Allwinner sunxi

Hello, [OPI PC+] u-boot : boot.scr issue Oracle VM: Linux cross-compilation 4.10.0-42-generic #46~16.04.1-Ubuntu SMP Mon Dec 4 15:57:59 UTC 2017 x86_64 x86_64 x86_64 GNU/Linux DS413J as DHCP and PXE/TFTP server with these files (copied from /dev/mmcblk0p1) on the TFTP root: boot.scr (mine but original one works well) script.bin KERNEL Same issue if i put my boot.scr onto the eMMC... Every single command works well on u-boot prompt. boot.cmd as follow, compiled with this command from Armbian doc: # OpenELEC Boot (philip63 - 02.12.2017) gpio set PL10 gpio set PA15 setenv machid 1029 …

Hello, [OPI PC+] u-boot : starting USB... don't start automatically what i did: - got 'Armbian_5.35_Orangepipcplus_Ubuntu_xenial_default_3.4.113.img' - extracted 'u-boot-sunxi-with-spl.bin' from above .img and put it on some USB key - booted from SD card with Armbian 5.35 (above) - wrote 'OpenELEC-H3.arm-7.0-devel-20161026221641-r23113-g64b34b3-opipcplus.img' on eMMC: dd if=/mnt/usb/OpenELEC-H3.arm-7.0-devel-20161026221641-r23113-g64b34b3-opipcplus.img of=/dev/mmcblk1 conv=notrunc,noerror bs=4k (boot okay without SD) - and finaly, wrote u-boot & SPL onto the eMMC: dd if=u-boot-sunxi-with-spl.bin of=/dev/mmcblk1 bs=1024 seek=8 …

Need to have working both SPI0 and SPI1 on Orange Pi Plus 2. Linux orange 4.14.40-sunxi #155 SMP Sat May 12 11:12:46 CEST 2018 armv7l armv7l armv7l GNU/Linux ARMBIAN 5.44.180510 nightly Ubuntu 16.04.4 LTS 4.14.40-sunxi SPI Double overlay installed (https://github.com/armbian/sunxi-DT-overlays/blob/master/examples/spi-double-spidev-bus.dts) I can see both spi's ls /dev/spi* /dev/spidev0.0 /dev/spidev1.0 I know all SPI0 pins - 19, 21, 23, 24 SPI1 pin CS = 8, CLK = 10 but what is MOSI and MISO? How do I know where they are (or even select) ?

I found a problem about ethernet port leds in mainline kernel, legacy kernel is fine. the ethernet port has two leds, one is link-up (green), the another one is act (orange). In Normally, the green led keep light on when cable plugged in. And the orange led keep blinking when data coming or outgoing. but in mainline kernel (4.13.16-sunxi / linux-image-next-sunxi 5.35) ethernet port leds REVERSED. the green led keep light off when cable plugged in but light on when cable plugged out. I found that problem both in a new bought opizero and an old opizero. here is a short video record

Hello, I have moved the armbian system into my usb hdd lately but now I want to move it back. How can I do this?

Hi, With an Orange Pi Zero Plus I‘d like to run a DLNA (UPnP) music server for streaming flac files - means music only - to certain clients via LAN, for instance a network AV receiver. Therefore, 100 MBit/s should be sufficient. How to limit the OPi0+ network speed to 100 MBit? And to switch off Wifi also? ... ... for minimizing power consumption. Presupposed Armbian + OMV (+ miniDLNA plugin) installed. Thanks, Joe

I have noticed a very weird problem: connection works for some time (several hours or sometimes days) and then stops. Once it stopped working (connection between my mobile app and OrangePi) I have checked on the board: - ping 8.8.8.8 - OK - ping (router IP) - OK - ping (broadcast ) - FAILED - ping (PC or any other device connected to the network) - FAILED In all cases, Wireshark captures the ping requests. Once I tried to ping OrangePi board from my PC, I see in&out ping packet on OPI board by Wireshark. It seems like some lower layer or router (the same on two different) blocks the outgoing connection. Ideas? (WiFi power management off, no fir…

Hi all, I'm new here. Since I bought my OPi One I didn't try any of the official images, but only armbian legacy kernel. The first OPi one I thought it was broken, no led on the board only the eth ones, nothing happend on the screen (homemade power cable with 1.4 plug and a xiaomi ac power adapter 5V 2A almost correctly given, tested with a multimeter). The image was burned on a 4gb kingston micro sd card with etcher formatted with sd formatter. So I bought another one, and I have the same identical issue. So, I started to study and I found out that I could connect to the OPi through SSH. So it what I tried to do all the night. Again image burned with e…

Hello friends! I Am using 3G modem(Huawei E171 connected by OTG cable) on my OPi One for internet, but one problem - modem after few days working freeze. Reboot don't help because not full power off on USB, and after reboot i don't see modem in /dev. Only after physical remove modem and install again it's initialized and work fine. Question: Can i power off USB from cli? # uname -a Linux orangepione 3.4.113-sun8i #18 SMP PREEMPT Thu Jun 15 02:16:06 CEST 2017 armv7l armv7l armv7l GNU/Linu # lsusb Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 00…

Hi all! Has anyone some experience with dts overlays for the mainline kernel 4.14.47? I connected the SHT11 temperature sensor to PA7 and PA8, installed the sht1x.dts overlay from https://github.com/armbian/sunxi-DT-overlays/blob/master/examples/sht1x.dts via "sudo armbian-add-overlay sht15.dts" and afterwards looked via dmesg into the kernel output. That's what my OPLite reports: It is a kernel IO error. The LogicAnalyzer doesn't record any pin toggle. But what am I doing wrong? Do I have to deactivate the pins in GPIO driver? Can someone please help me? As I soldered the SHT11 by myself I modified some RPi userspace code to v…

Hello Respected Supporters, After upgrading to Armbian 26 (kernel version 6.12.58), the onboard network card (end0) experienced a severe degradation in transmission performance (reduced to approximately 1/10 of previous levels). Upon investigation, it was discovered that the kernel driver (dwmac-sun8i) has locked all hardware offload features (TSO/GSO/Checksum), forcing the CPU to handle all processing in software. root@orangepi3:~# uname -r 6.12.58-current-sunxi64 root@orangepi3:~# dpkg --list | grep linux-image ii linux-image-current-sunxi64 26.2.0-trunk.48 arm64 Armbian Linux current kernel image 6.1…

Hello, I'm starting in this world with an Orange Pi Lite, but I'm not being able to perform the initial setup using serial console gadget on the OTG port. To prevent power problems, I'm using the DC input. Unfortunately I haven't found enough information to make the configuration on a Linux PC, since I wasn't able to know the /dev address to connect through screen. You've probably noticed that my knowledge of Linux is rather scarce. Thanks in advance!

Good day! I'm using latest armbian build for orange pi lite (Armbian_community 25.2.0-trunk.86 Bookworm). Tried to connect anything to OTG USB port (mouse, flash drive), but it didn't work. DMesg was silent. Had 4 USB devices: [ 1.683435] usb usb1: Product: EHCI Host Controller [ 1.699369] usb usb2: Product: EHCI Host Controller [ 1.727339] usb usb4: Product: Generic Platform OHCI controller [ 1.729832] usb usb3: Product: Generic Platform OHCI controller Then I followed this guide https://github.com/carl1961/Orange-PI-Lite-Usb-OTG-to-Host And I had 5th one after this: […

The problem I have an USB endoscope camera that works fine with my Orange Pi lite's normal USB port. However I need both USB port for other devices, so I want to connect this same USB camera, which was orginally marketed as USB otg camera for android phones, using Opi lite's micro usb otg connector. What have I tried - In armbian-config menu, I have enabled usbhost0. I believe this overlay is for the usb otg port, but just to be sure I also enabled usbhost1, usbhost2 and usbhost3. - Using dtc I decompiled sun8i-h3-orangepi-lite.dtb into sun8i-h3-orangepi-lite.dtc. - In this dtc file, I looked up musb, and changed status = "disabled" to "o…

Fails to boot after creating a swap file, it gives an error "BUG: soft lockup - CPU#0 stuck for 23s!". Help solve the problem.

I'm using Orange Pi One with ARMBIAN Debian GNU/Linux 8 (jessie) 3.4.112-sun8i. To access to UART I'm using function serialOpen() of WiringPi library. Default device name for Raspberry is '/dev/ttyAMA0'. But I can't open this device (No such file or directory). How to enable ttyAMA0?

Hi, I'm new to the Armbian/Alt PI scene, coming from a RPI Zero W. I'm needing to interact with my PI using a CH340G (is it compatible) USB to TTL dongle. I've also trjed a CH351A device, put it into UART mode. Unfortunately, I get nothing from the PI. Despite using the primary RX/TX pins. I've also tried enabling all of the UART pins using armbian-config, and using another set of pins - to no avail. Please view my setup below. I've run out of ideas of where I'm going wrong. I've tried these images: Armbian_5.90_Nanopineo2_Debian_buster_next_4.19.57 Armbian_5.90_Orangepione_Ubuntu_bionic_next_4.19.57 Refer…

I'm trying to replicate a flash drive using an ISO file. My system is running the latest Ubuntu next kernel. Here is how I am mounting an ISO: # Mount sudo modprobe g_mass_storage file=/home/pi/mini.iso # Remove sudo rmmod g_mass_storage Here are the two types of results I get from three different images. (Ubuntu net install, Need for speed 2 iso, custom made iso) It's definitely being detected. However it's appearing as either empty partitions or unallocated.

Hello All, I have Orange Pi one board with Armbian 5.20 Desktop and Kodi/mpv/mplayer installed. I want to make OP1 a home media center. Desktop is set to 1080p60 (1920x1080p 60Hz, by h3disp script). My problem: Everything works perfect when playing videos mkv (x264/h264), mpeg2, mpeg etc. for mpv, mplayer, kodi even 1080p materials. But I have a problem playing videos coded with MPEG4 (popular avi xvid). MPV config: vo=vdpau hwdec=vdpau fs=yes framedrop=vo Video looks like this: http://pasteboard.co/i5YOuOebV.jpg When I use vo=x11 and video is not in fullscreen everyting is OK, on full screen i get: LIBGL: Initialising glshim Playing: The.English.Patie…

So... second sack at the sav here. Last time i wrote i had a kingson sd card ( a low one ) but it was recomended to buy a Samsung Evo sd card instead. So after i confirmed one of the kingston sd cards was bad i more or less whent thru the warranty getting a refund for that one ( not sure why i botherd since it was so cheap ). Anyhow. Got my Samsung EVO card and tryed with DD in linux and rufus wich you guys recomend for windows and still same issue with Armbian. It boots the other distros like Debian and Ubuntu from the orange pi's webpage but no ethernet. And when i try armbian i get the uboot text thru the ftdi but it does not find any boot device. U-Boot SPL 2016.…

On Orange Pi PC +, usbmount is installed but USB memory is not recognized. How can I determine if it is a device issue or a software configuration problem? (Version 5.23)

Hi. The following happened. When power is suddenly cut off in emmc, the file contents created by fopen (), fprintf (), fflush()　and fclose () are not saved after rebooting. It seems that it has not been physically written out while being cached. If display the file before cutting off the power, the contents are correctly saved. In addition, if it is normally reboot it is saved correctly.

So, hello. Sorry for bad/broken English, I'm still teaching it. As in title, I can't boot my orange pi 2 plus from sd card. I have tried with one tv(hdmi-hdmi 1920x1080), and one normal pc monitor (hdmi-dvi 1440x900) sd card is 8gb class 10 producent "team". I burned my image with Etcher 1.1.1 Funny is that, lubuntu image from eMMC is working fine, I've tried to boot lubuntu, ubuntu, image, with no effect, the only image that works is from eMMC(i have installed it months ago) At start, the green LED lights up and after 5, maybe 10 seconds red LED is blinking, something like blink-blink-2/3 seconds break-blink-blink I feel like I should create this …

Dear friends, I have a problem with the ethernet connection of my orange pi plus 2e. The connection was working normally and stopped, I can only access through the wi-fi. I already researched it and found no solution. Open the connections and pressing ifupdown (eth0) the following error appeared: (1) Creating object for path 'org / freedesktop / NetworkManager / ActiveConnection / 14' failed in libnm-glib. Is there a connection to this error with a lack of ethernet connection?

Greeting, I installed the OrangePI plus image (desktop) on my Orange PI plus2. It seems to work fine but I can't get any video output. I tested with several h3disp settings, with a HDMI to VGA adapter then with an HDMI to DVI adapter, and finally on the A/V port. I have no hdmi screen to test direct connection without adapters. Ideally I would like to use the HDMI to VGA adapter. any ideas ?

Dear friends, my orange pi plus 2 was working properly Armbian but now it does not recognize the wifi nor the internet cable. I did not make any changes to the system. Does this solution solve this problem? If I decide how to install these files on the card?

Hello, I know that armbian for orangepi prime is under development. Armbian does not detect the integrated wifi, and I'd like to know if it's not implemented yet or it's happening just to me

I run the OPi Zero as a Pihole with etherned, and I would like to minimize power consumption as low as possible. 1. I did change the frequency to be between 120 - 960 Mhz, and ondemand. This probably reduces power and heat too. 2. I'm not sure how to disable USB (I don't need it at all) and WiFi. I read the threads, like this but not sure how to do. Can you please guide me? 3. I saw there are other options too, with a tool h3consuption, but I don't know how to install it and what can I do to squeze down a couple of mW's more. Your help is very much appreciated!

After nearly one year of kernel crashes, I finally found the stable configuration for Orange Pi Zero 3 as a 24/7 SDR server. The critical discovery: legacy kernel 6.6.75-sunxi64 is the only stable option. The current kernel crashes within hours under SDR load. Additional fixes: - Blacklist aw859a WiFi driver (causes kernel instability) - Blacklist DVB modules for RTL-SDR - Lock libairspyhfSupport.so with chattr +i (SpyServer/SoapySDR conflict) - Mask systemd-networkd-wait-online - CPU governor: schedutil - usbcore.autosuspend=-1 for USB SDR dongles Running 3 SDRs simultaneously: RTL-SDR Blog V4, …

Hi, I'm having some instability issues with WiFi driver on Orange Pi Zero Plus, it uses RTL8189FTV instead of buggy XR819 chip. Some times it just works fine, but that's not always the case, some times when I turn on the board the driver is not able to turn on the WiFi chip, and it keeps stuck in a limbo state... The kernel identify the network device as (wlan0), but it's impossible to turn on or connect to any network. sudo dmesg | grep -Ei '(8192eu|rtl|wl|realtek)' [ 236.057560] RTL871X: Failed to init Power On! [ 236.057567] RTL871X: rtw_hal_init: hal__init fail [ 236.057573] RTL871X: -ips_netdrv_open - drv_open failure, bup=1 [ 236.057579] RTL8…

Hello. I have an Orange Pi Zero board with Armbian on it. I want to use its serial pins for flashing arduinos. Right now I only have 1x3 serial pins and 1x13 media (?) pins soldered, the 2x13 GPIO doesn't have any pins and I don't have any spare ones to solder (alright, I might have some, but I'm too lazy for that). That means I only have access to UART0 pins which are currently reserved for Linux console. With RPi Zero and Raspbian the same problem was solved by simply removing "console=ttyAMA0,115200" from kernel options. However, Armbian seems to generate kernel options entirely from armbianEnv.txt, making it impossible to manually remove ser…

Hi there, My question is to Orange Pi Zero owners. I've read is has DDR3 RAM shared with GPU. What is a minimum value of GPU memory? I'm looking for headless setup so it would be good to know how much memory can be used by OS. Thank you in advance.

Hello, I have done my iso with script yersterday and when I start the Orange Pi Plus 2 the yellow led appear but nothing else doing ... Why ?

Hello, I want to branch a disque that have 3to or 4to to do my personnal backup of data. Can I do this ? Can I branch it in the usb and do this ? I format in ext4 ? or ntfs ? (with gpt mode). Thanks

Hi, I'm Rosario and I'm a new Armbian follower. I liked it. After months using my OPI Plus2 with Ubuntu Jessie Loboris image (and installed it also on emmc) I decided to install Armbian. I need to say last time I installed OS on emmc I received an error. Erase was fine but copy of last jessie Image no. After that I Installed Armbian Image with no problem and after some reboot OS run up fine. I downloaded last Armbian Image (3.4.112 kernel version). Now, when I try to use emmc I receive some error. First of all seems it's missing. I see only mmcblko (my SD card). emmc doesn't exists: root@orangepiplus:~# cat /proc/partitions major minor #…

Today i compiled for my Orange Pi One the kernel 4.11.12-sun8i from the sources. The kernel works with only 1 (one) core. / _ \ _ __ __ _ _ __ __ _ ___ | _ \(_) / _ \ _ __ ___ | | | | '__/ _` | '_ \ / _` |/ _ \ | |_) | | | | | | '_ \ / _ \ | |_| | | | (_| | | | | (_| | __/ | __/| | | |_| | | | | __/ \___/|_| \__,_|_| |_|\__, |\___| |_| |_| \___/|_| |_|\___| |___/ Welcome to ARMBIAN 5.31 stable Debian GNU/Linux 8 (jessie) 4.11.12-sun8i System load: 1.11 0.26 0.09 Up time: 0 min Memory usage: 10 % of 464MB IP: 192.168.3.156 CPU temp: 43°C Usage of /…

Hello, I do images of Debian Jessie with Desktop anf in the end it do image but I have : [ o.k. ] Installing desktop-extras for sunxi [ sunxi ] E: Impossible de trouver le paquet libdri2-1 dpkg: des problèmes de dépendances empêchent la configuration de mpv : mpv dépend de libbs2b0 ; cependant : Le paquet libbs2b0 n'est pas installé. mpv dépend de libcdio-cdda1 (>= 0.83) ; cependant : Le paquet libcdio-cdda1 n'est pas installé. mpv dépend de libcdio-paranoia1 (>= 0.83) ; cependant : Le paquet libcdio-paranoia1 n'est pas installé. mpv dépend de libfdk-aac0 (>= 0.1.1) ; cependant : Le paquet libfdk-aac0 n'est pas installé. mpv dépen…

Hello, I want to have a image on boot and no text. (splashcreen) I see plymouth but I don't now if it done with it and when I can install in to my OrangePi Plus 2e Anybody can help me ? Thanks a lot.

Hello, I am trying to staert the card with empty micro sdcard. The system is into eMMc. But when the micro sd card is in the Orange Pi and branch it it not start it failed with message error no system. Why ? I can't start the Orange Pi with a blank sdcard ? Thanks

Hey folks! On monday I was able to fix the overscanning issue of my Orange Pi zero (read here). Because fiddling around with the register values can be pretty harsh some times I decided to created a small programm to move the picture of the composite video output. You can find the project page here: https://projects.nwrk.biz/projects/allwinner-tvout With this tool you can easily move the picture relative to its actual position by just calling : $ sudo tvout -m -x <value in px> -y <value in px> To reset the position you can use: $ sudo tvout -r I hope some of you may find this useful. If I have enoug…

Hello everyone! I am designing a PCB and I need to know if there is a possibility to swap SPI0_CLK and SPI0_CS by changing this line from: pins = "PC0", "PC1", "PC2", "PC3"; to pins = "PC0", "PC1", "PC3", "PC2"; Currently I don't have a board to check it myself. Any ideas if this would even work? Thanks!

Hello everyone. I encourage you to write these lines after I spend all day reading and trying to solve the problem without success. Knowing that there are other many post about, I write this new that existing ones are already very old and refer to applications and concepts that no longer exist in the latest versions of ARMbian. The fact is that I bought a new OrangePi Lite with a new SDHC Clase10 (80MBs) SanDisk and basically not I connect to the WIFI 2.4 g connection of my house where work perfectly without any problems other Zero OPI and OPI PC + with ARMbian 5.35 Ubuntu. The summary problem is it asks me again the password and does n…

Good time of day fellows. How can I mount SD card to transfer data into when Armbian 3.35 Ubuntu 16.04 started from flash? Cant see SD card nor mount it. Installed USBmount and it works with USB flashes on OTG port but no with SD card. Thanks to anyone for advice. Additional info: NanoPi Air 32Gb eMMC http://sprunge.us/OLNS

Dears, We have 4 boards Nanopi Neo2, but when we connect to energy, they don't boot, leds of net port (green and yellow ones) and internal led (red) are on all time. We tried to access via serial port (using an usb-serial adapter), but they not show any boot process. We tried some different boot images on sd card. Nothing works. All four devices are in this situation (and they are new!). There is any thing we can do?

Hi, I'm Olivier, french engineer, and i have bought an orangepi plus card in april. I use linux (x86) since 1994 Sorry for my bad english ... I was happy to find Armbian because linux images provided by xunlong have many security problems (example / and all system directory aren't owned by root but by orangepi user). Thank for your work on Armbian. My Orangepi + has been installed with a 5.10 armbian image (Armbian_5.10_Orangepiplus_Debian_jessie_3.4.112) and run perfectly. I wanted upgrade to 5.20 and since the card doesn't boot anymore. I can boot with the native android on NAND memory but I can't boot on SDcard. When I boot on sdcard, only gr…

Hi there. @Moderators: sorry for double-posting, started here: https://forum.armbian.com/topic/13916-cubietruck-allwinner-a20-spidev-no-such-device/?do=findComment&comment=101122 but might be the wrong section and been overlooked by "cubietruckers". Feel free to delete the one over there. @Moderators: could you verify my account please so that I can edit my posts after posting on the same day? I'm human, I can tell traffic lights from trees, cars, and trucks ;-) Cubietruck. Stock image 20.02. apt-upgraded to 5.4.35-sunxi EDIT: NOTE: just checked the armbianmonitor upload result, which says "5.4.20" at the top - but "…

Hello, I want to use for my domotic a USB Everspring sa413 (Z-Wave modem based on ZM5304), but this device is not detected on Armbian with my Orange Pi Zero h2+. https://fccid.io/D87-ZM5304-U/User-Manual/User-Manual-pdf-2052478 Normally, I think this dongle is use like CDC/ACM device but I don't understand what wrong because ACM module is loaded. I use actually Debian Jessie next 4.13016. root@orangepizero:~# lsusb -t /: Bus 08.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M /: Bus 07.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M /: Bus 06.Port 1: Dev 1, Class=root_hub, Driver=ohci-pla…

So iwe been trying to solve this issue by experimenting and iwe hit a wall where i do not know what to do so i guess i'm just hoping someone would spot what i'm doing wrong. So i bought an "Orange Pi PC" from ebay and i'm trying to set it up without much sucess. I downloaded the "Armbian_5.14_Orangepi2_Ubuntu_xenial_3.4.112.raw" image from the armbian webpage. ( I also did my Cubieboard wich worked fine with the same steps. ) The commandline i used to write the image to an sdcard is this: sudo dd if=./Armbian_5.14_Orangepi2_Ubuntu_xenial_3.4.112.raw of=/dev/sdc bs=1M oflag=direct sudo sync And then i unplug the sd card and put it into my OrangePi and when it boots the g…

Hello, I'm having problems trying to boot armbian (Armbian_20.05.2_Orangepiplus2e_focal_current_5.4.43.img.xz) on this Orange Pi Plus 2e board. I'm using a fast original samsung 32gb sd card and I've tried multiple power adaptors. Here's the output from the serial console: U-Boot SPL 2020.04-armbian (Jun 03 2020 - 07:59:25 +0200) DRAM: 2048 MiB Trying to boot from MMC1 U-Boot 2020.04-armbian (Jun 03 2020 - 07:59:25 +0200) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi Plus 2E DRAM: 2 GiB MMC: Device 'mmc@1c11000': seq 1 is in use by 'mmc@1c10000' mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c11000: 1 Loadin…

Hey everyone, First off, I don't use Linux often so please bear with me if I miss out on obvious things. I have a few Orange Pi Lite boards, and after booting up Armbian 5.14 I was excited to give the Wifi a try after only having ethernet on my Orange Pi One boards. My OPi Lite sees my network just fine, but when I put in my credentials and go to connect to it, it fails returning "Bad Password". For what it's worth, I've checked the password probably 25+ times, I promise it's right. The wifi WILL connect to open networks, however. Is there some obvious solution that I'm missing here? Any help or direction would be appreciated. Thanks!

Is it possible to shut down power to a particular USB port? I have a sensor that is using USB also to power itself. I don't need it running all the time - hence - I'd like to turn it off.

Hi, I'm trying to boot from SATA the original OrangePI: Using the Jessie "Linux orangepi 4.9.12-sunxi #4 SMP Thu Feb 23 19:46:51 CET 2017 armv7l GNU/Linux" Followed this thread: https://forum.armbian.com/index.php/topic/329-moving-linux-to-sata-or-external-drive/ - copied to /dev/sda1 - edited /boot/boot.cmd and changed to /dev/sda1 - edited the mounted sda1 fstab and changed / to SATA drive UUID - compiled: mkimage -C none -A arm -T script -d /boot/boot.cmd /boot/boot.scr Rebooted but Orange Pi still boots from mSD card and does not use SATA drive. Question: Should I use UUID of the SATA drive in /boot/boot.cmd?

Hi, I have flashed Armbian_5.35_Orangepilite_Ubuntu_xenial_default_3.4.113_desktop.img - and it works fine with my Orange Pi Lite v.1.1 But if I flash Armbian_5.38_Orangepilite_Debian_stretch_next_4.14.14.img which is aslo supported, the device does not boot. At least I get no output on HDMI, and no serial console over OTG. So I cannot check if it does not boot at all, or dies somewhere in the middle How can I check why it does not boot?

Hello! I recently started setting my board up, and came across all the information needed to enable the LCD use for it. For info, I've updated to 5.20. I have gone through the whole process to change the script.bin to fex, edit, change back, copy and sync. The changes are saved, I have even made a copy of the script.bin to script.fex in order to see if the new script contains the changes I made. All is there. It seems to be the problem another user had in this thread: http://forum.armbian.com/index.php/topic/841-bananapro-lemaker-5in-lcd-legacy-kernel/ In this case I chose the lcd_if=4 since it is what they provide at sunxi, but it didnt work. I then ch…

I recently ordered 3 A20-OLinuXino-LIME2-e16GB devices (with 16GB eMMC) and received rev. K boards. Unfortunately, I have troubles with both "official" Olimex eMMC rel 16 image and latest (as of last week) Armbian Stretch images. Both images booted fine from SD card (also tried multiple SD cards, one of them bought from Olimex ) and I was able to run the emmc.sh / nand-sata-install scripts fine. Now the troubles started as I turned off the device, removed the sd-card and tried to boot from eMMC. All 3 boards had entered FEL mode. From fel mode I was able to use the `sunxi-fel` utility and push the uboot fine... Initially I was able to g…

Hi, I'm new with Armbian, have some experience with Raspberry. I have succesfully installed it on a bananaPi. uname -a Linux bananapipro 4.4.3-sunxi #19 SMP Tue Mar 1 21:34:52 CET 2016 armv7l GNU/Linux Then I have installed Logitechmediaserver with dpkg -i logitech....deb It runs well, but after a reboot the installation is not there anymore. /var/lib is default, the init.d-script is also not there. Any hints? Edit: I have the message for 19 updates, so I made apt-get update After reboot, all updates are gone and I get the message for the 19 updates again. Regards DoXer

Cannot open this file: http://mirror.igorpecovnik.com/Armbian_5.14_Orangepi_Ubuntu_xenial_4.6.2.7z From http://www.armbian.com/orange-pi/ MD5 is: aed2af7290cc645ba7282d5fa78766a9 Please, reupload it

So I'm back again! - The guy with the Banana Pi's he thought were Banana Pro's. I went and bought one of those stubby little WiFi dongles...fairly generic, Realtek 8192cus...but still (can't believe I'm saying this in public) can't get it up. I'm super frustrated. My current project with these boards is to set myself up some magical WiFi "security" cameras. Everything else works. Webcam works, "motion" detects and records, a little nodejs app manages some scheduling stuff, ssmtp sends me video recordings....but this blasted WiFi!! Help? I'll comment shortly with some technical details/diagnostic dumps(busy re-writing my backup img …

I recently switched from a Raspberry Pi 2 running Arch Linux to a Banana Pi (the original) running Armbian for music streaming using MPD. My output device is an XMOS-based Gustard U12 asynchronous USB transport feeding my DAC via AES/EBU. Using Armbian on the Banana Pi, all my 24-bit/192kHz music is being played back as 24/96, according to the display on the transport and DAC. All other sample rates (44.1, 88.2 etc.) are being played back in their native sample rates, as expected. Is ALSA on Armbian system-wide limited to 96 kHz? I have never had an issue like this before, and I don't know where to begin in regards to troubleshooting. I'm guessing th…

[EDIT: The solution to this was realizing I'd been handed Banana Pi's (which have no WiFi), not Banana Pro's (which do have WiFi). I wasted a few days on this.] Hey guys, I'm sure you're sick of hearing this, but I have no WiFi with latest Banana Pi Pro image. No errors in dmesg, lsmod shows "brcmfmac" is present, but no device in iwconfig.

I'm having trouble getting the RaZberry zwave extension board working in Armbian 5.31 with the mainline kernel. Previously on Bananian I just symlinked ttyS2 to ttyUSB99 and I was able to use the RaZberry with OpenZwave. But now, I have no idea how to get it working. I guess it has got something to do with overlays for the kernel but I haven't been able to find out exactly sifting thru the internet... Help very much appreciated.

I supose the armbianmonitor output doesn't help much. But here is an output from serial console: 3 times reseting before.... resetting ... U-Boot SPL 2021.04-armbian (May 06 2021 - 20:01:01 +0000) DRAM: 1024 MiB CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 Trying to boot from MMC1 U-Boot 2021.04-armbian (May 06 2021 - 20:01:01 +0000) Allwinner Technology CPU: Allwinner A20 (SUN7I) Model: LeMaker Banana Pi I2C: ready DRAM: 1 GiB MMC: mmc@1c0f000: 0 Loading Environment from FAT... Unable to use mmc 0:1... HDMI connected: Setting up a 1920x1080 hdmi console (overscan 0x0) In: serial Out: vga Err: vga Net…

System: armbian, BananaPi Pro, sd card, sata ssd, usb hdd I manually moved my existing armbian system from sd card to a sata ssd. Then I changed the rootdev in armbianEnv.txt to the ssd´s UUID. After reboot I thought everything was ok. Then after a system update I figured out that the kernel version differs from the installed kernel modules. I think the new kernel and the modules are installed in /boot at /dev/sda whereas the kernel still boots from /dev/mmcblk0p1. How can I fix this? Here some information: root@pi-nas:/mnt/boot# lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT sda …

Hi I want to install some packages, but it not found on sources. When i do update repositories by sudo apt update command, the following messages shown that means the repositories is broken. Err:1 http://httpredir.debian.org/debian stretch InRelease Could not resolve 'httpredir.debian.org' Err:2 http://httpredir.debian.org/debian stretch-updates InRelease Could not resolve 'httpredir.debian.org' Err:3 http://httpredir.debian.org/debian stretch-backports InRelease Could not resolve 'httpredir.debian.org' Err:4 http://security.debian.org stretch/updates InRelease Could not resolve 'security.debian.org' Err:5 http://apt.armbian.com stretch InRelease Could …

Hello everybody. Faced such a problem. When connecting to the HDMI port of the monitor, no image is displayed on the monitor. More precisely, the line at boot time is visible, but the desktop is not displayed. If you connect to a TV via HDMI port, there is an image. I connect OrangePi Plus 2, via HDMI-HDMI cable. Monitor LG FLATRON 27EA33V-BB. Why is that such a problem on armbian and retroorange assemblies. But the assembly of DietPi on the monitor image displays .. The systemist under win7 also without any problems displays the image always. Tell me where to find the solution to the problem. I tried changing the modes with the 'h3disp' utility. Screenshot - https:…

Hello, I received a few weeks ago some new Lime2 boards. Using compiled Armbian kernel leads to a network problem: no IP is set and network does not work I have messages when connecting Ethernet cable: sun7i-dwmac 1c50000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx Link is Up - 100/Full The ip a command gives: 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000 link/ether 02:02:02:cc:cc:cc brd ff:ff:ff:ff:ff:ff inet6 fefe::fe:xxx:xxx:9307/64 scope link valid_lft forever preferred_lft forever I think the problem is related to the new revision of the board as described here…

When installing snaps I get the following error: error: system does not fully support snapd: cannot mount squashfs image using "squashfs": mount: /tmp/sanity-mountpoint-910419852: wrong fs type, bad option, bad superblock on /dev/loop0, missing codepage or helper program, or other error. It worked about a mouth ago but now whenever I build the images and try to install a snap I get that error. Steps to reproduce: 1. Build Nanopi Duo2 image with kvm and squashfs 2. Connect to device and install snapd 'sudo apt install snapd' 3. Install snap to test it 'sudo snap install hello-world' Expectation: …

Greetings all. I've bought an Orange Pi PC recently, along with this screen, and I wanted to make the touch screen work on it. I have tried following this tutorial and this one, but so far I was only able to get the screen working. Currently installed image is: Armbian_5.35_Orangepipc_Debian_jessie_default_3.4.113. When I run `evtest` the only devices detected are `vmouse`, `sunxi-gpiokey` and `sunxi-ths`. I tried installing a GUI with xorg, lightdm and xfce. To show the GUI on the display I am using the following command: FRAMEBUFFER=/dev/fb8 startx But touch still isn't working. This is the output of armb…

Hi all! I have an Olimex Olinuxino-Lime2-4GB A10 cpu based dev board and I have installed Armbian on an SD card. Everything works fine, except when trying to compile some drivers for the wifi dongle that I want to use. The dongle has an RTL8188CUS chip, and I also have another dongle with an RTL8192CU chip, and when following the instructions found here the compilation fails, because of the kernel headers missing. The instructions work fine on other distributions. Could someone help me figure out how to successfully compile the drivers? Where can I get the kernel headers? I really need these drivers for my project.

Hi, Noobee here. I'm using a NanoPi NEO with the latest legacy image updated. Using ssh to access device. Linux Lap 3.4.113-sun8i #4 SMP PREEMPT Wed Nov 22 13:45:28 CET 2017 armv7l armv7l armv7l GNU/Linux In the journalctrl log I'm getting repeated failures for ntpd and cron about every minute. 1) The router that I'm connected to is IPv4 only. In nmtui I'v set the connection to ignore IPv6, but it seems that IPv6 has not been disabled. A IPv6 IP address has been assigned to the wireless interface. Should I be doing something else? 2) Cron is constantly doing something with armbian-updates. Is this normal…

Hello Maybe it will help someone. I lost a lot of time trying to connect 1-wire to Cubieboard2 via DVK 522 (it has DS18B20 connection on PB10 /gpio 66/ with external pullup). I've done steps in http://linux-sunxi.org/1-Wire with different combination and it doesn't work. In /sys/bus/w1/devices i had only sth like 00-80... 00-40... 00-c00.. without w1_slave file (i was 100% sure of hardware - it works on waveshare debian image) SOLUTION: In /boot/armbianEnv.txt lines needs to be without comments: and that's it ( overlays are created automatically by config so it will be sth like for…

Hi All, I did upgrade of my Cubieboard 3 from 5.31 to Armbian 5.36 and everything was fine. But than by short system audit I find an old package "rpimonitor" that was used long time before and never being used now. I did "sudo apt purge rpimonitor" and "sudo apt autoremove" to remove dependencies and it starts... Somehow my CPU load was vanished, on Idle mode it shows at least 2.0+ and at least 4+ on load. Looks like it is twice higher than it is. If I run top command, nothing shown. Only mysql time is 117+ Hours. But, Idle is 98.7... :~$ top top - 19:29:50 up 22:07, 3 users, load average: 2.28, 2.35, 2.93 Tasks: 112 total, 1 running, 111 sleeping, 0 stopp…

Hello, I've been trying to use DNSCrypt on ARMBian Debian on OrangePi Zero. I'm following this guide (exact revision link for future reference), and it was working great on Raspbian in Raspberry Pi, When I try the same guide, it compiles, installs successfully, runs the daemon, however it doesn't actually work, saying "connection timed out; no servers could be reached". When I'm not using daemon, and run manually, this time it says "Unable to bind (TCP)". But when I compile and use in Ubuntu, it works nicely. This is my GitHub issue on DNSCrypt repository, including all my tests and inputs: https://github.com/jedisct1/dnscrypt-proxy/issues/561 …

I configured the on board wifi access point on my Orange Pi Lite, (WPA / WPA2 encrypted, hostapd, dnsmasq). Everything was fine. I could power the board, connect to its wi-fi and ssh into it. Just a day ago I connected to the board with ssh, just to test that it was working and closed the connection immediately. So I know that it should be working and that all the configs are good. But now I keep on getting Connection Timed Out error, tested under Arch Linux and Mac (as the connecting clients). Under arch linux my card finds the wi-fi, finds its bssid and gets to sending an "ASSOCIATING" request which gets a Timeout response. It does not seem to be a hardwa…

Hey guys I'm setting up a Cubietruck with Armbian_5.04_Cubietruck_Ubuntu_trusty_3.4.110_desktop.zip, and I cannot mount any of my unmounted volumes. Installing gksu didn't fix it. Any tips?

Hello, I'm following my investigation to make possible an Open Hardware & Open source solution for schools (cf. https://forum.armbian.com/index.php?/topic/4929-which-card-choose-to-deploy-an-educational-open-source-os-in-schools/&tab=comments#comment-37422 ) I can't use the WiFi. I didn't found information on the forum for Orange Pi PC+ on board wifi (found some but it was for USB wifi). I have downloaded Ubuntu desktop – legacy kernel on https://www.armbian.com/orange-pi-pc-plus/ and installed it on class 10 SD card with Etcher ( Armbian_5.30_Orangepipcplus_Ubuntu_xenial_default_3.4.113_desktop.img). I'm using 3A 5V power …

I've installed Armbian again. Initially I logged in as root and 1234 password which worked. Then it asked to change the password. Something wen't wrong with it. My OrangePi PC boots fine and ok. When I open a terminal and try to do a "sudo this that" it asks my password and won't accept the one I gave, nor 1234. I've done the full installation a couple of times and same problem persists. How do I rest root password? The problem is that everytime I re-install everything and I'me at the very firts log (where I enter root and 1234) the screen scrolls so that I cannot see what it is asking since my monitor is 1600x1024. That I why I need to reset password afterwards. I…

Hello, I'm trying to have the onboard bluetooth working with OrangePi PC+ (to evaluate OPPC+ to deploy it in school with open source OS and software cf. https://forum.armbian.com/index.php?/topic/4929-which-card-choose-to-deploy-an-educational-open-source-os-in-schools/&tab=comments#comment-40408 ). I'm using the ubuntu desktop legacy version that we can download on https://www.armbian.com/orange-pi-pc-plus/ Here is the result of armbianmonitor -u : http://sprunge.us/WeEO If I'm running bluetooth in command line I have this problem : La connexion à BlueZ a échoué (The connexion to BlueZ failed) Le démon Bluez …

Hello, I'm following the investigations for the project of open source and open hardware solution for schools (https://forum.armbian.com/index.php?/topic/4929-which-card-choose-to-deploy-an-educational-open-source-os-in-schools/). Wifi, ethernet, bluetooth, localization, using VGA screen, is working, arduino IDE can upload code with ubuntu desktop armbian legacy, that's really cool. Now the next step is to make possible to the children to make 3D modeling with code, so they will learn coding & mathematics making toys OpenScad 2015 is very nice for that (OpenScad 2014 not enough, a child that has tried openscad 2015 don't…

Good day, I use prebuild Armbian Stretch mainline kernel 4.14.y. And I want to connect pcf8563 rtc through i2c protocol on TWI1_SCK/PB18, TWI1_SDA/PB19 hw A20 pins. pcf8563 slave address is 0x51. If by default, no i2c are enabled through overlays= in armbianEnv.txt, I still get i2c-1 device with addresses 0x51-0x57 occupied: root@lime2:~# ls /dev | grep i2c i2c-0 i2c-1 root@lime2:~# i2cdetect -y 0 0 1 2 3 4 5 6 7 8 9 a b c d e f 30: -- -- -- -- UU -- -- -- -- -- -- -- -- -- -- -- root@lime2:~# i2cdetect -y 1 0 1 2 3 4 5 6 7 8 9 a b c d e f 50: UU UU UU UU UU UU UU UU -- -- -- -- -- -- -- -- If I enable i2c1 through over…

I have a encrypted external hard drive connected via USB. I want to be able to automatically access it after boot so I made a keyfile that I put in /etc/crypttab. After updating the crypttab file I ran update-initramfs -u. But after reboot the drive is still locked. Why is this? I suspect it might be because of the order of things at boot. Maybe crypttab is called before the USB device is initialized? Any help would be appreciated. Edit: I had a incorrect crypttab that's why it didn't mount. It works now thanks!

Hello, JiveLite would be nice for LMS-installation with Touchscreen/Display. http://forums.slimdevices.com/showthread.php?98156-Announce-JiveLite-cut-down-squeezebox-control-application Has anyone of you ever successfully compiled JiveLite? TIA Jochen P.s.: With a little help from google translator. Edit: Well, I did it!

Hi, I'm testing the new Rev.K board and facing troubles with uplink performance. Downlink is ok. I already asked on Olymex forum but no response so far. $ iperf3 -c 192.168.0.110 Connecting to host 192.168.0.110, port 5201 [ 4] local 192.168.0.104 port 45700 connected to 192.168.0.110 port 5201 [ ID] Interval Transfer Bandwidth Retr Cwnd [ 4] 0.00-1.00 sec 3.59 MBytes 30.1 Mbits/sec 708 4.24 KBytes [ 4] 1.00-2.00 sec 4.14 MBytes 34.8 Mbits/sec 964 2.83 KBytes [ 4] 2.00-3.00 sec 4.19 MBytes 35.1 Mbits/sec 956 2.83 KBytes [ 4] 3.00-4.00 sec 4.16 MBytes 34.9 Mbits/sec 944 2…

Hi, I installed a armbian on Orange pi PC. The initial screen shoot is: After I upgradeed the system: I want to use DS18B20 sensor; so I loadeed this driver: but I see this message error: Why ? How to I can to resolve ?

Hi, Since the armbian release 5.3.6 (Linux 8 jessie 4.13.16-sunxi64) does not contain the module 'nls_utf8', one can not use the OpenMediaVault - OMV - plugin 'Remote Mount' for accessing an external HDD ... for example, which is connected to a Fritz!Box (running Fritz!NAS). Further details please see OMV - Remote Mount: How to mount an HDD that is connected to a Fritz!Box 7490? Please include the module 'nls_utf8' (and maybe some more nls_* modules) in an update compilation, which is based on the same kernel. Many thanks in advance. The module is provided in following Debian Jessie file list (image): https://packages.debian.org/jessie/…

Hi, I am fairly new to the SBC board and struggling to begin my setup of the NanoPo NEO Air. This little board is a perfect fit for my project I need to develop. The first problem I encounter is the following: There are no HDMI port. Thus I can't do the basic configuration for my network and allow an SSID access. Does anyone has a solution to preconfigure the WIFI of my Armbian from windows (or Linux if needed)? My second problem will be: I would like to install my system on the EMMC flash to not be dependent of the SD card. Can you confirm I would only need to run the command "nand-sata-install" when I will get…

Hi all. I build Armbian for "orangepipcplus" as described here: https://docs.armbian.com/Developer-Guide_Build-Preparation/ After build finished, I've got Armbian_5.24_Orangepipcplus_Ubuntu_xenial_3.4.113.img image, flash it to SD card, and my OPi starts well, thanks! All things that necessary for my work tasks - works fine: USB, USB OTG, WiFi, but... no Ethernet :-( When I plug Ethernet cable into my PC and OPi - no LED blinks at both sides (but Ethernet on PC 100% works, tested with Raspberry Pi, for example). In console kernel logs I see the following: [ **] A start job is running for Raise network interfaces (26s / 5min 6s) And OPi actually wa…

EDIT - UPDATE 'apt-get upgrade' worked fine - thanks to all armbian developers and contributors! --- Hi, Should I wait for 'apt-get upgrade'? ... never change a running system ;-) Due to Ethernet Port (LAN) related issues that effect OPI0+ to the newest Armbian release - under development (Now it seems that the OPi Zero Plus is missing his Ethernet-device ...). My OPI0+ is only connected via LAN cable to the router. And I don't like to use Wi-Fi (WLAN). Regards, Jochem

Was playing around with a well tuned system, wanted to upgrade my kernel - but seem to have broken something. I was on 5.37 - manually upgraded to stretch and everything was working quite well. Today tried upgrading my kernel, and was playing around with `armbian-config` to switch kernels, but didn't go so well. After a reboot had no network. Plugged in the serial console, and was greeted with the following. pi@orangepione:~$ uname -a Linux orangepione 4.11.12-sun8i #2 SMP Wed Nov 22 13:50:32 CET 2017 armv7l GNU/Linux pi@orangepione:~$ dpkg-query -W -f='${Version}\n' linux-stretch-root-orangepione dpkg-query: no packages found matching linux…

Hello everyone I just bought an orange pi zero (512mb) and installed ubuntu xenial ... I was able to connect to my wifi AP using nmtui, and now I am trying to "share" the internet with any device that is connected in eth0 ... I followed many tutorials and read several threads, but without success. My settings are defaults, I installed ubuntu xenial, just gave apt-get update and upgrade I would be grateful if anyone could help me ... thank you.

I configured Armbian on a mSD card and decided to try and move it to the eMMC. I used the nand-sata-install utility, All files from the mSD card are copied, and the last step fails. I get Error: no u-boot package found, exiting Any pointers?

It took me some time to figure how to make it work, so I decided to save it for some poor soul who would need it in future. (I am a Windows guy so this stuff is a bit alien for me). I bought <$2 WiFi dongle for my new Orange PI PC from here: http://www.aliexpress.com/snapshot/7899695282.html?orderId=76846564349160 I am running latest "ARMBIAN jessie 3.4.112-sun8i". The chip was detected by the OS but didn't work: lsusb gave me this: Bus 004 Device 002: ID 148f:7601 Ralink Technology, Corp. I tried several solutions: installing "firmware-ralink" package, compiling various sources and getting "loboris kernel" using code from this git: https://github.co…

I installed Armbian xenial 3.4.112 on an Orange Pi PC in July of 2016. It ran non-stop until sometime in February. I realized it was no longer sending data to the internet. When I checked, the Orange Pi PC was still powered. However, the green+yellow ethernet LEDs were both blinking together at what looked like 2sec intervals. After only a short time of running, the CPU was already 84C. When I originally had put the Orange Pi PC into service, it would remain close to 43C. I connected a monitor and keyboard. It booted and a look at syslog showed the eth0 was looping on `DHCPDISCOVER`. I tried `ifconfig etho down` and `ifconfi…

------------------------------------------------ **** RESOLVED **** ---------------------------------------------------- 20 years of experience in computer science and I look like an idiot front of my OrangePI PC... You want to have a working HDMI LCD SCREEN with your ORANGEPI PC and you want to learn fast… Read this small tutorial, sorry my english it not perfect and if I make some error during this tutorial, please admin just correct me inside the post. First of all, if you think you know something when you receive your orangepi haha, clear your memory my friend, orangepi is not a pc … is not a RASPBERRY so don’t try RASPBERRY tutorial …

I have found other treads that address "tv out not working" but none have been applicable. They point to files that are not on my system. It is an older orange pi zero. I have installed the latest armbian image. Here is the "lsb_release -a" return: Distributor ID: Ubuntu Description: Ubuntu 20.04.2 LTS Release: 20.04 Codename: focal I am currently operating headless and the login splash screen says "Welcome to Arbian 21.02.3 Focal with Linux 5.10.21-sunxi" I am trying to use the 13 pin connector. Pin 2 = ground (shield) and Pin 9 = video signal (center conductor) I have found forum threads about enabling the tv out bu…

I just installed the latest Ubuntu Bionic Image with 4.x kernel, fully updated and upgraded. On Orange Pi Zero 1.4 512MB + IO expansion kit board Armbian 5.75 Ubuntu 18.04.2 LTS Linux orangepizero 4.19.20-sunxi #5.75 SMP Sat Feb 9 19:02:47 CET 2019 armv7l armv7l armv7l GNU/Linux `cat /proc/asound/cards` "No sound cards" In armbian-config, I enabled analog-codec, `update-initramfs, rebooted, but there's still no sound card. mocp complains there is no driver. speaker-test (starts like this) Playback device is default Stream parameters are 48000Hz, S16_LE, 1 channels Using 16 octaves of pink noise ALSA lib conf…

Anyway, so here is another i can't log in my Orange Pi Zero, tried both images with Etcher, So where am i? It's a bit weird, i try various USB wall chargers and sd cards, but it always get to the same point: Permission denied, please try again. root@192.168.1.19's password: So let me ask you guys something, am i doing something Stupid, if i plug this into my modem, i can ssh to it yeah? there nothing i need to do? So i Nmaped it and sore that the vnc port is open, so password for that is 1234 as well? Like i went through the source, and i can see that the password is 1234, so the only thing that i can put it to is the setup of the sdcard but Etcher verifies th…

Greetings, I'm not good with linux so excuse any stupidity i might say. I have been using Xenial for years now and just decided to update. In the past i was using the sunxi module to access gpio's For ex: echo 1 > /sys/class/gpio_sw/PA7/data Now in Bionic i just noticed gpio's are not accessed in the same way. According to this user, we can either use sysFS (which seems deprecated) or libgpiod. The problem is that i can't make it work. libgpiod: root@orangepi:~# gpioset gpiochip0 29=1 gpioset: error setting the GPIO line values: Unknown error 517 sysFS: root@orangepi:~# echo "29" >/sys/class/gpio/export -bash: echo…

Hello, I'm having problems with USB sound card - speaker - card reader combo, named CD002 (hardware ID e2b0:0811). I managed to make it work with clean Armbian 5.38 image (kernel 4.14.14) by installing pulseaudio, but it sounds like crap using both mplayer and aplay; mplayer reports "audio device stuck" sometimes. The card is definitely OK, on RPi3 running DietPI it worked immediately and sounds fine. How do I set it up correctly so that it sound fine on OrangePi Zero & Armbian?

Hi, Many thanks for your support. I installed successfully the OpenMediaVault (OMV) ISO Image on the new Orange Pi Zero Plus (OPI0+): OMV_3_0_91_Orangepizeroplus_4.13.13.img.xz. I mounted an external USB 2.0 HDD. via OMV The OPI0+ is directly connected thru LAN cable to the router (Fritz!Box 7490). Login via PuTTY ssh works also fine. Additionally, I installed miniDLNA and configured folder/file sharing and media streaming. The flac-files are provided quickly, including album cover pictures (jpg). Now, I kindly ask for your support to disable Wi-Fi (WLAN). I thought about blacklisting the module 'cfg80211', but …