Allwinner sunxi

Hi, I bought a 3.5 inch RPi LCD display from here: https://www.aliexpress.com/item/32965280840.html?spm=a2g0s.9042311.0.0.2a474c4dxALiQy I connected the display straight to my Orange Pi zero board. The slot on the Orange Pi Zero is flipped compared to RPi so the LCD display goes outside the board. I guess that is the right way to connect. Anyway, when I power on the board I can see illuminated screen. The problem is that everything I have tried to configure the LCD was unsuccessful. I am trying with the Armbian image mentioned in this web site: http://www.orangepi.org/orangepibbsen/forum.php?mod=viewthread&tid=3773 (Armbian_5.35_Orangepizero_Ubuntu_x…

Hello! I'm using Wheezy under kernel 3.4.x on Lime2 with 7" LCD and i added fbcon=rotate:1 in boot.cmd and the console booted in portrait but LXDE is still in landscape. I also added FBDEV_ROTATE_CCW=90 but with no results. I can rotate the screen from the /usr/share/X11/xorg.conf.d/XX-fbturbo.conf file but every time i touch the screen the LXDE crashes. Any suggestions please how to rotate the screen in LXDE? Thank you!

I've read the opi win have a receptor radio fm in the chipset, how use that ? tks

I met a problem that kernel showed allwiner H6 ethernet internal error. link: It is hard to loacate what makes that error occur, I wish that kernel can show my log added to drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c. my work below: 1 Added printk to drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c, and made patch with git format-patch, move patch to userpatchs/kernel/sunxi-next. 2 run ./compile.sh to compile armbian, I am sure that patch work, have checked drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c after compile.sh completion 3 burn Armbian_5.71_Orangepioneplus_Ubuntu_bionic_next_4.19.13_desktop.img to sdca…

Hi: when iI'm using gpio of orangepi zero+, I found gpio is not usable, I can't find any way to let it work,please help me ! the device of gpio is: gpiochip0 -> ../../devices/platform/soc/1c20800.pinctrl/gpio/gpiochip0/ lrwxrwxrwx 1 root root 0 Jan 1 1970 gpiochip352 -> ../../devices/platform/soc/1f02c00.pinctrl/gpio/gpiochip352/ but the Orangepi Zero's gpio is : gpiochip0 -> ../../devices/platform/soc/sunxi-gpio.pinctrl/gpio/gpiochip0/ is it the reason? how to let the gpio device work? please help me!

I've tried to the best of my abilities, but it seems that the current Bionic image does not support the K1 Plus wifi? Is that correct? In armbian-config there is no option to setup wireless and I cannot get the board to recognise a wlan0 device by changing the interfaces configurtation.. Is there some trick?

I have OrangePi Zero 512 with Armbian Bionic. I hav econnected LED diode to GPIO PA12 pin. When I (re)boot the device, LED is automatically on. I have to switch it off then manually (with Python script). Is there any config file in Armbian to define which GPIO ports should be switched off?

Ok. I'm trying to use my orange pi pc for send ir signals to my tv. I'm using lirc on an armbian stretch 9.9. the ir receiver works fine, but when I try to emit with the command: irsend SEND_ONCE tv KEY_5 (tv is the name of my lircd.conf), those ir signals that I previously recorded and saved on my lircd.conf file it shows the following error: Hardware does not support sending error running command: Input/output error Thanks in advance.

My friend, when he next inserted the microSD card into the Orange Pi Zero 2 slot, the microSD slot fell off the board 😞 It is not possible to solder it because some of the tracks on the board have become detached so Is it possible to run the ArmBian system on OZPi v2 with a copy of the microSD system on a USB Pendrive? I am looking for a method to run OZIPI v2 without microSD on the system via USB disk

Hi, as the title says while building this image i had this console reported error: E: Unable to locate package mali-sunxi-utils Also i would like to ask if there is hw acceleration(gpu) on xenial desktop images Thanks

Hello. I try to put on Zero Armbian Jessie, after rebooting it does not connect via SSH. Tell me where I make a mistake. Thank.

Good day, for my Orangepi PC+ I installed Armbian Ubuntu Jammy on a µSD card. Up until Armbian Ubuntu Strech I was able to use a PCM510A for sound output. The settings for this were easy. With all updated OS after Strech, I can't install the PCM. Unfortunately, the help that was published in the forum wasn't helpful or I couldn't take it over. On the eMMC I have installed Armbian5.59 Orangepipcplus Ubuntu xenial default 3.4.113 desktop. Because of the advanced age of this OS, there are no updates and upgrades. Luckily my internet radio still works. Can someone explain to me how I can install the PCM510A at Jammy? Kind regards hajupiko49

I'm running some stress test on the NanoPi neo2 512mb, CPU heating reached 75-76 degrees, and it's stable, the problem that I faced is that the computer changed it's IP suddenly (after 55 minutes of test running), I guess it's because of a network card reset. Did anyone face the following issue? Is it related to the stress test? Or it's another networking problem? The test I'm running is with the "stress" tool, running long time stress on 4 CPUs. In addition, does anyone have any insights regarding this device? good or bad?

Hi, Nano pi duo 2 module I2C is not working in kernal Armbian Focal 5.10.21. I have camera OV5640 attached to Nano PI duo 2 via I2C 2 I found my I2C2 is disable how can I enable? root@nanopiduo2:~# fdtget /boot/dtb/sun8i-h3-nanopi-duo2.dtb /soc/i2c@1c2b400 status disabled I found I2C 2 which is connect to camera is not working root@nanopiduo2:~# ls -l /sys/class/i2c-adapter/ total 0 the I2C detect command and sometimes armbianmonitor does not genetrate the link, root@nanopiduo2:~# i2cdetect -y 0 Error: Could not open file `/dev/i2c-0' or `/dev/i2c/0': No such file or directory root@nanopiduo2:~# i2cdetect -y 1 Error: Could n…

Hi, I'm migrating from the OrangePi image to Armbian, and can't make the touchscreen working, it does not respond to any actions. It works pretty well on the OrangePi's image. Did I mess up something here? uname -a: Linux orangepizero2w 6.6.31-current-sunxi64 #1 SMP Fri May 17 10:02:40 UTC 2024 aarch64 GNU/Linux Touchscreen DTS: /dts-v1/; /plugin/; / { compatible = "allwinner,sun50i-h616"; fragment@0 { target-path = "/"; __overlay__ { backlight_gpio: backlight_gpio { compatible = "gpio-backlight"; gpios = <&pio 8 14 0>; // PI14 …

I configured my opi to work as a composite usb gadget (mouse and rndis). Everything works, but the actual refresh rate of the mouse was 250 Hz. I tried to configure bInterval, which is responsible for the device update frequency, this could only be done by rebuilding the kernel with bInterval changes in the high-speed descriptor structures from 4 to 1 in the file drivers/usb/gadget/function/f_hid.c. It had an effect. But the frequency only rose to 500 Hz. I tried to find what could limit this, I looked in drivers/usb/dwc2/gadget.c and also in composite.c but I couldn’t find anything. Now I don’t know where to look next or i missed sth.. drivers/usb/gadget/func…

I'm trying to use an OrangePi Zero as an Alexa device, using github.com/alexa-pi/AlexaPi. This is headless, but I need analogue out and in. Given that it's headless, I thought I'd use the mainline kernel instead of headless. Everything installs fine, but ALSA does not see anysound card hardware. aplay: device_list:268: no soundcards found... I can try legacy, but I'd prefer to use mainline if possible.

Hello, I want to read data from UART3 on OrangePi One. I want to use UART3 (pin 8 & 10), so I enabled uart3 overlay at /boot/armbianEnv.txt. Now I expect to read data via minicom -b 115200 -D /dev/ttyS3 but I read nothing unfortunately. What am I missing? Any help is appreciated. I'm using Linux orangepione 4.19.38-sunxi (sorry, armbianmonitor doesn't generate link) Thank you, Regards

I was searching for a UPS for the Banana classic and then saw you just can connect a battery to it. What i can't find information about if it needs to be unprotected or if i can use my protected Keeppower 18650 Li-Ionen's that i already have for my flashlight anyway. And is there anything special i need to do in Armbian? Just connect the battery and it works? Hard to find information :-(

Hi, I want to use my cubietruck to play the video in HD and with spdif pass-trougth and I want use mopidy. with last armbian jessie desktop : with mplayer2 : pass-trougth is ok but video is too slow with mpv : I heard a very loud noise at the output of the amplifier is not DTS decoding and is transmitted as the pcm.--> it is a kernel problem: the driver sends a sound that is not recognized by the amplifier. the SPDIF sound format is limited to 24 bits video is OK. mopidy is OK with last armbian xenial: it work because mpv is very old with mplayer2 : pass-through and video is ok but kernel panic when I put the video paused--> kernel bug solved : …

I have a BananaPi M1+ running pure-ftpd, it was fine when using Armbian 5.14, but I have a problem after upgraded to Armbian 5.20. Here is the output of the filezilla client : If I disable the firewall by clearing all the iptables rules, filezilla can connect to pure-ftpd without problem.

Hello! Board: Orange Pi 3 LTS SATA-USB3: Bus 002 Device 003: ID 152d:0578 JMicron Technology Corp. / JMicron USA Technology Corp. JMS578 SATA 6Gb/s Speed after load: sudo dd if=/dev/sda of=/dev/null status=progress ... (5,8 GB, 5,4 GiB), 50 s, 115 MB/s Speed after spindown: sudo dd if=/dev/sda of=/dev/null status=progress ... (4,5 GB, 4,2 GiB), 71 s, 62,9 MB/s After reboot the speed is again 115 MB/s The drive does not respond to changes in Power Management settings. Help me solve the problem. Sometimes the disk cannot start after spindown. Thanks!

trying to get ili9340 to work on orangepi pc2 on bionic 4.14.91 ... there's a fb_ili9340 module in the staging directory, modprobe passes and the only thing in dmesg is warning it's staging nothing else but when I check /dev/fb* there's only /dev/fb0 (the original hdmi output on my monitor), there's no /dev/fb1 anyone can land a hand? give a hint?

Hello, long time Banana Pi user here. I have a BPI-M2+ and recently decided to write Armbian_23.02.2_Bananapim2plus_bullseye_current_5.15.93_minimal.img to emmc. I am using cat6 over gigabit LAN and am seeing scp and rsync transfers to the device averaging 1.7mb/s. Transfering an 850mb file took unusually several minutes. It starts off at 40mb/s then quickly drops to under 2mb/s. Is this typical? I would think over LAN I would be seeing much faster speeds. Untarring this same 850mb archive also took unusually long. Could the emmc be damaged or on it's way out? How would I check? Please see armbianmonitor output. https://pastebin.com/RCa…

Hello i am running armbian wheezy with the legacy kernel on an olimex a20 lime. I have atached an audio jack to the gpio pins. But cant get any sound on the output using speaker test. Do i need to do some configuration to get this to work ?

Hello I have desktop version and I can`t on the AV sound card. The sound works on HDMI. Could You advice how to do it? I`m try to this solution but sound card is still not available. alsamixer is diffren

I got that stability issues on my banana pi m1, and notice that the last kernel available on armbian still the 4.14.18. Today I also run apt upgrade on raspberry pi 3 and it installed the kernel 4.14.30 that stop the ipsec vpn working, the same as in 4.14.18 used on armbian. I feel some frustration on the latest kernel updates, and wondering if anyone have some info about the next kernel update that solve this issues. Do you advise me to change to nightly builds to get a new kernel to test? สมัครufabet Any suggestion would be greatly appreciated.

Hello folks! I'm investigating an odd issue of the OPi R1 board, with the image Armbian_5.83_Orangepi-r1_Debian_stretch_next_4.19.38. With this version of software the board works fine, but apparently the wifi cannot reconnect after a disconnection (error: association request to the driver failed) The only workaround I found is to manually bring down the wifi interface and then back up; then the reconnect is almost immediate. I tried to disable the NetworkManager and now I'm using /etc/network/interfaces file to handle the connections but the problem still persists. I checked the issue with another R1 board and so I can exclude that the boa…

Hi all Need's help, my devoces orange pi plus 2 and distibtion os armbian server, me need hardware acceleration on plexmediaserver, i used more ways, did not help.

Hi, First time user here. I'm using the legacy Jessie build with kernel 3.4.109 Kernel. OTG is enabled and generally working. However, with some USB devices we are getting the following message with dmesg: WRN:L2705(drivers/usb/sunxi_usb/hcd/core/sw_hcd_host.c):ERR: sw_hcd_schedule, best_end [ 663.633167] WRN:L2951(drivers/usb/sunxi_usb/hcd/core/sw_hcd_host.c):ERR: sw_hcd_schedule failed [ 663.641968] cannot submit datapipe for urb 0, error -28: not enough bandwidth This only happens with some USB devices. My USB headphones work fine but a USB DAC for music does not. I remember reading somewhere the OTG on the BananaPi seemed limited in terms of actual conne…

I just installed the image located here and am unable to get a bluetooth keyboard and mouse to connect. https://www.armbian.com/orange-pi-zero-plus-2-h3/ And used armbian-config -> Network -> Enable bluetooth. Here's the output of some common debugging commands I found in the forums. root@orangepizeroplus2-h3:~# lsusb Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 001: ID 1d6b:0001 Linux Foundation…

I apologize for asking such a basic question. I have recompiled the wifi module on an Orange Pi PC+ to operate in concurrent mode so it can act in both station and AP mode at the same time, allowing it to be a wifi repeater. The problem is, this feature is lost on every kernel upgrade, requiring me to recompile the module each time I upgrade the kernel. The kernel module driver often changes slightly between kernel versions, and I have to track down and fix new bugs in the source code that prevent it from compiling when concurrent mode is enabled. I'm happy with how the wifi module performs now, but don't want to lose the ability to get needed kernel updat…

SBC is banana pi M1 I tried the banana pi at church today, things went great as for the Libreoffice impress presentations but it was hard to navigate to menus because the banana's resolution was set to 1920X1080p. Everything was too small in the projector, we need something like 1280X1024 or 800X600. I tried `a10disp changehdmimodeforce 4` to change it to 720P, on the projector but display became unstable and I had to reboot to get it back. We have two modes for projector, VGA (HDMI->VGA converter cable) or plain HDMI. Today I tried the VGA but we can also do HDMI. Please help. Thanks.

I'm sorry for the lame question, I just don't wanna regret anything before buying this fan, so I'm talking about this fan (3cm x 3cm) Spoiler I want to mount this fan right below the board by just screwing it in. Do the holes fit perfectly with the holes of the opiz board ? I've asked this before on facebook but someone suggested me to just glue the fan directly onto the board but I'm afraid it'll damage the board instead.

I'm looking to build an ntp server using the OrangePi Zero 3 and I noticed there is no pps-gpio device tree overlay for the h616 chipset only the h5 chipset. Has anyone created a custom dt overlay? Thanks in advance.

I've tried to downgrade the kernel with the armbian-config tool, but now the opi+2 hangs while booting from emmc. I can boot via sd card, but i dont know how to fix the problem - please help.

Hallo, In my mind i want to build a cluster with 5 bpi m2+. Purpose: Home-server- Storage off all media files/also using cointainers/Raid*** - Back-up for Win/Linux based pc in home. Media-server(KODI)- Use at first one screen/future >more -access by internet Back-up -Cloudservice (for example BOX) Extra - NAS ***(5 bpi * 2 usb can be up to 10 usb-harddisk off 2GB or more. I just started with bpi. But this what i have in mind. So 20 GB or more can be set to Raid0/Raid5 Every information is welcome. Also about wich Os can work the best etc.. With kindly regards, Henk

Hello, dear members! I built the mainline kernel 6.0.8 using the config-5.15.80-sunxi64 config, but when I try to boot the system hangs on Starting the kernel. Boot log: U-Boot 2023.01-rc3-00069-g93685d0dcb-dirty (Dec 19 2022 - 11:31:13 +0300) Allwinner Technology CPU: Allwinner H6 (SUN50I) Model: OrangePi 3 LTS DRAM: 2 GiB Core: 50 devices, 14 uclasses, devicetree: separate WDT: Not starting watchdog@7020400 MMC: mmc@4020000: 0, mmc@4022000: 1 Loading Environment from FAT... Unable to use mmc 0:1... In: serial@5000000 Out: serial@5000000 Err: serial@5000000 Net: No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0,…

Hi I have nano pi m1 with armbian installed. When I play video on firefox, it shows but the sound is too choppy like sea waves and I don't hear the real sound. what should I do to fix it?

Hello everyone, I want to do something simple with my OrangePi One Plus. That is to connect a bluetooth speaker and play wireless from the Pi with a CSR8510 A10 USB dongel. The dongel works and i can pair with every device. Even with my JBL Go 2 bluetooth speaker: hj@PLUS-OrangePiOne:~ $ sudo bluetoothctl [NEW] Controller YY:YY:YY:YY PLUS-OrangePiOne [default] Agent registered [bluetooth]# power on Changing power on succeeded [bluetooth]# scan on Discovery started [CHG] Controller YY:YY:YY:YY Discovering: yes [NEW] Device XX:XX:XX:XX JBL GO 2 [bluetooth]# scan off Discovery stopped [CHG] Controller YY:YY:YY:YY Discovering: no [CHG] Device XX:XX…

Hi Igor and everyone else who is supporting this forum with their time and effort. Thanks in advance for reading this and giving it a thought! Question: Any idea where I could turn off mounting /dev/sda1 read only? Problem description: Before moving cubietruck to a new location I did an dist-upgrade, after that a reboot didn't work. First I was asked for debug and root password. After editing I did try to solve my problems without using your help. But I did not succeed yet. Neither with installing a new image and restoring my lamp-stack from backup nor with solutions I found in this forum (changing u-boot config and so on). I did backup sd-…

First of all, thank you very much for the great work! On cubietruck after upgrade to 5.20, I have some trouble with network bonding. /etc/network/interfaces: auto eth0 iface eth0 inet manual bond-master bond0 bond-primary eth0 bond-mode active-backup auto wlan0 iface wlan0 inet manual wpa-ssid xxxx.xxx wpa-psk xxxxxxxxx bond-master bond0 bond-primary eth0 bond-mode active-backup # Define master auto bond0 iface bond0 inet static address xxx.xxx.xxx.xxx netmask xxx.xxx.xxx.xxx gateway xxx.xxx.xxx.xxx hwaddress ether xx:xx:xx:xx:xx bond-slaves none bond-primary eth0 bond-mode active-backup bond-…

I'm looking to compile a kernel for Gentoo (Orange Pi Prime), but afaik the HDMI support has not been mainlined yet. Does anybody know how Armbian kernels have it? And is there more to it than just the kernel sources? Last time I tried, I had no luck getting output.

Hi All, Can you please help me how can I set up OV5647 camera with Orange Pi One? Where can I find driver for it? Camera link: https://www.aliexpress.com/item/Orange-Pi-fish-eye-Camera-Night-Vision-for-Orange-Pi-PC-Zero-One-PC-Plus-Plus2/32864676943.html?spm=2114.search0604.3.26.74868de282hQoP&ws_ab_test=searchweb0_0,searchweb201602_5_10065_10068_5015215_10059_10696_100031_10084_5015115_10083_10103_451_10618_452_5015815_10304_10307_10820_10821_5015915_10302,searchweb201603_16,ppcSwitch_5&algo_expid=44e91c9c-67e1-49b9-83f3-2c2890deab01-3&algo_pvid=44e91c9c-67e1-49b9-83f3-2c2890deab01&priceBeautifyAB=0 Thanks!

I'm trying to enable GPU support for watching youtube on orange pi 2 zero w model. But there is no Mali driver and even kernel package How can I enable this?

Hello, i have a old Banana Pi M2 with the current Armbian in use. I use the green LED with Heartbeat Signal. Today i try to connect with putty but after Username and PW nothing happen. Samba Service work normal. Then i have look at the Banana and the green LED was lightning constant and no heartbeat blinking. Maybe the trouble was because in a few meters distance sawed with a circular saw. Has perhaps caused interference or power fluctuations. No idea and maybe just coincidence. I have been using Armbian for only two days. Previously, the manufacturers ran Distribution for two years. I have Google and found out t…

Hi everyone, has anyone tried to make the above mentioned tuner work with Cubietruck? If so, were you successful? Again, if so, what are the necessary steps? It should be possible with kernel 4.11, since the latest LibreELEC distribution includes the drivers in kernel 4.9. Help would be appreciated! Thanks and cheers, chessplayer

Hi, 2 weeks ago I upgraded my Cubietruck to newest Armbian version: root@cubietruck04:/var/log# uname -a Linux cubietruck04 5.10.4-sunxi #20.11.6 SMP Sun Jan 3 21:28:45 CET 2021 armv7l GNU/Linux root@cubietruck04:/var/log# lsb_release -a No LSB modules are available. Distributor ID: Debian Description: Debian GNU/Linux 10 (buster) Release: 10 Codename: buster Since that upgrade the Cubie is crashing often compared to the last years ( every ~3 days), in the last 3 years I have never observed that. Please help me to find out the issue. From kern.log I see 2 different crash reasons: Jan 2…

with hdmi figured out. Rather, he himself earned a normal. It could be seen that a reboot was needed. Therefore, I rename the topic Has anyone tried to use the Majordomo for Armbian? Have experience? I want to try using orange pi for a smart house

Neo has one SPI port and I need two, so would like to add another spi using spi-gpio, but no success (I think). I am using Armbian 23.02.2 Bullseye, default kernel does not enable it, recompiled using linux-source-5.15.93-sunxi.tar.xz, enabled spi-gpio as module. Digged around forum, prepared below dts and armbian-add-overlay succeeded. But there is no message arrived when loading (dmesg shows nothing about spi) and no /dev/spi* created. Is it OK or there must be something? Please advise.... / { compatible = "allwinner,sun8i-h3"; fragment@0 { target-path = "/"; __overlay__ { …

Hi, I am running a OrangePi One with Linux orangepione 3.4.113-sun8i #18 SMP PREEMPT Wed Jan 24 22:10:49 CET 2018 armv7l armv7l armv7l GNU/Linux DISTRIB_ID=Ubuntu DISTRIB_RELEASE=16.04 DISTRIB_CODENAME=xenial DISTRIB_DESCRIPTION="Ubuntu 16.04.3 LTS" And it seems that when I start the system without the hdmi cable and plug it afterwards, the HDMI is not handle correctly and my TV stays with a red screen. There is some way to configure the hdmi hot plug in this OS? I found that raspiberry pi has this option. (https://www.raspberrypi.org/documentation/configuration/config-txt/video.md)

So I'm pretty new at using serial ports in linux so not even sure if this is the right place. I'm playing around with MIDI using the serial ports on the Orange PiLite - it uses the baud rate of 31250 to achieve this you use setserial to get the base_baud (which it reports as 1500000) and you divide by the speed you want to get the divisor i.e. 1500000/31250 = 48 this becomes >setserial /dev/ttyS1 divisor 48 speed_cust So now when you use 38400 as your baud speed it actually becomes 31250.... ...in theory after some fiddling I found the divsor is actually 50 as 48 gives you weird results which would suggest that the base_baud is actually 1562…

Hello everyone! can anyone help with latest debian/ubntu on Opi1+ and emmc storage. There is no /dev/mmcblk1p* . Only /dev/mmcblk0p* (microSD). Aslo there is no option in armbian-config...

where did tunl0 come from ? is it there by default or .... may be I must dig in my history ? root@orangepione:/etc/network $ ifconfig -a eth0 Link encap:Ethernet HWaddr 6a:xx:xx:xx:xx:xx (** edited) inet addr:192.168.100.3 Bcast:192.168.100.255 Mask:255.255.255.0 inet6 addr: fe80::68f2:91ff:fef0:4579/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:35677 errors:0 dropped:0 overruns:0 frame:0 TX packets:22173 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3139622 (2.9 MiB) TX bytes:13744564 (13.1 MiB) Interrupt:114 lo …

I got a new board revision of the Olimex A20-OLInuXino-MICRO Board (Rev. J). It works with the by Olimex provided Jessie image but not with Armbian_5.25_Micro_Debian_jessie_next_4.9.7. I get no IP address by DHCP because the ethernet is not working. The reason could be an new ethernet chipset they introduced with this revision. New: Microchip's LAN8710AI-EZK(QFN-32). Before: Realtek RTL8201CP(LQFP-48) They publish a patch on: https://github.com/OLIMEX/OLINUXINO/blob/master/SOFTWARE/A20/A20-build-3.4.103-release-5/a20-phy_1000_100-dram.patch

Hi, I was wondering if anyone had been able to get this working ? And, yes i know that OPI-Win is WIP/testing. I read some stuff here & on the linux-sunxi irc log that seemed to say that it should work & I've tried the following without luck. I was wondering if someone with alittle more knowledge about this may be able to help or point me in the right direction. I also tried to compile u-boot v2017-09 but it fails with a sdram too big error I tried to backport some of the config to 2017-07 but that'll take time i expect ... /boot/armbianEnv.txt (many combinations of this) disp_mode=720p60 disp_dvi_compat…

Hey there. I ve been using armbian since a couple of years now. Today, out of the blue, I receive a 'user is not in the sudoers file '. I currently I'm using ARMBIAN Ubuntu 14.04.5 LTS 4.8.4-sunxi. Obivuously, my user WAS a sudoer, actually, it is the only user. Any ideas would be very much appreciated. Thanks!

Hello, I have an orange pi plus 2 device. but Armbian 5.69 (5.75 or latest version) above Orangepiplus Ubuntu xenial default can be the url for desktop version. Can you please give me the working url? (By the way, I couldn't find a section for orange pi plus 2 in the forum. )

Hello everyone! I am trying to set up a CSI camera for my Orange Pi win plus (A64). The camera is GC2035 and I have already seen it not easy with latest versions. New versions of Armbian have not CSI support and do not have drivers gc2035 and vfe_v4l2. I found you can somehow compile the driver but honestly.....I do not understand how. I know the process of ./compile.sh but no idea how to use this https://github.com/avafinger/gc2035 It says is for H3, probably not for A64 right? Looking for the oldest version of Armbian I could use, I found out on the archive this one: Armbian_5.59_Orangepiwin_Ubuntu_xenial_default_..&g…

Is it possible to soft reset USB device/hub on legacy kernel? On x86 I used to use some C code (opening usb and sending ioctl USBDEVFS_RESET) but id does not work here on arm...

Lost the login motd following apt-get upgrade. Start-Date: 2016-05-08 10:52:11 Commandline: apt-get upgrade Upgrade: linux-image-next-sunxi:armhf (5.04, 5.10), linux-headers-next-sunxi:armhf (5.04, 5.10), linux-trusty-root-next-cubietruck:armhf (5.04, 5.10), linux-dtb-next-sunxi:armhf (5.04, 5.10), linux-firmware-image-next-sunxi:armhf (5.04, 5.10) End-Date: 2016-05-08 10:56:33 I imagine I have to reinstall a pam config file?

Hi, this is not a complaint, just wondering if I am doing something wrong. When I try "any(Pine64,Sopine,Olinuxino-A64,Bananapi-M64)" A64 board with armbian 3.10.x kernel, desktop performance is quite satisfactory. Example: https://dl.armbian.com/_old/pine64/archive/Armbian_5.90_Pine64_Ubuntu_xenial_default_3.10.107_desktop.7z But when I build armbian in docker, both 5.4 and 5.6 kernels, I experience dramatic slowdown on desktop performance, even cursor is moving slowly. Here are armbian monitor logs: http://ix.io/2oW4 and http://ix.io/2oVY Here is how it looks on BPI-m64 as an exam…

Hi there, I installed the Desktop version of Jessie, it was working good, but after I wanted to check the Server version too "Armbian_5.14_Orangepione_Debian_jessie_3.4.112.7z", but it just wont boot up, no Led's glows up on the board. Tried more times to install on different MicroSD cards, but I got the same non boot results. Just to mention that the Desktop version is working on all MicroSD cards I tried! Thank you for your answer! Kind regard

Hi, I'm trying to put my OPI zero in mono instead of stereo by default. On ARMbian my alsa config file (/etc/asound.conf) looks like this : pcm.!default { type plug slave.pcm "dmixer" } pcm.!dmixer { type dmix ipc_key 1024 ipc_perm 0666 slave { pcm "hw:0,0" period_time 0 period_size 1024 buffer_size 4096 rate 44100 format S32_LE channels 2 } bindings { 0 0 1 1 } } ctl.!dmixer { type hw card 0 } I tried to add something like this but without success : pcm.makemono { type route slave.pcm dmixer …

Hello, I try to setup my Orange Pi Lite with a thermal printer (http://www.ebay.de/itm/122418910118?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT). With my Arduino the printer works perfect, so it is actually ok. I just can't figure out how to use the ttl connection. I installed pyA20 and try to implement a kind of SoftwareSerial and it didn't worked really well: #!/usr/bin/env python """Basic blinking led example. The led on A20-OLinuXino-MICRO blinks with rate of 1Hz like "heartbeat". """ import os import sys import time if not os.getegid() == 0: sys.exit('Script must be run as root') from time import sleep from pyA20.gp…

Hello, I would like to ask your help with the following problem. I'm able to put my Orange Pi PC Plus to suspend state using this command: echo -n mem>/sys/power/state When I wake it up using the SW4 pushbutton it resumes operation properly. I would like to automatically execute my script every time the system resumes from suspend state. I found two different methods, I've spent several hours trying them and non of them seems to be working with Orange Pi PC Plus. First method: using /lib/systemd/system-sleep Second method: using /etc/pm/sleep.d It seems my system does not execute the scripts confi…

Hi, i use Debian Stretch 9.3 on a Cubitruck, it run‘s with a 3.14-Sunix Kernel, i wan‘t to Upgrade to a newer Kernel like 4.X, how ca i do that? Thank you? Gesendet von iPhone mit Tapatalk

Hi All, I've installed Armbian Legacy Jessie onto Cubieboard 1 A10. currently it's running from SD. Connected with USB OTG cable to my Win PC. It's powered via the OTG port. I'm trying to enable USB mass storage with no success. modprobe g_mass_storage file=/dev/mmcblk0p1 removable=y Here's the log: [ 1155.371894] g_mass_storage gadget: Mass Storage Function, version: 2009/09/11 [ 1155.376004] g_mass_storage gadget: Number of LUNs=1 [ 1155.380105] lun0: LUN: removable file: /dev/mmcblk0p1 [ 1155.387175] ep_matches, wrn: endpoint already claimed, ep(0xc0a2fb14, 0xbf16d71c, ep1-bulk) [ 1155.393386] g_mass_storage gadget: Mass Storage Gadget, version: 2009/09…

Hello I have a bananapi m1 with armbian Linux bananapi 4.3.3-sunxi #3 SMP Mon Dec 28 11:27:16 CET 2015 armv7l GNU/Linux I need to add serial ports so I think I need to rebuild a kernel as described here: http://forum.armbian.com/index.php/topic/371-cubietruck-uart-3-4-7-pin-out-serial-ttys/ I follow the step described here: http://www.armbian.com/using-armbian-tools/ But when I run the compile.sh script, I don't found banapim1 in the list of device, I see banapim2, bananapipro, banapim2plus but not my deice. Could you indicate which ne must be selected? Thank you

Hello, I attached Micron M500 SSD with gpt table, also Seagate 3GB hard disk with gpt to sata data connection and powered disks with external power adapter(it supplies 5V and 12V and comes with usb-sata adapter). U-Boot shows message: SCSI: AHCI PHY power up failed. dmesg: SATA AHCI Phy Power Failed! SATA AHCI Phy Calibration Failed! sw_ahci sw_ahci.0: controller can't to PMP, turning off CAP_PMP sw_ahci sw_ahci.0: forcing PORTS_IMPL to 0x1 sw_ahci sw_ahci.0: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode sw_ahci sw_ahci.0: flags: ncq sntf pm led clo only pio slum part ccc scsi0 : sw_ahci_platform ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0…

Hello, i have problem that text output is cut and I cannot see the command line when writing commands, I have tried vairious settings to disp init but everytime it looks the same, any ideas?

History work: started my work from raspberry pi but recently shifted to orange pi. On raspberry, me used teh UV4I server wif webrtc to broadcast video streaming and send controls through data channels from a web browser to control a robot. My application: So basically my application is a semi-autonomous car wif two cameras.me want to control teh car from a web browser and stream a video of both cameras on teh browser Issues: 1: On orange, pl broadcast streaming from USB cameras to a web browser? 2: Send controls from web browser to orange pi? 3: Teh UL4l drivers are not installable on an orange pi pc so need to find an alternate 4: halp to fi…

does orange pi zero2W support the headsets with built in microphone or not? I do not see any MICINN in the 24 pin connector?

Hello again. I am beating my head against the network configuration again and would dearly love some help. I have two orange pi pc boards with static ip's in the 192.168.1. range. They are only connected to each other. They can ping and ssh each other just fine. I am trying to set up nfs shares between them without success. In /etc/exports I have: /home/martin/folder 192.168.1.*(rw,sync,no_subtree_check,nohide) I have "ALL: 192.168.1." in my /etc/hosts.allow. In /etc/fstab I have: 192.168.1.XXX:/home/martin/folder/from_lev /home/lev/folder/to_martin nfs rw,sync,noauto,user,x-systemd.automount 0 0 And vis-versa on the other pi. The fold…

hi. I have build armbian 5.54 bionic 4.17 and it does not boot. 4.14 works but my intention was build bionic. It is possible to switch back to 4.14 when build armbian myself? Thanks for reply in advanse

Hi, Can anyone share a version of nightly build for Orange Pi Zero Debian Jessie with kernel 4.11.12 or newest for testing? I don't have the possibility to build own version of Armbian but I can try and tests existing distributions armbian. At current, I have use armbian Debian Jessie with kernel 4.11.5 Regards

I need small serwer and i need a AP wifi and dhcp for wifi clients. Anybody can help me and show configuration file to setup Wifi Hotspot and dhcp program (meybe dns lokaly for better communication, my eth0 is slowly) I using Orange Pi Zero

Hello ! In my project I need use 2 spi bus : /dev/spidev1.0 and /dev/spi2.0 /dev/spidev1.0 for 3.5inch rpi display and /dev/spidev2.0 for 8x8 led matrices, such as MAX7219-8x32-MCU-Drive-LED If I am use legacy kernel (3.4.113-sun7i) both spi buses work well But if use mainline kernel (4.14.18-sunxi), I can use only 1 spi bus This is my armbianEnv.txt: overlays=spi-spidev spi1 spi2 param_spidev_spi_bus=1 In this case I can use /dev/spidev1.0 If I set param_spidev_spi_bus=2 I can use /dev/spidev2.0 How to enable 2 spi buses at the same time ?

I'm trying to replicate a flash drive using an ISO file. My system is running the latest Ubuntu next kernel. Here is how I am mounting an ISO: # Mount sudo modprobe g_mass_storage file=/home/pi/mini.iso # Remove sudo rmmod g_mass_storage Here are the two types of results I get from three different images. (Ubuntu net install, Need for speed 2 iso, custom made iso) It's definitely being detected. However it's appearing as either empty partitions or unallocated.

Hey Does this display http://www.ebay.com/itm/192163706724?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT Work with the orange pi zero?

Hi, I've installed armbian on my orange pi +2 and trying to build GrandOrgue. It is depending on the wxWidgets library. I've tried searching apt-get without any luck. Any suggestions? Thank you. -Roy

How install linux-tools for USBIP >usbip WARNING: usbip not found for kernel 5.15.43 You may need to install the following packages for this specific kernel: linux-tools-5.15.43-sunxi linux-cloud-tools-5.15.43-sunxi You may also want to install one of the following packages to keep up to date: linux-tools-sunxi linux-cloud-tools-sunxi >apt install linux-tools-sunxi Reading package lists... Done Building dependency tree... Done Reading state information... Done E: Unable to locate package linux-tools-sunxi I tried linux-cloud-tools-sunxi, linux-tools-5.15.43-sunxi, linux-cloud-tools-5.15.43-sunxi BUT …

This is not solved the only tag I can add is solved. How do I change that I have an orange pi zero 3 and am trying to ssh into this board. Ive written all three minimal files to different 32gb sd cards. After I write the drive I add a blank ssh file and a wpa_supplicante.conf file with my wifi info on it. I install the os with balanaetecher or Rufus(I've tried so many things. I find my IP when I try to ssh doesn't work) but I can ping the zero. I've tried windows 8.1, and 11 plus Linux mint same thing. Could someone please help me? This probably should take 20 minutes but I've been at it for 2.5 days

Hello. I soldered CR2032 battery to BAT1 on Banana pro board. Setup current date and time. But RTC not working. :-( When I restart the board I see old date and time. Please tell me, how can I turn on RTC?

HI.. I have an opi zero and I want to copy the card and use it in a NanoPi Neo I plugged it in and it works but displays Orange Pi Zero on the login screen. What steps should I take to make it work best in the NanoPi Neo? Thanks. V.

Hello, I am really struggling trying to find up to date images (debian jessy) for my Cubieboard4 A80. I'm thinking of selling the hardware now as i'm stuck on the old images which are not being patched: http://dl.cubieboard.org/model/cc-a80/Image/debian-server/ Can you suggest how i should proceed? Any help would be greatly appreciated Thanks, phrag

Hi, does anyone know where I can find a build for linux 5.1 for my orange pi zero 2w. I would like to use fbtft device, so either finding a pre 5.4 linux build, or building one myself (In that case how so because I failed miserably) or an alternative to fbtft. Thank you very much

I flashed the latest Armbian image on my NanoPi Neo 2 Plus's emmc. According to https://linux-sunxi.org/Linux_mainlining_effort I2S is not part of the mailinke kernel for H5. I can use I2S with Friendlyelec's images. However, I prefer Armbian. Is it somehow possible to use I2S with an Armbian image on this board?

I remember that the maximum frequency was 1296Mhz back with Xenial, with kernel 3.x. It even says here Heat is not a problem since i have a large heatsink and temperature controlled fan, i was just curious about why the max frequency was bumped to 1368Mhz on the newer builds. What's the rationale behind it?

At Raspberry Pi (at least on R.Pi 4) it is possibility to set up more than one 1-wire bus. Can that be done on Orange Pi plus 2e with Armbian? uname -a Linux XXXXXXXXXXX 5.15.93-sunxi #23.02.2 SMP Fri Feb 17 23:49:46 UTC 2023 armv7l armv7l armv7l GNU/Linux /boot/armbianEnv.txt verbosity=1 bootlogo=false console=both disp_mode=1920x1080p60 overlay_prefix=sun8i-h3 rootdev=UUID=d908a8da-8d2e-4802-8a05-aaab4f3290bb rootfstype=ext4 overlays=w1-gpio param_w1_pin=PD14 param_w1_pin_int_pullup=0 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u If it is possible: Any tip on configuration will make me happy. And can it be internal pu…

bananapi m1 armbian 5.20 configure smplayer acelered ? thanks

Guys please help me. My orange pi one with Armbian installed and running Pi Hole. The HDMI Output is not working, And when I try to enter this command h3disp [-h/-H] -m [video mode] [-d] [-c [0-2] it say access denied. My point is there's no output this play on my device. I hope someone understand me and help me thank you.

Here is uploaded image showing problem with text overlapping. I googled without success, so if anyone could suggest how to try fixing it. Chromium version is 76.0.3809.100 (Official Build) Built on Ubuntu, running on Ubuntu 16.04 (32-bit) on Orange Pi Lite. It is not big deal, but if there is easy fix why not to try.

I connected FA-CAM202 ( 2M USB cam provided by FriendlyArm) to USB2 pins on Nanopi Duo, The OS is Armbian Bionic mainline kernel 4.14.y The V4l applications output error as Unable to start capture: Input/output error i: Error grabbing frames The dmesg shows uvcvideo: Failed to query (GET_CUR) UVC control 3 on unit 1: -32 uvcvideo: Failed to set UVC commit control : -32 (exp. 26) This Cam FA-CAM202 is worked on PC while other USB CAM such as Logitech works on the same configuration of Nanopi Duo, on USB2. It is more like a driver compatibility is…

Hi there, I am trying to download the lime2 legacy image : https://www.armbian.com/olimex-lime-2/#kernels-archive But the link is dead (error 404). Any chance to get this back up? Or can I use another legacy image and just change the script.bin or is there other things to modify? Thanks Edit : I just found the image on olimex website : ftp://staging.olimex.com/Allwinner_Images/A20-OLinuXino/2.legacy_images_kernel_3.4.x/

Installed Armbian_5.38_Orangepiplus_Ubuntu_xenial_default_3.4.113_desktop. After a while, namely the clock after 5 work OrangePi Plus 2 disappears from the internal network. Do not pass the ping, connection to the SSH. But you can connect from the outside through the routed ports of the router to the SSH. Pings from it pass only to the router (192.168.0.1). Prior to other devices in the local network, pings also do not reach. This is when the internal network disappeared. Before its disappearance with pings and connections on the SSH, there are no problems. What could be the problem? armbianmonitor -u - http://ix.io/17Ni

Hi there I have a banana pi M1 and I have installed Armbian on it. The HDMI output / Display work fine if I have HDMI connected to the HDMI port of BPi and monitor/tv is turned on before Armbian booting process starts. However if I don't have HDMI connected before boot process or Monitor/Tv is not turned on then I don't see the display if I connects the HDMI or turned on Monitor later. It is a problem for me because when I want to connect to display to already booted OS. Does anyone faced this behavior? Please advise.

Hello, my opi+2 sometimes dies after long running times and becomes so hot that I cannot touch it. When I looked to logs, I saw kernel panic errors like, you know, tons of meanless numbers. I can provide any information you want. It's been few hours since I started it but here are logs. http://sprunge.us/jJSK Probably it had had 0.05 15 min load before it died. I couldn't see the message I saw before, probably they got removed from the system after few minutes. I'll send you newer logs after I get accurate errors again. This may take a week, or few days.

After I got my OPiPC+ to finally boot without HDMI, it wouldn't boot in my shop. I originally had it in the bedroom because that's where a convenient HDMI TV was AND that's where the U-Verse router is. In the shop, it went through an HP Procurve 2626 switch but would hang early in the boot process. Logged into the switch and found that most ports were set to "100FDpx". I changed the Pi port to "Auto100" and within seconds, the Pi was booting. Yay! Most people won't have such a problem using ordinary switches. A year ago, I needed more ports in the shop and got a great deal on this one locally. I didn't need 24 ports or the feature set but it was $40.00. T…

hello Armbians, Since over an year I try to use this useless Board. Now i want too switch 3 Relays modules with the gpio system, after an udp command. I installed Wiring pi , gpio readall work gpio write 25 1 , works to the inputt get the value 1 gpio mode 25 out, does not work echo 36 > /sys/class/gpio/export echo out > /sys/class/gpio/gpio36/direction echo 101 > /sys/class/gpio/export echo out > /sys/class/gpio/gpio101/direction the input is without an error but with gpio readall nothing changes this code I wrote to use the gpio with python export38…