Allwinner sunxi

Hello, I have a cubitruck With armbian and it runs the most time fine. Now i'm Not AT Home and the cubi is Out, I See in my router That He is Not running. I Can't connect over ssh. Who can I Look after a reboot when i'm AT Home what is the problem for going down. Thank you

Good Morning, I'm using the 5" LCD of LeMaker designed for Banana Pi. For some reason I changed from legacy Kernel to vanilla kernel. But now in the vanilla kernel touch screen driver isn't available anymore. In legacy kernel it the ft5x_ts module. Is there an other way to make my Display working with touch again? Displays: http://wiki.lemaker.org/BananaPro/Pi:LCD_Module Martin

I noticed that hop lost its cpu bars. I tried to add them but ger error: munmap_chunk(): invalid pointer Anyone else have this problem? Thanks

Hi guys, today i wanted to access my BPi with armbian installed remote with SSH. Terminal says: port 22: Connection refused. I'm able to ping the BPi. At least last week I was able to access the BPi with remote SSH. When i connect it via HDMI i can see the boot process until it says loading kernel - then the screen turns all black and nothing happens anymore. If I try to access some installed webservices, the browser says it can't connect. What can I do?

Is it possible to build Volumio for the Orange Pi PC? I read at the bottom of the build readme on volumio that the armbian_orangepipc_legacy is not booting.. Does somebody know how I can get it to work? I want to transform my Orange Pi in an audio streaming device and volumio seems like a nice choice.

Hello, I'm trying to interface an I2C device to Orange Pi Zero with armbian. By running i2cdetect I obtain the following result: 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- UU -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 70: -- -- -- -- -- -- -- -- I've tried to load …

Hello, Just received this board and I can't get it to turn on if the SD card is present. I've tried several cards and I know them to be good (Samsung Evo 32GB). Any ideas?

Hi there! I just downloaded the available image for the NanoPi Neo root@nanopineo:~# uname -a Linux nanopineo 3.4.112-sun8i #24 SMP PREEMPT Thu Aug 4 20:56:33 CEST 2016 armv7l armv7l armv7l GNU/Linux Audio output is only supported for HDMI (but there is no HDMI connector on the PCB). Analog output and SPDIF are not available in the device list. root@nanopineo:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: sndhdmi [sndhdmi], device 0: SUNXI-HDMIAUDIO sndhdmi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 root@nanopineo:~# It is mentioned that also analog should work, but it is not listed as device as you can see above. root@nanopineo:~# d…

Hello: First, thank you for all your incredible work in armbian. It is really great what you've done so far. And future looks even better. I come here to try to solve a problem that I have with a cheap usb wifi dongle. The dongle usb identifier is: Bus 001 Device 006: ID 0bda:8176 Realtek Semiconductor Corp. RTL8188CUS 802.11n WLAN Adapter With armbian 5.14 (and a fresh install image), I followed the instruction here https://forum.armbian.com/index.php/topic/1237-tutorial-opi-one-wireless-success/ to let it work, without problems. Nice tutorial. My problems began when I was trying to use the same dongle with a fresh installed armbian 5.20. The dongle is not auto…

Hi, Got Debian (8) legacy 3.4.113 server/console and would like to setup a WiFi hotspot. (latest Armbian build 5.51) Seen two methods in Armbian docs 1. -> https://docs.armbian.com/User-Guide_Advanced-Features/#how-to-set-wireless-access-point and via armbian_config in https://docs.armbian.com/User-Guide_Armbian-Config/ 2. -> https://www.youtube.com/watch?v=__BJtInOQFY So I'm a bit buffled about it. Got some questions Got a RTL8188CUS is it suported nowadays? or should I get a specific other one? Do I need to have internet/ethernet/lan connection active during the hotspot creation via armbian_c…

Hi all, I try to compile the driver mt7610u from TP-Link AC600 Archer T2UH USB on BPI-M2 and i have this error: root@bananapim2:~/mt7610u_wifi_sta_v3002_dpo_20130916# make clean && make cp -f os/linux/Makefile.clean os/linux/Makefile make -C os/linux clean make[1]: Entering directory '/root/mt7610u_wifi_sta_v3002_dpo_20130916/os/linux' rm -f ../../common/*.o rm -f ../../common/.*.cmd .*.flags .*.d rm -f ../../os/linux/*.o *.ko *.mod.o *.mod.c rm -f ../../os/linux/.*.cmd .*.flags .*.d rm -fr ../../os/linux/.tmp_versions rm -f ../../os/linux/Module.symvers rm -f ../../os/linux/Modules.symvers rm -f ../../os/linux/Module.markers rm -f ../../os/linux/mo…

I recently updated from very old Armbian image. The update was not smooth so I had to re-image my device with the newest version. After that USB devices cannot be detected at all. I tried USB keyboard and 3D printer (is should looks like generic serial device). Keyboard works perfectly during u-boot but stops working as soon as kernel starts. lsusb doesn't show any devices: $ lsusb -t /: Bus 09.Port 1: Dev 1, Class=root_hub, Driver=musb-hdrc/1p, 480M /: Bus 08.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M /: Bus 07.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M /: Bus 06.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M /: Bus…

It took me a while to get this ILI9340 based LCD monitor working with the Orange Pi Zero until I found a post on this forum that explains how the H2+ ports are mapped to the GPIO numbers in the Linux kernel. So I built an online tool that does the math for you: Here is a map of all the Orange Pi Zero GPIO pins: All the additional details are described in this blog post.

When starting orange pi, it happens that not all the RAM is available. That is, the orange pi has 2 GB of RAM and it is written that there is only 1 GB of RAM. This often happens when restarting using the reboot command. If you turn off the power and reconnect, this problem appears much less often. When 2 gb is available: https://paste.armbian.com/asatebupuw When 1 gb is available: https://paste.armbian.com/bohapeyahi Скрытый текст Скрытый текст

Hello, I'm trying to boot an Orange Pi Plus with Armbian 5.20, and it does not work. I've already check that both OPi and my sdcard work fine, because I can flash and boot the images on orangepi.org site. Besides, I checked how u-boot starts with both Armbian and "debian server" orangepi.org image (both attached)

Hi everybody, I am looking for some advice and help for troubleshooting. Here is the current situation regarding my cubietruck: I have installed Armbian Stretch (mainline kernel 4.14.y or 4.17.y) from here https://www.armbian.com/cubietruck/ on a SD-card using etcher on Ubuntu. If I power up the cubietruck 3 out of 5 times it won't boot. If it starts I can just fine ssh into the system and everything seems to be o.k. But after some time if I start to do something e.g. apt-get update / apt-get upgrade the system will freeze at some point. If i let the cubietruck on it's own it'll run for several hours without freezing. So the problem seems to be related eith…

I have tested the orange pi one xenial. When I say test it is not benchmark tests. I do not know what the numbers say anyway. I open several common programs and watch what htop says. If I run an mp4 file on a media player, libre office and file manager it runs well and htop says about 300mb. It is a 10usd computer and I do not expect it to equal a x86 desktop. If I open firefox, firefox crashes before starting. Because of not enough ram? If I open chromium or midori ram usage goes to 100%. Cpu does not. You cannot really browse sites very well. Youtube videos is the same. Is it becuase 512mb ram is not enough? On my gnulinux x86 n…

With an earlier version of Armbian (Server) I was able to use my Orange Pi Pc + to feed data back to Flightaware, Flight Radar, Planefinder, ADSB Exchange. An upgrade put an end to that in the latest version. Is it possible to get this working in future Upgrades of Armbian? Piaware Install

I am very confused. I don't know where the problem is. Have you ever encountered the same problem? Kernel 4.19.80-sunxi Debian Stretch armbian version 5.98 Orange Pi R1 No third-party hardware was added. Pure R1 bare board Start error message： [ OK ] Started LSB: set CPUFreq kernel parameters. [ 8.670214] Unable to handle kernel NULL pointer dereference at virtual address 00000000 [ 8.681560] pgd = 95d3822c [ 8.684287] [00000000] *pgd=00000000 [ 8.687884] Internal error: Oops: 805 [#1] SMP THUMB2 [ 8.692942] Modules linked in: binfmt_misc 8189es zstd zram lima sun8i_codec_analog snd_soc_simple_card sun8i_adda_pr…

So I have a question... I'd like to manage Li-Ion battery operation on SBCs using the AXP209 power management chip (especially the Banana Pro, as that's what I have...) I soldered a connector to the battery terminals on my BPro for portable operation, and it would be nice to have some kind of solution to raise an alert at low battery charge (like via the onboard LEDs), and automatically call system shutdown at a certain level. Googling has shown that the AXP209 has an i2c interface for sensors, and there are a few scripts for reading battery status here: http://hardware-libre.fr/2014/11/banana-pi-axp209-battery-power-monitoring/ My current plan is to pro…

Hi, I am new to Orange Pi ecosystem. I have a Orange Pi PC 2 running armbian and some times raspbian. I want to use a wifi adapter to this. Since there has been many discussions on which adapter to chose and how to chose I am really confused. Please help me select a wifi adapter which could be installed easily considering that I am a rookie.

I got Armbian (Jessie desktop) working on Orange PI PC. I did "sudo apt-get update" and then "sudo apt-get upgrade" and everything was ok until it said "Compiling headers (please wait)." It has now been on this step for a very, very long time. Is it stuck or does this take a ridiculously long time to complete? Should I shut it down and start over or keep waiting? The green light is staying on steady.

Image of Armbian buster 4.19 Does not work on pine64 A64 2G. There is only a black TV screen. No image problem Armbian Xenial 4.75. help

Hi all, thank you for creating and maintaining Armbian. Makes live much more easier. I installed Armbian 4.5 (Cubietruck Jessie 4.2.3) via UART0. I'm now trying to access at least two further UART Devices (I need serial to an Arduino and to a GPS shield). I understood as Armbian uses the mainline Kernel script.bin is now obsolete and no longer used. Thus I don't know the pinouts for the other UARTs. Is there any documentation? Furthermore I'm not sure if the other UARTs are properly enabled in the Kernel configuration. Linux serial console seem to be on ttyS0 which is working fine: [ 0.000893] console [tty1] enabled Furthermore dmesg shows ttyS0: [ …

I downloaded Armbian_5.59_Orangepizero_Ubuntu_xenial_default_3.4.113.img, and am running it with a 16GB SD card. I am trying to modify the I2C settings, however, when I type `armbian-config`, and select `System`, there is no "Hardware" menu option. This contradicts the documentation: Hardware is supposed to be an option in that menu. This is the current content of the /boot/armbianEnv.txt: verbosity=1 console=both overlay_prefix=sun8i-h3 overlays=usbhost2 usbhost3 rootdev=UUID=54dfde69-e472-48dd-a099-636a963154f3 rootfstype=ext4 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u

Hi there, while trying to solve the issue with OPi PC and rtl8188 (thread link) I managed to get console on the UART interface, nice feature considering my networking issues, btw is there a way to output the kernel messages (dmesg like) to the UART console in real time? I'm asking cos the issue that I'm trying to fix involves system freeze + automatic reboot and I would like to see the logs during the event. I already tried to mess with printk, but it's very likely I've done something wrong.

Hy I tried to play around with the GPIOs and found some nice threads here however I don't get past the modprobe gpio command. I get this error modprobe: FATAL: Module gpio not found in directory /lib/modules/4.14.29-sunxi64 Does my kernel build has no GPIO library inside? Linux 4.14.29-sunxi64 #64 SMP Sat Mar 24 11:13:51 CET 2018 aarch64 GNU/Linux Andy

I've just written an article about my latest cluster build - a 5-node cluster using the Orange Pi Plus2E single board computers - each with 4-core ARM A7 running at 1.3GHz http://climbers.net/sbc/orange-pi-plus-2e-cluster/ Please share the link on Facebook/Twitter/etc if you find it interesting. Thanks

Sorry to ask that, i know there are tons of powerconsumption-discuss an optimization, and tewaking but i got lost. I just need to know how much Ampere a Nanopi NEO drains on fullload (4Cores), connnected with ethernet, no additional USB Hardware in default (no special h3consumtion). Especially boooting (i think armbian is throtteling on boot right?) is also very interessting. I need to buy a Powersupply which is sufficient for 15 NanoPi Boards in min and max consumption. Got very confused in reading the threads... But it seems 5V/2A is just a "be save in every situation" thing, and i think there is a "window" of throtttled booting and full-load 4 Core... So would…

i'm using banana-pi-m2+ already enable i2s0 by changing dtb file in /boot/dtb and can see i2s module load but aplay -l still not showing anybody help? root@bananapim2plus:~# lsmod Module Size Used by snd_soc_hdmi_codec 16384 0 dw_hdmi_i2s_audio 16384 0 sun8i_dw_hdmi 16384 0 dw_hdmi 28672 2 dw_hdmi_i2s_audio,sun8i_dw_hdmi cec 40960 2 dw_hdmi_cec,dw_hdmi sun8i_codec_analog 24576 1 sun4i_codec 32768 3 sun4i_i2s 16384 0 snd_soc_core 118784 4 sun4i_codec,sun4i_i2s,sun8i_codec_analog,snd_soc_hdmi_codec snd_pcm_dmae…

Hey. I'm trying to install octoprint on my Opi Zero +2, using the latest armbian image I found here on the site. Installation works fine, and I get the web interface up and running no problem. But I have connected power to the board on the gpio pins, and want to use the mini-usb to connect to the 3d printer. I have enabled usbhost0-3 in the hardware in armbian-config, but still it seems the printer cannot be reached. I read some older posts regarding other boards, where the solution seemed to be recompiling. Is this a necessity, and if so, could someone please point me to a walkthrough? Regards Anders

Hi. I tried to search the forum but it seems I put wrong search words... How should I install the display so I can run Geany (IDE)? Here is my data http://sprunge.us/WWGg

Hi guys, first I want to thank you for your marvelous work. I've learned much... I've ordered a Nano Pi Neo Air and two Nano Pi Neo from Friendly Arm which arrived last week to build some squeezelite clients and drop them around the house. At the moment I'm just using some cheap USB-C-Media Soundcards but plan to invest in better ones, if the multi-room solution I have in mind is used enough. The Nano Pi Neo (not Air) does exactly what it should using the Ubnuntu Xenial Image from the download page. Cheers! For the Air's I've used the Debian release, don't know really why ;-) At first I've bootet it from a SD-Card after a direct eMMC-Flash using https:…

I should probably start a new thread for this but it seemed appropriate to post here at this time of nght.. So the OPi Zero Plus 2 boards arrived and I duly set up the image on a 8GB SD card, connected the serial TTL to USB adapter and booted. Everything came up fine so I set up the wifi to my local network using nmtui. Again no problems. I did an apt-get update and upgrade and rebooted, all OK again. Having SSHed into the device I get very sluggish performance and pinging from another machine on the lan I see hugely variable pings ie variations from a few ms to over a second. I installed wavemon and it shows a very strong wifi signal (as expected). The ping…

Hi, I am using the Ubuntu desktop image found here https://www.armbian.com/orange-pi-prime/ I am able to start the board, it lights up and connects to the network via ethernet -- I see it come up in my DHCP table and am then able to connect via SSH Docs say to use root:1234 for login, but I get Access denied. I found another forum post that says root is disabled via SSH by default. When I try to connect locally, I get no video from HDMI so I don't know what it's loading up to. I had hoped to be able to configure via SSH but can't get in. Any ideas on how I can proceed? Thank you!

I've already enabled audio-codec in the overlays section I've checked https://linux-sunxi.org/Linux_mainlining_effort#Status_Matrix and saw that audio-codec is supported for h3 since 4.10 Required Information: Linux orangepizero 4.11.9-sun8i #3 SMP Sat Jul 15 00:20:53 CEST 2017 armv7l armv7l armv7l GNU/Linux -->arecord -l shows this pi@orangepizero:~$ arecord -l **** List of CAPTURE Hardware Devices **** card 0: Codec [H3 Audio Codec], device 0: CDC PCM Codec-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 --> running the following command will just hang all the way till ctrl+c is entered pi@orangepizero:~$ arecor…

I bought some 7 inch HDMI screen(800*480 manufacturer-Alientek) with USB controlled touch screen.( http://www.aliexpress.com/item/New-7-inch-USB-Capacitive-Touch-Screen-LCD-Display-HDMI-for-Raspberry-Pi-Pi2-Wholesale/32607731510.html ) HDMI screen can be displayed on Orange Pi One (Armbian 3.4.112-sun8i) using h3disp command. Touch screen could not work on Orange Pi, but that works on linux i386(4.2.0-38-generic). The symptom is as follows. Touch screen is defined ad /dev/usbdev*.* on Orange Pi. but on linux i386 is defined as hidraw device. (I will use uinput or uhid handing this touch screen). ==== orange pi ===== 1)dmesg [ 194.360084] usb 6…

Hi there, i just wanted to report my experience with Igor Pecovnik's debian 4.1.2 image - especially since he says that I2C is untested with Kernel 4.0 and above. I have a PCTV DVB-C/T2 USB Stick (Triplestick 292e) and could make it work with my Cubietruck. I had to use Igor's compile script from the project website in my ubuntu virtual machine on Windows 7 to get the kernel sources and compile the kernel with the required options (the offered SD-Card image lacks support for I2C Multiplexing). To use this stick, you have to compile the kernel with I2C Multiplexing built in, and build the i2c mux modules for the chipset (I compiled all i2c_mux drivers as modules si…

I'm trying to develop a kiosk system using an Orange Pi One (Based on Allwinner H3 - Mali400) running Armbian Xenial To do this I need to develop a full-screen GUI application (I don't have much experience in this area) I'm looking for a professional way to do this, Ive spent about a week trying to get Qt to cross-compile from my laptop but not getting much luck, Any ideas / advice welcome, Andy

Hi Geeks! I am not finding my way out to get console output from Armbian legacy kernel using a USB to Serial adapter, Armbian by default doesn't let me to get the console output on my COM3 port, the cursor remains stuck at blank screen. What extra configuration do I need to do to my Armbian 5.31 orangepi zero with (Linux orangepizero 3.4.113-sun8i #18 SMP PREEMPT Thu Jun 15 02:16:06 CEST 2017 rmv7l armv7l armv7l GNU/Linux) ? I have attached my script.fex(UART config) below.. PLEASE HELP! Thanks.

My cursor in console (not desktop environment) disappeared after apt upgrade from a clean install. Device : orange pi pc Version: ARMBIAN Debian GNU/Linux 8 (jessie) 3.4.112-sun8i I also changed led triggers red one to mmc0 and green to timer. I run apt list>aptlist.txt and attach result to post. it changed a lot i install further packages. aptlist.txt

Trival endevour, though fun and easy to do. Text and diagram taken from zip file attached. Orange Pi Zero fan self adapting to temperature, inside Shenzhen Xunlong Software CO.,Limited manufacturered low profile (non-expansion board version) case. Probably can be used with other SBC's. FanDaemon source provided. Comes with no warranty of any sort. Use at your own risk. The software included works with Mainline Kernel 4.13 Armbian image. Run armbian-config - system - hardware, use arrow keys to highlight "pwm" and press spacebar to [*] enable it. Select save and reboot. Install the fan how you wish. …

Hi, I am using ARMBIAN 5.25 stable Ubuntu 16.04.2 LTS 3.4.113-sun8i on my Nanopi neo air. uname -a says Linux nanopiair 3.4.113-sun8i #10 SMP PREEMPT Thu Feb 23 19:55:00 CET 2017 armv7l armv7l armv7l GNU/Linux I think, since I made the last apt-get upgrade and rebooted, my bluetooth stopped working. lsmod gives: lsmod Module Size Used by bmp085 3487 0 pcf8591 3363 0 snd_usb_audio 80352 0 snd_hwdep 5562 1 snd_usb_audio snd_usbmidi_lib 17545 1 snd_usb_audio snd_rawmidi 17134 1 snd_usbmidi_lib gspca_ov534 9254 0 gspca_main 19688 1 gspca_ov…

hello everyone ! I'm trying to listen music with my orange pi over armbian of course. I have installed VLC and it seems works but not sound . I use the 3,5mm output connected to the amplifier At the moment no sound and no music .... Does anyone know what I have to do ? Thanks in advanced Walter

I'm using Orange Pi One with Armbiab 5.14. And trying to use GPIO (keys) for volume up and down, making game console. Of course, I could read GPIOs status by Wiring Pi, but I couldn't control volume by command. I tried amixer with various parameters, but not change HDMI volume. I'm not sure the usage detail of amixer on Armbian. Please advise me how to change volume by command. It's OK to control by C source, because use C program to read GPIOs!

Hi Back in February '15 I have started to write an instruction about the setup of a BPi-R1 (Router). In the threads of the Forum, the information is scattered and it takes so much time for each to get along. So I thought such a document would help to become not only faster, but to achieve a better result as well, as you can faster spend time with the device and tweak it. My know how is getting better, but things are still missing. If you like to help the 'community' with your know how, please leave comments in the document if you find errors or you find something missing. Google Docs Thank you in advance - for your support Cheers Tido

Hello everyone, First of all, sorry for my bad English. Quick description of my problem: I recently buy three Orange Pi Plus 2E with official case and official AC adapter. On this three cards I want to use Armbian, I use the last version of Armbianfound here: https://www.armbian.com/orange-pi-plus-2e/ Write on SD card with Win32DiskImager. For information, I use a Samsung EVO 16G SD Card, same HDMI cable, same screen and official A/C adapter. For two cards, no problem, boot on Armbian on SD card and install on emmc in 10 minutes, but the last one have some problem... The last card won't boot on SD card with Armbian: black …

Hi. I got NO SIGNAL on my TV during boot after "Starting kernel". Same with dev image builded from tool and with stable image too. Thanks.

fbtft_device - remove after kernel 5.4. How connect SPI TFT to Orange PI PC+ box? ------------------------------------------------------------------------ Welcome to Armbian buster with Linux 5.4.8-sunxi System load: 0.30 0.11 0.04 Up time: 1 min Memory usage: 9 % of 998MB IP: 192.168.0.106 192.168.0.104 CPU temp: 49°C Usage of /: 2% of 59G Last login: Wed Jan 15 19:37:39 2020 from 192.168.0.140 elephant@pls-home:~$ sudo modprobe fbtft_device rotate=90 name=piscreen speed=16000000 gpios=reset:2,dc:71 txbuflen=32768 fps=25 [sudo] password for elephant: modprobe: FATAL: Module fbtft_device not found…

Hey, I was wondering if anyone came across the board layout files. If eagle cad files were available that would be great! I'm assuming that they dont exist.. Or has someone designed a hat or shield for the OPi0? I want to design one and was hoping someone else beat me to it. If not i'll just have to measure it out and make it. I dont want to reinvent the wheel so that would be cool Thanks

Good morning, I am trying to compile the lastest sources for the olinuxino-a20-micro and it fails on building libvdpau. VM guest is Ubuntu Mate 14.04 Here is what the actual error is (I left out the rest of the console log since it was fine): Cloning into '/home/deskwizard/A20-armbian/output/cache/sdcard/tmp/libvdpau-sunxi'... remote: Counting objects: 609, done. remote: Compressing objects: 100% (26/26), done. remote: Total 609 (delta 15), reused 1 (delta 1), pack-reused 582 Receiving objects: 100% (609/609), 299.91 KiB | 0 bytes/s, done. Resolving deltas: 100% (407/407), done. Checking connectivity... done. cc -MD -MP -MQ device.o -fpic -fvisibility=hidde…

Can anyone provide any information on getting the GPU driver working with a Banana Pi M2 Zero? It supposedly has a Mali 400 GPU. In my tests, it seems I am stuck with Mesa software rendering with OpenGL. When I write a program that creates an OpenGL 2.0 ES context, the vendor and renderer both list Mesa and performance is terrible (2-10 fps and GLSL shaders are incorrect) when rendering even the simplest scenes. I am using DRM (Direct Rendering Manager) with boots straight to a CLI and no desktop environment if that makes any difference. With the same code and same conditions on a Raspberry Pi Zero 2 W, OpenGL works perfectly in my tests. I am usin…

I recently picked up an Orange Pi Zero 3 and have been trying to figure out how to get the i2c pins working on the GPIO. The pinout shows pins 2 and 3 (229 and 228 according to the orange pi version of wiringPi) being used to i2c-3. The downloadable images seem to be hodge-podge with the orange-pi-os version based on arch linux. But their instructions appears to be based on earlier orange pi models that had an Orange Pi OS based on armbian which included a 'orangepi-config' command similar to raspi-config. There is no orangepi-config in the arch-based Opi-OS. A third party image from leeboby includes a current buster version of Raspbian but while it contains raspi-co…

Orange Pi Zero 512 MB has a serious wifi problem. After i connect the wifi network, i loose connection and i can't access my zero until i connect with ethernet cable. Interestingly, after i connect ethernet cable, wifi reconnects. i set up my wifi connection with nmtui. Auto connect enabled. I really need to solve this wifi issue. In my thinking there two options, which one is better i don't know. 1 st option: I have to buy wifi adaptor, but i don't know will it solve the problem. (and probably i am going to have driver problem) 2nd option: I am going to write a new thread with python. This code will check wifi connection every 10 seconds, if …

Hello dear comminuty, I have spent the last few days trying to get Hardware-Accelerated Video Decoding Encoding to work on the H618. I have tried everything but it does not work. ffmpeg -input_format mjpeg -video_size 1920x1080 -i /dev/video1 -c:v cedrus264 -f rtsp rtsp://localhost:$RTSP_PORT/$MTX_PATH my goal is to output a rtsp stream from a camera. But I get this ERROR: [cedrus264 @ 0xaaaae53e5170] VE Open error. Error initializing output stream 0:0 -- Error while opening encoder for output stream #0:0 - maybe incorrect parameters such as bit_rate, rate, width or height sudo ffmpeg -f v4l2 -video_size 1280x720 -i …

Hello all, I recently got an orange pi pc plus, and am going to try to use it as a server. However, I do not want it to boot into the desktop GUI as this wastes precious computational resources. How do I force the Pi to boot into the terminal? I am using armbian in order to have the system boot off of the EMMC flash memory. Thanks.

Hello Today i download Orangepi Zero Plus H5 Armbian OS then i tried gpio - i2c test but it's not work ... I did like this sudo apt-get install python-dev sudo apt-get install python-smbus sudo apt-get install i2c-tools sudo apt-get install libi2c-dev sudo nano /etc/modules -> add - i2c-dev, i2c-bcm2708 and i refer https://github.com/longsleep/linux-pine64/pull/17/commits/d915860a9c57a9a3ab3df7775c942ca205c8e16d this site i think adding I2C configs is not problem so give me some advice

Hello ppl. I have an Orange Pi Zero, and I have some issues using UART interface, it give me an output like this: ▒▒▒I▒%E▒Y=7▒g!=7▒Y=5▒[s▒i-''▒Y-9/▒Y=▒▒▒RrR▒▒▒V▒▒ ▒▒▒I▒%E▒Y=7▒c5!e=#=15Q=-▒a#'-#5▒▒▒RrR▒▒▒V▒▒ ▒▒▒I▒%E▒[5=9/57▒=5▒c5!-▒a'▒7==;=5▒57=5%!#▒▒▒▒▒▒▒▒▒▒▒▒▒▒]▒m]▒▒▒▒gY{▒▒}=9/5▒▒5;▒5▒▒▒▒▒▒▒▒▒▒▒▒▒]▒m]▒▒▒▒gY{▒▒}7=#957▒muuu▒▒▒▒▒▒▒▒%=#=15%5#▒7=5%!#▒▒▒▒▒▒▒▒▒▒▒▒▒▒]▒m]▒▒▒▒gY{▒▒7-)▒5%5▒%!#-!▒7=5%!#▒▒▒▒▒▒▒▒▒▒▒▒▒▒]▒m]▒▒▒▒gY{▒▒Y=cW_▒7=5%!#▒▒▒▒▒RrR▒▒▒V▒▒ ▒▒▒I▒%E▒Y=7▒▒59▒▒'!9='▒y▒▒▒R▒%I▒▒▒▒%▒▒ai▒▒▒I▒%E▒Y=7▒gY{…

hello, i am setting up Mopidy in Orange Pi PC2 with armbian. but i found it only playback to the on-board sound card not the USB DAC i connected. root@orangepipc2:/# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Codec [H3 Audio Codec], device 0: CDC PCM Codec-0 [] Subdevices: 0/1 Subdevice #0: subdevice #0 card 1: allwinnerhdmi [allwinner,hdmi], device 0: 1c22800.i2s-i2s-hifi i2s-hifi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 2: Audio [iFi (by AMR) HD USB Audio], device 0: USB Audio [USB Audio] Subdevices: 1/1 Subdevice #0: subdevice #0 i found there is no asound.conf in /etc ... …

Hi, I am new here so please apologize if I am asking already asked question, but I couldn't find the solution. I am trying to install docker on my orange pi zero 3 which is running Armbian (24.2.0-trunk.519) aarch64, kernel version 6.6.15-current-sunxi64. I have found this post, but I was not able to install docker because I found 2 problem that I don't know how to solve. 1. Installing docker using armbian-config does not work. I install armbian-config, run it as su/sudo, choose docker and install. The installer does something and after it's done it returns me to the same screen where I have chosen docker to be installed. So, no confirmation that I hav…

Hi! I didn't find much info in the forum on how to correctly apply RT patch to the Armbian (Orange Pi Zero Plus H5 board). Here is how I did: Built Armbian as follows: 1) I downloaded patch-5.4.22-rt13.patch from https://mirrors.edge.kernel.org/pub/linux/kernel/projects/rt/5.4/ and placed into ~/build/userpatches/kernel/sunxi-current ( I saw from the logs that this is the folder for the builder to search for user patches in my case) 2) Started ./compile.sh --> FULL OS image for flashing --> Show a kernel configuration menu before compilation --> orangepizeroplus (H5) as target board --> current (recommended , which is 5.4.23…

Hello, I need your help to know if it's possible to dump an img to sdcard to make it's working android on my orange pi pc? For testing purpose i 'm linux man and i will say android is a piece of shiit if you ask me! I find an image from Beelink X2 and now i supose i 'm succes to unpack img to fex files... Is needed to modify boot.fex to boot from sdcard (default choice on OPC H3) or just extract system.fex to have my rootfs and take normal armbian bootloader? I dreaming or there is a way like that? (I'm bambi in android world, don't hurt me) ./imgrepacker ../Android/update_X2_v106k4.img ==========================[ START ]==================…

Hello guys, I am having problems with vlc, the video is running out of proportion and it is all over the interface, ie, even minimizing vlc the video is still being shown, I tried to change the codecs but I did not have a satisfactory result, because only the VDPAU works without lags Help me please, sorry for bad English.

Hi forum, I ran an apt-get upgrade a few days back and here linux-image-current-sunxi:armhf was updated from 21.05.6 to 21.08.2 After reboot my SATA was gone. There was nothing in the logs which would have indicated that something is wrong. After I reverted back to 21.05.6 apt-get install linux-image-current-sunxi=21.05.6 apt-get install armbian-firmware=21.05.8 apt-get install linux-dtb-current-sunxi=21.05.6 everything worked again. Has anyone experienced something similar ? Regards Volker

Hi all and thanks for the great work done. I'm trying to install armbian on the eMMC of my NanoPi M1 Plus, the system boot from SD and I create the user then I start the nand-sata-install command. In the "choose an option" I have only "1 Boot from eMMC - system on eMMC" and then I choose ext4. The process complete and I launch the "dd if=/dev/zero of=/dev/mmcblk0 bs=1024 seek=8 count=1" command directly after. The system does not boot anymore with and without the SD inserted. On serial console, in both cases, I get: U-Boot SPL 2017.05-armbian (Jun 13 2017 - 15:14:45) DRAM: 1024 MiB Trying to boot from MMC2 MMC Device 1 not found spl…

Hello, I have just bought a bananaPro. I would like to learn a little by installing armbian and enabling the video acceleration. Currently, I have no LCD display, so I would start to install Debian Wheezy or Debian Jessie (legacy) so that to be able to log in through ssh. Nevertheless, on the download page for bananaPro it is said that "Mali drivers fails to compile". Is this driver mandatory for video acceleration to work ? I figured out it was rather related to cedarX. Then, which armbian image is best suited ? Thanks in advance for some piece of advice. Best regards deb2016

Gents, installed Armbian Bullseye successfully to my Banana Pi M2 Berry. In second step i moved the OS to my attached 2,5 WD RED Sata Harddrive. This was easily possible with the command "sudo nand-sata-install". But now, i see that my /var/log is full, because its located in ZRAM. root@BananaPiM2Berry:/etc/systemd/system# df -h Filesystem Size Used Avail Use% Mounted on udev 431M 0 431M 0% /dev tmpfs 100M 11M 90M 11% /run /dev/sda1 687G 1,3G 651G 1% / tmpfs 500M 0 500M 0% /dev/shm tmpfs 5,0M 4,0K 5,0M 1% /run/lock tmpfs 500M 0 500M 0% /tmp /d…

Hello, it seems like there are no dts files to add support for i2s. How hard would it be to complete this task? The documentation from h6 references support for i2s, and the same in the user manual from Xunlog : http://dl.sumnic.com/download/OrangePi-One-Plus.pdf Edit:After some reading, i2s is not working for now and there's no proper driver yet. Thanks to martinayotte, SPI is working.

Hi all, I have a OrangePi Zero 2 Plus - H5 and installed Armbian buut when i build WiringOP it gives hardware line is missin message. I think so /proc/cpuinfo file is creating by armbian when bord is booting and lines contains all cpu informations. How can i fix the issue? There is any idea? Thanks in advance.

Hi, I used dd command to prepare the SD with download of Cubietruck_Debian_3.8_jessie_3.4.107. It asks to change password immediately, I typed a new password, it gives me Authentication token manipulation error. No way to login. Please help.

Anyone know if this is possible? I've tried this: https://www.raspberrypi.org/forums/viewtopic.php?f=36&t=138730&start=25, but when I go to start hostapd, get this: nl80211: Could not re-add multicast membership for vendor events: -2 (No such file or directory) Could not set channel for kernel driver Interface initialization failed uap0: interface state UNINITIALIZED->DISABLED uap0: AP-DISABLED uap0: Unable to setup interface. uap0: interface state DISABLED->DISABLED uap0: AP-DISABLED hostapd_free_hapd_data: Interface uap0 wasn't started nl80211: deinit ifname=uap0 disabled_11b_rates=0

I use OPI - ONE. I upgraded a package. The CPU temperature become so hot. Welcome to ARMBIAN Debian GNU/Linux 8 (jessie) 3.4.112-sun8i System load: 0.29 Up time: 7 min Memory usage: 11 % of 494Mb IP: 192.168.10.112 192.168.10.116 CPU temp: 60°C Usage of /: 18% of 7.2G Last login: Tue Aug 2 16:42:15 2016 from 192.168.10.101 orangepi@orangepione:~$ cat /etc/armbian-release # PLEASE DO NOT EDIT THIS FILE BOARD=orangepione BOARD_NAME="Orange Pi One" VERSION=5.16 LINUXFAMILY=sun8i BRANCH=default ARCH=arm orangepi@orangepione:~$ cat /sys/devices/virtual/thermal/thermal_zone0/temp 59 orangepi@orangepione:~…

Hi again. After 2 years i want to try configure CanBus on BananaPi and still nothing. I'm continuing my previous post What i do: 1) Paths dtb with this instruction : 2) Load kernel modules: # lsmod | grep can can_raw 20480 1 can_bcm 24576 0 can 20480 2 can_raw,can_bcm sun4i_can 16384 0 can_dev 20480 1 sun4i_can 3) Spawn can0 interface # ip link set can0 type can bitrate 500000 restart-ms 100 triple-sampling on loopback on # ip link set up can0 4) Play with candump / cansend On loopback my messages show in candump, but on arduino…

A couple of weeks ago I took delivery of an Orange Pi Zero Plus 2 H3 it has the form factor I wanted, eMMC support and HDMI which implied I could run a desktop; the H3 was also the variant that seemed to have the best support. Since then I have been trying to get a stable usable desktop environment working. I tried the latest version of Armbian legacy server specifically for this board and that works fine as far as the server version goes so then I tried to add a basic desktop but that didn't work the xOrg driver said there were no screens present and everything I tried after going to Google University failed. Then I tried a couple of distros from the Orange Pi website b…

I just flashed https://dl.armbian.com/nanopiduo/Ubuntu_bionic_next.7z and it doesn't appear to detect the onboard wifi. ip a only shows lo and eth0. I'm going to try the expansion board with Ethernet onboard and see what shows up. OK, just tried this on a adapter board with Ethernet and now there's an eth0 and Wired Connection 1. It appears the eth0 is really the wifi adapter, but nmtui treats it like an Ethernet connection. Same issue with https://dl.armbian.com/nanopiduo/Debian_stretch_next.7z Wifi not detected, but eth0 is detected instead of wlan0.

I remember there where a problem before, shutdown leads to reboot. But now it's the opposite - reboot leads to shutdown. Both gui button or: sudo reboot reboot sudo shutdown -r now sudo init 6 from terminal, or ssh, behave the same. This is on Armbian_5.25_Orangepipc_Ubuntu_xenial_default_3.4.113_desktop / Armbian_5.25_Orangepione_Ubuntu_xenial_default_3.4.113, from download section and self built.

Just run these commands one by one : sudo apt-get install git automake libglib2.0-dev gstreamer0.10-alsa gstreamer0.10-tools libgstreamer0.10-dev libupnp-dev libxml2-dev gstreamer0.10-plugins-base gstreamer0.10-plugins-good gstreamer0.10-fluendo-mp3 gstreamer0.10-pulseaudio pulseaudio git clone https://github.com/hzeller/gmrender-resurrect.git cd gmrender-resurrect ./configure LIBS=-lm make sudo make install gmediarender -f OPI and to add video play back install gstreamer: sudo apt-get install gstreamer1.0 the last command run gmediarender server and now u cat sream audio from phone using any app that support dnla. like this app: https://play.google.com/store…

Hi Igor, I grabbed your 4.1 image, flashed it onto the microsd Card and boot the cubietruck. However, I received the message from my display: Out of specification: 67.5kHz / 60 Hz. The first boot is ok, but after starting the kernel the screen turns black and above mentioned message apears. This happens on the analouge (VGA) input and on the digital input (DVI) as well. How to fix the problem?? I never had any display problems with all your images. never! This is the first time. I might to use your 4.0 image to return into operation again. regards, hitam4450

Hi, I tried to use default audio device, audiocodec hw:0,0 with arecord to record some sounds from mic. The file contains some noise. Any ideas how to activate mic?

As soon as I installed the latest version of the Wheezy I have found that there is some problem with an USB. When I start my Orange PI I can see that USB devices are power supplied from the bus only first a few seconds (when the bootloader is active I guess) and then being switched off. When I plug an USB device and supply it externally then it seems to be working well. My question is: how to switch on power supply of the USB port on my Orange PI? I have read a number of linux forums and found nothing. Very promising seems a command echo on > /sys/bus/usb/devices/usb1/power/level or similar but unfortunately it has no effect. Any hint, guys? Thanks a lot. Radek

i make this post to ask why my orange pi zero reaches easy 85 degrees with a heatsink applied to it. It is placed in a big case. Maybe the temperature reading is wrong? i check temperature with " armbianmonitor -m and i get: Time CPU load %cpu %sys %usr %nice %io %irq CPU 09:28:26: 480MHz 0.55 28% 4% 23% 0% 0% 0% 86°C 09:28:31: 240MHz 0.51 28% 4% 23% 0% 0% 0% 86°C 09:28:36: 480MHz 0.54 28% 4% 23% 0% 0% 0% 86°C what can i do? I'm actually using the orange pi zero as a flight tracker, which is a very cpu and Wi-Fi intensive task, but i think that 86 degrees are too much!!

Hi, recently moonlight embedded has been added support for VDPAU. git repo I tried to compile it with no success. Unfortunately I dont have enough knowledge to make it work. I used Orange Pi one and armbian 5.30 legacy, getting error no video available and no VDPAU. Does anybody managed to run moonlight on Orange Pi?

Hi, Sorry for the newbie question. Is it possible to configure Armbian/OrangePiZero such as it can bridge 2 wireless networks. i.e.: connecting to an existing SSID to gain access to the internet, and at the same time servicing as an access point using another SSID ? And.... how do I do that ? Thanks in advance, Richard

Hello fellow Sunxi forum members, Some may know me from previous Armbian adventures, primarily Orange Pi Zero 3... but I have jumped brands for a change of scenery (but not SoC). When researching H61X based boards for the Zero 2 and Zero 3 development we were doing in another thread, I found the Sipeed LonganPi 3H, which is a relatively new board that took a while to find. My first impressions are that is really well made, and packs a lot in to the Raspberry Pi Zero style profile (although it also has a daughter board). It was shipped quickly in a nice quality hard plastic storage case and.. best of all.. it has two hardware buttons.. so I can rese…

Hello, I installed Armbian 5.84.1 on a A20-OLinuXino-LIME2 a few weeks ago and it works very well: Welcome to ARMBIAN 5.84.1 user-built Ubuntu 18.04.2 LTS 4.19.38-sunxi Today I did a simple apt update && apt upgrade Now the box doesn't boot any longer. On the serial console I see: U-Boot 2019.04-armbian (May 08 2019 - 15:28:02 +0300) Allwinner Technology CPU: Allwinner A20 (SUN7I) Model: A20-OLinuXino-LIME2 Rev.C [...] Starting Armbian memory supported …

first i was able to boot my nanopi from SD card and i was able to access it through SSH. then i was trying to boot my nanopi from EMMC but it was not booting. I already installed a different OS which is specialized for Eflasher (nanopi-neo-core_eflasher_friendlycore-xenial_4.14_armhf_20190522 ) . then i followed the steps carefully: http://wiki.friendlyarm.com/wiki/index. ... i_NEO_Core note : i was using commands since there is no HDMI. I typed : eflasher then i choose 1 and typed yes and waited until the OS was installed successfully and finally i powered off the nanopi, removed the SD card as mentioned, tried to power it on but i coul…

Dear friends. I am trying to initialize my opi lite 2 without success. I'm using a power source, that's ok! I measured the voltage on the RX pin and I have 3.2v. The TX pin at very low voltage. I used a TTL / USB converter to check the debug ttl, but nothing appears. I configured the converter to 3.3v. Can anyone give me any tips on what to do or can I throw the board away already?

Hi All, I have R1 issue again. After lot of experiments and tuning, I decided try to use R1 for real routing :-) It means dual WAN, lot of VLANs, thousands connections, traffic shaping etc. Everything worked well, until yesterday. As whole Europe has real summer these days, working temperature of my R1 is around 30 celsius. I experienced strange issues when traffic is very high. This happen approx. twice a day. System was not restarted, but PPPOE goes down, kernel reinitialize some hardware and everything continues well. Outage is several seconds only. I have to say, that I'm using OpenWrt for this application, but the system is well patched and worked without prob…

Hi, I'm new to the Armbian/Alt PI scene, coming from a RPI Zero W. I'm needing to interact with my PI using a CH340G (is it compatible) USB to TTL dongle. I've also trjed a CH351A device, put it into UART mode. Unfortunately, I get nothing from the PI. Despite using the primary RX/TX pins. I've also tried enabling all of the UART pins using armbian-config, and using another set of pins - to no avail. Please view my setup below. I've run out of ideas of where I'm going wrong. I've tried these images: Armbian_5.90_Nanopineo2_Debian_buster_next_4.19.57 Armbian_5.90_Orangepione_Ubuntu_bionic_next_4.19.57 Refer…

Hello! I recently bought a generic Waveshare 800x480 HDMI (B) USB Touchscreen (rev 3.0), and I'm having problems to make it work properly on Armbian. After a long research, I ended up realizing it's a common problem, and yet I haven't been able to find a solution. It seems there was a patch somewhere, but that link is not available anymore. I'm using the Armbian Desktop 5.31 , running on an Orange Pi One. I've already set it up using h3disp -m 800x480 -d, and tried everything but it won't work. Vertical resolution seems to be right, but horizontal only fits around 3/4 of screen and it's noisy (the same problem everyone seems to have). I have tried this with my P…

Hi, my configuration is: Asus 5V 2A power adapter with usb to 1,7mm cable, Kingston microsd 16GB class 10 with Jessie desktop I can SSH the OPi so I can use H3disp output to HDMI (TV) works fine output to HDMI -> DVI to PC monitor works fine is it possible to use HDMI adapter to DVI, DVI to VGA and get the image to a PC monitor via VGA? i tried it using -d switch but nothing shown on monitor, do I need any special command? or this is not possible at all? please advice, Thanks

I have an Orange Pi Zero 512 H2 with the "original" audio breakout-shield AKA Orange Pi Zero Interface boatd 1.1 like this one http://codelectron.com/intro-to-orange-pi-zero-interface-board/ I loaded the latest Armbian Buster, did apt-get update apt-get upgrade So I have Armbian buster with Linux 5.4.43-sunxi and then tried to send an audio signal to the sound output via speaker-test -twav -c2 root@orangepizero:~# speaker-test -twav -c2 speaker-test 1.1.8 Playback device is default Stream parameters are 48000Hz, S16_LE, 2 channels WAV file(s) ALSA lib confmisc.c:767:(parse_card) cannot…

uname -a : Linux nanopiair 3.4.113-sun8i #18 SMP PREEMPT Thu Jun 15 02:16:06 CEST 2017 armv7l armv7l armv7l GNU/Linux i installed i2c-tools, libi2c-dev, python-smbus but if i try like this i2cdetect -y 0 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- UU -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 70: -- -- --…

Device: Orange Pi +2e. Builds 20.20, 20.05, 20.08 The Armbian Boot Logo is shown only when we boot from SD Card. Do nand-sata-install to eMMC and boot from eMMC, the logo disappears. Could this be a timing issue as it boots faster on eMMC? I do not see any flicker or flash during u-boot. --Rajesh

Hello, please tell me why Chromium does not work on Orange Pi Prime? Здравствуйте, подскажите пожалуйста, почему не работает Chromium на Orange Pi Prime?

Hello, I have an OrangePi Zero H2 which until recently was running almost flawlessly with the Armbian_5.38_Debian_stretch_4_14_14 image. When I did a kernel upgrade using "apt-get dist-upgrade" (because I had earlier the error message ~"failed to Load Kernel Modules", and dist-upgrade was recommended), and this dist-upgrade failed inbetween (probably because of power consumption), the SD card was left in unbootable state. (error msg see below [1]) I concluded that the /boot directory was corrupted, so from a new installation of Armbian_5.38_Debian_stretch_4_14_14 made elsewhere I copied all the /boot directory over to my SD card. This m…

Doohh ... User error - 1PPS wasn't enabled on the GPS. The OPIO Kernel works fine w. 1-PPS $ sudo ppstest /dev/pps0 trying PPS source "/dev/pps0" found PPS source "/dev/pps0" ok, found 1 source(s), now start fetching data... source 0 - assert 1524154630.697340907, sequence: 6793 - clear 0.000000000, sequence: 0 source 0 - assert 1524154631.697261112, sequence: 6794 - clear 0.000000000, sequence: 0 source 0 - assert 1524154632.697166525, sequence: 6795 - clear 0.000000000, sequence: 0 source 0 - assert 1524154633.697084896, sequence: 6796 - clear 0.000000000, sequence: 0 source 0 - assert 1524154634.697017267, sequence: 6797 - clear 0.000000000, sequence: …

I'm currently playing with a Banana Pi M1 + and don't seem to be able to get the GPIO to work. I *think* that I have correctly mapped the IO pins that I am using through the schematic and fex file to find the corrisponding GPIO number for debian. When playing around in /sys/class/gpio I am able to export the GPIO pin that I'm looking for and change it's properties, direction, value etc. However these changes don't seem to appear on the physical IO pins. I noticed that some of the pins that I'm using are shared by UART 2, so I have disabled that in the FEX file but still no luck. I have a feeling that this is probably going to be DTB related, however I'm a …

Hello, I want to use SocketCan on the Banana Pi / Allwinner A20 with the internal CAN interface. I have tested my hardware in the past using can4linux and also have some experience with Socketcan and other interfaces. Configuarion: Armbian root@bananapi:/# uname -r 4.4.1-sunxi loaded the can driver with "modprobe sun4i_can" results in "lsmod": Module Size Used by sun4i_can 5810 0 can_dev 8307 1 sun4i_can And dmesg states: [ 2632.582992] CAN device driver interface But I do not get the can0 device up: root@bananapi:~# ip link set can0 up type can bitrate 500000 Cannot find device "can0" There seems …

Hello, I'd like to use I2S output on my A20, I can see on armbian website but I have no idea on how to activate the HW configuration. I tried to simply plug i2s input and output and type aplay -l but the system can't see any soundcard Can you please help ? Cheers