Other families

Dear all, I'm just trying to get a HummingBoard-Edge (i.MX6 Quad, 2GB) working with Armbian_5.20_Cubox-i_Ubuntu_xenial_4.7.3. Unfortunately, the board is recognized as CuBox-i, U-Boot loads the wrong dtb file (imx6q-cubox-i.dtb) and I have no access to the internal eMMC card (mmcblk1). By the way, it's the same issue with ArchLinuxArm. Do I have to somehow modify the U-Boot environment variables to get the board being recognized as Hummingoard2? Do you have any other ideas? Thank you very much for your help! Best regards Andreas

I flashed my uSD card with armbian ubuntu desktop and works fine, until I do an apt upgrade. After that, I always see a boot message saying: Unable to handle kernel NULL pointer derefence at virtual address 00000010.... Internal Error: oops: 17 [#1] SMT THUMB2... etc etc If I try doing startx, I see something else... (EE) modeset(0) failed to initialize glamor at ScreenInit() time. .... AddScreen/ScreenInit failed for driver 0.

Hi i have an udoo quad and i downloaded your os (ubuntu jessie desktop Kernel 4.0.8). At first congratulation for your work and big thanks to share it After the flash of the sd card (used win32diskimager because imagewriter don't work for me), i can started my card. Ethernet, wifi, browser ... works fine ! Now, that it didn't work is sata disk or usb disk. When i plug it on the card nothing appear. If i go to /media i saw nothing. Do you know how to resolve this ? Otherwise, i would like to compile Qt5.5 but i need the header for openGL librairie to do it. Is it possible to have it (i saw nothing on /usr/include) ? Last think, do you plan to make a try with the new …

Hi Igor, I want to compile a new kernel on HB. I do following steps: export ARCH=arm export CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf- make imx_v7_cbi_hb_defconfig make If make is in process, I become an error: /bin/sh: 1: /usr/bin/arm-linux-gnueabihf-ld: not found make[1]: *** [init/mounts.o] Error 127 make: *** [init] Error 2 how can I fix that?

Hello, I am trying to run urbit on my CuBox-i 4×4 and it looks like ARMBIAN 5.25 stable has some kind of kernel config that limiting the memory usage: ./urbit -c mytestcomet ~ urbit 0.4.4 urbit: home is mytestcomet boot: mapping 2048MB failed see urbit.org/docs/using/install for adding swap space I have added a 4GB swapfile but it seems it's not addressable by the urbit process, I also tuned the setting vm.swappiness without any success. Could this be related to the kernel config CONFIG_VMSPLIT_2G? Details: ---- Kernel setting cat /proc/config.gz |zcat |grep -v "^#" |grep VMSPLIT CONFIG_VMSPLIT_2G=y top top - 20:24:55 up 4 min, 1 user, l…

I'm running the ubuntu trusty image on a Hummingboard-i2eX and am experiencing 2+ minute boot times. The system starts booting and I get the following output before it hangs. [1.6xxxxx] imx-ipuv3 2400000.ipu: WARNING: adapt panel end blank lines [4.2xxxxx] IR keymap rc-rc6-mce not found I am assuming that it is something related to the IR keymap that is holding the system up, but am not certain. Any thoughts on getting a slightly faster boot?

Hi Friends Recently I have been trying Armbian 23.5 as alternative for NVIDIA official images. Tried both Ubuntu Gnome desktop and Debian Cinnamon desktop builds but somehow non of them discovers HDMI output. When Jetsno Nano is booting up I can see official "NVIDIA" screen for a while and then information about missing input (from TV on a TV). The hardware itself works OK - when I change SD card to one with an official image or another one with Debian 11 official - it works just fine. It's seems like a problem with Armbian build itself. Any advice is much appreciated. Kuba Logs: https://paste.armbian.com/omiher…

I'm currently working on getting a custom kernel (5.4 kernel which was modified for a specific need regarding containers) running on a Jetson Nano. I've tried running the kernel image on NVIDIA's Jetpack but that didn't work. I've tried building the image directly on the Nano running Armbian and it hasn't really worked so far. It seems to either brick the Nano or not update the kernel version after an install (depending on if I replace /boot/Image). Would you all have any suggestions of what I can try or if it’s even possible? Thanks in advance!

Hello! I'm trying to boot latest releases of of Armbian (following images: Armbian_21.02.3_Cubox-i_buster_current_5.10.21.img and Armbian_21.02.3_Cubox-i_focal_current_5.10.21.img) on a Solid-Run Hummingboard2 Gate V1.4 board. (Board V1.2 freeze during Uboot) I'm getting to the "Starting kernel" message but after that things stop. Switching on the verbose output in ArmbianEnv.txt result in the output below where the kernel always stop at message: [ 0.000000] Freeing unused kernel memory: 2048K Do anyone have any thoughts/ideas here on what could possibly be the problem stopping the kernel from booting? U…

Hi: I recently installed Buster xfce desktop on Cubox i4pro. Everything works great, except I can not power off cubox. I tried various commands, shutdown -h now; systemctl poweroff; and hatl; but the system first appears to halt, where I can not ping the ip addrss of cubox, but then it reboots. Is there some way to powerfoff cubox? My current system is nightly, but I also tried stable with latest kernel. $ uname -r 5.10.21-imx6 $ cat /etc/os-release PRETTY_NAME="Armbian 21.08.0-trunk.26 Buster"

Hi there! I recently installed Armbian (Stretch: Armbian_5.83_Nanopifire3_Debian_stretch_next_4.14.115) on my new NanoPi Fire3. I was able to boot, but it responds so slow, that it is unusable! For example, when I SSH into it, it takes a log time to show me the login prompt. When I enter the username and press enter, it takes about 5 seconds to ask me for password. When I enter password, it takes about 10 seconds to show me the Armbian banner. I wasn't even able to go past the changing of unix password on first login, because it just "froze". I have installed the image twice on my SD card, just to make sure it isn't a corrupted install.…

I bought several modules with mpc8308 on board. But following the documentation, i did not manage to implement DMA data transfer. Is it possible to get an example of the implementation of data transfer over DMA?

Hi, when booting Armbian Sid minimal rolling 6.1.11, there is no serial console login. Console output: Found U-Boot script /boot/boot.scr 1993 bytes read in 146 ms (12.7 KiB/s) ## Executing script at 12000000 93 bytes read in 94 ms (0 Bytes/s) 38318 bytes read in 2603 ms (13.7 KiB/s) 33621022 bytes read in 3482 ms (9.2 MiB/s) 11215360 bytes read in 1257 ms (8.5 MiB/s) ## Loading init Ramdisk from Legacy Image at 14800000 ... Image Name: uInitrd Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 33620958 Bytes = 32.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flatte…

Hi. I am working with an Olinuxino A20 micro, but I have issues with the SPI bus. I hope somebody can help me to find a solution. I used Armbian 23.5 Bookworm with kernel 6.1 In sclk signal i have a pulse before to start the data transmission, I required the SPI to communicate a LoRa module but the pulse before of data generate that doesn´t work the LoRa module. I attached the signals.

Looking for Armbian_20.02.7_Cubox-i_bionic_current_5.4.28_desktop.7z – anyone can share a copy

I have a Cubox-i (older 2GB version) running Armbian_5.00_Cubox-i_Debian_jessie_4.4.1.zip. It's using a SATA drive as root. I've installed some services that take up a lot of CPU. After a couple of days, it still responds to pings, but I can no longer log into the box with SSH. I'm forced to power cycle it to log back in. Looking at it, there's nothing in the logs to point to the problem, the only weird thing in /var/log/messages is: Feb 22 12:34:47 localhost rsyslogd-2007: action 'action 17' suspended, next retry is Mon Feb 22 12:36:17 2016 [try http://www.rsyslog.com/e/2007 ] I do wonder if it's overheating due to the CPU use. Is there anything I can do to tra…

Hi, I tried everything: I downloaded wheezy isos, Jessie.... with GUI, no GUI and then I installed by myself..... solid-run isos and armbian isos.... just clean system... burn the iso in a sdcard and run the system.... if it has already GUI I install blueman and test bluetooth and wifi.... perfect. If doesn't have gui then I install one (I tried xfce and mate), then blueman and test bluetooth and wifi.... perfect. then 'apt-get update && apt-get upgrade' and bluetooth stops working Any reason for that and any tip?

Hello How to rotate screen HDMI ? 4.7.3-cubox

Hi All, Looking for assistance with getting an old SmartQ5 Mobile Internet Device running with Armbian. I was able to locate Github page (https://github.com/tpruvot/smartq-magicsd) which references booting from SD but need assistance getting armbian compiled and configured for the device. Any help is appreciated! SPECS: Samsung Mobile Application Processor S3C6410 based on ARM11 core at 667 MHz/800 MHz 128 MB DDR 133/333 MHz SDRAM 1 GB NAND FLASH (256 MB usable for storage) AC97 audio codec & PCM 24-bit audio SoC graphics unit, OpenGL ES 1.1/2.0, 4M triangles/sec @133Mhz (Transform only) Integrated Wi-Fi 802.11b/…

Hi all, I got my hands on an Odroid XU4 and wanted to use it as a replacement for my RPi 3 for all my amateur radio related stuff. Unfortunately all of the AX25 kernelmodules have been left out of official builds. I have a commit ready to add them back, yet I am not sure what the actual process is to submit a PR. As I understood I need to open an issue first yet I cannot figure out which category this fits in. I attached a patch file for current kernel. Thank You, Geoffrey ax25.patch

See the following steps to get the TI wl18xx drivers to work on the Cubox with the I4P Rev 1.5 SOM. Step 1) Boot with the Armbian base image (Armbian_5.20_Cubox-i_Ubuntu_xenial_4.7.3). The 3.14.79 base image also works however will require a different dpkg install command to overwrite the 3.14.79 kernel. Step 2) Build a new kernel with Armbian build tools, note this only works with the 'DEV' kernel branch because SolidRun provides all the necessary DTS files. Edit the compile.sh script and change KERNEL_CONFIGURE="yes" to customize the kernel configuration. The relevant modules you will need to select are: CONFIG_WL_TI=y CO…

Are there any other Mekotronics R58 mini users out there? I like this box a lot and Armbian runs great on it, I would very much like to share expereriences with other users and learn from each other. At this point Armbian is downloadable for this board on this site. And it has recent updates too. Some specs: I have the Mekotronics R58 mini plastic version (there is also metal box that has better cooling but same internals) RK3588 8 core Rockchip CPU 4Gb RAM File System transferred to 120Gb SSD with armbian-config Measured it uses 2.1 watt during idle I seem to have everything working except HW acceleration. On the download page…

Hi, I installed latest Jessie desktop version on Cubox i4Pro but audio via HDMI still does not work... Any solution? Thanks

[WIP] Schematics Pros: - board vendor provides dev samples and documentation - working with latest mainline kernel - many variants by the same vendor - official SDK/BSP currently on 4.4 - no unreliable shitty Micro USB for DC-IN but GPIO by default Cons: - new platform needing more initial work - not many active developers

Hi, When I tried booting the vanilla kernel, downloaded from http://www.armbian.com/hummingboard/, on my Hummingboard i4 Pro, I get the following error message from u-boot: ERROR: Did not find a cmdline Flattened Device Tree Could not find a valid device tree Booting from net Has anyone else seen the same issue? Thanks.

Hello everyone, I am a beginner in Linux. I have a Hummingboard i2ex and I am running Armbian_5.30_Cubox-i_Ubuntu_xenial_4.11.4_desktop on it. Trying to use a CSI Tool, I have to compile and install this kernel : https://github.com/xieyaxiongfly/Atheros-CSI-Tool.git Here are the steps that I did on the Hummingboard: ( you can see the tutorial: http://pdcc.ntu.edu.sg/wands/Atheros/document/Atheros-CSI-Tool-User-Guide.pdf ) 1) sudo apt-get install git (to clone the source) 2) sudo apt-get install libncurses5-dev libncursesw5-dev (to run makemenuconfig) 3) git clone https://github.com/xieyaxiongfly/Atheros-CSI-Tool.git 4) Enter the dir ~/Atheros…

Hi I moved from 3.14 to 4.13. In 3.14 I had a imx framebuffer , needed for my lvds LCD In the 4.13 kernel menuconfig i cannot find a way to set CONFIG_FB_IMX. How to enable this? Dig

I've recently upgraded Armbian on my Cubox-i using apt, i.e. that was not a new clean install. As a result I still have an old kernel running. What is the right way to upgrade kernel? Edit: updated using armbian-config, everything seems to be ok.

When cubox is configured to run wifi, it takes 60+ seconds for it to start up with no network cable plugged in. Where as when I plug in a network cable to the network port it will start up under 10 seconds. Hardware: Cubox-i4 Pro Running Ubuntu Trusty image found here: http://www.armbian.com/cubox-i/ Any advice would be appreciated.

Foreward: Not sure if this better fits in board bring up, but I can't post there, so feel free to move if appropriate. I'm looking into the feasibility of using the Armbian build system to generate OS images for the Avnet MicroZed board. This board is based on the Xilinx Zynq 7000 platform, which is a SoC made up of a dual core 500 MHz CPU, and a Artix-7 generation FPGA. The CPU is nothing to write home about, but the FPGA opens up an interesting array of possibilities. Just in case you need an ARM board with 100+ GPIO, over two dozen serial ports, or your own function generator. Really, you're limited only by pin count, FPGA fabric usage, and what you can man…

Hi, I'm trying to use desktop community build for Windows dev kit 2023 but it is not working. Current image: Armbian_community_24.8.0-trunk.554_Wdk2023_noble_wdk2023_6.7.0-rc6_gnome_desktop.img.xz When using etcher to flash to usb, it will flash but fail at validation step say "Cannot validate, the image could be corrupt" or something like that. If still use that usb in WDK, it won't boot. The lite version Armbian_community_24.8.0-trunk.554_Wdk2023_bookworm_wdk2023_6.7.0-rc6_minimal.img.xz is still working fine.

Hi everybody, I'm new here and I would like to ask you for help with make armbian work on other board - Toradex Colibri iMX6DL with freescale iMX6 processor. They already have U-boot & Angstrom linux on NAND (where I would like to get armbian). They have meta-packages and images available for download on their website and I would like to know what is the best way to make it work (to keep their HW configuration)? I like these boards because of good desing and good HW, but this Angstrom linux isn't good... Thank you for every advice

Hi there, Just loaded Armbian Vanilla Jessie (5.00, 4.4.1 kernel) on one of my Cuboxes. There's no sound from SPDIF, even though it's seen: root@cubox-i:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: SPDIF [integrated SPDIF], device 0: S/PDIF PCM snd-soc-dummy-dai-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 Speaker-test shows no errors: root@cubox-i:~# speaker-test -r 44100 -F S16_LE -c 2 -D hw:0,0 speaker-test 1.0.28 Playback device is hw:0,0 Stream parameters are 44100Hz, S16_LE, 2 channels Using 16 octaves of pink noise Rate set to 44100Hz (requested 44100Hz) Buffer size range from 64 to 16384 Period size range from 32 to 8192 …

Hello, I have a brand new cubox-i4x4 and am attempting to install Armbian Stretch mainline kernel 4.15.y I downloaded the image from https://dl.armbian.com/cubox-i/Debian_stretch_next.7z used keka and etch to extract and write image to the SD card. After installing the SD card in the cubox and powering on, it gets stuck at: U-Boot SPL 2017.11-armbian (Jan 24 2018 - 22:39:16) Trying to boot from MMC1 U-Boot 2017.11-armbian (Jan 24 2018 - 22:39:16 +0100) CPU: Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz) CPU: Extended Commercial temperature grade (-20C to 105C) at 24C Reset cause: POR Board: MX6 Cubox-i DRAM: …

Until yesterday my humminboard 1 i2ex worked without any flaws. Now after a restart I cannot access it via ssh anymore. I thought the Ip adress my have changed somehow cause I also restarted my router but it under active clients in router webif either. Also no video output via hdmi...guess that's normal since it's a debian server image. What I can see is the uboot showing up the count down, just quick, I could read ..wrong image format..and something with source.. that's it. Then screen turns black. I have the rootfs on msata ssd and if I remember correctly I removed all other unnecessary files from micro sd card many month ago. I…

I have lots of HummingBoards 2 Edge with eMMC but now got a batch with the new SOM 1.5 and eMMC the original u-boot from next and stable branch (2013-10rc4) get stuck on SPL from time to time on the new SOMs so I'm trying the dev branch which has this new patch: https://github.com/armbian/build/blob/master/patch/u-boot/u-boot-cubox-next/U-Boot-mx6cuboxi-add-support-for-detecting-Revision-1.5-SoMs.patch Copying SPL and u-boot.img to eMMC and booting produce the following: U-Boot SPL 2018.03-armbian (Jun 07 2018 - 16:06:14 -0400) Trying to boot from MMC1 Card did not respond to voltage select! spl: mmc init failed with error: -95 SPL: fail…

Hello I have a nanoPc t3 plus board and I cannot boot it. I searched and I found a related topic that has the same problem but there is no answer. I believe the problem is because of different mem chip but the same revision (1709) Can boot armbian whit compiled friendlyArm Uboot? topic URL my memory chip picture and logs (from the topic) \

Recently I took my old Hummingboard and to run Armbian on it. I chose the desktop-version for Hummingboard using mainline kernel (presently 4.11.6-cubox). Unfortunately Armbianmonitor shows high CPU -temperature. It gradualy builds up, starting from 50 degrees next to 70 degrees, eventualy approaching 85 degrees and then it shuts down. I use the passive heatsink that came with the board and no case. I use it for light desktop things like browsing the internet. Is there something I can do to prevent this, is there something in the kernel like throttling when the board reaches a certain temperature? Thanks again for a great OS, I think you are doing an outstanding…

The alpha version of Armbian images for Orion O6 is available. To launch, burn to a USB flash drive, connect to Orion O6 and turn on the power (installation on NVMe has not yet been verified). The system starts automatically. Important. Image output to the monitor works only in graphical mode (in images with DE). Console output currently only works in UART, so you need a UART console or SSH connection for initial startup. Launching the desktop and displaying the image on the screen can take 30-80 seconds, depending on the speed of the media. https://disk.yandex.ru/d/gedMM0eLiURrjA Armbian-unofficial 25.05.0-trunk Noble ttyAMA2 orion-o6 …

With build from 26th of August, kernel 3.14.14 (cli, debian jessie) I cannot see any hdmi output. When cubox i4pro boots, it shows uboot env and I can interrupt boot, hdmi works well. starting kernel puts monitor into powersave mode. everything else seems to work, I can ssh to the cubox and see the logs, which look normally, e.g. I have tried bpp 16 or 24 when default 32 didn't work root@cubox-i:~# egrep 'mxc|hdmi|fb0' /var/log/kern.log Jan 1 01:00:20 localhost kernel: [ 0.000000] Kernel command line: root=/dev/mmcblk0p1 rootfstype=ext4 rootwait console=tty1 video=mxcfb0:dev=hdmi,1920x1080M@60,if=RGB24,bpp=16 rd.dm=0 rd.luks=0 rd.lvm=0 raid=noautodetect pci=…

I set up NanoPC-T3 as a router, the upsteam Ethernet port is connected to a router. However, the bandwidth drops dramatically whatever I’m using IPTables or network bridge to forward the data. This doesn’t happen on the other SBCs I have. How can I solve it?

I downloaded Armbian for a Udoo Quad from https://dl.armbian.com/udoo/Focal_current_desktop. uname -a reports: Linux udoo 5.6.18-imx6 #20.05.4 SMP Mon Jun 15 00:30:23 CEST 2020 armv7l armv7l armv7l GNU/Linux However in https://docs.armbian.com/Hardware_Freescale-imx6/ I read: "Udoo Quad Kernel 3.14.x and 4.4.x with some hardware support, headers and some firmware included", which suggests that the image should have a 3.14 or 4.4 kernel. In /var/log/Xorg.0.log I read: [ 21.345] (II) AIGLX: Screen 0 is not DRI2 capable [ 23.279] (II) IGLX: Loaded and initialized swrast [ 23.279] (II) GLX: Initialized DRISWRAST GL provider for screen 0 LIBGL…

Hi community I have a HummingBoard2 and installed Armbian on SD (first boot device). And everything works really fine! !!!Thanks a lot for the perfekt installation routine!!! Afterwards i tried to install from SD to eMMC with the "sata-nand-install.sh" script. Installation completes without errors. If i boot with inserted SD card the system boots from SD without errors (for a fused (0x5=2840 and 0x6=10) IMX6Solo and also with unfused module) - fine! If i remove the SD card and use a fused (0x5 = 3040 and 0x6=10) IMX6Solo module, i think it tries to boot from eMMC but it doesn't work. When i try to boot with inserte…

Hi, Since I upgraded my kernel to version 4.19 (`linux-image-next-cubox=5.73` when I tried I think) on my cubox-i4 pro, I lost HDMI : root@cubox:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: SPDIF [Integrated SPDIF], device 0: S/PDIF PCM snd-soc-dummy-dai-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 Anyone experiencing this too ? Downgrading to `linux-image-next-cubox=5.60` solved it. apt install linux-image-next-cubox=5.60 reboot aplay -l **** List of PLAYBACK Hardware Devices **** card 0: SPDIF [Integrated SPDIF], device 0: S/PDIF PCM snd-soc-dummy-dai-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: DWHDMI […

Hi There, I would like to run Linux5 or Linux6 on Jetson nano, display using HDMI-DVI adapter. It worked fine with Jetpack4 (=Linux4). When I boot with armbian/Linux5.10, which is linux-image-current-jetson-nano, the display tells me it is out of sync then I would force the display as 1280x1024@60Hz, since it looks like Linux fb or X11 are trying to use 1280x1024@75Hz, so that I need edid/1280x1024.bin (maybe with video=1280x1024@60) using {linux-source}/tools/edid to maintain the resolution and sync. I tried both of gcc-10 and gcc-9 to build it, but failed with below error: edid.S: Assembler messages: edid.S:274: Error: cannot represe…

On my Cubox, can I upgrade Armbian Bionic to Cosmic? Is that going to work? I'm not using any GUI / HDMI stuff, so that is not relevant for me Reason of my question: I want OpenSSL 1.1.1 (with TLS1.3), which is a part of Cosmic (and not of Bionic).

Maybe I missed something, it's been a few weeks since I needed to install an image. cubox with hdmi does not boot. There is no serial port, so I can not even try to figure it out. Also it never requests an ip address from the router. Tried with trusty legacy and vanilla. Used the link specifically labeled cubox-i http://www.armbian.com/cubox-i/

Hello, I updated my Vanilla Jessie headless install yesterday (aptitude safe-upgrade), but the system never came back online after reboot. The screen flashes the SolidRun logo and a few lines of text, and then the LED turns off and the screen goes blank: It doesn't seem like the system boots, and it definitely doesn't connect to my home network via Ethernet. Is there a way to rescue this install? Thanks in advance, Matteo

How to Reset armbian 24.5.1 jammy, the device long time I not power on, but just now I power on can't log with ID Root & Password 1234. already many things still can't resolve it. If have any suggestion please let me know.