Allwinner sunxi

Hi, I have an Orange Pi Plus 2e and I've installed Armbian_5.59_Orangepiplus2e_Ubuntu_xenial_default_3.4.113_desktop. I need to play four hd videos at the same time. I could do it with Raspberry pi3 model B with 720M GPU memory. I played videos with MPV with X11 but couldn't play with VPDAU. It is just played only one video. What can I do? Can I set GPU memory? Thank you.

Hi, Since recent I have an issue that my Orangepi doesn't start anymore. My microSD is fine (did a full diskcheck using badblocks on ubuntu), en I can access all the files without issues. However, it doesn't want to boot. Every time I try to boot it (Orangepi pc), it gives the first black screen until starting kernel, and then gets stuck on the blinking underscore. For information: I have an Orangepi PC and Armbian 5.32 with mainline kernel. Now, this happened after I did an apt-get upgrade (incl. kernel upgrade) from 5.30 to 5.32, and then didn't reboot, but my orangepi had a short power interruption. After this it didn't want to start…

Hi, on my BananaPI I installed this image: Armbian_5.10_Bananapipro_Debian_jessie_4.5.2_desktop.raw I followed these instructions: https://searchathing.com/?p=250 to move / to SATA (or USB) and crypt it with LUKS. After all, cat /proc/cpuinfo says, there is only 1 CPU-core. How can I activate the 2nd core? Thanks for your help

Hi All, Just wanted to share a good story using armbian. I have used in the past 1-wire probes for temperature, and the process included decompiling, editing and recompiling dtb for my Banana Pi M1, which was not easy at all. Every firmware update deleted by changes and had to redo de recompilation. With latest kernels and armbian version, the process is now extremely easy, just edit: /boot/armbianEnv.txt Adding this lines: overlays=w1-gpio param_w1_pin=PI3 # desired pin(7th pin (GCLK) or number 4 on first column where number 1 is +3V) param_w1_pin_int_pullup=1 # internal pullup-resistor: 1=on, 0=off …

Hi, I run a Linux Armbian_5.24_Cubietruck_Debian_jessie_4.8.15 on a Cubietruck with the kernel on version 4.8.15-sunxi. When i want to enable the wifi module, this don't work. I have see a response on https://forum.armbian.com/index.php/topic/252-cubietrack-wifi-bug-hostapd-bcmdhd/ so i do "modprobe brcmfmac" which return any message. But after that, i can't use the wifi. When i do an ifconfig, i see only eth0, bond0 an lo butno wlan0. Can you help me to use the wifi on my cubietruck ? PS : Sorry for that bad english, i'm a french user which don't speak english very well.

Hi trying to install Debian on my allwinner a20 board and been running into issues used this link http://mirror.igorpecovnik.com/Cubieboard2_Debian_3.8_jessie_3.4.107.zip the imagewriter doesnt really work for windows 8 keep on crashing and doesnt find the sd card so i used win32imager to write the raw file to the card checked so wrote the filesystem to the card the popped it into my Cubieboard and it detects that there is a sd card and then it messes up took a pic with my camera seems that it tries to tftp boot https://www.dropbox.com/s/nhzir29jyw4bjhf/IMG_20150526_162455.jpg?dl=0

My PineH64, as well as OrangePI one plus (H6) were working fine using 4.18.rc7-bionic till I have tried apt upgrade I'm getting the following error on both. Any ideas? Thank you vm Starting kernel ... [ 2.104055] Internal error: Oops: 96000004 [#1] SMP [ 2.108938] Modules linked in: [ 2.111997] CPU: 1 PID: 33 Comm: kworker/1:1 Not tainted 4.19.11-sunxi64 #5.67.181221 [ 2.119819] Hardware name: Pine H64 (DT) [ 2.123750] Workqueue: events deferred_probe_work_func [ 2.128887] pstate: 80000005 (Nzcv daif -PAN -UAO) [ 2.133679] pc : sun8i_dwmac_probe+0x16c/0x550 [ 2.138121] lr : sun8i_dwmac_probe+0x21c/0x550 [ 2.142560] s…

Hi, I have OPi One Plus (H6) and I didn't find a way to access/control the GPIO's and the UART in the 26Pin connector. Is there a drivers release or a way to do it. thanks, Yohay

Just "ln -sf interfaces.r1router interfaces" ? Should I install a dchp server?

Hello, first post here, so sorry if did not provide enough information. I need to change spi buffer length to 8192. So far tried: 1) modprobe spidev bufsiz=8192 creating the file /etc/modprobe.d/spidev.conf and adding to it the line "options spidev bufsiz=8192" When I do "cat /sys/module/spidev/parameters/bufsiz", it gives me "4096". 2) Add to /boot/cmdline.txt: spidev.bufsiz=8192 When I do "cat /sys/module/spidev/parameters/bufsiz", it gives me "4096". 3) cd /sys/module/spidev/parameters chmod 666 bufsiz echo 65536 > bufsiz did nothing. 4) /boot/armbianEnv.txt added options spidev …

i've built and started testing stretch ... it mostly looks pretty good with these issues found so far lircd - goes wild. systemd goes to 100% cpu it need to be blacklisted or the like. stopping/disabling it didnt work. i need to remove it to stop the cpu usage problem https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=860551 install python-wheel as default package as pip breaks without it eth0 has gone but seems to be a known issue https://irclog.whitequark.org/linux-sunxi/2017-09-19 and I see that hdmi has made progress (by smaeul) https://irclog.whitequark.org/linux-sunxi/2017-09-26

I'm testing the OrangePi+ and OrangePi+2 for review. I noticed my OPi+ was running a lot cooler than my OPi+2. Reason is difference in kernel. Just tried 5.8.5 on the OPi+ and it also ran as hot as the OPi+2. OPi+ with kernel 4.19.62 vs OPi+/OPi+2 with kernel 5.8.5 No fan idle OPi+ 50C No fan maxed OPi+ Throttle at 75C to 1.3Ghz at 80C to 1.2Ghz doesn't go higher than 80C Fan idle OPi+ 27C Fan maxed OPi+ 54C No fan idle OPi+2 58C No fan maxed OPi+2 Throttle at 80C to 1.3Ghz at 85C lower. Barely reaches 85C / Debian throttle at 75C to 1.3Ghz Fan idle OPi+2 33C Fan maxed OPi+2 60C 2 heatsinks+fan 64C w…

Dear Sirs and Madams! I am trying to reconfigure https://github.com/friendlyarm/h3_lichee BSP's kernel via make menuconfig which is producing following .config file: # # Automatically generated file; DO NOT EDIT. # Linux/arm 3.4.39 Kernel Configuration # CONFIG_ARM=y CONFIG_ARM_HAS_SG_CHAIN=y CONFIG_SYS_SUPPORTS_APM_EMULATION=y CONFIG_GENERIC_GPIO=y # CONFIG_ARCH_USES_GETTIMEOFFSET is not set CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y CONFIG_KTIME_SCALAR=y CONFIG_HAVE_PROC_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_HARDIRQS_SW_RESEND=y CONFIG_GENERIC_IRQ_PROBE=y CONFIG_GE…

Hi, I performed an apt-get upgrade on my system, and it installed the 4.13 kernel. After the reboot, i started getting the message "bad CRC - using default environment". I spent the whole day reading many threads but still didn't manage to come with a solution. I tried the symlink to /boot/dtb/allwinner from the PC2 forum, but with no luck. I bought this board recently, it is my first board and i am very new to this, although i have decent Linux knowledge. Could you point out what i might have done wrong or if i'm missing something?

Someone did an amazing job implementing the cubietruck sata speed for armbian. I am curious as to what was done. The other day I pulled read 75MB/s(via nautilus ftp) to my main computer from it. Would perhaps like to apply whatever the fix was to netbsd.

**Is this the correct location, or it should be at the other supported boards? It seems that DT overlays are not working root@orangepizero2:~# cat /boot/armbianEnv.txt verbosity=1 console=serial disp_mode=1080p60 fb0_width=1280 fb0_height=720 rootdev=UUID=b8899b39-b6cb-4718-bdbb-e1b39816db74 rootfstype=ext4 overlays=w1-gpio param_w1_pin=PC9 param_w1_pin_int_pullup=1 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u Boot log: Spoiler [41]HELLO! BOOT0 is starting May 13 2020 14:10:04! [46]BOOT0 commit : 593cf83 [48]set pll start [51]periph0 has been enabled [54]set pll end [56]unknow PMU [57]PMU: AXP806 [64]vaild para:1 select dram …

Hello. I want to test wireguard with the bionic nightlies on my OrangePi Plus 2e, but I'm unable to install the correct linux headers. In armbian-config, it show the "loading kernel modules" and the installing screen 2 times for a second, then goes back to the main screen. If I want to install with "sudo apt install linux-headers, it shows these possible options: linux-headers-udoo 5.52.180715 linux-headers-sun8i 5.52.180715 linux-headers-sun7i 5.52.180715 linux-headers-rockchip 5.50.180630 linux-headers-odroidxu4 5.52.180715 linux-headers-odroidc1 5.52.180715 linux-headers-next-udoo 5.52.180715 linux-headers-mvebu 5.52.1…

Hi, I am using newest Armbian Ubuntu on " Orange Pi plus 2 E" . All three comand lines_Terminal emulator,Xterm and UXterm-works okay when I type something,for example: sudo apt-get... But when I copy something,for example a command from the site,I paste it on Xterm,i see a with area. It dosn't paste. Please could you help me to fix this? Thanks, Sadegh

I am running a headless Bananapipro server that acts as an AP. Recently I found that its WiFi net was gone. In the log I found a crash of brcm: Dec 19 02:40:14 localhost kernel: [3919907.052132] ieee80211 phy0: brcmf_fw_crashed: Firmware has halted or crashed Dec 19 02:40:15 localhost kernel: [3919908.004319] ieee80211 phy0: brcmf_fil_cmd_data: bus is down. we have nothing to do. Dec 19 02:40:15 localhost kernel: [3919908.004360] ieee80211 phy0: brcmf_fil_cmd_data: bus is down. we have nothing to do. Dec 19 02:40:15 localhost kernel: [3919908.004372] ieee80211 phy0: brcmf_cfg80211_stop_ap: SET SSID error (-5) Dec 19 02:40:15 localhost kernel: [3919908…

I used armbianmonitor -r on my OPi Zero just like I did previously on OPi One. On OPi One everything is working fine. On my zero it doesn't display all the information for CPU. It shows: CPU total: undefined% (Sys: undefined%, User: undefined%, I/O wait: undefined%, Nice: undefined%) CPU frequency: 1.008GHz DRAM frequency: Not available Governor: ondemand Active CPU cores: 4 Vcore: undefined If I run armbianmonitor -m it shows these data I checked Allwinner_H3_Extended.conf and I noticed that it reads files from /tmp (/tmp/cpustat, /tmp/disktemp, e.t.c) On my OPi One I see these files On OPi Zero there is no rpim…

Hello Team, I am worked on Olimex Lime2 rev.G2 board but now olimex start delivering Rev.K board. I used the same Armbian Rev 5.35 image which is having kernel version (4.13.16-sunxi) & u-boot version v2017.09. On Rev.G2 Ethernet speed was as expected but in rev.K it is not working. By default board booted and comes with ethernet speed 100Mbps, but in this case Ethernet is not working (DHCP server unable to assign ipv4 address to eth0). Later i reduce the eth0 speed to 10Mbps it start working as expected but spped is 10Mbps Some more info about the ethernet issue which will help to understand the issue more clearly - …

Hello! The Cubieboard2 with mainline kernel support LCD through DVK522 board (LVDS connection)? The mainkernel support SPI?

Armbian_21.05.1_Nanopiduo_focal_current_5.10.34.img boots (updating via apt upgrade also causes it not to boot any more) Armbian_21.08.1_Nanopiduo_focal_current_5.10.60.img does not When I examine the SD card it hasn't expended from image (makes sense since the heartbeat never starts).

Hello everyone :-). I would like help, I checked on the Web and I found using the forum a script (that I modified) to trigger using DTS LEDs. I adapted the script found here at the end of the page: Topic 112-dtb-howto-add-leds I think that for the section "disk-activity" and "netdev" it misses options but I'm not a developer just a scheming. Can you please explain to me how to add options to the mentioned trigger? I searched a lot of time but did not find any information. Here is my script, everything works fine (compiled with armbian-add-overlay), but "disk-activity" and "netdev" do not work. I tested the write / read trigger on disk but did no…

Hi I only have an old monitor, and I thus need to use a HDMI-to-VGA-converter to work with my Orange Pi PC Plus. When powering the Orange Pi on, the green LED on the board is constantly ligthened. On the monitor, I get a black screen, after 4 s (or so) a totally red screen. No text. No graphics. Then after about 15 s, on the board the red LED starts to double blink. The red screen remains for ever. I have tested the Raspbian and Debian images available on http://www.orangepi.org/downloadresources/. They work fine with the converter. Alas, the preferred OS, "Orange OS" armbian, seems not to work. Board: Orange Pi …

I have been using this orangepi for several years now. Today SSH stopped working (it would hang indefinitely after password prompt) so I decided to restart it by removing and re-plugging the psu cable. After that it never appeared on the network again. 1) the board lights up: green / orange light on ethernet, and one green light on MB that turns on for ~25sec then turns off for ~10sec 2) I connected it to two switches with multiple cables, none of them show the ethernet port as active (no light on the switch port) Obviously due to 2) it doesn't appear on the router 3) microsd mounts fine on my pc, did a backup and flashed a clean image to no avail, wil…

Hello, I tried to introduce 4.4 Kernel 4.2.2 on Cubietruck, it was confirmed that it freezes at boot time. Login prompt does not appear. We have confirmed the problem in Debian Jessie. Best regards.

Hi Igor, I've a Pcduino 3 (not B or nano). Can you build an image for him? .FEX exists (https://github.com/linux-sunxi/sunxi-boards/blob/master/sys_config/a20/linksprite_pcduino3.fex) and I think the difference it's only a patch for GMAC. I'm newbee and I try to install your system on my board but I don't know how... I followed your post on Armbian...I created ' output ' but now? What am I doing? which files write on sdcard and how (dd?) May be I didn't see the tuto after to build image... Best regards JohnGO

hey guys, led folder is missing from /sys/class/ and even in /sys/class/gpio_sw/ led is included in fex file. can anyone tell how does linux load configuration from fex to orange pi ?

I know Banana pi had issues in the past connecting at gigabit speeds. I thought that was a fixed problem, though. I did a fresh Jessie server install today and it still connects at 100 megabit. Is there a user action that must be taken? According to http://linux-sunxi.org/LeMaker_Banana_Pi the GMAC wasn't supported in the community kernel but should be in later kernels. Is this still an issue? How does one set GMAC_TX_DELAY to 3? Is that a config file thing or a patch that needs to be applied? Are other Banana Pi owners just living with 100 megabit speeds? A bit of system information: ~> uname -a Linux bananapi 4.6.3-sunxi #7 SMP Tue Jul 5 16:23:41…

Hello, I am looking for the latest Banana Pi M1 server image but I only see the XFCE desktop version. Witch image should I use?

Hello, I encounter a strange behaviour with Lime2. When on battery and AC plug-in if I ask for a shutdown -h now, the board reboot by itself and the system does not stop. When on battery only, the board stop with the command shutdown -h now I read about those 2 variables CONFIG_MFD_AXP20X=y CONFIG_REGULATOR_AXP20X=y to set in u-boot/configs/A20-OLinuXino-Lime2_defconfig But after building the a u-boot package with compil.sh this setting does not have any effect... zgrep MFD /proc/config.gz command does not show the CONFIG_MFD_AXP20X=y variable Did I miss something, any ideas ? Thanks Florian

Hallo, i have an old istallation of armbian and it's working perfect , thank you Igor for your work..! i want to upgrade my stable debian wheezy without breaking nothing :p the current version of armbian is : Linux cubietruck 3.4.104-sunxi #1 SMP PREEMPT Fri Oct 17 16:13:30 CEST 2014 armv7l GNU/Linux and the : /etc/apt/sources.list deb http://ftp.it.debian.org/debian wheezy main contrib non-free deb-src http://ftp.it.debian.org/debian wheezy main contrib non-free deb http://ftp.debian.org/debian/ wheezy-updates main contrib non-free deb-src http://ftp.debian.org/debian/ wheezy-updates main contrib non-fre…

Hello, can anyone share his hostapd.conf where he managed to get HT40 "width: 40 MHz" running on orange pi lite 2 while it is in AP mode ?

Hi and Happy new year! I'm not so fluent in English, so please excuse me. I have Lamobo R-1 with HW mod (RT5572) and the main problem is that hostapd is giving error message at start: root@lamobo-r1:~# hostapd -d /etc/hostapd/hostapd.conf random: Trying to read entropy from /dev/random Configuration file: /etc/hostapd/hostapd.conf rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0 nl80211: Supported cipher 00-0f-ac:1 nl80211: Supported cipher 00-0f-ac:5 nl80211: Supported cipher 00-0f-ac:2 nl80211: Supported cipher 00-0f-ac:4 nl80211: Supported cipher 00-0f-ac:10 nl80211: Supported cipher 00-0f-ac:8 nl80211: Supported cipher 00-0f-ac:9 nl80211: Using driv…

Is someone tried to instal Kodi and is it work?

Hi, just a question to be discussed: Would it... 1. ...be possible to use F2FS as default filesystem for images using the vanilla kernel? 2. ...make sense to use it? benchmarks show that write operations could get a huge boost in comparison to ext4. i believe write operations are quite slow right now (using cubietruck with sd-card) What do you think?

Hi, I have downloaded and installed Armbian to my Pcduino3 board with the legacy kernel 3.4.113. But now I want to downgrade it to the kernel version 3.4.79. Is there any way to do it? Regards,

Thanks to the latest Armbian and my own script - I now have a NanoPi Neo (two of them actually) running everything I want - Node-Red, Mosquitto, SQLITE3 etc..... got control of serial ports - marvelous. I have only one problem - I have no idea despite several experiments - how to get WIFI working on the standard cheap Wifi dongles you get on Ebay. (usually say 802.11n on the black plastic end). Anyone succeeded with this? Pete.

I just installed 4.2.3-sunxi on my Banana Pi (original model.) Everything seems to work nicely except the console mouse (gpm.) I run keyboard and mouse on a "GreenAsia Inc. USB to PS/2 Adapter" and have never had a problem with that setup, including Raspberry Pi and Bananian on the BPi. Both keyboard and mouse work under X but on the console only the keyboard works. This is logged when I plug in USB: Nov 13 06:21:25 bpi kernel: [ 1963.223307] usb 3-1: new low-speed USB device number 4 using ohci-platform Nov 13 06:21:25 bpi kernel: [ 1963.446399] usb 3-1: New USB device found, idVendor=0e8f, idProduct=0020 Nov 13 06:21:25 bpi kernel: [ 1963.446427] usb 3-1: New USB d…

Hello Could You advice it` s possible to run emulator for SNES game on armbian at OPI WIN. I`m already run NES game but try to instal other SNES emulator don`t work Thanks in advance.

I've tinkering with this board, and trying to boot from spl, but the boot halts after reading the temperature sensors, which does not happen when booting from the sd card. After booting from the sd card I read the sensor that causes the problem # cat /sys/devices/virtual/thermal/thermal_zone0/temp 51740 I found in a forum some kernel patches to mitigate this: https://forum.manjaro.org/t/support-for-orangepi-zero2-h616-ddr3-zero3-and-zero-2w-h618-lpddr4/154679 Why does it fail when booting from spl, and not when booting from the sd? Here is the system info: # cat /etc/armbian-release # PLEASE …

Dear Igor, first of all: Thank you very much for the work on armbian! My problem now is: I installed armbian on my cubieboard 2 (on 16 GB SD card) and first everthing went fine. I did all the management via putty and ssh but since a couple of days I can't ssh anymore. That means, ssh login with username and password is succesful, but I do not get any command line. Besides I get a couple of other problems: One is, when I boot up, I takes about 10 min, since problems with "LSB", this means: It takes about 5 minutes withe the message: "a start job is running for LSB: raise network interfaces" Similiar problems occur during shutting down the system (…

Someone can help me with detail instruction: how I can enable touchscreen trough gpio on OrangePi Plus 2. Screen setup to 800x480 but cant enable touch, because I am beginner.

Hello Armbian-community. I'll make this short: I've got a NanoPi M1 running with the latest available "Armbian_5.25_Nanopim1_Debian_jessie_default_3.4.113.img"-image on a 16GB Class 10 microSD. When trying to run "modprobe g_multi" as root, the following error occurs: modprobe: ERROR: could not insert 'g_multi': No such device I want to have a multifunctional gadget via the OTG-port. It should mount ISO files as CD-ROM (in which I succeeded so far with: "modprobe g_mass_storage file=/home/user/iso.iso stall=0 cdrom=1 && echo 2 > /sys/bus/platform/devices/sunxi_usb_udc/otg_role") and forward keyboard strokes made at th…

I just installed Ubuntu on A20 Cubieboard2. I have two situations. First boot stops if no ethernet connection present. Because of location issues need to use wifi by default. I need to have startx run without me having to login first and manually issue startx command. Other than this two issues all seems fine. Any help will be appreciated. Thanks.

Hello,I have a bananapi m2+ I would like to install kodi version 17 to the standard repositories is the only version of 15 which doesn't suit me. tell me how to install the 17 version? I'm new to Linux and don't understand much,if there is a possibility lay out the user manual which would have helped with the installation. I want to install on server version armbian and that would be after the launch of the banana pi automatically instead of a desktop was loaded kodi interface, so it is possible to do?

hi when i try to play a video player performance is very low on armbian but when i install android on my board video player performance is good Enoughwith mx player app i try improve performance with overclock cpu but its not helpful how can i improve performance of video player on armbian ? and its possible to play h.265 video and 3d video?

I am trying to setup a logitech squeezebox server on an Orange Pi Zero so that it can be carried around and serve my collection from a large micro-sd card. This is the 3rd iteration of this already (first was given as a gift, 2nd got fried by 12V, and now this one) and in the past I've been using hostapd to connect while away from home. I'd like to explore the possibility of using a Bluetooth Personal Area network, but I am not sure if there is a stack that can achieve this for me. The idea is that I would use bluetooth instead of wifi to connect to the orange pi zero and establish a tcp/ip connection that would allow me to control the server using the phone…

good night, is ethernet and usb a shared hub on Orange Pi Plus 2E and H3 SOC? i get max dl\up speeds on speeds tests and good write and read speeds but when i dl something it max at half my Internet speed thanks

root@orangepipcplus:~# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 0.0.0.0 0.0.0.0 U 1002 0 0 eth0 0.0.0.0 192.168.30.1 0.0.0.0 UG 1024 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 192.168.30.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0

I installed the kernels from and flashed them to sd card. Then i copied the modified .ko files from image that i built for latest non-rt kernel using the compile.sh. My orange pi zero is running rt version. When i try to modprobe the modified and copied module it gives me error: modprobe: ERROR: could not insert 'libcomposite': Exec format error I read that incorrect arch could cause this so i ran the file command. libcomposite.ko: ELF 32-bit LSB relocatable, ARM, EABI5 version 1 (SYSV), BuildID[sha1]=3a49e12c7809bbbdbdc3c5c5bd0fcd53e77dde44, not stripped i think module i built is not compatible with rt kernel i downloaded. I need to rebuild kernel…

Basically, just did 3 consecutive runs of iperf3, and they look like this. And it is not cpufreq, since setting it to performance on all CPU cores does not affect things. Using the current stable Debian image with kernel 6.1.30. Any ideas? $ iperf3 -c 192.168.103.156 Connecting to host 192.168.103.156, port 5201 [ 4] local 192.168.0.101 port 58758 connected to 192.168.103.156 port 5201 [ ID] Interval Transfer Bandwidth Retr Cwnd [ 4] 0.00-1.00 sec 27.3 MBytes 229 Mbits/sec 0 201 KBytes [ 4] 1.00-2.00 sec 26.4 MBytes 222 Mbits/sec 0 195 KBytes [ 4] 2.00-3.00 sec 26.3 MBytes 221 Mbits/sec …

Hello, I have't used my old Cubietruck for years but would like to use it again in a project. I downloaded the new Armbian version: Armbian_community_25.2.0-trunk.124_Cubietruck_noble_current_6.6.62_xfce_desktop.img and installed it. There is console display just fine through HDMI, but not graphical display. There seems to be some trouble before as in this discussion: I downloaded this image: https://github.com/IGNNE/cubietruck-armbian-unofficial/releases/ and it seems to work. But when it updates itself, the graphics is gone again. So - is there some old dr…

Thanks for providing the new Buster image (5.4.7) for Orange Pi One Plus. All the essential stuff works well, giving me new software possibilities. As a technical feedback, I'd just like to mention 1) the red light keeps shining (instead of turning green, but Armbian runs very well, anyway) 2) an attached monitor doesn't receive any signals (but I prefer SSH anyway) 3) the console keyboard layout wouldn't accept any changes (but using SSH, that doesn't make any difference now). Everything else in armbian-config worked fine. Great tool!

I just run an "sudo apt upgrade" and my 22.05 system was upgraded to 23.8.1 As a result WiFi stopped working. The wireless interface disappeared and can not be configured with armbian-config. On the positive side it seems like the load bug is now fixed, load can now be 0.0.0 at its lowest as opposed to 1.1.1 before. is there a way to revert back to the old kernel with Armbian?

I cannot use my dmesg in a normal way anymore. It is flooded by these messages: [ 2828.613264] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x48, dev addr: 0x48) [ 2828.613724] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x48) [ 2828.613906] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x48, dev addr: 0x48) [ 2828.614101] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x48, dev addr: 0x48) [ 2828.614485] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x48) [ 2828.614660] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x48, dev addr: 0x48) [ 2828.61483…

I have installed "Armbian_5.54.180727_Nanopineo_Debian_stretch_next_4.17.11" in the eMMC..My doubt is always boot from eMMC, If blank sd card is inserted in the slot.

Please give me your recommendation for my OPiPC+ to use Armbian and Asterisk I see there are 3 options for Armbian for my model. I am not good with linux and would prefer a GUI for both Armbian and Asterisk. Also I am wanting as "Lightweight" as possible. I will not be using the OPi for anything else but a phone system. Also could you give me steps to take to add Asterisk to Armbian. Thanks

Hi there, I want to migrate system on OPi PC+ from 32GB uSD card to 16GB card. System is small enough to fit on 16GB, but too large for 8GB eMMC (amazingly fast according dd). How to do it? My idea is: - copy (raw, using dd) first 8192 sectors from 32GB to 16GB, - then remove partition (32GB) and recreate it with 16GB size, format using same EXT filesystem, - copy (on another computer, or "simple" Armbian installed on eMMC) partition contents using rsync. Will it work? Will there be no issue with different UUID of new partition?

Hi, is my Cubieboard is damaged? Couple days ago my server was suddenly turned off. When I checked, it turned out, that the Allwinner is very hot. So I added a radiator and run the Cubie with serial console. Seems like everything is ok, but temperature... almost 50*C. log_15082016_2.txt

I got a banana pi plus like the one this web page https://www.armbian.com/banana-pi-plus/ and downloaded legacy jessie server on it. After applied the last step on the page： sed -i '1isetenv fdtfile sun7i-a20-bananapi-m1-plus.dtb' /boot/boot.cmd mkimage -C none -A arm -T script -d /boot/boot.cmd /boot/boot.scr ln -fs bin/bananapim1plus.bin /boot/script.bin reboot the board just can't boot up. anyone have same problem?

Hi friends, need for your advice and experience. How can i disable а boot from sd card after moving Armbian(latest vesion) to EMMC? My board is Orange Pi Plus 2e. I would like to use sd card in Armbian, but a boot terminated each time when a card is inserted. Any advice or a link? THANK YOU!

I'm running OpenElec on a NanoPI-M1 and one thing missing is having the screen blanked when the screensaver kicks in, allowing the monitor to power down. In Kodi there's no option to do it, unlike when running in other OS. Probably someone is going to direct me at CEC but that does not work for me as I have a PC monitor connected to the board through a HDMI->VGA adaptor. I've read in the sunxi docs that the '/sys/class/graphics/fb0/blank' sysfs entry should control blanking for the framebuffer, therefore blanking the HDMI output, but it either does not work that way or at all, as nothing happens. On the RP world there is a command line utility that can enable/disabl…

Hey kids, it is me, again! So, this time I found out (well, you maybe knew it before and I am dumbing around again) that voltage control does not work on Banana Pi (at least) mainline kernel. Well, if I am supposed to change it in linux-mainline/arch/arm/boot/dts/sun7i-a20.dtsi. I tried to reach 1248000kHz, which is, of course, unstable. So I was adding and adding voltage, until I was too afraid to continue (1650000mV ). But BananaPi was unstable the same way (freez after few minutes of FTP transfer), no more (bad charger) or no less (would still need more voltage). So after few hours of re-compiling source and listening wonderful music I tried this: 1248000(kHz)…

I have an orange pi pc Just installed debian When it comes up on my TV, I can't sell the first 3 characters of screen, and it runs below the bottom of the TV so I can't see the last line or so How do I fix?

I am currently trying to upgrade my kernel from 3.4 to 4.14 and it is working quite well for my needs. But i have a problem i have not found a solution for, i can not set the PE00-11 pins as gpios. Acutally i cant set or configure them at all. I am using the /sys/class... export and writing via echo direction and value. For all other GPIOs it works perfectly fine exept for those 12 (and the IR0-pins PB3 and PB4, those are also not accessible). I tried really a lot already: stripping down the kernel to only the most essential modules, deactivating almost everything in the dts file, using different images... but in essence, as soon as i c…

Hello, When I flash the newest version of Armbian debian, and plug it into my Orange Pi Lite, nothing is displayed on my monitor, even if the led is green. My monitor is 4K LG display. With Debian, the HDMI output is not reconized. I tried with Armbian Ubuntu, and the instalation guide is displayed, but the edge and the bottom of the screen are cut. After one reboot, the screen is entirely black and I can't do nothing. Any help is welcome

Hi, is there a way to enable HDMI output for a cubietruck? During boot I get some display output till "starting kernel" than the screen gets black.

Hello, i have a Banana Pro and i want to switch to Armbian from Bananian. Only to write the image to the sdcard does not work. It don't boot (no green LED, no access with ssh). Is there a problem with the bananian u-boot? To change the u-boot with the lemaker script to default does not work, there is an error (https://github.com/LeMaker/scripts). Can somebody help me? Michael

Hi! I need some help. I built a little torrent server, home media center from opipcplus. It runs transmission all day all night with a heatsink and it keeps the cpu temp under 55°. But if i start kodi or other player the temp jumps to the sky near 80°. i bought a cooling fan and with the heatsink it keeps the cpu under 35° without any problem. its great but it noisy and frustrating. How can i control the pins to automatic turn on and off the fan? can someone send a script or anything help? thank you

After upgrading my armbian (orange pi pc plus and Orange Pi Plus 2) today, Orange Pi PC Plus mac address changes to 6a:59:53:1a:4d:c1 from AA:0A:75:AD:D2:CE. Here is dmesg (Orange Pi PC Plus) output but I dont found anything related to mac address there [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.4.113-sun8i (root@devel) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #28 SMP PREEMPT Thu Feb 2 02:01:28 CET 2017 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: sun8i [ 0.0…

I've installed Armbian_5.14_Cubieboard_Debian_jessie_3.4.112_desktop.7z and It initially worked. I tested video files playback (I think it was mpv player) and it worked smoothly, no video lag. After 4 or 5 boot-ups, I'm no longer able to start armbian. I just see u-boot starting and then (when the kernel is going to be loaded (message: "Starting kernel ...")) I see mess on screen and cubieboard is powered off (red power light goes down, also networking leds). I use HDMI output (unfortunately I do not have serial cable to try debug it maybe further). What I tried so far, without success: -changing SD card for another one (8GB cat4 for 8GB cat10) -replacing power supply …

Can someone post the printenv for a NEO PLUS2 because i think i f*** up my device and doesn't boot from SD or USB .... the only i get is the boot menu. Or any ideas to help me to fix this ?

orange pi zero uboot eth have only 10baseT, HDX => mii info PHY 0x00: OUI = 0x50005, Model = 0x00, Rev = 0x00, 10baseT, HDX PHY 0x01: OUI = 0x50000, Model = 0x00, Rev = 0x00, 10baseT, HDX any way change to 100 full duplex at boot time because tftp work fine but slooow after linux kernel starded normal 100 full duplex eth

Hello there, I am looking for some feedback/suggestion about an issue I have. Installed Armbian legacy kernel just yesterday. Then I have plugged https://www.olimex.com/Products/USB-Modules/MOD-WIFI-AR9271-ANT/ to enable wifi and found out I missed required firmware. I installed such firmware (htc_9271.fw) first by Ubuntu linux-firmware package, then tried with armbian-firmware-full, then I have downloaded from here http://linuxwireless.org/download/htc_fw/1.3/ (putting in /lib/firmware and after failing tried also /lib/firmware/ath9k_htc like package manager does. I have also tried compiling my own version from here https://github.com/qca/open-ath…

Hi All! I am running latest jessie desktop, and experience problems with pre-insatalled mozilla. There is no sound, except on the youtube site, that runs html 5 player. What can i do to bring sound back? All the online players looking like playing, but i hear only silence.

has anyone managed to get one of these boards to function, I'm obviously missing something...

BACKGROUND: Back on June 27th, I posted my questions regarding my wish to have certain kernel features activated (or not) by default in the Armbian/Debian kernels of the time -- specifically since I wanted to activate 'PPS' features in order to build a Stratum 1 GPS/PPS timeserver: Kernel Option Requests? Here are the 'old' instructions that I used back in June: ORANGE PI PLUS H3 with GPS/PPS I ended up needing to install VirtualBox with an Ubuntu 16.04 environment, and successfully created what I needed (i.e. 3.4.113-PPS-sun8i). I was also eager to create a much newer kernel, but that failed (i.e. 4.11.5). My Orange Pi PC…

Hi, I have some problem about softAp mode. I am using orangepi+ and, Armbian debian jessie server 5.20version. I want to connect web page using SmartPhone. and connect other AP(Client ap mode). so i set dhcpd server. and hostapd. But, If i use "sudo iwlist wlan scan" command , kernel is rebooting with panic.. how can i set hostapd.? It's my setting. /etc/hostapd.conf ctrl_interface=/var/run/hostapd ctrl_interface_group=0 macaddr_acl=0 auth_algs=1 ignore_broadcast_ssid=0 wpa=2 wpa_pairwise=TKIP rsn_pairwise=CCMP wpa_passphrase=12345678 driver=nl80211 wme_enabled=1 wpa_group_rekey=86400 interface=wlan0 hw_mode=g channel=6 ssid=TEST_AP /etc/network/interfaces…

Hi, what are currently the options of controlling 433Mhz sender/receiver devices from an orange Pi zero 3? Currently the gpios are no longer exposed via sysfs but you could re-enable that feature by compiling a new kernel with the proper configuration. Then wiringpi would work again and you could use 433Utils. But what would be the options without compiling a new kernel? What 433Mhz library exists that uses the new way of controlling the gpios? I am a bit confused about the current state of affairs, please enlighten me...

Hi, Messages flooded with the i2c0 messages after the NeoAir boots as showing below: [ 10.234498] dhd_module_init: Exit err=0 [ 10.240493] systemd[1]: Listening on Syslog Socket. [ 10.246332] systemd[1]: Starting Journal Service... [ 10.360420] systemd[1]: Started Journal Service. [ 10.813583] systemd-udevd[179]: starting version 215 [ 11.191615] twi_start()434 - [i2c0] START can't sendout! [ 11.197938] twi_start()434 - [i2c0] START can't sendout! [ 11.204329] twi_start()434 - [i2c0] START can't sendout! [ 11.210906] twi_start()434 - [i2c0] START can't sendout! [ 11.221376] twi_start()434 - [i2c0] START can't sendout! [ 11.228399] twi_start()…

I there i use the update my orange pi zero to latest version 04/05/17 and no simply dosen´t boot anymore! any thing i can do?

Hi, Just a quick question as Debian Stretch has been out for a while now: Will there be an official upgrade of ARMBIAN for the Cubietruck (Cubieboard 3) at some point or is there a simple doc on how to upgrade the distribution? I run ARMBIAN with the legacy kernel (3.4.113-sun7i). Everything required for the system boot is in the NAND while the root and /home partitions are on the sdd. Would it be possible to upgrade to Stretch just by replacing the version name in the sources.list file? If there won't be any automated ARMBIAN upgrades to Stretch for this device. Would you recommend using the official Debian distribution (and bo…

Hi, I am using the last image (kernel 11.5) for banana PI M1 and I successful use the nand-sata-install script. now I would like to copy the bootload to 128M SDCard Can someone help me?

When I do a reboot the Olimex Lime2-emmc shuts down. No more information is shown on the display. This happens with the latest Armbian_5.31_Lime2_Debian_jessie_next_4.11.5 image from the website. It also happens with a self-build image with u-boot v2017.07 and v2017.05 Any ideas? Or debugging directions? I am out of options after 2 days...

Hello, Is any way to use the full cpu potential from the board. I have tried the environment settings from one of the threads where gpio-regulator-1.3v is introduced but without success. Thank you Sent from my D6503 using Tapatalk

Hello, I just started to use my old BananaPi M1 (Armbian 23.8 Bookworm) to check sensor values by onewire and i2c. At last there was no problem with onewire But I cannot get I2c to work. /boot/armbianEnv.txt overlay_prefix=sun7i-a20 overlays=i2c2 w1-gpio param_w1_pin=PI3 For onewire I had to define "param_w1_pin=PI3" even if my onewire sensor is connected to GPIO7. for I2C I checked "lsmod | grep i2c" but couldnt find anything. So ieven if it is not correctly activated, I could run "i2cdetect -y 2" and could find my sensor at 0x76 but couldnt communicate with it. I think I need to load "i2c-bcm2708 i2c-dev". Ho…

We are in the process of migrating from NanoPI NEO's to NanoPI NEO Core's as part of that we are moving to mainline NEO Air / NEO Core images. I noticed that audio playback is soft / fades in at the start of the file. This only seems to occur on mainline images. Thoughts?

Hello, I am setting up a filserver, using a BPi and a WD Red 3TB connected to the sata port of the BPi. The BPi runs armbian v4.5 with vanilla kernel. For the first tuning I used the recommandations from tkaiser (thanks a lot for that). The only difference is, that I use ondemand as govenor and the frequency values out of the armbian image (thanks a lot to igore for the great work). root@bananapi:~# sysctl -a | grep mem net.core.optmem_max = 65535 net.core.rmem_default = 163840 net.core.rmem_max = 8738000 net.core.wmem_default = 163840 net.core.wmem_max = 6553600 net.ipv4.igmp_max_memberships = 20 net.ipv4.tcp_mem = 8874 11832 17748 net.ipv4.tcp_rmem = 8192 …

Hi guys! I have a problem with Orange Pi 3. After a night leaving the small board turned on I reboot the board and try to use a Bluetooth connector it shutdown. Again and again the same problem. When I touched the board it was so hot. Even when I use outside the case the board can't support a process for at least 30 minutes without turning off. I got the outputs of dmesg. As I don't know, I am a replay newbie, I ask for help here. Best regards. Paulo

Hi all, I've been using a banana pi as a home server since forever. It's currently running bananian with a legacy kernel. I want to use docker to make it cleaner to use so mainline is needed. My banana pi is running off a 256Go SSD (SATA) and connected through a Gigabit Switch (that's why I did not find many replacement over the years, both low power, SATA and Gigabits are hard to find even with Hardkernel stuff). So first what's running on my server now : * nzbget * nfs server * nginx as reverse proxy * nginx + php * MQTT server (Mosquitto) * MQTT relay server (with mqttwarn) * homemade domotic stuff For all of this, I guess docker will be o…

Hi all, I am using NanoPi-Neo Air and my application is just logging binary data to a file. The board is powered by usb from a pc. I can dump and list to see binary data inside the file but after unplug power from usb then power up the board from usb again, I found the binary data is gone or some errors data, unknown data appended. Do you guys have same issued? or any suggestions? Thanks in advance

Hi, we experience change in owner:group in /var/log. Eg. mosquitto folder requires mosquitto:mosquitto and is changed to root:root. After this change mosquitto service is down. Any pointers are very much appreciated. Many thanks. Rostislav

I'm trying to wake up an OPi PC using an IR remote following these instructions http://www.orangepi.org/orangepibbsen/forum.php?mod=viewthread&tid=2048&extra=page%3D1 bits 16 flags SPACE_ENC|CONST_LENGTH eps 30 aeps 100 header 9004 4560 one 532 1703 zero 532 593 ptrail 541 repeat 9015 2283 pre_data_bits 16 pre_data 0x1CE3 gap 139912 toggle_bit_mask 0x0 begin codes KEY_POWER 0x48B7 KEY_0 0x00FF KEY_5 0xA05F end codes end remote . [s_cir0] ir_used =…

Hi! I need some help in order to install Node-RED over Armbian Wheezy on Cubieboard1 can anyone give me help?

I have searched the forum and the internet and am having a lot of trouble finding a guide on how to covert the OTG on my OrangePi One to a USB port. (I am assuming it is possible to do.) I believe the current configuration for the OrangePi One is one usb and a OTG. I would also Like to be able to use the OTG as a USB port when I run OpenElec as I would like the second USB to plug in the new Optional Bluetooth dongle. Seasalt

hi all, i have a doubt about cubieboard3 and cubietruck 3.4.104-sunxi. Tipically use this board with network and SSH , but sometimes i need attach monitor VGA and sometimes monitor HDMI. Now work only VGA, HDMI never works. my /boot/cubietruck.fex is: [disp_init] disp_init_enable = 1 disp_mode = 0 screen0_output_type = 4 screen0_output_mode = 4 screen1_output_type = 0 screen1_output_mode = 4 fb0_width = 1024 fb0_height = 768 I can setup output cubietruck autosense? regards

I am using Armbian_20.05.4_Lime-a64_focal_current_5.4.45_desktop.img.xz and I try run glxgears on Olinuxino-A64 with Lima. When I running glxgears I see 117 frames in 5.0 second = 23.313FPS. Also mouse response so slow on desktop. It is understood from here Olinuxino-A64 doing software render. Please correct me if I am wrong. I am new at this job and I have difficulty in fully understanding the problem. Is there a way I can get high FPS in glxgears using Lima? What exactly is problem here? Sorry if I ask silly question. Thanks. Below are some outputs for the board I use. dmesg | grep "lima" output: [ 8.579828] lima 1c40000.gpu: IRQ ppmmu2 not found [ …

Hi, How to build the Phoenix image from the Cubieboard2 NAND-flash? If anyone have idea I would appreciate. regards, Rassul.