Allwinner sunxi

Hi, I need to use uart (for a gps receiver) and i2c (for some sensors) for my project via the gpio pins. Fortunately i2c is enabled in the images by default. I hope it is also enabled if I recompile armbian for the orangepi lite by default? Afaik I have to enable UART in the following file: https://github.com/igorpecovnik/lib/blob/master/config/fex/orangepilite.fex . Unfurtunately I do not understand which pins on the gpio header correspond to the ports defined in this file. For example: Can I use UART on any pins on the gpio header? I would like to use UART on the same pins as in https://www.element14.com/community/servlet/JiveServlet/previewBody/73950-102-10-…

Never had a problem with Armbian on my board. After last full upgrade (linux-image-next-sunxi 5.27.170427 etc) system is not booting. I tried with a fresh SD card (image Armbian_5.25_Cubieboard_Debian_jessie_next_4.9.7) - it's booting fine afresh, but also doesn't boot after full upgrade. Below are logs for both cases. Boot with old card: Spoiler U-Boot 2017.01-armbian (Feb 02 2017 - 02:20:16 +0100) Allwinner Technology CPU: Allwinner A10 (SUN4I) Model: Cubietech Cubieboard I2C: ready DRAM: 1 GiB MMC: SUNXI SD/MMC: 0 *** Warning - bad CRC, using default environment In: serial Out: …

Hi, I just started to fiddle around with my Cubietruck (since I exchanged it with a Banana Pi for productive stuff). I had to realize that /sys/devices/system/cpu/cpu0/cpufreq/ is missing and that cpufreq-info outputs "no or unknown cpufreq driver is active on this CPU" correctly. Anyone else seeing this behaviour? Cpufreq support should be back with 4.0? Based on a sysbench run ("sysbench --test=cpu --cpu-max-prime=5000 run --num-threads=2" -- takes 58 seconds) I would suppose it's running not even at 960 MHz (since 960 should finish in less than 54 seconds). I did some iperf tests (not that promising, just 600/650 Mbits/sec) and iozone with my usual test…

I want to use an OPI zero (armbian 5.31) to log data from a smart meter to influxdb. Everything works, but after 5 hrs i cant ssh into the pi - also, no data is written to the db. The pi has heatsinks and the temperature is around 53°C. Now i tried it without the logging and after 5 hrs, the pi was again not reachable (i dont know, if it crashed or only the connection went down). Last try was with a pi lite which showed the same behavior. What could be the problem?

Hello I have Opi lite 2 + 28byj-48 driver and step motor, and I want to play around, but can't find RPi.GPIO for OPi lite 2, how can I make it work ? I find pretty good example with raspberry pi http://www.raspberryproject.pl/en/automation/28byj-48-stepper-motor-raspberry-pi/ , I rearranged GPIOs to fit my board but I have error: File "testy.py", line 4, in <module> import RPi.GPIO as GPIO ModuleNotFoundError: No module named 'RPi' Welcome to ARMBIAN 5.67.181116 nightly Ubuntu 18.04.1 LTS 4.19.2-sunxi64

I just checked the mali blob: mali450r5p001rel0linux1fbdevarm64v8a (fbdev) and this blob is working on the legacy kernel with the proper patches. Nevertheless we may have some stability issues at the current voltage/frequence; Indeed gl-mark2-es-fb crashes around the refract test on my board.

Hey. I'm trying to install octoprint on my Opi Zero +2, using the latest armbian image I found here on the site. Installation works fine, and I get the web interface up and running no problem. But I have connected power to the board on the gpio pins, and want to use the mini-usb to connect to the 3d printer. I have enabled usbhost0-3 in the hardware in armbian-config, but still it seems the printer cannot be reached. I read some older posts regarding other boards, where the solution seemed to be recompiling. Is this a necessity, and if so, could someone please point me to a walkthrough? Regards Anders

armbian for orangepi win and win plus not boot starting kernel ends boot.. why do you build only this one image? No debian 9 images on next and archive folder

After upgrade ubuntu server stops booting and working on Orange Pi Prime (H5, 2GB, WiFi...). Upgrade goes from image (Armbian_5.32.170706_Orangepiprime_Ubuntu_xenial_dev_4.11.8.img) correctly (sudo su... apt-get update, apt-get upgrade, plus install of mc, apache2, mysql, php, phpMySql ... apt-get autoclean). After it is done, I log in using Putty, and the system is still usable but on the login screen there is a message "Kernel upgraded, please restart" (or similar). once logged in I did "init 6" to restart, and Putty is disconnected, and no more response. that is it. Pressing any buttons on the board, disconnecting and reconnecting network, disconnection a…

Hi. My platform is Orange Pi Plus. I connected SATA HDD and installed Armbian. Using nand-sata-install I created the following scenario: boot from SD, system on SATA. I also installed lighttpd. Several days everything works fine and than: ...file system on the root filesystem failed … rebooting automatically due to panic= boot argument... After that the PC just reboots constantly and I can do anything. The only solution I found is to repeat the process of boot SD creation. But after that I need to install everything again. All this I already did for several times... What maybe the reason of this error? Can I exclude the SD card and use eMMC instead? Is there anythi…

board: http://nanopi.io/nanopi-neo-core.html image: Armbian Bionic mainline based kernel 4.19.38 from https://www.armbian.com/nanopi-neo/ There are two SPI separated buses with separated pins on NanoPi Core: SPI0 and SPI1 /boot/armbianEnv.txt: ... overlay-prefix=sun8i-h3 overlays=analog-codec i2c0 spi-spidev uart1 usbhost3 param_spidev_spi_bus=0 ... /dev/spidev0.0 presents How to activate a SPI1?

Hi, after some days with other projects I have updated to newest master and now see this message during installation: [ o.k. ] Installing extra applications and drivers [ o.k. ] Installing linux firmware [ 5.14 ] dpkg: error processing archive /tmp/armbian-firmware_5.14_all.deb (--install): cannot access archive: No such file or directory Errors were encountered while processing: /tmp/armbian-firmware_5.14_all.deb [ o.k. ] Installing [ armbian-hostapd-jessie_5.14_armhf.deb ] invoke-rc.d: policy-rc.d denied execution of stop. dpkg: error processing archive /tmp/armbian-hostapd-jessie_5.14_armhf.deb (--install): cannot access archive: No such file or directory E…

Hello, i try to move it from SD to eMMC on a Orange Pi Zero +2 H5, but without success. Shouldn't be two partion created on eMMC by the nand-sata-install script ? root@orangepizeroplus2:~# fdisk -l /dev/mmcblk2 Disk /dev/mmcblk2: 7.3 GiB, 7818182656 bytes, 15269888 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0xe8c6ce8d Device Boot Start End Sectors Size Id Type /dev/mmcblk2p1 8192 15117183 15108992 7.2G 83 Linux Old UUID: /dev/mmcblk0p1 SD UUID: UUID=85ffa85e-4784-4cfd-93bb-db6f93f8e…

From the armbian page, i downloaded and installed the... Armbian Stretch mainline based kernel 4.19.y Server or light desktop usage scenarios. High level of software maturity ...for my orangpiplus2e. I was able to create the login and password and get sudo powers. But the screen does not go to the GUI, it just stays at the CL. I log in to the 'tty1' login with u and p. I get the "general system configuration beta: armbian-config]. After that it says "host@server: ~$ I don't know what to do next, if anything, or if it is supposed to automatically take me to the GUI desktop. It does not seem to be connected to the interne…

Hi all, I'm new here. Since I bought my OPi One I didn't try any of the official images, but only armbian legacy kernel. The first OPi one I thought it was broken, no led on the board only the eth ones, nothing happend on the screen (homemade power cable with 1.4 plug and a xiaomi ac power adapter 5V 2A almost correctly given, tested with a multimeter). The image was burned on a 4gb kingston micro sd card with etcher formatted with sd formatter. So I bought another one, and I have the same identical issue. So, I started to study and I found out that I could connect to the OPi through SSH. So it what I tried to do all the night. Again image burned with e…

In the "next" Vanilla version of Armbian for CB1: cubie@cubieboard:~/Apps/test-gdb$ uname -a Linux cubieboard 4.5.4-sunxi #1 SMP Wed May 11 16:51:05 EDT 2016 armv7l GNU/Linux cubie@cubieboard:~/Apps/test-gdb$ lsb_release -a No LSB modules are available. Distributor ID: Debian Description: Debian GNU/Linux 8.4 (jessie) Release: 8.4 Codename: jessie The following option is not set in the kernel configuration: CONFIG_OABI_COMPAT=y When this is commented out, debugging fails with an illegal instruction if you do anything other than run, just about. Possibly a coincidence is that "less /proc/config.gz" stops working when that option is set --- dunno. Don't …

I have no need at all for the built in wireless on an Orange Pi Zero board. Is there a way I can disable it entirely to save power? Through the DT or some other means? Thanks!

Hello fellow Sunxi forum members, Some may know me from previous Armbian adventures, primarily Orange Pi Zero 3... but I have jumped brands for a change of scenery (but not SoC). When researching H61X based boards for the Zero 2 and Zero 3 development we were doing in another thread, I found the Sipeed LonganPi 3H, which is a relatively new board that took a while to find. My first impressions are that is really well made, and packs a lot in to the Raspberry Pi Zero style profile (although it also has a daughter board). It was shipped quickly in a nice quality hard plastic storage case and.. best of all.. it has two hardware buttons.. so I can rese…

Hm.. I'll write to you what I have done. Please tell me what's wrong. I have a cubietruck, and I downloaded this one, Legacy Jessie(http://mirror.igorpecovnik.com/Armbian_5.00_Cubietruck_Debian_jessie_3.4.110.zip), and installed it. Install was successful, and worked good. I tried to use nand and SD, and SD only. There were no differences. The result that I want to tell you below, is the same on both cases. ......................... After OS install, I followed this instruction, and I installed several packages. Instruction : wget -q -O - http://upgrade.armbian.com | bash Packages : NFS server Samba server Deluge Daemon(server) I have a 3TB sata disk …

Hello Today i download Orangepi Zero Plus H5 Armbian OS then i tried gpio - i2c test but it's not work ... I did like this sudo apt-get install python-dev sudo apt-get install python-smbus sudo apt-get install i2c-tools sudo apt-get install libi2c-dev sudo nano /etc/modules -> add - i2c-dev, i2c-bcm2708 and i refer https://github.com/longsleep/linux-pine64/pull/17/commits/d915860a9c57a9a3ab3df7775c942ca205c8e16d this site i think adding I2C configs is not problem so give me some advice

Hi. I have received my new Neo Core and would like to flash my image to eMMC. I tried nand-sata-install but it says there is no target. On the Friendly Arm site they have a utility called eflasher, but I think this does not support Armbian. Is there a way to do it or a guide that I have missed? Thanks. J.

Hello. When the browser starts (chromium), the board hangs, the screen turns gray. when in LibreOffice Writer I build graphics or draw figures or lines, the board hangs, the screen turns gray. load on the processor and memory for 100% console applications - all in order. What is the problem?

Hi! I didn't find much info in the forum on how to correctly apply RT patch to the Armbian (Orange Pi Zero Plus H5 board). Here is how I did: Built Armbian as follows: 1) I downloaded patch-5.4.22-rt13.patch from https://mirrors.edge.kernel.org/pub/linux/kernel/projects/rt/5.4/ and placed into ~/build/userpatches/kernel/sunxi-current ( I saw from the logs that this is the folder for the builder to search for user patches in my case) 2) Started ./compile.sh --> FULL OS image for flashing --> Show a kernel configuration menu before compilation --> orangepizeroplus (H5) as target board --> current (recommended , which is 5.4.23…

Hello, I do images of Debian Jessie with Desktop anf in the end it do image but I have : [ o.k. ] Installing desktop-extras for sunxi [ sunxi ] E: Impossible de trouver le paquet libdri2-1 dpkg: des problèmes de dépendances empêchent la configuration de mpv : mpv dépend de libbs2b0 ; cependant : Le paquet libbs2b0 n'est pas installé. mpv dépend de libcdio-cdda1 (>= 0.83) ; cependant : Le paquet libcdio-cdda1 n'est pas installé. mpv dépend de libcdio-paranoia1 (>= 0.83) ; cependant : Le paquet libcdio-paranoia1 n'est pas installé. mpv dépend de libfdk-aac0 (>= 0.1.1) ; cependant : Le paquet libfdk-aac0 n'est pas installé. mpv dépen…

Hello, I am the owner of this board. I have some questions for developers 1. when will the reboot fix and what is the problem? 2 after last upgrading to 5.59.180904, armbian is no longer loaded at all. log the error: [ 2.319975] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.18 [ 2.328255] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.335488] usb usb5: Product: MUSB HDRC host driver [ 2.340462] usb usb5: Manufacturer: Linux 4.18.5-sunxi64 musb-hcd [ 2.346562] usb usb5: SerialNumber: musb-hdrc.1.auto [ 2.351855] hub 5-0:1.0: USB hub found [ 2.355641] hub 5-0:1.0: 1 port detected [ 2…

Hello, Upgrading uboot 5.25 to 5.35 on Armbian_5.25_Lime2_Ubuntu_xenial_default_3.4.113 fail to boot at next reboot. It's a lime2 Nand with SD card system, last rev hardware I don't find any solutions for the moment, because serial output doesn't output very much ... here is the 5.35 boot U-Boot SPL 2017.09-armbian (Nov 22 2017 - 15:21:35) DRAM: 1024 MiB CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 Trying to boot from MMC1 U-Boot 2017.09-armbian (Nov 22 2017 - 15:21:35 +0100) Allwinner Technology CPU: Allwinner A20 (SUN7I) Model: Olimex A20-OLinuXino-LIME2-eMMC I2C: ready DRAM: 1 GiB MMC: SUNXI SD/MMC: 0, SUNXI SD/MMC: 1 *** Warni…

Hello, I look for the instructions for use to install the new Kernel 3.4.108 for Debian Jessie on Olimex Lime 2 please. He was posted here: http://www.armbian.com/olimex-lime-2/ But he(it) disappeared. He explained us the lines of commands(orders) to create both files : "boot.scr" and "boot.cmd". Could you tell me where are these instructions for use please? Thank you very much... (sorry for bad english, i'm a froggy)

Just got mine Prime and installed on microsd Armbian-server for that. After setting up root password and new user, have edited /etc/network/interfaces to have uncommented these lines source /etc/network/interfaces.d/* auto eth0 iface eth0 inet static address 192.168.0.106 netmask 255.255.255.0 gateway 192.168.0.1 dns-nameservers 8.8.8.8 8.8.4.4 auto lo iface lo inet loopback every manual says it should be easy like that... but it doesn't work where to dig next?

orange pi one h3 512mo ram didn't boot up and it stop at starting kernel this happend for both armbian version in the armbian website , i tryed also a version from the official website of orange pi one and it pass this step but show black screen .is there any image work properlly on orange pi one H3 please hekp

Hello If I would like to build a specific Kernel (5.1.15-sunxi64) that I have already made before and just want to add some patches to the kernel, what is the right command? ./compile.sh BOARD=bananapim64 BRANCH=5.1.15y RELEASE=bionic BUILD_MINIMAL=no BUILD_DESKTOP=no KERNEL_ONLY=no KERNEL_CONFIGURE=no INSTALL_HEADERS=yes

Hi everyone, First of allm thank you for all the stuff on your site / forum, I recently decided to give a try to an orange pi board, and chose the orange pi plus. I have downloaded and installed the raw file of jessie desktop found on the site, and then tried to launch it. At the first startup, I had a message about my ethernet connector, gmac probed... no PHY... and then the process continue, the card shut down. I unplug/plug in the power supply, and then the board correctly boot up, and I was able to log in. The wifi is working fine (I use it now), but I don't have the ethernet connection. The ethernet cable is plug in, my ISP's router has a DHCP server…

Hi. Recently i upgraded to Armbian_5.65_Orangepilite_Debian_stretch_next_4.14.78 and i have two problems. I can not read the thermal zones properly with neither of those: cat /sys/class/thermal/thermal_zone0/temp cat /sys/devices/virtual/thermal/thermal_zone0/temp cat /etc/armbianmonitor/datasources/soctemp because i have results like "30371". But when the system starts the correct temperature is displayed: Welcome to ARMBIAN 5.73 stable Debian GNU/Linux 9 (stretch) 4.19.20-sunxi System load: 0.07 0.15 0.10 Up time: 10 min Memory usage: 29 % of 493MB IP: 192.168.1.46 CPU temp: 33°C Usage of /: 10% of 15G and with armbianmonit…

The topic is no longer new, but I have not found the reason and its solution! If you turn off the power (just pull out the wire) then you can get a non-working system. As I noticed, the files opened at the time of launch are broken. And some files such as /etc/boot/armbianEnv.txt in general, they are recorded with some kind of garbage!!! Because of this, your settings fly off! For example, I use ttys1 and this option is registered armbianEnv.txt , but after the power loss, there is just terrible garbage in this file, as if the memory dump fell there!!! For example, I still use dotnet, so it also breaks down and does not start anymore!! When y…

Hi all, any advice to enable i2s audio in mainline kernel? I'm on 5.23 cubietruck mainline v4.8.6. Cant find any reference to write DTS...any help would be appreciated. Thank you

Well, the title is self explanatory. I am trying the new stable release for the Orange PI win from armbian (thank you guys!) but when booting for the first time in headless mode via SSH through Ethernet cable it gets stuck at "Enter new UNIX password". I put the new password and nothing happens. If I unplug the cable to force the SSH server to close the connection and then I plug it back again, the password is kept the old one (default 1234) and the problem repeats. After some tests I finally got to change the password, but it gets stuck after, or even before sometimes if I reboot. It seems that the SSH tunnel is simply not stable. I should mention that the configura…

At the moment it seems that python library to manage the gpio is working well I'm trying with wiringPi with C++ under netbeans but it doesn't work . The compiler is the g++ and other parameters are ok ...I think But how to use this package with C/C++ ? In my project I include the #include <wiringPi.h> And netbeans compiles without any error, that's ok . But when I add this line of code wiringPiSetup () ; I get two errors .Into the header file this function is declared as external . I think there is a conflict because my project is C++ but the library is in C and then mistake when compile . Using the terminal I type make blink and then ./blin…

Hi, first of all thanks a lot for every contributor, this is a great project, I'm an absolute fan! I'm running Armbian on an orange pi 2, everything works fine for a while. I'm running a homegrown python script with flask, this one works too. But after ~1-x hours, I can't connect anymore to my web service. This could be my problem, but in fact, neither SSH works. So I found these things, my script tells me this: ---------------------------------------- Exception happened during processing of request from ('192.168.0.158', 59734) Traceback (most recent call last): File "/usr/lib/python2.7/SocketServer.py", line 290, in …

Hello, I'm new with armbian and I want to generate an image with a specific kernel version. Is it possible? I found the LIB_TAG but it's now deprecated, is there a replacement parameter? Thank you, Guillaume

Hello readers, i just tried out the new jessie with 4.0.4. But after start it stops @: ---- Welcome to Debian GNU/LINUX 8 (jessie)! [TIME] Timed out waiting for device dev-ttyS0.device. [DEPEND] Dependency failed for Serial Getty on ttyS0. ----- What am I doing wrong ? Also no LED´s a flickering. Thank you for advice

Hi, With an Orange Pi Zero Plus I‘d like to run a DLNA (UPnP) music server for streaming flac files - means music only - to certain clients via LAN, for instance a network AV receiver. Therefore, 100 MBit/s should be sufficient. How to limit the OPi0+ network speed to 100 MBit? And to switch off Wifi also? ... ... for minimizing power consumption. Presupposed Armbian + OMV (+ miniDLNA plugin) installed. Thanks, Joe

Hello, I need help for my Orange Pi Plus2, i have found a Ubuntu 15.10 (Wily) *.img that works on my board. Ubuntu_wily_mini.img.xz https://mega.nz/#F!wh8l2BjK!OBep3nMldBletvNNwkH2Jg Also installed on my board but i have a problem there are no drivers for the ethernet (Lan / W-Lan) clould someone help me to compile this image with the right drivers. Please note i dont want a desktop interface only the server version of ubuntu. Thanks a lot.

Hello guys, I am trying to use hardware flow control over the uart 1 of a nanopi neo core that I am using with a minishield. The GPIO pins of RX,TX,RTS and CTS of uart 1 based on this documentation (http://wiki.friendlyarm.com/wiki/index.php/Mini_Shield_for_NanoPi_NEO_Core/Core2) are G6,G7,G8 and G9. First of all I downloaded WiringNP in order to see the status of each GPIO. Before activating the rts cts on uart1, the figure "beforeActivatingRTSCTS" is the output of the command "gpio readall" . Then I added to the /boot/armbianEnv.txt the following overlay : param_uart1_rtscts=1 I rebooted the nanopi. After reboot, the figure "Aft…

So I have been struggling with my new Orange Pi Zero the last couple of days, I tried everything but was unable to get it working. I followed all debugging steps I could find through google and through this form so i am at the end of the rode. I have tried 2 different SD cards, on which I ran h2testw 1.4 with the following result: Spoiler Card 1: Test finished without errors. You can now delete the test files *.h2w or verify them again. Writing speed: 20.3 MByte/s Reading speed: 63.9 MByte/s H2testw v1.4 Card 2: Test finished without errors. You can now delete the test fi…

I am trying to connect an SATA -> USB DVD-R drive to OPi3, but it fails, K3b complains about "no drive". Here is syslog: Aug 15 22:12:31 orangepi3 kernel: [34203.588120] usb 3-1.1: new high-speed USB device number 8 using xhci-hcd Aug 15 22:12:31 orangepi3 kernel: [34203.712687] usb 3-1.1: New USB device found, idVendor=13fd, idProduct=084 0, bcdDevice= 1.14 Aug 15 22:12:31 orangepi3 kernel: [34203.712695] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNu mber=3 Aug 15 22:12:31 orangepi3 kernel: [34203.712698] usb 3-1.1: Product: External Aug 15 22:12:31 orangepi3 kernel: [34203.712701] usb 3-1.1: Manufacturer: Generic Aug 15 22:12:31 orange…

Hello! Please help me. The error occurs with both the camera and even without a camera: 1) root@orangepione:~# modprobe gc2035 root@orangepione:~# modprobe -v vfe_v4l2 insmod /lib/modules/3.4.113-sun8i/kernel/drivers/media/video/videobuf-core.ko insmod /lib/modules/3.4.113-sun8i/kernel/drivers/media/video/videobuf-dma-contig.ko insmod /lib/modules/3.4.113-sun8i/kernel/drivers/media/video/sunxi-vfe/vfe_v4l2.ko root@orangepione:~# dmesg ... [ 341.296379] [ISP] isp platform_id = 5! [ 341.368184] [CSI_ERR][GC2035]sensor_read err at sensor_detect! [ 341.368199] [CSI_ERR][GC2035]chip found is not an target chip. Video device is not created in /dev directory. -----…

Hello , I have setup a banana pi with armbian: Linux bananapi 4.3.3-sunxi #3 SMP Mon Dec 28 11:27:16 CET 2015 armv7l GNU/Linux I wuld like to setup a wifi access point from a rtl wifi dongle. Realtek Semiconductor Corp. RTL8192CU 802.11n WLAN Adapter First, I have tried with bananian and it was working perfectly. But I have also a tv adapter not working with bananian, kernel 3.4 seems not support it. With armbian vanilla, the tv adapter is supported but it seems to have an issue with the wifi dongle driver. When I start hostapd-rt, I have the following errors: drv->ifindex=5 l2_sock_recv==l2_sock_xmit=0x0x766b0 ioctl[SIOCSIWMODE]: Invalid argument Co…

Hi I want use spi in slave mode, how i can enable slave? cat /boot/armbianEnv.txt verbosity=1 console=serial overlay_prefix=sun50i-h5 overlays=spi-add-cs1 spi-jedec-nor spi-spidev param_spidev_spi_bus=0 param_spidev_max_freq=100000000 rootdev=UUID=47313251-44b3-4a77-aef5-c53397e3a685 rootfstype=ext4 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u

Hi, i am using orangepi PC (H3). i had tried follow link, test.mp4 file created successfully. (video fine). https://github.com/avafinger/ffmpeg_cedrus264_H3 now, i want to real time(20~30 fps) capture for /dev/video0 (gc2035). i tried mpv with gc2035, but it didn't worked. i want real time video capture using cedrus264. orangepi@OrangePI:~/tmp$ mpv tv:// Playing: tv:// [tv] Selected driver: v4l2 [tv] name: Video 4 Linux 2 input [tv] v4l2: your device driver does not support VIDIOC_G_STD ioctl, VIDIOC_G_PARM was used instead. [tv] Selected device: sunxi-vfe [tv] Capabilities: video capture read/write streaming […

Hi! I use this board since jun/2019 with Armbian 5.90 and kernel 5.1.15 (all OK except HDMI audio). In these 6 months tried to update kernel image few times, 5.2.x some months ago and now 5.5.0, but not more 1920x1080 support, the maximum is 1280x1024. Xrandr not show as supported mode anymore, whats happen? This is related to u-boot? I think can not read EDID, because no monitor model name is shown. Another question is, now in 5.5.x I can see HDMI audio device, but still can't listen, what left to be developed?

Hi Igor, while trying to reproduce/fixing my boot problem, I stumbled across some weird things regarding your new update script. I've put a complete new image on sd-card only (Armbian_4.5_Cubietruck_Ubuntu_trusty_4.2.3) which works fine, boots and reboots. Then I've tried to use your update script which I called via: wget -q -O - http://upgrade.armbian.com | bash with the letter O and a blank between the minus and http, is this correct? First strange thing I noticed is, that it starts but doesn't run through completely. It ends with this output: Don't think that this should be the normal behaviour!? And remember that this wasn't the case when I tried…

at OPI PC with kernel Linux orangepipc 3.4.112-sun8i #30 SMP PREEMPT Sat Apr 30 19:49:10 CEST 2016 armv7l GNU/Linux before the last kernel update we use rt2800 wifi dongle. dmesg | grep usb - shows this output: [ 0.963044] usbhid: USB HID core driver [ 169.650117] usb 3-1: new high-speed USB device number 2 using sunxi-ehci [ 169.948904] usbcore: registered new interface driver rt2870 after the last kernel update with apt-get update in 2016-06-08 which include these updates: Start-Date: 2016-06-08 10:31:45 Commandline: apt-get upgrade Upgrade: linux-jessie-root-orangepih3:armhf (5.10, 5.11), libavdevice53:armhf (0.8.17-2+rpi1, 0.8.17-2+rpi1+deb7u1), f…

Hi, I was just wondering if anyone else out there with a Win+ has this issue .... when I install from an image file all works well, WIFI etc all good. But when I upgrade the install wlan0 etc has gone. ifconfig doesnt show it, lsmod shows the brcmfmac/cfg80211 I've tried it with a few of the recent image files systemctl status systemd-modules-load systemd-modules-load[1693]: Failed to find module 'lp' systemd-modules-load[1693]: Failed to find module 'ppdev' systemd-modules-load[1693]: Failed to find module 'parport_pc' root@zoot: lsmod Module Size Used by ipt_MASQUERADE …

The old 0.14.0 version doesn't work well with subtitles, ending up with subtitles drawing on top of each others, when the text is moving fast. Is there any build I could download and install? Or some other workaround? Edit: Kodi draws the subtitles correctly, but it has pretty awful screen tearing. Using black bloxes instead of just some outline on the subtitles does work, but it's not an acceptable fix to me. So, it would be great it was possible to use whatever kodi uses to draw the subtitles, but then use mpv to draw the video.

Hi, as I need to use an OS allowing me to have Cozy and Gladys (both node.js) on my router (using them it as server) I tried to use armbian for the first time. I sucessfully installed armbian on a SD Card and boot it. My BPi-R1 is not connected to a display or other periherals (keyboard / mouse). Because I do not have those materials I sold them. It is just connected with RJ45 and has a HDD connected on the SATA port. I then connected my modem RJ45 connector to my BPi-R1 on the WAN port. I connected my computer on the first port (near the WAN one). I saw my laptop do not get an IP certainly due to the fact that LAN port seems to be manually activated. …

This has been replaced by: User Space IO get more details on this thread. Well, it's time to say goodbye to sysfs and hello to libgpiod! @zador.blood.stained pointed me in the right direction, but you need to do one little hack I'll explain below involving compiler_types.h. I tested this on a NanoPi Duo, but it should work on any mainline Armbian release (and other distros as well) as long as the kernel is >= 4.8. Try ls /dev/gpiochip* and see if anything is listed. If so, then proceed. I'm continuing work on my Github site https://github.com/sgjava/libgpiod-extra, so please report any issues there. There is an Armbian install script t…

Since updating to the (vanilla) 4.3.3 kernel, my Cubietruck has not read the real-time clock at boot time. This causes all log messages to show "Jan 1 01:00:10" until the NTP daemon kicks in. It also causes cron to remain confused about daylight savings until it is restarted. Looking at the release history at http://www.armbian.com/logbook/I see that v4.81 / 28.12.2015 includes a fix for a "Jessie RTC bug". Unfortunately it seems that this release has introduced an RTC bug! What was the fix, and is there an option I can use to reverse it? Before the update the boot messages looked like this: Jan 14 00:45:07 localhost kernel: [ 0.000000] Linux version…

Took me over a year to isolate this bug. Randomly, I have found that /boot/armbianEnv.txt had unconsistent content. Examples: .tty1tty1LOGIN.8 ¹[fU7ttyS0tyS0LOGINusbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u network={ ssid="Demaine_40_Grd_Rue_Chambre-BP" #psk="1234567890" psk=693d195a3bf2ab6defbcc0b54604ced4286a067996138db6dc793d8648f67d79 } usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u network={ ssid="fabste" #psk="1234567890" psk=95342031a4b28398045e1761f9c64f8454902e80d37102e5476fa…

So I've gone ahead and got an Orange Pi PC. I've already been using a few Raspberry Pi boards, as well as the Odroid C2. I wanted to see what the Orange looks like in comparison. It fails to boot properly. I've read a few things around the web, tried the official as well as a few of the Loboris images, including the Raspbian, Jessie and Slackware ones; used the newer script.bin and uImages, etc. But still no go. The board isn't dead, the power LED and the other 2 LEDs near the ethernet port light up. I get activity through the debug serial port, but that's about it. No image through the HDMI, no DHCP request to my router (I connected it through a wired connection…

From time to time I see a message like this in my log files: 2025-06-05T11:29:33.367636+02:00 bananapipro2 kernel: [934985.549250] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z) replay-kernel-logs(R) The system continues to work (although I remember that it stooped at this point in older releases). Is there any action required? I am afra…

hello there! after update rpimonitor to 2.13-beta6 by Xavier Berger, can't monitor, any temperature , memory usage. But CPU freq, Sd card and network work OK. my spec : Orange pi pc + ARMBIAN 5.38 stable Ubuntu 16.04.5 LTS 3.4.113-sun8i

Hi Igor, I've read about your latest image and I'd like to obtain the stability fixes you've made. Is there a way to get this without doing a whole fresh installation? Idoubt that an aptitude upgrade will bring me these changes!? Thanks and best regards, Jochen

Hi, I've been using Armbian for three years on some work's project and this is the first time I see this issue. Basically I have an image of the operative system and all the programs and scripts already saved in it, so when I have to prepare a new SD card I just use the command "dd" and then I modify some registry stuff specific for the object I'm creating. It has always worked without problem, but now we bought a new batch of SD cards and I'm facing this issue: the dd command goes succesfully and if I mount the partitions after it has finished I can see all my data, but when I boot the system sometimes I get some errors. Here is the last part of the…

Hi, I'm Olivier, french engineer, and i have bought an orangepi plus card in april. I use linux (x86) since 1994 Sorry for my bad english ... I was happy to find Armbian because linux images provided by xunlong have many security problems (example / and all system directory aren't owned by root but by orangepi user). Thank for your work on Armbian. My Orangepi + has been installed with a 5.10 armbian image (Armbian_5.10_Orangepiplus_Debian_jessie_3.4.112) and run perfectly. I wanted upgrade to 5.20 and since the card doesn't boot anymore. I can boot with the native android on NAND memory but I can't boot on SDcard. When I boot on sdcard, only gr…

Hey there, I am a long time user of your armbian operating system. It is great, I am using it for a simple home NAS system. But I have found one problem with armbian, which is very annoying: My standard Banana Pi keeps loosing the HDD Ive connected over Sata. It is a 3,5" Seagate Barracude 3TB drive formated as Ext4. It gets 5V and 12V power and runs quite perfect, as long as it has something to do. It spins up and down as I configured it. But when I leave the pi for a longer time period unattended (no workload), and the harddrive stays in spindown-mode too long, it wont identify the HDD anymore. The mount point and the /dev/sda are gone. I need to powercycle t…

Hi, I have a problem with an OrangePi that I have set up to host Octoprint for my 3d printer. It connects to the wifi just fine(receives wifi IP and I can ping e.g. google.com), but this is all checked through a serial interface, because I can not connect via my network(through SSH) and I can not see the webserver that Octoprint should host. I can't even ping the OrangePi from my computer. What solves the problem for me is to ping my computer from the OrangePi(via serial console). First then I can connect via SSH and see the web page or ping the OrangePi from my computer. If I plug in ethernet to the OrangePi, there is no problem. I have searched …

Hi, Just did a fresh 5.49 build, OPi PC, legacy, Ubuntu console/server. Ethernet network is not working (out of the box) It does not get an IPv4 address automatically Tried to and got it enabled via nmtui, it was showing an 'eth0' as activated and a 'Wired connection 1' as deactivated. I activated the wired connection1, it automatically removed the eth0 from the list and then it has taken an IP address. Did a reboot, though after reboot it was again not working, it did not retained settings. NMTUI show again eth0 as activated and 'wired connection' as deactivated. And no IP address is given to the b…

Hello, Since the kernel 5.3, used for ARMBIAN reached EOL: http://lkml.iu.edu/hypermail/linux/kernel/1912.2/04661.html Is there any movement to a new kernel version?

Dear Igor, I made a custom 4.1 kernel with your script, where a staging driver (mn88472) is included. I'am trying to use an Astrometa DVB stick with mn88472 demodulator, but it's not working. Everything seems fine, no errors, every module loaded, firmware is in it's place. If I run wscan, it goes through every frequency, but it doesn't find any channel. The most weird thing is that two or three times it worked, but I don't know why, and I am not able to reproduce it. (I am using DVB-C so it's sure that the signal is fine) I investigated the source code of the mn88472 module, and as I see, I should get a notice about the firmware load status. An error message o…

Hi All, I'm trying to get usb otg enabled as host mode to add, for instance, a keyboard with a powered hub (I know otg is not delivering power or at least I don't want to drain more power with the otg) I'm using vanilla kernel 4.8.4 so I kind of expect otg enabled as host mode by default. Anyway, I get into dts and make sure this section: usb@01c13000 { compatible = "allwinner,sun4i-a10-musb"; reg = <0x1c13000 0x400>; clocks = <0x2 0x0>; interrupts = <0x0 0x26 0x4>; interrupt-names = "mc"; phys = <0x30 0x0>; phy-names = "usb"; extcon = <0x30 0x0>; allwinner,sram = <0x31 0x1>; status = "okay"; dr_mode = "host"; linux,phandle = …

I am trying to install my newly bought D-Link DWA-131 E1 on my Orange Pi PC with theLinux orangepipc 4.14.18-sunxi #24 SMP Fri Feb 9 16:24:32 CET 2018 armv7l GNU/Linux. I googled from the internet and there are so many guides which will not work for me. I almost messed up my OS and the installation still failed. I already re-flash the microSD card with a new "Linux orangepipc 4.14.18-sunxi #24 SMP Fri Feb 9 16:24:32 CET 2018 armv7l GNU/Linux". I am here looking for help if some one experts here can guide me through out the installation. I really appreciated for your help and thank you in advance. Best regards, …

Hi All! OS - ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.18-sunxi OPI Zero. armbianEnv.txt : overlay_prefix=sun8i-h3 overlays=uart2 param_uart2_rtscts=1 RTS CTS don't work I check the work of the logical analyzer. The line RTS does not change the voltage during the request for data transmission. This is necessary for me to connect the MAX485 chip to UART2 OPI Zero.

During installation new Image show on screen following problems: Failed to retrieve unit state: Transport endpoint is not connected _ _ _ _ _ /_\ _ _ _ __ | |__(_)__ _ _ _ __ ___ _ __ _ __ _ _ _ _ (_) |_ _ _ / _ \| '_| ' \| '_ \ / _` | ' \ / _/ _ \ ' \| ' \ || | ' \| | _| || | /_/ \_\_| |_|_|_|_.__/_\__,_|_||_|_\__\___/_|_|_|_|_|_\_,_|_||_|_|\__|\_, | |___| |__/ v26.2 rolling for Orange Pi Zero running Armbian Linux 6.12.63-current-sunxi Packages: Debian stable (trixie) Support: …

Hi all. I followed this tutorial and I got the AP and client mode working. wlan0 using the onboard wifi as the AP and wlan1 using a usb dongle as the client connecting to my wifi network. But when I connect to the PI and got an IP address via dnsmasq I am not able to get to the pi its self. I can not access anything on the PI. I have a web server running on it. How do I get to the services on the Pi it self via the AP I created. Basically what I want to do is have the client connect to the wifi network if there is one or if the pi is in range of the wifi network. But then if there is no network then I want to connect to the…

Hello, I am using Armbian nightly legacy Jessie 3.4.113 build and it seems Mali drivers are included. Please, How should I set values in boot.cmd and boot.scr to mali HW acceleration work properly? I checked this site http://linux-sunxi.org/KernelArgumentsand tried to place something like "sunxi_ve_mem_reserve=64 cma=96 sunxi_g2d_mem_reserve=64 sunxi_fb_mem_reserve=32" to this file on setenv line but armbian fails to boot. I would like to use HW acceleration in VLC. Thank you.

I have an ADC and DAC board built for Raspberry Pi which has 2 slaves on the SPI bus, requiring ce0 and ce1. This works fine on the Raspberry pi 3, which installs devices /dev/spidev0.0 and also /dev/spidev/0.1, to access each slave. On the OPi PC I can access slave 0, but not slave 1. In /dev on the Opi there is only a single spidev device: /dev/spidev0.0 and no spidev0.1 device. I have modified the script.bin (I am using Armbian legacy OS - Armbian_5.14_Orangepipc_Debian_jessie_3.4.112_desktop) by editing the .fex (and making a new script.bin) to add a spi_cs1 = port:PC07<3><default><default><default> line. But adding this prevents any spide…

Hello, sorry but my english is not best. I tried to search forum for these problems, but I do not found the answers First problem is that serial console do not work for me, just random symbols, I already tried 3 USB to RS converters with 3.3 V logic, hercules_3-2-8 and putty as SW, with multiple setting, mostly 115200, 8 data bits, no handshake, no parity. Second problem the HDMI do not show useful data either, at least for me there was nothing I can understand as problem. I have 2 orange Pi lite available, so it is probably not a board problem, I tried 2 SD cards and multiple images (desktop legacy kernel 3.4.y and mainline kernel 4.14.y …

As soon as I installed the latest version of the Wheezy I have found that there is some problem with an USB. When I start my Orange PI I can see that USB devices are power supplied from the bus only first a few seconds (when the bootloader is active I guess) and then being switched off. When I plug an USB device and supply it externally then it seems to be working well. My question is: how to switch on power supply of the USB port on my Orange PI? I have read a number of linux forums and found nothing. Very promising seems a command echo on > /sys/bus/usb/devices/usb1/power/level or similar but unfortunately it has no effect. Any hint, guys? Thanks a lot. Radek

Hi ALL, i've problem booting Armbian from SD. Tried to do workaround: 1. boot linaro from SD 2. put tar Armbian Jessie archive to /armbian folder 3. bind /dev, /sys, /proc 4. chroot in armbian folder 5. changed nand1 and nand2 to the nanda and nandb in script 6. started nand-sata-install.sh 7. it installed system on nand. Process finished smoothly. unchrooted. Powered CT off. After power it on have a green LED lighting. CT not booting. Gents, please any ideas? What i missed in procedure.

Seems when I upgrade my pcDuino3 Nano (pcDuino3b to be specific) from the Mainline server 4.7.3 using apt-get to the newest of everything, wifi is no longer seen. I have tried following the kernel upgrade guide as listed here: https://www.armbian.com/pcduino3nano/, but that doesn't seem to solve it. The device isn't even seen anymore. I did at one point get an error in dimes about ‘/lib/firmware/rtlwifi/rtl8188eufw.bin' being missing, which was odd because i don't think thats wifi, but replacing that with one i found on the rpi boards didnt help either. Ive been working on this issue for hours. Everything seems to work great as long as i don't upgrade, but I don't reall…

Hi all, I'm new here and somewhat new to "modern Linux"..I'm more a BSD Guy... I'm using, administering and programming on unices since approx 1992, using FreeBSD (mostly) at home, my wife has a Laptop using Mint installed by me, but I haven't put much effort into my Linux experiences since systemd came up... Ok, approx 2 years before I've got a bunch of more or less unusual embedded HW..Beaglebone, Olinuxino with an A10, some Intel based thingy and something from AnalogDevices if I remember correctly. All of them are more or less old. Now I want to build a kind of a home automation appliance that is reading out data f…

Help please! I have a bp2 which was bought almost a year ago, and use Armbian_5.14_Bananapi_Debian_jessie_3.4.112.raw as the image for couple of months. Today, I'm try to upgrade to the Armbian_5.14_Bananapi_Ubuntu_xenial_4.6.2.raw image, but the pi can't boot at all. What I do to prepare the sdcard with the following procedure: 1. remote the old partitation, and create a new fat32 partitation 2. dd bs=1M if=Armbian_5.14_Bananapi_Ubuntu_xenial_4.6.2.raw of=/dev/sdc; and sync 3. mark the written partitation as bootable with fdisk ps: I'm using fish shell, and the syntax for the dd command is valid So, what's wrong with my steps? How can I troubleshoot? …

Hello everybody. AFAIK Banana PI M1+ share the same costumed Armbian OS with Banana Pro. The Armbian can run pretty well without any changes on my Banana Pro. The problem is, with the same OS image, the on-board WiFi is not working and i can't remember what im doing (what i remember is I do something inside /boot directory), then the WiFi is detected and working properly on my Banana Pi M1+. My simple question is What is the right way to configure Armbian for Banana Pi M1+ after installation? I assume all the default configuration is for Banana Pro and we need some tweak for Banana Pi M1+ especially to enable on-board WiFi and to use GPIO properly.

Hi, I just got a NanoPi Neo Plus2 for which I must prepare an image for our software. Basically I must have a working Ethernet-over-USB, Wifi and NIC. I started with your current Debian image compiled with uses Armbian v8.75 and Linux kernel v4.19.20. In this image Wifi works, but loading the g_ether module does not seem to work. I assume I need to patch the kernel to make this happen, which means I need to build my own images. So I created a Virtualbox environment as described in the documentation, and compiled an image with all the defaults (apart from a date-tag I add to the kernel name for identification). I installed the image to the eMMC and b…

Been trying to use a DS18B20 with the Lamobo R1 and the last ArmBian, without success. As I have already an RTC in the first pins, connected it as follows: PIN 16=GPI04 / DATA PIN 17=3.3V PIN 20=GND I also added the required resistor between 3.3V and GPI04. Add to /etc/modules w1_sunxi w1_gpio w1_therm Added to my fex file: [w1_para] w1_used = 1 gpio = 16 Modified my dts: pinctrl@01c20800 { .... my_w1_pin@0 { allwinner,pins = "PH16"; allwinner,function = "gpio_in"; allwinner,drive = <0x0>; …

Hello. I have my cubietruck (cubieboard 3) configured to boot from sd card, and other files stored on hdd (sata). Few weeks ago (~15.06.2017) I updated armbian by "apt-get dist-upgrade". It worked well until I switch power off. Now it can't boot from sd card. If I remove it - boot from nand is ok. Whet sd card installed - no activity on display, just blinkin LAN port. If I boot from nand, I cat mount both SD and HDD and explore filesystem. But I can't find any logs, updated since 17.06 (time then I switch it off). My guess problem is new kernel, from 4.11.4 to 4.11.5. Please help me fix this, I can take files and content from SD and HDD, but I don…

Hello, I installed ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.14-sunxi on H3 OpiZeroPlus2 board and temperature is 60C (just after boot, nothing is running, CPU 0.5%) Is it normal? P.S. I saw overheating problem on H2+ OPi boards, but no idea if H3 also suffers from this.

Hi, I'm using the very latest armbian build fpr orangepi+, and i'm trying to nat the network from a wireless interface to another wireless interface. My own LAN works, dns server works too, so i can connect to the orangepi+ but i can't make nat working. Is there some known issue about it, or a custom tutorial for nat with this build? thanks for help

Hi, I have serious problems with the 5.25 images of armbian on a cubietruck. After a fresh install and apt-get update apt-get upgrade I get errors with : dpkg: error processing archive /var/cache/apt/archives/linux-libc-dev_4.4.0-78.99_armhf.deb (--unpack) This is for the Armbian_5.25_Cubietruck_Ubuntu_xenial_next_4.9.7 image, with other images this concerns a different package. Only Armbian_5.25_Cubietruck_Ubuntu_xenial_default_3.4.113 works. After this error, the filesystem seems to be defect and is remounted ro. On another try, I removed the rmount ro on error option from the fstab and the /var/lib/dpkg directory was corrupted. …

Hello, I’m from Russia, I don’t speak English well, I write a translator through Google, I hope you will understand me. My Orange Pi One Plus H6 installed different Armbian image 5.3.9 the system works well, but there is no sound via HDMI, in the pulseaudio tab of the configuration menu it says "there are no cards available for configuration". Did I understand correctly that the H6 processor does not support the audio codec, so there is no sound, or am I doing something wrong? Thanks for the answer.

Well a little info, I've been using my orangepi one with an SDR dongle to track airplanes with flightradar24 for the last few months. My intentions were to use a POE adapter and run the board outside near the antenna at one point. I have now received the final parts and went to move it today. It has been running flawlessly for a month with my POE adapter off of a switch near my PC in my shop. I now plan on connecting it to the main switch on my LAN. So previously my setup was: Router -> switch -> long ethernet to shop -> swtich -> orangepione now I want to run it: Router -> switch -> long ethernet to outside -> orangepione But for some reason…

My orange PI PC was working flawlessy but now it wont boot and via serial I can get this: U-Boot SPL 2016.09-armbian (Oct 23 2016 - 17:08:22) DRAM: 0 MiB ### ERROR ### Please RESET the board ### Then it stops there. What can I do?

Hi Guys, After a long time after the release Linux kernel 4.x I want use the I2S on Lime2 (Armbian Stretch kernel 4.14.14), but I2S interface did not work. I was add activation of overlays i2s0 and i2s1 into/boot/armbianEnv.txt root@lime2:~# cat /boot/armbianEnv.txt verbosity=1 logo=disabled console=both disp_mode=1920x1080p60 overlay_prefix=sun7i-a20 rootdev=UUID=dcf7af80-8026-4e99-870f-f0d35f926063 rootfstype=ext4 overlays=i2s0 i2s1 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u After reboot I can't see I2S interfaces... root@lime2:~# aplay -l aplay: device_list:270: no soundcards found... root@lime2:~# lsmod | grep snd snd_soc_core 118…

Hi there! I just downloaded the available image for the NanoPi Neo root@nanopineo:~# uname -a Linux nanopineo 3.4.112-sun8i #24 SMP PREEMPT Thu Aug 4 20:56:33 CEST 2016 armv7l armv7l armv7l GNU/Linux Audio output is only supported for HDMI (but there is no HDMI connector on the PCB). Analog output and SPDIF are not available in the device list. root@nanopineo:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: sndhdmi [sndhdmi], device 0: SUNXI-HDMIAUDIO sndhdmi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 root@nanopineo:~# It is mentioned that also analog should work, but it is not listed as device as you can see above. root@nanopineo:~# d…

Greetings to all, Preamble: Thanks to all that have worked to make the Armbian project what it is today. It is greatly appreciated! I have done numerous hours of reading and searching (due diligence). I know I could run a benchmarks and all but that means even more delay reaching the objective. Some brief guidance from those who have gone before would save a lot of time and would be greatly appreciated. Looking at the datasheets wasn't real helpful in guesstimating optimum performance configuration - especially since there are so many other factors that have an impact. Background: My objective is to achieve a reliable, long lif…

wget https://cdn.kernel.org/pub/linux/kernel/v4.x/linux-4.6.6.tar.xz tar -xpJf linux-4.6.6.tar.xz ln -s linux-4.6.6 linux make oldconfig make menuconfig make-kpkg clean CONCURENCY_LEVEL=3 fakeroot make-kpkg --initrd --revision=14082016.01 kernel_image kernel_headers But USB do not work! I do not found CONFIG_AXP20X_POWER in new config. After manual add its gone! How to solve this ?????

I had a NanoPi NEO2 working well with ARMBIAN 5.34.171121. After apt-get upgrade, ARMBIAN has been changed to ARMBIAN 5.37.171208 with below firmware update: Get:1 http://beta.armbian.com xenial/main arm64 linux-dtb-next-sunxi64 arm64 5.37.171208 [25.0 kB] Get:2 http://beta.armbian.com xenial/main arm64 linux-image-next-sunxi64 arm64 5.37.171208 [14.7 MB] Get:3 http://beta.armbian.com xenial/main arm64 linux-u-boot-nanopineo2-next arm64 5.37.171208 [222 kB] Get:4 http://beta.armbian.com xenial/main arm64 linux-xenial-root-next-nanopineo2 arm64 5.37.171208 [318 kB] Then the Ethernet port is no longer working. Kernel message shows MDIO register f…

Hello to all, I installed Armbian ( legacy kernel ) on my OPI plus 2 H3 but all usb ports not work, only micro usb Otg. I can t use mouse or keyboard someone help me please?

Hello there! Its nice to meet everyone and thank you so much for having me! I have this great project i'm working on involving 30 orange pi zeros. You see SD cards are expensive when you need to buy 30 of them so I have been trying for about a month now to make armbian work without the SD card. The idea is to boot into the os get a few things running and then remove the card and boot another pi. I have tried creating a ramfs mount and copying/mounting (what I believe are) all the requirements and then using chroot. But that doesnt work at all. I'm imagining that outside of chroot services are still running and once they cant write to some file…

I have tested Trusty 5.04 on my Orange Pi PC. It looks very good but perfomance is low because of slow read/write Process from SD Card; especially Browsing.. Is there an easy way (Noobish) to move the Filesystem to an externel Harddisk (booting from SD Card,working with HD)? Regards

Hi, I would like to configure my nanopi Air as an AP and facing some issues. I have edit my /etc/network/interfaces as follow to use hostapd # interfaces(5) file used by ifup(8) and ifdown(8) auto lo iface lo inet loopback auto wlan0 iface wlan0 inet static hostapd /etc/hostapd.conf address 192.168.1.1 netmask 255.255.255.0 and I have linked the the hostapd.config config file in the /init.d/hostapd. my hostapd.config is as below ssid=AERS interface=wlan0 hw_mode=g channel=5 driver=nl80211 logger_syslog=0 logger_syslog_level=0 wmm_enabled=1 wpa=2 preamble=1 wpa_passphrase=aerstest wpa_key_mgmt=WPA-PSK wpa_pair…