Allwinner sunxi

When I login on the console, there is this display with a bunch of information, including the CPU temp. I have need to keep track of my CPU's temp, since it seems to be overheating (I have a heat sink on it, but does not seem to be enough -- I have a fan on order). I want to be able to check the temp from time to time, so I would like to run at least the part of the login banner program. What program is that? I am not seeing anything obvious in /bin.

diagnostics listing of Orange Pi Zero 2W http://ix.io/4Lwr Not sure if this helps..but the stock build is lacking...plus I am getting 1.0 cpu usage at idle Orange Pi 1.0.0 user-built System too busy for benchmarking: 16:33:21 up 25 min, 3 users, load average: 1.15, 1.03, 0.92 System too busy for benchmarking: 16:33:26 up 25 min, 3 users, load average: 1.14, 1.03, 0.92 System too busy for benchmarking: 16:33:31 up 25 min, 3 users, load average: 1.13, 1.03, 0.93 System too busy for benchmarking: 16:33:36 up 25 min, 3 users, load average: 1.12, 1.03, 0.93 System too busy for benchmarking: 16:33:41 up 25 min, 3 users, load average: 1.11, 1.03, 0…

Hi, I have a question about distro upgrde. This is the information on welcome screen: Packages: Ubuntu stable (jammy), possible distro upgrade (noble) Support: DIY (community maintained) I checked the release info on https://www.armbian.com/orange-pi-plus-2e/ and the noble is available. I used sudo apt dist-upgrade and it found no upgrade. Is there any wrong with that? And how I can do the dist-upgrade except writing a new image?

i have just downloaded the new version (dated 5-8) for jessie 4.1.4 for the cubietruck. it runs till it gets the greetings screen but then hangs and says: time timed out waiting for device dev-ttyS).device. depend dependency failed for serial getty on ttySO. -- i had a hdmi monitor, but then connectted a vga monitor (both show the initial informations) - the same result. what did i wrong? andrew ps. thank you for adding the upgrade using ppa!

I just installed 4.2.3-sunxi on my Banana Pi (original model.) Everything seems to work nicely except the console mouse (gpm.) I run keyboard and mouse on a "GreenAsia Inc. USB to PS/2 Adapter" and have never had a problem with that setup, including Raspberry Pi and Bananian on the BPi. Both keyboard and mouse work under X but on the console only the keyboard works. This is logged when I plug in USB: Nov 13 06:21:25 bpi kernel: [ 1963.223307] usb 3-1: new low-speed USB device number 4 using ohci-platform Nov 13 06:21:25 bpi kernel: [ 1963.446399] usb 3-1: New USB device found, idVendor=0e8f, idProduct=0020 Nov 13 06:21:25 bpi kernel: [ 1963.446427] usb 3-1: New USB d…

I am using the latest Armbian image on OPI+. I had a requirement to read a 64Gb USB flash formatted under Windows with the extFat filesystem. Much to my surprise it didn't mount. I thought it was a hardware problem 1st. But then it appeared, that mount doesn't support the the extFat filesystem by default. It is necessary to add the extra packages, but I didn't succeed: root@orangepiplus:/# apt-get install exfat-fuse exfat-utils Reading package lists... Done Building dependency tree Reading state information... Done The following NEW packages will be installed: exfat-fuse exfat-utils 0 upgraded, 2 newly installed, 0 to remove and 9 not…

Hi, I can't seem to mount any drives with journaled user/group quota. I just get this error: root@bananapipro:~# mount -o rw,defaults,nofail,user_xattr,noexec,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0 UUID=56790abd-531d-43b7-8cf8-9bfc85105f6a /media/56790abd-531d-43b7-8cf8-9bfc85105f6a mount: wrong fs type, bad option, bad superblock on /dev/sda1, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so. If I run the mount command without the quota stuff the drive mounts without any problems and is browseable.

Hello, Is there any way to programmatically interact with HDMI on Banana Pi/Pro? Ideally I would like the following: Learn the current state of the HDMI monitor (and/or receive notifications): not connected, connected and turned off (in standby), connected and turned on. Turn off the HDMI monitor (put to standby). Turn on the HDMI monitor (exit standby). Thank you in advance!

Hi, Seen some posts where mentioning that depending of the version of kernel there is either FEX or DTS usage, old ones called Legacy, using FEX to define GPIOs and Peripherals pins. Wit Mainline Kernel, is using DTS. Yet in the recent kernel (dev) armbian builds, eg armbian 5.21, kernel 4.7.6 (on H3, NEO), seen the /boot containing all the FEX stuff script.bin etc. Is FEX still used in the mainline kernel builds? C:\Christos>ssh christos@192.168.1.131 christos@192.168.1.131's password: setsockopt IP_TOS 16: Invalid argument: _ _ ____ _ _ _ | \ | | __ _ _ __ ___ | _ \(_) | \ | | ___ ___ | \| |/ _` | '_ \ / _ \| |_) | | | \| |…

I'm trying to build an A2DP server from either OPi Lite or Zero (whichever seems easier). As neither board has BT built-in I'm planning on using some cheap USB BT dongle. Web stores are filled with dongles, but info about their compatibility with Linux (and especially Armbian's legacy kernel) is not that readily available. Has anyone found a dongle that "just works" with OPi Lite or Zero? If yes, care to share e.g. Ali Express link or similar?

With an earlier version of Armbian (Server) I was able to use my Orange Pi Pc + to feed data back to Flightaware, Flight Radar, Planefinder, ADSB Exchange. An upgrade put an end to that in the latest version. Is it possible to get this working in future Upgrades of Armbian? Piaware Install

Hello, first of all many thanks to all the community that keeps this project alive. I recently bought a NanoPi NEO2 board and of course decided to drop the OS provided by Friendlyarm and give a try to Armbian's Ubuntu build for this board. Everything seems to work just fine, however I'm unable to get a reading on the CPU Frequency. I tried multiple tools and commands but somehow all end up with something like "cpuinfo_cur_freq: No such file or directory. For instance, here is the output of armbianmonitor: armbianmonitor -m Stop monitoring using [ctrl]-[c] Time CPU load %cpu %sys %usr %nice %io %irq CPU/usr/bin/armb…

Hi all ! I try to turn off ethernet leds on Nano Pi Neo. I don't use network-manager (which disables leds when ethernet cable is disconnected) because I need to use ifup and ifdown... I tried to see (without success) : cd /sys/class/leds cd /sys/class/net/eth0/ h3consumption -e off I know that it's possible on banapi (with a github library), is it possible on nano pi neo ? Best Regards

Hello guys, I am trying to blinking POWER_LED on my orange pi lite using google firebase but I couldn't find any resources on internet.... Here is my armbian info; http://sprunge.us/RhTM I want to develop ioT application using orange pi zero coz it has internal ethernet and wifi connection options and it is cheap. What I want to learn is: - I want to develop my ioT application using python - which version OS I should load - proper GPIO or related library for controlling GPIOs and rs-485 and i2c communications Thanks.

My problem with Cubieboard3: input audio file hallo.mp3 with content "Hallo Otto" play hallo.mp3 --> Output on analog audio clipped to: plop lo otto plop It looks like the audio channel must be switched on and off for use. What can I do?

Am running Orange Pi Lite With Debian Stretch uname -a: Linux orangepilite 4.14.18-sunxi #24 SMP Fri Feb 9 16:24:32 CET 2018 armv7l GNU/Linux was wondering what i am missing here ?

I am trying out the latest Armbian Debian Buster release for a Nanopi Neo Air. It is working fine. I've loaded Armbian into the eMMC and I can boot off of it. I have done `apt update && apt upgrade`. Using armbian-config, I have configured Wi-Fi and can SSH in. However, Bluetooth does not work: # systemctl status ap6212-bluetooth.service * ap6212-bluetooth.service - LSB: Patch firmware for ap6212 adapter Loaded: loaded (/etc/init.d/ap6212-bluetooth; generated) Active: failed (Result: exit-code) since Thu 2019-10-24 04:12:56 UTC; 6min ago Docs: man:systemd-sysv-generator(8) Process: 1928 ExecStart=/etc/init.d/ap6212-bluetoot…

Basic information: Board: Orange Pi Plus 2e Image: Armbian_19.11.3_Orangepiplus2e_buster_current_5.3.9.img Issue: No sound on HDMI output There has been quite a few suggestions for this issue here and and OrangePi Plus and none works for me. Tried following: 0. sudo apt-get update && upgrade 1. Created and Changed /etc/asound.conf Version 1: pcm.!default { type hw card 1 } ctl.!default { type hw card 1 } Version 2: pcm.!default { type hw card 1 device 0 } ctl.!default {…

If I convert rootfs to btrfs do I need to rebuild /boot/initrd.img-5.4.20-sunxi. E.g. is it enough to convert ext4 to btrfs on another PC and replace rootfstype=ext4 by rootfstype=btrfs in /boot/armbianEnv.txt? Armbian 2020.02.1 mainline with default kernel, orange pi plus I need a compression because OPI+ supports cards up to 32 Gb only. Thanks in advance.

Hi there, I need help in finding the lates Debian Buster image for my R1. Please can you point me to the latest version ? Many Thanks Wollik

Hi guys! I have a problem with Orange Pi 3. After a night leaving the small board turned on I reboot the board and try to use a Bluetooth connector it shutdown. Again and again the same problem. When I touched the board it was so hot. Even when I use outside the case the board can't support a process for at least 30 minutes without turning off. I got the outputs of dmesg. As I don't know, I am a replay newbie, I ask for help here. Best regards. Paulo

Heya, Configuration :: Friendlyarm NanoPi Neo (Allwinner H3) Matrix TFT2.8 (https://www.friendlyarm.com/index.php?route=product/product&product_id=102) Armbian Release: Bionic 5.8.y found here: https://www.armbian.com/nanopi-neo/ I have this st7789v-based display working on spi0.0 by utilising a custom overlay tft28.dts as below, but I cannot get the ads7846 touchscreen controller to use an additional gpio chip select (ie: spi0.1) because the ads7846 driver seems to be holding that additional cs line in a 'logic 0' state at zero volts. I believe the hardware is not at fault because it works correctly using the Friendl…

I built an adapter for a SPI interface SD Card Reader (https://www.ebay.com/itm/161201009722). I'm assuming I need to add in an overlay to make this reader show up, but I am not sure what that should be.

Has anyone had any success with running a current/semi current OS and the NAS/RTC Enclosure/Hat from FriendlyElec. I was never impressed with the NAS/OpenMediaVault image that shipped with the board/hat. I have attempted to strip OMV out of the device and move the device forward with some success. The the Kernel is stuck at v4.14.52. But I would prefer to load a clean current OS and potentially use the correct overlays to enable the extra USB Ports, USB to SATA Bridge and RTC features. Question is does anyone have any information/guide to use a current version of Armbian/Community and the correct overlay file(s) to allow the the JMicron USB to SATA interface and …

Hi there, I've been trying for a few hours now to get the GPIOs working with the mainline kernel (ARMBIAN Debian GNU/Linux 8 (jessie) 4.5.2-sunxi). According to the board layout photo, I am using PG0, PG1, PG2 and PG3. With the legacy kernel, they export as GPIO1-PG0 a.s.o. accordingly and work perfectly. So I calculate the GPIO pin number: G is 7th letter, 7 - 1 is 6, 6 * 32 is 192. GPIO192 exports fine, I can set it to output, change the value to 1 but there's no voltage! Can anyone help me, please?

Hello everyone! it is possible to make dual-boot between Armbian and a Android custom rom on Orange pi pc (h3)? I have only a sandisk extreme 64gb U3. I haven't other cards where to put Armbian and Android separated. Thanks in advance!

Hi, I receive 16 bytes every 0.5 seconds. This should be saved as text or as MySQL table data. Need to compare with all existing records , process and display it on 3.5 inch TFT LCD on SPI ( Notro fbtft ) and also save to SD Card . It should be broadcasted to a fixed Ip using TCPIP. Can I use Orange Pi Zero with 512MB Ram ? Can I partition Ram as RAMFS OR TMPFS to do all read only tasks thus save time for slow SD CARD writes ? Can I first copy boot files and my app,tables to Ram and start from Ram ? Any suggestions ? Thanks

Hi, I used to run a RPi3 as a VPN and DNS-Server (PiHole) and it worked like a charm. Since the RPI3 is a bit oversized for this work I bought a NanoPi Neo 512MB and installed armbian Ubuntu 4.9.x, but I have some issues with it: - eth0 is only connected by 100/half duplex. I can set it manually to full duplex with autoneg off, but after a few secondes it falls back to 10(!) half duplex. with autoneg on it comes back to 100 half duplex (the amber led is off; cable and switch are ok) - the MAC-Adress is changing every reboot. I have to fix it manually - I can set up Pihole to use the Nanopi as a DNS-Server and it works well in the LAN, until I connect over openVP…

I have a windows 7 laptop and the A20 cubietruck board with Mainline 4.9.7 Debian Jessie and I need to achieve an ssh connection between them via a wireless router.On cubietruck I have installed opnssh-client and openssh-server and have checked that it listens to port 22. On windows I try with putty to connect to board via ssh. The connection is done , I give username and password but then it freezes and I cannot access any of the folders of the debian. I also tried the mobaxterm but the same result. Does anyone has an idea of what I have done wrong?

Haaaa no one understand what i doing... Product i have : - Orange Pi Zero H2+ x2 - Orange Pi Pc Plus H3 First Orange Pi Zero H2+ i received is dead (boot but nothing) Second Orange Pi Zero H2+ boot but problem to access via network on debian jessie problem with ethernet driver i guess I'v surrender the Orange Pi Zero and i'v buy the Orange Pi Pc Plus H3 with EMMC, i have downloaded the last image of debian jessie on armbian for my Orange Pi Pc Plus H3 Orange Pi Pc Plus H3 boot everything ok with lastest debian version of debian jessie exept ETHERNET so i'v try to build my own rom with the armbia…

I recently rebooted my Cubietruck after a longer time because the WiFi daemon didn't work properly anymore. After the reboot, however, the system didn't boot from NAND anymore. I attached a serial console and got the following kernel panic (the full serial log is attached): <0>Kernel panic - not syncing: No init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance. [ 12.867986] Kernel panic - not syncing: No init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance. [<c001538c>] (unwind_backtrace+0x0/0x12c) from [<c0714d54>] (panic+0x9c/0x1cc) [ 12.887857] [<…

I was wondering if I could have automount feature for every UFD or USB Hard Drives to the /media folder. As i've investigated it, it would only mount if I get to click its icon on the desktop. I'm running bananapi as my headless file/media/print server. I shared the /media folder to the network through samba and was kept wondering why I'm unable to access every flash and hard drive I'm connecting to my bananapi as it does in my Raspberry Pi (when I share its /media folder in samba). Is there anything that I could do instead of adding it to fstab and manually restarting or manually mounting it every time I connect a media to my Banana Pi server? …

Hi I have an ARM-based board(http://wiki.friendlyarm.com/wiki/index.php/NanoPi_M1) and use Armbian(Ubuntu-server 16.04) on it. I have a 2.2" TFT-LCD with SPI connection, and use this framebuffer driver(https://github.com/notro/fbtft) to launch it. I can setup my LCD with this command: sudo modprobe fbtft_device custom name=fb_ili9341 gpios=reset:1,dc:201,led:6 speed=16000000 rotate=90 bgr=1 And before, when I had Ubuntu desktop, I could change display by this command: FRAMEBUFFER=/dev/fb8 startx But in Ubuntu-server I get this error message: X.Org X Server 1.18.4 Release Date: 2016-07-19 X Protocol Version 11, Revision 0 Buil…

The Luma library allows you to display text, graphics, animation, etc. on multiple display types. Here I will describe the easiest one to configure which is Luma.OLED and the I2C version of the SSD1306. You can find these displays on EBay and Amazon for less than $10 US each (you can get them for less than $3 US if you order from China, but it might not show up). I've configured Luma on many SBCs and it's my go to library if I need a small display for projects. Requirements NanoPi Duo (I used V1.0 board with 512 MB RAM) flashed with Armbian image. This will work with or without the mini shield. Small nylon nuts, bolts and standoffs if y…

Hello. this is my first post. I was looking through the forum but I did not find a similar problem. About power supply - until now I did not have any problems, I use a computer power supply. After a few months of non-use of my device, I downloaded an updated, latest version (Armbian_5.38_Lime2_Ubuntu_xenial_default_3.4.113_desktop) to an old, previously functioning card. When I connected the device, it did not turn on. I tried to turn it on manually, but nothing happened except the short flash on the connected mouse. A while ago, I uploaded an older desktop version to NAND. I used the sd card to start up. Is it possible that this older version loaded on NAND c…

I am trying to install my newly bought D-Link DWA-131 E1 on my Orange Pi PC with theLinux orangepipc 4.14.18-sunxi #24 SMP Fri Feb 9 16:24:32 CET 2018 armv7l GNU/Linux. I googled from the internet and there are so many guides which will not work for me. I almost messed up my OS and the installation still failed. I already re-flash the microSD card with a new "Linux orangepipc 4.14.18-sunxi #24 SMP Fri Feb 9 16:24:32 CET 2018 armv7l GNU/Linux". I am here looking for help if some one experts here can guide me through out the installation. I really appreciated for your help and thank you in advance. Best regards, …

Hi all, I noticed that my OrangePi freezes after 4-5 days of uptime. Something happens (usually around 06:00) when my script simply stop working (no more log entries) and then reboots after ~12 hours (exactly at 13:17 in all occasions). Finally the orange pi becomes unresponsive and heats up to 85-90 degree Celsius. I've checked CPU temperature, disk and memory usage but haven't found anything... I'm a beginner in armbian and completely having no idea what could be the root casue. Could you please help? I've executed a diagnostics you can find it here: http://ix.io/1iQc Related syslog entries: Jul 31 06:10:01…

Hello, Has anyone tried to bring up a SIM7100E based hat on Orange PI Zero over the UART GPIO interface? I have enabled the UART ports in armbianEnv.txt as follows: overlay_prefix=sun8i-h3 overlays=usbhost2 usbhost3 uart1 uart2 dmesg | grep tty shows : [ 0.000379] console [tty1] enabled [ 1.765329] console [ttyS0] disabled [ 1.785581] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 39, base_baud = 1500000) is a U6_16550A [ 1.785700] console [ttyS0] enabled [ 1.810679] 1c28400.serial: ttyS1 at MMIO 0x1c28400 (irq = 40, base_baud = 1500000) is a U6_16550A [ 1.835564] 1c28800.serial: ttyS2 at MMIO 0x1c28800 (irq = 41, base_baud …

I'm running an updated armbian stretch mainline on a nanopi neo and hitting a wall where I thought there would be no obstacles in my path. I'm using 433Mhx Tx and Rx devices so I'm building WiringNP (from FriendlyArm) and rfoutlet (from github.com/timleland/rfoutlet.git). I'm getting errors such as wiringPi ISR: Not implemented when running RFSniffer. [This is the current error, it's been one after another]. My mind is muddled at the moment since I've done this kind of thing several times in the past on other devices including the Orange Pi Zero. Can someone tell me if this is me, or if it's a NanoPi Neo-thing? Shouldn't this be straight-forwa…

Hi, I have trouble getting an IR receiver on the Orange Pi Zero+ to work. IR-Hardware: Orange Pi Zero Interface Board v 1.2 https://www.aliexpress.com/store/product/New-Orange-Pi-Zreo-Expansion-board-Interface-board-Development-board-beyond-Raspberry-Pi/1553371_32770665186.html I use Armbian 5.65 (Debian stretch), Kernel 4.14.78 I activate the IR receiver by adding "cir" to overlays in /boot/armbianEnv.txt On boot it is activated and the sunxi_cir module is loaded (and also lirc_dev, don't know why), see dmesg output: [ 5.245866] lirc_dev: IR Remote Control driver registered, major 244 [ 5.255140] IR LIRC bridge handler i…

Hey guys, I have a OP3 H6 and I cannot seem to find out why the 4 x USB ports are not working only the single USB next to the HDMI works. Any Ideas? Cheers!

Hi, I've installed armbian for Orange Pi 3 (Buster) Everything works great, and the system boots, I even copied to the EMMC for booting from the Flash. The only problem is that the status LED stays "RED" and doesn't turn "GREEN" right after booting, like it does in the orangePi official debian. How can I make it GREEN? Thanks Leon

Hi, I want to use g_ether on NanoPi Neo Plus2. For Neo Air, I have already figured out how to do this and I can see usb0 in config. But with armbian 5.85 (4.19.38-sunxi64), the same instructions fail at sudo ifconfig usb0 up with the message "usb0: ERROR while getting interface flags: No such device". Could somebody tell me how to activate USB OTG on NanoPi Neo Plus2 and then use g_ether. I think the same holds true for g_serial. This could be an alternative, but I would prever ethernet connection. My target: Connect NanoPi Neo Plus2 with NanoPi Neo Air via Ethernet Thank you for your help! Steps I followed for g_ether:

Hi, I'm having some instability issues with WiFi driver on Orange Pi Zero Plus, it uses RTL8189FTV instead of buggy XR819 chip. Some times it just works fine, but that's not always the case, some times when I turn on the board the driver is not able to turn on the WiFi chip, and it keeps stuck in a limbo state... The kernel identify the network device as (wlan0), but it's impossible to turn on or connect to any network. sudo dmesg | grep -Ei '(8192eu|rtl|wl|realtek)' [ 236.057560] RTL871X: Failed to init Power On! [ 236.057567] RTL871X: rtw_hal_init: hal__init fail [ 236.057573] RTL871X: -ips_netdrv_open - drv_open failure, bup=1 [ 236.057579] RTL8…

Hi, I have a Bananapi M1 running long Time with Debian Jessie. Now I installed Armbian Buster and always when I activate GPIO Pins my Network is gone on the integrated Card. Also GPIO is not working because of the Network Card. I tried to deactivate the Network Card and use an external WirelessLAN Card but the internal Card is still blocking my GPIO's. On Jessie and Wheezy before that was working perfect. Any advise? BR Peter

Hi I have installed the latest image for Orange Pi Zero v1 https://dl.armbian.com/orangepizero/archive/Armbian_24.2.1_Orangepizero_bookworm_current_6.6.20.img.xz link from https://www.armbian.com/orange-pi-zero/ After the first boot, I see that it is kernel 6.6.20 Welcome to Armbian 24.2.1 Bookworm with Linux 6.6.20-current-sunxi Linux version 6.6.20-current-sunxi (armbian@next) (arm-linux-gnueabihf-gcc (Ubuntu 11.4.0-1ubuntu1~22.04) 11.4.0, GNU ld (GNU Binutils for Ubuntu) 2.38) #1 SMP Sat Mar 2 17:23:09 UTC 2024 and when I run apt update& apt upgrade apt list --upgradable Listing... Done armbian-fir…

Hello, In additional items of v4.1, auto system update via repository apt.armbian.com You have written and has been added, if you have upgraded from v4.0, source.list of apt does not seem to have been updated. If the contents to be updated would be what kind of configuration information? I want you to tell me. Environment: -Debian jessie 4.1.4 -Cubietruck Best regards.

Hello. Thank you for your great effort. I'm using CubieTruck, and I installed Debian Jessie(Armbian, of course), and make it boot from Nand. It was successful. However, if I insert sd card into the slot, CubieTruck won't boot. Isn't it possible to boot from nand while sd card is inserted? I want mount the SD card to /home directory. (Using USB slot works.) Thanks in advance!

Please help me to install printer to my OPI PC i use Armbian_5.05_Orangepih3_Debian_jessie_3.4.110_desktop.zip OPI sees the printer in usb but because of my low level of knowledge i only use tools in x desktop (windows like) , so i couldnt find any on desktop The main aim is to setup printer and make it sharable in wireless network (wlan is ok) so please help me to setup my printer step by step i d really appreciate it if you help

Just FYI: Orange Pi Plus 2E is now available for $35 and shipping costs remain the same (pretty low compared to some competitors): http://aliexpress.com/store/product/Orange-Pi-Plus-2-E-H3-Quad-Core-1-6GHZ-2GB-RAM-4K-Open-source-development/1553371_32665196281.html Please remember that this board was designed based on community requests (dropping the slow GL830 USB-to-SATA bridge and the internal USB hub and exposing all 4 USB ports physically to the outside) and should make up for a really nice server with 2 GB DRAM, Gbit Ethernet and 4 USB ports (3 real hosts ports and one Micro OTG). So now we have the following H3 boards with Gigabit Ethernet: Banana …

Hello, I use the desktop version of Legacy with my Cubietruck. My problem is that I can’t launch Kodi. I installed it with 'sudo apt-get install kodi' but If I start the program I have a black screen and then kodi is closed. I reinstalled Kodi and updated the system. But the problem was not solve. Have anyone an idea how I can solve this problem?

Dear Sirs and Madams! I am trying to reconfigure https://github.com/friendlyarm/h3_lichee BSP's kernel via make menuconfig which is producing following .config file: # # Automatically generated file; DO NOT EDIT. # Linux/arm 3.4.39 Kernel Configuration # CONFIG_ARM=y CONFIG_ARM_HAS_SG_CHAIN=y CONFIG_SYS_SUPPORTS_APM_EMULATION=y CONFIG_GENERIC_GPIO=y # CONFIG_ARCH_USES_GETTIMEOFFSET is not set CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y CONFIG_KTIME_SCALAR=y CONFIG_HAVE_PROC_CPU=y CONFIG_STACKTRACE_SUPPORT=y CONFIG_LOCKDEP_SUPPORT=y CONFIG_TRACE_IRQFLAGS_SUPPORT=y CONFIG_HARDIRQS_SW_RESEND=y CONFIG_GENERIC_IRQ_PROBE=y CONFIG_GE…

Hi I want to use SPI0 with cubietruck. SPI2 works. However I failed with SPI0. What needs to be done (in script.fex, kernel, etc) to get it work?

Hello everyone, I've recently bought an OrangePI PC Plus with an intentions to make it (beside others) a multimedia center. Because of community and pretty good status of armbian on h3, I've downloaded and installed (a.k.a copied to sd) the latest armbian I found (5.20 with kernel 3.4.112). Everything went ok, I've got graphical desktop, hw accelerated h264 and h265 over hdmi to my tv. So the next step was to install kodi. An that's the point where my troubles started. After I installed kodi and probably updated the whole armbian (apt update && apt upgrade && apt dist-upgrade), I noticed that my TV turns off almost immediately I turn it on to h…

So I have a question... I'd like to manage Li-Ion battery operation on SBCs using the AXP209 power management chip (especially the Banana Pro, as that's what I have...) I soldered a connector to the battery terminals on my BPro for portable operation, and it would be nice to have some kind of solution to raise an alert at low battery charge (like via the onboard LEDs), and automatically call system shutdown at a certain level. Googling has shown that the AXP209 has an i2c interface for sensors, and there are a few scripts for reading battery status here: http://hardware-libre.fr/2014/11/banana-pi-axp209-battery-power-monitoring/ My current plan is to pro…

After trying the ESP32, CHIP and CHIP PRO, I now have the OPI Zero+2 H5 and after much research (the Armbian forums) and testing, was unable to get USB OTG and Bluetooth working. I'm particularly interested in Bluetooth Low Energy and WIFI. WIFI worked great, simply using nmtui, worked first time. Thanks for solving the AP6212A WIFI firmware issues. However, do I understand correctly the USB OTG (I want to connect the OPI Z+2H5 micro USB to a USB hub to connect a mouse and keyboard) is not working yet? Similarly, is the AP6212A bluetooth driver/firmware being worked on at the moment? In addition, I'm waiting for some cameras to be delivered, my next project being the CSI …

Hi, my environment is: Orange Pi One ARMBIAN 5.34.171031 nightly Ubuntu 16.04.3 LTS 4.11.12-sun8i WiringPi fork by WereCatf: git clone https://github.com/WereCatf/WiringOP.git -b h3 ./build small c++ programm: #include <stdio.h> #include <string.h> #include <errno.h> #include <stdlib.h> #include <wiringPi.h> #include <pthread.h> static volatile int globalCounter; void myInterrupt(void) { ++globalCounter; printf("InterruptCounter: %5d\n", globalCounter); //digitalRead(7); } int main(void) { if (wiringPiSetup() == -1) { print…

IPv6 is not working correctly for me although my connection information seems right, I am not able to ping6 to google.com for example. IPv4 is working fine. Is this a known bug? Or does anybody know a solution to this problem? In the pictures below you can see what error I'm getting and also my connection information.

How to use an Orange Pi Zero Plus as an ethernet gadget over usb otg using g_ether?

Hi all, I have an application running on an orange pi pc plus 2 over the emmc 8gb memory. Everything is in there (os, db sw) and what it does is acquiring data from some sensors and then pushing it over mqtt to a server. Now, due to frequent internet connection issues, the board is able to store up to ~ 1 month of data in a local db but this means quite a lot of writes per seconds (plus all the logs). I would like to have an idea of how much the emmc can keep up with this rates and thus I am trying to understand how to calculate the life span in years (hopefully nothing less). Can anyone help me on how to do that? I am using right …

Hello all. Okay: I am a total newbie to Orange Pi. I apologize upfront for any and all obvious self inflicted mistakes that you all spot. AGAIN: total newbie to the Orange Pi world. Please go easy in me! I have an Orange Pi Win Plus A64 board and frankly --- I love the darn thing! Powerful for my needs and I have a niche application that I am working on and this board is really the only one that fits my needs. The 2GB RAM is a must. The issue I am having is this: I am usinga waveshare 10.1 inch TFT HDMI display that has the SPI connector (lcd: https://www.waveshare.com/wiki/10.1inch_HDMI_LCD). I have att…

I started compiling some project (snowboy ) on the nanopiDuo2 like I am doing on the FriendlyCore 16.04 and suddenly the board stop working/booting. The red led is blinking fast, the same sd card is working on different boards, FriendlyCore does not boot on this board. "provide a log from serial console" I don't have serial cable yet. This happened to me twice, on Armbian 18.04 and on 20.04. First it destroyed the "IoT-2G Application Carrier Board for NanoPi Duo2" that it was on without the board, and the carrier had burnt smell, internet cable and power were connected. For one of them the red led is blinking fast, for the other the led do…

The module ds2490 seem to be missing in the new release. Should be: /lib/modules/4.19.62-sunxi/kernel/drivers/w1/slaves/w1_ds2490.ko

After updating to 5.9.14 from 5.8.16, framebuffer is broken. No output after booting, hdmi monitor goes to sleep. [ 1.455763] ------------[ cut here ]------------ [ 1.455791] WARNING: CPU: 0 PID: 1 at arch/arm/mm/ioremap.c:287 __arm_ioremap_pfn_caller+0x13f/0x14c [ 1.455796] Modules linked in: [ 1.455810] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.9.14-sunxi #20.11.3 [ 1.455814] Hardware name: Allwinner sun7i (A20) Family [ 1.455846] [<c010cce9>] (unwind_backtrace) from [<c010945d>] (show_stack+0x11/0x14) [ 1.455862] [<c010945d>] (show_stack) from [<c093b0ab>] (dump_stack+0x77/0x84) [ 1.455878] [<c093b0ab>]…

Hi there! I just received three decommissioned BananaPI M1+ from a company and I'm trying to install the latest version of Armbian Buster available on them. Once I flash the image to the SD card (tested and working fine), however, the board goes into boot loop as per the video. The only error that seems to be displayed is "EHCI failed to shut down host controller". If it can be useful to find the cause, I point out that the problem occurs with both Armbian Buster and Armbian Focal regardless of the presence of the "fdtfile=sun7i-a20-bananapi-m1-plus.dtb" line in the /boot/armbianEnv.txt file. What do you think I could do to solve it? Thank you all in advance.

Hello everyone! Yesterday I downloaded "Armbian 23.5 Jammy". Unfortunately the integrated wifi module does not work. I tried several alternatives but with the same problem. I am not an expert on the subject. Any solution? I'm trying to compile and in one of the steps it tells me that the "Orange Pi 3 LTS - H6" is no longer supported. If anyone knows and can help would be appreciated. https://paste.armbian.com/varepekose Original: Hola a todos! En el dia de ayer descargue "Armbian 23.5 Jammy". Lamentablemente no funciona el modulo wifi integrado. Probe con varias alternativas pero con el mismo problema. …

Hello fellow Sunxi forum members, Some may know me from previous Armbian adventures, primarily Orange Pi Zero 3... but I have jumped brands for a change of scenery (but not SoC). When researching H61X based boards for the Zero 2 and Zero 3 development we were doing in another thread, I found the Sipeed LonganPi 3H, which is a relatively new board that took a while to find. My first impressions are that is really well made, and packs a lot in to the Raspberry Pi Zero style profile (although it also has a daughter board). It was shipped quickly in a nice quality hard plastic storage case and.. best of all.. it has two hardware buttons.. so I can rese…

Hello! I have installed image Armbian_24.2.1_Orangepizero_jammy_current_6.6.20_minimal.img from https://www.armbian.com/orange-pi-zero/ Orange Pi Zero H2+ 256M There are only utils root@mobi:~# armbian armbian-add-overlay armbian-install armbianmonitor https://paste.armbian.com/ayoxebogog

the tft is working well on stock orangepi image but when I try the prebuilt armbian images or build it myself it look like this my dts file: 35Lcd.dts

the nand-sata-install always proposes the sda1 as a destination. this did not fit what i needed. i have had success by editing the file and replace all sda1 with sdxx (whatever i need) and then it works (the information gives the wrong size in the initial screen). i looked into the code (but i do not understand bash programming): it seems that sda1 is hardwired despite the intention to find all possible destinations and to offer them. it is a useful utility, as it does several things at once (copy stuff, change fstab) which are otherwise separate coordinated steps. thank you for the utily! andrew install into nand did the correct copying, but did not …

Hello I want enable smb 2.1 on cubi plese help step by step and make error: root@cubietruck:/usr/src/linux-headers-4.2.3-sunxi# make scripts/kconfig/conf --silentoldconfig Kconfig CHK include/config/kernel.release CHK include/generated/uapi/linux/version.h CHK include/generated/utsrelease.h make[1]: *** No rule to make target 'arch/arm/tools/gen-mach-types', needed by 'include/generated/mach-types.h'. Stop. arch/arm/Makefile:305: recipe for target 'archprepare' failed make: *** [archprepare] Error 2 please help with step by step. Gabor Sneff

Hallo, I have got the Banana Pi (no Pro) with Armbian Trusty Desktop and Legacy Kernel 3.4.109 installed. All updates done. Problem: No Sound on HDMI Output. Any suggestions? Known Problem? bewoco

So can you guys help me debug, why I can't get the microphone to work on my Orange pi pc. Speaker works just fine. Arecord records nothing, silent file . Here is some terminal output: msev@orangepipc:~$ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: audiocodec [audiocodec], device 0: SUNXI-CODEC sndcodec-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: sndhdmi [sndhdmi], device 0: SUNXI-HDMIAUDIO sndhdmi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 msev@orangepipc:~$ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: audiocodec [audiocodec], device 0: SUNXI-CODEC sndcodec-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 car…

Hi, is one of your images able to play movies and watch youtube?

Hello, I installed Armbian/(debian jessie) on my Orange Pi Plus (EMMC). Works good, but i can't find the temp of the processor. (lm-sensors don't work/can't detect sensors) What should i do?

Hey guys, I was wondering why the Browsers doesnt support H/W Acceleration, now i found out its because the Mali Driver is outdated. I installed also Chromium and forced it to use the GPU, well at least it trys but i got a bunch of errors. Is there a way to add a new Driver? Tried also to compile it myself but i was never that deep into linux and never had to compile drivers, here are the sources: http://malideveloper.arm.com/resources/drivers/open-source-mali-utgard-gpu-linux-kernel-drivers/ I think the current Kernel uses a horrible outdated r3p0 Version and a new one is r7p0, at least r4p0 is needed which should work with Chromium and finally add H/W Accelerat…

Hi there # uname -a Linux orangepipc 3.4.113-sun8i #28 SMP PREEMPT Thu Feb 2 02:01:28 CET 2017 armv7l GNU/Linux #apt-get install pciutils-dev pkg-config #git clone https://github.com/flashrom/flashrom.git #cd flashrom #make CONFIG_INTERNAL=no CONFIG_RAYER_SPI=no CONFIG_NIC3COM=no CONFIG_GFXNVIDIA=no CONFIG_SATASII=no \ CONFIG_ATAHPT=no CONFIG_DRKAISER=no CONFIG_NICREALTEK=no CONFIG_NICNATSEMI=no \ CONFIG_NICINTEL=no CONFIG_NICINTEL_SPI=no CONFIG_OGP_SPI=no CONFIG_SATAMV=no No work! hooked: spi_mosi = port:PC00 spi_miso = port:PC01 spi_sclk = port:PC02 spi_cs0 = port:PC03 root@orangepipc:~/flashrom# ./flashrom -p linux_spi:dev=/dev/spidev0.0 flashrom v0…

Hi, I tried to safe-upgrade (apt-get upgrade) Trusty today but got the following notice: Failed to fetch http://apt.armbian.com/dists/trusty/main/binary-armhf/Packages It would be OK to dist-upgrade to Xenial anyway as described in the Docs ... apt-get install update-manager-core do-release-upgrade -d # further to xenial apt-get dist-upgrade ... but I think it would be a good idea to start from a proper Trusty. Any suggestions. Thanks in advance Mark

I looks like there are more as one way to setup kodi on orange pipc. The latest version 17.1 of kodi with hardware exsaleration would be preferable. I wanted a setup where i could use the on board ir and some Remote i already own. Then an usb Keyboard. And i did not want that kodi starts at system start. I also wanted VNC be usable to do a login via VNC to be able to remote control from my Leptop. I did get Kodi 15.2 working but with drawbacks: Video is not smooth, not relay nice to view. VNC and IR did work and i could go back to the desktop to start internet browser or something else, all rather slow. Colors of the HDMI TV look …

Has anyone been able to successfully install rpimonitor on an Orange Pi Win Plus (A64)? I have been able to install it, but I get a lot of invalid readings. As you can see in the screenshot, it is not able to detect cpu frequency, vcore and temperature.

Hi, I have a problem while taping the following command : root@orangepizeroplus2:~# cat /dev/ttyS2 cat: /dev/ttyS2: Input/output error root@orangepizeroplus2:~# cat /dev/ttyS1 cat: /dev/ttyS1: Input/output error root@orangepizeroplus2:~# cat /dev/ttyS3 cat: /dev/ttyS3: Input/output error root@orangepizeroplus2:~# cat /dev/ttyS0 ^C root@orangepizeroplus2:~# Is there a way to activate those devices? (I know that we can enable them using "script.fex" file with OP H3 but I don't know how to do it with mainline kernel H5) Please check the boot logs of the board here : http://sprunge.us/dCLS Please any help would be appreciated !!

mt7601u wifi dongle not working on my cubieboard, i have compiled driver, run make, make install and modprove, everything successful, but iwconfig not showing ra0, and when i run ifup ra0 it shows device not found. $ lsusb Bus 001 Device 005: ID 148f:7601 Ralink Technology, Corp.

root@orangepizero:/boot# iptables -nL modprobe: ERROR: ../libkmod/libkmod.c:586 kmod_search_moddep() could not open moddep file '/lib/modules/4.14.14-sunxi/modules.dep.bin' modprobe: FATAL: Module ip_tables not found in directory /lib/modules/4.14.14-sunxi iptables v1.6.0: can't initialize iptables table `filter': Table does not exist (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. root@orangepizero:/boot# uname -a Linux orangepizero 4.14.14-sunxi #1 SMP Thu Jan 25 12:20:57 CET 2018 armv7l armv7l armv7l GNU/Linux root@orangepizero:/boot# Can someone help me how to fix this issue on Orange Pi Zero - 512 MB board ? I am running Armb…

Hello ! I know that there are already topic talking about that, but they didn't helped me. I have Armbian 5.38 Desktop. I plugged the camera, and I think it's on the right side: I followed instruction of Garlic here: Nevertheless, with motion I get a grey screen telling me that the camera is undetected: I noticed a very small impact on the cable after the delivery of the camera, but because it is very small, I don't think it's the cause. I don't understand, and any help is welcome. Thank you !

Cubieboard2 becomes unreachable on ethernet if the switch to which the CB2 connected to is rebooted/powered off then on. Every other devices communicate after the restart, except CB2, it needs an on/off to make its networking work again. Why? It has fixed IP, and also set fixed mac address, but no luck. It runs the latest armbian (5.38), with mainline kernel

Hello Everyone! Need your help to difficult task. I'm a newbie to micro-computers. Recently installed Armbian on Orange Pi PC Plus (H3), but can't connect to a TVusing HDMI-VGA adapter. Get just black screen, but once got a pink image (as in attachment). That HDMI-VGA adapter works well with notebook and shows picture on this TV. However, this adapter works well with Orange Pi and my Iiyama computer monitor in VGA mode. So, i completely dont understand why Orange Pi not working especially with my Sharp TV. Native resolution of TV is WXGA (1360x768). I tried many resolutions and got black screens, but in XGA (1024x768) resolut…

Hi All! OS - ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.18-sunxi OPI Zero. armbianEnv.txt : overlay_prefix=sun8i-h3 overlays=uart2 param_uart2_rtscts=1 RTS CTS don't work I check the work of the logical analyzer. The line RTS does not change the voltage during the request for data transmission. This is necessary for me to connect the MAX485 chip to UART2 OPI Zero.

I know I'm supposed to log with armbianmonitor -u, but I can't behind that ***** corporate proxy. So I made a strace. / _ \ _ __ __ _ _ __ __ _ ___ | _ \(_) |__ /___ _ __ ___ | | | | '__/ _` | '_ \ / _` |/ _ \ | |_) | | / // _ \ '__/ _ \ | |_| | | | (_| | | | | (_| | __/ | __/| | / /| __/ | | (_) | \___/|_| \__,_|_| |_|\__, |\___| |_| |_| /____\___|_| \___/ |___/ Welcome to ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.18-sunxi System load: 0.11 0.24 0.25 Up time: 6:55 hours Memory usage: 26 % of 493MB Swap usage: 9 % of 127Mb IP: 10.aa.bb.ccc 169.254.6.65 CPU temp: 45°C Usage …

4.14.65-sunxi on an Orange Pi Zero. Trying to set the i2c bus speed to 400kHz using the following dts: /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { target = <&i2c0>; __overlay__ { clock-frequency = <400000>; }; }; }; Which produces: Error: dtc does not support compiling overlays Please try to install matching kernel headers Installed linux-headers-next-sunxi and still getting the same thing. Device tree compiler version: DTC 1.4.2. What am I doing wrong? Spoiler

no led, no output, tried it with 3 different 16gb class 10 sandisk sd cards, previous versions works fine, and i also tried the download from torrents and the direct downloads, still nothing

I cannot use my dmesg in a normal way anymore. It is flooded by these messages: [ 2828.613264] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x48, dev addr: 0x48) [ 2828.613724] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x48) [ 2828.613906] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x48, dev addr: 0x48) [ 2828.614101] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x48, dev addr: 0x48) [ 2828.614485] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x48) [ 2828.614660] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x48, dev addr: 0x48) [ 2828.61483…

Hello, it is been awhile since I used armbian with Orange PI, now I took one orange PI NEO on it's connector is UART0, UART1 and UART2. My goal is to use all UARTS available on board. Googling a little I found the part where I should use BIX2FEX to convert script.bin and insert port definitions there, bot looks like that way is obsolete. looks by default only one uart is initialized: root@nanopineo:/boot# cat /proc/tty/driver/serial serinfo:1.0 driver revision: 0: uart:16550A mmio:0x01C28000 irq:49 tx:11630 rx:0 RTS|DTR 1: uart:unknown port:00000000 irq:0 2: uart:unknown port:00000000 irq:0 3: uart:unknown port:00000000 irq:0 4: uart:unknow…

Hi all, First post here. I have been running Armbian on my original Bananapi Pro for a long while now, and thought that it's time to upgrade from Bullseye to Bookworm finally. There were some complications with UsrMerge that I had to resolve manually (I think some boot files from the original Buster installation were both in /lib and /usr/lib), but apart from that the upgrade appears to have worked: All userspace stuff is on Bookworm. # lsb_release -a No LSB modules are available. Distributor ID: Debian Description: Armbian 24.5.0-trunk.530 bookworm Release: 12 Codename: bookworm However, the kernel seems to be stuck on 5.15…

Hi I'm trying to understand how to enable Uart 2 for serial communication with a mcu on the banana pi (trying to connect a board running klipper to it). I connected the Uart of the board to CON1-P08 and CON1-P10 of the Banana PI M3 according to all i can find those pins are tx/rx for UART2. So far i figured out that the UART should be one of the /dev/ttyS* ones if i'm not mistaken, I can see /dev/ttyS to /dev/ttyS7 but am missing the /dev/ttyS1 user@bananapim3:~$ ls /dev/tty* /dev/tty /dev/tty11 /dev/tty15 /dev/tty19 /dev/tty22 /dev/tty26 /dev/tty3 /dev/tty33 /dev/tty37 /dev/tty40 /dev/tty44 /dev/tty48 /dev/tty51 …

During installation new Image show on screen following problems: Failed to retrieve unit state: Transport endpoint is not connected _ _ _ _ _ /_\ _ _ _ __ | |__(_)__ _ _ _ __ ___ _ __ _ __ _ _ _ _ (_) |_ _ _ / _ \| '_| ' \| '_ \ / _` | ' \ / _/ _ \ ' \| ' \ || | ' \| | _| || | /_/ \_\_| |_|_|_|_.__/_\__,_|_||_|_\__\___/_|_|_|_|_|_\_,_|_||_|_|\__|\_, | |___| |__/ v26.2 rolling for Orange Pi Zero running Armbian Linux 6.12.63-current-sunxi Packages: Debian stable (trixie) Support: …

Hey guys, my cubietruck doesn'T recognize my usb keyboard at all, while he is booting. It is a logitech mk300 wireless keyboard. with aruntu and other stuff it worked without a problem. The keyboard works, i am writing this text with it. When cubie boots, it checks the usb devices and sais unable to get device descriptor. Is this a known bug? I have no other keyboard, so cubie is useless for me... I have tried different images and versions, allways the same error...

Hi ! Ref : Olinuxino LIME2 4G with new 3.4.112 kernel When installing to NAND, on the console I see a lot of : PHY_PageRead : too much ecc err,bank 0 block 276,page 4 PHY_PageRead : too much ecc err,bank 0 block 276,page 18 and so on ... Sometimes the installation succeeded, sometimes not, but the system is often instable, and finally, fully unusable. I tried all the precompiled images, then I compiled myself, but the same problem ... Until now, I used 3.4.106 without problems Thanks for support ! Greetings ,

Hi everyone, I was doing speed tests on the XR819 and started looking at the driver code. My this looks very similar to the cw1200 driver already in mainline Linux. I started modifying the cw1200 driver to try and get it to work with the XR819. Apart from someone renaming functions and adding a bunch of important junk for XR819, the drivers are quite similar. I've modified the cw1200 driver up to the point that it's loading the boot_cw1x60.bin ( boot_xr819.bin ) file, but for some reason the bootloader is returning an error instead of success. I don't think it's possible to diagnose this without the datasheet from ST. Clearl…

I have problem with transmission-deamon on my CubieA20. It not starting listening on boot. Only after service restart. Met same problem on Raspberry-3 but it cured by enabling "boot to wait until a network connection is established" option. I checked the raspi-config and taken same measures on my A20 ("ExecStart=/sbin/dhcpcd -q -w" etc). Not succeeded! Anyone have alternate methods? There's some more applications that not starting on boot if connection not active, Blynk-client for ex. PS: I use legacy kernel on 5.25 Armbian. UPD: Problem resolved by editing /etc/network/interfaces.