Allwinner sunxi

I have Orange Pi PC plus. When I install Jessie Desktop it doesn't start desktop and only runs command prompt. Tell me how to start Desktop

Hi all I have a banana pi running armbian. After the update to kernel 4.8.4 I am experiencing problems in enumerating USB device during boot (meaning device connected before powerup) I get errors like: [ 6.572517] usb 4-1: not running at top speed; connect to a high speed hub [ 6.578537] usb 4-1: unable to read config index 0 descriptor/start: -61 [ 6.578547] usb 4-1: can't read configurations, error -61 [ 6.789488] usb 4-1: new full-speed USB device number 4 using ohci-platform [ 6.848598] usb 4-1: not running at top speed; connect to a high speed hub [ 6.853598] usb 4-1: unable to read config index 0 descriptor/start: -61 [ 6.853620] usb 4-1:…

Is there a Xenial image for NanoPi M1, or a way to “easily†build one ?. I see here https://www.armbian.com/nanopi-neo/ that there is a Xenial image for NanoPi Neo. I am asking because I would like to run HQPlayer's Network Audio Adapter on my NanoPi M1. And this doesn't run on Debian Jessie legacy as it needs libstdc++6 (>=5.2), but it does run on a NanoPi Neo with Xenial. Any advice appreciated. Thanks

Hi! Can I install a clean Armbian from within Armbian, without flashing a SD-Card? One idea: After installing Armbian, I used the NAND-SATA-install to copy my files to a harddrive. But on the SD-card there is still the old system. Can I switch back to boot the SD-system? Wittenborg

Hi all, I am using NanoPi-Neo Air and my application is just logging binary data to a file. The board is powered by usb from a pc. I can dump and list to see binary data inside the file but after unplug power from usb then power up the board from usb again, I found the binary data is gone or some errors data, unknown data appended. Do you guys have same issued? or any suggestions? Thanks in advance

I just checked the mali blob: mali450r5p001rel0linux1fbdevarm64v8a (fbdev) and this blob is working on the legacy kernel with the proper patches. Nevertheless we may have some stability issues at the current voltage/frequence; Indeed gl-mark2-es-fb crashes around the refract test on my board.

I need to attach some devices via spi and i2c to an orange pi zero but would like to keep it in its original case. Just soldering a few wires to the gpio pins and drilling a hole in the case isn't really an option. I am looking for a nice and clean way. Browsing through AliExpress looking for connectors has not revealed any suitable options so far. I already thought about adding an 2.54mm 2x26 Pin Male Double Row Right Angle Pin Header and cut a suitable hole to the case but I guess it would protrude too much. Which connector do you recommend? It should have at least 4 contacts. Has anyone modified the case and added some small connectors? Photos? Lookin…

Hi all Does anyone recall if with kernel 4.9 it is required to put some patch for enabling power on the USB Host port of BananaPi? I am using vanilla kernel in another project, (LEDE) and when switching to kernel 4.9 I don't have any power from the USB port The dts is the vanilla one and AXP20x power driver is enabled Thanks!

Hello, First of all, please understand that I am a beginner level. My project is to make a NextcloudPlus on a Lime2 NAND version because of the following reasons : - Lime2 is Open source board, so no third party code into it - NAND version because I don't want to rely on a micro SD card, as it can be unstable for too many read/write (NextcloudPlus indexes a lot with sync). - SATA version because I would like to store data through a SATA HDD (I feel it is more stable than USB). So, I have tried to make : nand-sata-install ...but after shutting down and removing the micro SD cart, it was impossible to boot from NAND (the…

Took me over a year to isolate this bug. Randomly, I have found that /boot/armbianEnv.txt had unconsistent content. Examples: .tty1tty1LOGIN.8 ¹[fU7ttyS0tyS0LOGINusbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u network={ ssid="Demaine_40_Grd_Rue_Chambre-BP" #psk="1234567890" psk=693d195a3bf2ab6defbcc0b54604ced4286a067996138db6dc793d8648f67d79 } usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u network={ ssid="fabste" #psk="1234567890" psk=95342031a4b28398045e1761f9c64f8454902e80d37102e5476fa…

Hello Could You advice how to steering my GPIO output I need set "+" for this 4 canal 31 33 35 37 I already have the connect but can`t fine tutorial on web how to do it.

board in WIFI mode phy#0 Interface wlan-ap ifindex 3 wdev 0x1 addr 02:81:1d:98:1c:bc ssid tomesh-8583 type AP txpower 12.00 dBm Drivers seems to crash as soon as i try to associate the first device with it Any one know what could be causing it? hostapd.conf interface=wlan-ap hw_mode=g channel=11 auth_algs=1 wpa=2 wpa_key_mgmt=WPA-PSK wpa_pairwise=CCMP rsn_pairwise=CCMP ssid=tomesh-8583 wpa_passphrase=password123456 [ 40.084416] Unable to handle kernel paging request at virtual address e1f27e64 [ 40.091697] pgd = 1…

I use orange pi zero with armbian xenial 5.38 with update kernal via apt-get upgrade the issue is that sometime the device get hang at boot before the start of the kernal, and then we have to unplug it and plug it again i want to start watchdog at boot itselft, so if this happen the device reboot automatically i already sold 1000 devices, but now the sales stop due to this issue please help Thanks

Is it possible that there have been some image changes that broke the XR819 wifi completely? The available images for download on the Armbian page (5.3 server, and 5.4 minimal) as well as a custom built "legacy" branch linux-4.19 image all show the same behavior, The wlan0 interface is not active and it's not possible to bring it up. And dmesg shows that module has been initialized but not much more. Armbianmonitor support info: 5.3.9 official buster server image: http://ix.io/240Y 4.19.88 self-built, two days ago, legacy branch: http://ix.io/240U Everything below is from the official image, but the 4.19 image shows the exact same It is definitely not a h…

Hi, I have Orange Pi Zero v1.5 with Armbian Buster (mainline kernel 5.4.y) and I would like to use the serial_rs485 struct from user-level. It is possible?

Hi team, I am trying to get a voltage drop (3.3V to about 0V) detected on a GPIO pin on my OrangePi Zero running Armbian buster 20.02.1 with Linux 5.4.31-sunxi. I have another OrangePi Zero on which I have already managed to install I2C OLED screen, and the i2cdetect was working, and so on... For this one, I got a problem with the gpio group not existing. As I tried to install OPi.GPIO, I got usermod: group 'gpio' does not exist It's an Armbian version that I downloaded yesterday, and upgraded today with armbian-config. So... What did I do the wrong way? Thanks.

Hello Community, I'm trying to get Armbian running on my Banana PI M1 with the following image: https://dl.armbian.com/bananapi/archive/Armbian_20.05.2_Bananapi_buster_current_5.4.43_minimal.img.xz I flashed the image with Etcher on my SD Card which is a Sandisk Ultra 16GB SDHC Card. After flashing I have inserted the Card into my Banana PI but I only get a red light, I already tried different images like the bionic image but without positive result and tried different power supply cables. In my DHCP Server I see no request. I have also flashed for testing reasons current image of Bananian which was directly working but I don't want to use…

I cannot compile this module - https://github.com/uboborov/sunxi-cedar-mainline I get this: root@bananapim2zero:/usr/src/sunxi-cedar-mainline# make arch=ARM KERNEL_SOURCE=../linux-source-5.10.60-sunxi make -C ../linux-source-5.10.60-sunxi M=/usr/src/sunxi-cedar-mainline modules make[1]: Entering directory '/usr/src/linux-source-5.10.60-sunxi' MODPOST /usr/src/sunxi-cedar-mainline/Module.symvers ERROR: modpost: "arm_copy_to_user" [/usr/src/sunxi-cedar-mainline/cedar_ve.ko] undefined! ERROR: modpost: "arm_copy_from_user" [/usr/src/sunxi-cedar-mainline/cedar_ve.ko] undefined! ERROR: modpost: "kmem_cache_alloc_trace" [/usr/src/sunxi-cedar-mainline/ceda…

I tried to set the I2C interface with the armbian-config option but it doesn't work because it writes to the file: armbianEnv.txt .... overlays=sun50i-h6-i2c0 sun50i-h6-i2c1 sun50i-h6-i2c2 and it didn't work on my OrangePi3LTS and it doesn't start the i2C service on startup? but when I enter it manually: overlays=i2c0 i2c1 i2c2 then the i2c service works with my 40x2 LCD 🙂 ...is this a bug and if so can it be fixed? is the option: armbian-config still compatible with my OrangePi3 LTS?

Hi, How to build the Phoenix image from the Cubieboard2 NAND-flash? If anyone have idea I would appreciate. regards, Rassul.

Hi when i connect to the WUBR-508N to the UART conexion, the raspberry2 and the BPI-M2 turn off... i try to test other pines of Ground and Power but i have the same result... Its possible that the board WUBR comes bad?? or before i must to configure something on system?

Hi, I have tested this issue : https://github.com/linux-sunxi/linux-sunxi/issues/244 apparently it is not resolved. kernel panic log : [18109.785618] ------------[ cut here ]------------ [18109.790613] kernel BUG at arch/arm/mach-sun7i/dma/dma_core.c:32! [18109.795412] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM [18109.797259] Modules linked in: disp_ump mali_drm drm mali ump cpufreq_userspace ap6210 sunxi_ir hidp rfcomm hci_uart bluetooth sg [last unloaded: scsi_wait_scan] [18109.813725] CPU: 0 Tainted: G W (3.4.112-sun7i #2) [18109.816542] PC is at __dma_start+0x7c/0x80 [18109.819171] LR is at dma_ctrl+0x90/0x1dc [18109.828043] pc : [] lr : …

It has debian 8(jessie) server version 3.4.112-sun8i on it. It is updated to the latest version(apt-get update, upgrade). Caps Lock functionality works, but the light on the keyboard does not light up. I tried the keyboard on another computer, tried different keyboards. I am using this to get back the cursor. I found it here: http://forum.armbian.com/index.php/topic/1246-terminal-console-cursor-disappeared-after-apt-upgrade/ Could it have caused it? Anyone having the same issue?

Hi, after upgrading (and NOT following 'How to update) and reboot my cubietruck doesn't boot anymore. It's looking for a pxe-boot. Would anybody please be so kind and give me some help? Thanks, AxHa

Hello, I try to setup my Orange Pi Lite with a thermal printer (http://www.ebay.de/itm/122418910118?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT). With my Arduino the printer works perfect, so it is actually ok. I just can't figure out how to use the ttl connection. I installed pyA20 and try to implement a kind of SoftwareSerial and it didn't worked really well: #!/usr/bin/env python """Basic blinking led example. The led on A20-OLinuXino-MICRO blinks with rate of 1Hz like "heartbeat". """ import os import sys import time if not os.getegid() == 0: sys.exit('Script must be run as root') from time import sleep from pyA20.gp…

Hi, haven't touched my system for quite a long time, now I'm running into problems while trying to uprade system: Err http://apt.armbian.com trusty/main armhf Packages 404 Not Found ... W: Failed to fetch http://apt.armbian.com/dists/trusty/main/binary-armhf/Packages: 404 Not Found W: Failed to fetch http://nginx.org/packages/mainline/ubuntu/dists/trusty/nginx/binary-armhf/Packages: 404 Not Found [IP: 95.211.80.227 80] E: Some index files failed to download. They have been ignored, or old ones used instead. E: Couldn't rebuild package cache aptitude upgrade The following packages will be upgraded: linux-trusty-…

I was configuring onboard wifi of OPI ZERO, rev. 1.1 with the provided tool armbian-config. On one board it went just OK, on the second it froze, so I manualy powercycled the board. After that the board does not boot. I connected the serial console and here is the output I got: U-Boot SPL 2017.09-armbian (Nov 20 2017 - 02:53:16) DRAM: This is my first time troubling with u-boot, so I have no idea what this means, but it should give me more output. I will try to look, if there is 1.5V at the 1_5V pad.

Hello i have orange pi one, so i would like to connect my ipcamera into orangepi eth0 port and it should be accessable to internet over wlan0 my settings like this eth0 has static ip address 192.168.2.20 ipcamera has static ip address 192.168.2.200 wlan get ip from my home network router (dhcp) 192.168.2.210 my home router ip is 192.168.2.1 normally orangepi has internet access when ethernet cable unplugged, when i plug the ethernet cable i can reach ipcamera interface on browser by typing 192.168.2.200 but internet gone. also i've checked - Use this connection only for resources on its network - section at the …

Hi, I use orange pi pc plus with armbian bionic, firstly I use it with a SD card and the temperature its around 30 centigrade degrees, its ok. Then I use EMMC without SD card and the temperature increases to 51 degrees (I think it´s very high), they are some way to use EMMC without the board increases the temperature?? Best regards, Nelson

Hey. I'm trying to install octoprint on my Opi Zero +2, using the latest armbian image I found here on the site. Installation works fine, and I get the web interface up and running no problem. But I have connected power to the board on the gpio pins, and want to use the mini-usb to connect to the 3d printer. I have enabled usbhost0-3 in the hardware in armbian-config, but still it seems the printer cannot be reached. I read some older posts regarding other boards, where the solution seemed to be recompiling. Is this a necessity, and if so, could someone please point me to a walkthrough? Regards Anders

Hi , there I am trying to write a program which will detect the presence of SD Card in Nano Pi M1 plus device. There are many ways to do this either by doing fdisk -l or looking into /dev/mmcblk* . But I want to keep running it in a loop and doing fdisk -l and grep doesn't seems an appropriate way. Can the insertion or removal of SD cards be checked via Hardware Interrupts? Plz. help me I am a newbie. Thank in advance.

Hi, I would connect a 7" HDMI 1024x600 Touchscreen display (like waveshare or else) on Orange Pi 3 (as a raspberry). Latest armbian version for H6 CPU support this display ? If a need to use a 7" touchscreen display on Orange Pi 3 how can I do ? Thanks

Hi, who knows how to fix the problem of the displaced screen on the right? This is how Armbian appears with the latest build https://dl.armbian.com/orangepi3/nightly/Armbian_5.90.190705_Orangepi3_Ubuntu_bionic_dev_5.1.15.7z and this is how it appears to me with an old build with kernel 5.0.7, so it's not the monitor's fault Regards

Hi All! Is it possible to enable 1.8 Ghz on kernels 5.4.x (stable one) and 5.5-rc2 ? Thanks in advance!

I'm not familiar with the a64 graphics driver and some tty graphics software of mine is failing on Armbian Ubuntu Focal after working fine on the Bionic image. Earlier I was able to mmap() /dev/fb0 to display graphics in a tty. On Focal 20.04, running linux 5.4.43-sunxi64 , mmap() on /dev/fb0 is failing with EPERM (operation not permitted). Is this new error something anybody knows about or could give a link to find a possible driver change that's responsible? It seems there might be a few different video drivers on this system and I haven't looked at them before. /sys/class/graphics/fb0/name contains sun4i-drmdrmfb /sys/class/gr…

Hello, I am making a board coupled to a NanoPi Neo Core, and a RS485 converter to its UART2. The chip is a MAX1478 and I use the RTS (PA2). this is my armbianEnv verbosity=1 bootlogo=false disp_mode=1920x1080p60 overlay_prefix=sun8i-h3 overlays=cpu-clock-1.2GHz-1.3v i2c0 i2c1 uart1 uart2 usbhost0 usbhost1 usbhost2 rootdev=UUID=a37457d6-57d2-4f17-a684-157b1a309a73 rootfstype=ext4 user_overlays=neo-core-stable-mac double-spi ds1307 param_uart2_rtscts=1 param_uart3_rtscts=1 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u if i run the command, cat /proc/tty/driver/serial |head -8 uart:16550A mmio:0x01C28800 irq:53 tx:120 rx:0 RTS|DT…

Hello, I am trying to communicate using UART PORT. I have connected to 8, 10 and GND pin. Also I enabled UART3, but it doesn't work. Any solution? Thanks !! Enviado desde mi iPhone utilizando Tapatalk

Hi everyone, I am experiencing a persistent boot issue with my Orange Pi Win Plus running Armbian, used as a headless server. The Problem: Whenever the board suffers a power loss (unplugged) or I issue a system reboot, it fails to start automatically. The power LED stays on, but the system/network never comes up. To get it to boot, I have to go through a frustrating manual routine: manually holding/pressing the power button, sometimes plugging/unplugging the HDMI cable, and repeating this process a couple of times before it finally kicks in. What I have already checked/ruled out: Power supply is NOT the issue: I have tested multiple different power ada…

Hello. My friend and I are comparing performance results with our cubietruck's. I'm using Armbian (Trusty vanilla latest update) and he's using ArmArchLinux. We tested a few dozen phoronix-test-suite tests and most results are the same except one. We both have a fresh OS install with no extras installed. The problem is with the phoronix-test-suite ramspeed integer copy test, I'm getting 812.03MB/s but he's getting 1479.73MB/s. Other ramspeed tests are giving proportionally equal results. What can explain such difference? Is my RAM running slower?

I tried all 3 versions but they doesn't boot. I tested using Armbian 4.5. It booted correctly. I used Rufus for writing to SD. Is there anything changed for writing? Also does it support LeMaker official lcd at version 5.1? Thanks.

Hey there, I have managed to compile your great image. How ever I dont receive any HDMI signal on boot. During the first boot I got atleast some picture. but after loading kernel all went black. See log: https://sprunge.us/YjQd I used a] HDMI to VGA converter b] a direct HDMI connection. Both screens usually work. See log: https://sprunge.us/YjQd I will continue to install the system via SSH, however I would like to use HDMI lateron e.g. in emergency cases. Greetings!

I have a fresh install of Armbian 5.14 on a orange pi one. I i have updated and upgraded it. I have only installed synaptic and nautilus. I then followed the instruction to install the micro home server and I commenced to install the Samba option. It ran and then once it had finished said something like samba not running or samba not configured. I tried to browse the network and look for my Tplink NAS router and it says "this location could not be displayed." I would appreciate any ideas to get samba running.

Hi! I thought, I might save some energy by using a Sinovoip Banana Pi M2+EDU (it is like the M2+ but no WiFi and no display (EDIT: I mean 8 GB EMMC) and 512MiB DRAM) instead of an Atom N270. Here at armbian.com/download I only found "legacy" 3.4 images, which work nicely... I wonder, if it is a good idea to stick somelhing into public internet with a 3.4 kernel... So I tried to install lhe latest archlinuxarm kernel tar ball with a git clone of u-boot (using Sinovoip_BPI_M2_plus_defconfig) and it boots nicely, but: 1. There is no eth0 (so it is much safer from the public inet, than I like) and 2. there is no cpufreq (so it gets quite warm and i can't eve…

Hi guys! I've an Olimex LIME2 EMMC installed in a remote location: I installed it with Olimex provided image of debian Jessie, which has kernel 3.4.103-00033-g9a1cd03-dirty. The installation has been done over internal EMMC and it worked. Now, for various reason I would like to switch to armbian. I would like to install armbian over the existing image. so not to have to reinstall packages ad my local software. I would like to keep the installation on internal 4GB EMMC memory. I'm asking if it's possibile to do it without having to reinstall and possibily over ssh, because the board is in remote location. Thanks for your sug…

Hi, I am trying to create some kind of audio streaming server on orange pi zero. I've installed Qt5 and tried to start streaming audio using UDP datagrams. The problem is that sending one datagram takes a lot of time(~50-100ms) so there are interrupts in audio streaming. What is more I found out writing datagram gives me this message in dmesg: Loading kernel module for a network device with CAP_SYS_MODULE (deprecated). Use CAP_NET_ADMIN and alias netdev- instead. I am using Xenial with Linux orangepizero 3.4.113-sun8i #10 SMP PREEMPT Thu Feb 23 19:55:00 CET 2017 armv7l GNU/Linux That is my lsmod output: usbt…

i downloaded the desktop for opi one and on first boot it wants me to change password but gives error msg and doesnt take new password

hey guys I ran some test with both version of OPI Win's Armbian and: I got all time reboot on server edition I see the the first Armbian boot up page but desktop wouldn't show up... please give me solutions. Thank you guys.

I've a opi zero running the latest armbian stable release, it just handle a pihole dhcp server and run the transmission client, but randomly stuck becoming inaccessible through ssh and webserver pages. All return normal when it restart by manual removing the power supply, but this way it's very uncomfortable, so what could be the cause? Is there a way to log the system errors for read them the next reboot? Thanks

Good night, I have the sound problem but with hdmi audio, de default is the 3.5 mm audio jack, then I looked for the asound.conf in /etc, then I found that this file doesn't exist and after that I've created it with the following content: pcm.!default { type hw card 1 device 0 } ctl.!default { type hw card 1 } the problem is that even created this way the sound output still being the 3.5 mm jack and I don't know if I need to change some setting to mpv player to output the sound through hdmi. What else can I do to change the sound from audio jack to hdmi?

This seems like a really simple problem, but I can't find any pointers on any forums. I am running a NanoPiNEO2 (Allwinner H5) using the latest Armbian build DISTRIB_ID=Ubuntu DISTRIB_RELEASE=16.04 DISTRIB_CODENAME=xenial DISTRIB_DESCRIPTION="Ubuntu 16.04.3 LTS" I am trying all ways to save power. For most of the time, I do not need to use the Ethernet interface (I am using the USB interfaces for comms). I have tried all the obvious commands such as ifdown, and explored ethtool, but nothing I do makes any difference to the current consumption of the device. I expect i am missing something obvious - any help gratefully accepted.

So trying to run some GPIO interrupts using wiringpi. Using the wiringPiISR function and setting and interrupt handler seems to work, but as soon as the first interrupt happens, the handler gets stuck in some sort of loop and just get infinitely called. Pretty sure this is some bug in sys, since the wiringPiISR function just uses sys gpio calls to do the interrupts. Could be wrong and just be an issue with how wiringPi does it. Either way has anyone come across this and know of a workaround to fix this?

In the last weeks I've successfully installed Armbian Debian Stretch 5.59 onto a Banana Pi M2 Berry, now I'm trying with a Banana Pi M1. From https://www.armbian.com/bananapi/ I've downloaded the Debian Stretch image and wrote it to my 4GB SD-card using Etcher (on Windows 10) - Etcher meant it was successfully after writing. I've safely ejected the SD-card from Windows, plugged it into the Banana Pi M, but it tries to boot from the network. Then I've taken a look at https://dl.armbian.com/bananapi/archive/ and downloaded Armbian-5.59 Debian Stretch image, wrote it with Etcher again, booted. Same issue. It shows a red armbian logo with "initializing boot loader…

Can anyone confirm the Orange Pi Zero Plus H5 boards have been discontinued. The boards are no longer sold here: https://www.aliexpress.com/item/32828347476.html

Hi all, First of all sorry if i posted in the wrong directory I'm currently facing some issues with my orange pi one and in particular with node red and my dht22 temperature and humidity sensor i installed the stable buster version on my sd card this works perfectly and after that i installed node-red on it. in node red I installed the dht sensor pallet and added it to my flow but here is were the issues are starting, i need to select which pin it is connected to and what gpio i use. i can only select bcm gpio, rev1, rev2 or wiringpi 1 or 2 and then which pin it is connected to. i have the sensor connected t…

This topic has been discussed earlier but there is not concrete mechanism explained to achieve this. Ideally I would like to display a boot logo or boot splash during startup. The device is Orange Pi Plus 2e. As per experience and as mentioned on this forum earlier plymouth was not useful in this case. I tried to set logo="enabled" in /boot/armbianEnv.txt but this doesn't help. When Armbian loads for first time on the device from the image downloaded from this site, it displays 'Initializing Boot Loader' logo image. Pretty cool!!! Can we have something like this for a custom image displayed each time on reboot. I under…

Hello, friends. I am using legacy Armbian 3.x kernel on my development boards where I run Stella emulator with some special USB joystick. The joystick is detected as XBOX controller, hence I guess it uses xpad driver. The problem is that this driver is not present in the latest Armbian so this joystick does not work. I would like to use latest Armbian to have the latest packages, using it as a print/scan/radio server and would like also to play some Atari game from time to time. I tried to build it from the source using this https://github.com/paroj/xpad I can load it with modprobe, the joystick seems to be detected, but it is not working in Stella, I cannot eve…

So I got a new orange pi 3 lts and I have installed armbian bullseye on it, but I can't seem to make it work with my crt TV like my raspberry pi 3 b+, even though I am using the same cable and TV and it still works with my raspberry pi I have tried: -Changing the resolution -Changing the aspect ration But nothing works What am I supposed to do to make my armbian work on my CRT tv??

I have a question for more experienced users. Quite a long time ago I built an internet radio based on OrangePi Lite + DAC I think in the I2S interface with the module: PCM5102 ... PCM5102 DAC Decoder I2S -Aliexpress unfortunately the board broke down. I have another model, the aforementioned Pi 3 lts but it seems to be less supported. Can I connect the above-mentioned PCM5102 module to this model? Or maybe buy some other supported model that will work just as well as Pi lite with this DAC model or another? Ps. it would be nice if it had the ability to upload Armbian firmware to emmc flash memory I installed Armbian/Ubuntu on Pi3lts but I get some erro…

Hi, I have managed to install u-boot on the spl flash, and it properly runs and detects everything, but i've run into a bit of an issue, while loading the kernel, it gets stuck. To create the usb drive I just cloned the partition of the sd card (not the whole card, just the ext4 partition), I don't know if that can be the issue. here is the full log: https://pastebin.com/jPEkMnYq Any ideas?

Hello, I am trying to run Armbian on my Orange Pi 3 LTS. The official Orange Pi image works normally: Orangepi3-lts_3.0.8_debian_bullseye_server_linux5.16.17 However, when I flash the Armbian image: Armbian 26.2.1 Minimal / IoT I get several boot errors during startup: [FAILED] Failed to start Apply Kernel Variables. [FAILED] Failed to start Dispatcher daemon for systemd-networkd. [FAILED] Failed to start Helper to synchronize boot up for ifupdown. [DEPEND] Dependency failed for Raise network interfaces. The system continues booting, but these errors appear every time. Hardware: Board: Orange Pi 3 LTS Image: Armbian 26.2.1 Minimal /…

I want to write microSD card as less as possible and CUPS package uses the following path's by default (although can be changed): /var/cache/cups /var/log/cups /var/run/cups /var/run/cups/printcap /var/spool/cups /var/spool/cups/tmp But I think this paths are pointing to micro SD card (except .'/var/log') (or not?) root@pcduino3nano:/etc/cups# df -h Filesystem Size Used Avail Use% Mounted on /dev/root 7.3G 1.1G 6.0G 16% / devtmpfs 500M 0 500M 0% /dev tmpfs 128M 212K 128M 1% /run tmpfs 5.0M 0 5.0M 0% /run/lock tmpfs 128M 0 128M 0% /run/shm tmpfs 256M 0 256M 0% /tmp ramlog-tmpfs 256M 2.2M 254M 1% /var/log Which is the best strategy so this path's points to memory and N…

Hi guys, I am very sorry to bother you, I tried everything I could to make this work but unfortunately, I can't figure it out. So here I am asking for help ! I am using the Armbian 4.5 Jessie (Kernel 3.4.109) on an Olimex Lime A10 board, everything works fine (Wifi & Bluetooth via USB dongles), but there's no sound. I tried aplay -l but nothing is found. modprobe sun4i_codec returns "codec not found". Could you help me find what's wrong ? I would like to avoid compiling a kernel by myself if it's possible ... Thanks !

For some days now I have the board mentioned in the subject, the goal is to have a webserver, git server, and maybe lateron something like a mini-personal-cloud for my family. Yesterday me and my brother finally decided which OS to use - and dd-ed the SD card with the Armbian/Debian Vanilla Jessie Server image (Armbian_5.10_Lime2_Debian_jessie_4.5.2). Some hours later after installing apache2 and trying things out I thought it would be a good idea to do an apt-get upgrade for security reasons before exposing the server to "the world". Unfortunately it was not: The device is not booting any longer after the upgrade. This is the log output of /var/log/apt/term.log (I moun…

I have tested with two SDs - the same result. But vanilla works perfect! Strange is that after dd command I can't mount SDs with legacy, but vanilla I can. I've downloaded legacy twice.

Hi, I have recently upgraded Armbian as suggested with: apt-get update apt-get upgrade apt-get install -f apt-get upgrade apt-get autoremove -y After that i2c-0 stopped working: Output if i2cdetect -y 0 before upgrade: 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 70: -- -- -- -- --…

Hi all! I have browsing the forum quite while but I did not a solution for my problem. I have bought the OP Zero from DX.com and it came with an expansion board which has two additional USB ports, a 3.5 mm AV socket and a built in microphone. And now I would like to use the audio socket as audio output and I want to use its microphone as well. But I headed some problems and I cannot use its audio features . I am using this kernel: Armbian_5.24_Orangepizero_Ubuntu_xenial_dev_4.9.4 I think there is no audio driver installed on this system. here are some other debug info: aplay: device_list:268: no soundcards found... arecord: device_list:268: no soundc…

Hi all, I've installed the latest jessie Mainline 4.9.7 on a cubietruck and when I give sudo hwclock I get no printout and if I run hwclock as root I get segmentation fault Does anyone has an idea what is wrong ?

Hy, i find one big problem. Can't add new connection type in network manager. Edit box is inactive,gray... Not work network manager on orange pi pc and plus2e Idea?

Nano Pi Neo, Armbian (Armbian_5.27.170422_Nanopineo_Ubuntu_xenial_dev_4.10.11) External USB device works fine when connected via USB-A jack, but doesn't work when connected to 2.54 pin header (2,3). Is there some additional steps to activate internal (usb1, usb2) ports, or it's hardware problem?

Good evening, I'm using a NanoPi Neo Air for streaming audio via bluetooth to a I2S sink. It's working in general but the audio data breaks away every second. It's always a on/off. I'm pretty sure it's connected to the speed between H3 - AP6212a but I'm not able to get it to work propably. I set the UART ttyS3 speed to 1500000 bit/s: My Fexedit looks like that: [bt_para] │ │bt_used = 1 │ │bt_uart_id = 3 │ │bt_uart_baud = 1500000 │ …

Hi Guys, I bought one of these pcDuino 4 (Nano Pi M1) boards: http://www.linksprite.com/pcduino4-nano/ Works great with Armbian Legacy Kernal. I got this screen with the HDMI + DSI Driver Board. Works fine with normal PC -> HDMI output but will not work with the Nano Pi.. https://www.alibaba.com/product-detail/LS055R1SX04-1440x2560-5-5-2K-LCD_60672828148.html?spm=a2700.7724838.2017115.1.3c93b095HGc0XS The LCD screen just turns on then off and on and off forever. It never locks on to the HDMI signal. The Nano Pi M1 works just fine with a regular monitor but not with the LCD/Driver combo. I have seen some purple images come up on …

Hello guys, I am having problems with vlc, the video is running out of proportion and it is all over the interface, ie, even minimizing vlc the video is still being shown, I tried to change the codecs but I did not have a satisfactory result, because only the VDPAU works without lags Help me please, sorry for bad English.

Hi, I've been playing around with a OPi Win+ which is aint bad but full support seems a while off ... I'm looking for a quad core, 2G, good wifi with external antenna and this seems to fit the requirements. I dont care too much about hdmi but if it works all the better. I was just wondering what current owners thought of it. Can the internal wifi do AP mode and will it do dual modes ... hostapd-8188 will create wlan0 & wlan1 so that you both connect to an AP and be an AP. Google doesnt show much about 8189ETV Given that the armbian download shows it with a legacy kernel but stable I expect that everything 'works' ... …

Hi! How to install postgresql-10 in ARMBIAN 5.36 (BananaPi)?

Hello, I've been trying to interface Kedei hdmi 3.5 inch hdmi lcd (480x320) with orangepi one. So far i"ve been unable to display anything on lcd using Armbian mainline kernal image. But with legacy kernal using h3disp command i was able to change the resolution but the lcd than gave message " Not Supported". Can someone please help me how to do this?

I'am running a PiOne with 4.14.14 Stretch. I have installed acpid and give the command acpi_listen When pussing the button in Stretch and I didn't see any logging. With the old kernel in 5.38 Jessie on the same PiOne I saw button/power PBTN 00000080 00000000 button/power PBTN 00000080 00000000 button/power PBTN 00000080 00000000 In the output of dtc /boot/dtb/sun8i-h3-orangepi-one.dtb I saw key_pins@0 { pins = "PL3"; function = "gpio_in"; linux,phandle = <0x39>; phandle = <0x39>; }; Means gpio_in defined as an input? Is the button function not yet implemented in 4.14.14? Or is something going wrong?

Libre software refers to the free software foundation's guidelines. Can you make an entirely libre software armbian version work on the orange pi one or other orange pi computers? How good will it work? About the orange pi one which devices will not work if only libre armbian software is installed? Notice this https://www.kickstarter.com/projects/bootlin/allwinner-vpu-support-in-the-official-linux-kernel/description If orange pi computers can work using libre software armbian, then how do they boot? Do they use uboot? Thanks.

Good day, I use prebuild Armbian Stretch mainline kernel 4.14.y. And I want to connect pcf8563 rtc through i2c protocol on TWI1_SCK/PB18, TWI1_SDA/PB19 hw A20 pins. pcf8563 slave address is 0x51. If by default, no i2c are enabled through overlays= in armbianEnv.txt, I still get i2c-1 device with addresses 0x51-0x57 occupied: root@lime2:~# ls /dev | grep i2c i2c-0 i2c-1 root@lime2:~# i2cdetect -y 0 0 1 2 3 4 5 6 7 8 9 a b c d e f 30: -- -- -- -- UU -- -- -- -- -- -- -- -- -- -- -- root@lime2:~# i2cdetect -y 1 0 1 2 3 4 5 6 7 8 9 a b c d e f 50: UU UU UU UU UU UU UU UU -- -- -- -- -- -- -- -- If I enable i2c1 through over…

considering to buy orange pi 3 with new H6 cpu, usb3.0 port and onboard emmc, but everyone has been complaining official images, just wondering if orange pi 3 will be supported soon.

today I compiled a image for my OPi One: Armbian Buster with Linux 5.4.2-sunxi package bsp-kernel[19.11.3.342] u-boot[19.11.3] dtb[19.11.3.342] firmware[19.11.3] config[19.11.3] branch[dev] but mpg123 is playing a 128kb/s Radio-Stream much too fast via HDMI (hw:0,0) - streaming the same URL via a USB-Audio-Dongle (hw:1,0) has the right speed Spoiler root@opi-one(192.168.6.114):/toshiba/iradio/stations# more ./MP3_SAW_80s http://saw-de-hz-fal-stream10-cluster01.radiohost.de/saw-80er_128 root@opi-one(192.168.6.114):/toshiba/iradio/stations# mpg123 -v -b 2048 -a hw:1,0 -@ ./MP3_SAW_80s High Performance …

Environment: (H2+) + linux-sunxi + ov5640 It can be registered by kernel ,but I can't capture any picture from camera . Here is my kernel demsg: ===================================================================================== # dmesg |grep VFE [ 1.720292] [VFE]cci probe start cci_sel = 0! [ 1.720328] [VFE]cci probe end cci_sel = 0! [ 1.720359] [VFE]cci_init end [ 1.720372] [VFE]Welcome to Video Front End driver [ 1.720514] [VFE_DEBUG]vfe_probe [ 1.720638] [VFE]pdev->id = 0 [ 1.720644] [VFE]dev->mipi_sel = 0 [ 1.720650] [VFE]dev->vip_sel = 0 [ 1.720655] [VFE]dev->isp_sel = 0 …

Short issue description: sometimes after pulling a USB device out it makes OPi3 USB host controller stuck. One or more USB ports are getting unresponsive (sometimes all four of them) and no messages in dmesg about connection/disconnection. No matter what device is used. This thing happens only on the first host controller, the second rear one is functioning and responsive. It happens more often if we push in and pull out four devices in a short period of time. Wherein /sys/kernel/debug/usb/devices is stuck too, we cannot read the info from it and all the utils (vi, cat, etc.) are getting the D state (uninterruptible sleep). "lsusb" is also not working, but can b…

Hi, my Armbian Reports as 23.02.2 with Kernel 5.15.93. According to website there is already 23.5 with Kernel 6.x. How can I upgrade my existing installation? I tried apt update dist-upgrade and the "Update all packages and firmware" option in armbian-config. best regards thommy

Hello, I'm using a BananaPi and just tried the latest version (10.6.2015, Linux 4.0.5) of your great distribution. Unfortunately, support for ath9k_htc based USB Wifi adapters seems to be missing, which is crucial for me. (ath9k_htc works great using free and open source firmware.) Could you please add support for this kind of hardware for future releases or give me a hint how I could add support to your existing images? Thank you and kind regards, LINMOB

Scenario 1:[router]<--(ethernet)-->[pcDuino3] pcDuino3 IP: 192.168.1.5 root@pcduino3nano:~# dpkg-reconfigure tzdata Current default time zone: 'America/Bogota' Local time is now: Wed Dec 31 20:48:49 COT 1969. Universal Time is now: Thu Jan 1 01:48:49 UTC 1970. root@pcduino3nano:~# date Wed Dec 31 20:49:01 COT 1969 root@pcduino3nano:~# ntpq -p remote refid st t when poll reach delay offset jitter ============================================================================== yak.osoal.org.n .INIT. 16 u - 64 0 0.000 0.000 0.000 bunny.zeroloop. .INIT. 16 u - 64 0 0.000 0.000 0.…

Hi, I just joined up so I'm an extreme newbie here. I'm running the legacy trusty version of Armbian just downloaded. The HDMI display and USB ports are working fine. The Cubieboard2 is showing up in the network. I need to get the SPI interface going to talk to a microcontroller -- an STM32F303. I've enabled the particular SPI port I need in the cubieboard2.fex file (derived from the stock cubieboard2.bin file) and created the cubieboard2.bin file in /boot/bin after backing up the original. After that change, I rebooted. I got the /dev/spidev0.0 to show up. What do the parameters in the spi_board section mean? Is that documented somewhere? Thanks, Chri…

Maybe this is not strictly related to Orange Pi PC but a few weeks ago I had problems with booting my device - mainly OpenELEC and I had to debug it somehow using serial port and the terminal. Unfortunately my PC is rather far from the place where I keep OPiPC. So I was forced to prepare separate device - cheap STM32 MCU based terminal display with 2.2" LCD screen directly supplied from Orange Pi PC 3.3V. It can be used also with other devices which allow serial console debugging. Watch below videos for more details and the code: Maybe someone finds it useful.

Hi all. I recently bought an Orange Pi Lite. After trying to get the power switch to work as a power switch (by this I mean booting the board when it was previously shutdown), and after searching for a while, it seems that the power switch in the Orange Pi Lite is not a real one, but it's instead connected to a GPIO. Do you guys know of any Orange Pi board that implements a proper power switch? Thanks.

Hello! Can anyone help me to set up my Orange Pi one ,that I could use gpio's with node-red? I am using armbian 5.22. Recently I am trying to manage my OPi One to work with Node-Red. Today I finally set it up and was able to start Node-red. After that I tried several hours to manage GPIOs ,but nothing worked. Is there a short version how to manage gpios to get them working. So today I installed nodejs 4.xx, npm@2.x. After that I installed wiringPi from github, then I added to node-red -> npm wiring-Pi and modified settings.js , after that I tried npm -> wiring-op and still nothing. I my experimentations today I started 3 times with cleans jessie install…

This was my second attempt and it finished with exactly the same result. Console log: ~$ ssh admin@zero ___ ____ _ _____ / _ \ _ __ __ _ _ __ __ _ ___ | _ \(_) |__ /___ _ __ ___ | | | | '__/ _` | '_ \ / _` |/ _ \ | |_) | | / // _ \ '__/ _ \ | |_| | | | (_| | | | | (_| | __/ | __/| | / /| __/ | | (_) | \___/|_| \__,_|_| |_|\__, |\___| |_| |_| /____\___|_| \___/ |___/ Welcome to ARMBIAN Debian GNU/Linux 8 (jessie) 3.4.113-sun8i System load: 0.07 Up time: 3 min Memory usage: 9 % of 494Mb IP: 192.168.8.9…

Hi, I did read a lot about temperature and power consumption on this forum. Most is about bad parameters for the Orange Pi H3 boards. I use armbian 5.25 stable with 3.4.113-sun7i kernel. On both i run this same version, the only difference is that i use an other script.bin on the orangepi. The script.bin who is in the distrubution. I dont use a heatsink on both. I noticed the following On the Orange Pi: Load1 is max 0.50 with 2 values of 1.00, avg 0.20-0.25 Load15 is between 0.08 and 0.14 The temperature is between 49 degrees and 52 degrees Celcius The PMU current is between 400 and 800 mA PMU Consu…

Hello guys, I've been trying for the past month to get USB OTG and I2C to work on a NanoPI NEO AIR running Armbian, without any success. For OTG what I've tried was adding the following to "sun8i-h3-nanopi-neo-air.dts": &usb_otg { dr_mode = "otg"; status = "okay"; }; I have also enabled OTG and I2C in the kernel config menu, but for I2C I couldn't find what to put inside the DTS file. Can someone give me pointers on how to solve this, please? Yes, I am a very inexperienced developer when it comes to embedded systems and have very poor understanding of how to properly configure a device tree source file. Any help wo…

I used the Armbian test image. I did apt-get upgrade I changed eth0 to static IP. But now, I started it up and eth0 green light won't stay on. Can't ping it or SSH. I connected a USB PL-2303HX from my PC to the NanoPi Neo2 (first time for me ever connecting to a Linux computer's serial console) With no configuration at all I got this output in minicom. U-Boot SPL 2017.09-armbian (Sep 17 2017 - 03:48:48) DRAM: 4096 MiB Trying to boot from MMC1 …

Hi, I am having doubts on how to use I2C ADS1115 unit on Orange Pi Lite. I already have I2C module and tools installed (see below). Thing is, where do I get the Phyton library to make use of it? Are there any examples? The other question is about wiring. When I connect to twi0 I cannot see the I2C device: root@orangepilite:~# i2cdetect -y twi0 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- --…

Today i compiled for my Orange Pi One the kernel 4.11.12-sun8i from the sources. The kernel works with only 1 (one) core. / _ \ _ __ __ _ _ __ __ _ ___ | _ \(_) / _ \ _ __ ___ | | | | '__/ _` | '_ \ / _` |/ _ \ | |_) | | | | | | '_ \ / _ \ | |_| | | | (_| | | | | (_| | __/ | __/| | | |_| | | | | __/ \___/|_| \__,_|_| |_|\__, |\___| |_| |_| \___/|_| |_|\___| |___/ Welcome to ARMBIAN 5.31 stable Debian GNU/Linux 8 (jessie) 4.11.12-sun8i System load: 1.11 0.26 0.09 Up time: 0 min Memory usage: 10 % of 464MB IP: 192.168.3.156 CPU temp: 43°C Usage of /…

kernel: "Linux orangepizero 4.13.16-sunxi #20 SMP Fri Nov 24 19:50:07 CET 2017 armv7l armv7l armv7l GNU/Linux". I have tried this document, http://opi-gpio.readthedocs.io/en/latest/api-documentation.html#pull-up-pull-down-resistors I am using pin 7 (GPIO 6) and INPUT mode, but it not working, however I got push signal, but I have not push it, why? The following is my python code. import OPi.GPIO as GPIO import time channel = 7 GPIO.setmode(GPIO.BOARD) GPIO.setup(7, GPIO.IN) while True: time.sleep(0.5) print GPIO.input(channel)

Hi, I get this line on my welcome screen of my Orange Pi Zero: Welcome to ARMBIAN 5.38 stable Ubuntu 16.04.4 LTS 3.4.113-sun8i When I checked the download page, I see this as the file name: Armbian_5.38_Orangepizero_Debian_stretch_next_4.14.14 I got confused about the numbers 3.4.113 and 4.14.14 What do they mean? Is my installation behind the latest version? Can I upgrade to it?

I'm trying to configure the RTL8189FTV module on an Orange Pi+ 2E in SoftAP + STA mode so I can use it as wifi hotspot. According to this old document from Realtek (http://www.ofeixin.com/downloadRepository/8da8dda7-6721-4ac8-a7db-47cc4d9b218c.pdf), it's possible to do so using an RTL8189ETV, so I'm assuming it's possible on the RTL8189FTV, too. The default driver doesn't allow concurrent connections like this, tho, so it must be recompiled. I downloaded the source recommended on the sunxi wiki (http://linux-sunxi.org/Wifi#RTL8189FTV): git clone https://github.com/jwrdegoede/rtl8189ES_linux.git cd rtl8189ES_linux git checkout -B rtl8189fs origin/rtl8189f…

I will describe my problem with NanoPi Neo Core2: I installed the system on eMMc I installed WiringNP I installed the USB drive Everything worked, also Putty via USB I wanted to connect the external module via SPI. The module requires setting the transfer frequency to 20 MHz. I decided to look at the file sun50i-h5-nanopi-neo-core2.dtb . For this purpose, I decompiled to a file . dts . Due to late night time I made a cardinal error, that is before these activities I did not copy the file . dtb I just played on the operating system. After the power is turned off NanoPi and the next day the system is not raised. Red power LED is lit green while…

Hi, I'm new to the Armbian/Alt PI scene, coming from a RPI Zero W. I'm needing to interact with my PI using a CH340G (is it compatible) USB to TTL dongle. I've also trjed a CH351A device, put it into UART mode. Unfortunately, I get nothing from the PI. Despite using the primary RX/TX pins. I've also tried enabling all of the UART pins using armbian-config, and using another set of pins - to no avail. Please view my setup below. I've run out of ideas of where I'm going wrong. I've tried these images: Armbian_5.90_Nanopineo2_Debian_buster_next_4.19.57 Armbian_5.90_Orangepione_Ubuntu_bionic_next_4.19.57 Refer…