Allwinner sunxi

Hello guys, I configured bridge via nmcli/nmtui br0. Slave devices of bridge are eth0 and wlan0(as wifi access point). OS: Armbian_5.59_Orangepizero_Ubuntu_xenial_default_3.4.113 root@orion2:~# nmcli c s NAME UUID TYPE DEVICE bridge-br0 fff57bce-6051-458d-9394-7101741af59f bridge br0 bridge-slave-eth0 25720542-2bdd-498e-992e-4415385673d5 802-3-ethernet eth0 bridge-slave-wlan0 ed8b07bf-a793-4717-8c99-2e84d54af672 802-11-wireless wlan0 Configuration looks fine, but when I try login to AP, my smart phone shows error message: "Authentication issue" , an…

Hello everyone, I'm having some isues with my olimex board. It boots fine on the images supplied by olimex. But the Armbian legacy images wont boot. I have a serial connection to the board it hangs on the following line: <6>axp20_ldo2: 1800 <--> 3300 mV at 3000 mV. http://pastebin.com/nEHAiZHa I need legacy for i2s support so mainline isnt an option. I use the following board(tried 3 of these): https://www.olimex.com/Products/OLinuXino/A20/A20-OLinuXino-LIME-4GB/open-source-hardware I used the following armbian image (jessie and wheezy give the same error): http://www.armbian.com/olimex-lime/ Building the image myself also doesnt work.…

I have recently been trying to get my spi ili9341 working under kernel 6.6, having gotten it working previously. I checked to ensure there were no changes in the overlay required by the newer kernel. I confirmed that the pins were configured correctly and that the ILI9341 DRM module had loaded.. Despite this I was met with a white screen. Think I must have missed something I swapped out my SD card for another using an image based on kernel 5.15.88, where I was able to recieve a display. Looking back over the dmesg log, I noticed a slight difference in behaviour with the older kernel. firstly we can clearly see that the SPI driver is requesting to use gpio 34 as…

Hi all, I need to enable rts/cts on my OrangePi Zero with Armbian buster with Linux 5.4.26-sunxi installed. I added the "param_uart2_rtscts=1" (I'm using /dev/ttyS2) to the /boot/armbianEnv.txt file On mi code I use this initialization of the port. xxxxx.c_cflag |= port_parity | port_bits | port_stop | CLOCAL | CRTSCTS | CREAD; Not only rts/cts but also the tx and rx pin aren't working now. Has anyone managed to enable the port on this board? Am I doing something wrong?

I've had an Orange Pi Zero Plus 2 H5 for a few months, and it is driving me crazy. I can easily boot into the useless Android distro included on the eMMC. I can run most of the distros on the OrangePi website, although they seem to all be missing features or not working 100% in one way or another. I would LOVE to run Armbian on this board. Each time I try, I have huge problems. My video signal is often garbled or at best full of artifacts. I get segfaults every few minutes, and it seems like the filesystem is corrupted. I've tried running it with multiple power supplies (I have several Canakit 2.5amp ones), as well as several different gen…

Hello, on Cubietruck, until I upgrade my ARMBIAN server from Jessie to Stretch with kernel 4.13.16-sunxi, I could use the VGA output for display. After the upgrade, I don't have any display from VGA. In /boot/boot.cmd, I have the following kernel bootargs : "console=tty1 root=/dev/mmcblk0p1 rootwait rootfstype=ext4 sunxi_ve_mem_reserve=0 sunxi_g2d_mem_reserve=0 sunxi_no_mali_mem_reserve sunxi_fb_mem_reserve=16 hdmi.audio=EDID:0 disp.screen0_output_mode=1920x1080p60 panic=10 consoleblank=0 enforcing=0 loglevel=1" Any advice ? Thanks in advance, Romain

Hi, I got one of those cheap 300Mbps wifi dongles with 8192EU chip with USB Vid/Pid 0bda:818b. How can we enable this in Armbian? lsmod does not show any detected h/w driver and wan0 is not showing up in ifconfig. Only lsusb has the following root@nanopineo:~# lsusb Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 0bda:818b Realtek Semiconductor Corp. Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b…

Hello, I've purchased a 2e recently, in order to replace a RPI3 with a more powerful device (and get graphics acceleration, be able to watch youtube videos, etc). I've tested multiple builds, and even on the legacy kernel, there is just no way to get it to work properly. The board, when it sits completely idle, is between 48 and 52°. And if I move a window on the desktop, it's all laggy and the cpu jumps to 60+° --the same with a mainlain image in fact, in headless mode... frequently the console would freeze for a couple seconds while the temperature is very high for no reason. It seems there is no hardware graphics acceleration, ever. Curr…

Hi forum, I ran an apt-get upgrade a few days back and here linux-image-current-sunxi:armhf was updated from 21.05.6 to 21.08.2 After reboot my SATA was gone. There was nothing in the logs which would have indicated that something is wrong. After I reverted back to 21.05.6 apt-get install linux-image-current-sunxi=21.05.6 apt-get install armbian-firmware=21.05.8 apt-get install linux-dtb-current-sunxi=21.05.6 everything worked again. Has anyone experienced something similar ? Regards Volker

Hi Sorry my english and my ignorance in linux I'm trying to activate hostapd on orange pi light. I think realtek driver. Nework appairs, but i cannot associate, it says wrong password (12345678) iwconfig has not password item: Spoiler iwconfig lo no wireless extensions. br0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"ARMBIAN" Nickname:"<WIFI@REALTEK>" Mode:Master Frequency:2.432 GHz Access Point: 2E:98:51:56:D5:65 Bit Rate:72.2 Mb/s Sensitivity:0/0 Retry:off RTS thr:off Fragment thr:off …

Hello; My OrangePi PC HDMI port is dead, it throws no input signal, and I've read that this board has no ESD protection for HDMI, so I assume it died because of it. What I want to get is video working through analog TV out, but I can't seem to find the solution for this. I guess it should be simple task, but I never did it before. Hopefuly somebody can give me the solution. Thanks!

Dear forum, When looking at the Orange Pi Zero schematic V1.1, the OSC-RTC box is empty. Does this mean that there is no crystal for the internal RTC? The internal RTC cannot be used at all? When just checking the time register, the RTC is running too fast. Thanks, Arjan

Hiya, I'm attempting to use Wifi on the Banana Pi M1Plus board, supposed to be a Banana Pro clone from SinoVoip, but I cannot get the wifi module working with the latest Armbian 4.5, Jessie kernel 3.4.109. I have already linked script.bin to the /boot/bin/bananapro.bin file I try loading the ap6210 module and it gives errors. root@bananapi:~# modprobe ap6210 <3>[ap6210] parse wifi_used failed in script.fex. <3>[ap6210] bluetooth is disable in script.fex. <3>[ap6210] [dhd_module_init] get wl_host_wake gpio failed modprobe: ERROR: could not insert 'ap6210': Operation not permitted Thankyou for any help Lemonzest

Hello guys. I try to configure AP on WiFi. I have created /etc/hostapd/hostapd.conf: interface=wlan0 driver=nl80211 country_code=IN ssid=TEST hw_mode=g channel=6 wpa=2 wpa_passphrase=12345678 wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP auth_algs=1 macaddr_acl=0 Then I have uncommented DAEMON_CONF="/etc/hostapd/hostapd.conf" in /etc/default/hostapd. After it, I run /etc/init.d/hostapd restart And I try to scan WiFi via mobile phone, and no TEST. What am I doing wrong?

Hi I tried several image but cannot boot..it is compatible for orange pi PC ? my target is BTSync. thanks

TRYING TO CLONE EMMC FROM ONE NEO CORE INTO ANOTHER. I found this link below : https://github.com/zador-blood-stained/fel-mass-storage I still don't know if it works since i had to enter FEL MODE which i could not. maybe i am trying in a wrong way. SO how could i get a clone EMMC of nanopi neo core (taking into consideration it might not have FEL mode)? but if it does then how to enter this mode? and how to run this clone on another nanopi neo core?

Hi Dear Friends! I'm having trouble using the onboard analog soundcard from my OrangePi Zero +. I already enabled analog-in in armbian-config, but when I try to run some application that uses the sound card, it has an error. In this example I'm trying to use the direwolf app that serves to decode FSK audio. The error also repeats when I try to use svxlink.

I have Orange PI PC Plus with GC2035 camera module. Upgraded to 4.13.6 sunxi-next mainline kernel and noticed that GC2035 camera driver is gone! Why is it so? Maybe someone forgot to include this driver to the kernel? People are still using these cameras and need them! If it was a conscious decision to remove the GC2035 camera from the sunxi-next tree - then, well, it was a horrible decision that should be reversed. Please return this driver. https://github.com/avafinger/gc2035 Earlier it was at ./drivers/media/video/sunxi-vfe/device/gc2035.c location, but now the directory structure could be very different...

Hello, it seems like there are no dts files to add support for i2s. How hard would it be to complete this task? The documentation from h6 references support for i2s, and the same in the user manual from Xunlog : http://dl.sumnic.com/download/OrangePi-One-Plus.pdf Edit:After some reading, i2s is not working for now and there's no proper driver yet. Thanks to martinayotte, SPI is working.

Hi all, some days ago I successfully built the image mentioned above (Build environment is Ubuntu 14.04/64 bit). The only remarkable issue was the ever-repeating "firstrun" script, which was easily solved with the method mentioned here: http://forum.armbian.com/index.php/topic/1100-post-install-scripts-on-every-reboot/#entry8509 (may be ALL of the scripts should be changed this way?) But today, after checking out the actual "master", I see a lot of failed copy and sed commands until the debootstrap-ng script finally fails at Mali-libdri2. The 1st occurrence of an error was during installation of "ramlog". I've inserted a breakpoint and looked into the imag…

So I have an OPI0 perfectly running then suddenly it freezes. All I can find on /var/log/syslog Jul 1 10:35:10 localhost CRON[1553]: (root) CMD (command -v debian-sa1 > /dev/null && debian-sa1 1 1) Jul 1 10:36:08 localhost rsyslogd-2007: action 'action 10' suspended, next retry is Sun Jul 1 10:36:38 2018 [v8.16.0 try http://www.rsyslog.com/e/2007 ] Jul 1 10:37:07 localhost rsyslogd-2007: action 'action 10' suspended, next retry is Sun Jul 1 10:37:37 2018 [v8.16.0 try http://www.rsyslog.com/e/2007 ] Jul 1 10:38:07 localhost rsyslogd-2007: action 'action 10' suspended, next retry is Sun Jul 1 10:38:37 2018 [v8.16.0 try http://www.rsyslog.com/e/200…

Edit: Price seems to be $17.99 Just FYI: FriendlyARM is preparing another H3 board: NanoPi Air somehow related to NanoPI NEO (same low default DRAM clockspeed let me believe this). What we already know (by looking at Github commits): onboard eMMC (no idea about the size) no HDMI no Ethernet AP6212 based WiFi+BT (connected through SDIO and UART) Personal assumptions: most probably also just a single bank DRAM configuration most probably also a SD card slot maybe eMMC only an option and a basic version without eMMC available same 40 x 40 mm dimensions as NEO, eMMC on the lower PCB side next to H3, AP6212 on the upper (where the Ethernet Jack is located on the NEO -- a…

Hi Struggling here with Orange's GPIO so I would be glad to see any pointer to a working gpio example for 3.4.x kernel. Even a simple one pin state switching would be great. Christos

It looks like there is no hardware accelerated video decoding/encoding on the Banana PI M1 currently (on the server build). Is there any chance to enable it?

Hi, I have quiet a problem getting ipsec/strongswan running on my Orange Pi R1. IPSec is configured fine and it connects to my vpn gatway by establishing and ikev2 connection with the help of transform (xfrm) interfaces. After connection everything works fine, but not for long. When I transfer large amounts of data (e.g. iperf3) the whole Orange Pi R1 freezes suddenly. This occours almost immideatly, sometimes i get a couple of seconds a data stream, but mostly it freezes at once. Currently I use even the lates "Linux orangepi-r1 5.9.1-sunxi #20.08.14 SMP Tue Oct 20 23:01:54 CEST 2020 armv7l GNU/Linux" Kernel, and I upgrade…

Hello there, I tried to use on OPC3 bionic the ttyS1 for communcation with a serial device and didn't get it to work. ttyS3 works fine. Configuration is done for both. But now I need to communicate with a second and possibly a third serial device. So I hoped for updates. But now I can't find a download of the bionic version and i have to make decision how to go further on. Does it make sense to switch to buster or stretch? Is bionic only temporarily or finally offline? Whats the reason? Any idea when there is a chance to get a stable release. Possibly with 6 Months or surely not within 6 months. Which version is more likely to …

Remark: on my Orange Pi PC and Orange Pi Plus 2e - everything is OK. Problem occurred on Orange Pi Plus 2 and Orange Pi Zero After upgrading to: [root@PKTEST ~]# uname -a Linux PKTEST 5.10.4-sunxi #20.11.6 SMP Sun Jan 3 21:28:45 CET 2021 armv7l GNU/Linux My "headless" Orange Pi Plus 2 "disappeared from network. I switch it off and connected via serial. I was able to login. Device runs successfully, it is assigning IP to network interface (static assignment) but... there is no connectivity at all (both egress and ingress). [root@PKTEST ~]# ifconfig enx0281cbcd0fcf: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 …

Hi there. I want to use a push button on a GPIO to shutdown O Pi Zero safely. Though the acpid way runs fine on an O Pi One, I wonder if there is a way to make it work on a O Pi Zero. Please direct me if its documented somewhere already. Thanks

that steps must be followed to install kodi in armbian? thnks I have added 'deb http://http.debian.net/debianjessie-backports main' in sources.list and sudo apt-get update & sudo apt-get install kodi but when you start kodi the screen goes black

Hello. Some facts: 1. Boot with image based on legacy kernel cause shutdown after some (less than 10) seconds after power on. 2. Boot with image based on vanilla kernel always ok. 3. If i try to boot without SD card, than power off Cubie with button, then insert SD and switch on with button - it will boot OK with lagacy kernel! Which logs can help to find the problem? I ought to use legacy kernel - i need internal soundcard and both USB. And I see that it is not my own problem - http://forum.armbian.com/index.php/topic/1593-armbian-cubieboard1a10-desktop-with-legacy-kernel-wont-boot-just-shuts-off-cubieboard/- i think we can help to find the bug.

Hi, Please see my comments in the other thread: Essentially when booting a Neo Core using the current air/core mainline image, the onboard fast ethernet is not being initialised. At a guess its because this is not included in the device tree (dtb/dts) for the nano pi air image or in uBoot config - however, if the image is to serve both boards it almost needs to - or they need to be separated. Both are probably reasonable options. Right now i'm trying to understand where the board defs for ethernet are collected during the image build using the armbian build environment and try and get a functional image with fast ethernet for the core…

I got Armbian (Jessie desktop) working on Orange PI PC. I did "sudo apt-get update" and then "sudo apt-get upgrade" and everything was ok until it said "Compiling headers (please wait)." It has now been on this step for a very, very long time. Is it stuck or does this take a ridiculously long time to complete? Should I shut it down and start over or keep waiting? The green light is staying on steady.

Please give me a tip - what is purpose of /dev/mmcblk2boot block devices created? Quite small size - 4MB - ones, do they serve to something u-boot needs at boot time? There are no records for them in fstab so I assume they are created by zram, but what happens to them after boot when they aren't needed anymore? Board Orangepi 3LTS with bookworm minimal Also as a matter of wondering - why there are two zram devices: one of 1/2 of RAM (as usual) and another of quite small 50MB only, what is it for? root@heaven:~# fdisk -l <redacted> Disk /dev/mmcblk2boot0: 4 MiB, 4194304 bytes, 8192 sectors Units: sectors of 1 * 512 = 512 byt…

Hello i've updated the kernel from the legacy to the dev using the procedure To make sure you won’t run into conflicts within newly installed packages, remove them all before upgrade: 1 2 aptitude remove ~nlinux-dtb ~nlinux-u-boot ~nlinux-image ~nlinux-headers aptitude remove ~nlinux-firmware ~narmbian-firmware ~nlinux-$(lsb_release -cs)-root Proceed with install: 1 2 3 4 …

Hi all, Igor: I wanted to say many thank you and congratulate for the awesome job you made with armbian! I have a little big problem: I'm using the BPI-R1 (a.k.a. Lamobo R1 Linux version 4.2.0-sunxi (root@kitchen) (gcc version 4.8.2 (Ubuntu/Linaro 4.8.2-16ubuntu4)) but out of the blue I got the well known problem of the RCP reset to the 1970. I followed the instructions reported here https://github.com/igorpecovnik/lib/issues/111#issuecomment-145634651 but I got some strange issues 1) If I plug my USB keyboard I cannot interrupt the boot process to get a shell before the kernel loads. 2) If I change my boot.cmd and update the boot.scr settings with verbosity=9 an…

Hello guys, i have a orange pi prime. I'm download to https://dl.armbian.com/orangepiprime/Ubuntu_xenial_dev_desktop_nightly.7z this image and i flash to 32 gb sandisk card. System is not opened, i see "starting kernel" message and some controls after it's rebooting continuos. I dont start it. I'm waiting for your helps. King regards

I have tested Armbian with mainline kernel on A10-OLinuxino-Lime-4G board. The only one change is : diff --git a/configuration.sh b/configuration.sh index 7f439a7..be27778 100644 --- a/configuration.sh +++ b/configuration.sh @@ -130,7 +130,7 @@ lime) # Olimex Lime #-------------------------------------------------------------------------------------------------------------------------------- REVISION="1.9" -BOOTCONFIG="A20-OLinuXino-Lime_defconfig" +BOOTCONFIG="A10-OLinuXino-Lime_defconfig" MODULES="hci_uart gpio_sunxi rfcomm hidp bonding spi_sun7i 8021q a20_tp" MODULES_NEXT="" ;; After this patch correct version of U-boot (.config file) is build and correct dtb-…

Hi there, i just wanted to report my experience with Igor Pecovnik's debian 4.1.2 image - especially since he says that I2C is untested with Kernel 4.0 and above. I have a PCTV DVB-C/T2 USB Stick (Triplestick 292e) and could make it work with my Cubietruck. I had to use Igor's compile script from the project website in my ubuntu virtual machine on Windows 7 to get the kernel sources and compile the kernel with the required options (the offered SD-Card image lacks support for I2C Multiplexing). To use this stick, you have to compile the kernel with I2C Multiplexing built in, and build the i2c mux modules for the chipset (I compiled all i2c_mux drivers as modules si…

I am trying to control a relay board on OPI PC plus - armbian. I have used "orangepi_PC_gpio_pyH3" module in python before to control leds, buttons and an 16x2 LCD. This is the relay. To control the Relay module i connected VCC to 5V, GND to ground and IN to PIN 35 (Which is PA10 on my board). and used the code below to open or close the relay just to test but no luck. The code does not return any errors, it runs and finishes but no activity on relay. Both leds (Red and Green) on relay are on when connected. Any help would be appriciated.

Good day. I've purchased lcd 5'inch LCD. I have some troubles with HDMI connection (no image), but i fixed it using this topic: link. (drivers at disk doesnt take any effect) But i can not run touchpad. I used different hints but god no effect board - Orange Pi PC Plus kernel 3.4.113-sun8i module ads7846.ko at /lib/modules/3.4.113-sun8i/kernel/drivers/input/touchscreen My script bin: Spoiler [spi0] spi_used = 1 spi_cs_bitmap = 1 spi_mosi = port:PC00<3><default><default><default> spi_miso = port:PC01<3><default><default><default> spi_sclk = port:PC02<3&g…

Recently i have been experimenting with interrupts on orange pi zero plus2-H3 trying to capture data-ready pulses from an external adc on gpio PA19. The aim is to synchronize spi-read-data transactions with the incoming adc data-ready signal. First I tried to get it to work on legacy kernel 3.4 by adding the following section in to /boot/script.fex and compile the .fex file to .bin file using fex2bin: [gpio_para] gpio_used = 1 gpio_num = 6 .... gpio_pin_6 = port:PA19<0><default><default><1> This configured the pin properly as i had tested on other pins with some leds and it works. The driver code for capturing the interrupt was based o…

Hi everybody, I need some help because I can't make my OPIPlus2e working the way I want. If I understood well I have to install latest armbian, and copy/past script.bin, but sometimes ethernet is not recognized. I tried every distros on my orangepi2e, but I can't install things like kodi (refuses to start, missing libs), or making work hfs drive (can't mount hfs although hfsprogs well installed). I ended up installing openelec and it works great, but I would like to do a NAS with it. Is it still in active development or there is working ISO ? Thank you very much. Best regards, Poukin

Hi igor, when are you going to release the next version (4.1.15) of your debian based image? I wait for it to be able to set up the testing server soon for a new system. Thanks in advance for your contributions and for your efforts Best regards, ireng

HI to all, excuse me but this is my first msg. I have a OPI3 board and I try different OS (Arabian, Ubuntu, Debian) all in different release but I do not have wifi and lan. for wifi I have already try with copy firmware file but is is the same for lan I have in dmesg eth0. UP and DOWN. In my experience I have found only Ubuntu Xenial 4.9.118 on the Orange.org web site with wifi OK. can you help me? Thanks

Hello I wrote aind compile little module only for tests: #include <linux/module.h> #include <linux/sched.h> static int errval = 0; //module_param(errval,int,S_IRWXU); module_param(errval,int,S_IWUSR|S_IRUSR|S_IWGRP|S_IRGRP); MODULE_PARM_DESC(errval,"Value to return from init function"); int my_init_module(void) { printk("errval=%d\n",errval); return errval; } void my_cleanup_module(void) { printk("The module is now unloaded\n"); } module_init(my_init_module); module_exit(my_cleanup_module); MODULE_LICENSE("GPL"); compile by: make -C /lib/modules/6.6.75-current-sunxi64/build M=$(PWD) modules And it cause segmentation fault only…

Hi, I've been using Armbian with Banana Pi M2 for a while and I am very satisfied with performance. Recently I noticed that Teamviewer has been developed for ARM systems, officially only for Raspbian but it seems few people had success running it on Orange Pi too. I followed installation instructions and succeeded however once I connect to it I see only black screen. Did anyone else manage to get it working? Below is link to original thread: https://www.raspberrypi.org/forums/viewtopic.php?f=63&t=144608

Hello After a couple of years, I took my "ancient" OrangePi board and found it working well with Ubuntu 18.04 (kernel 3.14.113). And I even did distr update to 20.04. So HW is ok. I found that Armibian support status of OrangiPi is changed to "Supported" and decided to try the latest image with modern kernel "Armbian_21.02.1_Bananapi_focal_current_5.10.12_desktop.img.xz" (shared image between OrangePi and BananaPi). XFCE desktop was loaded but USB was not working. And that was the known mismatch between OrangePi and BananaPi HW conguration. So I updated "/boot/armbianEnv.txt" with "fdtfile=sun7i-a20-orangepi.dtb". But after that video became OFF…

are the 1-wire modules built into legacy kernel ( 3.4.xx ) with debian jesse on an Olimex A20 LIME2 ( also the -SOM-4GB ) ? To use 1-Wire for DS18b20 temperature sensors on GPIO5 (from my fex file : gpio_pin_5 = port:PG04<0><default><default><default>) I added [w1_para] w1_used = 1 gpio = 5 to the aw_som_a20.fex file but I don't see any 1-wire modules or drivers loaded. I then used fex2bin ( in windows) to get the .bin file, copied it over and replaced the symlink from script.bin that was pointing to lime2.bin to point to my SSM_som.bin ( I changed the name of the edited one to my board name : SSM_som) Would I need to recompile the kernel t…

Hey there, I just build a fresh dev image for the OrangePi One Plus (Stretch, console only, 5.0.x megous sources, latest commit was https://github.com/armbian/build/commit/783c2d0e25ff4542876943cfef6a7ac2921d1262) and unfortunately it seems to be unbootable. I put verbosity to 7 to get some more information rather than being stuck at "Starting kernel..." and this is what came up: Spoiler U-Boot SPL 2019.01-armbian (May 02 2019 - 13:14:43 +0200) DRAM: 1024 MiB Trying to boot from MMC1 NOTICE: BL31: v2.1(debug):9a25f98-dirty NOTICE: BL31: Built : 13:14:40, May 2 2019 NOTICE: BL31: Detected Allwinner H6 SoC (1728) NOTICE: B…

I've built https://github.com/auto3000/RPi.GPIO_NP for the Duo running Armbian Ubuntu test image: cd /sys/class/gpio for i in gpiochip* ; do echo `cat $i/label`: `cat $i/base` ; done 1c20800.pinctrl: 0 1f02c00.pinctrl: 352 Has anyone actually got RPi.GPIO working on Duo? I'm trying to get luma.oled cranking and have SPI working fine, but need GPIO working as well.

After watching a video tutorial on youtube I have attempted to use the build scripts to create a newer image for my Pcduino V2. I had been initially using an image that I found on the archives which uses kernel 4.14, this worked fine for the most part apart from shutting down which would fail 9/10 to shutdown normally. the only way I could ensure that it would shutdown was to do poweroff -f otherwise it just went into a state where most things such as the wifi and usbs would no longer be detected and i was greeted with the message failed to reach target.poweroff. from what I could find out about the issue suggested that it was some kind of issue with systemd, but I could …

A few months ago I dried one of my OPiPC with a 12V power supply and I have not had a chance to try and revive it. So I am looking to migrate the existing 128GB sd card to a OPi Zero. From what I understand, the following would need to be done Mount the SD card (ideally on a linux BOX or VM) Replace script.bin with a suitable file Sync Eject Enjoy Can anyone confirm? Do I need to swap the kernel as well, or is it ok to keep the existing one? As for the script.bin, what's the best way to get one? Download an image and mount it, use fex2bin to generate one? Any help is appreciated. Than…

Hello I'm using my Banana pi Pro as a domitic box with a Zwave Key connected on USB (aeotec Gen5) This morning, unfortunately, I made a apt-get Upgrade which updated the following packages armbian-firmware armbian-tools-jessie base-files bash ca-certificates dbus dbus-x11 e2fslibs e2fsprogs file fonts-opensymbol libc-bin libc-dev-bin libc6 libc6-dev libcairo-gobject2 libcairo2 libcomerr2 libdbus-1-3 libdbus-1-dev libgnutls-deb0-28 libgnutls-openssl27 libgudev-1.0-0 libhogweed2 libmagic1 libnettle4 libpam-modules libpam-modules-bin libpam-runtime libpam-systemd libpam0g libpng12-0 libpng12-dev libreoffice-base-core libreoffice-common lib…

I had to freeze my device on Kernel 6.1.92 & Bullseye to remain operational. Now trying to update/upgrade to Kernel 6.6.nn I run into following probs: 1) Using Armbian-config defreeze and subsequently switch to kernel 6.6.nn works OK 4me, but subsequent apt-get update/upgrade throws me back to kernel 6.1.104. Armbian-config has changed significantly w/ No other Kernel available. 2) Using Armbian-config defreeze, only and going directly to apt-get update/upgrade throws me back to kernel 6.1.104 as well and from Bullseye back to Buster! Its a mess! Will this eventually be corrected and when? RGDS

For some reason the reboot command doesn't appear to reboot the H3. Is this because it doesn't have a PMIC in the same way that the A20's do or is it just a case of the correct assembly instruction not being called?

Will cryptsetup (missing crypto modules), and USB audio (or the onboard analog audio) work on vanilla kernel?

Hi enthusiast, Last few year I used Armbian 5.25, which allow me to echo cpufreq into /sys/devices/system/cpu/cpu0/cpufreq/scaling_***_freq to choose the overclock freq. However, last week, I had to disconnect the power and the Banana Pi didn't boot again. So I decided to install a fresh updated version of Armbian, which is called Bionic. The /proc/version shows: Linux version 4.19.62-sunxi (root@armbian.com) (gcc version 7.4.1 20181213 [linaro-7.4-2019.02 revision 56ec6f6b99cc167ff0c2f8e1a2eed33b1edc85d4] (Linaro GCC 7.4-2019.02)) #5.92 SMP Wed Jul 31 22:07:23 CEST 2019 But now, when I want to overclock by using the method above, it won't al…

Hello all, just joined the forum since this is my first time using Armbian. So I got a NanoPi M1 and the dvp cam500b. From what I understand this camera uses the omnivision ov5640. I am having trouble getting this thing recognized in armbian. I get /dev/video0 to be listed by adding it to /etc/modules, but if I go to access it with any software it reports back 'no such device' or to the similar effect (this includes mjpg-streamer, fswebcam, ffmpeg). Researching around I find many forum posts of people saying one must modify the 'fex' file... to which I found out this is the decompiled version of the /boot/script.bin file using the sunxi-tools/bin2fex. Thing is, wh…

Hello I would like to connect a 3d printer in usb on my cubietruck, except that when I connect it it does not detect the dev port. I do not know what to do. I do not know which USB driver works on the cubietruck. dmesg : [37883.769292] usb 4-1: new full-speed USB device number 4 using ohci-platform [37884.038336] usb 4-1: New USB device found, idVendor=1a86, idProduct=7523 [37884.038354] usb 4-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0 [37884.038365] usb 4-1: Product: USB2.0-Serial on which port dev is connected the printer?

Hi everyone, Since i update to kernel 5.15.25-sunxi , every reboot the mac of wlan0 changed the mac address and router giv him another ip. i will be very happy to solve this issue , Thanks! Note: I tried to re-download the ARMBIAN from the official website, and burned a new SD. This experience did not help. First boot: Second boot:

Today i compiled for my Orange Pi One the kernel 4.11.12-sun8i from the sources. The kernel works with only 1 (one) core. / _ \ _ __ __ _ _ __ __ _ ___ | _ \(_) / _ \ _ __ ___ | | | | '__/ _` | '_ \ / _` |/ _ \ | |_) | | | | | | '_ \ / _ \ | |_| | | | (_| | | | | (_| | __/ | __/| | | |_| | | | | __/ \___/|_| \__,_|_| |_|\__, |\___| |_| |_| \___/|_| |_|\___| |___/ Welcome to ARMBIAN 5.31 stable Debian GNU/Linux 8 (jessie) 4.11.12-sun8i System load: 1.11 0.26 0.09 Up time: 0 min Memory usage: 10 % of 464MB IP: 192.168.3.156 CPU temp: 43°C Usage of /…

Hi, ALL! Have anybody success story with an Armbian and Kodi? With Armbains 5.05...5.10 I installed (apt-get update ; apt-get install kodi) kodi 15.2 from this repository: Quote as described here and allways (in all Armbian releases) has a problems with a sound: sound level very low ans high level noise starting even no video - beginning while kodi GUI started (permanent noise in menus). Film sound also exists while film started playing, but sound level near noise level and very low both (btw, kodi volume regulator not working, only mute mode working in kodi). I watched AC3, MP3, AAC sound coded films - effects are the same: noise with low volume soundtrack. A…

Hi, I'm using the orange pi plus 2e with armbian server installed on eMMC via the built-in script,as the title says i want ways to reduce boot times. I only need ethernet and usb since i will be using it as a "virtualhere" server. Thanks, linux super noob. regards.

I am trying to use gpio without C or Python library, I follow pinout in the wiki : http://wiki.friendlyarm.com/wiki/index.php/NanoPi_NEO_Air 7 GPIOG11 203 modprobe gpio-sunxi echo 203 > /sys/class/gpio/export echo out > /sys/class/gpio/gpio203/direction echo 1 > /sys/class/gpio/gpio203/value LED I connected to Gpio don't light for the moment, I have missed something ? What Linux Gpio may I use ?

Hi, After running the default image with legacy kernel for a few weeks, I am now trying the run a fresh SD card with the latest build of the mainline image. However, the MAC address of my device appears to be changing after each reboot - and I am running about of ideas to fix this issue. What I've tried so far: - Edit script.bin & add MAC address in the [dynamic] section - Edit armbianEnv.txt - Define an address in /etc/network/interfaces So far, I have not been able to solve the problem. Your help is much appreciated. Any suggestions on possible fixes for the issue?

Hi, Initially this started by trying to have proper capture and playback in PCM/I2S port, but it looks like that ALL H3 audio drivers got the same problem, they cannot capture at 24bits, they cannot do HiFi recording despite the Allwinner's datasheet that they do have 24bits in plain audio port and up to 32bits in PCM/I2S/HDMI. I made a very simple test in another thread here and anyone with any H3 board without anything else can do it too -> http://forum.armbian.com/index.php/topic/759-tutorial-i2s-on-orange-pi-h3/?p=17595 Then it popped to my mind to do the most simple of the tests, in the included/onboard audio codec, wich according to datasheet it is w…

uname -a : Linux nanopiair 3.4.113-sun8i #18 SMP PREEMPT Thu Jun 15 02:16:06 CEST 2017 armv7l armv7l armv7l GNU/Linux i installed i2c-tools, libi2c-dev, python-smbus but if i try like this i2cdetect -y 0 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- UU -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 70: -- -- --…

So I have a question... I'd like to manage Li-Ion battery operation on SBCs using the AXP209 power management chip (especially the Banana Pro, as that's what I have...) I soldered a connector to the battery terminals on my BPro for portable operation, and it would be nice to have some kind of solution to raise an alert at low battery charge (like via the onboard LEDs), and automatically call system shutdown at a certain level. Googling has shown that the AXP209 has an i2c interface for sensors, and there are a few scripts for reading battery status here: http://hardware-libre.fr/2014/11/banana-pi-axp209-battery-power-monitoring/ My current plan is to pro…

Dear colleagues, good afternoon. I have 3 problems with the display. I have a orange pi zero. Installed armbian. I set the 2.8-inch display ili9341 spi for instructions, all works very well, but ... expansion of the display - 320x240. But the system is set up as 640x480. Font on the console - Terminus framebufer 6x12. And I am looking for a smaller. Help me please. I want to make the setting expand in the system - 320x240. Font still less. And it passes the wrong color, and I want to make the right color.

Hi guys, I noticed when i switch over to wifi only and turn of the ethernet connection i get issues... ping 192.168.1.12 PING 192.168.1.12 (192.168.1.12): 56 data bytes 64 bytes from 192.168.1.12: icmp_seq=2 ttl=64 time=522.139 ms 64 bytes from 192.168.1.12: icmp_seq=3 ttl=64 time=237.595 ms 64 bytes from 192.168.1.12: icmp_seq=4 ttl=64 time=971.235 ms 64 bytes from 192.168.1.12: icmp_seq=5 ttl=64 time=280.141 ms 64 bytes from 192.168.1.12: icmp_seq=6 ttl=64 time=243.838 ms 64 bytes from 192.168.1.12: icmp_seq=7 ttl=64 time=420.975 ms 64 bytes from 192.168.1.12: icmp_seq=8 ttl=64 time=25.459 ms 64 bytes from 192.168.1.12: icmp_seq=9 ttl=64 time=352.204 ms 64 bytes …

I have done a fresh installation of the Debian image (http://mirror.igorpecovnik.com/Armbian_4.5_Cubietruck_Debian_jessie_4.2.3.zip), but since that the linux does not report any information on power and the battery. There is no information in /sys/class/power_supply. As I am not an linux expert, any useful informationhighly welcome

Hello everybody! Can I read data from the RFID-MFRC522 module with my NanoPi, if so, tell me what python libraries are in Armbian or will it be necessary to install an official ROM and work through RPi.GPIO?

Hey there, I have two questions and one of those may be pretty dumb, but anyway. What is the issue that the onboard network is disabled at the moment? The other question is about the tested 3rd party hardware which include various LAN and WLAN adapters. Have those indeed tested with the current experimental images and working? Or is the network support disabled in the current builds at all? Best regards Werner

My Orange Pi 3 LTS with Armbian 23.11.1 Jammy with Linux 6.1.63-current-sunxi64 is showing high load, but low CPU. The SBC crashed overnight. When I run htop, the following lines show state D: root lscpu root /bin/bash /usr/lib/armbian/armbian-hardware-optimization start root grep -q \<ondemand\> /sys/devices/cpu/cpu0/cpufreq/scaling_available_governors load average: 4.00, 4.00, 4.00 System load: 100% CPU usage: less than 1% sar -u 5 Linux 6.1.63-current-sunxi64 (hostname) 12/31/2023 _aarch64_ (4 CPU) 03:41:54 …

So continuing from this thread since i dont wanna threadjack im facing a simular issue using this image used rufus instead of suse imagewriter since its defunkt on windows 10, have tested the sdcard with 0 errors took about 3 hours to do so since im using a 32gb card for my server. Warning: Only 30418 of 30419 MByte tested. Test finished without errors. You can now delete the test files *.h2w or verify them again. Writing speed: 5.57 MByte/s Reading speed: 8.19 MByte/s H2testw v1.4 So same scenario as the ubuntu distro Found U-Boot script /boot/boot.scr [ bytes read info ] ## Executing script at 43100000 ** File not found /boot/.next ** ** Unrecognized filesystem type…

HI! I have debian wheezy with kernel 3.4.106. When I ran nand-sata-install script, it executed successfully. But after that system doesn't boot from nand. Just black screen. Any help please?

Hello is there any way to stream rtsp on H3 devices? With this i can record video ffmpeg -t 30 -f v4l2 -channel 0 -video_size 1280x720 -i /dev/video0 -pix_fmt nv12 -r 30 -b:v 64k -c:v cedrus264 test.mp4 My hardware is NanoPI neo air + CAM500B. Using friendlyARM's image at the moment because camera don't work on Armbian. (/dev/video0 is there but mjpg-streamer end with errors for example)

Hello! I tried to configure built-in wifi module to work as two wifi interfaces at the same time. I had already configured hostapd+dhcpd at the first interface, at the second interface (...iw add interface...) I could scan my home wifi network (wpa2), but I couldn't connect to it (wrong key). I used utilities to connect like wpa_cli, wpa_supplicant, iwconfig, iw. Did anybody done that, I mean is it possible? What i'm doing wrong?

Hi, i am running armbian stretch on an OrangePi PC with "-dev" kernel and uboot. This was originally an jessie installation with legacy kernel, that was upgraded. I'm wondering now, why the cpu frequency only scales between 648 and 1008 MHz instead of 408 and 1296 MHz. Is this to be expected? cpufrequtils is configured to the latter. # lscpu Architecture: armv7l Byte Order: Little Endian CPU(s): 4 On-line CPU(s) list: 0-3 Thread(s) per core: 1 Core(s) per socket: 4 Socket(s): 1 Model: 5 Model name: ARMv7 Processor rev 5 (v7l) CPU max MHz: 1008,0000 CPU min MHz: …

Hi, Did anybody play with Cedrus on the recent kernels? I'm going to play with it on Bananapi m1, kernel 5.4 and Ubuntu Bionic. Should I just got step-by-step using this instructions http://linux-sunxi.org/Sunxi-Cedrus ? The goal is to evaluate whether this is suitable solution for video surveillnace. I'd used kerberosio with an IP camera for couple years and this does not work good with motion detection.

I have met an ethernet internal error. error log [ 2.003302] Internal error: Oops: 96000004 [#1] SMP [ 2.008184] Modules linked in: [ 2.011243] CPU: 1 PID: 33 Comm: kworker/1:1 Not tainted 4.19.12-sunxi64 #5.68 [ 2.018458] Hardware name: Orange Pi One+ (DT) [ 2.022909] Workqueue: events deferred_probe_work_func [ 2.028045] pstate: 80000005 (Nzcv daif -PAN -UAO) [ 2.032837] pc : sun8i_dwmac_probe+0x16c/0x550 [ 2.037277] lr : sun8i_dwmac_probe+0x21c/0x550 [ 2.041715] sp : ffff000009273b00 [ 2.045027] x29: ffff000009273b00 x28: 0000000000000000 [ 2.050337] x27: ffff000008d9eb30 x26: ffff000008c023a8 [ 2.…

I have a rev 1.4 Orange Pi Zero that overheats. I've confirmed this by touch and know it's a known problem. On the legacy kernel, setting CPU to 800 Mhz and RAM to 300 Mhz used to keep things cool. (e.g. "sudo h3consumption -m 800"). h3consumption doesn't exist on 4.14 kernels, so how do I underclock?

I know I need to find out which drivers to use... I just don't know where to start, I know I've seen some people having success with these displays - ili9488, and a couple others - I just don't know if this fits one of those overlays or not. (nothing I've tried so far has worked). Any help identifying and pointing in the right direction, I would greatly appreciate. Trying to get this to work on my Orange Pi Zero 3 4gb. (uploading images has failed.... so I guess I'll link them?) https://imgur.com/a/NORYCj7 *edit 12/21 - renamed topic since I've Identified the display, going to track my (our?) progress with trying to get it to work…

I'm trying to get an MCP2515 working with an Orange Pi Zero LTS H2+. Everything seems to go well until I try to bring up the can0 interface using the command ip link set can0 up type can bitrate 500000 Once the command is entered, it never returns. Control+C doesn't do help. New SSH sessions fail to start, but pinging the IP address works fine. Trying ifconfig from the serial terminal will also fail to return. Trying to shutdown after the "ip link set..." command, the shutdown procedure takes a long time, and eventually sends [ 4320.026984] systemd-shutdown[1]: Waiting for process: ifdown, wpa_supplicant, NetworkManager, …

So i'm using Orange Pi PC with the latest armbian desktop image. I've noticed this issues: -Booting takes a long time with wifi adapter (realtek 8188etv), stucks at "lsb raise network interfaces" for 2 minutes, than continues -Browsing shares via thunar results in this error -No chrome/midori in repos ?

Hi there I wanted to ask if anybody got HDMI-CEC to work with their Orange Pi Lite. The data sheet says its supported, but I can't get it to work with Armbian. What I tried till now is installing cec-utils with all dependencies and running "cec-client -l", hoping it would work out-of-the-box: root@orangepilite:~# cec-client -l Found devices: NONE Tried different cables and HDMI Ports. CEC is enabled in the TV (Samsung). After a bit of googling (and trying some stuff applying to the RPi) I am now thinking that maybe the kernel hasn't got CEC support compiled in...? root@orangepilite:~# uname -a Linux orangepilite 3.4.112-sun8i #10 SMP PREEMPT Sun Oct 23 16:…

hello after updating from cat /proc/version Linux version 4.14.84-sunxi (root@armbian.com) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #3 SMP Sat Dec 1 07:18:41 CET 2018 to Linux version 4.19.13-sunxi (root@armbian.com) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #5.70 SMP Sat Jan 12 15:43:21 CET 2019 my one wire thermometer stopped working - is there some additional steps needed now? I didn't change my configuration overlays=w1-gpio param_w1_pin=PB10 param_w1_pin_int_pullup=0  and now I have dmesg [ 1174.451457] w1_master_driver w1_bus_master1: Attaching one wire slav…

Hi, https://www.armbian.com/orange-pi-pc2/ states: "Following features should work:" ... "SPI+USB boot" . I was trying to load u-boot from the SPI (but without success). I followed the instructions in u-boot/board/sunxi/README.sunxi64 : $ ./sunxi-fel spiflash-write 0 spl/sunxi-spl.bin $ ./sunxi-fel spiflash-write 32768 u-boot.itb Booting from SPI ends with an exception: U-Boot SPL 2017.09-armbian (Sep 13 2017 - 12:23:18) DRAM: 1024 MiB Trying to boot from sunxi SPI "Synchronous Abort" handler, esr 0x02000000 ELR: 4a000000 LR: 125cc x 0: 000000004a000000 x 1: 0000000000000000 x 2: 0000000000007000 x 3: 000000007…

Hi, I'm still experimenting with different "Linuxes" on that boards.. to get an LCD Display (LVDS) and the Ethernet part working. It cost me days to figure out that there seems to be an ugly glitch. with the stone age "cb2-dvk-sdcard-lubuntu-lcd v1.0.img" I get an working X11 Desktop with 800x480 ..but Ethernet doesn't work. I've checked those fex files (script.bin, script.fex) but couldn't figure out what's going on. I think that doesn't interest someone besides me, ok., got that. Now I've tried the actual "Armbian_community 24.5.0-trunk.667 Jammy with Linux 6.6.31-current-sunxi" that I've downloaded from somewhere here (…

Hi all. In Monday i build new version of Armbian image for Orange Pi One and after this i get next error while loading: Spoiler This image contains newest version of U-Boot (2018.11). My old image build with 2018.05 U-Boot version. Loadin log of old image here: Spoiler This logs made at one PC. I am concerned that in the second case booter find 2 USB devices. but in first case - double number. Anyone can help me with problem. or better write to u-boot support. Or maybe i can build my image with oldest version u-boot...? But i dont known how make this. Thanks.

Hi, do you remember my issue with 2 opi1? Well, today I burned again an armbian image with etcher and connect either of the two opi one, to a usb-ttl converter (an arduino). ok, when I put the power on the result is what you see in the attach... the two freeze on DRAM: always. the power is a xiaomi power adapter 5v2a (double checked with a multimeter) and a handmade cable (checked with the multimeter too, 4.8v/4,9v always) so...can I finally tell that my two board are faulty? or there is something I could do? thank you in advance

[EDIT: The solution to this was realizing I'd been handed Banana Pi's (which have no WiFi), not Banana Pro's (which do have WiFi). I wasted a few days on this.] Hey guys, I'm sure you're sick of hearing this, but I have no WiFi with latest Banana Pi Pro image. No errors in dmesg, lsmod shows "brcmfmac" is present, but no device in iwconfig.

I don't know if this is something I have broken or not, but I have a \var\log and a \var\log.hdd both identical and both being updated. Where should I be looking to rectify this duplication? ARMBIAN 5.25 stable Debian GNU/Linux 8 (jessie) 3.4.113-sun8i OrangePiZero

Why not to add lirc_gpio support to NanoPiNeo Air ? Even if it is not planned, I try to use this patch : https://github.com/igorpecovnik/lib/blob/master/patch/kernel/sun7i-default/0050-lircgpio_and_raw.patch Kernel compilation is ok for me : apt-get -y install git git clone https://github.com/igorpecovnik/lib --depth 1 cp lib/compile.sh . ./compile.sh I try to apply this patch now : ~/crosscompile/lib/patch/kernel/sun7i-default/0050-lircgpio_and_raw.patch I expected to have a lircgpio.ko somewhere, but nothing. Is there a procedure or a tutorial or some help to build a driver ?

Hello, I have a problem with uboot, during its scan of USB buses, it blocks for several tens of seconds, displays an error, then boots. Sometimes it blocks completely and it takes several ON/OFF attempts to get it started. I'm using Nano Pi Core LTS with the mini-shield, I have over 20 and it's happening on all of them. This is what is displayed when it finally starts : U-Boot SPL 2020.10-armbian (Aug 08 2021 - 15:18:24 +0200) DRAM: 512 MiB Trying to boot from MMC1 U-Boot 2020.10-armbian (Aug 08 2021 - 15:18:24 +0200) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: FriendlyARM NanoPi NEO DRAM: 512 MiB MMC: mmc@1c0f000: 0, mmc@1c11000: 1 Loa…

Hi I own since a while an Orange Pi One Plus board that I have been unable to use till now (OS images supplied by manufacturer are just a joke !). I wanted to give it a test with ARMBian as you offer now some Beta images. As both Bionic and Stretcher are offered, is there one of them more stable or more near something finished ? Did someone have tried the board with one of these ? and did it work ? Thanks Vincèn

Well it took me longer than i hoped but i have managed to forward port icenowys code for TVE on the H2+/H3 to mainline armbian. It seems to work totally fine, with a few caveats. First: Sample images of it in action -> https://imgur.com/a/vXQEM Second: the patch itself -> https://github.com/stevenj/h3-tve/tree/v0.0.11 Third a prebuilt image for Orange Pi Zero: -> https://github.com/stevenj/h3-tve/releases/tag/v0.0.11 Howto: just put the patch into userpatches for the sunxi-next kernel, and build. it should apply cleanly. Its for H2+/H3. I have only tried it on a orange pi zero, but it should work on all H2+/H3 boards. …

Hello all, I'm going to preface by saying that I am not experienced with Pi, Pi clones, or linux, but I know how to google stuff until my fingers bleed and can navigate around a terminal window well enough. I have an Orange Pi Lite, which is running OctoPrint primarily, but does use a few other uses. I am using a prepared Armbian image file. Upon SSH login in the terminal displays the following: Welcome to ARMBIAN Debian GNU/Linux 8 (jessie) 3.4.113-sun8i System load: 3.17 Up time: 39 min Memory usage: 72 % of 494Mb IP: 192.168.0.250 CPU temp: 36°C Usage of /: 99% of 3.6G storage/: 1% of 3.8G CPU is a…

Hello Still I could not resolve network problems with orange pi plus. My configuration: Orange pi plus with heatsink, (image Armbian_5.05_Orangepiplus_Debian_jessie_3.4.110), external USB drive(partition ext4). Main problem - when copying large file into samba share network hangs on orangepi board. CPU temperature not exceed 50C when copying. Leds blinking near ethernet cable but ping from cli works only on local ip. Same situation with other orange pi images (debian, lubuntu and ect...) Please help

I am trying to use fbtft on the Orange Pi Zero, seems broken. Looks like an issue with the SPI driver itself. My skills are not enough to debug this. I am doing something like this: modprobe fbtft_device custom name=fb_ili9340 gpios=dc:3,reset:0 speed=32000000 busnum=1 rotate=90 The LCD functions but stops updating after a couple of mins. Linux is still running but dmesg shows a crash. Login shows "ARMBIAN 5.31 stable Ubuntu 16.04.3 LTS 3.4.113-sun8i" root@orangepizero:~# uname -a Linux orangepizero 3.4.113-sun8i #18 SMP PREEMPT Thu Jun 15 02:16:06 CEST 2017 armv7l armv7l armv7l GNU/Linux It is not …