudo apt autoclean Hit:1 http://ports.ubuntu.com bionic InRelease Hit:2 http://ports.ubuntu.com bionic-security InRelease Hit:3 http://a…

Is there a way to make armbian find my modem auto? I am running Orange Pi One with Armbian 5.20 Debian Jesse And Orange Pi PC with Armbian 5.20 Debian Jesse My issue is that it finds the flash memory in my modem but not the modem itself i have to manually set it to modem via this command usb_modeswitch -v 12d1 -p 1f01 -M '55534243123456780000000000000011062000000101000100000000000000' Now the OS see it as a modem and i can run command dhclient -v eth1 And it will load up the eth1 and it will work fine. Issue is i have to do those steps after reboot. On my Rasberry device i run Raspberrian and it does all those steps per automatic its plug and play. Am…

Hi community, I am a newbie when it comes to SBCs and Armbian, but I will do my best to thoroughly explain the problem. Problem: Armbian (Ubuntu 18.04 based, release for HC-1) Despite me rebooting a zillion times, resizing does not happen/finish/...: Error message (displayed exactly like this): Warning: a reboot is needed to finish resizing the filesystem Please reboot the system as soon as possible ilesystem Please reboot the system as soon as possible Hardware: SBC: Odroid HC-1 2GB RAM (known working) Storage: 1GB SD Card|250GB SSD (I know the SD is tiny, but I do not wa…

Hello fellow Linux gurus, Seeking for some assistance on this. I have NIC1 on 192.168.100.1/24 network with gateway set as 192.168.100.254 < this cant be changed. with a few PC’s connected to this. And NIC2 on 10.10.10.1/24 with a few devices on this. I want to be able to ping from PC1 connected to NIC1 on 192.168.100.100/24 to devices connected to NIC2 on 10.10.10.100/24 Could someone advise on the route settings I need to configure to make this work please ?

I am trying to leverage the first run script but am not having any luck. Here are the steps that I am following: 1. flashed the image onto the SD card 2. mounted SDcard on my mac (also tried steps from linux) 3. renamed the file from armbian_first_run.txt.template to armbian_first_run.txt 4. Edited the contents of the file to include the following: FR_general_delete_this_file_after_completion=1 FR_net_change_defaults=1 FR_net_ethernet_enabled=1 FR_net_wifi_enabled=0 FR_net_wifi_ssid='MySSID' FR_net_wifi_key='MyWiFiKEY' FR_net_wifi_countrycode='US' FR_net_use_static=1 FR_net_static_ip='192.168.1.201' FR_net_static_mask='255.255.2…

Hi, I'am the new one. I'am German and bought last month an OrangePi PC+ from AliExpress without a clue what todo with it, but it was cheap ;-) And it was perfect for my new OMV. Just installing OMV on top of Armbian / Jessie was not enough because of missing Quota Kernel Options. When setting up a development Enviroment, I found the excellent Build-Scripts of Armbian and thought, why not making an OMV-Image with the customize-image.sh. And here is it (quick and dirty v0.1) Just copy it with a modified kernel.config under userpatches. It should work with every supported Armbian Board as long as its working with Debian Jessie, because it installes OMV3.X I com…

Hello. I'm trying to install Jeedom on my Odroid C2 running Linux odroidc2 5.4.14-meson64 (Armbian_20.02.0-rc1) Distro has been updated with : apt-get update apt-get upgrade But when I download and run the install script : wget https://raw.githubusercontent.com/jeedom/core/stable/install/install.sh chmod +x install.sh sudo ./install.sh I have an error : Reading package lists... Done Building dependency tree Reading state information... Done Package mysql-client is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source Package my…

Hi Somehow iam not able to sucessfull setup a headless installation. I tested it with Orange Pi Zero (256mb rm) and Opi 2. I used the Armbian Stretch Image from the website, flashed it with Etcher. Modified before the first boot, the file /boot/armbian_first_run.txt.template to /boot/armbian_first_run.txt (and the content in it). #----------------------------------------------------------------- # Armbian first run configuration # Set optional end user configuration # - Rename this file from /boot/armbian_first_run.txt.template to /boot/armbian_first_run.txt # - Settings below will be applied only on 1st run of Armbian #-----------------------------…

I am with Armbian (ubuntu 18.04): Linux rockpi-4b 4.4.213-rockchip64 and when I installed chromium and tried to login gmail, I got below: Couldn't sign you in This browser or app may not be secure. Learn more Try using a different browser. If you’re already using a supported browser, you can refresh your screen and try again to sign in. The chromium version info: Version 80.0.3987.163 (Official Build) Built on Ubuntu , running on Ubuntu 18.04 (64-bit) Tried chrome UA spoofer with other UA text like safari or firefox, still the same feedback, no luck still. Any ideas?

good morning . can you explain something? . is it possible to use voice control to transmit audio wirelessly to the speakers with nanopi + NanoHat PCM5102A as happens with google assistant + chromecast audio?

I have multiple n2s and I don't want them all to be called odroidn2. What is the recommended way to change the hostname of an armbian system?

Hi, how can I remove all files of desktop (GUI) after installing with armbian-config. I am running armbian 4.19.62 sunxi #5.92 on BananaPi M1 I can disable the Desktop but I require the space for the server. Regards, Rein

Hi use a Nano Pi Neo with the Debian Server Image and and want to try install Pi-Hole but while the Installation Process i get a Error. The Script cant add a Password to the New User that Pi-Hole require (Yes i am use Root) i get a Stunnel4 error ?!?! Thanks for your Help

@TonyMac32 I have bought a Firefly-RK3399 from firefly ( http://shop.t-firefly.com/goods.php?id=45 ). I did not realize it at the time of purchase, but the Mosfets are unable to provide sufficient power for the board plus the USB ports, EDP connector, MIPI-CSI interface, M.2 slot, etc. I really love the IO of the board and want to try to find a way to get it to work (plus I don't have the money to go trying out more boards ). Would your idea help such a board? Thanks!

I am attempting to format and mount a 256GB MicroSD as an external USB device on an OPZ. Formatting in EXT4 consistently throws errors but using FAT32 or VFAT works fine with the inherent limitations of those file systems of permissions and 4GB file size. So I would like to try formatting as EXFAT file system. EXFAT formatting of the 256GB MicroSD works fine in Linux Peppermint. When attempting to install the exfat apps I get the following error: __ apt update (OK) apt-get install exfat-fuse (OK) apt-get install exfat-utils (fails) Package exfat-utils is not available, but is referred to by another package. This…

Hi, After days and days of research and some mistakes (I have buy Orange Pi plus 2 for the sata connector ) I have selected two board for build my NAS configuration. I want share with this community my considerations and read some other opinions about it. For both solutions i want to use a board like that for manage more than one HDD (and maybe some raid configurations): SATA Replicator on Amazon ODROID (both XU4 and HC1) Pros: The processor seems very powerful and this leave open my option for experimenting with various Cloud software and other (dlna servers, ftp, mini simple site server, transmission and so on). The docum…

Hi guys, I am using Armbian 5.23 Jessie Desktop version with retrorange pi, in my orange pi pc, using the firefox on youtube i can watch videos in 480p more than it the video is bad doesnt run good, i can't watch netflix because the version firefox esr 45 don't have support to html 5, and to use facebook have a delay to load the pages, i think the firefix version default of armbian aren't so good, i tryed update the firefox but i didn't found none tutorial for it, so someone knows how i update the firefox or install the other version with support to html 5? or someone knows how a install Chromium? Is normal the videos of 720 don't run good ? Thanks.

Recently we bought several BananaM2+ boards to integrate them into our future fiscal project We are developing software using Armbian Linux Debian-3.4.113-sun8i with standard core, which was chosen as a stable platform. For now we have a problem with integration. Due to our fiscal laws the board should be placed in the fiscal box with no access from outside. Now we are testing the board “on the table†using typical operations (even without loading it by typical cashiers operations) and the temperature rises very high. As a result the board starts switching off processor’s cores leaving only 1 working. We even still haven’t started testing the board placed into…

Im not sure if this is the right forum. Ive also Googled and found similar problems, but no solution that works for me. So Im happy to be LMGTFY with some hints, or shown the right forum :-) Im running an OrangePi Zero on Armbian (lsb_release reports Ubuntu 16.04.3 LTS). I have networking set up with both ethernet and wifi. Both work. But I want to have ethernet as static IP, and wireless as dhcp. My config looks like this: allow-hotplug eth0 iface eth0 inet static address 192.168.4.122 netmask 255.255.255.0 gateway 192.168.4.1 broadcast 192.168.4.255 dns-nameservers 8.8.8.8 8.8.8.4 allow-hotplug wlan0 auto wlan0 iface defaul…

rk3288.txtHi all, I stumbled across a board which may be of interest for one of my next projects. Here you can find a link to it, it is model JLD076 I have the board already on my desk, and as it is really well equipped with loads of interfaces, I would love to get Armbian working on it. J have attached the boot log from console to the message, it uses Uboot 2017, and seems to be based on a standard Rockchip eval board. Onboard peripherials are handled by the usual suspects: ethernet by RTL8211, WiFi by RTL8732, and some of the display links by ALC6540. eMMC is fixed on the baord, so RKUSB is needed (can be invoked by Uboot command or bu…

I run "armbianmonitor -u" and I got this : https://paste.armbian.com/bapohonaja My SBC is orangepi zero 2, and I tried to use it as a NAS. But sometime the system hangup because I push to much file in my usb-disk. And I G**gle about it. Somebody said because usb driver is "UAS". So I use command "lsusb -t" and bingo, my usb driver is "uas": ``` >: lsusb Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1…

Recently, successfully, upgraded from Ubuntu Focal to Ubuntu Jammy. Does anyone know the correct procedure to sort out the apt-key deprecation issue? I've read apt-key(8), but I don't fully understand what I need to do. I think a Linux guru is needed here. 🙂 ~$ sudo apt-get upgrade Reading package lists... Done Building dependency tree... Done Reading state information... Done Calculating upgrade... Done 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. myron@loki:~$ s apt-get update Hit:1 http://ports.ubuntu.com jammy InRelease Hit:2 http://ports.ubuntu.com jammy-security InRelease Hit:3 http://ports.ubuntu.com jammy-updates InRelease Hit:4…

My device is rtl8188cus

I have had a chinese sd card and armbian never booted on it(loop stuck). Now i have a Toshiba sd card, it booted.... once. Reflashed the sd card exactly as the 1st time,boot loop... no way. I would love to use armbian, but it seems really hard to get it work, any ideas? USED: Ubuntu 16 to flash 8gb toshiba sd card class 4 Model: Orange Pi lite Image: Armbian_5.30_Orangepilite_Ubuntu_xenial_default_3.4.113.img

Hello, I don't find a working way to completly disable the use of IPv6 on armbian. I'm using Armbian_5.69_Orangepipc2_Debian_stretch_next_4.19.13.img, fresh install with etcher/balena. I've added the file /etc/sysctl.d/10-NoIPv6.conf with this content: net.ipv6.conf.lo.disable_ipv6=1 net.ipv6.conf.default.disable_ipv6=1 net.ipv6.conf.all.disable_ipv6=1 I've modified /etc/hosts like that: 127.0.0.1 localhost orangepipc2 I've rebooted. But i still have ipv6 enabled and working, as the output of the "ip a" command give: 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default ql…

/var/log goes full every 15 min when i remove.Please see attachment download-2020.2.18_20.11.35-root-(projectok.com).tar.gz

I've got one of these boards. It is just Kernel development that has ceased as there are no maintainers? (Had I had the skills, I would have happily maintained it. ;-( ) Also, to get the latest Kernel later on, is it as simple as obtaining the official sources and then compiling (or cross-compiling to ARM) and then install the Kernel? On this one I'm a bit like a duck out of water and if anyone can point me along the right path, all help will be greatly appreciated.

I recently have been trying to enable SNAPD (SNAPPY) on 16.04 MATE and server. sudo apt install snapd installs fine, but when I try install a 'snap' it fails. this should work on 16.04. sudo snap install hello-world large error dump --- very misleading... When I checked to see what is going on with required apparmor module, I found it wasn't working. When I checked the kernel I found to my surprise that apparmor wasn't enabled. This has been enabled by default on Ubuntu for many, many years... It would appear that several kernel flags need to be set in order for apparmor to work set CONFIG_SECURITY_APPARMOR=y "If AppArmor should be sel…

I'm new to Debian. I've been using Arch for a while. This error occurs on my new RockPro64 when I try to run "apt update": Hit:1 http://ports.ubuntu.com focal InRelease Hit:2 http://ports.ubuntu.com focal-security InRelease Hit:3 http://ports.ubuntu.com focal-updates InRelease Hit:4 http://ports.ubuntu.com focal-backports InRelease Hit:5 https://us.mirrors.fossho.st/armbian/apt focal InRelease Reading package lists... Error! E: Problem parsing dependency 21 of gdc-9-x86-64-linux-gnux32:arm64=9.3.0-17ubuntu1~20.04cross1 E: Error occurred while processing gdc-9-x86-64-linux-gnux32 (NewVersion2) E: Problem with MergeList /var/lib/apt/lists/ports.ubuntu.com_dists_focal-up…

Hi evereyone, After doing some upgrades my Pi-hole Admin Page was not reachable anymore, while blocking still worked. 1. Problem The lighttpd service was not running because of the missing folder /var/log/lighttpd. So lighttpd crashes when trying to access /var/log/lighttpd/error.log and access.log. Reinstalling Pi-hole and lighttpd didnt solve the problem. So I first created the folder myself: sudo mkdir /var/log/lighttpd sudo chown -R www-data: www-data /var/log/lighttpd Then I reinstalled Pi-hole and lighttpd, now lighttpd was running. Unfortunatly now I ran into 403 - Forbidden when accessing…

Hello. I faced with a problem, I can't disable ipv6 completely on Armbian 23.05.1. Orange Pi PC. Tried to use armbian-config to disable ipv6 in Network menu, but no luck, apps can use it at the moment netstat -tulpn | grep ::: gives me udp6 0 0 :::53 :::* 1134/pihole-FTL udp6 0 0 :::111 :::* 1/init Thanks in advance.

Some days ago I installed the latest armbian updates to my armbian buster installation / openmediavault 5 on my odroid n2. After the installation of the following updates the cron jobs, which were setup on omv5 gui (not in crontab os) are not working anymore and are not started because of error: Here the update packages: armbian-config 20.08 armbian-firmware 20.08 linux-buster-root-legacy-odroidn2 20.08 linux-dtb-legacy-meson64 20.08 linux-image-legacy-meson64 20.08 linux-u-boot-odroidn2-legacy 20.08 Here the error message: /var/lib/openmediavault/cron.d/userdefined-ee6e5e4d-afef-449f-88fb-b6b4d0e4f1a5: 20: /etc/profile.d/ar…

Time to time i got following notification on Banana Pi M1. Only after reboot Banana starts working properly. How to tune zram to avoid such kind of issue? No tuning made till now Linux bananapi 4.19.17-sunxi #5.73 SMP Mon Jan 28 21:06:40 CET 2019 armv7l GNU/Linux error: Compressing program wrote following message to stderr when compressing log /var/log/letsencrypt/letsencrypt.log.1: gzip: stdout: No space left on device error: failed to compress log /var/log/letsencrypt/letsencrypt.log.1 error: Compressing program wrote following message to stderr when compressing log /var/log/wtmp.1: gzip: stdout: No space…

I have an orange pi with installed Ubuntu Bionic mainline Linux orangepione 4.14.65-sunxi, I have to create an economic access point with the Ralink MT7601U device (148f: 7601) already in possession, from the original driver configuration mediatek this device does not work as accesspoint but turning the network I found drivers modified in github that allow me to enable it as an AP. The driver of the newly installed distro is recognized as wlx00e1b0117ad1 but when I do iw list Supported interface modes: managed monitor there is no AP in the list. If I do iw wlx00e1b0117ad1 scan find me other wifi networks. One of the many guides I follo…

I'm running armbian on an orangepi pc and trying to install freeradius: pi@orangepipc:/$ sudo apt-get install freeradius freeradius-mysql but it spits out this error: Job for freeradius.service failed. See 'systemctl status freeradius.service' and 'journalctl -xn' for details. invoke-rc.d: initscript freeradius, action "start" failed. Setting up freeradius-mysql (2.2.5+dfsg-0.2) ... Job for freeradius.service failed. See 'systemctl status freeradius.service' and 'journalctl -xn' for details. invoke-rc.d: initscript freeradius, action "force-reload" failed. dpkg: error processing package freeradius-mysql (--configure): subprocess installed post-installation script ret…

Hi, guys. I need some help in understanding of usage AR100 (OpenRISC) coprocessor inside H3 SoC for the own real-time tasks. Now i'm using mainline kernel built with RT-PREEMPT patch. I'm using it with Machinekit (LinuxCNC) software to control stepper drivers/motors via GPIO step/dir pulses. But step pulses frequency is too slow (about 17 kHz) because the RT kernel latency is about 30 us. I think we can use the built-in coprocessor for the realtime GPIO toggling. The AR100 and main Cortex-A7 can talk to each other with built-in MSGBox. And the question is - how to launch my own firmware on the AR100 core?

Hello, i have to update nodejs to version 14, but wenn i do curl -sL https://deb.nodesource.com/setup_14.x | sudo -E bash -sudo apt-get install -y nodejs i become this error bash: -d: Ungültige Option Aufruf: bash [Lange GNU Option] [Option] ... bash [Lange GNU Option] [Option] Script-Datei ... Lange GNU Optionen: --debug --debugger --dump-po-strings --dump-strings --help --init-file --login --noediting --noprofile --norc --posix --pretty-print --rcfile --restricted --verbose --version Shell-Optionen: -ilr…

Hello, I have a PineA64LTS I use as a nextcloud server (running on docker). A few days ago, I updated it (for the first time in a loong time) and ended up on a boot problem. Loading, please wait... Starting version 245.4-4ubuntu3.4 Begin: Loading essential drivers ... done. Begin: Runing /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems done. Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... done. done. Gave up waiting for root file system device. Common problems: - Boot args (cat /proc/cmdli…

Hi, I am trying to install TVheadend using Debian-micro-home-server, but no success. Armbian Wheezy with legacy kernel. See printscreen. Any idea? PM

We need you to help us improve THS settings. In case you have a Banana Pi M2+, OPi One, Lite or NanoPi M1 without heatsink and are that experienced to build Armbian images on your own (requires an x86-64 PC/VM running Ubuntu 14.04 or 16.04) or install a new kernel using .debs as outlined below and also want to help developing better settings (less temperatures, more performance in throttling situations) then please read through this whole Github issue here: https://github.com/igorpecovnik/lib/issues/298 If you're not already too discouraged by this stuff then we ask you to build/install a new legacy kernel for Orange Pi H3 or Banana Pi M2+ and ensure /boot/script.bin …

Hello, I thought there is dphys-swapfile so I tried to disable it. sudo dphys-swapfile swapoff sudo dphys-swapfile uninstall sudo update-rc.d dphys-swapfile disable But dphys-swapfile is not installed for swap file. How can I disable swap in armbian completely? Is it enough to just remove this line "/var/swap none swap sw 0 0" from fstab?

https://forum.armbian.com/index.php?/topic/3945-mmc-no-card-present-error-on-allwinner-boards

I have a bunch of UARTS attached to a USB hub, and I need to map them consistent to /dev/ttyUSB[x] I've done some mapping of the ports. but I don't quite know what I'm doing.. any help with some example rules would be great.. here's a sample /: Bus 04.Port 1: Dev 1, Class=root_hub, Driver=ehci-platform/1p, 480M ID 1d6b:0002 Linux Foundation 2.0 root hub |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M ID 05e3:0608 Genesys Logic, Inc. Hub |__ Port 3: Dev 3, If 0, Class=Hub, Driver=hub/4p, 480M ID 05e3:0608 Genesys Logic, Inc. Hub |__ Port 4: Dev 4, If 0, Class=Vendor Specific Class, Driver=ch341, 1…

I know I'm trying to be lazy but why can't we install the PREEMPT_RT kernel from the Debian Bookworm Repositories? eg with: sudo apt install linux-image-rt-arm64. This appears to work but it does not boot into the new RT kernel. Downloaded the deb file and used sudo dpkg-i and it also failed to boot yet this command works if we install a RT kernel we built in the build environment Ran armbian-config and tried to install the kernel but alas its not displayed in the list. Why not? I can pull down Debian Bookworm for the Raspberry Pi from the Debian site and install preempt_rt this way. Why does Armbian make it so hard? …

My goal is to use Radxa Rock3a with a large 3.5inch HDD as a first step. Works fine if I use a M.2 E-key adapter which connects on the PCIe2.0 x1 lane and provides SATA via a JMB 5-port chip (only 2 connectors, support is in U-boot default Armbian build 2024.10). Worked also if I use an overlay included in early 6.1.84-vendor-rk35xx builds that maps RK3568 SATA onto the PCIe2.0 M.2 connector traces/signals, but now the whole 6.1.84-vendor-rk35xx ends in panic. I have not looked at exact changes (it is from the beta channel), but it was working with trunk.x and now installed variant is from trunk.y. I might not be able to find exact numbers for x and …

I am getting a series of errors related to EXT4 zram checksum that look like this one: [3328.749555] EXT4-fs error (device zram0): ext4_readdir:189: inode #11 com find: path var/log/lost+found directory fails checksum at offset 4096 (and other offsets) I've seen a recommendation as a possible fix to the checksum error : disabling metadata_csum, using "tune2fs -O ^metadata_csum /dev/zram0", with the file system umounted (I don't know how to unmount zram) The error apparently is related to bad hardware (not the case) , old kernels that don't support new versions of programs capable of altering the fs. Like a newer checksum feature, or a new…

Hi all, I bought a Orange Pi PC 2 a couple of months back, loaded the Armbian image successfully and tweaked it until it was just right for my application. As this piece of hardware was going to live on a remote property, I bought another 2 Orange Pi PC 2 boards and some new SD cards with the intention of having 2 backups - one for development and the other as spare. I cloned the SD card by copying the active EXT4 partition across to the blank SD card using GParted. The long and the short of it is that these images did not work. I know the hardware is good as the original SD card works in the new OPi PC2 boards. Likewise the new cards don't wo…

Clean Installation of Armbian Stretch mainline kernel 4.14.y to the internal memory of the Orange PI 2018-05-10 09:38:51: (mod_accesslog.c.180) writing access log entry failed: /var/log/lighttpd/access.log No space left on device 2018-05-10 09:39:21: (mod_accesslog.c.180) writing access log entry failed: /var/log/lighttpd/access.log No space left on device 2018-05-10 09:39:22: (mod_accesslog.c.180) writing access log entry failed: /var/log/lighttpd/access.log No space left on device 2018-05-10 09:39:52: (mod_accesslog.c.180) writing access log entry failed: /var/log/lighttpd/access.log No space left on device 2018-05-10 09:39…

Hi, My system has install and setting a lot, wan to read back all of from sd(8GB) card. Actually system capacity around 2GB, using windisk32 to backup image still 8GB So there any way to do image backup and capacity around 2GB. thanks

Hi, Is it possible to install python in armbian OS. Thank you for the answer

Thank you for everything you’ve done. Armbian is amazing. On Raspberry PI devices, it’s possible to pass parameters to the kernel at boot-up and force certain IO pins to go high as soon as shutdown is complete. It’s along the lines of “dtoverlay=gpio-poweroff,gpiopin=xx”. I’m guessing that GPIO-POWEROFF is a kernel overlay, that it’s specific to Raspbian, and that Armbian may have a similar overlay. What’s the best way to discover the name of Armbian’s corresponding overlay, please? That overlay would enable me to configure the relevant single-board computer to send a signal at shutdown, a signal that would cause the charging/power circ…

I've already benchmarked a computer-interactivbe task (like image processing) on the Orangepi 5 plus's processor——and it wrapped up in just 40 minutes, which is impressively fast. Therefore, I' like to try the NPU. Anyone know how to tap into its NPU for AI workloads?