Allwinner sunxi

Hello, I have got my Orange Pi PC+ reading a DS18B20, but it only gives 0.5 degree increments so I believe the resolution is set to 9 bit. This is nowhere near good enough for the application I plan to use it for. When I cat w1_slave I get: 90 01 80 01 1f ff 02 04 5c : crc=5c YES 90 01 80 01 1f ff 02 04 5c t=25000 I have attempted to use this: https://github.com/danjperron/BitBangingDS18B20 but it appears to be specifically for RaspPi. Does anyone know how I can change the resolution to 11 or 12 bit? Many thanks

I have OrangePi Zero and want to use it the following way: 1. OrangePi Zero is connected to internet via Wi-fi 2. on OrangePi's eth0 port is running DHCP server 3. I connect a computer to eth0 port on OrangePi, get IP address via DHCP and access to the internet So internet is provided to eth0 via wlan0. Now, I managed to install dnsmasq, and it is working. Basically my config (/etc/dnsmasq.conf) is: interface=eth0 listen-address=172.16.0.1 bind-interfaces addn-hosts=/etc/dnsmasq/hosts.conf dhcp-range=172.16.0.50,172.16.0.150,12h dhcp-leasefile=/var/lib/misc/dnsmasq.leases IP of eth0 on OrangePi Zero is: ifconfig eth0 …

I have to clear possible blocked interfaces everytime I log on to get access to Internet. I m connected to network but if i dont clear that button i dont get access. Can help me .

I installed the SoftetherVPN using the script provided in Armbian distribution, than I configured it from my windows machine, using the VPN Server manager application downloaded from softether website. When I try to connect from my iPhone I get an error "The L2TP-VPN server did not respond. Try reconnecting. If the problem persists ..." What I didn't do , is opening ports in my router, do I need to forward 443, 992, 1194, 5555 to my BananaPi IP in my router ? Some more details I posted on the softether forum, but it seems there is noone around to answer, and alot of spam is posted daily Thank you. VPN Tools>check Check command …

Hi, I would like to configure my nanopi Air as an AP and facing some issues. I have edit my /etc/network/interfaces as follow to use hostapd # interfaces(5) file used by ifup(8) and ifdown(8) auto lo iface lo inet loopback auto wlan0 iface wlan0 inet static hostapd /etc/hostapd.conf address 192.168.1.1 netmask 255.255.255.0 and I have linked the the hostapd.config config file in the /init.d/hostapd. my hostapd.config is as below ssid=AERS interface=wlan0 hw_mode=g channel=5 driver=nl80211 logger_syslog=0 logger_syslog_level=0 wmm_enabled=1 wpa=2 preamble=1 wpa_passphrase=aerstest wpa_key_mgmt=WPA-PSK wpa_pair…

Hello, I've been trying to use DNSCrypt on ARMBian Debian on OrangePi Zero. I'm following this guide (exact revision link for future reference), and it was working great on Raspbian in Raspberry Pi, When I try the same guide, it compiles, installs successfully, runs the daemon, however it doesn't actually work, saying "connection timed out; no servers could be reached". When I'm not using daemon, and run manually, this time it says "Unable to bind (TCP)". But when I compile and use in Ubuntu, it works nicely. This is my GitHub issue on DNSCrypt repository, including all my tests and inputs: https://github.com/jedisct1/dnscrypt-proxy/issues/561 …

For a lark I wanted to see if a BPi would do as a softsynth. I started with the very nice 2.9 Jessie image* and 4.x kernel, but noticed only then that there's no sound, so I installed the 3.4 packages. After booting, ALSA seems to be working fine wrt line sound output and mixer. I could also play MIDI files with fluidsynth fine and hear clear audio on headphones. Connecting a USB MIDI keyboard also gets detected and its ports show up. Now, fluidsynth as a server won't start and neither does jackd. Both seem to complain about missing /dev/snd/seq. So I'm wondering if there's a kernel module or option missing or if it's an artifact of there being no actual MIDI synt…

I am successfully using Armbian Current on my Banana Pi. I have a 120GB usb SSD drive. I'd like to boot from it - my other Banana Pi with the same system boots from SATA connected HDD no problem. When I boot the device, I can see the drive using sudo fdisk -l as /dev/sda1 I can also get the UUID and everything. I've modified the /boot/armbianEnv.txt file and changed the UUID, but I can't get the machine to boot. I tried also to change the UUID to /dev/sda1. Didn't help either. When I boot with HDMI connected, I can see the kernel iterating through USB bus and the result is "no USB storage device found" and that's it. …

Hi, I have serious problems with the 5.25 images of armbian on a cubietruck. After a fresh install and apt-get update apt-get upgrade I get errors with : dpkg: error processing archive /var/cache/apt/archives/linux-libc-dev_4.4.0-78.99_armhf.deb (--unpack) This is for the Armbian_5.25_Cubietruck_Ubuntu_xenial_next_4.9.7 image, with other images this concerns a different package. Only Armbian_5.25_Cubietruck_Ubuntu_xenial_default_3.4.113 works. After this error, the filesystem seems to be defect and is remounted ro. On another try, I removed the rmount ro on error option from the fstab and the /var/lib/dpkg directory was corrupted. …

I'm running a web cam on a OrangePiOne. For the last four days its been performing adequately, at least as well as the RaspiPiZero. At the moment though its suddenly decided to become a snail... slower than paint drying or melting blanc mange. So here I am looking for pointers. I don't have a lot of detail, but what I have follows. I'm using mjpg-streamer to handle the webcam. In the past this has been rock solid without issue, at this point I assume its not the problem in itself. Architecture: armv7l Byte Order: Little Endian CPU(s): 4 On-line CPU(s) list: 0-3 Thread(s) per core: 1 Core(s) per so…

I installed the image https://dl.armbian.com/orangepizero2w/Bookworm_current_minimal on my Orange Pi Zero 2W board. But when I tied to check sound from the headphone interface on the expansion board I have a problem: user@orangepizero2w:~$ aplay -l aplay: device_list:274: no soundcards found... There is no chance to turn it on even through DTB overlay in armbian-config because there is no sound card in there. How to make sound work in this board with Armbian?

hi im newbie OrangePI, how to make WiFiUSB work Bus 002 Device 002: ID 148f:7601 Ralink Technology, Corp. I try this step https://github.com/pvaret/rtl8192cu-fixesbut get error on this cmd sudo apt-get install git linux-headers-generic build-essential dkms root@orangepipc:~# git clone https://github.com/pvaret/rtl8192cu-fixes.git Cloning into 'rtl8192cu-fixes'... remote: Counting objects: 438, done. remote: Total 438 (delta 0), reused 0 (delta 0), pack-reused 438 Receiving objects: 100% (438/438), 1.80 MiB | 240.00 KiB/s, done. Resolving deltas: 100% (223/223), done. Checking connectivity... done. root@orangepipc:~# sudo dkms add ./rtl8192cu-fixes sudo: dkms: …

Hello, I received a few weeks ago some new Lime2 boards. Using compiled Armbian kernel leads to a network problem: no IP is set and network does not work I have messages when connecting Ethernet cable: sun7i-dwmac 1c50000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx Link is Up - 100/Full The ip a command gives: 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000 link/ether 02:02:02:cc:cc:cc brd ff:ff:ff:ff:ff:ff inet6 fefe::fe:xxx:xxx:9307/64 scope link valid_lft forever preferred_lft forever I think the problem is related to the new revision of the board as described here…

Greetings, after a long time I am playing with my old Banana Pi Pro again. This time with the intention to probably use it on IoT purposes. That implies I only need WIFI and the GPIO pins. Which gives some opportunity to save power by powering down every thing else which is not needed. My first approach here is to strip down everything from the device tree I don´t need. That means everything related to: framebuffer hdmi lcd sata display engine ethernet video codec usb ir gpu/mali That resulted in a drop in power consumption in idle from: ~0.990 - ~1.330W to: ~0.700 - ~1.000W …

So, here is the problem: I'm running the latest version of Armbian buster on an Orange PI PC+2E and as you know this piece of crap doesn't even support a proper shutdown function: all what is does is "reboot: system halted" and the screen remains on. Is there a way to turn the screen off (at least) after system halted? maybe a script that runs right before shutdown ? I've reas several discussion but non of the solutions worked

Hi there. @Moderators: sorry for double-posting, started here: https://forum.armbian.com/topic/13916-cubietruck-allwinner-a20-spidev-no-such-device/?do=findComment&comment=101122 but might be the wrong section and been overlooked by "cubietruckers". Feel free to delete the one over there. @Moderators: could you verify my account please so that I can edit my posts after posting on the same day? I'm human, I can tell traffic lights from trees, cars, and trucks ;-) Cubietruck. Stock image 20.02. apt-upgraded to 5.4.35-sunxi EDIT: NOTE: just checked the armbianmonitor upload result, which says "5.4.20" at the top - but "…

I was wondering if anyone could help with the following issue, We are working on a project utilized with an Orange Pi Lite, ALLWINNER H3 processor and Armbian stretch mainline kernel, Now we are bundled a chip over GPIO, due to the chip frequency we looking for a library or setting file to modify and match I2C frequency with the chip, BR,

Good evening. I've just installed Armbian in a OPI +2, in a 32 Gb card. The OPI is connected by LAN to my router, in the same way the PC I am using to write this message is. But "Wicd Entwork Manager" says : - "not connected" after "Obtaining IP address" if using wire-default profile. - "done connecting" after "setting IP address " id using a fix IP address setting profile, but in fact, there is no connection. Has anybody faced something like this ? Any idea ? Best regards. maesstrissimo

Hi, I have probably trivial question related to GPIO on Orange Pi Zero. So - I have a switch there connected ot 3.3V and then to GPIO (pin 12 on Zero). What I want to do is just to read GPIO state. When button pressed it goes to high state - normally. On RaspberryPi and Odroid C1 that works fine just using basic code with wiringpi2 or eventually wiringpi. So I tried the same on Zero compiling wiring for H3/H2. My code is basic in Python: import time import wiringpi import pyA20 as GPIO cykl = 1 wiringpi.wiringPiSetupGpio #or wiringPiSetup() wiringpi.pinMode(1,0) while cykl == 1 : do_call = wiringpi.digitalRead(1) if do_call: print 'pressed' time.s…

Hello. I have a annoying problem each time i burn with 'dd' a armbian*raw image (custom) in linux my orange pi lite not boot, i must format and write in windows (write32...) then works. any idea? [ 998.313215] usb 3-7: new high-speed USB device number 6 using xhci_hcd [ 998.443018] usb 3-7: New USB device found, idVendor=058f, idProduct=6331 [ 998.443026] usb 3-7: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 998.443030] usb 3-7: Product: Mass Storage Device [ 998.443033] usb 3-7: Manufacturer: Generic [ 998.443036] usb 3-7: SerialNumber: 058F091111B [ 998.443733] usb-storage 3-7:1.0: USB Mass Storage device detected [ 998.446321] scsi host…

I'm sorry if I come across as incompetent but I have limited skills in linux and I really dont know where else to turn to. I recently bought a DVB-S reciever to plug into my SBC (banana Pi M1) to use with tvheadend, as opposed to getting a dedicated chinese box. I just cant seem to get it to work! This is the Tuner I bought: https://www.linuxtv.org/wiki/index.php/Geniatech_HD_Star_DVB-S2_USB2.0 Apparently I have revision 3 of the board: http://imgur.com/3IhpuGG This is the comparison between the lsusb in the wiki, and my board: http://imgur.com/iHN3R5R This is the output of dmesg: [ 7.847279] sun4i-ss 1c15000.crypto-engine: Die ID 0 [ 7.911683] dw2102…

Dear all, i just installed a fresh Armbian 4.5 Jessie with Vanilla kernel 4.2.3 on an SD card and booted it on a cubietruck. I did not receive any HDMI output. This did not change after a kernel update to 4.2.5 via apt-get update and apt-get upgrade and a reboot. However, the same cubietruck works flawlessly with Debian Wheezy (2.6 updated to 4.5) and kernel 3.4.110. I checked the boot.cmd script and looked into cubietruck.bin - the standard settings would appear to identify the correct (HD) display resolution and to enable HDMI by default. Do you have any recommendations ? Is there anyone experiencing the same problem ? With kind regards, Lupus …

I am trying to connect a SNBC receipt printer to my Banana Pi - model number: BTP-r580(II) However, dmesg shows that whilst it is identified as a USB device, it is not identified as a printer (probably not helped by the fact that all of their receipt printers appear to have idVendor = 0x154f and idProduct = 0x154f Whilst their website (http://www.newbeiyang.com) has downloads for linux drivers, once connected there is no /dev/usb nor a dev/ttyUSB0 directory (in case it is recognised as a serial device). The linux drivers appear to be used for CUPs which is not installed, so I have not downloaded them. Someone else has the same problem on the Raspberry Pi wi…

Hello, I'm running a freshly installed armbian with mainline kernel 4.9.5 on my cubietruck. Between u-boot messages and login prompt I don't get any output while booting. I've tried several values for the "console" parameter in the armbianEnv.txt and recompiled the /boot/boot.scr file without success. I've tested both VGA and HDMI (with an HDMI to VGA adapter) outputs without success too. What should I do to get things to work please ? Thanks for your time and your great work on armbian.

Good morning all I have an OPi Zero H2 with the official expansion card. My goal is to make an Airport module to connect a speaker to it. The installation of Shairport in APT all is ok I can see the sharing on my iPhone. But the problem is that I have no sound when I plug a speaker into the 3.5mm jack port on the expansion card. I have correctly installed the "analog-codecs" and made a reboot. In Alsamixer I put "Line-Out" and "DAC" to the maximum (red). But still no sound ... When in doubt, I did all these operations on Armbian Focal / Buster / Bionic but it didn't change anything. Can you help me please? believe me I have tried everything for 4 da…

hello everyone ! How to get totally permission in /root folder of my orangepiplus2 under armbian? I have already set sudo su ----pass ok I'm installing WiringOP and I have to go inside /root Using psw I know the path that is /root/WiringOP Then I type chmod +x /.build and then /.build but I don't have permission . Opening the file system I see the "X" over the root folder Could I have the totally control of armbian ? Thanks !

Hello there, Some time ago there was a note about "no sound in M2" and what about present time? Just tried 5.24 and still: root@bananapim2:~# lsmod Module Size Used by evdev 9348 0 ir_lirc_codec 4088 0 lirc_dev 6245 1 ir_lirc_codec sunxi_cir 3159 0 sun4i_ts 3350 0 sun4i_ss 13314 0 uio_pdrv_genirq 2780 0 uio 6272 1 uio_pdrv_genirq cpufreq_dt 2856 0 sun4i_codec 10232 0 snd_soc_core 97900 1 sun4i_codec snd_pcm_dmaengine 2770 1 snd_soc_core snd_pcm 57610 2 snd_pcm_dma…

I'm trying to configure the RTL8189FTV module on an Orange Pi+ 2E in SoftAP + STA mode so I can use it as wifi hotspot. According to this old document from Realtek (http://www.ofeixin.com/downloadRepository/8da8dda7-6721-4ac8-a7db-47cc4d9b218c.pdf), it's possible to do so using an RTL8189ETV, so I'm assuming it's possible on the RTL8189FTV, too. The default driver doesn't allow concurrent connections like this, tho, so it must be recompiled. I downloaded the source recommended on the sunxi wiki (http://linux-sunxi.org/Wifi#RTL8189FTV): git clone https://github.com/jwrdegoede/rtl8189ES_linux.git cd rtl8189ES_linux git checkout -B rtl8189fs origin/rtl8189f…

Hi, I've got a quick question regarding the kernel upgrade instructions on a Cubietruck that runs on Igor's Debian image. Let me mention first that the system boots from my Cubietruck's NAND. However, the root partition and the /home partition are both installed on some SSD. I've followed the instructions about the kernel upgrade (3.4.106-cubieboard to 3.19.6-cubietruck) in order to be able to use the proper shutdown feature - as detailed on http://www.igorpecovnik.com/2013/12/24/cubietruck-debian-wheezy-sd-card-image/. I.e. I installed the various *.deb packages which were contained in the *.tar archive via `dpkg -i`. Then I ran the steps as desc…

Hi, we've been running 5.31 with VDPAU support for a long time now, and I've tried to "apt-get dist-upgrade" to newer version of Armbian. With 5.31 VDPAU works well, with 5.38 all calls to vdp_imp_device_create_x11() fail with "Error when calling vdp_device_create_x11: 25" Demonstratable on "vdpauinfo" Spoiler # Armbian 5.38 # DISPLAY=:0 VDPAU_TRACE=1 vdpauinfo display: :0 screen: 0 VDPAU capture: Enabled vdp_imp_device_create_x11(0x9c7f10, 0, -, -) -> 25 Error creating VDPAU device: 25 # Armbian 5.31 # DISPLAY=:0 VDPAU_TRACE=1 vdpauinfo display: :0 screen: 0 …

Hi, Running on Armbian_community 24.8.0-trunk.529 Bookworm with Linux 6.6.43-current-sunxi64 onthe orangepi zero3 And need to use the GPIO pins with python, not an expert here but have tried a few recommandations with no luck. Can anyone suggest method that works with the above OS/build please? Thanks! Rob.

how i can enable usb wifi on orange pi pc ?

Hi! I love this Linux distribution, I have tried some months ago and had worked very well. Now, I want install armbian in a pdduino3b, I go to "downloads" select pcduino3, and I have two options: Xenial_server_vanilla and Xenial_server_legacy. I want hardware acceleration and most options of drivers and compatibility possible, so, I go for legacy option. But I realize that the two images have not a desktop environment, this is true? If yes, where can I download the full newer armbian version with legacy kernel and desktop ready? I try install xcfe over legacy image, but I have found for errors like "screen not found" and others... Regards.

I'm getting an error and I'd like some feedback if it is a missing package (apt-get) or a bug in OctoPrint or something wrong in Python. It looks like something is blowing up with Python trying to install a package called scandir 1.3, but I'm not getting anything when I google it with the error. Thoughts? The documentation on Git was up to date... the documentation on Octoprint.org is wrong for building it from source. Error: creating 'dist/OctoPrint-1.3.0-py2.7.egg' and adding 'build/bdist.linux-armv7l/egg' to it removing 'build/bdist.linux-armv7l/egg' (and everything under it) Processing OctoPrint-1.3.0-py2.7.egg creating /home/admin/OctoPrint/venv/li…

Welcome to Armbian Bionic with Linux 5.4.20-sunxi This is the thing I have installed... I'm trying to use the serial ports out of the GPIO header, nominally pins 8 and 10 which depending on what you read maybe ttyS1 or ttyS3. Out of the box whatever they are they're not available. After much googling, I've seen stuff about FEX and DTS none of which mean much to me, I'm guessing Bionic doesn't use FEX as there's no sign of .FEX or .BIN files in the /boot directory. The default state seems to pump garbage out the tx line whatever its doing. Minicom promises to talk to any ttyS? I give it, but theres no answer on loopback, And that's all I have. …

Hello, I don't know if this is board related or probably armbian related... anyway. In my old banana pi (4.19.13-sunxi) htop (version 2.1.1) is like this: While on every other linux PC, server or whatever I have it looks like: The small and stupid difference is in those blue "tree view" lines (under the Command column), which I don't really like nor understand. Is there a way to set those lines as they normally should be? (and why was it set???) Thanks

Hi all, Igor: I wanted to say many thank you and congratulate for the awesome job you made with armbian! I have a little big problem: I'm using the BPI-R1 (a.k.a. Lamobo R1 Linux version 4.2.0-sunxi (root@kitchen) (gcc version 4.8.2 (Ubuntu/Linaro 4.8.2-16ubuntu4)) but out of the blue I got the well known problem of the RCP reset to the 1970. I followed the instructions reported here https://github.com/igorpecovnik/lib/issues/111#issuecomment-145634651 but I got some strange issues 1) If I plug my USB keyboard I cannot interrupt the boot process to get a shell before the kernel loads. 2) If I change my boot.cmd and update the boot.scr settings with verbosity=9 an…

I am trying to switch legacy kernel to "next". I did it successfully with armbian-config for OrangePiPC (obviously Armbian was installed on SD card). Once I attempted to do the same with Orange Pi Plus and system installed onto internal EMMC then after reboot... nothing. I am wondering also if the issue is related to platform or the fact that Armbian was installed on EMMC. I have connected TTL2USB and following is the result (seems to be indefinite loop): U-Boot SPL 2017.11-armbian (Jan 25 2018 - 07:58:02) DRAM: 2048 MiB Trying to boot from MMC2 U-Boot 2017.11-armbian (Jan 25 2018 - 07:58:02 +0100) Allwinner Technology CPU: Allwinner H3 (SUN8I …

The Orange Pi Zero Plus has only a CVBS/FBAS/RCA video output, therefore I believe that only a televison but no VGA or DVI/HDMI monitor can be used (or headless use). Has anybody an idea how to convert CVBS to VGA or DVI/HDMI? L.

Hello to All! The systeminfo after login does not show up anymore!!! What might be the problem and where to look for fixing it ?? Regards, Ireng

Hey guys. I have been trying to utilize H5 vpu decoding for 10+ hours... Still no go. Here is the checklist: kernel Using mainline kernel 5.8.9 from Armbian/build current. `uname -a` output: All kernel configs needed on Sunxi-Cedrus homepage were added, cma set to 256M. libva-v4l2-request Using https://github.com/Sash0k/libva-v4l2-request master. Compiled and make installed. `vainfo` output: `v4l2-ctl --list-formats` output: `./v4l2-request-test -f 25 -l` output: Cpu usage is quite low(4 cores <5%), checked with lsof and…

Hi all I need a bit of assistance in installing OpenMediaVault on the Cubietruck. I'll admit I tried this a while back, so I'm coming back to this to try and use my Cubietruck as a mini NAS. Tried to install using the instructions over at the debian site, but after the install, the web interface showed lots of errors and it wouldn't work. Done lots of googling to try and find further information but I'll admit I'm a bit vexed. Does anyone have some idiot-proof instructions or a prebuilt image they could provide to a bit of a linux newby? thanks in advance -matt

How enable UART1 (pin 8 and pin 10) or UART2 (pin 11 and pin 13) I re-read a lot of documentation but did not find a solution, everyone writes abstractly. There is a concrete decision how to include it for orange pi (zero or one) and armbian. Correctly I understand that UART1 is ttyS1 and UART2 is ttyS2?????? p.s. Help, I'm ready to even pay for help ) uname -a Linux orangepizero 4.11.5-sun8i #11 SMP Fri Jun 23 20:03:23 CEST 2017 armv7l GNU/Linux

Hi, thank for your work i need to make a hotspot with cubietruck I test all debian images for cubietruck but impossible Configuration - connexion VGA - ethernet connected - microsdcard 16G sandisk ou 32 g - clavier with doogle usb all image is dowload today ** Cubietruck_Debian_3.7_jessie_4.0.3 last message Welcom to Debian GNU/Linux 8 (jessie)! [TIME] Timed ou waiting for device dev-ttyS0.device. [DEPEND] Dependency failed for serial Getty on ttyS0. ** Cubietruck_Debian_3.7_jessie_3.4.107.raw Cannot Display This video mode ** Cubietruck_Debian_3.7_wheezy_3.4.107.raw Cannot Display This video mode ** Cubietruck_Debian_3.7_wheezy_4.0.3.raw ... fai…

Hi, I have a BananaPi Pro with A20 cpu. I try to install Motion and Motioneye but it fails. I found some tutorials but nothing worked for me. Is there any proper tutorial about how to install it? Thanks.

Hi! So the problem is when I configure wifi hotspot using hostapd, isc-dhcp-server, and ifupdown, I'm able to start the AP, connect to it, and ping. However, the moment any device connects to the AP the serial console gets spammed with this message around once a second: protocol 0000 is buggy, dev wlan0 This happens on the unofficial Armbian build (from the Armbian OrangePi Zero3 page), DietPi, and the official OrangePi Debian build. The wireless band doesn't matter. Kernel version: 6.1.31-sun50iw9. I tried to set up the AP with NetworkManager, but couldn't manage to connect to it. Probably DHCP issues that I couldn't resolve. I haven't …

I'm having trouble porting some WiringPi programs to my NanoPi Neo. I have an original neo v1.0 running the latest armbian stretch (as of Oct 04 2018). Have tried several, including mstroh76/WiringNP, and can compile, but programs hang when executed. I'm okay if this is the deep-end of the pool but I wanted to verify that I an indeed in deep waters or if I'm doing something dumb and really in the shallow waters and all I have to do is stand up to get my head out of the water. Which WiringPi library should I be using for C language programs on a NanoPi NEO v1.0 running a recent Armbina Stretch release?

Hi, I successfully installed owncloud on the Cubietruck. Because of owncloud, I decided to give jessie a try, since there are more packages I need already included. Got all that working. Now, I wanted to make the Cubietruck into a wireless AP following the instructions in the FAQ on Igor's blog. However, i am getting nowhere. After boot, hostapd seems to be running: ps -elf | grep hostapd 1 S root 677 1 0 80 0 - 1040 poll_s 18:25 ? 00:00:00 /usr/sbin/hostapd -B -P /run/hostapd.pid /etc/hostapd.conf However, the SSID is not picked up by any client, so it seems as if it is not braodcast. However, it is not hidden either, since I cannot …

Hello I have an issue with my HDMI display. Some of the desktop is out of screen. This is about 3% or 15px all around the screen. Changing resolution from 1080p down to 720p and down to 800x600 doesn't fix the borders. Armbian-config allows me to edit the booting environment. Atleast these lines won't work: disable_overscan=0 .... this can also be 1 with no effect overscan_x=-30 overscan_y=-30 .... these can also be positive with no effect also overscan_top, overscan_bottom, overscan_left and overscan_right don't work Only line that changes something is the one with resolution: disp_mode=800x600p60 I don't have zoom on this display or I have l…

Hello, and sorry for my English. I install in my orange pi lite the armbian, but I can't config my TFT 7" correctly. The problem is that part of de left size of the screen is hidden and the botton size also. I tray to config with h3disp but depence of the config nothing happens or the screen became red. If I connect by ssh all is correct only is when conect the hdmi. Thank you

Hi, is it possible to have the serial/UART on the Olimex LIME2 to work as a serial console on Armbian Jessie (kernel version 4.5.2)? The UART is already working during early boot, but once kernel is loaded it becomes inactive. /boot/boot.cmd contains: setenv bootargs "console=tty1 root=/dev/sda1 rootwait rootfstype=ext4 sunxi_ve_mem_reserve=0 sunxi_g2d_mem_reserve=0 sunxi_no_mali_mem_reserve sunxi_fb_mem_reserve=16 hdmi.audio=EDID:0 disp.screen0_output_mode=1920x1080p60 panic=10 consoleblank=0 enforcing=0 loglevel=1" Thanks

Hm.. I'll write to you what I have done. Please tell me what's wrong. I have a cubietruck, and I downloaded this one, Legacy Jessie(http://mirror.igorpecovnik.com/Armbian_5.00_Cubietruck_Debian_jessie_3.4.110.zip), and installed it. Install was successful, and worked good. I tried to use nand and SD, and SD only. There were no differences. The result that I want to tell you below, is the same on both cases. ......................... After OS install, I followed this instruction, and I installed several packages. Instruction : wget -q -O - http://upgrade.armbian.com | bash Packages : NFS server Samba server Deluge Daemon(server) I have a 3TB sata disk …

Dears, We have 4 boards Nanopi Neo2, but when we connect to energy, they don't boot, leds of net port (green and yellow ones) and internal led (red) are on all time. We tried to access via serial port (using an usb-serial adapter), but they not show any boot process. We tried some different boot images on sd card. Nothing works. All four devices are in this situation (and they are new!). There is any thing we can do?

Hi!!! I am planning to buy Orange Pi PC but I saw that it has thermal issues because of overclocking/overvolting. My question is, Is armbian able to fix this problem??? ------Sorry...I am new to Single Board Computers----- Another thing, If Armbian isn't helpful about it, Does Orange Pi PC2 differ from it's predecessor??(I mean in thermal issues)... Thanks To You!!

Hi, has anyone been able to use the BPi 7 inch LCD (S070WV20-CT16) with Banana Pi M1+? I took the FEX file from this how-to: https://sinovoip.blogspot.hu/2015/08/how-to-banana-pi-bpi-m1-7-inch-touch.html and put it the "bin" subdir of the Armbian image (Armbian_5.20_Bananapipro_Debian_jessie_3.4.112_desktop.7z), then symlinked from the script.bin in the root dir to it (I did not change anything else in the image) and rebooted. At boot when it comes to starting the kernel, it always resets (starts the boot process again and again). When I use (symlink to) the "built-in" bananapim1pluslcd7.bin in the image, the same result: starts the boot process again a…

I'm trying to set up my OPI PC+ with a static IP address on wlan, but it doesn't seen to be working. This is my /etc/network/interfaces file: allow-hotplug wlan0 iface wlan0 inet static address 192.168.25.160 netmask 255.255.255.0 gateway 192.168.25.1 dns-nameservers 8.8.8.8 8.8.4.4 wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf I tried both with wpa supplicant line commented and non commented, but every time I boot up the board, it is still with the DHCP address.

Hi, I was just wondering if anyone else out there with a Win+ has this issue .... when I install from an image file all works well, WIFI etc all good. But when I upgrade the install wlan0 etc has gone. ifconfig doesnt show it, lsmod shows the brcmfmac/cfg80211 I've tried it with a few of the recent image files systemctl status systemd-modules-load systemd-modules-load[1693]: Failed to find module 'lp' systemd-modules-load[1693]: Failed to find module 'ppdev' systemd-modules-load[1693]: Failed to find module 'parport_pc' root@zoot: lsmod Module Size Used by ipt_MASQUERADE …

From the armbian page, i downloaded and installed the... Armbian Stretch mainline based kernel 4.19.y Server or light desktop usage scenarios. High level of software maturity ...for my orangpiplus2e. I was able to create the login and password and get sudo powers. But the screen does not go to the GUI, it just stays at the CL. I log in to the 'tty1' login with u and p. I get the "general system configuration beta: armbian-config]. After that it says "host@server: ~$ I don't know what to do next, if anything, or if it is supposed to automatically take me to the GUI desktop. It does not seem to be connected to the interne…

What happened? Orange Pi 3 LTS rarely recognize ethernet connection. How to reproduce? Flash Orange Pi 3 LTS with an image of the latest version of Armbian. Extra Info The latest images tested which worked flawlessly was: Armbian_community_25.11.0-trunk.437_Orangepi3-lts_trixie_current_6.12.47_minimal.img Armbian_23.8.3_Orangepi3-lts_jammy_current_6.1.53_minimal.img Images tested which didn't worked: Armbian_community_26.2.0-trunk.151_Orangepi3-lts_trixie_current_6.12.63_minimal.img Armbian_community_26.2.0-trunk.100_Orangepi3-lts_trixie_current_…

Two days ago I upgraded the kernel to 25.5.1 (6.12.30-current-sunxi) from 25.2.3 (6.12.20-current-sunxi). Since then I have no longer been able to play a certain title (FLAC file) in mocp. In case it's relevant, the title is: "Malukah - Awake (The Dragonborn Comes)". Symptoms: dmesg starts showing kernel trace output at 1:43 of the song mocp finally stalls at 1:52 and it's impossible to interact with it from that point on Is there anyone here who would be able to provide pointers on how to debug this? I am a developer and I have done some work with Yocto/OE before and wouldn't be afraid to get at this with a debugger. Since it's nice…

Hi, I would like to put ip cameras into the grid as you can see here: omx cctv Does the armbian support omx player? Or is there another solution for grid view ? Hardware: Orange pi One

Hi, I'm trying to install Armbian 5.20 vanilla kernel to eMMC on my Opi PC+. After nand-sata-install finishes I shutdown the Opi PC+ and power it back on. At least, I enable the power, I don't see anything happening in minicom on my pc. Only when powering it with a microsd in the slot (with armbian) will the uboot show in minicom on my pc. Doing a nand-sata-install with 5.14 legacy worked. What am I doing wrong (especially seeing nothing after a reboot with my ttl-to-usb connected is a bit strange for this noob)?

Good evening, In your opinion, what is the best alternative to the NanoPi NEO2? I don't need wifi or sata. I'm looking for a stable and qualitative armbian with a gigabit and usb port. Is there a better performing armbian that the NEO2 has for less than 40$? Thanks

I have an issue with armbian installed oPI PC+. I have it in a case with a cooling fan installed and connected to 2 GPIO pins. My question is: could the cooling fan connection be the cause for my oPI PC+ won't shut down from the power supply and keeps running in the background after i shut down armbian? Any suggestions, I haven't tried starting without the cooling fan yet.

Hi guys, I tried to disable console output on uart0 using this guide https://docs.armbian.com/User-Guide_Fine-Tuning/#how-to-toggle-boot-output But I still get boot output on uart0. Problem is, that I'm using uart0 for a java application. Java application crashes a few seconds after starting. I got the hint, that I should disable console output on this port, to make it working. See here: http://pi4j.com/example/serial.html I think that's the problem, because if I unplug my serial device from uart0, java app doesn't crash. I'm using Banana Pi. Kernel is Verison 4.8.12. Armbian is Jessie 5.24 with desktop. How can I disable the output? Yours, Martin

I'm trying the Orange Pi PC for a smal project but while installing th OpiPC corrupts its SD Card. Typical error occurence: - Install Debian Jessy server on 16GB SD Card (ScanDisk Ultra class 10). - run first bootup. - update und upgrade software, install nfs-common and rrdtool. - setup keyboard, console-setup, tzdata, locales, static ip. - edit /etc/fstab, mount nfs-volume. - copy project software (mostly bash scripts, reading cpu temp and switching GPIO-Pin). - seting up a cron job. on one of the next shutdown/reboot the console shows mmc errors while reading and writing (see log file). - the Sd card can not be started any more, all attempts fail with mm…

I have an Orange Pi PC Plus and I'm looking for a USB video grabber. Could you suggest me some models which are easy to setup and work with OPi reliably?

After the automatic update to kernel 4.19.17 the CPU temperature is wrong and much higher, also in dmesg there are these errors Spoiler dmesg | grep thermal [ 6.428747] thermal thermal_zone1: binding zone cpu-thermal with cdev thermal-cpufreq-0 failed:-22 [ 6.841480] thermal thermal_zone0: failed to read out thermal zone (-110) [ 6.841546] OF: /thermal-zones/cpu-thermal: arguments longer than property [ 6.841560] thermal thermal_zone2: failed to read out thermal zone (-110) [ 7.877181] thermal thermal_zone0: failed to read out thermal zone (-110) [ 8.050346] thermal thermal_zone2: failed to read out thermal zone…

http://www.orangepi.org/OrangePiR1/ Not sure how different it is from Zero other than the second ethernet port and new RTL8189FTV wifi. I'm waiting for a low cost dual ethernet box for a long time. Ordering now.

Hello ! I know that there are already topic talking about that, but they didn't helped me. I have Armbian 5.38 Desktop. I plugged the camera, and I think it's on the right side: I followed instruction of Garlic here: Nevertheless, with motion I get a grey screen telling me that the camera is undetected: I noticed a very small impact on the cable after the delivery of the camera, but because it is very small, I don't think it's the cause. I don't understand, and any help is welcome. Thank you !

Hello, I have problems with the armbian distributions on my orange pi zero 3 because I can't even use chatgpt to activate the sound card on the expansion board that comes as an accessory for the orange pi zero 3. I'm referring to the board that has two USB outputs and an audio jack port that I think is also a video port, but I can't get sound out of that port, only sound comes out of the HDMI port. It's a real mystery since there's no problem with the other distributions, but with armbian I can't get that audio output port to work. If you can help me please, I've tried a number of things and I can't get it to work.

Hello, I am new to armbian and am quite impressed of the ease of installation and use. I copied the vanilla headless Debian jessy to a spare SD and the board booted right away. So first of all, many thanks to the developers! I rely on GPIO for my application of the board, so I first tested the export of a GPIO. Normally, the kernel from Olimex gives me something like "gpio64_pg0", which is not very compatible to the programs out in the internet (e.g. OpenHAB.org which I use), so – with this kernel – I was happy to get a standard "gpio1" when echoing "1" to "export". But as soon as I tried to change the direction echo out > gpio1/direction the whole board…

I'm pretty new to Linux, so it could just be me doing something wrong, but I downloaded Armbian_5.34.171121_Orangepiplus2e_Ubuntu_xenial_next_4.13.14_desktop.img, put it on an SD card, and load it in the orange pi. The legacy installs fine but not this version. Before I even make it to the login prompt I get these codec errors: sun4i-codec 1c22c00.codec: ASoC: /soc/codec/analog@01f015c0 not registered sun4i-codec 1c22c00.codec: Failed to register our card Then after filling out the login info, adding a new user, it goes to boot to the desktop, but nothing happens, just returns me to the command line. After some mucking aro…

Hi friends! Here is the situation. Trying the armbian jessie 3.4.109 and 4.2.3. When installing a new soft it takes to much time. For example, when running apt-get upgrade after fresh image install, it takes about 17 minutes. Of course it contain the core update. But that upgrade part on jessie takes about 7min, on wheezy about 3min. The same thing when just install some software, like apache2 or mc. It takes to much time (for mc it takes about 1 min on jessie, about 30sec on wheezy). The same with reloading. It takes about 1min. Situation is the same on both jessie 3.4.109 and 4.2.3 Tried the same with Banana PI. The same thing. I use the fastest SD card. …

I did try the latest Armbian 23.5 Bookworm on my banana pi m2 zero with allwinner h3 chip and I couldn't get the USB OTG port working (i. e. no keyboard recognition) and eth0 also did not work. After a lot of searching I found an old image (BananaPi-M2zero_Armbian_2021.08.1_bullseye_CLI_5.10.60.img) which did work. I wonder what happened to the kernel Kernel 6.2.y edition and why those crucial hardware features are not working anymore. Is there a vault somewhere of older armbian software revisions?

Dear Armbian Friends, My temperature sensor is not detected by board. Can somebody give me some advice what should I chceck / change / test now? Cheers! Lucas I tried: - another sample of DHT11 - changed cables to different ones - changed - both tested sensors were connected with 4.7k resistor between positive and data cable - tried different system versions like bionic, stretch and now jessie - tried to load modules via /etc/modules-load.d/modules.conf g_serial w1-sunxi w1-gpio w1-therm - or with /boot/armbianEnv.txt (disabling loading with modules.conf) wverbosity=1 logo=disabled co…

I'm working on a Duo project that needs SPI and this is how I configured and tested it without the mini shield. Requirements: NanoPi Duo with test Armbian image 1 female to female jumper wire Enable SPI on boot: sudo nano /boot/armbianEnv.txt Add spi-spidev to overlays= Add line param_spidev_spi_bus=1 sudo reboot If everything worked you should have /dev/spidev1.0. Check with ls /dev/spi*. Now we can test with a C program: cd wget http://www.raspibo.org/renzo/spidev_test.c gcc -o spidev_test spidev_test.c sudo ./spidev_test -D /dev/spidev1.0 spi device: /dev/spidev1.0 spi mode: 0 bits per word: 8 max speed: 500…

I'm trying to run an executable on an OrangePi Prime. The message is: -bash: <filename>: No such file or directory The output of the file command on the executable is: <filename>: ELF 32-bit LSB executable, ARM, EABI5 version 1 (GNU/Linux), dynamically linked, interpreter /lib/ld-linux-armhf.so.3, for GNU/Linux 2.6.32, BuildID[sha1]=xxx, not stripped The app runs fine on OrangePi One, OrangePi Zero and Raspberry Pi.

Dear mainline developers, I'm writing a (mainline) SPI driver for de ads131 from TI which I would like to make use of DMA, on the orangePIzero H2, zero+ H3/H5 and nanopi NEO2+. On the 4.13.3-sunxi kernel (armbian 5.33), this works fine, the driver is automatically loaded when the associated devicetree overlay is loaded, and the DMA can be allocated. However, when I compile the same driver for newer kernels (4.14.17-sunxi, 4.14.39-sunxi, 4.14.67-sunxi armbian 5.59), the dma allocation no longer appears to work, while the SPI part of the devicetree is identical except for the phandle (checked with dtc -I fs /sys/firmware/devicetree/base on newest 4.14.67-sunxi kerne…

Hello everyone, This is my first post, but i've been using armbian for almost one year (https://twitter.com/logicite/status/682267764384501760), so : thank you for your work ! I use armbian ubuntu on Olimex A20 lime 2, and on LeMaker Banana Pro. So far no difficulty, or i was able to find the answers on the forum. This time, i can't find anything, so i'm asking for your help : A few months ago i was able to use the onboard sound card on the BananaPro. It was showing up in alsamixer and in aplay -l. The sound was not good so i used a USB sound card instead. Today, i can't find this onboard sound card any longer. I suspect this is due to some update in …

Hi I try use Nokia 5110 with Orange pi zero. I found this library: https://github.com/rm-hull/luma.lcd and try to run it on my orange pi with this tutorial: http://codelectron.com/interface-nokia-5110-lcd-and-raspberry-pi-python/ so in python shell I add these: >>> from luma.core.interface.serial import spi >>> from luma.core.render import canvas >>> from luma.lcd.device import pcd8544, st7735, uc1701x >>> import OPi.GPIO as GPIO >>> from luma.lcd.aux import backlight but after add this line, I got many error that told me that library is used for Raspberry pi only: >>> serial = spi(p…

Hello, i'm trying to make a mesh network with some Orange PI Zero devices, but ibss (adhoc) and 80211s (mesh) seem not working...with an usb wifi work fine... I have read that this device's support isn't the best, but i don't kwnow if my case is a release specific bug or these modes aren't really supported. Installed release "Armbian_5.38_Orangepizero_Debian_stretch_next_4.14.14", i have also trying dev kernel but this don't load the device... What are the really working modes and valid interface combinations? Reported info by iw list command seem not correct. Thanks for the help

Hello, I'm following my investigation to make possible an Open Hardware & Open source solution for schools (cf. https://forum.armbian.com/index.php?/topic/4929-which-card-choose-to-deploy-an-educational-open-source-os-in-schools/&tab=comments#comment-37422 ) I can't use the WiFi. I didn't found information on the forum for Orange Pi PC+ on board wifi (found some but it was for USB wifi). I have downloaded Ubuntu desktop – legacy kernel on https://www.armbian.com/orange-pi-pc-plus/ and installed it on class 10 SD card with Etcher ( Armbian_5.30_Orangepipcplus_Ubuntu_xenial_default_3.4.113_desktop.img). I'm using 3A 5V power …

Hi! I have a Hackberry and i've tried to install Debian jessie for Cubieboard. First I have installed a legacy version; hackberry boot up correctly but my keyboard don't work so i have replaced script.bin and overwrited u-boot-sunxi-with-spl.bin with the latest version (http://dl.linux-sunxi.org/nightly/u-boot-sunxi/u-boot-sunxi/u-boot-sunxi-latest/) and it's work. Then i've try to use Vanilla version. As the same, hackberry boot up correctly but my keyboard don't work. I've tried to recompile boot.cmd with correct dtb but nothing changed. Then i've tried to create uImage from zImage (linked to vmlinuz-4.2.3-sunxi) and overwrite u-boot.bin with the latest (…

Below is my attempt to compile the RealTek 8192cu driver for my ARMBIAN 5.31 stable Ubuntu 16.04.3 LTS 3.4.113-sun8i image running on my Orange Pi Zero. The BOLD area's below are the commands, I typed, everything else is exactly the way it came across on the console. Any help will be greatly appreciated. -0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0--0-0- root@orangepizero:~# apt-get install --reinstall linux-headers-$(uname -r) linux-headers-generic build-essential dkms git Reading package lists... Done Building dependency tree…

Hi: I want to add "nowayout" watch dog parameter to my orange pi pc. I think the syntax should be "sunxi_wdt.nowayout=1". but I don't know how to add this to kernel boot parameter in armbian? is there a config file to add boot parameter? BTW I found if I shut down my orange pi PC normally, I can not restart it unless I unplug/plug the power cord. is this behavior expected? thanks a lot for help!!

I'm using CT with Armbian 5.25(mainline) server version. The system hangs on every Sundays, and this is the 3rd time, since it hanged two weeks ago for the first time. When I connected a monitor with it, it says.. mmcblk0 : error -5 sending status command, retrying blk_update_request : I/O error, dev mmcblk0, sector 1503312 .... similar messages are repeated.. I have no idea what causes this. I do not use CRON. I installed these packages. Mpd, nginx, nfs server, samba server, deluge-daemon, pure-ftpd, Resilio Sync. Can anyone help me?

Greetings all. I've bought an Orange Pi PC recently, along with this screen, and I wanted to make the touch screen work on it. I have tried following this tutorial and this one, but so far I was only able to get the screen working. Currently installed image is: Armbian_5.35_Orangepipc_Debian_jessie_default_3.4.113. When I run `evtest` the only devices detected are `vmouse`, `sunxi-gpiokey` and `sunxi-ths`. I tried installing a GUI with xorg, lightdm and xfce. To show the GUI on the display I am using the following command: FRAMEBUFFER=/dev/fb8 startx But touch still isn't working. This is the output of armb…

Supporting of smb1 have been disabled on my windows hosts for security reasons. And now there are no ability to mount share from windows hosts on my orange pi pc. Can developers add this feature to armbian system in nearest updates? root@orangepipc:/media# mount -t cifs //192.168.1.5/D /media/share_test/ --verbose -o vers=2.1,user=user,pass=verystrongpassword mount.cifs kernel mount options: ip=192.168.1.5,unc=\\192.168.1.5\D,vers=2.1,user=user,pass=******** mount error(22): Invalid argument Refer to the mount.cifs(8) manual page (e.g. man mount.cifs) root@orangepipc:/media# mount -t cifs //192.168.1.5/D /media/share_test/ --verbose -o user=user,pass=verystron…

Since the CT (the A20 one, not the CT+) has been moved to CSC status, I've build a 22.04/jammy minimal image for my CT, and I figured I might as well share it with you. The only changes to "pure" armbian are some power management debug options in the kernel. https://github.com/IGNNE/cubietruck-armbian-unofficial/releases/tag/22.04-2022-09-09 SHA256 of zip file: 9d0028a9f5c6258a739f52f447bf4400d20fec52358f5006ae8a26b602acdfc0

I compiled full-armbian image for nanopi air. root@nanopiair:~# uname -a Linux nanopiair 4.19.25-sunxi #5.76 SMP Wed Feb 27 13:46:35 KST 2019 armv7l GNU/Linux and by armbian-config, on armbianEnv.txt overlays=spdif-out root@nanopiair:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: SPDIF [On-board SPDIF], device 0: spdif-dit-hifi dit-hifi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 root@nanopiair:~# speaker-test -tway -c2 -Dhw:0 speaker-test 1.1.3 Playback device is hw:0 Stream parameters are 48000Hz, S16_LE, 2 channels WAV file(s) Rate set to 48000Hz (requested 48000H…

Hi guys. I am testing a NanoPi Neo for an IoT project. I ordered one with unsoldered ethernet and USB ports. I am trying to use a miniature WiFi adapter plugged in the OTG port while powering the board from either the debug +/- pins, or from the 5V bus on the GPIO. The problem is that no mater what option I choose, the board powers up just fine, I can login using the debug port serial-over-consolem however the WiFi adapter doesn't pop up in the lsusb list. Using an OTG USB hub with external power, fires up the WiFi, however this is the only working way and my project has to have minimum cable clutter. I need to be able to plug in the NanoPi Neo on a PCB using its GPIO …

We are trying to install wifi driver for Xradio Xr-819 and also for D-Link Wifi Adapter in Mainline Image of Orange Pi PC. We have tried for xradio by https://www.cnx-software.com/2016/11/10/allwinner-h2-linux-android-sdk-and-allwinner-xr819-wifi-driver-released/ and https://github.com/fifteenhex/xradio. Also, we have tried by installing u-boot https://notsyncing.net/?p=blog&amp;b=2016.orangepi-pc-custom-kernel. We have tried for D-Link by https://github.com/xk/rtl8812AU_rtl8821AU and http://www.philipzucker.com/getting-goddamn-wifi-on-the-goddamn-orange-pi-pc/. Also, we tried to made modifications in file /etc/network/interfaces but that file shows in Read…

Flash 25.2.0 (The Latest Built Dec 01) to a SD card and boot a Orange Pi 3 LTS, Ethernet lost after sudo reboot the board. It did not even come back after physically power off and on. Have anyone experienced the same problem? The same board worked very well with Debian Bullseyes (downloaded from http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/service-and-support/Orange-pi-3-LTS.html). I googled and found Orange Pi 3B has similar problem. https://www.reddit.com/r/OrangePI/comments/1aojmn3/orange_pi_3b_ethernet_doesnt_work/

Hi, I finally have time to get back to my little project. I've been trying to get a working display with tinydrm for an ILI9341 base lcd. My setup works on OpenWrt with the older fbtft driver, but now I'd like to go back and try Armbian (current release is Jammy) on it. My first try with devicetree overlay seems functional but not correct. The display just show garbled data (see attached). What could be the problem with it? This is my env. verbosity=1 bootlogo=false console=both overlay_prefix=sun50i-h5 overlays=usbhost1 usbhost2 spi-spidev param_spidev_spi_bus=0 rootdev=UUID=e0ed80c4-a252-4d96-ad61-78b7834d6b8d rootfstype=ext4 user_ov…

Hi guys, Great work you are doing here, giving a second source for all kinds of fruits :-). My question: I like to have a "non desktop, no gui" = headless server with an armbian kernel >= 4.1 for the OrangePiOne to free up my expensive/more universal RPi2 for other tasks. I need a linux kernel >= 4.1, so it recognizes my DVB-C (T230) and DVB-S2 (S960/TT4600) that work with RPi2 as a headless TvHeadEnd SAT>IP server. TvHeadEnd itself works fine on your armbian kernel 3.4.110, but USB cards need a higher kernel level. I succeeded to compile myself with your tools and good explanation, got output, but the image does not startup, no video, no lights…

Hi! I just bought a NanoPi M1 board and It is running with Armbian without problem. Now I want to add a DHT22 temp & hum sensor but searching in the web I cant find any script to get it work. I saw that the RPi script doesn't work on the NanoPi M1 because the chip is differnt. In the Friendlyarm page there is a C script to work with the DHT11, but nothing with the DHT22. So, anyone have been experimenting whit it in this context? There are a Wiring Pi equivalent to NanoPi M1? Thanks

Hi guys, I have set my /etc/default /gpsd as following: It starts without any problem when I run "service gpsd start" but always fails to start at boot. The output of its status is as following after booting up: Does anyone know what I should change in order for gpsd to run properly at boot? Thanks!

Hi I am trying to set up auto-login with enable desktop, using armbian-config as user root, and getting 'killed' once I select which under-priviledged user to enable. (There's two to choose from, and both behave the same with the same error reult). I couldn't find a known issue, please help! OPi Zero LTS 512MB / Armbian from armbian.com Sam

Hello guys, I have an annoying issue with my OPiPC where I simply cannot get HDMI output. I am certain it is not a hardware issue! My OPiPC works fine with HDMI output & android. I have tried a known good HDMI->DVI-D adapter with various settings, and direct HDMI connection with various settings. It is a fresh install of Armbian 5.20 with apt-get update & apt-get upgrade. I have tried a plethora of h3disp settings and direct bin2fex configs! What could be wrong? Here is the current setup I am testing, which I would like to get working: -LG W1942TQ ( 1440x900 native ) -Working HDMI cord and HDMI->DVI-D adapter Interesting bits of the fex file…