Reviews, Tutorials, Hardware hacks

I was chatting with @tido about ways to help the Armbian community and I came up with the idea of a common C library to access the I2C, SPI and GPIOs of all supported boards. There are of course kernel drivers to communicate with these things, but there are differences between boards that this API could help smooth out. For example, different CPUs (and boards) map the GPIO pins very differently. Projects such as WiringOP and WiringNP try to copy the Raspberry Pi library, but this is also flawed because it's based on the BCM283x GPIO numbering. What I propose is to create a set of simple functions for accessing GPIO pins using the physical pin number as a reference. On all…

The pyA20 gpio library is quite famous when people start to play with gpios , spi or i2c on sunxi boards but mapping needs often adjustments to work on your own board. This situation is not really friendly for 'beginners'. pyGPIO should help to make armbian a little bit more 'IoT friendly'. I didn't touch the 'backbone' of pyA20, so the syntax should be similar to its original (except pinname when using port instead of connector). How can I use this library: Cause all of this boards have (more or less) the same pinheader (sometimes other pins are deployed on the pinheader) pyGPIO tries to unify the mappings, so that code can be shared and deployed …

Edit: User Space IO depracated. Use Java Periphery instead https://github.com/sgjava/java-periphery https://github.com/sgjava/userspaceio After a lot of work and testing I have produced the User Space IO project! It provides Python 3 and Java 8 bindings for Linux user space GPIO, SPI, I2C, PWM and Serial interfaces. This allows cross SBC and cross language development using a common API. I took two best of breed C APIs for Linux user space libgpiod and c-periphery and produced CFFI bindings for Python and JNA bindings for Java. Since all the bindings closely match the C API it's easy to move from language to language. The side effect of using the J…

Access to a console can be mandatory when you SBC doesn't work as expected (e.g Network or HDMI output doesn't work). When SSH/Display access isn't possible access to console via UART is the best way to get a clue where your SBC hangs. This short tutorial should give you an introduction how this works. For some boards, armbian implements an USB gadget mode (a 'fake' serial console over microUSB) describen below. As a reminder an USB-UART bridge is always prefered over USB gadget mode whenever possible (UART get's initialized before the gadget driver and also before HDMI, means even if you don't get a proper output from HDMI or gadget mode console, it is possible that UART…

(disclaimer) No itention to make a Frankendebian (https://wiki.debian.org/DontBreakDebian) but ubuntu package "zram-config" works perfectly. I tested it for two weeks in a: Orange PI Zero 512MB Armbian Stretch 5.40 4.14.18, Orange PI PC2 Armbian Stretch 5.40 4.14.18, AMD Sempron microserver Debian Stretch 9.4 4.9.0-6-amd64. A short tutorial: 1. Download zram-config package (it's a universal package, it does not matter the architecture in use) wget http://de.archive.ubuntu.com/ubuntu/pool/universe/z/zram-config/zram-config_0.5_all.deb 2. Install it sudo dpkg -i zram-config_0.5_all.deb 3. Remove the installer …

Hello im new and im Italian so i hope you will not hate me if i write not perfectly (Who said Google Translate?? No No No) This Guide is for a "client to client" setup of the box, we will internally switch Wifi to Eth, so a working computer can access internet from its eth port even if the router signal source is wireless. Router AP -----> ARM BOX [WIFI internal or usb dongle] ===>> internal eth0 ------> ethernet cable --> client eth port Make sure WiFi in arm box is connected using nmtui command FROM NOW ON <WIFI CARD> is the wifi adapter name es: replace "<WIFI CARD>" with "wlx0013eff301ee" …

because of some value changes for buster updates via apt (or buster going stable) N: Repository 'http://security.debian.org buster/updates InRelease' changed its 'Version' value from '' to '10' E: Repository 'http://security.debian.org buster/updates InRelease' changed its 'Suite' value from 'testing' to 'stable' N: This must be accepted explicitly before updates for this repository can be applied. See apt-secure(8) manpage for details. Do you want to accept these changes and continue updating from this repository? [y/N] Y N: Repository 'http://cdn-fastly.deb.debian.org/debian buster InRelease' changed its 'Version' value from '' to '10.0' E: Repository 'http://cdn-f…

I did that on a NanoPi Neo with the FriendlyARM PCM5102A Hat ( https://www.friendlyarm.com/index.php?route=product/product&amp;product_id=169 ) using kernel 4.14.87-sunxi and armbian 5.67 (or later would be only 5.65?) (before that I did use legacy kernel 3.4.x with the PCM510A) and the armbian-BuildSystem plus (THANKS to) informations in threads from @dony71 , @Christos, @Valery Rezvyakov and the the Reference-Threads you could find above ---------------------------------------------------------------------------------------------------------------------------------- BACKUP DTB (on NanoPi Neo) --------------------------------…

The above thing is a $10 accessory that can be ordered together with ROCK64 (and maybe other Pine Inc. devices like Pine64 or Pinebook?). It's an USB-to-SATA bridge (JMicron JMS578 based) to be used together with 2.5" SSD/HDD or 3.5" HDD. For the latter purpose it's equipped with a separate power jack suitable for the usual 12V 5.5/2.1mm power barrels (centre positive) you find PSUs with literally everywhere. TL;DR: If you want to add storage to your ROCK64 order this cable too. It works great with both 2.5" and 3.5" disks and it's somewhat sad it's not available separately since it's a great storage companion for many other devices too. Basics fir…

Anyone ever dealt with OpenMediaVault (OMV) on SBC? Great piece of software but pretty slow, right? One of the many reasons why that happened are outdated crappy kernels and bad settings. I looked at an OMV image for A20 based boards like Banana Pi Pro recently, ended up here http://simplenas.com/download/bananas-simple-system and simply thought: Are you kidding me? Your stable release is based on horribly outdated Debian Wheezy, a kernel 3.4.something and a 2.x OMV release?! What a mess... Igor had an OMV install routine since a long time in his Debian-micro-home-server post-processing script but since an Armbian user evaluated using Armbian's build system to…

Today I had the pleasure of benchmarking an ARM64 server. This server has been made available for Armbian to test native ARM64 image building. I knew nothing about the server. Nobody told me any details. So everything was an adventure for me to find out. I got SSH access, so my research began. A lscpu informed me it had 32-cores all clocked at 3.3Ghz. Spoiler nicod@worksonarmbian:~$ lscpu Architecture: aarch64 CPU op-mode(s): 32-bit, 64-bit Byte Order: Little Endian CPU(s): 32 On-line CPU(s) list: 0-31 Thread(s) per core: 1 Core…

Not much of a tutorial, but it is something that often needs some googling and head scratching. This is how I got my particular modem working, your mileage may vary. Step 1) Get a modem that will work. I got a Huawei E397u LTE/UMTS/GSM modem. It's Cricket branded, but I'm on Google Fi, it will work with my data SIM. Step 2) Plug it in and see that it doesn't work. Step 3a) apt update Step 3b) apt upgrade Step 4) Install usb-modeswitcher Step 4, optional part 2) install modem-manager, modem-manager-gui (for general playing around) Step 5) unplug/replug the USB modem, see that it should magically have a different VID:PID when …

I do some tests on a new display from WaveShare : 5.5inch HDMI AMOLED, 1080x1920 https://www.waveshare.com/product/modules/oleds-lcds/oled/5.5inch-hdmi-amoled.htm On the wiki, it's wrote : To use it on RaspberryPi, you must change the config.txt file for to ajuste hdmi parameters : https://www.waveshare.com/wiki/5.5inch_HDMI_AMOLED max_framebuffer_height=1920 max_usb_current=1 config_hdmi_boost=10 hdmi_group=2 hdmi_force_hotplug=1 hdmi_mode=87 hdmi_timings=1080 1 26 4 50 1920 1 8 2 6 0 0 0 60 0 135580000 3 I do it and that working fine I add this to ajust resolution max_f…

A very hackish port exists of this Raspberry PI RGB LED Matrix Library which works for Allwinner H3 devices. This works by bit-banging 14 GPIO pins simultaneously to achieve about a 10Mhz throughput / 100fps refresh rate. Refer to here: https://github.com/mrfaptastic/opi-allwinner-h3-rgb-led-matrix I managed to easily get up and running using an Orange PI. Refer to the README of the github repository.

This falls somewhere between "how-to", "research", and "development", so I stuck it here. @adafruit is working to target CircuitPython to Armbian devices, something that will be a bit of a task. I've been playing with the code to get it working on my Tritium H3, finally did (some extra sudo-ing was needed), so I'll probably toss in a couple board definitions/help here and there if I can. it had hijacked a C2 thread (not completely, it was at least about using it on the C2), and I thought it best to continue discussion here. @chwe, @sgjava, and @Larry Bank all have various experience with various GPIO tools, their interest may vary. My current observations,…

This will cause update-grub to add the following a devicetree line to all menu entries. This example is based on Debian Trixie's grub-efi. This example will expect dtb directories (or links) to be in the /boot directory, using the convention that I've seen Armbian use. Here is an example of a /boot directory listing for (pure) Debian Trixie with two kernels: -rw-r--r-- 1 root root 336036 Aug 27 04:10 config-6.12.43+deb13-arm64 -rw-r--r-- 1 root root 343394 Sep 6 12:48 config-6.16.3+deb13-arm64 lrwxrwxrwx 1 root root 42 Sep 20 16:17 dtb -> ../usr/lib/linux-image-6.16.3+deb13-arm64/ lrwxrwxrwx 1 root root 43 Sep 20 16:17 dtb-6.12.43+deb13-…

Hello, I am trying to connect an enc28j60 ethernet port to spi0.0 on an orange pi pc, running armbian (debian stretch 4.19.5). I have the jumpers all connected in what I believe is the correct pattern. I compiled a device tree (overlay?) for the enc28j60 on h3, the dtbo file now exists in /boot/overlay-user/spi-enc28j60.dtbo. /dts-v1/; /plugin/; / { compatible = "allwinner,sun4i-a10", "allwinner,sun7i-a20", "allwinner,sun8i-h3", "allwinner,sun50i-a64", "allwinner,sun50i-h5"; /* This fragment is required only if the IRQ pin requires internal pull-up */ fragment@0 { target = <&pio>; __overlay__ { enc28j60_pins: enc28j60_pins…

Hi Yesterday I spend the whole day to install Armbian Desktop (XFCE) on my Pinebook Pro. Why Armbian ? The PBP was delivered with Manjaro Arm on it. Everything worked fine until Manjaro stopped support for the Arm platform. For about one year there is no update on stable and the unstable branch couldn't establish a connection to Wifi. I used Manjaro Arm to install tow-boot to the SPI following this website: https://forum.pine64.org/showthread.php?tid=17529 I downloaded the current Bookworm XFCE edition and wrote that to an SD card. Booting from the SD with tow-boot went fine. I installed armbian on the SD card and used armbian-conf…

Hi all. I again had the pleasure of working with an amazing server. This time the AMD Threadripper 3990X, 64-cores and 128 threads. After last week working on a 32-core ARM server I thought I had seen performance. This is again not comparable with anything before. I again got private SSH access. So I opened 3 terminals. One with HTop, another to check sensors. And the 3th to execute my benchmarks. First thing I saw were the 128-threads. Being used to seeing 6, this was almost unbelievable. Spoiler With light loads it turbo's up to 4.3Ghz. All cores maxed out @ 3Ghz while consuming 400W. Reaching a single core 7zip…

How to delete this message?

Hi all, we have developed a script to create an SD image for Odroid HC4. With this method you can use Armbian without erase Petitboot partition. https://github.com/TheLillo/generate-image-hc4-armbian

With USB camera and Bluetooth headset, mouse and keyboard.

mainline based u-boot 2021.07 Ubuntu 22.04 Jammy LTS based (upcoming release, could have issues, currently in testing phase) kernel 5.10.y LTS or 5.15.y LTS ZSH with OhMyZSH addon or classic BASH ZFS 2.1.y support Wireguard fan and LCD support boot from SPI / HDD / USB Tested on image (which comes with preinstalled headers, stable kernel): https://redirect.armbian.com/odroidhc4/Jammy_current https://redirect.armbian.com/odroidhc4/Jammy_current.torrent apt update and upgrade Spoiler odroidhc4:igorp:# apt update Get:1 http://ports.ubuntu.com jammy InRelease [270 kB] Hit:2 http://…

Hi all, First afore, allow me to express my gratitude to all developers working on Armbian tirelessly. It is amazing how much I can achieve nowadays on these little Arm-based boxes, either SBC or repurposed Android TV box. This in my first tutorial submitted on Armbian forum, as I would like to contribute something back. I will update this post further when I am getting more familiar w/ Armbian & running LibreOffice on it. =========== Platform running: SOC: Allwinner H6 Device: Tanix TX6 compatible TV box - UPDATE Apr 2022 ( Please check out the Allwinner H6 …

Hi all. I've created a tool to install Box86, Box64 and Wine onto Armbian Hirsute 5.13 I've tested it on RK3399. Should work on any device with panfrost drivers enabled. Please let me know on what it works, or if it doesn't. Here is the script. https://github.com/NicoD-SBC/armbian-gaming I also made a video where I show how to use it.

[update 12/2017 at bottom] Possibly late, but I would like to put everything we know in one place for anyone who might think of buying this board. Overview: This is a form factor and (mostly) I/O clone of the Raspberry Pi 3 with a much more powerful quad-core Cortex-A17 Rockchip rk3288. It supports HDMI 2.0, has 2 GB RAM, Gigabit Ethernet, Wifi and BT on board, etc: https://www.asus.com/us/Single-Board-Computer/Tinker-Board/ As numerous other sites have covered all the typical performance metrics and extolled the power and so forth of this board, I'm going to go ahead and give you the less exciting information a…

So, I was doing some reading on how to control PWM fans under Linux. The lm-sensors package has a fancontrol script, but pwmconfig doesn't recognize the PWM devices on my NanoPi M4V2. There's also this repository which has a pwm-fan service, which might be the same one that Friendly Desktop uses (referenced in this post). But then I found this rather interesting link from the Kobol guys: https://wiki.kobol.io/helios4/pwm/. Apparently the Linux kernel has built-in thermal control and user space scripting isn't even required, just editing the Device Tree. But as we have easy user overlays for the RK3399, let's go ... tparys@m4v2:~$ sudo ar…

The above is a so called 'Banana Pi M2 Berry' I bought yesterday and will return today to get my money back (due to 'Irreführende Werbung' / false advertising) showing most probably the use case this device will be bought by clueless people: To connect a SATA 2.5" disk to it since 'native SATA'. Of course this doesn't work as expected since the board's power design is an absolute fail. The manufacturer already knows what a shit show using Micro USB for DC-IN is. I simply used the same average USB cable I used to demonstrate the problem a few years ago with the original Banana Pi. With an average USB cable the disk does not even spin up but only produces ugly n…

Overview (Disclaimer: The following is for techies only that like to dig a bit deeper. And if you're not interested in energy-efficient servers then probably this is just a waste of time ) EDIT: Half a year after this poorly designed SBC has been released just one of the many design flaws has been fixed: Micro USB for DC-IN has been replaced by the barrel jack that was present on the pre-production batches. If you were unfortunate to get a Micro USB equipped M3 please have a look here how to fix this. Apart from that check the Banana forums what to expect regarding software/support first since this is your only source) Sin…

EDIT: 04.01.2020 - Fixed patches to work with latest armbian sources. (references have changed) Hi everybody, Here is a tutorial to enable the Lemaker 7" Touchscreen on BananaPi Pro with Debian Buster and Mainline-Kernel 5.XX.XX. Kernel: Mainline 5.4.6 / Buster Board: BananaPi Pro WebLinks: • https://forum.armbian.com/topic/1905-enabling-lcd-in-u-boot-kernel-472/ • https://forum.armbian.com/topic/1849-touch-driver-banana-pi/ • http://www.atakansarioglu.com/getting-started-bananapi-linux/ • http://forum.lemaker.org/thread-15482-1-1.html • http://linux-sunxi.org/LCD To make the 7"…

With this commit I added 7-zip benchmark reporting to Armbian now. Will be available after next updates and with next batch of new images. Why not recommending to just do an 'apt install p7zip ; 7zr b'? Since 'fire and forget' benchmarking is always BS. You need some monitoring in parallel to know whether your system was really idle and at which clockspeeds the CPU cores were operating (throttling occuring or not?). Most recent 7-zip contains an own routine to 'pre-heat' the system prior to starting the benchmark (to let cpufreq scaling switch from low clockspeeds to highest ones and e.g. on Intel systems let the system enter TurboBoost modes). Th…

Hi all! I've tried Xulong Extension board for Orange Pi Zero and found it useless waste of my money. Almost two months ago I've decided to make my own hacking shield which allows me much more in terms of control and peripherals. I've tested functionality most important to me and I'm pretty happy with result. I2C works, USB power switch works, power measurement works. Project page on GitHub Now I'm in progress making peripherals accessible to the system and user. Userspace tools for python/node/C works and later I will publish tutorial (or more than one) how to make it (because it is not clear to me and take huge amount of…

Hello All After a lot of hours and sleepless nights I was able to get this 5" LCD to work with the BPI-M64 module. 1. Correct resolution setup + environment. A. In /Boot/armbianEnv.txt set the following: Make sure to enter overlays= spi-add-cs1 spi-spidev (this is for the touch panel to work) B. for 180 rotation: extraargs=fbcon=rotate:2 drm_kms_helper.edid_firmware=HDMI-A-1:edid/800x480.bin video=HDMI-A-1:800x480-24@60 No rotation: extraargs= drm_kms_helper.edid_firmware=HDMI-A-1:edid/800x480.bin video=HDMI-A-1:800x480-24@60 C. this info came from: https://askubuntu.com/questions/890231…

Tested this on clearfog base, banana pi m64, banana pi m2+ ## Building and providing The elastic team doesn't provide deb packages for ARM devices. But together with docker, we're able to build the main executable for it. We will create a build directory which includes anything to install filebeat on a ARM device. So please stay inside the build directory the whole time you are using this tutorial. mkdir build && cd $_ ## Prepare source code First we will download, check and extract the source code of filebeat. Source: https://www.elastic.co/downloads/past-releases/filebeat-7-6-2 wget https://artifacts.elastic.co/dow…

Panfrost instructions Armbian !!!! I made a script that does all this, check a few posts later for the script !!!!! This tutorial explains how to build an Armbian image with panfrost. And what else you need to make it work. These are early drivers. Many things don't work yet. Only OpenGL 2.1 works now. You need to build an image with kernel 5.2 or later. For this you need an x86 pc with Ubuntu 18.04 or a virtual Ubuntu 18.04 x86 image. First install git, then clone the build folder from Armbian, and enter the build directory. apt-get -y -qq install git git clone --depth 1 https://github.com/armbian/build cd bu…

Building Armbian using Ubuntu (jammy) in a systemd-nspawn container https://gist.github.com/ag88/05245121cce37cb8f029424a20752e35 Special thanks goes to @Gunjan Gupta for the tip on PREFER_DOCKER=no

Canon provides source code for cups driver, but with some proprietary binary libs. This libs available only for x86. No way for direct compiling cnijfilter for ARM (and other architectures). But we have qemu! We can transparently run x86 executables on any other host architectures. Easy steps to run cnijfilter on ARM (or any other arch): - Build https://github.com/endlessm/cnijfilter-common for x86 - Copy all needed x86 libs using recursive ldd. And copy it to /usr/lib/bjlib/ - Patch all executables: set interpreter to /usr/lib/bjlib/x86/ld-linux.so.2 and rpath to /usr/lib/bjlib/ - Install these patched packages to ARM system…

I own a few Android TV boxes that have poor thermal designs that are prone to overheating when under sustained load. This can either cause your device to significantly slow down or shut down entirely. This can be fixed by cutting a hole in the bottom on your TV box above the SoC and sticking a small USB fan on it. In my case I am using a AC Infinity 40mm x 20mm USB Fan that cost me £10. CH340-fan-control is a python script to only activate my TV boxes USB fan when required by using a USB relay module. I'd expect somebody (or several somebodies) have already wrote a similar script for the same device but I failed to find it so here is my effort at fixing this c…

You may have seen discussions around the forum regarding work being done by @adafruit using circuit python with Armbian, but I wanted to make sure this nice write-up had proper visibility. https://learn.adafruit.com/circuitpython-on-orangepi-linux/initial-setup

Hi there, this very short tutorial is a solution when you need to backup/clone/save as small *.img file as possible of your whole fully bootable system (e.g. you have 8GB card but you want to make smaller system image for 2GB card). And another reason why I created this tutorial - I need to burn the same image to many microsd cards. I am using Windows (yup, hate me know) and Debian in these steps: Put your microsd card to Windows machine and make image of card with Win32diskimager. If your card is e.g. 8GB, you get *.img file with the same size (my name backup.img). Now in linux maxine (in my case Debian virtual machine) we are going to work with…

Hello, I don't know where to start, but I am looking to use Velleman VM140 USB IO-board with Armbian Linux. I tried first on NanoPi R1 that I have succesfully installed Armbian Linux. Linux I have installed is Armbian Buster for NanoPi R1. root@nanopi-r1:/etc# uname -r 5.7.15-sunxi I read somewhere there is kernel support for K8061 (the usb chip on the board if I understood correctly, looks to be a pic with USB). dmesg after attaching USB cable to R1: [960949.202099] usb 6-1: new full-speed USB device number 2 using ohci-platform [960949.435136] usb 6-1: New USB device found, idVendor=10cf, idProduct=8061, bcdDevice= 0.00 …

Hi all. I've made a new video where I compare the above boards. I show specs, performance and transfer speeds of everything. Here's the video. Here my gathered data. Benchmarks ---------- Khadas VIM3 | Clock S/C | B/C | Blender | 7z S/C | 7Z B/C | glxgears | CPUMiner | SBCBench | glmark2 Ubuntu Bionic 1.80Ghz 2.21Ghz 13m22s 1582 2322 192FPS 12.90 http://ix.io/1P6F Ubuntu XFCE 1.80Ghz 2.21Ghz 12m43s 1586 2316 355FPS 12.90 http://ix.io/1PhE Armbian Bionic 1.80Ghz 2.11Ghz 11m48s 1610 2244 …

If you want to do a complete headless install of Armbian OS on an Orange Pi 5, and connect with Windows Remote Desktop, I put together what has worked for me. I pieced this tutorial together using an Orange Pi 5, installing Armbian 23.02 Jammy Gnome Desktop, and connecting via a Windows 11 PC using Windows Remote Desktop client. Keep in mind, your Orange Pi OS needs to be a full Desktop edition, otherwise, if you're using CLI editions, you will not have a Graphical User Interface installed, which Windows Remote Desktop needs to connect. ArmbianOS Download Link Putty Download Link Start PUTTY and enter your Orange Pi's IP address or host name (orangepi5) …

MPD as installed by Armbian needs this audio_output configuration in /etc/mpd.conf in order to use the volume control of the on-board sound with Armbian mainline kernel 5.x on the BananaPi M1 (and maybe other A20 boards): audio_output { type "alsa" name "BananaPi BuiltIn" device "hw:0,0" mixer_type "hardware" mixer_device "default" mixer_control "Power Amplifier" }

Hi All, After I accomplished my IR Red Key Rick Rolling experiment the other day with much success, and from general end-luser use with Armbian, there were two things which irritated me, which are namely due to the default ALSA configuration that comes with stock Debian and that Armbian inherits. These were: Update: 11 September 2017. This guide will not work for newer Armbiam (Debian) installations which comes with Pulseaudio by default. If you really want what this tutorial provides, you will need to uninstall pulseaudio first: sudo apt-get remove pulseaudio 1) You can't have simultaneous applications using an Audio device. So, how ab…

Note: Guide Updated May 2017, as I realise that /dev/input/event3 may not always be the IR receiver device on your armbian installation. Hi All, I recently bought an Orange PI PC and the best thing I ever did was install Armbian straight away (and donate). Now that I have a bit of spare time, I wanted to configure my Orange PI PC to do something ridiculous like play Rick Ashley 'Never going to give you up' upon pressing the 'red button' on some generic Chinese IR remote for an LED light strip I have in my living room. Thanks to Armbian, most of the pieces are in place (such as the SunXI IR package) with the distribution, you just need t…

Hello everyone, today I would like to show you how to compile CoovaChilli and Freeradius for a Wifi Hotspot with captive portal on an Orange Pi PC (or PC Plus). I'm writing this because I couldn't find anything related to this topic on the internet, so I wrote this not very detailed guide. wget https://raw.githubusercontent.com/ua3nbw/opihotspot/master/opihotspot_debian.sh chmod +x opihotspot_debian.sh ./opihotspot_debian.sh Russian version https://ua3nbw.ru/all/orangepi-coovachilli-and-freeradius-for-a-wifi-hotspot-with-capt/

You all know the problem: You have a spare SBC (with USB3) laying around catching dust, a spare SSD or other hard drive and for whatever reason some (terabyte?) space in whatever cloud on the planet and have no idea what to do with it. Well here is what I came up with to solve this struggle https://zuckerbude.org/cloud-nas-with-local-cache/

Dear Armbian community, although I'm using Armbian a lot, I never had to submit anything to this forum (fortunately, because it works so well :-)), On my PC I've experienced lags on heavy IO operations. After a short dig into available information, I found a useful Cloudflare article on Kernel queues together with dm-crypt. A good & short summary on possible actions for users can be found here: https://wiki.archlinux.org/index.php/Dm-crypt/Specialties#Disable_workqueue_for_increased_solid_state_drive_(SSD)_performance Enabling the no-read-workqueue & no-write-workqueue options helped a lot! …

Hi there. Trying to get SPIDEV working on my good old cubietruck aka cubieboard3 with an allwinner A20. Found some posts here and there dealing with A20 boards. But nothing of that did anything for me so far. Enabled it in armbian-config hardware settings and rebooted. No /dev/spi* at all. No mentioning of "spi" in dmesg. Step 1 gave a line "overlays=spi-spidev" in /boot/armbianEnv.txt. Read somewhere else that there should be another line "param_spidev_spi_bus=0", but that was not created by armbian-config. Added that ...bus=0 line myself and rebooted. Still no spi device and nothing in dmesg /proc/device-tree-model says "cubietec…

There is no official sdcard image but the attached script will create a image for the OrangePi Zero/R1. It uses daily generated files from Debian daily-images and considered testing/unstable. SDcard image creation: You will need basic Linux/Debian and dosfs utils. No su/root needed. Run the script to generate sdcard image for writing to sdcard. Optionally, if you want ssh network-console access, add preseed.cfg to same directory as script. See attached preseed.cfg and example-preseed.txt . Basic installation: Once the installer is started, it runs completely in RAM and no longer needs files from the sdcard. You can delete all partitio…

I was able to read a DHT22 on PA10 with my Orange Pi Prime using https://github.com/Jeremie-C/OrangePi.GPIO Minimal documentation provided in readme https://github.com/lanefu/DHT22-Python-library-Orange-PI

For those of you who're interested in running a CMS on Armbian I've a small tutorial how to get django CMS working. If you're not interested in the 'story' just want a step by step installation guide, scroll to the end of this post, there you find it. Story: Following their installation guide it fails during creation of a django project with 'djangocms -f -p . mysite'. The error looks something like: Spoiler Traceback (most recent call last): File "/home/opi/django/env/bin/djangocms", line 11, in <module> sys.exit(execute()) File "/home/opi/django/env/local/lib/python2.7/site-packages/djangocms_install er/main…

Hello everyone! Is there anyone who tried to run Docker on armbian? Ok, let's start from the beginning: I am from the Hypriot Team (we made Docker available on ARM) and recently saw some guys successfully playing with Docker on armbian. Meanwhile, we know, that our Docker runs at least on the Cubietrack and Lamobo R1/BananaPi R1 on top of armbian! This is awesome because, you know, IoT is coming, and Docker on ARM helps get a grip on many challenges induced by IoT. However, we were only able to support Docker on Raspberry Pis so far... Imagine if Docker would run on more than just a few ARM boards! Armbian seems an awesome platform to …

As a result of all the work that Armbian developers put into the upgrade to kernel 4.14 for the XU4 board family, now we can enjoy many new features. One of them is the access to the SoC video encoding capabilities. Emby Media Server can take advantage of the Exynos 5422 MFC video engine for transcoding. That means lower CPU usage, lower temperatures, and the possibility of encoding in real time higher resolutions or more simultaneous streams. In my tests, I've been able to transcode one HEVC 1080p and one 480p at the same time, or five 480p (though it will depend on the bitrate of the source material). However, the ffmpeg version shipped with offi…

On some devices (mostly headless) like Pine A64 LTS and other SBCs with Allwinner SoCs is Lima blacklisted by default or not supported by distribution. For getting Lima work, you need to use distribution, which have already Mesa with Lima support (Mesa 20.1+) (or compile latest Mesa from sources, but this is not included in this tutorial). At the moment of writing, it's Ubuntu Focal and Debian Bullseye. I personally prefer Debian more, so in my case, download Debian Bullseye image for your SBC and burn it into the board. After booting into your board, find file named /etc/modprobe.d/blacklist-NAMEOFYOURSBC.conf (for me it's blacklist-pinea64-lts.conf…

Hi all. I wrote a small guide on enabling pps-gpio by modifying the device tree. With a PPS signal it's possible to setup your board as a Stratum 1 time server for your local network or the NTP pool. I used this method on a Rock64 but it should be applicable on most board. PPS-GPIO on Rock64 with Armbian legacy (4.4.X) kernel Cheers.

TL;DR *Works* with a minor amendment to the DTS overlay pin reference. $ uname -a Linux nanopineo 5.10.13-sunxi #trunk SMP Mon Feb 8 21:56:43 CET 2021 armv7l armv7l armv7l GNU/Linux $ dmesg | grep Machine [ 0.000000] OF: fdt: Machine model: FriendlyARM NanoPi NEO # Baked current kernel. Configuration ... CIR module appears to NOT be enabled by default for NanoPI NEO. $ grep -iE "^CONFIG_IR_.*(CIR|SUN)" /boot/config-5.10.13-sunxi CONFIG_IR_GPIO_CIR=m CONFIG_IR_SUNXI=m # Connected Vishay TSOP4838 IR Receiver to 3V3 (via 100R, with C100nF to GND), GND, OUT -> PL11 # +----------+ # 1 --- OUT ---! /--\ ! # 2 --- GND ---! | | ! # 3 ---…

http://forum.odroid.com/viewtopic.php?f=138&t=20972

I was working on blog article for our site about usage of Armbian extensions and I would be glad if it could be useful for the community It is on https://github.com/pavlot-scriptec/scriptec-blog/blob/main/customize_armbian_image_using_extensions.md Also I have created extension to enable Waveshare 3.5 TFT displays for RPi (and maybe other platforms). Any feedback is wellcome

Finally I got my lcd (some of them) to work with armbian on mainline kernel (5.4) using device tree overlay. It should be working on 4.19 kernel too. I test mine on orange pi zero. The one I am able to get working is ili9341 and st7735 based lcd. I'll add more detail later but for now I'd like to get this out. edit 1 : Adding ssd1306 and nokia 5110 overlay to the repo device tree overlay

Full root filesystem encryption on an Armbian system (new, fully rewritten, replaces my earlier tutorial on this topic) MMGen (https://github.com/mmgen) This tutorial provides detailed, step-by-step instructions for setting up full root filesystem encryption on an Armbian system. The disk can be unlocked remotely via SSH or the serial console, permitting unattended bootup. An automated script that performs the same steps, saving you much time and effort, can be found at https://github.com/mmgen/mmgen-geek-tools Note that unlike my earlier tutorial all steps are performed within a running Armbian system. The…

Full root filesystem encryption on an Armbian/Orange Pi PC 2 system MMGen (https://github.com/mmgen) WARNING: This tutorial has been obsoleted by Full root filesystem encryption on an Armbian system. In addition, an automated script is available, which can be downloaded here or by cloning the following repository: git clone https://github.com/mmgen/mmgen-geek-tools This tutorial provides detailed, step-by-step instructions for setting up full root filesystem encryption on an Armbian/Orange Pi PC2 system. With minor changes, it can be adapted to other Armbian-supported boards. The disk is unlocked remotely via ssh, permitting unattended …

In general we seem to get a schematic with some pin labels, not always complete, and certainly inconsistent. (Some like FriendlyElec do an amazing job, Libre Computer provides some spreadsheets, etc) Since Armbian is as much about "making it better" as it is about "making it work", I thought a good project that a lot of people could participate in is a relatively unified GPIO reference: https://docs.google.com/spreadsheets/d/1dJq7MM1_zA5HtXywDMZ9HMKyPaNgGmkxnuz3wYuk4s8/edit?usp=sharing I don't know that a google sheet is the best system, but it serves to illustrate my idea. Provide a consistent format so there are few que…

overlay examples: GPIO keys Mainline Linux OrangePi gpio-keys.dts /dts-v1/; /plugin/; / { compatible = "allwinner,sun4i-a10", "allwinner,sun7i-a20", "allwinner,sun8i-h3", "allwinner,sun50i-a64", "allwinner,sun50i-h5"; fragment@0 { target = <&pio>; __overlay__ { gpio_keys: gpio_keys { pins = "PA7","PA8","PA9","PA10","PA21"; function = "gpio_in"; bias-pull-up; }; }; }; fragment@1 { target-path = "/"; __overlay__ { gpio-keys-user { compatible = "gpio-keys"; pinctrl-names = "default"; pinctrl-0 = <&gpio_keys>; g-keys_up { label = "GPIO KEY_UP"; linux,code = <103>; /* KEY_UP, …

Hello Everyone This is my first topic here. To help myself in the future I did a guide to adjust armbian configuration and settings. This guide contains topics like: Maintaining the board updated Adjusting personal settings (keyboard, timezone, locale) Setting the sound output (default sound output to HDMI) Disable the desktop environment Setting the numlock to "ON" at start up Dealing with 4k video resolution It was based on my experience dealing with Orangepi PC (H3), but many things could be reused to others boards. I hope this guide may be helpful: https://github.com/lbmendes/armbian-settings/b…

First of all, credits goes to https://4pda.ru/forum/lofiversion/index.php?t750921-2560.html Device that I used for this guide: https://www.aliexpress.com/item/3-5-Inch-TFT-LCD-Moudle-For-Raspberry-Pi-2-Model-B-RPI-B-raspberry-pi/32707058182.html Pinout: http://www.waveshare.com/3.5inch-rpi-lcd-a.htm (Yes, the device is a waveshare knockoff) How to place the device? For Orange pi lite/one it is reversed. For the rest, it should be normal. Refer to https://forum.armbian.com/index.php?/topic/724-quick-review-of-orange-pi-one/ for more info. There are two sections to this guide. Legacy / Mainline Legacy Kernel [You can …

TL;DR: All available H3 boards do not differ that much. But the few differences sometimes really matter! The following is an attempt to compare the different available H3 SBC that are supported by Armbian. The majority of boards is made by Xunlong but in the meantime two more vendors started cloning the Xunlong boards (and also Olimex is preparing H3 boards as OSHW). Both Foxconn/SinoVoip with their Banana Pi M2+ and FriendlyARM with their NanoPi M1 tried really hard to copy everything as exact as possible (the so called pin mappings -- how the many contacts the used H3 SoC is providing are routed to the outside). All the boards share the same 40 pi…

The following is a short overview what you can expect from small and big H3 devices when used as a NAS. I chose the least capable device (OPi Lite for $12: not even Ethernet and just 512MB DRAM) and the best possible (OPi Plus 2E for $35: GBit Ethernet, 3 USB host ports exposed that do not have to share bandwidth, 2GB DRAM). I wanted to test also a H3 device in between with 1GB DRAM but since results are somewhat predictable I dropped the whole idea (the performance bottleneck on all Fast Ethernet equipped devices will be network unless you add the $7.50 for an USB-Ethernet dongle -- see below -- and all other Gbit Ethernet capable H3 devices are not…

We included in Armbian a small utility called h3disp. If called without arguments it displays just a usage information: tk@orangepipc:~$ sudo h3disp [sudo] password for tk: Usage: h3disp [-h/-H] -m [video mode] [-d] [-c [0-2]] ############################################################################ This is a tool to set the display resolution of your Orange Pi by patching script.bin. In case you use an HDMI-to-DVI converter please use the -d switch. The resolution can be set using the -m switch. The following resolutions are currently supported: 480i use "-m 480i" or "-m 0" 576i use "-m 576i" or "-m 1" 480p use "-m 480p" or "-m 2" 576p …

I came across this, the project allows the control of a lot of home-brew hardware as well as commercial products: https://www.home-assistant.io/docs/installation/armbian/

Hi, There's been a few guides around on how to get RDP working with Armbian so you can login from your Windows or other PC. Some solutions mentioned in various threads here were: Install tightvncserver instead + x2go bloat (i.e. use VNC) Only login as root - didn't seem to make any difference for me Change some permissions of a log file in your home directory. Well, this is what I did on my Orange PI PC running Buster desktop with Kernel 5.4, as of April 2020. sudo apt install xrdp xorgxrdp sudo systemctl enable xrdp sudo reboot ... and that was it. The missing piece of the puzzel appeared to be the install of …

Hello, I apologize in advance if I haven't put the topic in the right section. I want to share my experience with NanoPC-T6 and two NVMe m.2 disk. I use my NanoPC-T6 for a small server. In the beginning I had 2 SSDs and an M.2 to 2 SATA adapter. But I never found the right solution to power both the NanoPC-T6 and the SSDs from 1 place. After some internet searching I was able to find a solution on how to put 2 NVMe drives on my NanoPC-T6 As you know NanoPC-T6 has 1 M.2 M-Key connector with PCIe 3.0 x4 There is also one PCIe which is M.2 E-key connector with PCIe 2.1 x1 With this adapter: https://www.aliexpress.com/item/1005004762…

Hi all. I've made a new video on how to share your mouse and keyboard between multiple SBCs with Armbian. This is the source website where I've gotten my info. There is a lot more info to be found on it then I show in the video. https://itsfoss.com/keyboard-mouse-sharing-between-computers/ Here is my video. Install Barrier sudo apt install snap snapd sudo snap install --edge barrier Run Barrier /snap/bin/barrier Greetings, NicoD

Hi all, Maybe there are a lot people who got this working but for me was today the day. I buyed a time a go a cheap but fast NVME SSD from Aliexpress. The smallest one a 128GB. I have also a 512GB in my laptop and for the price they are really good. But i needed also a USB-NVME external housing. That is the Ugreen NVME 10GBps to USB adapter. In very short but i will explain more in the future. 1. Flash a MicroSD card with your favourite Armbian to the MicroSD. Update with sudo apt-get update. Also with a SSH session not a problem. 2. Place the USB disk in a USB 3.0 port of the Orange Pi. By the OrangePi 4 it´s the blue one on the…

If you use a SIP Voip client on your phone or computer, you can use the sip protocol and scripting to monitor your Armbian board. I'm using Ubuntu Xenial, but other versions should work as well. I have the Linphone client on my phone and I use the free Linphone SIP service. Linphone.org hosts a free SIP service that allows users to make audio or video calls using SIP addresses via the domain sip.linphone.org. You can also send text messages. SIP requires an internet data connection, and my phone is connected via WIFI most of the time except when I'm commuting, so I set up my monitoring chron jobs on the Armbian device to run at times when…

Hi, To enable the armbianmonitor to show information on the running system on the serial console, I used to have a custom startup script, called from /etc/rc.local. After some time, I thought it was more neat to have this automatically started (and stopped) for login sessions that are started on serial consoles/terminals. This lead (led?) me to the following systemd unit file: [Unit] Description=armbianmonitor on ttyS2 Requires=serial-getty@ttyS2.service After=serial-getty@ttyS2.service After=getty.target BindsTo=serial-getty@ttyS2.service [Service] Type=idle ExecStartPre=-/bin/sleep 10 ExecStart=/usr/bin/armbianmonitor -m TTYPath=/dev/ttyS2 Standa…

tkaiser has built a new Kernel with i2s Modules. With this Kernel and some cheap DAC e.g. (http://www.ebay.de/itm/Audiophonics-I2S-DAC-ES9023-Sabre-to-Analog-24bit-192KHZ-fur-Raspberry-PI-/291573327639?hash=item43e31fe717:g:TTwAAOSw~OdVZXtm) it is possible to get good quality sound out of the Orange Pis. After installing the Kernel Two Things have to be changed in the fex File: Change Directory to boot: cd /boot Turn the script.bin to a fex-File and open it in an Editor sudo bin2fex script.bin script.fex sudo nano script.fex Now change the following Entries: [twi1] twi_used = 1 to [twi1] twi_used = 0 and [pcm0] daudi…

I am releasing this patch in the hope of you may find it useful. I have also included a sample dts file. It seems to work in 48mhz quite well with very few SPI errors. (Note that the pieces of the driver has been around for some time but I have never seen it put together without further work. Hopefully this patch would make it readily usable. I have tested it on 5.5.18 and quite happy with it.) 0001-fbtft-fb_ili9488.patch 1_ili9488.dts Sample file is for nanopi neo. Driver also works with 4 inch LCD, MSP4020, MSP4021

https://www.openhab.org/docs/installation/armbian.html

this is posted to Gist: https://gist.github.com/ag88/65db5434158683e43d1cc77c337ebdb5 Introduction Rpi-monitor https://github.com/XavierBerger/RPi-Monitor is a very nice app for monitoring sbc (single board computers/ actually bigger computers as well) like RPi on a web. it gives you a quick look at various system metrics cpu load, uptime, temperatures etc and more on a nice web page. and on top, makes nice time series graphs for the same, practically a dashboard. Installing in Armbian 25.8 for Orange Pi Zero 3 Rpi-monitor is normally not found in the common Apt repositories and actually the binary is a little old. I tried…

Required materials ESP32 KOB electronic lock Relay STONE STWI070WT-01 display MFRC522 module Realized function 1. card registration. 2. username and password registration. 3. card swipe to unlock the electronic lock. 4. User name and password to unlock the electronic lock. Connection diagram GUI design Code sharing import mfrc522 import time import _thread from os import uname from machine import Pin, UART #from pyb import UART #import machine suos = Pin(32,Pin.OUT) uart2 = UART(2, baudrate=115200, rx=16,tx=17,timeout=10) ESP32_HSPI_CLOCK = 14 …

For those of you who are interested in using a OPI zero as a small IoT-Server. I have some hints to get it working. It's more or less a lmgtfy How To plus some arduino code to test if it works. Hardware: OrangePi 0 with Armbian 5.25 connected over lan to my router DHT11 Module on a Wemos D1 mini (a small cheap wlan MCU for ~3$ which can be programmed via the Arduino IDE) Installation: First of all we install node-red on the OPI. Instead of rewrite how to do that again I just give you the link who to do that: Node-Red on armbian Second we install Mosquitto as a mqtt broker. If I have it right in mind I followed this instructable (I'm not shure…

Hello, I'm new here and do not quite understand the sub-forums here but hopefully this is the right one. I got an Orange pi ONE running 4.19 RT kernel with Armbian buster. I was testing out the GPIO capabilities of the H3 SoC without any libraries and got only 1.67 Mhz at best(which is ironically the same as WiringPIOP) with some task interrupt issues. #define INP_GPIO(g) *(unsigned int *)(gpio+0x04) &= ~(7 << (((g) % 10) * 3)) //I did not thoroughly check if the mapping is okay #define OUT_GPIO(g){\ *(unsigned int *)(gpio+0x04) &= ~(6 << (((g) % 8) * 4));\ *(unsigned int *)(gpio+0x0…

Java UIO provides high performance Java interfaces for Linux Userspace IO. Java UIO was built from the ground up to use modern kernel APIs, libraries and code generation techniques to provide a best of breed cross platform approach. It does not make sense to recreate the wheel like so many other IO libraries. JDK 17 LTS is supported out of the box. I've been committing code to U8g2 that utilizes the same userspace code at the C level and dramatically improved the performance of HW/SW SPI and I2C in the arm-linux port. I also made the arm-linux port thread safe and multi display capable (you can use this in C as well obviously). It made sense to add modularizat…

UPDATE 11-FEB-2017: Version 2.2.0 is released: now including video recording in stead of only images and also a privacy option to black out areas that may not be filmed. UPDATE 09-FEB-2017: Version 2.2.1 is released: memory leak(s) fixed and in some cases video stopped recording. This should be fixed now. Download via this page. Kerberos.io (link) is a relative new video surveillance program focusing mainly on the Raspberry Pi. In collaboration with the owner of the github project I managed to get it working on my Orange Pi Plus and PCDuino3 nano using Armbian (Debian Jessie) and a Logitech UVC compatible USB webcam. It consists of 2 modules: the Machiner…

I pushed a template for the NanoPi NEO (2/Air/Core/Plus2) onto my github: https://github.com/Tonymac32/kicad-templates If you want to make add-ons, that's fully labelled and the header positions are as correct as I could get them without official reference. I have made a few boards with it, so can vouch that it will assemble. I'll add more as I have time and money to do so, since I don't want to push any that aren't verified in some manner.

Hello reader I will report here about my experience to watch Netflix as written in the title. To do so, I got a current LE image from @balbes150 (thank you). You may be asking the same question as I do (did), why using the image from balbes and not the official one from the download page ? It is actually quite simple, balbes integrates the latest Kernel for his LE builds. While on a x86 system the kernel isn't so interesting, it is on ARM systems, because a lot of the development happens 1 or 2 year later of the release of the SoC. I have asked him about the different versions he offers for Le Potato: All versions…

I know the RPi is pretty limited on the GPIO pins. Now my question is how it looks on Le Potato, i.E. is it possible to power a fan directly from the GPIO pins? Powering it from the 3.3 V line seems to work just fine but I fear damaging hardware by trying to connect it to a GPIO instead.

Hello everybody. I am trying to build an DIY headset from scratch and I originally planning to use some armbian OS for its SBC at its heart of the device (like an orange pi, or something maybe a bit stronger who knows - I happily accept recommendations). For the headset it is necessary to have proper opengl support with hardware rendering capabilities and also good to have video acceleration maybe so I think the legacy kernel fits the purpose best. PROBLEM: I tried to plug in the HDMI display - it does not work. Details: The display is seemingly not working when attached to the HDMI port. I see some led flashing so I think s…

Hello! Recently, Armbian Debian 10 was installed on my ODROID-C2 I can't configure lircd, but it worked on Odrobian Debian 9! Please, explain how they configure LIRC to 4.19 now without /dev/lirc*? WBR, WRA-RIPE

For now there's one downloadable Armbian Buster image for the M4V2 from pask. Also the patch needed to prepare your own image : https://drive.google.com/open?id=1LaJIywiZnZUkLDZ9HkWrRtc0PyfiYGOL Yon build or download any other M4 image and apply the patch from pask For wifi use this patch from MartinAyotte Download both files https://forum.armbian.com/applications/core/interface/file/attachment.php?id=5386 https://forum.armbian.com/applications/core/interface/file/attachment.php?id=5387 Copy these to /lib/firmware/brcm/ Reboot. That's it. Official Armbian for M4V2 comming soon.

Let's start with a weird image first: In the plastic box is an Olimex A20-Lime2, a 2.5" HDD with 2TB and Olimex' largest battery with 6600mAh. Mounted on the top cover (box standing on the side) is a Banana Pi M2+ (to be replaced with NanoPi M1 or OPi One/PC in the future) Why Lime2? Since this board from our friends at Olimex is designed intelligently and provides DC-DC step-up converters on the board providing the ability to power also the connected SATA disk when running from battery (unlike most other A10/A20 boards that do only provide 5V on USB ports in battery mode but not to the disk!). And since A20 is perfectly supported by ma…

Clearfog PRO with Linux 4.12.4-mvebu Samsung 840 PRO utilization: iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 random random kB reclen write rewrite read reread read write 102400 4 62501 101691 98761 94430 34522 93050 102400 16 183325 215091 231439 232948 101667 171875 102400 512 301985 307789 341261 344567 328849 309560 102400 1024 294818 309177 345099 347791 339763 309775 102400 16384 271066 344426 384226 …

hi all, as documented here, i did some minor experiments with small heatsinks on an orange pi one sbc (allwinner H3) among the things i used a small matrix multiplication program which multiplies a 1000x1000 matrix single precision floating point matrix main.cpp the command to build is c++ -O2 -std=gnu++11 -pthread -o mat main.cpp then run ./mat the last documented results on an orange pi one H3 running at 1.2ghz is 2389.49Mflops ~ 2.39Gflops the sources attached is 'optimised', the means of optimization is unrolling of the innermost loop to take advantage of platforms that could do quad sp fp simultaneous execute …

boa tarde, meu e Alfredo, comprei uma placa MMDVM para montar um hotspot, mas nao consigo encontrar compatiblidade , pois estou usando ARMBIAN OS alguem pode me ajudar.

I have orange pi pc with debian. Orange Pi is connected via mobile connection (Wifi AP). Every day I lose more than 500mb data to nothing. What I must disable to normal operations without any update?

What shall moderators do on our forum. Basics: - job should be invisible - spam control and clean up (rare) - approve posts from new users (daily) - Warning: editing topic tittle change it's URL - move topic to appropriate forum (rare) (tick "Leave a link to the new location" - it deletes auto in 30 days) recognise and tag tutorials & researches. Move them into "Research Guides & Tutorials" - merge, pin and lock topics (rare, with caution) - cut and move posts to new topics (rare, with caution) Intermediate: - Warn User for: spamming, inappropriate language, signature v…

There have been several disjointed tutorials on making a raspberrypi or orangepi into a surveillance camera. So I threw this together to maybe help someone out there with any issues. I used the orangepipc+ but any orangepi board should work as long as it has the basics, internet connectivity, storage, and a camera. (I highly suggest heatsinks as well) any feedback or enhancements to this tutorial are greatly appreciated. ------------------------------------------------------------------ ORANGEPI IPCAMERA ------------------------------------------------------------------ su root apt-get update apt-get upgrade apt-get install …

Some of the boards supported by Armbian have an mpcie slot. The only one that I know of that also has a sim slot is the celarfog pro. (Correct me if I missed something) I found this little add on board that supposedly adds a sim card to an mpcie modem. Think it might work on some or which of the boards? I looked at this but I get lost in figuring out how to form the udev rules. Anyone get 4g going on Armbian on any board in the US?