Allwinner sunxi

I have an orange pi zero that I'm going to use as a pi hole. When installing pi hole, I received a "Error: Unable to update package cache. Please try "sudo apt update"." I did just that and received another error stating Err:1 https://ports.ubuntu.com focal InRelease Could not connect to ports.ubuntu.com:443 (2620:2d:4000:1::19). - connect (111: Connection refused) Could not connect to ports.ubuntu.com:443 (185.125.190.39). - connect (111: Connection refused) Could not connect to ports.ubuntu.com:443 (2620:2d:4000:1::16). - connect (111: Connection refused) Could not connect to ports.ubuntu.com:443 (185.125.190.36). - connect (111: Connection refused) Er…

Hi there, after upgrade Armbian today the Device (banana-pi) doesnt come up again telling that the root fs couldnt be mount because mmcblk0p1 is not available. After checking SD Card everything seems ok, filesystem is there and doesnt have any error. But still no boot. Then after applying a backup things are fine again. Started the upgrade again and same error like before. When applying those two updates there is repeatedly a dead system afterwards. Tested on different devices now. root@gluster01:~# apt list --upgradable Listing... Done armbian-config/unknown 25.5.0-trunk.330.0402.205255 all [upgradable from: 25.5.0-trunk.286.0324.065110] linux-ima…

I installed Armbian 4.5 Debian Jessie 3.4.109 and added XFCE desktop, but there is no audio on 3.5 jack (I cannot test HDMI audio output). I built my own Debian Jessie 3.4.109 selecting Banana Pro and including XFCE desktop without any other change, and also in this case there is no audio on 3.5 jack. Some useful information to solve the problem. These are equals on both installation. root@bananapipro:~# cat /proc/asound/cards 0 [sunxicodec ]: sunxi-CODEC - sunxi-CODEC sunxi-CODEC Audio Codec root@bananapipro:~# cat /proc/asound/devices 2: [ 0- 0]: digital audio playback 3: [ 0- 0]: digital audio capture 4: [ 0] : control 33: …

I run a cubietruck with armbian jessie/legacy-kernel. I used it as a owncloud- and tvheadend-server. For the tvheadend-server i use 2 DVB-S2-USB-devices (TeVii S660 USB). I had problems woith one of them and want to replace one of them with a Technotrend TT-connect S2-4600. I could not compile the needed driver, so I tried to use the vanilla-kernel, because the newer kernel has support for this DVB-card. I could use the Technotrend-device with vanilla. But both devices stutters when displaying or recording a stream. Is this a known problem? When switching back to legacy, the old Tevii-device runs smooth again, but there is no support for Technotrend. What can I d…

I'm trying to get audio out work on Orange Pi Lite using HDMI. aplay -l lists sndhdmi as card #1 and I have set it up as default in ~/.asoundrc. aplay -v shows it being used, but my AV receiver doesn't recognise the Pi nor output any sound. The same cable & receiver works fine with e.g. Macbook Pro. Should the HDMI audio output work in the legacy Jessie server image for OPi Lite? If yes, how could I debug more why it doesn't seem to work?

Hi, I have a mainline installation of Armbian (Debian) on my banana pi on which I want to control a display from within java. Version of the kernel: Linux bananapi 4.11.6-sunxi #6 SMP Fri Jun 23 19:56:18 CEST 2017 armv7l GNU/Linux The connections I use are as followed: LCD Python lib PI4J WR 23 4 RD N.U. N.U. DC 24 5 CS N.U. N.U. RESET 25 6 …

[ 10.900422] libphy: 1c30000.ethernet: probed [ 10.921452] Generic PHY 1c30000.ethernet-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=1c30000.ethernet-0:01, irq=-1) [ 10.921469] sun8i-emac 1c30000.ethernet: device MAC address slot 0 a2:3f:fc:36:c5:70 [ 10.923862] sun8i-emac 1c30000.ethernet: device MAC address slot 1 33:33:00:00:00:01 [ 10.923953] sun8i-emac 1c30000.ethernet: device MAC address slot 1 33:33:00:00:00:01 [ 10.923958] sun8i-emac 1c30000.ethernet: device MAC address slot 2 01:00:5e:00:00:01 [ 10.923972] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 11.216443] random: crng init done [ 13.040824] sun8i-emac 1c30000.ethernet …

I have a problem with annoying randomly flickering cursor in armbian 5.34.171102 ubuntu desktop with mainline kernel. It's plain system after instalation, just chromium browser opened. The legacy kernel is OK on my board Orange pi plus 2e. Any idea what might cause this<

HowTo: Setting up resolution 1600x900 & 1366x768 ? &how can i set up other resolutions those are not in h3disp like 1600x900 board is orangepi-pc

Hello all, The board has a 2MB NOR FLASH chip what would be enough for storing u-boot and booting the system over network. Unfortunately u-boot says there is no ethernet. Is there anybody who knows how to enable ethernet on this or similar board like OPi PC2 or Nanopi NEO2? Is it just a matter of configuration or is RTL8211E as PHY generally not supported on H5 chips? Thank you very much for your help. --DieHackbeere

Let's say I'm deploying hundreds of warehoused devices employing an H5-based Orange Pi Zero Plus, and I need a reliable distinct identifier for each. In another application we're using the MAC address, but that seems not to be EEPROM-ed on the OPiZ+. So, okay, SOC Unique ID has been mentioned elsewhere (MAC generation on the OPiZ+), but where is it available? cat /proc/cpuinfo does not include "Serial". lshw has a "serial" but I'm not sure that's reliable (I've got a Beaglebone that doesn't show one - and it says /proc/cpuinfo Serial: 00000000). So what's a good low-cost (i.e. not by launching Perl scripts) way to obtain the unique CPU identifie…

Hi guys, In order to increase the CPU frequency on my Orange Pi Zero Plus I need to run the 4.17y kernel: I downloaded the prebuilt image from armbian which only includes the 4.14y kernel. Is there any way to download the newer 4.17y kernel, rather than having to build Armbian from scratch? Sorry if this is a newbie question but I'm not a linux expert. I appreciate any help in advance

Hi all, i have orangepione uname -a Linux orangepione 4.19.20-sunxi #5.75 SMP Sat Feb 9 19:02:47 CET 2019 armv7l GNU/Linux And i try create hid gadget keyboard. I find topics about raspi zero, orange pi zero, and i use config from where. So i can create keyboard, and when i connect it to linux or windows machine i can see symbols, but when i try send key to macbook bios i have no luck. Did anybody know how to get work with macbook? /etc/modules dwc2 libcomposite /etc/rc.local /usr/bin/isticktoit_usb exit 0 alex@orangepione:~$ cat /usr/bin/isticktoit_usb #!/bin/bash sleep 10 # Create gadget mkdir /sys/kernel/config/usb_gadget…

Device: Orange Pi +2e. Builds 20.20, 20.05, 20.08 The Armbian Boot Logo is shown only when we boot from SD Card. Do nand-sata-install to eMMC and boot from eMMC, the logo disappears. Could this be a timing issue as it boots faster on eMMC? I do not see any flicker or flash during u-boot. --Rajesh

My third Orange Pi Zero came last week, yesterday I plugged it and had heating issues... So I started reading, learning and testing.... Setup: OPiZ-1: 256 MB, no SPI flash - Has extension board plugged - for comparison OPiZ-2: 512 MB, with SPI flash OPiZ-3: 256 MB, with SPI flash (new one with problem) Test conditions: All with (newish) Sandisk Ultra 16 GB Class 10 All new formatted (SD Formatter) and burned/validated (Etcher v1.0.0) with Armbian_5.25_Orangepizero_Debian_jessie_default_3.4.113.img All on my desk - side by side, ambient temperature 25.0-25.1 C (20 cm from boards, no air flow) No case, no passive/ac…

Hello guys, there is a question, is there an EDK2(tianocore) for orange pi 3 lts? If yes, how can it be compiled? Maybe there are projects to run uefi operating systems for arm on orange pi.

Hi. After 2 years uptime it disconnected from wifi and was unable to reconnect even after reboot. I suspect my AC adapter has degraded. Can this SBC measure the voltage? Upd: saw this post: https://raspberrypi.stackexchange.com/questions/112122/wifi-not-connecting-depending-on-power-supply I use NetworkManager and when it starts it usually cannot connect to wifi saying that the pre-shared key is wrong, marking the connection as failed and not re-trying. In particular, the log contained a failed "asking for new key" message. Re-starting the service or manually activating the connection worked. As a workaround I created a *.conf file in …

Hi all, i'm trying compile 3.4.*, i used normal way - i downloaded scripts to manage it, i'm successful with compilation but my issue is that i want to connect relay to banana pi J12 (DIP8) pin 5 which should be PH3 on A20 and that relay should be connected in parallel to switch button on PC ... so it means each switch (even fast) of the level can start turn off pc :-( so my issue is that uboot default configs for banana pi is having irrelevant configuration of pins that are prepared on connectors to be used as GPIO ... for example PH3 and PH5 at banana pi's J12 are not related to VBUS of USB as it's written in configs and fex, please somebody could tak…

Here my changes over the script.fex file to achieve compatibility with the 15.6FHD LCD display [disp_init] disp_init_enable = 1 disp_mode = 0 screen0_output_type = 1 screen0_output_mode = 4 screen1_output_type = 0 screen1_output_mode = 4 fb0_width = 1920 fb0_height = 1080 fb0_framebuffer_num = 2 fb0_format = 10 fb0_pixel_sequence = 0 fb0_scaler_mode_enable = 1 fb1_width = 1024 fb1_height = 600 fb1_framebuffer_num = 2 fb1_format = 10 fb1_pixel_sequence = 0 fb1_scaler_mode_enable = 0 lcd0_backlight = 0 lcd1_backlight = 197 lcd0_bright = 50 lcd0_contrast = 50 lcd0_saturation = 57 lcd0_hue = 50 lcd1_bright = 239 lcd1_contrast = 50 lcd1_saturation = 57 lcd1_hue = 50 [lcd0…

My cubietruck mac address which I am assuming is auto generated is invalid. Though one would think it should work, other software on routers will not accept the mac as valid, and thus I can not add configurations to it. We probably need a layer somewhere to create 'valid' mac addresses. 02:C2:07:C0:B7:C7 is the generated mac that my cubietruck is currently using which software claims is invalid.

Hello, I do images of Debian Jessie with Desktop anf in the end it do image but I have : [ o.k. ] Installing desktop-extras for sunxi [ sunxi ] E: Impossible de trouver le paquet libdri2-1 dpkg: des problèmes de dépendances empêchent la configuration de mpv : mpv dépend de libbs2b0 ; cependant : Le paquet libbs2b0 n'est pas installé. mpv dépend de libcdio-cdda1 (>= 0.83) ; cependant : Le paquet libcdio-cdda1 n'est pas installé. mpv dépend de libcdio-paranoia1 (>= 0.83) ; cependant : Le paquet libcdio-paranoia1 n'est pas installé. mpv dépend de libfdk-aac0 (>= 0.1.1) ; cependant : Le paquet libfdk-aac0 n'est pas installé. mpv dépen…

Hi guys, first I want to thank you for your marvelous work. I've learned much... I've ordered a Nano Pi Neo Air and two Nano Pi Neo from Friendly Arm which arrived last week to build some squeezelite clients and drop them around the house. At the moment I'm just using some cheap USB-C-Media Soundcards but plan to invest in better ones, if the multi-room solution I have in mind is used enough. The Nano Pi Neo (not Air) does exactly what it should using the Ubnuntu Xenial Image from the download page. Cheers! For the Air's I've used the Debian release, don't know really why ;-) At first I've bootet it from a SD-Card after a direct eMMC-Flash using https:…

I was wondering if there is a significant performance difference with the lime2 when a heatsink is added? I plan on ordering a couple of heatsinks from ebay to try myself however I'm wondering if anyone from the community has any feedback. Thanks

After creating my own initramfs using this command from a chroot-ed environment sudo update-initramfs -t -u -k `uname -r` And rebooting, I get the following error: Found U-Boot script /boot/boot.scr 3708 bytes read in 126 ms (28.3 KiB/s) ## Executing script at 43100000 U-boot loaded from eMMC or secondary SD Boot script loaded from mmc 202 bytes read in 80 ms (2 KiB/s) 5731772 bytes read in 668 ms (8.2 MiB/s) 6790944 bytes read in 759 ms (8.5 MiB/s) Found legacy kernel configuration ** File not found /boot/script.bin ** ## Loading init Ramdisk from Legacy Image at 43300000 ... Image Name: uInitrd Image Type: ARM Linux RAMDisk Image (gzip compre…

I am running cubitruck wheezy 7.5 from 2014, Kernel 3.4.104 for over three years as homeserver with VGA display. How can I activate HDMI for a new display. (I cannot reinsall the whole system, growed up for all the years) I already changed the settings in fexfile: [disp_init] disp_init_enable = 1 disp_mode = 0 screen0_output_type = 3 screen0_output_mode = 6 screen1_output_type = 3 screen1_output_mode = 6 also changed fex to bin and reboot, but no HDMI-output Can anybode give me a hint?

Hi - Just checked out latest greatest code from git to compile new stretch image for my NanoPiNeo2 ( Armbian_5.46_Nanopineo2_Debian_stretch_next_4.14.47 ) but seems it won't boot up. Tried two SDcards and two different boards but same result. Tried both Etscher ( 1.4.4 ) and Rufus ( 3 ) but same result, any issue known that I missed ? Please note I am building a standard image ( thus no customised settings ) also came to my attention the board becomes quite warm, this is unusual . Thanks

Hi all, I'm interested in running canbus on Banana Pi (A20). I have problem with setup canbus. Some info about system: ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.18-sunxi in armbian-config -> System -> Hardware only "can" is enable and MCP2551 transreciver is connected to can rx/tx banana pinout. lsmod | grep can: root@bananapi:~# lsmod | grep can can_bcm 24576 0 can_raw 20480 1 can 20480 2 can_raw,can_bcm sun4i_can 16384 0 can_dev 20480 1 sun4i_can Next setup interface: ip link set can0 type can bitrate 125000 restart-ms 10…

Hello everyone. My OP-PC is dead, with NO HDMI signal, NO console output, NO network output (LEDs off), only 1 LED is on which indicates SD card inserted (if SD card removes, it off). when use newly created SD card with Armbian, SDcard OS partition not resized. when connect to power supply, I can hear current noise. before it dies, it runs armbian server image with mainline kernel (4.14), it doesn't look like thermal fail, due to it runs very well during summer. I guess it is shorted some place, but I can't find where! so which hardware test point could I use to detects hardware failurtes.

Is there a way to run netflix yet? Does Chromium run well and able to run netflix? Appears this doesn't matter, because Chromium doesn't work with netflix anymore... Does anyone know if chromium OS works well with OPi PC otherwise? Basically I want it to work for netflix, I also want to connect it to a printer, and the ability to run NordVPN and a torrent client would be a bonus as well.

Upgraded kernel on existing working project and g_ether no longer working. So did fresh install on formatted card of Armbian_5.75_Orangepizeroplus2-h5_Ubuntu_bionic_next_4.19.20 If I do modprobe g_ether and then dmesg, I get the following udc-core: couldn't find an available UDC - added [g_ether] to list of pending drivers Is there something new in 4.19.20 that I must do? It used to work in older releases from 9 months ago or so...

Hi All , i just tried stretch and buster there is a problem with PA10 configured "IN" problem seems to be on kernel > 4 old method for GPIO works perfectly , i have read that FEX is no longer availlable on 4.X kernel . PA10 il also used by SPI ( pin 1) . SPI is not enable on /boot/ArmbianEnv.txt. this script works perfectly on 3.x kernel but crashed GPIO 10 and GPIO 7 on 4.x kernel , when PA10 configured in "INPUT" and receive a +3.3V it crashed and seems to stay up indefinitively nothink on logs , PA7 can't become up in OUT mode i think there is a problem with SPI and GPIO on 4.X kernel I can't change GPIO pin on my pr…

Here is uploaded image showing problem with text overlapping. I googled without success, so if anyone could suggest how to try fixing it. Chromium version is 76.0.3809.100 (Official Build) Built on Ubuntu, running on Ubuntu 16.04 (32-bit) on Orange Pi Lite. It is not big deal, but if there is easy fix why not to try.

I had successfully installed Armbian_2022.08.8_Bananapi_bullseye_CLI_5.15.74 on my M1 and copied the system to an SSD which I had attached to the SATA port. Then I had updated the UUID in armbianEnv.txt and running the system from SSD was working fine. The system was running headless in my closet for about 2 months, and I even had no problems to remotely restart the device until today, when it did not come back up after a reboot. I took it from the closed and hooked it to a monitor just to see the following error messages: ** Bad device specification mmc 0 ** Couldn't find partition mmc 0 I suspected a broken SD card but a check on my Ubuntu de…

I'm using Armbian 23.02 Bullseye CLI. I didn't want the HDMI to show the boot system log and TTY1 login screen. According to the armbian documentation, I changed "console=both" to "console=serial" in /boot/armbianEnv.txt. I checked /boot/boot.cmd related to console, and I confirmed that this modification is OK, but it cannot start, uboot printed "Starting kernel..." After that, there is no output, and the power supply is only 5V 170mA. The following is the printing of the serial port. If anyone has been in a similar situation, please give me a little help, thank you very much. U-Boot SPL 2022.07-armbian (Feb 17 2023 - 22:32:08 +0000) DRAM: 2048 MiB Trying …

I have question. OZPI v3 has support for hardware DS18B20 thermal sensor via w1-gpio ? In armbian-config when we got to the “system” section and select “Hardware” is not existing w1-gpio or OZPI v3 has not support for w1-gpio hardware ? Does not work because there is no device tree file (in the /boot/dtb/allwinner/) and we need to create it ??? like for OZPI v2 ?: 1. Create text file "sun50i-h616-w1-gpio.dts" /dts-v1/; / { compatible = "xunlong,orangepi-zero2\0allwinner,sun50i-h616"; fragment@0 { target = <0xffffffff>; …

Hi, I've build an SD card image with in a buildroot myself, used the stable branch as suggested. "For stable branch use --branch=v23.11"..and that all worked good so far. I'm no linux guy at all and begun some investigations, installed packages and configured the system, this was an desktop variant with xfce. Somewhere in the middle of work I've got the message that a security update is available and I should do an apt upgrade..done that. Interresting for me was, that I've got an Update to Armbian 24.2.1 jammy.. ok ..then this is so. I've noticed later that I don't have any video output from X11 anymore, after the login prompt the sc…

I just booted the NanoPi Neo2 with the latest "Server images with Armbian Linux v6.6" running Ubuntu 24.04 (Noble). After logging in via SSH, I saw a message stating that this image is for development use only and not for production. Based on your experience, how stable is the development image? Am I correct in understanding that there is no stable image for NanoPi Neo 2 ?

I need to make custom intro on my bigtreetech cb1 when i try plymouth some time give me error and sometimes the system startup normally as normal Plymouth without pics only 3dots in middle of screen i want examples or guidelines to make it and when i make update to initremfs files it’s give me error such as error to create hard link what I should i do

Hi igor, when are you going to release the next version (4.1.15) of your debian based image? I wait for it to be able to set up the testing server soon for a new system. Thanks in advance for your contributions and for your efforts Best regards, ireng

Hi Igor and all, after running armbian on my A20 lime2 for a long time, I decided to switch to armbian on my A10 lime, too (from jessie with a eewiki-based self-compiled kernel). So far it works as perfect as the A20, but there are two small and funny things with the Armbian_5.00_Lime-a10_Debian_jessie_3.4.110.zip image I used: After login the nice armbian banner stated that my A10 lime is a cubieboard . I have a cubieboard, too. So I double checked... The problem is located in /etc/init.d/armhwinfo, There all "sun4i" boards are simply "Cubieboard". I had to adapt the LED check which is used to detect Lime and Lime2 a bit and added the Lime A10. I ch…

Hi all, I upgraded my jessie 5.05 desktop version for Orange Pi PC via "apt-get upgrade" to 5.10 without any issues. Now I noticed that the green status LED blinks twice every ~0.5s after first reboot. Can anyone figure out the meaning of this?? Thanks in advance.

I use OPI - ONE. I upgraded a package. The CPU temperature become so hot. Welcome to ARMBIAN Debian GNU/Linux 8 (jessie) 3.4.112-sun8i System load: 0.29 Up time: 7 min Memory usage: 11 % of 494Mb IP: 192.168.10.112 192.168.10.116 CPU temp: 60°C Usage of /: 18% of 7.2G Last login: Tue Aug 2 16:42:15 2016 from 192.168.10.101 orangepi@orangepione:~$ cat /etc/armbian-release # PLEASE DO NOT EDIT THIS FILE BOARD=orangepione BOARD_NAME="Orange Pi One" VERSION=5.16 LINUXFAMILY=sun8i BRANCH=default ARCH=arm orangepi@orangepione:~$ cat /sys/devices/virtual/thermal/thermal_zone0/temp 59 orangepi@orangepione:~…

when i triaing change monitor in NANO PI M1 from HDMI to DVI ( H3disp 1080p ), then i cannot start system in a DVI monitor. After changed HDMI monitor is also blocked. Then you have to delete into another computer in sd card your scirpt bin file and rename script.bin.back to script.bin to return to HDMI monitor. DVI does not work at all . maybe it is producer error not software.

Hi all. I've got an issue trying to use Bluetooth and RFCOMM. My system is: Cubieboard2 running latest img and updated with apt-get update/upgrade: ____ _ _ _ _ ____ / ___| _| |__ (_) ___| |__ ___ __ _ _ __ __| | |___ \ | | | | | | '_ \| |/ _ \ '_ \ / _ \ / _` | '__/ _` | __) | | |__| |_| | |_) | | __/ |_) | (_) | (_| | | | (_| | / __/ \____\__,_|_.__/|_|\___|_.__/ \___/ \__,_|_| \__,_| |_____| Welcome to ARMBIAN 5.25 stable Debian GNU/Linux 8 (jessie) 4.9.12-sunxi System load: 0.07 Up time: 30 min Me…

I'm sorry for the lame question, I just don't wanna regret anything before buying this fan, so I'm talking about this fan (3cm x 3cm) Spoiler I want to mount this fan right below the board by just screwing it in. Do the holes fit perfectly with the holes of the opiz board ? I've asked this before on facebook but someone suggested me to just glue the fan directly onto the board but I'm afraid it'll damage the board instead.

[Apologies. There seem to be a number of posting close to this subject. Trying to get a definitive view] So, with the 3.4.113 kernel the gc2035 driver fails when trying to identify the sensor. The problem lies in the sensor_init function where a read of the I2C/CCI bus fails. Before I break out the breakout board can anyone verify these basics please? I've tried the various suggestions for setting one of the GPIO pins prior to loading the modules but to no avail. Cable, blue insulation on top side of the expansion board FPC, blue insulation facing up towards SD card on the OPI one. FEX as below. [csi0] vip_used = 1 vip…

Hello guys, I trying to make my ili9431 to show early stage of boot console. Everything works great if I load from /etc/modprobe.d/fb_ili9341.conf but if I load from armbianEnv.txt nothings happen. I suspect that I am trying to load the device before the driver is loaded. I read about "platform file" here: https://github.com/notro/fbtft/wiki/Boot-console but I have difficulties modifying the files because the guide is for RPI. Can someone guide me or at least to know if I'm on the right track? Hardware details: Device: Orange PI Zero Plus2 Kernel: Linux orangepizeroplus2 4.14.83-sunxi …

I just installed the latest Ubuntu Bionic Image with 4.x kernel, fully updated and upgraded. On Orange Pi Zero 1.4 512MB + IO expansion kit board Armbian 5.75 Ubuntu 18.04.2 LTS Linux orangepizero 4.19.20-sunxi #5.75 SMP Sat Feb 9 19:02:47 CET 2019 armv7l armv7l armv7l GNU/Linux `cat /proc/asound/cards` "No sound cards" In armbian-config, I enabled analog-codec, `update-initramfs, rebooted, but there's still no sound card. mocp complains there is no driver. speaker-test (starts like this) Playback device is default Stream parameters are 48000Hz, S16_LE, 1 channels Using 16 octaves of pink noise ALSA lib conf…

Hello all, Recently, I bought an Orange Pi Win Plus board and have installed Armbian on SDcard and it works fine but when i try to install it on emmc using "sudo nand-sata-install" it just shows "install/update the bootloader on SD/eMMC" in the options instead of "boot from eMMC - system on eMMC" as i have seen on the internet . so guys! what am i doing wrong!? Regards,

I had got a OrangePI One Plus (H6) on a few day ago. I had a problem with HDMI to VGA Converter that it do not work with my OrangePI One Plus. I guess it maybe about the Power of that HDMI on OrangePI One Plus was not enough for HDMI to VGA Converter's operation. Then I fix it by replace regular HDMI to VGA to be HDMI to VGA with 5V external port. And Yeah, it's work fine!!! but I had OrangePI One (H3), OrangePI PC2(H5) and OrangePI Prime(A64) too which All of them had no problem with HDMI to VGA Converter. I feel wonder with this problem on OrangePI One Plus.

I would like to set a GPIO to output-high during the boot. In this case, the GPIO is PG0 whose number is 192. The device tree overlay is /dts-v1/; /plugin/; / { compatible = "allwinner,sun50i-a64"; fragment@0 { target = <&pio>; __overlay__ { gpio_out_override_hog { gpio-hog; gpios = <192 0>; /* PG0 */ output-high; line-name = "PG0-gpio-hog"; }; }; }; }; However, after the application and reboot, I do not see any init information in "/sys/kernel/gpio" about GPIO 192. There is no "/sys/class/gpio/gpio192" folder existed after boot either. Is there anything wrong in the overlay file?

I'm trying to setup a GPS-based time server on an Orange PI Zero 3, running Armbian 24.8.0-trunk.495, kernel 6.6.43-current-sunxi64. I have the exact same hardware setup working fine on a RaspberryPI 4b, running RPI OS / Debian 11 (bullseye) , kernel 6.1.21-v8+ #1642. On the RPI4, gpsd recognises the (cheap chinese "M8N") GPS module as u-blox and keeps working in a stable way root@rpi4:~# gpsctl /dev/ttyS0 /dev/ttyS0 identified as a u-blox SW ROM CORE 3.01 (107888),HW 00080000 at 9600 baud. the /boot/config.txt has these two lines for the UART config enable_uart=1 init_uart_baud=9600 On the OPIZ3 I configured /boot/armbianEnv.txt for UART5…

hello Igor, I get some error information after updating the new kernel v4.1 root@cubie:~/3.4.108# dpkg -i linux-image*.deb (Reading database ... 70156 files and directories currently installed.) Unpacking linux-image-cubietruck (from linux-image-cubietruck_4.1_armhf.deb) ... dpkg: error processing linux-image-cubietruck_4.1_armhf.deb (--install): trying to overwrite '/lib/modules/3.4.108-cubietruck/modules.builtin.bin', which is also in package linux-image-3.4.108-cubietruck 4.0 dpkg-deb: error: subprocess paste was killed by signal (Broken pipe) Errors were encountered while processing: linux-image-cubietruck_4.1_armhf.deb how to solve this. Best regards Fla…

Dears, I have done the last update. I lost dkms, and when trying to recompile/reinstall it, I started get strange errors. It seems binaries in linux-headers are compiled for Intel. I would even the kernel is configure for Intel. Was not able to compile the module actually. Was there some mishap? Rui

Hello, JiveLite would be nice for LMS-installation with Touchscreen/Display. http://forums.slimdevices.com/showthread.php?98156-Announce-JiveLite-cut-down-squeezebox-control-application Has anyone of you ever successfully compiled JiveLite? TIA Jochen P.s.: With a little help from google translator. Edit: Well, I did it!

Orange Pi Lite - Armbian 5.14 The desktop shutdown (or shutdown -h now) shuts down the desktop, the system starts shutting down, then the desktop starts again, then disappears and the system shuts down. Its not a disastrous problem, but just annoying. I've traced it to the fact that 'nodm' is seeing the desktop stop, and then restarting it. Apparently either 'nodm' isn't getting the shutdown signal, or ignoring it, or getting it too late. Any guidance on what 'nodm' config, or some other config might help me to fix this? /K

Hello, I have NanoPi Neo and I cannot make ds18b20 to work, it does not show in the devices folder. On armbianmonitor it writes: http://sprunge.us/fdjC On lsmod: Module Size Used by sunxi_cir 1601 0 w1_therm 2498 0 wire 18294 1 w1_therm gpio_sunxi 8269 0

I'm trying to figure out why Firefox-esr crashes form time to time on my Olinuxino-Lime A20. I also have a Banana PI (also A20) and on that board Firefox never crashes. On both boards I use the legacy kernel, and I use uBlock adblocker on both boards. The Olinuxino has 512 MB RAM and the Banana Pi 1 GB. Googling around I found out that crashreports could be viewed on "about:crashes" or on ~/.mozilla/firefox/crashes. However, there is no such file. Do youi have any suggestions on where to find crashreports? Thanks in advance and much appreciation for your continuous work on the Armbian distribution!

Hi guys, I noticed when i switch over to wifi only and turn of the ethernet connection i get issues... ping 192.168.1.12 PING 192.168.1.12 (192.168.1.12): 56 data bytes 64 bytes from 192.168.1.12: icmp_seq=2 ttl=64 time=522.139 ms 64 bytes from 192.168.1.12: icmp_seq=3 ttl=64 time=237.595 ms 64 bytes from 192.168.1.12: icmp_seq=4 ttl=64 time=971.235 ms 64 bytes from 192.168.1.12: icmp_seq=5 ttl=64 time=280.141 ms 64 bytes from 192.168.1.12: icmp_seq=6 ttl=64 time=243.838 ms 64 bytes from 192.168.1.12: icmp_seq=7 ttl=64 time=420.975 ms 64 bytes from 192.168.1.12: icmp_seq=8 ttl=64 time=25.459 ms 64 bytes from 192.168.1.12: icmp_seq=9 ttl=64 time=352.204 ms 64 bytes …

My Orange Pi Lite + octoprint often freeze during a print. I noticed that when it happens I can not access either the web panel nor in ssh. I believe that it detaches from wifi and go into freeze. I have already ruled out power supply problems and overheating. Someone can help me?My image is: Armbian_5.25_Orangepilite_Ubuntu_xenial. Here is a screenshot of the statistics: Thanks!

Just got my orange pi up and running with armbian jesse and the wifi is working but there is no web browser. I want to install mozilla firefox. I have the latest version on the orange pi but dont know how to install it. any help would be appreciated. I am running the xfce4 desktop. I get a cannot execute binary file: Exec format error when i try to run it

Hi gurus! I'm trying to connect gc2035 camera to my OrangePi One, it's marked as SH-2035 at the cable. It is old problem, as I understand reading forum, but nothing to help me. I'm new Linux user and use Armbian 5.31, Linux orangepione 3.4.113-sun8i #18 SMP PREEMPT Thu Jun 15 02:16:06 CEST 2017 armv7l armv7l armv7l GNU/Linux. That camera works with Armbian 5.20, but I don't want to do downgrade. As I understand it needs to do right initialisation of camera in script.bin or rc.local, but what exactly?? This is part of configuration in my script.fex file: [csi0] vip_used = 1 vip_mode = 0 vip_dev_qty = 1 vip_define_sensor_list = 0 …

Hello! For the Cubieboard 2 on the SD card I use the image Armbian_5.25_Cubieboard2_Debian_jessie_default_3.4.113.img. It is only loaded with U-boot v2015.10.rar. But this U-boot v2015.10 480 MHz DRAM. At this frequency, my Cubieboard 2 freezes. Can anyone build U-boot v2015.10 to 432 MHz DRAM? I will be very grateful. I'm not very good at Linux. I apologize for the bad english.

I am trying to set up a Orange Pi Zero to use as a small NAT/ Bridge Device. I want to use an Android phone in USB tether mode to give its 4g connection to an interface on the opi zero then use a network bridge to join the 4g connection to the lan port, also the opi zero is gonna run a small section of code on the USB interface that changes the TTL of all packets through the interface. On my linux mint box the script looks like pkexec sysctl net.ipv4.ip_default_ttl=65 && echo 65 | pkexec tee /proc/sys/net/ipv4/ip_default_ttl but i am running into issues with the very first part, that is getting my phone native USB tether to be recognized as an interface in …

Hi all, I'm starting with armbian and Banana pi m2p card. I entered image 4.19.21-sunxi, I can not make BT work. with armbian-config I have enabled the BT, next systemctl start bluetooth. with systemctl status bluetooth: Feb 18 18:01:30 bananapim2plus systemd[1]: Starting Bluetooth service... Feb 18 18:01:30 bananapim2plus bluetoothd[1779]: Bluetooth daemon 5.48 Feb 18 18:01:30 bananapim2plus bluetoothd[1779]: Starting SDP server Feb 18 18:01:30 bananapim2plus systemd[1]: Started Bluetooth service. Feb 18 18:01:30 bananapim2plus bluetoothd[1779]: Bluetooth management interface and root@bananapim2plus:~# bluetoothctl Agent registered [bluetooth]…

Hi forum members, when I try to install the kernel headers via: "sudo apt-get install kernel-headers-$(uname -r)" I gote these errors: Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package kernel-headers-4.19.62-sunxi E: Couldn't find any package by glob 'kernel-headers-4.19.62-sunxi' E: Couldn't find any package by regex 'kernel-headers-4.19.62-sunxi' In the /etc/apt/sources.list the lines with the deb-src links are comments. I've tried to uncomment these but got the same errors. So please can somwone point me right kernel-headers Armbian is using ? Many T…

I am considering the purchase of an Orange Pi 3 and I was wondering how well it is supported by the current Armbian image. According to https://linux-sunxi.org/Linux_mainlining_effort it should work mostly fine. How well does Panfrost run on the board? Are there any gotchas that I should be aware of? Thanks.

Hey, I am using the Image from the Armbian Download site: Armbian_20.11.6_Bananapim2zero_bullseye_current_5.10.4 and I am trying to get SPI to work, enabled it using armbian-config and through editing the /boot/armbianEnv.txt verbosity=1 bootlogo=false console=both disp_mode=1920x1080p60 overlay_prefix=sun8i-h3 rootdev=UUID=034edbda-9395-4820-87a1-f3a83bad8a58 rootfstype=ext4 overlays=spi-spidev usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u But after a reboot it does not show in /dev/ (what seems odd, i2c-0 shows in /dev/ even though it is not enabled in the armbianEnv.txt) As far as I understand it, the …

Hi all, I'm new here and somewhat new to "modern Linux"..I'm more a BSD Guy... I'm using, administering and programming on unices since approx 1992, using FreeBSD (mostly) at home, my wife has a Laptop using Mint installed by me, but I haven't put much effort into my Linux experiences since systemd came up... Ok, approx 2 years before I've got a bunch of more or less unusual embedded HW..Beaglebone, Olinuxino with an A10, some Intel based thingy and something from AnalogDevices if I remember correctly. All of them are more or less old. Now I want to build a kind of a home automation appliance that is reading out data f…

I want to use debian wheezy for Olimex A20-micro. Please let me know whether it supports recording from microphone connector and audio out to headphone connector on board.Does there any audio breaking issues with this image or any other debian image. How to install it on Nand Memory of A20-micro board.

My board: Banana Pi, 1Ghz Dual Core, 1GB DDR3, SATA The os base: image http://www.bananapi.com/index.php/forum/others/1372-bpi-m1-bpi-m1-plus-new-image-ubuntu15-04-was-released#3306 Which is apt-get dist-upgraded to wily. I am trying to install self compiled kernel packages from: http://www.armbian.com/github/ I have succesfully used the compile.sh script and output for that is: total 19M -rw-r--r-- 1 petria petria 45K Nov 23 10:03 linux-dtb-next-sunxi_4.6_armhf.deb -rw-r--r-- 1 petria petria 52K Nov 23 10:03 linux-firmware-image-next-sunxi_4.6_armhf.deb -rw-r--r-- 1 petria petria 6.7M Nov 23 10:04 linux-headers-next-sunxi_4.6_armhf.deb -rw-r--r-- 1 …

First of all: my compliments to the staff of armbian for the important work done. I bought some lamobo r1 boards to use in a production environment such as (open)vpn router to realize a tele-service with PLC. I installed bananian (the first distro that I found on internet) but after a week I switched to armbian trying to create my own image from scratch. Very well, I like to have control over things. The question is: I should connect a lipo battery to the board so that when the main power goes off a daemon script syncs sd and then shutdown, but when the main power is reconnected the board must do a reboot automatically. It is possible to do this? Where should my daemon sc…

Hello everyone! I have a Cubietruck Allwiner A20 with 8G sdcard with Armbian 5.04 Debian 8 ( Jessie ) 3.4.110 - sun7i . When you start Cubietruck with sdcard Connected , I run the script /usr/lib/nand-sata-install/./nand-sata-install.sh to copy the image to sdcard NAND . The same performs all the procedures without any error until the moment of PowerOff . When turning off the disconnect sdcard and turn again , though the S.O does not start. It is as if he had not copied anything to NAND , as if empty. Has anyone had this problem ? Grateful for the support of the whol…

Thanks for the hard work on Armbian. I finally got the EmulationStation GUI to run under OpenGL ES @ ~88fps on OrangePI PC. The trick was mostly building SDL2 from source and not installing it with apt-get per the instructions. Really want to avoid anything "mesa". IIRC, I configured SDL2 with a similar command before making: ./configure --host=arm-linux-gnueabihf --disable-video-opengl Then building EmulationStation from source using: cmake -DGLSystem=OpenGL\ ES . make make install FWIW I did symlink some shared objects into /usr/lib/ (like libMali.so) Next is sorting out libretro stuff.

Hello, im new to linux and armbian systems, but im really interested in the topic, recently im working with an a20-Olinuxino-Lime2 , and my goal was to put another OS, for that i followed some tutorials to install a Linux Mate system on the sd card, i configured it to access the internet thought my router but after a point that i changed the kernel , i lost connection to the internet, all my "interfaces" files are the same and i can ping to my router, but i cant ping from my computer to it booting up it gives some errors opening lib modules: systemd-udev(439) could not open builtin file : "/lib/modules/3.4.109-sunxi/modules.builtin.bin" modprob : ERROR: ../lib…

I have an external HDD connected to my OPi One and this are the temperatures in armbian monitor.

Hello I'm using OPI PC+ and tried to figure out some free gpio to play with it. Taking a look at forums/etc there are formula to calculate current GPIO number according to this https://linux-sunxi.org/GPIO and some posts here, there is a formula: (position of letter in alphabet - 1) * 32 + pin number so can someone explain me how pin 38 (PG6) becomes GPIO 198? calculation back from the formula point letter F

Hi, Trying to setup audio mux on orange pi boards, for now trying to stick on orange pi ZERO & ONE ( both of them ). By mux, meaning will try to setup some peers which can play locally or stream sources they have. Let's say all peers have - x2 line in - x1 mic - x1 line out Want to dynamically connect any source to any output on any peer. For example after choosing, you can able to play line in of peer 1 on peer 1 output OR peer1 line in on peer 2 output And I think CD quality is more than enough. Trying to find any tools that will help to make this. Two solution points needed: - hardware: ?? as far as I can find, there is "line…

Hi All, I still can't generate lirc_serial.ko or lirc_gpio.ko [ o.k. ] Looking for user patches in [ userpatches/kernel/sun8i-default ] [ o.k. ] ... [c] 0050-lircgpio_and_raw.patch [ succeeded ] [ o.k. ] Using kernel config provided by user [ userpatches/linux-sun8i-default.config ] I verified, lirc_gpio and lirc_serial are set to "m" in the linux-sun8i-default.config [ o.k. ] Kernel build done [ @host ] [ o.k. ] Target directory [ /root/crosscompile/output/debs/ ] [ o.k. ] File name [ linux-image-sun8i_5.27_armhf.deb ] ar vx /output/debs/linux-image-sun8i_5.27_armhf.deb tar -tvf /root/crosscompile/data.tar.xz | grep '/media/rc' I don'…

Hi, I have just upgraded my BananaPi from Lemaker's Lubuntu 3.4 kernel to the latest Armbian with kernel 4.9 and I can't enable 1-wire to read ds18b20. I suspect the enabling procedure has changed? What I did was: 1. bin2fex /boot/script.bin > script.fex 2. vi script.fex Appended this section exactly as it was on my previous Lemaker kernel 3.4: [w1_para] gpio = 4 3. fex2bin script.fex > /boot/script.bin 4. reboot 5. echo 600000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq 6. modprobe w1_gpio 7. modprobe w1_therm 8. ls /sys/bus/w1/devices/ empty answer In the "known is…

Hi, I performed an apt-get upgrade on my system, and it installed the 4.13 kernel. After the reboot, i started getting the message "bad CRC - using default environment". I spent the whole day reading many threads but still didn't manage to come with a solution. I tried the symlink to /boot/dtb/allwinner from the PC2 forum, but with no luck. I bought this board recently, it is my first board and i am very new to this, although i have decent Linux knowledge. Could you point out what i might have done wrong or if i'm missing something?

1) The included Android image gives a lot of CPU failures when checking with the TTL cable. 2) When adding an Gigabit Ethernet dongle (in this case a Plugable one ~ ASIX Electronics Corp. AX88179 Gigabit Ethernet), the interface name will something similar to enx+Mac address. To replace this a file as the following one must be created: /etc/udev/rules.d/70-persistent-net.rules Containing (remember to replace THE_REAL_MAC_ADDRESS for the displayed enx+Mac interface address: SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="THE_REAL_MAC_ADDRESS", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0" 3) When making an apt-g…

First : i downloaded both Armbian versions for "Orange Pi+ 2" but reported link file names where different from those that actually download : a) link says https://dl.armbian.com/orangepiplus/Ubuntu_xenial_default_desktop.7z, but download file is Armbian_5.38_Orangepiplus_Ubuntu_xenial_default_3.4.113_desktop.7z b) 2nd link says https://dl.armbian.com/orangepiplus/Debian_stretch_next.7z, but download is Armbian_5.38_Orangepiplus_Debian_stretch_next_4.14.14.7z Second : after download i extracted both with : 7z e filename.7z then i run etcher 1.4.4 cli : ./etcher -d /dev/sdd filename.img -y , result sdcard writed, then i inser…

Hello all, just new to here, I bought an Orangepi PC board and grabbed lastest Armbian pre-built image with legacy kernel. I test my code that dynamically change the HDMI output resolution, by something like this: ioctl(disp, DISP_BLANK, true) ioctl(disp, DISP_DEVICE_SWITCH) ioctl(disp, DISP_BLANK, false) and then update fbvar by ioctl(fb0, FBIOPUT_VSCREENINFO) I can see output actually changed, everything goes well until I try to map framebuffer from /dev/fb0, it failed with errno EINVAL. After check drivers source code I think it's because the display driver, it forget to notify the system to update framebuffer parameter…

Hi there, after a recent apt upgrade I have problem with WiFi. I CAN connect to one WiFi, WPA2, static IP. However I CAN'T connect to another one, WPA2, tried with static and dynamic IP. I am using NetworkManager. Searched forum, deleted /etc/networks/interfaces. Information in /etc/NetworkManager/"network name" seems to be correct. Almost the same as for working net. (except uuid & IP info) CAN also connect from laptop. wpa_supplicant line from ps: /sbin/wpa_supplicant -u -s -O /run/wpa_supplicant What should I check else?

Hello everyone! can anyone help with latest debian/ubntu on Opi1+ and emmc storage. There is no /dev/mmcblk1p* . Only /dev/mmcblk0p* (microSD). Aslo there is no option in armbian-config...

I have set up a server on a nanopi-r2s running Armbian version 5.15.25-rockchip64. It all works fine apart from one thing: while other devices can successfully use BIND on the server, the server itself cannot find the local BIND. If I type in this command host device.localdomain 127.0.0.1 it returns the following: device.localdomain has address 192.168.0.20 192.168.0.20 is the correct address for device.localdomain from the local BIND. If I omit the 127.0.0.1 from the command, it does not find the correct address.: device.localdomain has address 36.86.63.182 device.localdomain has address 36.86.63.182 Host device.localdomain not …

I am using orange pi pc plus after using armbian system, there is an infinite network with WLAN0 and WLAN1, but at present there is no law to use both networks at the same time and connect different SSIDs. Error: Connection activation failed: (7) Secrets were required, but not provided. pi@orangepipcplus:~$ cat /etc/os-release PRETTY_NAME="Armbian 24.5.0-trunk.512 jammy" NAME="Ubuntu" VERSION_ID="22.04" VERSION="22.04.4 LTS (Jammy Jellyfish)" VERSION_CODENAME=jammy ID=ubuntu ID_LIKE=debian HOME_URL="https://www.armbian.com" SUPPORT_URL="https://forum.armbian.com" BUG_REPORT_URL="https://www.armbian.com/bugs" PRIVACY_POLICY_URL="https://www.armbian.co…

Hello i am working at project with olinuxino micro and USB 3G modem. From my experience i sometimes i need hard reset modem (turn off,turn on from USB connectro) i see that power is controlled by USB1-DRV (PH6) and USB2-DRV (PH3) I try to manually set this pins (PH6 and PH3) to LOW and after some time HIGH level to turn off and on power on USB connectors but this pins i see isn't configured as normal GPIO pins. so i have error in pyA20 - that this pins aren't GPIO. I ma a hardware guy so i have only a little experience in programming Can anybody help me with this ? Best Regards Robert // edit for others : i just find on cubieboard foru…

I have done a fresh installation of the Debian image (http://mirror.igorpecovnik.com/Armbian_4.5_Cubietruck_Debian_jessie_4.2.3.zip), but since that the linux does not report any information on power and the battery. There is no information in /sys/class/power_supply. As I am not an linux expert, any useful informationhighly welcome

Hi, I wanna try the armbian for banana pi M2 but when i flash the image in the microSd card with Rufus (i'm on windows 10) the pi does not boot correctly, i.e restarting every 10 seconds. Afterwards the card is not easy to reformat, not accessible on windows. In Rufus I do (i tried with 2 different cards): - choose the .raw file - then the combobox is set to DD image - finally i click on start So is there something I totally miss? Thx

So, the Linux Kernel 4.6 is out. Supposedly it comes with a lot of new ARM processor support. I'm excited about this. I'm not too knowledgeable when it comes to kernel development, especially with ARM devices. I guess the question is, what's it going to take to move the devices that use these supposedly newly supported chips up to 4.6? I'm somewhat keen on updating to a kernel that isn't approaching EOL.

Hello, I leave in a place where we occasionally get really heavy storms or the power gets cut for some reason. This most often does not happen more than five minutes, but there has been longer cases. Now, this poses an obvious problem with my headless server (Orange Pi PC btw). I went on a week trip last month, to discover the development board I needed was completely down. I called a friend and the power had indeed been cut off in my neighbourhood, but my server would no longer respond over SSH. I hard reset the server by power cable and tried restarting sshd (after getting home a week later), just to get warning that the action of the service was queued and afterwards w…

where can i find de virtual Linux usb server for my orange pi pc and armbian 5.2? i download jessie desktop regards Tex

I remember there where a problem before, shutdown leads to reboot. But now it's the opposite - reboot leads to shutdown. Both gui button or: sudo reboot reboot sudo shutdown -r now sudo init 6 from terminal, or ssh, behave the same. This is on Armbian_5.25_Orangepipc_Ubuntu_xenial_default_3.4.113_desktop / Armbian_5.25_Orangepione_Ubuntu_xenial_default_3.4.113, from download section and self built.

Hallo, In my mind i want to build a cluster with 5 bpi m2+. Purpose: Home-server- Storage off all media files/also using cointainers/Raid*** - Back-up for Win/Linux based pc in home. Media-server(KODI)- Use at first one screen/future >more -access by internet Back-up -Cloudservice (for example BOX) Extra - NAS ***(5 bpi * 2 usb can be up to 10 usb-harddisk off 2GB or more. I just started with bpi. But this what i have in mind. So 20 GB or more can be set to Raid0/Raid5 Every information is welcome. Also about wich Os can work the best etc.. With kindly regards, Henk

Hey folks, I'm hoping for some advice on achieving decent graphics for my application. I've got a prototype running with a custom board hosting the NanoPi Neo Air and a bunch of my own hardware. The biggest issue right now is getting reasonable graphics performance. The difference between mainline and legacy support has had me confused and switching back and forth trying to find a useful solution. Here's what I've learned so far: Mainline feels like the future, so that's my preference. My application uses fbtft over SPI for the graphics. I achieved 72MHz SPI on mainline which gives almost reasonable performance. On legacy the SPI driver seems buggy and …

Hello and hi everyone. So I've got a Cubietruck with the NAND replaced by TSD eMMC. The TSD behaves like an SD card, and previously tested to run OK using Cubieez-TSD. However, I need to run Node.JS on the Truck, and the Cubieez Debian Wheezy Node.JS support stops at v6 (now we're at NodeJS v8). Ubuntu Xenial will still have NodeJS v8 support, so it's good excuse to change to a new OS. I'm using this image to successfully flash my SD card: Armbian_5.31_Cubietruck_Ubuntu_xenial_default_3.4.113_desktop. First time booting the CT from SD, I got the usual prompt, then the desktop loaded. First problem: The screen is misaligned. https:…

Hi, I have a problem with the wifi connection of the Orange Pi Lite when I connect a HDMI device and switch it on. It is not possible to get the wifi working. I have the same auth. error message like many others here too. But the wifi works well without HDMI device or when the device is off. I have tested the last debian and ubuntu server version and mainline. Thanks for helping

Hi, Good people of Armbian-land! First of all, thank you all for the awesome work you've been putting into Armbian. I recently purchased an Orange Pi PC, for which I'd like to use the Ubuntu desktop image, since I need the HW acceleration features. I tried using Mainline briefly but after confirming that the performance is just not there without the Mali drivers (as suggested by the description, so no surprise there), it seems Legacy is my only viable option. Which would be fine, but the monitor I'd like to use with my setup doesn't work with legacy (it works fine in Mainline). Also a sidenote: I connected the monitor using an HDMI-VGA converter. I set th…