Allwinner sunxi

Greetings all! I'm working to get my BananaPro (LeMaker board) up and running with Armbian 5 (Armbian_5.04_Bananapipro_Debian_jessie_4.4.3.raw) just downloaded to a fresh SD card. The radio is discovered and appears to be at least tolerated by the drivers. I've modified and recompiled as directed, the boot.cmd as such to point to the bananapro.dtb file directly: setenv bootargs "console=tty1 root=/dev/sda1 rootwait rootfstype=ext4 sunxi_ve_mem_reserve=0 sunxi_g2d_mem_reserve=0 sunxi_no_mali_mem_reserve sunxi_fb_mem_reserve=16 hdmi.audio=EDID:0 disp.screen0_output_mode=1920x1080p60 panic=10 consoleblank=0 enforcing=0 loglevel=1" #-----------------------------…

Hi All, Its been a week learning, battling and reading posts on armbian forum which was very much helpful - i now starting to master orange pi and armbian! However i can't seem to understand how to trigger the two on board LEDs (Red & Green), in one of the armbian images i tested this was implemented but not in the armbian version suggested for he Orange PI Zero Plus 2 H5: https://www.armbian.com/orange-pi-zero-2-h5/ It seems that my leds folder is empty, where to download or how to populate the missing files? ls /sys/class/leds Empty folder uname -r 4.14.4-sunxi64 modprobe gpio-sunxi modprobe: FATAL: Module gpio-sunxi not …

Hello, I just fresh installed Armbian_5.31_Lamobo-r1_Debian_jessie_next_4.9.7.img on my R1(which is for me a fantastic device). I tried to use GPIO by sysfs like I used to do on 3.4.113-kernel. on 3.4.113: echo "17" > /sys/class/gpio/export echo "out" > /sys/class/gpio/gpio17/direction cat /sys/class/gpio/gpio17/value echo "1" > /sys/class/gpio/gpio17/value gpio -g read 17 ...this is working fine ls -l /sys/class/gpio/ --w------- 1 root root 4096 Nov 4 19:17 export lrwxrwxrwx 1 root root 0 Nov 4 19:17 gpio14 -> ../../devices/platform/gpio-sunxi/gpio/gpio14 lrwxrwxrwx 1 root root 0 Nov 4 19:17 gpio1…

hi all . i found good URL https://gist.github.com/xsukax/77c627d7274736408314 aptitude install git yasm pkg-config , and then follow the URL , then i get ffmpeg . ---------------- regards .

Hi I have the following question which I have asked both to someone from Armworks and also #friendlyelec on free node. I haven't got the solution but it has lead me towards the answer. So my problem is in not being able to get xserver running that it indicates the driver "sun8i-de2" can not be found. As far as I can find not having the driver is the entire problem, however I can't find where I can get it. Below I have posted my full problem below: I have been having problems getting things to display on the LCD display using Xserver. I have been successful displaying images using fbi though. The board the we have it the NanoPi-Neo Plus2. Currently…

Hi everyone, I have an armbian 5.38 headless system on an orange pi zero2plus board. Attached to this board there's the expansion usb board with a wifi dongle and another board connected to twi interface of the gpio header. I power supply the board from the same header with a 5V 5A power supply, I verified and I have no holes on 5V and 3.3V voltage. The external usb dongle is configured as AP with nmcli, the internal wifi board is configured as w-station and is hooked to my home network. On this system is running a python-flask-uwsgi "daemon" that I'm developing. Well, randomly my system hangs, I can't connect to my flask web page, I can't connec…

Hello everyone I do not know how long, but I found out today that they no longer the wlan0 interface slla my lambo r1. I do not remember to have done in the configuration file changes lately. What can I check? These are the message by the boot if they can help: [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.7.3-sunxi (root@xenial) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.1) ) #26 SMP Wed Sep 14 19:50:18 CEST 2016 [ 0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data ca…

Hi, usb and emmc is not working for the A64-OLinuXino-2Ge8G-IND board while using the armbian build in dev. Armbian_20.05.0-trunk_Lime-a64_buster_dev_5.5.15 No change to the config of kernel, choosing lime-a64 and no desktop when asked to by compile.sh When compiling, the only choice for lime-a64 has the description: A64 quad core 1GB RAM SoC GBE eMMC Wi-Fi/BT. That doesn't correspond to the A64-OLinuXino-2Ge8G-IND. The image provided by olimex is working, ftp://staging.olimex.com/Allwinner_Images/a64-olinuxino/linux/1.latest_images/buster/images/ but when compiling their build i have the same issue and i…

Hi there, 2 days ago I did apt update + apt upgrade on my OPi3, everything fine. Yesterday I did a system reboot (as suggested "kernel changed"), then Eth port went dead. No even ARP works (ARPING). Have tried: - ifconfig shows correct values, - ethtool shows 1Gbps FDX connection, also same on router (OpenWRT TL-WR1043ND w 18.06 software), - changed eth cable, - on other OPi connected to same switch / router (also went dead) depowering device helped, but not on OPi3, - ARP shows MAC/IP not resolved, - WiFi (configured as AP) looks working. - also changed port on router and did power cycle device, nothing helps. - on r…

Theoretically Armbian supports wifi on BPI M2+ since v5.13. I'm on v5.25 desktop version, bluetooth works but no wifi. Do I need to install any drivers?

Hi. I would like to ask you how to add and read temperature and humidity from sensor DHT11 on Nano Pi Neo Core 2 with armbian. I want to use PA13 pin (CS form SPI1) I try to enable overlay: sudo modprobe dht11 cat /sys/bus/iio/devices/iio:device0/in_temp_sclae return : -119 When I try add dht11 to overlay in /boot/armbianEnv.txt this module after reboot is still disable. Any suggestions?

I don't know why fan doesn't work on my OPI +2E i even connected fan on gpio pin 4 and 6 . I'm noob but learning stuffs None of the gpio pins is working . Please tell me how to turn this 2 pin on for my fan. Please help me !!!

Hi! So the problem is when I configure wifi hotspot using hostapd, isc-dhcp-server, and ifupdown, I'm able to start the AP, connect to it, and ping. However, the moment any device connects to the AP the serial console gets spammed with this message around once a second: protocol 0000 is buggy, dev wlan0 This happens on the unofficial Armbian build (from the Armbian OrangePi Zero3 page), DietPi, and the official OrangePi Debian build. The wireless band doesn't matter. Kernel version: 6.1.31-sun50iw9. I tried to set up the AP with NetworkManager, but couldn't manage to connect to it. Probably DHCP issues that I couldn't resolve. I haven't …

Hello, I`ll try to hook up display to OpangePi PC, But have no output. My English is not native so i`ll try to write in simlpe way. image Armbian_23.8.1_Orangepipc_jammy_current_6.1.47_minimal.img.xz my dts: /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { target = <&spi0>; __overlay__ { status = "okay"; // cs-gpios = <&pio 0 9 0>,<&pio 0 8 0>; /* PA9=CS0 for LCD, PA8=CS1 for touch */ display: display@0 { compatible = "ilitek,ili9341"; reg = <0>; pinctrl-names = "default"…

Hi, Since recent I have an issue that my Orangepi doesn't start anymore. My microSD is fine (did a full diskcheck using badblocks on ubuntu), en I can access all the files without issues. However, it doesn't want to boot. Every time I try to boot it (Orangepi pc), it gives the first black screen until starting kernel, and then gets stuck on the blinking underscore. For information: I have an Orangepi PC and Armbian 5.32 with mainline kernel. Now, this happened after I did an apt-get upgrade (incl. kernel upgrade) from 5.30 to 5.32, and then didn't reboot, but my orangepi had a short power interruption. After this it didn't want to start…

Hello! Please help! How I can include Cyrillics (Russian) in consoles? I need keyboard layout pattern and the console on Cyrillics. apt-get install console-setup keyboard-configuration console-cyrillic dpkg-reconfigure locales dpkg-reconfigure console-setup dpkg-reconfigure console-cyrillic dpkg-reconfigure keyboard-configuration It doesn't help. Problem with console-cyrillic. Such package is absent.

Hello guys, I have an BananaPi M1 board runing armbian 5.31, already installed apache and mysql months ago, also an sata drive and the box is running smooth, I have alot of sensors around the house that are pushing new values to my mysql database, every minute, or every few minutes, but now I want to setup my cameras to use the FTP to store images in a folder accessible by apache, when cameras detect motion, can you point me in the right direction to install a FTP server I want to be able to see all the images saved by the cameras, in my dashboard, a website I made and host in this BananaPi box.

I trying all version on Orange Pi H5 Zero and nothing working. Only one green light start and after 3 second stop lighting. Before i use Armbian on this machine (meybe update firmware)

I am trying to set up Wifi AP on OrangePi Zero board. Basically, I install and configure hostapd and dnsmasq and create a script, which does the following (it is run as sudo): nmcli radio wifi off rfkill unblock wlan ifconfig wlan0 172.16.0.1 netmask 255.255.255.0 broadcast 172.16.1.255 service dnsmasq restart /usr/sbin/hostapd /etc/hostapd/hostapd.conf This is the /etc/dnsmasq.conf: port=53 domain-needed bogus-priv resolv-file=/etc/dnsmasq/resolv.conf interface=wlan0 listen-address=172.16.0.1 bind-interfaces addn-hosts=/etc/dnsmasq/hosts.conf dhcp-range=172.16.0.50,172.16.0.150,12h dhcp-leasefile=/var/lib/misc/dnsmasq.…

Hi guys, I am trying to install `ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.14-sunxi64` to the internal MMC with `nand-sata-install` but it seems that the internal MMC is not available after booting from SD. I tried to set the `sdc_detmode` as described here: https://forum.armbian.com/topic/1702-orange-pi-plus-2e-where-is-16ghz-and-sd/?tab=comments#comment-13163 But there is no `script.bin`. Any idea on how to flash the internal MMC on a Neo Core 2? Cheers! Robert

hello, my orangepi3 after the updates of firmware of these days seems to loose eth0, at reboot take eth0 and eth0:avahi with class 169 ip. i made backups (i use a sd to restore the mmc mouting hd and then copy the gzip image) so i have not problems to restore but, i suspect, the previus version is working but the new one not. sorry for my worst english... ab

Hi, First, i'am french, excuse my bad english... I have a problem with my orangepi zero using a bme280 weather sensor with i2c. (I have 2 sensors) After long search and try, i've found the way to make this sensor working with the orange pi zero, by reading the datasheet where it's indicated that you must put CSB to Vdd to select i2c interface. !!! - I never wired this pin to my rapsberry pi and it always work , never see in any tuto too!!! Th problem is that I don't read good values, it seem that the values are always the same, based on calibration . I try to figure out what happen but i'm not so friendly with i2c pro…

The lighttpd fails when installed on following two distros: (1) Armbian_5.25_Orangepipc_Debian_jessie_default_3.4.113 (2) Armbian_5.25_Orangepipc_Ubuntu_xenial_default_3.4.113_desktop How to solve this problem? The code below gives the details. Welcome to ARMBIAN 5.25 stable Debian GNU/Linux 8 (jessie) 3.4.113-sun8i pi@orangepipc:~$ uname -a Linux orangepipc 3.4.113-sun8i #10 SMP PREEMPT Thu Feb 23 19:55:00 CET 2017 armv7l GNU/Linux pi@orangepipc:~$ sudo apt-get update pi@orangepipc:~$ sudo apt-get install lighttpd pi@orangepipc:~$ sudo systemctl restart lighttpd pi@orangepipc:~$ sudo systemctl status lighttpd -l ● lighttpd.service …

Hi, just a quick question: Why is OTG disabled? I read some "performance issues" or "high CPU usage by OTG" etc... But can someone be more specific?

Hello, I am having strange problem with Olimexino A20 Micro, Ambian 5.38, 4.14.14. After every 2-3 days standby with minor cpu usage I am getting an FS error. I have tried Armbian Ubuntu/Debian and different sd cards but this doesn't change anything. I think with previous kernel there wasn't such an issue. I've connected it to the serial port and I see: login: [381301.434449] EXT4-fs error (device mmcblk0p1): ext4_journal_check_setected aborted journal [381301.444715] EXT4-fs (mmcblk0p1): Remounting filesystem read-only [381340.727458] EXT4-fs error (device mmcblk0p1): ext4_find_entry:143621620: comm sh: reading directory lblock 0 [381494.351427] EXT4-fs e…

I have found other treads that address "tv out not working" but none have been applicable. They point to files that are not on my system. It is an older orange pi zero. I have installed the latest armbian image. Here is the "lsb_release -a" return: Distributor ID: Ubuntu Description: Ubuntu 20.04.2 LTS Release: 20.04 Codename: focal I am currently operating headless and the login splash screen says "Welcome to Arbian 21.02.3 Focal with Linux 5.10.21-sunxi" I am trying to use the 13 pin connector. Pin 2 = ground (shield) and Pin 9 = video signal (center conductor) I have found forum threads about enabling the tv out bu…

Hi, After today upgrade (Kernel / Firmware) my DVB-T pen stop working with dump1090. Error message: /usr/bin/dump1090 --net --gain -10 --modeac --net-bo-port 30005 --net-bi-port 30104 Found 1 device(s): 0: Realtek, RTL2838UHIDIR, SN: 00000001 (currently selected) Kernel driver is active, or device is claimed by second instance of librtlsdr. In the first case, please either detach or blacklist the kernel module (dvb_usb_rtl28xxu), or enable automatic detaching at compile time. usb_claim_interface error -6 Error opening the RTLSDR device: Device or resource busy I tried to follow this tip: http://discussions.flightaware.com/ads-b-flight-tracking-f21/dump10…

Hi. I would like to install Armbian on Cubieboard2 with eMMC as internal storage and have faced some problems. The first challenge was to make eMMC accessible, it was solved using .fex from cubieboard sdk for this revision (also tried cubieboard2dual.fex, but without any effect). The second problem was behavior of nand-sata-install included in desktop image - it overwrite wrong root partition (external SD instead of eMMC), but it was also solved using latest version of nand-sata-install. But after installation, system isn't booting from eMMC. Since root filesystem is successfully copied to eMMC, I think there is problem with bootloader. Is there an…

Hi, Before I start, I want to thank the developers for making great products. I am fairly new to SBCs, but unlike the official images, Armbian works great on my OP plus 2E. I have recently bough a OP zero+ H5, but as it lacks ethernet, I can't set it up. Is there a way (like raspbian) to set up wifi on the sd card after i burn the image on to it?

Hello, I use Orange Pi Zero + 4 ports USB hub + CM108 USB-Audio cards with mic-in. All by default. Each mic is captured with sipmle commands like: arecord -v -r 44100 -c 1 -D "hw:CARD=Device_1,DEV=0" -f S16_LE > mic1.wav When 3 cards capturing simultaneous all working well. But if I start capturing with 4th card simultaneous I get two cards with crackling recorded audio. I even can see that arecord saves less data from these two cards (file size is less than with 3 cards). No error/warning provided anywhere (dmesg, syslog, arecord). Moreover, if I stops recording from one card - it becomes normal fo…

I just got 4 NanoPi Duos v1.1 and the OTG port functions (unlike v1.0)! This is with the FriendlyElec image. I was wondering should I compare the FriendlyElec's sun8i-h2-plus-nanopi-duo.dtb to the one on Armbian? I already tried messing with Armbian's sun8i-h2-plus-nanopi-duo.dtb by changing usb@01c19000 status = "okay" and adding dr_mode = "host". I'm not sure I can just drop in the dtb? Any way, I'll see what I can figure out. I'm excited the OTG port works now for more than just power since that saves you from buying the Mini Shield if you have a simple project that just needs a USB drive or camera.

I run the OPi Zero as a Pihole with etherned, and I would like to minimize power consumption as low as possible. 1. I did change the frequency to be between 120 - 960 Mhz, and ondemand. This probably reduces power and heat too. 2. I'm not sure how to disable USB (I don't need it at all) and WiFi. I read the threads, like this but not sure how to do. Can you please guide me? 3. I saw there are other options too, with a tool h3consuption, but I don't know how to install it and what can I do to squeze down a couple of mW's more. Your help is very much appreciated!

Hello, Is it possible to get a WiFi-Direct connection from OrangePi Lite to for example smartphone and send a file to it? I mean with not using router. Thanks in advance for every answer!

Hello Everybody I'm using olimex olinuxino lime2. I'm to expiriment on real time linux. I could build the kernel with the real time patch by disabling newer kernel patches, .108 and on, but I would really like to have a ticking system. There are not options for this in the kernel menu configuration. Just tickless system. That may cause some extra delays on realtime processes. Is there a way to configure tick frequency at 1khz? Thank you for your time

hello everyone ! I'm trying to listen music with my orange pi over armbian of course. I have installed VLC and it seems works but not sound . I use the 3,5mm output connected to the amplifier At the moment no sound and no music .... Does anyone know what I have to do ? Thanks in advanced Walter

Anybody know how install ARDUINO IDE on ARMBIAN orange pi pc 2? Can I drop tar archive to home/pi/arduino

I'm using Armbian 5.38 stable Debian stretch 4.14.14-sunxi on A20 Lime2. I try to use PGxx pins (connector GPIO-1 on board), without any luck. I know i must use formula (position of letter in alphabet - 1) * 32 + pin number, so i have tried (for PG11): echo 203 > /sys/class/gpio/export echo out > /sys/class/gpio/gpio203/direction echo 1 > /sys/class/gpio/203/value but nothing happened. I tried from 192 to 203 (PG00 to PG11), but nothing happened. On the same connector (GPIO-1), PC23, PC18 and PB23 work perfectly. What am i doing wrong?

Hi, as I had set up my CubieTruck I decided to go with Legacy Wheezy ... Now I think about become a bit more current :-) Option 1 is to Upgrade to Legacy Jessie ... This is described in the documentation and hopefully should work that way, Correkt? Or Option 2 would be to go to Vanilla Jessie. Is this possible too? How? Thank you for your support, Ingo

Hi I try use Nokia 5110 with Orange pi zero. I found this library: https://github.com/rm-hull/luma.lcd and try to run it on my orange pi with this tutorial: http://codelectron.com/interface-nokia-5110-lcd-and-raspberry-pi-python/ so in python shell I add these: >>> from luma.core.interface.serial import spi >>> from luma.core.render import canvas >>> from luma.lcd.device import pcd8544, st7735, uc1701x >>> import OPi.GPIO as GPIO >>> from luma.lcd.aux import backlight but after add this line, I got many error that told me that library is used for Raspberry pi only: >>> serial = spi(p…

Hello. I am trying to control a servo, and after a lot of mistakes and hits in the face... finally i can move it with WiringOP (https://github.com/zhaolei/WiringOP) I use one of the examples called servo.c and the servo moves to one side and another. This is the first step, but the servo makes weirds movements. Watch this video. Any iddeas why? Any other way to control a servo? I am not C expert, some way to do it with Python? Thank you very much in advance. servo.c

Hi there, while trying to solve the issue with OPi PC and rtl8188 (thread link) I managed to get console on the UART interface, nice feature considering my networking issues, btw is there a way to output the kernel messages (dmesg like) to the UART console in real time? I'm asking cos the issue that I'm trying to fix involves system freeze + automatic reboot and I would like to see the logs during the event. I already tried to mess with printk, but it's very likely I've done something wrong.

I use armbian installed on emmc of Nanopi neo air. I want use the sdcard, buit i can't see the card. I insert the card after i boot from emmc. How can i mount the card?

I am on Debian 7.9, kernel 4.1.6-sunxi. Since a couple of days I get an error message when I want to open a LUKS container (e.g. cryptsetup luksOpen ...). /dev/mapper/control: open failed: Kein passendes Gerät gefunden --> no device found Failure to communicate with kernel device-mapper driver. Check that device-mapper is available in the kernel. Kann die Gerätezuordnung nicht initialisieren. Ist das Kernelmodul dm_mod geladen? --> is dm_mod really loaded? I tried to manually load dm_mod and get another error message: > modprobe dm_modlibkmod: ERROR ../libkmod/libkmod.c:554 kmod_search_moddep: could not open moddep file '/lib/modules/4.1.6-sunxi/modules.dep…

Hi, When I put a heavy load on my NanoPi NEO2, it locks up. The ethernet light keeps flashing, so there is still something alive? After a power reset, the NEO2 works again. I've already put a CPU fan on my CPU. CPU temp is at 25 degrees Celsius in rest, and goes up to 37 degrees Celsius under the heavy load. The heavy load is a "make -j4" of a C source code project Tips how to solve this? sander@nanopineo2:~$ while true; do date ; uptime ; cat /etc/armbianmonitor/datasources/soctemp; sleep 2; done | tee mijn-log.txt Tue Aug 22 11:46:37 UTC 2017 11:46:37 up 5:24, 2 users, load average: 0.00, 0.00, 0.00 28342 …

Hello :), I have updated my system from "Armbian_5.35_Debian_jessie_3.4.113" to latest "Armbian_5.53.180722_Orangepizero_Ubuntu_bionic_next_4.17.9". With jessie there will only S0, S1, S2 displayed and Im Working with S1 (Uart1) and S2 (Uart2) from the 13 Pinheader. With Bionic and also Stretch i got S0, S1, S2, S3, S4, S5, S6, S7 and none of them is working. So how can I access the Uart1 and Uart2 with the new Bionic build?

Downloaded latest Jessie image for Cubietruck. Loaded to the sd card using instruction on site. When i power CT on, looks like it start booting, all leds are flashing as on normal boot, but screen is black. Please advise what to check, how to debug. Card seems ok, because i can boot other images.

I have Orange Pi Plus 2 running Ubuntu Bionic with Armbian Linux 4.19.62-sunxi and I would like to upgrade it to recent Armbian build based on Ubuntu Linux Server and move OS to SSD connected to one of USB ports. I tried to use Armbian_22.08.2_Orangepiplus_jammy_current_5.15.69.img.xz but it does not connect to both HDMI and network. I tried unofficial command line interface images from product page and weekly released unsupported community builds. Behavior of all these builds is the same - no output to HDMI, no network connection. Finaly I found that recent image for Orange Pi Plus / Plus 2 which boots is Armbian_22.08.1_Orangepiplus_jammy_current_5.15.63.img.xz.…

Hello, I recently bought an Orange PI Lite and wanted to connect it to my WiFi (WPA2 - Personnal) to run a CUPS server. So I connected it to my computer via the serial pins and tried to connect it to my network using nmtui. That looked like it worked well if only a bit laggy at first. But after rebooting it i noticed it was totally unreachable from any other device on the network. So I started pinging everything and started noticing weird stuff : After a reboot Nothing can ping the orange pi unless he pinged them first. When pinging another device from the pi, the first few packets are lost and all following are ~1ms. …

Hi team, I am trying to get a voltage drop (3.3V to about 0V) detected on a GPIO pin on my OrangePi Zero running Armbian buster 20.02.1 with Linux 5.4.31-sunxi. I have another OrangePi Zero on which I have already managed to install I2C OLED screen, and the i2cdetect was working, and so on... For this one, I got a problem with the gpio group not existing. As I tried to install OPi.GPIO, I got usermod: group 'gpio' does not exist It's an Armbian version that I downloaded yesterday, and upgraded today with armbian-config. So... What did I do the wrong way? Thanks.

For some days now I have the board mentioned in the subject, the goal is to have a webserver, git server, and maybe lateron something like a mini-personal-cloud for my family. Yesterday me and my brother finally decided which OS to use - and dd-ed the SD card with the Armbian/Debian Vanilla Jessie Server image (Armbian_5.10_Lime2_Debian_jessie_4.5.2). Some hours later after installing apache2 and trying things out I thought it would be a good idea to do an apt-get upgrade for security reasons before exposing the server to "the world". Unfortunately it was not: The device is not booting any longer after the upgrade. This is the log output of /var/log/apt/term.log (I moun…

Good evening, I'm using a NanoPi Neo Air for streaming audio via bluetooth to a I2S sink. It's working in general but the audio data breaks away every second. It's always a on/off. I'm pretty sure it's connected to the speed between H3 - AP6212a but I'm not able to get it to work propably. I set the UART ttyS3 speed to 1500000 bit/s: My Fexedit looks like that: [bt_para] │ │bt_used = 1 │ │bt_uart_id = 3 │ │bt_uart_baud = 1500000 │ …

considering to buy orange pi 3 with new H6 cpu, usb3.0 port and onboard emmc, but everyone has been complaining official images, just wondering if orange pi 3 will be supported soon.

I noticed the Neo+ 2 has a blue LED: line 10: unnamed "nanopi:green:pwr" output active-high [used] line 20: unnamed "nanopi:blue:status" output active-high [used] It's not doing the heartbeat flash like the NanoPi Duo. uname -a Linux nanopineoplus2 4.14.15-sunxi64 #95 SMP Wed Jan 24 10:55:45 CET 2018 aarch64 GNU/Linux

Hi guys a having problems to boot the latest armbian buster 5.3.Y kernel on the orange pi win plus. I tested other older kernels(4.19 and 3.xx) and worked fine except for Bluetooth and WiFi hotspot. I am trying to upgrade to buster 5.3 but always as result kernel panic(same on bionic and stretch 5.3). power supply is ok and tested on 3 microsd card. this is the debug information from an ttyS0 consoles it is continues rebooting. need some help debug.txt

Hello, I have a 4x20 LCD display (with an HD44780 compatible adaptor) connected to my Banana Pi. It is running (freshly installed, switched from Bananian) on the mainline kernel: Linux bpi 4.9.7-sunxi #1 SMP Thu Feb 2 01:52:06 CET 2017 armv7l GNU/Linux However, the display is not recognized. I checked the wire connections multiple times, they're okay and the backlight is on. So I assume this is a software issue. The output of "i2cdetect -y 1" is: 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- --…

Hello, Unfortunately as I read from forums mainline kernel has no driver for gc2035 and v4l2 driver. I have tried Armbian_5_65 and Armbian_5_59 debian stretch but they are not contains these drivers and eventually modprobe command fails. As I understand, I have 2 different solutions to run camera on my system; 1- Going back to legacy build. But I do not know how to go back the legacy build which is last supporter these drivers. 2- Installing required drivers. (Also I want to prefer this solution because going back to legacy build may cause some bugs) How can I install required drivers to mainline stable build and where can I find …

OK, folks, I have I2C working for Luma.OLED, but now I'm trying an SPI display (SSD1331) and having some issues. I modified OPi.GPIO pin mappings as follows (see below), but I'm wondering if my SPI configuration is correct. I'm using overlays=spi-spidev and param_spidev_spi_bus=1, but I'm wondering if I should also be using CS1 configuration as well since I'm using SPI bus 1 (bus 0 is reserved for flash). i.e. param_spidev_spi_cs=1 and overlays=spi-add-cs1. I only ask this because the Luma.OLED instructions say "Because CS is connected to CE0, the display is available on SPI port 0. You can connect it to CE1 to have it available on port 1. If so, pass port=1 in your seria…

Hello everyone! *sorry for my bad English. I found the page https://www.armbian.com/longanpi-3h/ Sipeed LonganPi 3H but no OS images to download. Can anyone help me and give me links to ISOs or there are none yet?

Hi. I tried to search the forum but it seems I put wrong search words... How should I install the display so I can run Geany (IDE)? Here is my data http://sprunge.us/WWGg

Hi, since one the last two kernel updates I experience random out of memory scenarious on my Cubietruck. Up until then all was fine. When Oom Killer kicks in the following is logged: ........................................ Spoiler Mar 4 06:54:23 cubietruck kernel: [80988.962548] sh invoked oom-killer: gfp_mask=0x24000c0(GFP_KERNEL), nodemask=0, order=2, oom_score_adj=0 Mar 4 06:54:23 cubietruck kernel: [80988.962563] sh cpuset=/ mems_allowed=0 Mar 4 06:54:23 cubietruck kernel: [80988.962584] CPU: 1 PID: 10543 Comm: sh Not tainted 4.9.12-sunxi #4 Mar 4 06:54:23 cubietruck kernel: [80988.962588] Hardware name: Allwinner sun7i (A20) Fam…

hallo, i downloaded debian jessy image with kernel 4.0.5 from there: http://mirror.igorpecovnik.com/Lamobo-r1_Debian_3.1_jessie_4.0.5.zipand installed it on bananapi. at first boot seems to be system self-autoconfigured and reboots. Now i see that /etc/network/interfaces is linked with interfaces.r1 and in /boot i found those files: config-4.0.5-lamobo-r1, System.map-4.0.5-lamobo-r1, vmlinuz-4.0.5-lamobo-r1. can it be that autoconfiguration has my bpi as router configured. How can i fix that manualy? nex question: on the boot i see one pinguine, but while bpi has 2 cores it shoul be 2 pinguins or not ? best regards Marijus

Hello I having some issues with the Armbian Buster image for Nano Pi Neo 2. https://www.armbian.com/nanopi-neo-2/ When I launch the command sudo apt update, I'm getting the following error: The package cache file is corrupted, it has the wrong hash I already downloaded the image several times, I still getting the same error. My SD card is ok, I have tried with 2 different ones. I can remember having the same issue with a preview version. What's wrong??? Thank you

Hello! I try to turn on usb gadget mode on my OPi. For example g_ethernet, or g_midi. Read many posts, but still don't understand what I should do. Is it possible to turn on gadget mode without compiling my own armbian? Also, I had found on this forum info that legacy roms already have OTG support from the box. Is it true? May be somebody knows tutorials of how to turn on usb gadget mode?

% cat /etc/armbian-release # PLEASE DO NOT EDIT THIS FILE BOARD=zeropi BOARD_NAME="ZeroPi" BOARDFAMILY=sun8i BUILD_REPOSITORY_URL=https://github.com/armbian/rkbin BUILD_REPOSITORY_COMMIT=3e533c9 DISTRIBUTION_CODENAME=buster DISTRIBUTION_STATUS=supported VERSION=20.02.1 LINUXFAMILY=sunxi BRANCH=current ARCH=arm IMAGE_TYPE=stable BOARD_TYPE=conf INITRD_ARCH=arm KERNEL_IMAGE_TYPE=Image # dpkg -l | awk '{print $2" "$3}' | grep -Ei "^linux|zeropi" | sort linux-base 4.6 linux-buster-root-current-zeropi 20.02.1 linux-dtb-current-sunxi 20.05.0-trunk linux-image-current-sunxi 20.05.0-trunk linux-libc-dev:armhf 4.19.98-1+deb10u…

I use mpv in Armbian 5.10 on a OPiPC, HDMI attach to my audio and TV . I checked the audio devices at first: mpv --audio-device=help List of detected audio devices: 'auto' (Autoselect device) 'pulse/alsa_output.platform-audiocodec.analog-stereo' (audiocodec Analog Stereo) 'pulse/alsa_output.platform-sndhdmi.analog-stereo' (sndhdmi Analog Stereo) 'alsa/default' (Playback/recording through the PulseAudio sound server) 'alsa/plughw:CARD=audiocodec,DEV=0' (audiocodec, /Hardware device with all software conversions) 'alsa/plughw:CARD=sndhdmiraw,DEV=0' (sndhdmi, /Hardware device with all software conversions) 'oss' (Default (oss)) 'jack' (Default (jack)) …

Hey guys. I need your help. Since I'm new to linux I don't know what happened and what to do. Latest armbian was installed on my eMMC. Today at morning I woke up and logged in by ssh to my orange pi pc plus and get 'input/output error' for every single command. I've tried to reboot it by powering off and on and after that I could not log in by ssh. (and I noticed that green led not blinking and ethernet port green and orange LEDs was constantly on) I've inserted 16gb SD card with latest armbian installed on it and it works by booting from it(green led is blinking, ethernet port LEDs are also blinking, everything is ok). I've tried to list partitions a…

Running on Virtualbox-compiled Armbian_5.32_Orangepiplus_Ubuntu_xenial_dev_4.11.5.img. I installed docker and am trying to run a pihole container. Because it's a new image, it tries to download it. But it never gets to the end, because it always freezes. OrangePi+ stops answering pings and I have to hard reboot. Here's almost what it looks like before locking up. I've also had it lock up during file transfers, differs from one time to the other. Spoiler Unable to find image 'diginc/pi-hole:arm' locally arm: Pulling from diginc/pi-hole 75419788cca0: Retrying in 5 seconds a270c0806eb4: Download…

Hello, I have just built an image with the default parameters of the Lime A20 board. It seems that the system does not detect any sound card. aplay -l aplay: device_list:268: no soundcards found... uname -a Linux lime 4.13.6-sunxi lsmod Module Size Used by cfg80211 376832 0 rfkill 20480 1 cfg80211 sun4i_gpadc_iio 16384 0 evdev 20480 1 at24 16384 0 sun4i_ts 16384 0 sun4i_gpadc 16384 0 nvmem_sunxi_sid 16384 0 sun4i_ss 24576 0 uio_pdrv_genirq 16384 0 uio 16384 1 uio_pdrv_genirq As you can see above, there is no module related to sound. …

Hey everyone, I am attempting to update my Orange Pi Zero from Armbian 22.0.2.1 to the latest 23.11 version however I am running into the issue that I am stuck on how to perform this update, I have tried it using the sudo apt dist-upgrade command and tried regular sudo apt update and upgrade commands but everytime it says there are no new updates available (also no errors), when there is clearly a new version 23.11 available here: https://www.armbian.com/orange-pi-zero/ What am I doing wrong? Is it maybe because it says unsupported userspace?

I'm powering my NanoPi Neo V1.4 1801 through the USB type A port beside the Ethernet RJ45. I'm using Armbian 23.11.1 bookworm with kernel Linux nanopineo 6.1.63-current-sunxi. Now I want to enable the Micro-USB port (usually used for powering) to act as an USB host so that I can plugin an USB-stick. I found very few instructions for e.g. Orange Pi. There the device tree needs to be changed for usb@1c19000 and usb0-vbus. Also in armbianEnv.txt the line param_usb0_mode=0 should be added. But none of the instructions work for my NanoPi Neo. In the schematics, a SY6280 is connected via GPIOL2/USB0-DRVVBUS to the H3 cpu. …

Hi all, I build Armbian for my NanoPi Air with both Linux 3.4 and Linux 4.X, and config usb to be an USB Ethernet Gadget but it does not work with Linux 4.X. There is nothing showing when "dmesg | grep gadget" on Linux 4.x But in Linux 3.4 I got following messages: root@nanopiair:/# dmesg | grep gadget [ 2.559263] g_ether gadget: using random self ethernet address [ 2.565929] g_ether gadget: using random host ethernet address [ 2.582905] gadget_is_softwinner_otg is not -int [ 2.582923] gadget_is_softwinner_otg is not -int [ 2.583012] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 [ 2.590546] g_ether gadget: g_ether ready [ 13.…

Hello. I have a small problem: I can't change the language on my OPi Zero. I have successfully done that with OPi Lite 2 and OPi 3, but for some reason on the Zero when I go to change it, the module fails to load and just quits back to the same "menu page". (essentially does nothing). The only thing I can think of, is that both of the other boards have 1Gb RAM and this only has 512Mb and thus it runs out of memory? That doesn't sound too plausible though - a list of keyboard languages shouldn't take tens or hundreds of megs of RAM. As far as I know, each board is running the same version of Armbian, so that shouldn't be a problem.

Greetings all. I've bought an Orange Pi PC recently, along with this screen, and I wanted to make the touch screen work on it. I have tried following this tutorial and this one, but so far I was only able to get the screen working. Currently installed image is: Armbian_5.35_Orangepipc_Debian_jessie_default_3.4.113. When I run `evtest` the only devices detected are `vmouse`, `sunxi-gpiokey` and `sunxi-ths`. I tried installing a GUI with xorg, lightdm and xfce. To show the GUI on the display I am using the following command: FRAMEBUFFER=/dev/fb8 startx But touch still isn't working. This is the output of armb…

Hi, I use an OrangePi Zero as a race timer for a car. It is powered from the car. So when the car starts the OrangePi gets power and boots and when the car is turned off the OrangePi loses power and "turns off". This isn't ideal but I don't have a lot of options. I feel like this is a fairly common use case for electronics in cars especially ones like race timers etc. Unless I have a battery as well. I was wondering what are the best things to do to protect against the sudden power loss so that I don't corrupt anything? Is it possible to make parts of the file system read only maybe? All I do with the OrangePi is run a C++ application, it use…

It was set to mount cifs in fstab, but seem not automatically mount. Since this is not supported?

I'm trying the new version of armbian for orange pi plus 2 . Is there some news to create an access point ? I saw there are some files and other files not Does someone could link to me some tutorial for the access point? I have several usb dongle wifi and wifi on chip After a lot of web sites I visited I'm not able to create an access point thanks

Hi all, I'm trying to access the GPIO from python context and I absolutely need to do it in a rootless way. (WSGI apache module) I'm a newbie and noticed that this is the library command causing the error inside the python library: Code: Select all fd = open("/dev/mem", O_RDWR); I do have /dev/mem on my armbian distro and clearly the access to /dev/mem is root limited, what's worst I don't have /dev/gpiomem Is there a way to create /dev/gpiomem so I can add the apache user to gpio group and solve this? Do I need to configure and compile a kernel by myself? please help me, thank you

Hi, I was wondering if anyone was having issues with the ethernet port using the legacy kernel ? It does seem to kind of work ... it will get DHCP from the router and configure the routing tables etc but after that it goes wonky. When I do a ping test from the router I get "50/50 transmitted, 15/50 received, 70% loss". A ping test from the opi-win to the router gets a similar result. If I try a ping/ssh from a PC connected to the router I get a 95% packet loss Everything else seems to work fine ... HDMI, USB, WiFi (AP/STA modes) which is really, really nice. Thanks TB

Hi, I have problems with the versions "Armbian 5.25 Orangepizero Debian jessie default" and 5.26. When i install Nginx, the directory "nginx" is created in /var/log/. After a "reboot" the directory is then "disappeared", not possible to start Nginx. I can create the folder with error.log and access.log and restart Nginx. After this, it runs. After a reboot again, nginx is missig again... Any hints? The same happens with 5.25 and 5.26 on OrangePiOne, so far tested... I thing i'm not the only one with this problem. (I testet with "root" permissions only)

I have OrangePi PC and I'd like to use HC-12 serial communications device. I've successfully used it with RaspberryPi Zero with these instructions: http://dev.drun.net/2017/05/10/reading-hc-12-from-rpi-and-sending-to-domoticz/ I've found this useful info: https://forum.armbian.com/topic/1524-orange-pi-one-how-to-enable-uart/ I've connected the HC-12 to OPPC as follows: VIN – Connect to 3.3 (PIN 2) GND – Connect to GND (PIN 6) RX – Connect to (PIN 8, UART0_TXD) TX – Connect to (PIN 10, UART0_RXD) I've got Putty connected to OrangePi. command "ls /dev/tty*" shows that I have /dev/ttyS0. I've tried to use it with Minicom: sudo…

first i was able to boot my nanopi from SD card and i was able to access it through SSH. then i was trying to boot my nanopi from EMMC but it was not booting. I already installed a different OS which is specialized for Eflasher (nanopi-neo-core_eflasher_friendlycore-xenial_4.14_armhf_20190522 ) . then i followed the steps carefully: http://wiki.friendlyarm.com/wiki/index. ... i_NEO_Core note : i was using commands since there is no HDMI. I typed : eflasher then i choose 1 and typed yes and waited until the OS was installed successfully and finally i powered off the nanopi, removed the SD card as mentioned, tried to power it on but i coul…

Hello, I have problems with the u-boot both with the prebuild "Armbian_21.05.1_Nanopineo_buster_current_5.10.34" image from the armbian.com and with the "Armbian_21.08.0-trunk_Nanopineo_buster_current_5.10.59_minimal" image built form sources . First of all, the u-boot versions are different. The prebuilt image has "U-Boot 2021.04-armbian" and the second one - "2020.10" The board boots ok with the both images, but the u-boot does not see the SD card properly and is not able to load the environment file from it: "Loading Environment from FAT... Card did not respond to voltage select! : -110" Is there any fix for this problem? Thanks, …

Latest doesn't seem to work at all, so something like 5.59 4.18.0-rc7-sunxi64 mentioned here https://github.com/armbian/testings would be ideal. Alternatively is there a way I can build old version myself? I ran ./compile docker BOARD=orangepilite2 BRANCH=dev but resulting image doesn't work also.

have there been more changes for Desktop recently except the repos? Yesterday I have updated and tried to compile, noticed that the function "fetch_from_github" was gone (replaced by "fetch_from_repo"?). After I changed my script accordingly I was able to compile, but the desktop doesn't come up any more. It looks like "fbturbo" module is completely missing? I don't see any reference to this in the logs; where should it be so I can try to debug?

Hi all I have a project where I'll be deploying the same configuration (including IP addresses) to a multiple Orange Pi Zeros. There will be some slight differences (hostname, information in one script) but largely identical. I was thinking about using a Linux VM to run a script that changes a base image (from a pre-set up machine) makes the changes and burns an image onto microsd. Is this a viable approach? Will I need to change anything else (MAC address related stuff?) Cheers!

Hello, It's my first message, I'm very proud to be part of your community, Armbian is epic ! I'm trying to add a chinese screen copy to my orangepizero (H2+ cpu). This is my screen: https://www.aliexpress.com/item/32587995145.html (copie of https://www.waveshare.com/3.5inch-rpi-lcd-a.htm) 1) Yesterday i setup my screen on Armbian_5.91_Orangepizero_Debian_buster_next_4.19.59 with success with: nano /boot/armbianEnv.txt : overlays=spi-spidev spi-add-cs1 param_spidev_spi_bus=1 param_spidev_spi_cs=1 nano /etc/modules-load.d/fbtft.conf : fbtft fbtft_device nano /etc/modprobe.d/fbtft.conf : options fbtft_device rota…

Hi all, I'm new here at the Armbian board. I operate a self made house automation based on a Raspberry using a self written PHP server and Homegear. To have a better wireless connection to a differential temperature sensor, I built a Homegear Gateway based on a Nano Pi Neo with Armbian OS and a 868 MHz CC1101 module. For the network connection I use a Realtek USB WLAN NIC (Realtek RTL8188EUS-Chipset). Most of the time the gateway works. But around 2-3 times per week the gateway hangs and I cannot log on anymore. A hard restart by unplugging power is required. The only indications I find are 2 dumps of the RTL8188EU driver in kern.log…

Hi, I am using orange pi one with the ubuntu desktop version. When i am trying to change the region using 'iw reg set US' and after retrieving the value using 'iw reg get' still the region are not changed. I was following the doc. https://null-byte.wonderhowto.com/how-to/ultimate-guide-upping-tx-power-kali-linux-2-0-0168325/ and was able to do it all steps but impossible to change region. Can anyone help me in this issue? Thanks in advance

Hello community! I use in my project "Orange Pi Zero Plus (Alwinner H5 - 512mb)". When using the image downloaded from the official site (https://www.armbian.com/orange-pi-zero-plus/ - Armbian Stretch mainline kernel 4.14.y), I get a set of errors when I boot and when I use the working OS, which I'm straining. The same mistakes I get if I build the kernel and the OS myself through "build" (linux-sunxi64-next). My equipment: Memory: SanDisk Ultra microSDHC Class 10 UHS-I 48MB/s 16GB Power supply: Raspberry Pi 3b+ Power Adapter (STONTRONICS) - 5.1V @ 2.5A Boot: full log - https://pastebin.com/M9g6ipUp Loading Environmen…

compiled https://github.com/armbian/build debian. uname -a Linux orangepipc 4.14.73-sunxi # 1 SMP Mon Oct 1 11:55:35 +04 2018 armv7l GNU / Linux apt update apt-get install -y build-essential linux-headers -uname -r` Reading package lists ... Done Building dependency tree Reading state information ... Done E: Unable to locate package linux-headers-4.14.73-sunxi E: Could not find any package by glob 'linux-headers-4.14.73-sunxi' E: Could not find any package by regex 'linux-headers-4.14.73-sunxi' what is the problem??? PS: the problem decided.

Hello and Happy New Year, From https://redirect.armbian.com/orangepi-r1/Bullseye_current I downloaded: Armbian_22.11.1_Orangepi-r1_bullseye_current_5.15.80.img.xz and installed. I see a file that shouldn't exist: $ ls -l /*core -rw-r--r-- 1 root root 16789504 Nov 30 11:55 /qemu_fstype_20221130-195503_13162.core A short while later I found this: $ armbian-add-overlay /etc/keys-h3.dts /usr/sbin/armbian-add-overlay: line 62: /lib/modules/5.15.80-sunxi/build/scripts/dtc/dtc: cannot execute binary file: Exec format error Error: dtc does not support compiling overlays There is a symlink involved: $ ls -l /lib/mo…

I'm missing something essential. I have NanoPi Neo v1.4 with Armbian 23.5 Jammy CLI (Linux nanopineo 6.1.30-sunxi). My display is Nokia5110 LCD or PCD8544 With spi-spidev DT I can successfully via `spidev0.0` with `spi-tools`. I.e. I confirm that spi is working. Now, I studied about DTO and fbtft driver, found that it supports pcd8544. I wrote this kind of DTO and added it to `armbianEnv.txt` /* * Device: LCD5110 (nokia5110) 1.6"(84x48px) SPI display Module PCD8544 * Module Connector * SDI(MOSI) <- PC0 * SCK <- PC2 * CS <- PC3 * RESET <- PA1 * DC/RS <- PA3 * LED <- PA2 */ /dts-v1/; /plugin/; / { compatible = "all…

Hi there, I have configured (successfully with NetworkManager GUI, or TUI, it was quite ago, can see it in /etc/NetworkManager/system-connections/ ) my OPi3 as an WiFi AP. (Needed this as sharing "normal" LAN traffic with video surveillance on same WiFi channel was a disaster). It works, but in "scan" on OpenWRT routers this WIFi shows only as WPA not WPA2 protected. Armbian Buster 21.02.3. Why? How to correct this? Laurent

Hello, I've flashed my SD card with Armbian_5.41_Orangepiwin_Ubuntu_xenial_default_3.10.107_desktop and after booting the system everything works like a charm except my sound which I've tried to get through the 3.5mm jack. I've done upgrade && update but that doesn't seem to help. I've tried several headphones and speakers and none of them worked. On top of that I've tried flashing this image file on one other microSD card and I've tried running it on another Opi Win Plus board since I have several of them lying around my house. Regarding my power supply, it's 5V 3A which I've read is the appropriate one. I'm fairly ne…

I run Armbian_5.30_Orangepizero_Ubuntu_xenial_default_3.4.113 in my zero. I add headset in jack， A noise start with system boot and never stop，I try play music with pygame, at first can play with noise, and system crash soon. I have to reboot it by power line.

Hi orange pi +2e with Distribution: Ubuntu 16.04.2 LTS Kernel version: Linux 3.4.113-sun8i armv7l rpimonitor installed with sudo armbianmonitor -r I use Rpimonitor to control temperature, upgradable packages and cpu frequency, nice tool ! Unfortunately it looks that rpimonitor has access to my external external hard drives, so no spin off . I change rpimonitor config files sudo nano /etc/rpimonitor/data.conf #include=/etc/rpimonitor/template/sdcard.conf and sudo nano /etc/rpimonitor/template/Allwinner_H3_Extended_Mainline.conf #dynamic.7.name=externaltemp #dynamic.7.source=/tmp/externaltemp #dynamic.7.regexp=(.*) #dynamic.…

Hi all, I recently purchased an orange pi after developing on the raspberry pi (just for convenience). I got it mainly because the integrated memory could be a real asset both because SD are faulty when making lots of memory accesses and emmc can provide a nice layer of code protection when giving the board to somebody else. I set-up everything without issue and I used the nand-sata-install to move everything to emmc...it worked like a charm. I then placed all my proprietary code on emmc and executed without issues. Problem is, I can obviously still insert an SD card and then mount the emmc and access my code since the SD is booted before the emmc.…

Hello, I have installed Armbian on my Banana M1+ and I have noticed „something“ strange in network communication. The network connector blinked rapidly even though nothing was running so I have installed iftop and found out this: iftop -i eth0 -NP Ankh-Morpork => a81.sub72.net78.udm.net Ankh-Morpork:51413 => a81.sub72.net78.udm.net:57855 Ankh-Morpork => ip70-118.245.80.crimea.com Ankh-Morpork:51413 => ip70-118.245.80.crimea.com:52026 Ankh-Morpork => adsl-225.37.6.247.tellas.gr Ankh-Morpork => ip5653f1a5.direct-adsl.nl Ankh-Morpork:51413 => adsl-225.37.6.247.tellas.gr:29932 Ankh-Morpork:51413 => ip5653f1a5.direct-adsl.nl:6881 I am won…

Not sure if this is the right forum, or it should be under board bringup.... I have a few Duo2 boards running with the FriendlyElec image, but my OrangePi boards all run Armbian... I do prefer Armbian :-) . Playing around a little I can get the Nanopi Neo Air image running, but not with the wired ethernet. (My boards reside on my own design with a ethernet jack, which works perfect with the FE/FA image) I have the Armbian build environment running in a VM, and can compile my own kernel etc. ButI need a few pointers how to get the right board config in the image/kernel.... Or... Does someone already have a build setup running for the Duo2, who is willing to …

When I login on the console, there is this display with a bunch of information, including the CPU temp. I have need to keep track of my CPU's temp, since it seems to be overheating (I have a heat sink on it, but does not seem to be enough -- I have a fan on order). I want to be able to check the temp from time to time, so I would like to run at least the part of the login banner program. What program is that? I am not seeing anything obvious in /bin.