Allwinner sunxi

Hello, I have an orangepi win plus and I installed "Armbian_5.90_orangepi_ubuntu_bionic_next_4.19.57_desktop". I'm using ttyS2 and ttyS3 ports and working well for serial ports. But bluetooth not working. Bluetooth icon is shown at right top on screen. When I clicked bluetooth on and click search new devices, system say to me "adapters not found." I tried, And too many options I can't remembered but I can't. How to devices bluetooth on? If you have more information, I will send you any information from terminal. Sorry for bad English. Thanks for help.

Hi, I was just wondering if anyone else out there with a Win+ has this issue .... when I install from an image file all works well, WIFI etc all good. But when I upgrade the install wlan0 etc has gone. ifconfig doesnt show it, lsmod shows the brcmfmac/cfg80211 I've tried it with a few of the recent image files systemctl status systemd-modules-load systemd-modules-load[1693]: Failed to find module 'lp' systemd-modules-load[1693]: Failed to find module 'ppdev' systemd-modules-load[1693]: Failed to find module 'parport_pc' root@zoot: lsmod Module Size Used by ipt_MASQUERADE …

I compiled an environment for an Orange Pi zero using CSC, Edge , Jammy, console server, standard. I didn't change any of the defaults. Things works except for the OrangePi expansion card with dual USB ports. The expansion card USB ports are not recognized. Anyone know what I need to select to get the expansion board working?

I'm running Armbian Bionic on OPizero. I have a problem using arecord on the mic input. Audio codecs have been enabled but when I run following command to record I get a pcm read error arecord -D plughw:0,0 -d5 -f cd test.wav Recording WAVE 'test.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo arecord: pcm_read:2103: read error: Input/output error There is no recording and file is just 44 bytes. pi@orangepizero:~$ ls -l test.wav -rw-r--r-- 1 pi pi 44 Jan 6 20:44 test.wav The output from this command never finishes after 3 seconds and I have to use ctrl+c to breakout: arecord -vvvv -d 3 /dev/nul…

Hello, I use Orange Pi Zero + 4 ports USB hub + CM108 USB-Audio cards with mic-in. All by default. Each mic is captured with sipmle commands like: arecord -v -r 44100 -c 1 -D "hw:CARD=Device_1,DEV=0" -f S16_LE > mic1.wav When 3 cards capturing simultaneous all working well. But if I start capturing with 4th card simultaneous I get two cards with crackling recorded audio. I even can see that arecord saves less data from these two cards (file size is less than with 3 cards). No error/warning provided anywhere (dmesg, syslog, arecord). Moreover, if I stops recording from one card - it becomes normal fo…

Hello. I have a small problem: I can't change the language on my OPi Zero. I have successfully done that with OPi Lite 2 and OPi 3, but for some reason on the Zero when I go to change it, the module fails to load and just quits back to the same "menu page". (essentially does nothing). The only thing I can think of, is that both of the other boards have 1Gb RAM and this only has 512Mb and thus it runs out of memory? That doesn't sound too plausible though - a list of keyboard languages shouldn't take tens or hundreds of megs of RAM. As far as I know, each board is running the same version of Armbian, so that shouldn't be a problem.

Hi all, With a fresh install of version 5.38 (jessie 4.14.15, idle since 5 min.), I've a CPU throttling and load issues : Spoiler root@OPZ2:~# armbianmonitor -m Stop monitoring using [ctrl]-[c] Time CPU load %cpu %sys %usr %nice %io %irq CPU C.St. 07:29:43: 1200MHz 1.11 23% 13% 8% 0% 1% 0% 44.5°C 0/8 07:29:48: 1200MHz 1.18 1% 0% 0% 0% 0% 0% 43.1°C 0/8 07:29:53: 1200MHz 1.15 0% 0% 0% 0% 0% 0% 43.0°C 0/8 07:29:58: 1200MHz 1.14 0% 0% 0% 0% 0% 0% 41.7°C 0/8 07:30:04: 1200MHz 1.13 0% 0% 0% 0% 0% 0% 41.6°C 0/8 07:30…

I'm having difficulty getting Octoprint to start. I've set it up in init.d and defaults. When I execute it directly I get an error about running as root. It's like it's ignoring the octoprint_user. /etc/default/octoprint: # Configuration for /etc/init.d/octoprint # The init.d script will only run if this variable non-empty. OCTOPRINT_USER=octoprint # base directory to use #BASEDIR=/home/octoprint/OctoPrint # configuration file to use #CONFIGFILE=/home/pi/.octoprint/config.yaml # On what port to run daemon, default is 5000 PORT=5000 # Path to the OctoPrint executable, you need to set this to match your installation! DAEMON=/home/octoprint/OctoPrint/…

Below is my attempt to compile the RealTek 8192cu driver for my ARMBIAN 5.31 stable Ubuntu 16.04.3 LTS 3.4.113-sun8i image running on my Orange Pi Zero. The BOLD area's below are the commands, I typed, everything else is exactly the way it came across on the console. Any help will be greatly appreciated. -0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0--0-0- root@orangepizero:~# apt-get install --reinstall linux-headers-$(uname -r) linux-headers-generic build-essential dkms git Reading package lists... Done Building dependency tree…

Orange Pi Zero shows error [FAILED] Failed to start Load Kernel Modules. See 'systemctl status systemd-modules-load.service' for details. More details How to fix this error?

Hello, I have been struggling for some time with random freezes. I am running application with i2c0 Fram and UART1 for transferring/receiving data based on MAX3232. The freezes cause no response from Orange PI (debug UART too), only unplug power helps. I read that it may be a problem with powering but i tried many USB power adapters 2A, 3A and ATX power (28A) connected to GND and 5v, nothing helps. I have lowered cpu max frequency to 816Mhz and still the same. All necessary data uploaded via armbianmonitor.

Hi there. I use Orange Pi zero as home print server. It works for few months for now and I am very pleased with that. Although, my printer falls into deep sleep after printing (it's Brother HL-1110EW) and cannot be woken up by the server. I have to start printer manually to print next printouts. Thus I wanted to install tea4cups to drive a relay turning the printer on and off when needed. I installed the WiringOP-zero (from here: https://github.com/xpertsavenue/WiringOP-Zero) but then strange things become to happen. I connected temporarily a LED diode to indicate the changes of the GPIO. (GPIO-7 and GND). The LED is on all the time, no matter what command I se…

I'm getting an error and I'd like some feedback if it is a missing package (apt-get) or a bug in OctoPrint or something wrong in Python. It looks like something is blowing up with Python trying to install a package called scandir 1.3, but I'm not getting anything when I google it with the error. Thoughts? The documentation on Git was up to date... the documentation on Octoprint.org is wrong for building it from source. Error: creating 'dist/OctoPrint-1.3.0-py2.7.egg' and adding 'build/bdist.linux-armv7l/egg' to it removing 'build/bdist.linux-armv7l/egg' (and everything under it) Processing OctoPrint-1.3.0-py2.7.egg creating /home/admin/OctoPrint/venv/li…

Hello, i'm trying to make a mesh network with some Orange PI Zero devices, but ibss (adhoc) and 80211s (mesh) seem not working...with an usb wifi work fine... I have read that this device's support isn't the best, but i don't kwnow if my case is a release specific bug or these modes aren't really supported. Installed release "Armbian_5.38_Orangepizero_Debian_stretch_next_4.14.14", i have also trying dev kernel but this don't load the device... What are the really working modes and valid interface combinations? Reported info by iw list command seem not correct. Thanks for the help

root@orangepizero:/boot# iptables -nL modprobe: ERROR: ../libkmod/libkmod.c:586 kmod_search_moddep() could not open moddep file '/lib/modules/4.14.14-sunxi/modules.dep.bin' modprobe: FATAL: Module ip_tables not found in directory /lib/modules/4.14.14-sunxi iptables v1.6.0: can't initialize iptables table `filter': Table does not exist (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. root@orangepizero:/boot# uname -a Linux orangepizero 4.14.14-sunxi #1 SMP Thu Jan 25 12:20:57 CET 2018 armv7l armv7l armv7l GNU/Linux root@orangepizero:/boot# Can someone help me how to fix this issue on Orange Pi Zero - 512 MB board ? I am running Armb…

All, Does anyone know how I can enable the OnBoard Wifi using Armbian? Is there a driver included for for the XR819 on-board WiFi module? any pointers would be much appreciated.... Thanks Gerry

Hi, is it possible to use the OTG as a mass storage device? Would it be possible to use an iso or harddrive image as "mass storage" device?

I am using fresh installation of armbian legacy server version 3.4.113 on the Orange Pi Zero Rev v1.1. The FEX file seems to be incorrect. Some driver or process is blocking PA10, which is wired directly to the expansion header pin 26. According to the schematics, this port is not used anywhere else. # cat /sys/kernel/debug/gpio GPIOs 0-383, platform/sunxi-pinctrl, sunxi-pinctrl: gpio-10 (? ) out hi gpio-17 (red_led ) out lo gpio-202 (xradio_irq ) in lo gpio-354 (? ) out hi gpio-362 (green_led ) out hi In case i am the first one that tested this: gpio-10 aka PA10 aka ? is blocked gpio-17 aka …

Just bumped this one: Orange Pi Zero, stable version, legacy kernel Trying to insert Realtek WiFi dongle (8188eu in my case). Module cannot load - with this error: Peeked solution on 4pda - http://4pda.ru/forum/lofiversion/index.php?t750921-1740.html - decompiled script bin and set wifi_usbc_id = 1 - before it was set to none. Original solution has value "2", but it was just a guess, so I used "1". Module worked in parallel with original xradio. According to original poster on 4pda, this issue was seen on Orange Pi PC. Not sure, is it correct solution, but, well - it may help. Issues seen - when I try to un…

Thanks for your effort on this project. Much appreciated. I was able to follow this tutorial (10 minutes, 24 seconds in) on the Debian image to get the TV out working. I'm building scripts to modify the networking between a number of modes - super helpful to get a console access when I break something and lose all networking access. Is there support for this on the Ubuntu side? The simple "add 'tv' to the bottom of "/etc/modules" doesn't do anything. Please advise. Thanks!

Hi, I am trying to use the two UARTS on the I/O pins which are UART 1 and UART 2 mapped to PG6/PG7 and PA0/PA1 respectively. I have had a look at the FEX file and these seem to be mapped correctly to UARTS's port 1 & 2 so I would expect these to be mapped to /dev/ttyS1 and /dev/ttyS2 but this does not seem to be the case. If I try to connect to these UARTs using screen I simply get the message: - root@orangepizero:~# screen /dev/ttyS1 9600 [screen is terminating] I have tried searching these forums and Google but have not really found anything - any help or pointers in the right direction would be much appreciated. Gerry

I have a wifi dongles that aren't showing up with the usual wlan0/1 identifier, below is what I've discovered so far, but if anyone can shed some light on this, I'd be much appreciative. ifconfig -a I get the following: wlx20e816006af8 Link encap:Ethernet HWaddr 20:e8:16:00:6a:f8 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 TX bytes:0 (0.0 if I do iwconfig wlx20e816006af8 essid myhomesid channel 6, I get no errors, however, when I do the iwco…

Hi all, its probably something simple but here is what i am struggling with: airmon-ng start <interface name> iwconfig wlan1mon channel 13 aireplay-ng --test wlan1mon ifconfig wlan0 up -> wlan0 is configured and connected to the access point packets are injected and can be observed with another machine ifconfig wlan0 down / or not associated with network packets are not injected and cannot be observed aireplay-ng or raw socket directly shows no errors initial toughs somewhere there is a switch to enable/disable radio at low level nothing obvious in strace tried with and without network manager…

Hello, I have 2 Orange Pi Zero boards, one with 256MB RAM and one with 512MB RAM. I tried running both: Armbian_5.25_Orangepizero_Ubuntu_xenial_default_3.4.113.img and Armbian_5.24.170110_Orangepizero_Ubuntu_xenial_4.9.0.img, but the same thing happens. When I power on the OPZ, a few seconds later the Red LED starts blinking and doesn't stop... The issue is present on both boards. Any suggestions?

Hello, My Orange Pi Zero was working during a few days. However after a few days it stopped working. I tried to install a fresh armbian (and I also tried lot's of different distribution on several SD cards), and all of them are unable to boot. Today, I tried to plug an UART cable (USB <-> Serial) during boot in order to see what happened... And here is what I got : U-Boot SPL 2016.09.01-armbian (Nov 14 2016 - 08:40:41) DRAM: 0 MiB ### ERROR ### Please RESET the board ### (The date of armbian of course depends on the version I'm running). The RESET seems to refer to a power cycle reset (which I obviously do each time I try to restart), so I dont see what I …

Well it took me longer than i hoped but i have managed to forward port icenowys code for TVE on the H2+/H3 to mainline armbian. It seems to work totally fine, with a few caveats. First: Sample images of it in action -> https://imgur.com/a/vXQEM Second: the patch itself -> https://github.com/stevenj/h3-tve/tree/v0.0.11 Third a prebuilt image for Orange Pi Zero: -> https://github.com/stevenj/h3-tve/releases/tag/v0.0.11 Howto: just put the patch into userpatches for the sunxi-next kernel, and build. it should apply cleanly. Its for H2+/H3. I have only tried it on a orange pi zero, but it should work on all H2+/H3 boards. …

Hi Srs! I have problem in using Armbian 14 with orange pi zero .. I already used the Armbian system in my OrangepiZero. However, I reinstalled everything again and downloaded the latest version of the operating system here on the site. When I try to use onboard audio (both capture and output) does not work. I have already enabled the analog-codec and it still does not work. Remembering that I already used the equipment with the Armbian and used the onboard capture of the board perfectly. Thanks!

Hi, Sorry for the newbie question. Is it possible to configure Armbian/OrangePiZero such as it can bridge 2 wireless networks. i.e.: connecting to an existing SSID to gain access to the internet, and at the same time servicing as an access point using another SSID ? And.... how do I do that ? Thanks in advance, Richard

Hi, Recently I upgraded /sudo apt-upgrade/ my armbian and my wlan is now gone /it worked perfectly before/. Looks like xradio module is missing from the new kernel? I am trying to download driver from http://linux-sunxi.org/Wifi, especially from http://kaiser-edv.de/tmp/lGtv38/patch-add-support-xr819.tar.gz .... but the site is not working.

Hey I followed the instructions on this page: https://kaspars.net/blog/linux/spi-display-orange-pi-zero But I can't get my 3.5" TFT Touchscreen work: https://aliexpress.com/item/3-5-3-5-Zoll-TFT-LCD-Touchscreen-320x480-SPI-RGB-Display-Board-F-r-Raspberry/32834124804.html I’ve got an Orange Pi Zero with armbian (ubuntu with legacy kernel). I only see the backlight LED is working (white screen). On kaspars blog everything looks so easy. I hope someone can help me with my problem. Thank you in advance guys!

I have a problem with my Opi z+, it is assumed that its maximum frequency is 1200 Mhz, but it does not rise from 816 Mhz. I use a Raspberry charger, of 3000 mha. I changed the governor to performance but it does not go up to 816 Mhz. I use Armbian, based on ubuntu 18.04

HI, guys. i need help, with my orange pi zero + mpc2515. My connect, is the same as this image. Int connect to PA7. mcp-2515.dtbo: /dts-v1/; /plugin/; / { compatible = "allwinner,sun4i-a10", "allwinner,sun7i-a20", "allwinner,sun8i-h3", "allwinner,sun50i-a64", "allwinner,sun50i-h5"; fragment@0 { target-path = "/clocks"; __overlay__ { #address-cells = <1>; #size-cells = <1>; can0_osc_fixed: can0_osc_fixed { compatible = "fixed-clock"; #clock-cells = <0>; clock-frequenc…

I encountered a strange problem and I do not know what to do: When I am restarting my OPI with inserted USB audio card, then LIRC does not work. When I am restarting my OPI without inserted USB card and this USB card I put only later after a restart, then LIRC works. Can anyone advise how to proceed? I need to insert USB audio card permanently (it's inside the device).

Hello, I'm trying to get an "Orange Pi Zero" running with Wifi and OV534 (Sony PS3 Webcam). I can't get both running at once. My attempts so far: Armbian_5.30_Orangepizero_Ubuntu_xenial_default_3.4.113: Wifi ok, no ov534 Armbian_5.30_Orangepizero_Ubuntu_xenial_dev_4.11.3: No Wifi, ov534 ok Armbian_5.32.170912_Orangepizero_Ubuntu_xenial_dev_4.11.12: No Wifi, ov534 ok I've read about XR819 on github posts (to use under 4.11), but I couldn't load it, there are three module files for this module: fw_xr819, boot_xr819 and sdd_xr819, but none of these is loading successfully: modprobe: FATAL: Module xr819 not found in directory /lib/modules/4.11.3-sun…

The Orange Pi Zero +2 H3 with USB hat will hard lock up on boot at "Starting Armbian Hardware Monitoring" when booting the latest (and at least one previous) available Buster (and Bullseye) images over HDMI console. Tested on multiple SD cards with the same result. (I will test with serial later, I do not have the time to remove it from the case at the moment; I figured I would post it now in case anyone had a chance to check before I could.)

Hello, i try to move it from SD to eMMC on a Orange Pi Zero +2 H5, but without success. Shouldn't be two partion created on eMMC by the nand-sata-install script ? root@orangepizeroplus2:~# fdisk -l /dev/mmcblk2 Disk /dev/mmcblk2: 7.3 GiB, 7818182656 bytes, 15269888 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0xe8c6ce8d Device Boot Start End Sectors Size Id Type /dev/mmcblk2p1 8192 15117183 15108992 7.2G 83 Linux Old UUID: /dev/mmcblk0p1 SD UUID: UUID=85ffa85e-4784-4cfd-93bb-db6f93f8e…

I have Armbian 22.02 Bullseye installed on my Orange Pi zero. The wifi connection worked fine at first, but after a few reboots the device 'wlan0' seems to no longer exist. In the Armbian-config settings the entry wifi is no longer present and also in ifconfig wlan0 is no longer displayed. I have now reflushed the system 3 times and always have the same problem.

So I have an application which requires 1Mbps UART and wasted a few days trying to debug my board thinking that was the issue (was working perfect at 115kps), so I decided to scope the UART TX from the orangpi, and of course that signal was not actually working at 1Mbps. Scope is saying that its running at 750Kbps. Did some research and it looks like there is some sort of UART scaling frequency set in the driver, which excludes certain bitrates from running (check here https://github.com/jernejsk/linux/blob/master/drivers/tty/serial/sunxi-uart.c#L356-L381 ) Did some further tests and 460Kbps works fine as well as 1.5Mbps (so its not an issue w…

Orange Pi Zero 2 After installation Armbian 22.02 Focal stopped loading. help me please in UART outputs the following U-Boot SPL 2021.01-rc4-armbian (Jan 05 2021 - 03:01:27 +0100) DRAM: 1024 MiB

Using the latest FW Image https://redirect.armbian.com/orangepizero2/Bullseye_legacy the Orange Pi doesn't boot anymore or at least I'm not able to establish a ssh connection. If I use the the archived previous version the board behaves completely normal until I perform an "apt upgrade". After upgrading it also doesn't boot anymore.

Hi I am using an OrangePi Zero 2+ with AllWinner H3 and i need both uart. I enable them with armbian-config and on pins Uart2 on pins 8 and 10 work fine bat uart1 on pins 11, 13 don't. The pin on this board is not the same as orangepi zero? I mast make some setup to make uart1 to work? auto@orangepizeroplus2-h3:~$ uname -a Linux orangepizeroplus2-h3 5.9.14-sunxi #20.11.3 SMP Fri Dec 11 20:31:12 CET 2020 armv7l armv7l armv7l GNU/Linux auto@orangepizeroplus2-h3:~$ cat /boot/armbianEnv.txt verbosity=1 bootlogo=false console=both disp_mode=1920x1080p60 overlay_prefix=sun8i-h3 overlays=i2c1 uart1 uart2 uart3 usbhost2 usbhost3 …

Hi, Does anyone has image for Orange Pi Zero 2+ H3 Ubuntu Dekstop Kernel > 4.x? Thanks.

recently I installed the Ubuntu Desktop on Orange Pi Zero 2+ H3 the Orange Pi Zero 2+ H3 device has only one micro USB OTG port during the first Armbian installation this port should be in dual mode -> power of course and in my opinion the second mode should be a HID gadget (g_hid) in this case we will be able to plug the keyboard via some micro USB hub and setup the system unfortunately this doesn't work like this and right now the installation process isn't so ease now the questions begins -> is it possible? Any clue how to do this? Thx PS I was able to do the installation because I have Orange Pi Zero E…

Hello everybody! I wanted to report that I was unable to boot with the "Bionic minimal 20.02.0-rc1" image "Bionic minimal 19.11.6 current" did not work either The red onboard is led flashing nothin else works. The Bionic download link on the top of the page is dead as well. With the same board, SD-card, power supply and USB cable I had no problem so far running the "Buster 20.02.0-rc1 current" image (beside some "armbian-configuration" flaws Did not try any further debugging so far any ideas? Andreas

Hello, I'm new to this forum and Armbian. I've got an Orange Pi Zero 2+ H5 running the Armbian_5.34.171121_Orangepizeroplus2-h5_Ubuntu_xenial_next_4.13.14 image. It's connected to a device via UART1 using pin 1 for 3.3V, 6 for GND, and 8/10 for TX/RX. I've been trying unsuccessfully to use pyserial in a Python script to read data from the ttyS* devices, but I can't seem to cat anything from them either. I've tried moving the device to a RaspberryPi Zero W and I'm able to read the output from ttyS0 successfully. I did have to run raspi-config to enable the UART on the RPi, but I'm not aware of an equivalent on the OPi. I believe I added the uart1 overlay to my…

I have my Orange Pi Zero flashed correctly (I think) with the green light solid and the red light flashing on every so often. I've got the unit plugged into a charger that provides sufficient power. The devices SoC warms up hinting that it is actually booting. When plugged into my network the activity LEDs do not flash nor does my router detect it. I'm considering connecting my keyboard to connect it to wifi blind. If I plug it in after boot nothing changes. What should I do? How can I connect it to my wifi blind? I do not have the shield for video out.

diagnostics listing of Orange Pi Zero 2W http://ix.io/4Lwr Not sure if this helps..but the stock build is lacking...plus I am getting 1.0 cpu usage at idle Orange Pi 1.0.0 user-built System too busy for benchmarking: 16:33:21 up 25 min, 3 users, load average: 1.15, 1.03, 0.92 System too busy for benchmarking: 16:33:26 up 25 min, 3 users, load average: 1.14, 1.03, 0.92 System too busy for benchmarking: 16:33:31 up 25 min, 3 users, load average: 1.13, 1.03, 0.93 System too busy for benchmarking: 16:33:36 up 25 min, 3 users, load average: 1.12, 1.03, 0.93 System too busy for benchmarking: 16:33:41 up 25 min, 3 users, load average: 1.11, 1.03, 0…

Hello, I'm trying to connect an PCF8574 I2C adapter to my Orange Pi, but it doesn't show up in i2cdetect, only something at 0x30 on i2c0 and 0x36 on i2c1 that is labeled UU. I tried to connect it to arduino, and it found it on address 0x27 Connected on pins 3 and 5 root@orangepizero2w:~# sudo i2cdetect -y 0 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: 30 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -…

Hi everyone, I'm new to Orange Pi Zero 2w and Armbian. I'm trying to use the image on the zero2w. Installing on the SD fits and works so far. Unfortunately, there is no image on the screen via the HDMI port. Could it be due to the image? The old OrangePi image with the 5.x kernel works so far. Do you have an idea? Best regards

After many days spent wondering why is my OPI Zero2w 1.5GB not booting some Armbian images (xfce desktop version for example), I have found there is a "bug" or difference in uboot models 1.5GB + 4GB vs 1GB+2GB. Fix that might work for Zero2w is here https://forum.armbian.com/topic/31654-orange-pi-zero-2w/ (planning to test it soon) Can somebody confirm Opi Zero2W 1.5GB has still this issue with some Armbian images ? Armbian minimal boots without aby issues. Not sure why it works and desktop doesnt.

Hello, I've issue with nameserver. My router DHCP DNS server point to the Pi which has IP 10.6.6.3. But for unknown reason 1.0.0.1 keep added in the /etc/resolv.conf: # This is /run/systemd/resolve/resolv.conf managed by man:systemd-resolved(8). # Do not edit. # # This file might be symlinked as /etc/resolv.conf. If you're looking at # /etc/resolv.conf and seeing this text, you have followed the symlink. # # This is a dynamic resolv.conf file for connecting local clients directly to # all known uplink DNS servers. This file lists all configured search domains. # # Third party programs should typically not access this file directly, but only # through the symlink a…

Hello, I'm using USB C to Ethernet adapter and the download speed is below 1Mbps while upload speed as expected. I have 600Mbps down and 500Mbps up ISP plan but since the adapter used USB2.0 it should cap both down and up at ~90Mbps, at least I have tested this with a Galaxy Tab. Image: Armbian_community_24.8.0-trunk.399_Orangepizero2w_bookworm_current_6.6.36_minimal.img.xz Power supply: 5V2A SD: Sandisk Ultra 64GB Adapter (100Mbps): Speedtest: ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 in…

Hi, does anyone know where I can find a build for linux 5.1 for my orange pi zero 2w. I would like to use fbtft device, so either finding a pre 5.4 linux build, or building one myself (In that case how so because I failed miserably) or an alternative to fbtft. Thank you very much

Hi, I have Armbian_community_24.8.0-trunk.6_Orangepizero2w_bookworm_current_6.6.31_minimal on my Orange Pi Zero 2W. It has an expansion board but the ethernet port does not work on it. ip a show eth0 >> Device "eth0" does not exist. Only the Wi-Fi works.

Hi, How to enable i2c on PI8(SDA) and PI7(SCL)? I'm newbie in linux and not really understand what am I actually doing so I tried to make it with chatgpt but still not working. root@orangepizero2w:/# sudo i2cdetect -y 0 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- UU -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 70: -- -- -- -- -- -- …

Hello Armbian community, Firstly, thank you for the amazing work that you do. Having Armbian has made the setup process so simple, and I really appreciate that I'm completely new to the world of SBCs and Armbian (but not Linux), and this issue had me stumped for a long time. I wanted to share the solution for those who are in the same position as me, as I only found this on Raspberry Pi resources. Sorry if this has already been covered elsewhere in the forums - my searches didn't show any answers from here, and additionally, I keep getting time-locked (forced to wait 30sec) for every forum search. The model of OPI I have is the Orange Pi Zero 2…

I need some help with this LCD https://www.amazon.com/dp/B0CMD7Y55M?ref=ppx_pop_mob_ap_share, i bought it since i verified whith the always unreliable AI GPT if it would work with my Orange Pi since i want to use the screen in my klipper 3d printer. Now im stuck since the available driver from the manufacturer are only for the Arduino and RP2040. I verified evrywhere and could only find one github but that one did not work for me and there are no tutorials of how to work with this. Does some one have any idea of how to make this run or work?. Just in case my wiring is as follows:

Armbian_community_25.5.0-trunk.538_Orangepizero2w_bookworm_current_6.12.23_minimal.img When try to boot. It get stuck trying to boot from emmc. It does not have emmc. After several power restart sometimes it boots form microsd. also it ask for tags which has only one option "Solved". I had to tag this topic as solved in order to be able to submit it.

I installed Armbian on my Orange Pi Zero 2W—my first time doing this—but the keyboard doesn't work when I connect it via the USB-C adapter I'm using. I considered an SSH connection as an alternative, but I don't know how to set it up without a keyboard, nor do I know how to configure Wi-Fi and SSH settings via the SD card. Please help.

the tft is working well on stock orangepi image but when I try the prebuilt armbian images or build it myself it look like this my dts file: 35Lcd.dts

has anyone ordered and/or played with this https://www.cnx-software.com/2023/07/03/orange-pi-zero-3-allwinner-h618-sbc-ships-with-up-to-4gb-ram/ https://liliputing.com/orange-pi-zero-3-is-a-cheap-tiny-single-board-pc-with-up-to-4gb-ram-gigabit-ethernet-and-allwinner-h618/ http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/details/Orange-Pi-Zero-3.html even the linux images is very 'fresh' as in that they are just released *yesterday* 😄

Hello! PWM seems to work without any configuration on the factory images with the gpio command, but I cant seem to get it to work on armbian. There doesn't seem to be any dtbs related to pwm, and /sys/class/pwm is empty on armbian. Anyone got this to work? EDIT: Forgot to add, doesnt seem to be any pwm overlays present on armbian install

Yesterday, I tried to use the digital IO in my opi zero3, with the Python GPIO package from https://opi-gpio.readthedocs.io/en/latest/ by Richard Hull It depends on having sysfs files in /sys/class/gpio/ My original opi zero has these files and it works, but my opi zero3 doesn’t have these files I learned that /sys/class/gpio is created if the linux kernel is configured with a specific option ON, as suggested in the documentation: https://github.com/rm-hull/OPi.GPIO https://linux-sunxi.org/GPIO Also, a developer has made a change on the opi.GPIO project to support opi zero3 https://github.com/rm-hull/OPi.GPIO…

I had an OrangePi Zero LTS and set up an access point using the following commands: % sudo apt install dnsmasq-base -y % sudo sed -i "s/#MulticastDNS=no/MulticastDNS=yes/g" /etc/systemd/resolved.conf % sudo nmcli connection add type wifi ifname wlan0 con-name access_point autoconnect yes ssid <ssid> % sudo nmcli connection modify access_point 802-11-wireless.mode ap 802-11-wireless.band bg ipv4.method shared % sudo nmcli connection modify access_point connection.mdns 2 % sudo nmcli connection modify access_point wifi-sec.key-mgmt wpa-psk % sudo nmcli connection modify access_point wifi-sec.psk "<password>" % sudo nmcli connection up access_point % sudo host…

I have this screen here ili9486 : https://pt.aliexpress.com/item/32805704334.html?src=google&pdp_npi=4%40dis!BRL!43.31!38.51!!!!!%40!12000019014148570!ppc!!!&src=google&albch=shopping&acnt=768-202-3196&isdl=y&slnk=&plac=&mtctp=&albbt=Google_7_shopping&aff_platform=google&aff_short_key=UneMJZVf&gclsrc=aw.ds&&albagn=888888&&ds_e_adid=&ds_e_matchtype=&ds_e_device=c&ds_e_network=x&ds_e_product_group_id=&ds_e_product_id=pt32805704334&ds_e_product_merchant_id=107713925&ds_e_product_country=BR&ds_e_product_language=pt&ds_e_product_channel=online&ds_e_product_store_id=&ds_u…

Help! I used your overlay, but nothing works for me. Orange pi zero 3 (Armbian Linux 6.12.35-current-sunxi64) overlay: /dts-v1/; /plugin/; / { compatible = "allwinner,sun50i-h616"; fragment@0 { target = <&spi1>; __overlay__ { status = "okay"; cs-gpios = <&pio 7 5 0>,<&pio 2 15 0>; /*PH5=CS0 for lcd, PC15=CS1 for touch*/ display: display@0 { compatible = "ilitek,ili9341"; reg = <0>; pinctrl-names = "default"; spi-max-frequency = <20000000>; rotate = <270>; bgr = <0>…

I'm trying to setup a GPS-based time server on an Orange PI Zero 3, running Armbian 24.8.0-trunk.495, kernel 6.6.43-current-sunxi64. I have the exact same hardware setup working fine on a RaspberryPI 4b, running RPI OS / Debian 11 (bullseye) , kernel 6.1.21-v8+ #1642. On the RPI4, gpsd recognises the (cheap chinese "M8N") GPS module as u-blox and keeps working in a stable way root@rpi4:~# gpsctl /dev/ttyS0 /dev/ttyS0 identified as a u-blox SW ROM CORE 3.01 (107888),HW 00080000 at 9600 baud. the /boot/config.txt has these two lines for the UART config enable_uart=1 init_uart_baud=9600 On the OPIZ3 I configured /boot/armbianEnv.txt for UART5…

hi can somebody fix repostiory install list error for chromium as chrome-commen and chromedriver wont install problem: chromium/noble 9:126.0.6478.182-1~deb12u1+narmbian1 arm64 web browser installs with version therefore chromium-common and chromium-driver,will not install because its looking for dependency chromium 126.0.6478.182-1~deb12u1+n1 Without the ":9" i presume he following packages have unmet dependencies: chromium-driver : Depends: chromium (= 126.0.6478.182-1~deb12u1+n) E: Unable to correct problems, you have held broken packages. please can somebody fix

I used python script with Orange pi zero 3 (Armbian_community_24.8.0-trunk.6_Orangepizero3_bookworm_current_6.6.31_minimal.img) Observation: 1) /dev/ttyS1 is actually Serial 2 as per pin diagram as per Orange Pi Zero 3 - Armbian web page 2) /dev/ttyS2 is actually Serial 5 as per pin diagram as per Orange Pi Zero 3 - Armbian web page 3) even if I set rtscts=True in crateing object ser in above script, there is no output on rts or cts pin. I am looking forward to have RTS pin remain high during transmission to easily integrate ic for RS485 communication. I was glad that Amrbian for Orange Pi Zero 3 has out of the box RTS CTS pin suppor…

Hello, I have been trying to get sound working on my Orange Pi Zero 3, and I am facing persistent issues. I installed every operating system listed on Armbian’s Orange Pi Zero 3 page and followed all the standard setup procedures. Despite updating all packages and even performing kernel updates, I have never been able to get any sound output from the device. I have checked multiple configurations, tried different OS images, and ensured that all drivers are up to date, but nothing works. The device otherwise functions normally, but audio simply does not come through under any circumstances. Could you please provide guidance or a solution? Any help would be g…

I'm trying to configure the CS (Chip Select) pin on my Orange Pi Zero 3. I added overlays=spi-spidev to the /boot/armbianEnv.txt file, created my own dtbo file, and tried all possible methods suggested by ChatGPT. I've been struggling for two weeks with no success. I haven't been able to switch the CE1 pin to alt4 state; it only stays off, nothing else. Is it even possible to work with SPI on this board?

I have an orange pi zero3 with 2gb of ram. Ive installed the current 6.18.43 armbian debian build. It booted fine from SD and I then flashed the boot rom to the eeprom so I could boot from USB (sudo flashcp /usr/lib/linux-u-boot-current-orangepizero3/u-boot-sunxi-with-spl.bin /dev/mtd0) I was able to boot from USB0 fine but not from the USB ports USB1 and 2 on the 13 pin header. With the help of google and some ai I found that if I run the following my sd card is recognised when plugged into usb1 fdt addr bbf107b0 fdt set /soc/usb@5310000 status "okay" bind /soc/usb@5310000 ehci_generic usb reset usb storage That produced: Bus usb…

I’m running Armbian debian minimal image on my Orange Pi Zero 3, using the onboard WiFi (wlan0) with the unisoc_wifi driver. The WiFi consistently drops with logs like these: [ 11.048517] unisoc_wifi wlan0: mixed HW and IP checksum settings. [259241.515808] unisoc_wifi wlan0: sprdwl_report_connection Asus failed status code:30! [345665.483530] unisoc_wifi wlan0: sprdwl_report_connection sm_state (5), status: (2)! [345665.483567] unisoc_wifi wlan0: sprdwl_report_connection Asus failed status code:1! NetworkManager also reports: link timed out. Activation failed for connection 'Asus' After the crash, restarting NetworkManager doesn’t reso…

Hi! So the problem is when I configure wifi hotspot using hostapd, isc-dhcp-server, and ifupdown, I'm able to start the AP, connect to it, and ping. However, the moment any device connects to the AP the serial console gets spammed with this message around once a second: protocol 0000 is buggy, dev wlan0 This happens on the unofficial Armbian build (from the Armbian OrangePi Zero3 page), DietPi, and the official OrangePi Debian build. The wireless band doesn't matter. Kernel version: 6.1.31-sun50iw9. I tried to set up the AP with NetworkManager, but couldn't manage to connect to it. Probably DHCP issues that I couldn't resolve. I haven't …

Hi Managed to get x11 to boot in latest armbian desktop Ubuntu gnome build x11vnc runs when manually running it fine but how many tutorials I have followed online it refuses to start as a service (auto) always gets bad access error when trying to get xauthority I guess ,even when I point it to the .xauthority files with -auth and used -auth guess tried all theses Tutorial 1 Tutorial 2 Tutorial 3 plus videos on YouTube has anyone got vnc to run on orange pi zero 3 Ubuntu noble gnome desktop From here at start up on x11? thanks

Hi, I am having problems connecting my orange pi zero 3 to my TV via hdmi: No matter what I try the TV reports "no signal". Before I came to armbian I have tried the vendor-supplied debian and arch images and could not get hdmi output on any of them, so it might be that my micro-hdmi adapter is faulty or that the hdmi-port on the device itself is faulty, but over the weekend I cannot replace any hardware so I thought I try here to see if anyone has an idea on what to try. The image I am currently running is Armbian_community_24.5.0-trunk.58_Orangepizero3_jammy_current_6.6.17_gnome_desktop.img. When I log into the device I ca…

Can the opi zero decode anything above 1080p? I want to decode a 3MP h.264 stream (2048*1538) and re-encode it to 1080p and serve over RTSP. do I need to get an H3 for that? the wiki says http://linux-sunxi.org/H2%2B#Variants Is that HDMI specific or lack of GPU power for decoding? Will that be pushing it too much even on an OPI PC?

I have an Orange Pi Zero 512 H2 with the "original" audio breakout-shield AKA Orange Pi Zero Interface boatd 1.1 like this one http://codelectron.com/intro-to-orange-pi-zero-interface-board/ I loaded the latest Armbian Buster, did apt-get update apt-get upgrade So I have Armbian buster with Linux 5.4.43-sunxi and then tried to send an audio signal to the sound output via speaker-test -twav -c2 root@orangepizero:~# speaker-test -twav -c2 speaker-test 1.1.8 Playback device is default Stream parameters are 48000Hz, S16_LE, 2 channels WAV file(s) ALSA lib confmisc.c:767:(parse_card) cannot…

Orange Pi Zero 512 MB has a serious wifi problem. After i connect the wifi network, i loose connection and i can't access my zero until i connect with ethernet cable. Interestingly, after i connect ethernet cable, wifi reconnects. i set up my wifi connection with nmtui. Auto connect enabled. I really need to solve this wifi issue. In my thinking there two options, which one is better i don't know. 1 st option: I have to buy wifi adaptor, but i don't know will it solve the problem. (and probably i am going to have driver problem) 2nd option: I am going to write a new thread with python. This code will check wifi connection every 10 seconds, if …

I there i use the update my orange pi zero to latest version 04/05/17 and no simply dosen´t boot anymore! any thing i can do?

Hi I have use Armbian v5.31 Debian jessie kernel 4.11.5-sun8i with Orange Pi Zero. When I have use armbianmonitor or rpimonitor always information about CPU frequency is null. The directory sys/devices/system/cpu/cpu0/cpufreq/ are empty for this reason rpimonitor don't show related information to CPU CPU total: undefined% (Sys: undefined%, User: undefined%, I/O wait: undefined%, Nice: undefined%) CPU frequency: undefinedGHz DRAM frequency: Not available Regards

Hi, I just got my hands on a Orange Pi Zero, but when I try to use iscsiadm I get the following message: iscsiadm: iSCSI driver tcp is not loaded. Load the module then retry the command. iscsiadm: Could not perform SendTargets discovery: iSCSI driver not found. Please make sure it is loaded, and retry the operation I have tried to load the module using modprobe, but it does not seem to exist. Any tips?

Hi, I have today on ma Orange Pi Zero switch kernel from dev 4.11.12 to NEXT kernel 4.13.4 and notice that defined modules in /etc/modules file are not loaded during start system I must manually load and in log system: 0.002070] CPU: Testing write buffer coherency: ok [ 0.002628] /cpus/cpu@0 missing clock-frequency property [ 0.002662] /cpus/cpu@1 missing clock-frequency property [ 0.002692] /cpus/cpu@2 missing clock-frequency property [ 0.002725] /cpus/cpu@3 missing clock-frequency property and armbianmonitor don't show CPU frequency but on kernel 4.11.12 was OK I know that NEXT kern…

Hi, Can anyone share a version of nightly build for Orange Pi Zero Debian Jessie with kernel 4.11.12 or newest for testing? I don't have the possibility to build own version of Armbian but I can try and tests existing distributions armbian. At current, I have use armbian Debian Jessie with kernel 4.11.5 Regards

hi guys i have little problem i connect my orange pi zero directly to relay but not work the realy is HUI KE hk19f-dc 5v-sh in yellow box , but if i attach 3v and gnd of gpio work o_O anyone can help me?? thankz

How install linux-tools for USBIP >usbip WARNING: usbip not found for kernel 5.15.43 You may need to install the following packages for this specific kernel: linux-tools-5.15.43-sunxi linux-cloud-tools-5.15.43-sunxi You may also want to install one of the following packages to keep up to date: linux-tools-sunxi linux-cloud-tools-sunxi >apt install linux-tools-sunxi Reading package lists... Done Building dependency tree... Done Reading state information... Done E: Unable to locate package linux-tools-sunxi I tried linux-cloud-tools-sunxi, linux-tools-5.15.43-sunxi, linux-cloud-tools-5.15.43-sunxi BUT …

Has anyone successfully configured OPI0 AP working in the mainline kernel? I have tried to use the same configuration file with the 3.4 kernel, the hostapd started successfully, dnsmasq also running, but when client device trying to connect to the AP, the client is not able to obtain the IP address from the dnsmasq-dhcp server. the dnsmasq log: journalctl -f -- Logs begin at Sun 2017-01-22 13:30:20 UTC. -- Jan 22 14:47:52 orangepizero dnsmasq-dhcp[1676]: DHCPOFFER(wlan0) 192.168.43.125 cc:08:8d:d5:92:84 Jan 22 14:48:00 orangepizero dnsmasq-dhcp[1676]: DHCPDISCOVER(wlan0) cc:08:8d:d5:92:84 Jan 22 14:48:00 orangepizero dnsmasq-dhcp[1676]: DHCPOFFER(wlan0) 192.168.43.…

Hello, I'd like to disable the yellowish and green ethernet port LEDs on Orange Pi Zero. At night, it becomes quite shiny and is really disturbing. Any methods to do this on the software end? If not, I'm planning to apply some nail polish :-/ Thanks in advance,

verry bad screen with armbian-config and alsamixer using ( lxterminal, mate terminal, putty on Linux mint Buster ) works better with xterm , on previous armbian version Jessie or stretch it's fine with all terminals . 2 first screenshoot are made on lxterminal , third on putty . the 4th one is my dialog menu and it's ok on all terminals

Hi , I want to try out a project for a friend of mine and use an orange pi zero (for now , stronger model might replace it later) to do the following : have an outdoor ip cam connect with wifi on the orange pi zero Save videos on motion detect on pi`s memory Upload saved videos to a remote server (could be ftp) eg. every midnight with internet access via ethernet Keypoints : ipcamera must connect with pi`s wifi pi will connect to a router (via ethernet) a couple hours per day so the setup must not be internet based or with any extra equipment except the pi and the ipcam My thought of doing it : …

Have not been able to confirm if it is possible for the Orange Pi Zero to act as a virtual mass storage device. I would like to be able to plug this into a device and have that device treat the Pi Zero as a USB drive, and write to the on board SD as such. I believe this requires USB on the go so that the device can be USB slave. Any input on the topic is appreciated. I know the Raspberry Pi Zero W supports this, but I think i will have better luck with the wireless having an external antenna on the Orange Pi Zero.

When I have to use Jessie version dev with kernel NEXT 4.13.5. The alsamixer have different options to setup audio compare to ARMBian with stable kernel 3.x I must switch on DAC Reversed to have audio output in speakers. I don't know it is correct but works for me. The input mic is very sensitive and must be lower value to have good quality sound I don't know why is displayed option for MIC2 , the orange pi zero has only one microphone input

I there im using orange pi zero for homeassisatnt and google assisatant since my card died i install this new version configured every thing but audio isn´t working! I fallowed this guide like before but no audio coming for my orange pi zer no recording either! I have activated analog audio I already have everything configured with homeassistant i don´t wanna configure all again! Can you please help me make audio work in this kernel or is impossible to do?

Armbian_20.05.3_Orangepizero_buster_current_5.4.45.img apt install cryptsetup lvm2 thin-provisioning-tools All ok if install any two, size problem?

Hi, I have a orange pi zero with NAS expansion (128 MB msata drive) I would like to boot only msata.... So, How I to do ?

This was my second attempt and it finished with exactly the same result. Console log: ~$ ssh admin@zero ___ ____ _ _____ / _ \ _ __ __ _ _ __ __ _ ___ | _ \(_) |__ /___ _ __ ___ | | | | '__/ _` | '_ \ / _` |/ _ \ | |_) | | / // _ \ '__/ _ \ | |_| | | | (_| | | | | (_| | __/ | __/| | / /| __/ | | (_) | \___/|_| \__,_|_| |_|\__, |\___| |_| |_| /____\___|_| \___/ |___/ Welcome to ARMBIAN Debian GNU/Linux 8 (jessie) 3.4.113-sun8i System load: 0.07 Up time: 3 min Memory usage: 9 % of 494Mb IP: 192.168.8.9…

I'm trying to set up one of my Orange PI Zero to be a MPD Player and in parallel to play streams from other devices over network. The streams are provided by a Ubuntu desktop PC and and a Librelec PC. The Orange Pi Zero is running Armbian 5.38 with Kernel 4.14.18. I tried the last days two solutions: ALSA dmix plugin playing everything except network streams and Pulseaudio for nework streams Playing everything through Pulseaudio in system mode The first solution failed as the dmix plugin in ALSA has poor performance and causes regularly high CPU load resulting in broken audio playback with MPD The second solution seemed to be better s…

Hello , I first time to use not do anything just to apt-get update but get this message ! This image may have problem . Thank !

Hi friends, I am trying to downclock my OPi Zero and set/disable unused cores 1,2,3, limit DRAM speed, limit max cpu core frequency, put voltage down. Is this possible on Opi Zero? I tried e.g. but when I cat /sys/devices/system/cpu/cpu3/online is is always 1. Any idea please? Some advice how to do all of this is highly appreciated. I am trying to downclock Opi Zero to push produced heat down.

Hello, I have OPI0 with Ubuntu 20.04.1 LTS with Linux 5.8.6-sunxi and I would like to set 240 MHz as minimum frequency. cpufreq-info shows that available steps starts at 480 MHz but on older kernel 240 MHz and 120 MHz were available too. I also tried to "force" 240 and 120 by editing /etc/default/cpufrequtils but no go. Lower reachable frequency is 480 MHz and what I see are a bit CPU higher temperatures. cpufreq-info cpufrequtils 008: cpufreq-info (C) Dominik Brodowski 2004-2009 Report errors and bugs to cpufreq@vger.kernel.org, please. analyzing CPU 0: driver: cpufreq-dt CPUs which run at the same hardware frequency: 0 1 2 3 C…