Allwinner sunxi

I used armbianmonitor -r on my OPi Zero just like I did previously on OPi One. On OPi One everything is working fine. On my zero it doesn't display all the information for CPU. It shows: CPU total: undefined% (Sys: undefined%, User: undefined%, I/O wait: undefined%, Nice: undefined%) CPU frequency: 1.008GHz DRAM frequency: Not available Governor: ondemand Active CPU cores: 4 Vcore: undefined If I run armbianmonitor -m it shows these data I checked Allwinner_H3_Extended.conf and I noticed that it reads files from /tmp (/tmp/cpustat, /tmp/disktemp, e.t.c) On my OPi One I see these files On OPi Zero there is no rpim…

Hi Linux Admins, I have a wrong device in the /dev direcrory and can't delete it. Here is what I get when I do a: ls -la /dev/ttyUSB* pi@armbian_test: ls -la /dev/ttyUSB* crw-rw---- 1 root dialout 188, 0 Feb 15 20:47 /dev/ttyUSB0 -rw-r--r-- 1 root root 1 Feb 15 20:48 /dev/ttyUSB1 You see that the device ttyUSB1 is not character device and has no major device number assigned. Also the device belongs not to the dialout group. The causing USB_2_Serial Stick is disconnected and the device entry is still there. Trying to remove this devis is also not working. pi@armbian_test: sudo rm /dev/ttyUSB1 …

I have compiled u-boot-sunxi-with-spl.bin and and write to sdcard UART show Can anyone please help make ethernet work on u-boot so i cant pxe boot? Ty

Hi, I've just wrote today's latest image for my Orange Pi PC: Armbian_21.02.1_Orangepipc_focal_current_5.10.12_desktop At first boot, I am asked to make my user and everything is fine and I end up in the XFCE desktop. All works fine. Then, I reboot the system. I see it booting and when X is starting, the screen goes blank (all black). If I do Ctrl+Alt+F1, I can log in in text mode, but X shows nothing. Thank you for your hard work on Armbian! -Alexandre

Hello, I have problem that wireless interface only reachable when ethernet cable plugged to my orange pi zero. I use nmtui, to setup my WiFi connection. All connects fine and works. But when I disconnect ethernet cable, I lost also WiFi connection. I see this post: https://forum.armbian.com/topic/4098-orange-pi-zero-wifi-issues-when-disconnect-ethernet-cable/ But even after rebooting without ethernet cable, WiFi connnection doesn't work. Then in a new clean image, I try to run nmtui without connecting ethernet cable. WiFi connects without any errors, but doesn't work. Please, help! Spoiler This is my ifconfig -a, when …

Hello, I try to communicate on UART3 (pin 11/13) just TTL, but cannot see any data on the lines. After first attempt i added overlays=uart3 to /boot/armbianEnv.txt and rebooted the system. oot@orangepioneplus:~# cat /boot/armbianEnv.txt verbosity=1 bootlogo=false console=both disp_mode=1920x1080p60 overlay_prefix=sun50i-h6 rootdev=UUID=d7bd3629-b17f-4c85-9031-909157a0ce7e rootfstype=ext4 overlays=uart3 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u Then i also executed update-initramfs -u and rebooted the board. None of these are helped I wonder what i am doing wrong? I see the following in the logs: root…

Hi, i would like to read continously from Orangepi zero SPI. I download the latest kernel from https://www.armbian.com/orange-pi-zero/. Now i need to enable the SPI. I tried with changing my /boot/armbianEnv.txt file here i'm attaching it. Then i reboot and loged then i can see spidev0.0. But i want to use SPI1. How to enable SPI 1. armbianEnv.txt

Hi Armbians In the last years I had the pleasure to have more then 30 Cubietruck boards in my hands to work with. Condition of the boards ranged from "new and still sealed" to "working but has been running for some months 24/7 alraedy". In this time, I learned a lot about this hardware and I learned that none of them seems to be 100% like any other of them. While one board crushes immediately when the power input goes under 5V for some secounds, another board in the same condition, same CT version and production date seems not to care about this and keeps working. One of the most important points for stability is the network plug used. So what netwo…

Greetings from USA, my name is Freddy Love and i'm new to Armbian and this forum. Currently i'm using a Lime2 no internal storage with Bullseye CLI on the SD. My pau06 works great, but want to use for small server and would obvi prefer to be hardwired in. Any help would be much appreciated. I'm still going thru everything I can read. My email is freddylovesart@protonmail.com and @freddylove@fosstodon.org // thx in advance. Sincerely, -fl

Hi, trying to start my Banana Pi Pro Board with the latest Armbian buster image (Armbian_21.02.1_Bananapipro_buster_current_5.10.12.img.xz) without success. There is initial output on the screen until there is the message "Starting kernel ...", the after a few seconds the monitor loses its signal and nothing seems to happen any more see: https://c.1und1.de/@520257322610590089/1IBkHiwHQX6jYxLPdlkTZQ Reading through the forum I guessed it could have to do with an issue of automatic discovery of the correct DTB, so I edited the armbianEnv.txt file and added the following line to it: fdtfile=sun7i-a20-bananapro.dtb But still the sam…

Hi, I Would like to connect orangepi PC to 1280x1024 dvi monitor, as I used to with few years old armbian before. Tried h3disp but it reports that board/kernel is not supported. Is there some new method for that? Also it looks like armbianmonitor can't upload system info anymore.

I'm running my Orange Pi Zero headless on Armbian Buster 20.11.6 Last check uptime was 6 days, but now I find its rebooted and I think this is due to unattended security packe upgrades. The package is installed unattended-upgrades/stable,now 1.11.2 all [installed] automatic installation of security upgrades Looking in /etc/apt/apt.conf.d 01autoremove 20auto-upgrades 70debconf 01autoremove-kernels 50apt-file.conf 71-armbian-no-recommends 02-armbian-compress-indexes 50command-not-found 81-armbian-no-languages 02-armbian-periodic 50unattended-upgrades Is…

Hello. From moment when i flashed armbian to SD card and boot it up on Banana Pi M1, random reboots started to show. Ya'll should know that i'm hosting Plex and Tautulli on that. It's pretty much handling these servers without big problems but i'm constantly getting these random reboots. Well, i looked into /var/log/syslog to see what is happening. It looks like before every booting session there's cron job couple of hours before reboot. Maybe that's the reason? I can post whole syslog here from jan 5 till feb 2.

Hi, 2 weeks ago I upgraded my Cubietruck to newest Armbian version: root@cubietruck04:/var/log# uname -a Linux cubietruck04 5.10.4-sunxi #20.11.6 SMP Sun Jan 3 21:28:45 CET 2021 armv7l GNU/Linux root@cubietruck04:/var/log# lsb_release -a No LSB modules are available. Distributor ID: Debian Description: Debian GNU/Linux 10 (buster) Release: 10 Codename: buster Since that upgrade the Cubie is crashing often compared to the last years ( every ~3 days), in the last 3 years I have never observed that. Please help me to find out the issue. From kern.log I see 2 different crash reasons: Jan 2…

I am building kernel 5.10.4 sources on NanoPi Neo 2 with Armbian 20.11.10 Focal and get following error: nanopineo2:~:% cd /usr/src/linux-headers-5.10.4-sunxi64 nanopineo2:linux-headers-5.10.4-sunxi64:% sudo make headers_check nanopineo2:linux-headers-5.10.4-sunxi64:% sudo make scripts nanopineo2:linux-headers-5.10.4-sunxi64:% sudo make prepare scripts/Makefile.build:414: warning: overriding recipe for target 'modules.order' Makefile:1407: warning: ignoring old recipe for target 'modules.order' make[1]: *** No rule to make target 'arch/arm64/kernel/vdso/vdso.lds', needed by 'arch/arm64/kernel/vdso/vdso.so.dbg'. Stop. make: *** [arch/arm64/Makefile:182: vdso…

Hello, After looking on the forum and on the internet I am turning to you. Here is my problem: armbian is currently running on an SD card and I would like to put it on the eMMC memory of my orange Pi 3 (8gb). When I run the sudo nand-sata-install script it offers me to install eMMc on my memory but tells me that the partition is too small. 8go seems largely sufficient to install armbian. You should know that this orange Pi already contains linux firmware in its internal memory. I figured this was due to the fact that maybe this version of armbian didn't support emmc memory, so I tried with the focal version, the buster version and the bionic version…

Latest kernel installed, compare attached dmesg-s. It starts working again after `reboot` invoked from serial console. dmesg-ok.log dmesg-watchdog-5.10.log

I am trying to install Tensorflow on my Orange Pi One. Everything seems okay on install, but pip says ERROR: Could not find a version that satisfies the requirement tensorflow ERROR: No matching distribution found for tensorflow My guess is that the OS is a 32bit version and that Tensorflow runs on 64bit ones only. However, I can't find any source of checking whether the Armbian version I have is 32bit or 64bit.

I'm running a fresh installation of Armbian 20.11 Focal with Linux 5.8.16-sunxi on NanoPi Neo board with Allwinner H3. root@nanopineo:~# uname -a Linux nanopineo 5.8.16-sunxi #20.08.14 SMP Tue Oct 20 22:15:32 CEST 2020 armv7l armv7l armv7l GNU/Linux The problem is that MAC address changes on every boot. This is very problematic for systems where an IP is assigned by DHCP based on MAC address table. I have two important questions: 1) Why MAC address is not generated based on processor unique ID? This seems to be the most sensible solution. 2) What part of code/startup script is assigning the random MAC address? Unfortunatelly I was not a…

Hello, Is there anyone that has problem with USB keyboard on armbian 20.11.9 buster. I have tried both 20.11.6 and 20.11.9 buster nut the keyboard can't be recognized in armbian. (caplock, numlock LED don't work as well) I tried 4 USB ports on the port but doesn't work. The keyboard is working fine with my Windows PC. Thanks

Hi guys orangepi-one and i'm trying to install the Super Nintendo Classic Controller wich is i2c bus /---------\ | | | 1-2-3 | | 4-5-6 | | _____ | \_/ \_/ ``` | Controller Pin | Function | Pi Pin | |---------------:|---------------|-----------| | 1 | I2C data | 3 (SDA) | | 2 | device detect | - | | 3 | +3.3V | 1 (+3.3V) | | 4 | GND | 6 (GND) | | 5 | not connected | - | | 6 | I2C clock | 5 (SCL) | i have wired the controller to the orangepi bus port 0 and port 2 i found a driver fo…

Just flashed Armbian 20.11.9 for NanoPi Neo 2 with kernel 5.10.4. I have run armbian-config to install kernel 5.10.4 source, but there is no any option for 5.10.x kernel sources, I see only options for 5.8.x and 5.9.x.

Hello, I try to communicate via SPI, if i try receive data over SPI on MISO pin I got message without last bit so I should receive 0x23 and i got 0x22. SPI is set on MODE 3. It has same behaviour on PI PC and PC2. If i try on RPi it works fine. Do you have anybody some advice ? Regards Jan

Hello, I try to communicate via SPI, if i try receive data over SPI on MISO pin I got message without last bit so I should receive 0x23 and i got 0x22. SPI is set on MODE 3. It has same behaviour on PI PC and PC2. If i try on RPi it works fine. Do you have anybody some advice ? Regards Jan

Hello everyone! I am designing a PCB and I need to know if there is a possibility to swap SPI0_CLK and SPI0_CS by changing this line from: pins = "PC0", "PC1", "PC2", "PC3"; to pins = "PC0", "PC1", "PC3", "PC2"; Currently I don't have a board to check it myself. Any ideas if this would even work? Thanks!

Hey, I am using the Image from the Armbian Download site: Armbian_20.11.6_Bananapim2zero_bullseye_current_5.10.4 and I am trying to get SPI to work, enabled it using armbian-config and through editing the /boot/armbianEnv.txt verbosity=1 bootlogo=false console=both disp_mode=1920x1080p60 overlay_prefix=sun8i-h3 rootdev=UUID=034edbda-9395-4820-87a1-f3a83bad8a58 rootfstype=ext4 overlays=spi-spidev usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u But after a reboot it does not show in /dev/ (what seems odd, i2c-0 shows in /dev/ even though it is not enabled in the armbianEnv.txt) As far as I understand it, the …

I had got a OrangePI One Plus (H6) on a few day ago. I had a problem with HDMI to VGA Converter that it do not work with my OrangePI One Plus. I guess it maybe about the Power of that HDMI on OrangePI One Plus was not enough for HDMI to VGA Converter's operation. Then I fix it by replace regular HDMI to VGA to be HDMI to VGA with 5V external port. And Yeah, it's work fine!!! but I had OrangePI One (H3), OrangePI PC2(H5) and OrangePI Prime(A64) too which All of them had no problem with HDMI to VGA Converter. I feel wonder with this problem on OrangePI One Plus.

Hi I am trying to set up auto-login with enable desktop, using armbian-config as user root, and getting 'killed' once I select which under-priviledged user to enable. (There's two to choose from, and both behave the same with the same error reult). I couldn't find a known issue, please help! OPi Zero LTS 512MB / Armbian from armbian.com Sam

Hello, first post here, so sorry if did not provide enough information. I need to change spi buffer length to 8192. So far tried: 1) modprobe spidev bufsiz=8192 creating the file /etc/modprobe.d/spidev.conf and adding to it the line "options spidev bufsiz=8192" When I do "cat /sys/module/spidev/parameters/bufsiz", it gives me "4096". 2) Add to /boot/cmdline.txt: spidev.bufsiz=8192 When I do "cat /sys/module/spidev/parameters/bufsiz", it gives me "4096". 3) cd /sys/module/spidev/parameters chmod 666 bufsiz echo 65536 > bufsiz did nothing. 4) /boot/armbianEnv.txt added options spidev …

Hi, I have a Bananapi M1 running long Time with Debian Jessie. Now I installed Armbian Buster and always when I activate GPIO Pins my Network is gone on the integrated Card. Also GPIO is not working because of the Network Card. I tried to deactivate the Network Card and use an external WirelessLAN Card but the internal Card is still blocking my GPIO's. On Jessie and Wheezy before that was working perfect. Any advise? BR Peter

Hello. During the Italian pandemic lockdown I am building a mini cluster with some boards that I have found in my house. I have three OrangePi and one Nanopi Fire3. I assembled them in a box and I connected them via ethernet. I connected the monitor on a OrangePi One plus. The keyboard and mouse are on a blouetooth usb key. I would like to have all Armbian (for the reasons that you all know!). I installed all SD with Armbian Images. Every SBC has the text file with fixed ip parameters. All the network files (etc/network/interface) are well written and in the local network all Armbians are pinging each other ones. I reach them via SSH and they talk with the one that has th…

i just installed Armbian_20.11.6_Orangepione_buster_current_5.10.4.img the software is trying to install a driver and is requesting the linux headers, i tried to install the linux headers but is says E: unable to locate package linux-headers-5.10.4 then i switched to the nightly upgrades in the armbian-config and now is on 5.10.7 also tried to install iand i keep getting the same msj E: unable to locate package linux-headers-5.10.7 any clues with this problem ? thanks http://ix.io/2MjH

Hi friends, i'm new here, i found an old Orange Pi PC (V1.2) in my treasure-box and try to find a bootable image in the Orange Pi sources. But any image i tried was faulty, one time the system is starting, but not booting completely ore i have a red LED (don't boot). I tried it with a 8GB und a 32GB card. Pls, can you tell me, where i can download a running image and do you know, if a 32GB-Card ist ok? I write the img with "BelanaEtcher" on the SD-Card, same as i write it on a SD-Card für a Rasp-Pi. Thank you for any helpful answer. Stefan

Hi Armbians I am running mulitiple TOR network relays on Cubietruck boards (Cubieboard 3) in different Datacenters with synchronous 100 MBit/s internet connection each board (by ethernet plug) for 1- 1,5 years now. At the beginning each board could handle 25 MBit/s incomming and outgoing traffic the same time easy and 24/7. The boards are running the latest Armbian build with kernel headers installed and full firmware package. But now, as you can see here, my Cubietrucks are getting slower after time, with the network traffic they can handle via eth0: https://metrics.torproject.org/rs.html#details/EC9C4CDB403204731122C9D3FA44DFAE6…

Hi all, I am hoping there is a straight forward solution to this; I've read this thread on turning on and off the usb OTG using GPIO commands: The concept is really clever and I was hoping to use it as part of my Octoprint 3D printing setup so that I can turn off printer when not in use. The only catch is that the method requires modifying the ./bin/orangepione.bin file which isn't present on my version of Armbian (Buster). TL;DR according to the post I need to 1. convert ./bin/orangepione.bin to FEX, 2. edit the file by adding "usb_drv_vbus_gpio = port:PL02<1><0><default><0>", 3. convert …

Hello, I was looking for Kali on BPi and tried the "Kali Linux BananaPi offensive-securityDOTcom-2020.04"-image without success. Unfortunately the image does not boot and no support from there (Domain-contact nor forum[...][...]). Some message about "mount: mounting /dev/mmcblk0p1 on /root failed: No such device", even if kernel was started from this 'No such device"'-SD-card. So Igor wrote me about katoolin which I tested on BPi with Armbian 20.11.3 Busterarmbian. For anyone who is interested here is my way: install "Armbian 20.11.3 Buster \l" install "katoolin see…

Hi I was trying to setup an mini arcade to my room. I was using retrorangpi 4.2 full desktop (Debian Jessie) on my orangepipc. When it was booting, the screen is only red and the info showing in my monitor is DVI-HDMI 720p 60 but I am not using a HDMI TO DVI converter. I try to configure my display on armbian-config and I choose HDMI not DVI but the result is the same after rebooting. Can someone tell me how to fix this?

Hi there, 2 days ago I did apt update + apt upgrade on my OPi3, everything fine. Yesterday I did a system reboot (as suggested "kernel changed"), then Eth port went dead. No even ARP works (ARPING). Have tried: - ifconfig shows correct values, - ethtool shows 1Gbps FDX connection, also same on router (OpenWRT TL-WR1043ND w 18.06 software), - changed eth cable, - on other OPi connected to same switch / router (also went dead) depowering device helped, but not on OPi3, - ARP shows MAC/IP not resolved, - WiFi (configured as AP) looks working. - also changed port on router and did power cycle device, nothing helps. - on r…

Linux cubietruck 5.10.4-sunxi #20.11.6 SMP Sun Jan 3 21:28:45 CET 2021 armv7l GNU/Linux ------------[ cut here ]------------ [ 1.304783] WARNING: CPU: 0 PID: 1 at arch/arm/mm/ioremap.c:287 __arm_ioremap_pfn_caller+0x13f/0x14c [ 1.304791] Modules linked in: [ 1.304812] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.10.4-sunxi #20.11.6 [ 1.304818] Hardware name: Allwinner sun7i (A20) Family [ 1.304852] [<c010c9ed>] (unwind_backtrace) from [<c0109501>] (show_stack+0x11/0x14) [ 1.304873] [<c0109501>] (show_stack) from [<c0966dcb>] (dump_stack+0x77/0x84) [ 1.304892] [<c0966dcb>] (dump_stack) from [<c011ae99&g…

I'm running Armbian Bionic on OPizero. I have a problem using arecord on the mic input. Audio codecs have been enabled but when I run following command to record I get a pcm read error arecord -D plughw:0,0 -d5 -f cd test.wav Recording WAVE 'test.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo arecord: pcm_read:2103: read error: Input/output error There is no recording and file is just 44 bytes. pi@orangepizero:~$ ls -l test.wav -rw-r--r-- 1 pi pi 44 Jan 6 20:44 test.wav The output from this command never finishes after 3 seconds and I have to use ctrl+c to breakout: arecord -vvvv -d 3 /dev/nul…

Remark: on my Orange Pi PC and Orange Pi Plus 2e - everything is OK. Problem occurred on Orange Pi Plus 2 and Orange Pi Zero After upgrading to: [root@PKTEST ~]# uname -a Linux PKTEST 5.10.4-sunxi #20.11.6 SMP Sun Jan 3 21:28:45 CET 2021 armv7l GNU/Linux My "headless" Orange Pi Plus 2 "disappeared from network. I switch it off and connected via serial. I was able to login. Device runs successfully, it is assigning IP to network interface (static assignment) but... there is no connectivity at all (both egress and ingress). [root@PKTEST ~]# ifconfig enx0281cbcd0fcf: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 …

I have updated the armbian kernel from version 20.11.3 to version 20.11.6 and eth0 only works by forcing the switch to 100FD. If I leave it on automatic, the port negotiates at 1000FD but loses most packets. Any suggestion?

Hi Yesterday I've upgraded armbian kernel from 20.11.3 to 20.11.6 version in the available updates with apt update. Once PiPC restarted no wifi connection was found. The wifi dongle is a TP-LINK TL-WN725N and is found with lsusb: Bus 004 Device 002: ID 0bda:8179 Realtek Semiconductor Corp. RTL8188EUS 802.11n Wireless Network Adapter It was working with previous kernels but with 20.11.6 kernel is not listed in ifconfig so I've rolled back to 20.11.3 kernel Any hints or solucions ?? Thanks

hello there, and Happy New Year I have OPI PC PLUS, and it was unused for a while , then I did update upgrade it and since this time my old python scripts doesn't work at all it looks like scripts turn on OK but nothen happend I use OrangePi.GPIO 0.6.3

I'm trying to disable IPv6 on my NanoPi Neo2. Initially I used the option in armbian-config -> Network -> IPv6 (toggle). I can confirm that IPv6 is disabled by running 'ip a' and no longer seeing any IPv6 addresses. And I can also confirm that the following config is changed in /etc/sysctl.conf: net.ipv6.conf.all.disable_ipv6 = 1 net.ipv6.conf.default.disable_ipv6 = 1 net.ipv6.conf.lo.disable_ipv6 = 1 However after a reboot I see the IPv6 addresses back. I found a guide (itsfoss) that suggest the same changes to sysctl.conf and if the changes do not persist ander a startup I should make edit /etc/rc.local : #!/bin/bas…

After about 10-20 hours of normal work the IP address on USB wifi adapter disappears. Ethernet adapter connected to the same router works well at the same time. System diagnosis information is collected when IP address is missing. After re-plug USB-adapter into the same USB port or reboot, the IP address appears back. Board: Orange PI PC, WIFI: EDUP dual-band on 8811CU chip, built-in drivers Image: 20.11.3 focal Router: Keenetic Ultra Previously I used built-in wifi of Orange PI+ and I didn't have similar problem. Is the problem specific to the WIFI adapter?

HI to all, excuse me but this is my first msg. I have a OPI3 board and I try different OS (Arabian, Ubuntu, Debian) all in different release but I do not have wifi and lan. for wifi I have already try with copy firmware file but is is the same for lan I have in dmesg eth0. UP and DOWN. In my experience I have found only Ubuntu Xenial 4.9.118 on the Orange.org web site with wifi OK. can you help me? Thanks

Hi all, I trying many days set up temperature sensor work, but no luck ( Orange PI PC Armbian 20.11.3 Focal with Linux 5.9.14-sunxi try many pins, 3 and 5 V , but same result, no sensor read. No any resistor, 1 sensor armbianenv: overlays=w1-gpio usbhost0 param_w1_pin=PD14 param_w1_pin_int_pullup=1 output: root@orangepipc:~# gpio readall +------+-----+----------+------+---+OrangePiH3+---+------+----------+-----+------+ | GPIO | wPi | Name | Mode | V | Physical | V | Mode | Name | wPi | GPIO | +------+-----+----------+------+---+----++----+---+------+----------+-----+------+ | | | 3.3V | | | 1 …

I have just downloaded and installed a fresh Buster Image (Armbian_20.11.3_Orangepi3_buster_current_5.9.14.img). After configuring the root password and the new armbian user, I have tried to update the system using (apt-get update....) But I noticed that there is no internet connection through the ethernet cabble. The command ethtool eth0 says that the link is detected. When trying to activate the Wired connection using "nmtui", the system says: could not activate connexion: Activation failed: IP configuration could not be reserved (no available address, timeout, etc.) Could you assist me to resolve this problem. Note: 1-Th…

Hello, A newbie here can anyone give me an instruction on how to set Analog Video as Output display in Orangepipc, I am using Armbian Buster with mainline based kernel 5.9.y.

Hi. I've always had problem with the composite output (cutted edges) so i gave a try to the latest release. Unfortunatly the video does not show up at all. Anyone still using the old Opi0?

After updating to 5.9.14 from 5.8.16, framebuffer is broken. No output after booting, hdmi monitor goes to sleep. [ 1.455763] ------------[ cut here ]------------ [ 1.455791] WARNING: CPU: 0 PID: 1 at arch/arm/mm/ioremap.c:287 __arm_ioremap_pfn_caller+0x13f/0x14c [ 1.455796] Modules linked in: [ 1.455810] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.9.14-sunxi #20.11.3 [ 1.455814] Hardware name: Allwinner sun7i (A20) Family [ 1.455846] [<c010cce9>] (unwind_backtrace) from [<c010945d>] (show_stack+0x11/0x14) [ 1.455862] [<c010945d>] (show_stack) from [<c093b0ab>] (dump_stack+0x77/0x84) [ 1.455878] [<c093b0ab>]…

Hello, It's my first message, I'm very proud to be part of your community, Armbian is epic ! I'm trying to add a chinese screen copy to my orangepizero (H2+ cpu). This is my screen: https://www.aliexpress.com/item/32587995145.html (copie of https://www.waveshare.com/3.5inch-rpi-lcd-a.htm) 1) Yesterday i setup my screen on Armbian_5.91_Orangepizero_Debian_buster_next_4.19.59 with success with: nano /boot/armbianEnv.txt : overlays=spi-spidev spi-add-cs1 param_spidev_spi_bus=1 param_spidev_spi_cs=1 nano /etc/modules-load.d/fbtft.conf : fbtft fbtft_device nano /etc/modprobe.d/fbtft.conf : options fbtft_device rota…

Can someone please add support for the onboard microphone to armbian for the Lite2?! It is missing in armbian-config, there is no h6-analog-codec.dtbo in /boot/dtb/allwinner/overlay The microphone is wired up the same way as on the other h6 boards. Thank you very much!

Guys please help me. My orange pi one with Armbian installed and running Pi Hole. The HDMI Output is not working, And when I try to enter this command h3disp [-h/-H] -m [video mode] [-d] [-c [0-2] it say access denied. My point is there's no output this play on my device. I hope someone understand me and help me thank you.

hi guys, i'm using NanoPi neo core using a battery and a volt booster. and I want to control the voltage booster to turn off all peripherals to conserve power and prevent battery drainage. I figured there's a PWR-LED pin connected to GPIOL10, which turns off when the system shut down. is there a way to map another GPIO in the same way so i could know when the system has shut down - so it will be safe to cut power off? thank you so much.

Hello I have a problem with my Xunlong Orange Pi PC Plus, if I put an SD card with Armbian_20.11.3_Orangepipcplus_buster_current_5.9.14 or focal (format with Etcher) it will boot with the MMC is not with the SD card i have an error Trying to boot from MMC1 ... MMC: mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c11000: 1 Loading Environment from FAT... *** Warning - bad CRC, using default environment ... mmc0 is current device Scanning mmc 0:1... Found U-Boot script /boot/boot.scr ... EHCI failed to shut down host controller. Loading Ramdisk to 4969c000, end 49fff9c3 ... OK Loading Device Tree to 4962b000, end 4969bfff ... OK Starting kernel ... and after…

hardware: Orange Pi Zero H2 Kernel: 5.9.14-sunxi Armbian 20.11.3 Buster ethtool version 5.9 get error on cable-test option. full log: http://ix.io/2Icy sudo ethtool --cable-test eth0 netlink error: PHY driver does not support cable testing netlink error: Operation not supported

After recent upgrade of Debian Buster stable on Orange Pi Zero Plus 2 leds entries disappeared from class directory: Could anybody provide some guidance on how to get them back?

I didn't see support specifically for NanoPi NEO-LTS https://www.friendlyarm.com/index.php?route=product/product&product_id=132 Does one of the other images work on this particular board?

I'm not sure if I should pursue this here or if I should open a ticket through Debian Bugs. A recent update now causes mpd to segfault. mpd comes from the Debain armhf repository. I'm not sure how to determine if this is a hardware issue with my board somehow or if there is an interaction with a new kernel or if it's because the package updated the binary or a library. To make sure it wasn't something weird in my configuration I moved the conf file out of the way and re-ran mpd with the same result. If it helps, I can post an strace output of the issue. James

I just updated my armbian kernel, I did it with: apt-cache search linux-generic to find the images and sudo apt-get install name of the image to install, the new kernel is in the /boot folder but if I restart It continues to start with the old one, and if I eliminate the old one it no longer starts. How do I select the new kernel to boot from it? i use orangepi+2e

Hi, I started using pinebook armbian buster when it was beta, it worked. From that beta I upgraded yeysterday and I see no display (LCD) after kernel starts (I only see the boot). The same using a new official image [1] I know there is another places to track this issue [2], but the thing is that in the official image page [1] it says it is fully working and that is not true. There are two options: - changing the status to something beta (like before) so you are less responsible of problems - putting an image that works [1] https://www.armbian.com/pinebook-a64/ [2] https://armbian.atlassian.net/browse/AR-443

I'm on a years old Orange pi zero H2, an often forgotten single purpose print/scan server board. So i want to upgrade to the latest kernel via armbian-config->system->other(switch kernel). Previously its on 4.19. so when i tried to change to current 5.8.16, 5.8.14, 5.8.12 & 5.8.5, i got "No end-user support: unsupported (stretch) userspace!" it has taken me an hours plus just switching kernel, hoping to find the supported ones. though i dont mind unsupported / legacy kernel, i still prefer the latest supported ones. Is any of the kernel on the list supported? if there none on the list, is there a way to add a supported kernel?…

Can someone post the printenv for a NEO PLUS2 because i think i f*** up my device and doesn't boot from SD or USB .... the only i get is the boot menu. Or any ideas to help me to fix this ?

Hi, we are trying to make our Orange PI zero with custom shield working with an MCP2518FD on board with SN65HVD23 tranceiver. We started from the normal kernel already built, but according to this thread we found that it must be activated at compile time. So we downloaded the repo and built the Armbian image with this CAN configuration: CONFIG_CAN=y CONFIG_CAN_RAW=y CONFIG_CAN_BCM=y CONFIG_CAN_GW=y CONFIG_CAN_J1939=y # # CAN Device Drivers # CONFIG_CAN_VCAN=y CONFIG_CAN_VXCAN=y CONFIG_CAN_SLCAN=y CONFIG_CAN_DEV=y CONFIG_CAN_CALC_BITTIMING=y CONFIG_CAN_FLEXCAN=y CONFIG_CAN_GRCAN=y CONFIG_CAN_SUN4I=y CONFIG_CAN_TI_HECC=y CONFIG_CAN_C_CAN=y CO…

Hi, I have a orange pi pc. I tried the ubuntu xenial image (kernel 5.3.5) from the orange pi website and the armbian 5.8 image. I don't get vdpau working. It did not work out of the box in both images. So I tried to install the libvdpau-sunxi: http://www.orangepi.org/orangepibbsen/forum.php?mod=viewthread&tid=878 It compiled. Then I got the error that the cedar_dev dosn't exist. Then I found out that the mainline kernel doesn't have this module. So I tried this: https://github.com/uboborov/sunxi-cedar-mainline But I don't understand what I have to do there. Is there a current armbian image that has a working vdpau or can you…

Hello. Good day. I'm trying to use the SPI on a OragenPI One Plus (Allwinner H6), and, although I have enable it via the /boot/armbianEnv.txt configuration, communication is not working. Here's the armbianEnv.txt armbian@orangepioneplus:~$ cat /boot/armbianEnv.txt verbosity=1 bootlogo=false console=both disp_mode=1920x1080p60 overlay_prefix=sun50i-h6 rootdev=UUID=19c1886e-0b74-45b8-b9f5-5fbd4bdeb5c2 rootfstype=ext4 overlays=spi-spidev param_spidev_spi_bus=0 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u And here's the SPI device listed under /dev armbian@orangepioneplus:~$ ls -la /dev/sp* crw------- 1 root root 153, 0 nov 28 15:…

I'm trying to make a master image to install to some NanoPI Neo boards. I have everything running fine from micro SD card. I used armbian-config to flash from SD to the eMMC and it boot and works. Now I'm looking for a way to flash the eMMC from command line in an automatic fashion, after looking for other threads in the forum I found about command nand-sata-install but it has a GUI and no --help parameter, so I guess it is not the exact program I have to use. I tested using dd command to copy the disk, but since there is this u-boot thing I think it is not just a standard disk copy because it failed (maybe my problem). My final idea is to have a master SD …

During first boot and following first login as root got this error message: New to Armbian? Documentation: https://docs.armbian.com Support: https://forum.armbian.com New root password: ************ Repeat password: ************ Detected timezone: America/Mexico_City (CST, -0600) Generating locales: es_MX.UTF-8 Adding console keyboard layout: mx /usr/bin/ckbcomp: Can not find file "symbols/mx" in any known directory I am not sure that console keyborad layout "mx" exists.

Hi, I need to use the i2c in the u-boot stage. I've added a patch that enables this i2c bus in the device-tree, and when I run this command (just for example): sudo i2cset -y 2 0x1b 0x1 0xf AFTER the boot stage it seem to work. However when I try this command IN THE boot stage, I get: Unknown command 'i2cset' - try 'help'. 1. I guess I'm trying to use 'i2cset' in a too early stage - any idea how to control the i2c in the u-boot stage or how to make 'i2cset' available at the u-boot stage ? 2. Since 'i2cset' doesn't work in the u-boot stage, I don't know if the i2c is enabled at this stage (I know it's enabled after boot) - how can…

Attempting to connect ILI9341 LCD with XPT2046 Touch to NanoPi NEO Core2 and then migrate to NanoPi Duo2. The ILI9341 / XPT2046 peripheral board has shared SPI with a separate slave chip select for the screen and touch controllers. Starting with hardware datasheet for the H3 I see there is lots of support for different chip select implementations. This makes me think I am on good footing from a hardware perspective. What is not clear to me is how the register support for four slave chip selects translates into pin assignments. Reading through spi-sun6i.c., for example, static int sun6i_spi_transfer_one( ... ) uses SUN6I_TFR_CTL_CS_MANUA…

Hi, I'm trying to use hardware acceleration on my OrangePi PC+ (H3) board, and when I try to compile v4l2-request, it complains for undefined constants. These constants are supposed to be declared in /usr/include/linux/videodev2.h, but looks like a very old version of this file is distributed in the latests Armbian images for my board. Some missing headers: V4L2_PIX_FMT_MPEG2_SLICE, V4L2_PIX_FMT_SUNXI_TILED_NV12 Looks like these #define have been introduced more than two years ago in the mainline kernel : https://github.com/torvalds/linux/blame/d5beb3140f91b1c8a3d41b14d729aefa4dcc58bc/include/uapi/linux/videodev2.h#L698 Even more weird: a later …

I noticed that hop lost its cpu bars. I tried to add them but ger error: munmap_chunk(): invalid pointer Anyone else have this problem? Thanks

Good evening, I ran into some problems with sbc-bench on a couple of Allwinner boards Orange Pi Zero, Orange Pi Zero+, Orange Pi One and Nanopi Neo 2 spcifically. The 7 Zip benchmark causes the following error: ./sbc-bench.sh: Zeile 611: 4206 Bus-Zugriffsfehler "${SevenZip}" b >> ${TempLog} Most likely due to a problem with the ZRam: zram: Decompression failed! err=-22 This happens on all boards under Debian and focal with different SD cards and power supplies. The benchmark ran previously on this setups without any issues – unfortunately I don’t know when it stopped working and hence cannot narrow do…

Hi, I've been using Armbian for three years on some work's project and this is the first time I see this issue. Basically I have an image of the operative system and all the programs and scripts already saved in it, so when I have to prepare a new SD card I just use the command "dd" and then I modify some registry stuff specific for the object I'm creating. It has always worked without problem, but now we bought a new batch of SD cards and I'm facing this issue: the dd command goes succesfully and if I mount the partitions after it has finished I can see all my data, but when I boot the system sometimes I get some errors. Here is the last part of the…

I have a raspi hat (rak2245) that has 2 versions: a pi-hat version that has a 40 pin-header on it for raspberry pi's , but also a smaller stamp edition. It uses spi and uart to communicate with the pi. I have it running without issues on my orange pi zero, even though the pinheader is a little too large. And via a breadboard I can access all pins just fine. But since I am making my own PCB anyway, I am interested in using the stamp version. The only difference between the stamp and the pi-hat version (aside from the form-factor and pin-out) is that the pi-hat version has an additional eeprom chip to tell the rapsberry pi about the function of the pins apparently. Now…

On the 20.08.2 Buster release (Kernel 5.8.6) the headphone jack is not currently working. HDMI audio seems to be supported. aplay -L returns only the HDMI audio interface. (sun50i-a64-hdmi) but is not showing the headphone interface (should additionally show sun50i-a64-audio as in other working builds) This is also the case with the current development build (Armbian_20.11.0-trunk.32_Lime-a64_buster_current_5.9.7) A look at the device tree shows “<stdout>: Warning (unit_address_vs_reg): Node /sound/simple-audio-card,dai-link@0 has a unit name, but no reg property” on the first line of the DTS of sun50i-a64-olinuxino, sun50i-a64-olinuxino-e…

I have the same problem like other users here, the 1-wire doesn't run correctly, I added 1-wire to armbianEnv.txt, 1-wire drivers are loaded, but I cannot access the data of DS18B20 attached to PA06. L. ___ ____ _ _____ / _ \| _ \(_) |__ /___ _ __ ___ | | | | |_) | | / // _ \ '__/ _ \ | |_| | __/| | / /| __/ | | (_) | \___/|_| |_| /____\___|_| \___/ Welcome to Armbian 20.08.17 Bionic with Linux 5.8.16-sunxi System load: 26% Up time: 0 min Memory usage: 14% of 491M IP: 192.168.3.163 CPU temp: 45°C Usage of /: 4% of 29G Last …

Hardware: Orange Pi Zero 512MB LTS (several different devices), bench power supply, good SD card - everything working good at all clock speeds from 480MHz upwards (all the way up to 1.4GHz even, with a heatsink). ffmpeg encode, stress-ng etc. are all fine. Specifically, the board is rock solid at 960MHz. What I want to achieve: take the U-boot for OPi Zero, and rebuild with an adjusted config to achieve a faster boot time, by replacing CONFIG_SYS_CLK_FREQ=480000000 with CONFIG_SYS_CLK_FREQ=960000000. (Does anyone know why the standard Armbian build is set to boot at such a low clock speed?) Starting point: I can successfully build U-boot from the A…

Hello I have an allwinner H2 & H3 (PC +) when it does not boot on my LAN. If I want to try to use the LAN port. In / etc / network / interfaces the eth0 interface is not defined. I tried to change the iso but on Windows the iso is not valid. On Linux Linux the files are not -w and try to change but not possible !!! If I want to try to use the UART port and PuTTY it doesn't go with in the prompt. U-Boot 2020.04-armbian (Sep 02 2020 - 10:21:09 +0200) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi PC Plus DRAM: 1 GiB MMC: Device 'mmc@1c11000': seq 1 is in use by 'mmc@1c10000' mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c1…

I will try and remember all the relevant details. Going ~ in reverse chronological order here. Earlier this evening, @lanefuwas helping me in IRC (which I greatly appreciate btw) but he had to go to bed. Next step was getting out the UART he said. So I did that, now I come here to report the results: U-Boot SPL 2020.10-armbian (Oct 18 2020 - 23:16:40 +0200) DRAM:Timeout initialising DRAM resetting ... [...repeats...] Prior to that, we were trying to fix the bootloader and/or firmware. At that time the new kernel (latest stable), initrd, etc. all appeared to be in /boot (we had thought maybe sd card was fried, but apparently not). Pr…

I am operating a headless data acquisition system with Orange Pi Zero Plus2. In the readings I collect among others data from a discrete separate 18B20 sensor and record the H3 CPU temperature. The 18B20 reading comes from the w1 kernel routine, the CPU temp is provided by armbian OS. With the new OS 5.8.16 I see a strange effect: reading .... the external sensor at /sys/bus/w1/devices/<sensID>/temperature and the CPU temperature at /etc/armbianmonitor/datasources/@soctemp it gives the same reading correct to a 1/100 degree. Even when the system runs low power - this cannot be true. I have no idea how these results can be mixed in t…

Hi, I have "orange pi 3" and I want to migrate "Debian Buster" from "SD" card to eMMC. I run this command sudo nand-sata-install And I only get this! see link https://ibb.co/wQz0jx4 As you can see there is no item "Boot from eMMC - system on eMMC" What am I doing wrong? PS - Armbian Buster downloaded from https://www.armbian.com/orange-pi-3/

Hi, I have quiet a problem getting ipsec/strongswan running on my Orange Pi R1. IPSec is configured fine and it connects to my vpn gatway by establishing and ikev2 connection with the help of transform (xfrm) interfaces. After connection everything works fine, but not for long. When I transfer large amounts of data (e.g. iperf3) the whole Orange Pi R1 freezes suddenly. This occours almost immideatly, sometimes i get a couple of seconds a data stream, but mostly it freezes at once. Currently I use even the lates "Linux orangepi-r1 5.9.1-sunxi #20.08.14 SMP Tue Oct 20 23:01:54 CEST 2020 armv7l GNU/Linux" Kernel, and I upgrade…

Hi All, I'm trying to enable SPI2 on Olinuxino LIME2 board following the instruction of Armbian doc, and the README.sun7i... in the /boot/dtb/overlay directory. It seems I have to enable an spi2 device, but the overlay for SPI2 of sun7i is not present. The related section of armbianEnv.txt is the following: overlays=i2c1 spi-spidev uart2 uart3 uart4 uart5 uart6 uart7 param_spidev_spi_bus=2 param_spidev_max_freq=10000000 What I'm doing of wrong? Thanks in advance PaoloC

I'm testing the OrangePi+ and OrangePi+2 for review. I noticed my OPi+ was running a lot cooler than my OPi+2. Reason is difference in kernel. Just tried 5.8.5 on the OPi+ and it also ran as hot as the OPi+2. OPi+ with kernel 4.19.62 vs OPi+/OPi+2 with kernel 5.8.5 No fan idle OPi+ 50C No fan maxed OPi+ Throttle at 75C to 1.3Ghz at 80C to 1.2Ghz doesn't go higher than 80C Fan idle OPi+ 27C Fan maxed OPi+ 54C No fan idle OPi+2 58C No fan maxed OPi+2 Throttle at 80C to 1.3Ghz at 85C lower. Barely reaches 85C / Debian throttle at 75C to 1.3Ghz Fan idle OPi+2 33C Fan maxed OPi+2 60C 2 heatsinks+fan 64C w…

Good morning all I have an OPi Zero H2 with the official expansion card. My goal is to make an Airport module to connect a speaker to it. The installation of Shairport in APT all is ok I can see the sharing on my iPhone. But the problem is that I have no sound when I plug a speaker into the 3.5mm jack port on the expansion card. I have correctly installed the "analog-codecs" and made a reboot. In Alsamixer I put "Line-Out" and "DAC" to the maximum (red). But still no sound ... When in doubt, I did all these operations on Armbian Focal / Buster / Bionic but it didn't change anything. Can you help me please? believe me I have tried everything for 4 da…

An interesting fact (at least from what I can tell), the NanoPi Duo (v1.0 and v 1.1) has no builtin PUDs. Checking http://wiki.friendlyarm.com/wiki/images/8/8a/Schematic_NanoPi_Duo-v1.1.pdf and I see no PUDs on the GPIO schematic. Is this true? Is the Orange Pi Zero the same way?

Hi All, I'm trying to enable SPI2 on a A20 Olinuxino LIME board. I found an old post on this forum regarding LIME2, so I try the same and in armbianEnv.txt I add the lines: overlays=spi2 spi-spidev param_spidev_spi_bus=2 param_spi2_bus_pins=b At reboot, the message: Failed to load '/boot/dtb/overlay/sun7i-a20-spi2.dtbo' I think because the file is not found Only SPI0 is active How can I enable SPI2 ? Thanks in advance PaoloC

hi i try to load bootlog from /boot/mmc on orange pi lite when add bootlogo=true to armbianEnv only armbian logo show. i check u-boot and it send an erro "Unknown command 'bmp' - try 'help'" i check u-boot env and u-boot dont have bmp command. ow can I fix this.

Hello all ! I connected relle to pins (Physical): Relle Orange in 35 gnd 6 ucc 2 But it is constantly active (on), although the port status 32 is off (0). Why is that? # gpio write 24 1 Changes the port status, but has no effect on the relay. Relle ist ON alweys! If you physically disable the pin (in - 35), then the relay is turned off. I just installed the system. I did not install any additional services and packages. Maybe I need to configure something in the system to activate the GPIO?

Hi, Please help to setup W5500 Ethernet board on Armbian (Orange PI Zero). My config: $ cat /boot/armbianEnv.txt verbosity=1 logo=disabled console=serial disp_mode=1920x1080p60 overlay_prefix=sun8i-h3 overlays=usbhost2 usbhost3 spi-spidev param_spidev_spi_bus=1 rootdev=UUID=4a65461e-d8ac-4d8f-94c0-05ecd12f6d58 rootfstype=ext4 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u I can see spi: $ sudo ls -l /dev/spi* crw------- 1 root root 153, 0 Nov 3 22:32 /dev/spidev1.0 But no eth1... Maybe I need to install some "user_overlays"? I was trying to use "anyspi" and "w5500" overlays from Raspberry Pi but failed..…

Dear Armbian community, First of all, I am aware of the fact that what I am trying to achieve is not supported, but let me ask anyway. What I am trying to do is to build my custom root filesystem for my specific embedded needs (which is pretty minimal and without systemd) while still using kernel (5.8.16-sunxi) and modules provided by Armbian. It is going great so far, but the first issue I need to figure out is why there are approximately 60 second delays between each brcmf_fw_alloc_request calls (full dmesg available here): [ 40.602927] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43430-sdio for chip BCM43430/1 [ 40.620798] brcmfmac mmc2:0…

I successfully installed Armbian Focal¹ on my Neo Core 2 with MiniShield² and SSD. I find no issues after booting boot from SD-card. But I fail to boot from eMMC with System on SATA using nand-sata-install: In the serial console i see the boot process to stick after «Started udev Kernel Device Manager». Any hints how I can unblock from here? [...] U-Boot 2020.04-armbian (Sep 02 2020 - 09:50:54 +0200) Allwinner Technology CPU: Allwinner H5 (SUN50I) Model: FriendlyARM NanoPi NEO Core 2 DRAM: 512 MiB MMC: mmc@1c0f000: 0, mmc@1c11000: 1 Loading Environment from FAT... Unable to use mmc 1:1... In: serial Out: serial Err: serial Net: …

I am considering the purchase of an Orange Pi 3 and I was wondering how well it is supported by the current Armbian image. According to https://linux-sunxi.org/Linux_mainlining_effort it should work mostly fine. How well does Panfrost run on the board? Are there any gotchas that I should be aware of? Thanks.

Hi, I'm using a CubieTruck running Armbian 5.8.16. /dev/ttyS2 works fine if I use the 4.19.62 dtb but not when using the 5.8.16 dtb. I am using the uart2 overlay and param_uart2_rtscts. If I try to access the port with picocom it reports "Filedes is not a tty". Commenting the param_uart2_rtscts line makes no difference. It appears that uart2 isn't being setup as a serial port when using the 5.8.16 dtb (and overlays). But the kernel must be okay because it works with the old dtb. Does anybody have a solution here ? Or can you tell me where the sources for the dtb and overlay are ? The copies on github seem old. Thanks, S…

Hello I have an Orangepi One which fails after running for a certain time. In the failed "state" pinging it still works, but SSH connections to the Orangepi or from the Orangepi to the Server via Autossh won't work any more. A PHP application running on it is still working. It looks like the issue is that it winds back the time to something ridiculous. Hard reset with pulling Power fixes this for again a certain time till it happens again. I wrote a script which runs every Minute via Cronjob and logs the current time to a file. Before the rewind already something weird is happening. The cronjob is executed twice on 04.40. I have no idea what is hap…

Hello, I've a olimex lime2 rev.K board and i installed Armbian 20.08.0-trunk (Bionic-minimal) which is having ... Kernel Version : 5.4.51-sunxi (branch -> next ) u-boot : v2020.04 I've serial console on which I can see that board boot correctly. I want the board to show information and login prompt on HDMI output...but HDMI losses on boot when kernel loads, Part way through Kernel load looses monitor sync signal and monitor goes blank. Can sometimes get back for short period (5-10 seconds) if unplug/plug HDMI cable but still looses sync and monitor doesn’t detect that anything is connected. I spent a lot …

Hello everybody! I upgraded my armbian on my Bananapi M1 to... armbian 20.08.17 Buster with Linux 5.8.16-sunxi Unfortunately I don't have any internet access anymore now. I can still SSH into the board, but I can not ping any server with it. What more information do you need to help? Thank you very much for your attention!