Allwinner sunxi

I have a problem with my wireguard implementation. When connected through it I get lag spikes every few seconds. What might be the cause and solution to this? It is not the internet connection/cable/etc because a raspberry pi running wireguard works fine on the same exact cable, port etc.

hello, my orangepi3 after the updates of firmware of these days seems to loose eth0, at reboot take eth0 and eth0:avahi with class 169 ip. i made backups (i use a sd to restore the mmc mouting hd and then copy the gzip image) so i have not problems to restore but, i suspect, the previus version is working but the new one not. sorry for my worst english... ab

I made an application with opengles which works correctly in armbian xenial 3.4.113, I always have 40 or 50 fps, also if I run the es2gears program it gives me a constant 300 fps, I wanted to change to a more current kernel and download armbian buster, but here my program runs at 5 or 6 fps, and es2gears does not exceed 30 fps. I was reading the posts on the subject in the forums and I found that installing the lima driver activated 3d acceleration, but I could not make it work. Some information that can help me activate 3d acceleration with kernel 5.8 I am using an orange pi one thanks: D

Hello I`m download newest version Armbian desktop for my Orange Pi. Install the following packages sudo apt-get install tightvncserver sudo apt-get install xrdp But I have error when I want connect to desktop from my Windows 7 Additional I try to connect use VNC Viewer but resulution is small and visual desktop is other the wwhen I`m normally attach HDMI monitor to OPI.

Orange Pi Zero 512 MB has a serious wifi problem. After i connect the wifi network, i loose connection and i can't access my zero until i connect with ethernet cable. Interestingly, after i connect ethernet cable, wifi reconnects. i set up my wifi connection with nmtui. Auto connect enabled. I really need to solve this wifi issue. In my thinking there two options, which one is better i don't know. 1 st option: I have to buy wifi adaptor, but i don't know will it solve the problem. (and probably i am going to have driver problem) 2nd option: I am going to write a new thread with python. This code will check wifi connection every 10 seconds, if …

Hello, First of all, I'm new on Armbian I got some a stack dump on the console and can see following messages on kernel.log : --- Oct 24 14:27:28 localhost kernel: [183195.142242] 8<--- cut here --- Oct 24 14:27:28 localhost kernel: [183195.152222] Unable to handle kernel paging request at virtual address 2f68f25c Oct 24 14:27:28 localhost kernel: [183195.167942] pgd = 36f6b267 Oct 24 14:27:28 localhost kernel: [183195.179169] [2f68f25c] *pgd=00000000 Oct 24 14:27:28 localhost kernel: [183195.191263] Internal error: Oops: 805 [#1] SMP THUMB2 Oct 24 14:27:29 localhost kernel: [183195.204864] Modules linked in: brcmfmac brcmut…

Hello, I have a cubitruck With armbian and it runs the most time fine. Now i'm Not AT Home and the cubi is Out, I See in my router That He is Not running. I Can't connect over ssh. Who can I Look after a reboot when i'm AT Home what is the problem for going down. Thank you

Hi there, I want to migrate system on OPi PC+ from 32GB uSD card to 16GB card. System is small enough to fit on 16GB, but too large for 8GB eMMC (amazingly fast according dd). How to do it? My idea is: - copy (raw, using dd) first 8192 sectors from 32GB to 16GB, - then remove partition (32GB) and recreate it with 16GB size, format using same EXT filesystem, - copy (on another computer, or "simple" Armbian installed on eMMC) partition contents using rsync. Will it work? Will there be no issue with different UUID of new partition?

OK, being away for a while and having 5.x kernel and sunxi_cedrus around I need some directions. I had some embedded 3.x desktop installations in a community museum showing videos (using mpv after a button press) which need revising. So I decided to update the firmware/scripts etc. These are Orange Pi One's... In the past I installed 3.x desktop version as it has better video acceleration. What should I do now? I don't see a focal desktop in downloads. Is it OK to use the focal server, install xfce4 on top of it? Will I have video acceleration? I've been using HEVC .mkv files... Thanks in advance Bülent ~# uname -a Linux myhostna…

I need some help with using pwm on my orangepi3, i installed wiring pi and turned on leds, but i don't know what pins are pwm capacble nor don't i know how to use pwm, i also want to add an ir remote to then change modes of led strip, can somebody help me with that or will it be easier to just use a microcontroller since i have a lot of experience with programming them but almost no with orangepi3 help would be greatly appreciated soft pwmlibrary? also installed ir support, but can i get data from the ir sensor with wiring pi?

I know it's not an officially supported board, but it's been working really well so far, so I'll give it a shot. Today I updated my kernel to 5.9.0-sunxi (coming from 5.9.0-rc7-sunxi) and after rebooting the (wired) network was dead. Everything looked fine, ethernet driver is loaded, interfaces were up and had IP addresses, but packets were not being sent. Pinging anything but the Banana Pi itself says "destination host unreachable". Routes were set and looked correct - even tho they should not even be necessary as I was pinging the gateway. tcpdump on eth0 showed nothing at all, almost as if the kernel doesn't know where to send the packets. Anyon…

Hi, I've been trying to get the next IMU sensor to work: Fusion_IMU_BNO055, on my OPi zero with Armbian Bionic 20.08.10 with the linux kernel 5.8.14-sunxi. I have installed everything from the official Adafruit guide but I still get the same error. I have followed all the steps of this guide for beginners: OPi_r1_guide, executing all the commands successfully. However, I still have the same error in Python that is related to the "board" module. root@orangepizero:/home/Test# python Python 3.6.9 (default, Oct 8 2020, 12:12:24) [GCC 8.4.0] on linux Type "help", "copyright", "credits" or "license" for more information. >>> import board Trac…

Hello, I have a design with old but cheap Allwinner A20 processor. At the boot time, u-boot keeps rebooting just after reaching the below line (just after DRAM: 1GiB): U-Boot SPL 2019.07 (Oct 13 2020 - 17:36:08 +0300) DRAM: 1024 MiB CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 Trying to boot from MMC1 U-Boot 2019.07 (Oct 13 2020 - 17:36:08 +0300) Allwinner Technology CPU: Allwinner A20 (SUN7I) Model: Olimex A20-OLinuXino-LIME2-eMMC I2C: ready DRAM: 1 GiB I even tried ready images from internet, alghtough some did not reboot countinlusly, but they stuck at the same place (line: DRAM: 1 GiB). BTW, in our PCB, we did not use …

Greetings, Some time ago, I built armbian with kernel 5.4.51. I applied a patch to two dts files that allowed for the OV5640 camera to work. By "work", I mean /dev/video0 was present in the system and /dev/media0 was also present. I could set camera parameters with media-ctl pointing to /dev/media0. Now, I've updated, and using a legacy kernel, 5.4.65, I cannot reproduce this. I've applied the same dts changes, but upon booting this image /dev/media0 is missing. I've compared the two kernel configurations, and there are very minimal differences: # diff config-5.4.51-sunxi /boot/config-5.4.65-sunxi 3c3 < # Linux/arm 5.4…

Dear community, i've installed on my orangepi win plus the last armbian focal, and pulseaudio configuration tab don't gave me the possibility to choice output sound over hdmi to my tv screen . It seem as that no driver installed. Thanks for your help

Environment: (H2+) + linux-sunxi + ov5640 It can be registered by kernel ,but I can't capture any picture from camera . Here is my kernel demsg: ===================================================================================== # dmesg |grep VFE [ 1.720292] [VFE]cci probe start cci_sel = 0! [ 1.720328] [VFE]cci probe end cci_sel = 0! [ 1.720359] [VFE]cci_init end [ 1.720372] [VFE]Welcome to Video Front End driver [ 1.720514] [VFE_DEBUG]vfe_probe [ 1.720638] [VFE]pdev->id = 0 [ 1.720644] [VFE]dev->mipi_sel = 0 [ 1.720650] [VFE]dev->vip_sel = 0 [ 1.720655] [VFE]dev->isp_sel = 0 …

Hi everyone! I'm looking for an old image of Cubieboard with legacy kernel 3.4 . Someone can help me? I've searched into main site and forum but can't find anything. Thanks

I had build armbian 3 days ago, kernel ="5.8.13", with NanopiNEO, I want use a TFT screen, type is ILI9341, when I use "armbian-config" open spi_spidev, no /dev/spi* created, and screen does not work. here is config: # # cat /etc/modprobe.d/fbtft.conf options fbtft options fb_ili9341 name=fb_ili9341 gpios=rest:0,cs:67,dc:2,led:3 speed=48000000 fps=26 rotate=90 bgr=1 txbuflen=65536 debug=3 here is armbian-hardware-monitor.log Other: ttyS0 can't login, Does somebody can help me, thinks very much! armbian-hardware-monitor.log

Hi guys, I searched for an answer but couldn't find a working one. Most answers from 2017 and it's not possible to answer there. Could someone please explain how to use the wifi and bluetooth module on Armbian 20.08.7 Bionic with Linux 5.8.13-sunxi (minimal without desktop)? ____ ____ _ __ __ ____ | __ )| _ \(_) | \/ |___ \ _ | _ \| |_) | | | |\/| | __) || |_ | |_) | __/| | | | | |/ __/_ _| |____/|_| |_| |_| |_|_____||_| Welcome to Armbian 20.08.7 Bionic with Linux 5.8.13-sunxi System load: 2% Up time: 35 min Memory usage: 8% of 998M IP:…

Hi, root@orangepilite:~# armbianmonitor -u System diagnosis information will now be uploaded to Please post the URL in the forum where you've been asked for. I'm trying to connect my PI board to my smartphone's phone hotspot. I tried with different phones (ASUS Zenfon, Huawei P10, iPhone 11) - "nmcli dev wifi" does not display my hotspots, however nearby computers and the phones themselves do see the hotspots. The PI finds many wifi networks around and use one of them w/o issues: root@orangepilite:~# nmcli dev wifi IN-USE SSID MODE CHAN RATE SIGNAL BARS SECURITY * fbk.info Infra 6 270 Mbit/…

Ran the following command on my Banana PI to move to the HDD (SATA) nand-sata-install Install was a success: However I think some stuff went wrong during the transfer. Whenever I open a file in nano I get the following error: Error in /etc/nanorc on line 260: Error expanding /usr/share/nano/*.nanorc: Inappropriate ioctl for device I cannot run apt-get update anymore: pi@bananapi:~$ sudo apt-get update && sudo apt-get upgrade Hit:1 http://security.debian.org buster/updates InRelease Hit:2 http://deb.debian.org/debian buster InRelease Hit:3 http://deb.debian.org/debian buster-updates InRelease Hit:…

Hi community To use Kubernetes (K3s) on my Orange Pi 3 I need to enable cgroups. I running currently on Armbian Buster (20.08.1) As I understand this needs to be enabled on build-time (?) or is there any other way to enable cgroups? Is there any other image which has cgroups enabled? any support is appreciated many thanks Daniel

I am having problems with ethernet, the sbc was connected to 100 mbps network and it worked normally, but recently i relocated it and connected it to another cable, the problem is that now i only get 10mbps, the cable is ok because it tried in my pc and got 100mbps, but i only get 10mbps on the sbc, then i found how to fix this in settings, but i acidentally removed ethernet connection that i was using and now the ethernet doesn't work, do i have to change something in network interfaces? also it says no link detected

Hello, I have a GPIO pin that is high when starting the board. I am trying to force it low. Taking a look at gpio readall +-----+-----+---------+------+---+---Pi ?---+---+------+---------+-----+-----+ | BCM | wPi | Name | Mode | V | Physical | V | Mode | Name | wPi | BCM | +-----+-----+---------+------+---+----++----+---+------+---------+-----+-----+ | | | 3.3v | | | 1 || 2 | | | 5v | | | | 12 | 8 | SDA.1 | ALT5 | 0 | 3 || 4 | | | 5v | | | | 11 | 9 | SCL.1 | ALT5 | 0 | 5 || 6 | | | 0v | | | | 6 | 7 | GPIO. 7 | ALT3 | 0 | 7 || 8 …

Device: Orange Pi PC. Image: Armbian_20.08.1_Orangepipc_focal_current_5.8.5.img. Issue: No sound in the terminal when I run `sudo speaker-test` or `speaker-test` or if I launch kodi-gbm. I have an old Armbian image with Linux 3.4.112-sun8i Ubuntu 16.04.7 Xenial, it has xfce desktop installed -- there if I set sndhdmi device as a fallback device then `speaker-test` plays fine. I tried installing xfce and pulseaudio on this current Armbian Focal (not via arm-config, but via `apt install xorg xfce4 pulseaudio`) but in the audio settings there are only 2 devices both named "Built-in Audio Stereo" and setting any of them as a fallback doesn't pr…

hi everyone, I'm running latest Armbian 20.08.1 Buster with Linux 5.8.5-sunxi on a Nanopi Neo Core. I cannot understand why I cant turn GPIOA0 on\off, can't configure it as output. I have no problem with any other GPIOs, just this one. command i'm using: gpio mode 0 output gpio write 0 1 I managed to make the GPIO as Output using this command, but still no go - the output cannot be set. echo 0 > /sys/class/gpio/export echo out > '/sys/class/gpio/gpio0/direction' dmesg don't show any errors. I checked H3 documents, there's no conflict in the mux with other GPIOs, and just to be sure i turned UART every…

Hello ! I have a problem with an OrangePi Zero under Armbian Buster with mainline kernel (5.8). I need to put the module snd-aloop as primary soundcard (index=0), and the integrated soundcard sun4i-codec as index=1. It worked very well with kernel 5.4 and before. I just had to load the snd-aloop module by adding it to /etc/modules and add "options snd-aloop index=0" to /etc/modprobe.d/alsa.conf. But now this is impossible, snd-aloop doesn't load. I had this message when I try to load it manually : modprobe: ERROR: could not insert 'snd_aloop': No such device After reading configuration file of the kernel, I saw that the module sun4i-codec (integrat…

Dear All, I have been downloaded the Armbian Buster OS from "https://www.armbian.com/orange-pi-3/" link and flash on Orange pi3 board. We are tesing OPI3 board with TCL monitor [(Model : 55P8E) (Resolution: Ultra HD (4K) ) 55 inch ] but getting the blank screen on display. After that we changed the TCL monitor setting by HDMI 2.0 "OFF" from "Auto" mode then it's working fine. We have another monitor which does not have HDMI 2.0 OFF mode facility so we can't use our product in market due to this limitation. FYI : same thing we tested with fresh orangepi board (with default android image) and it working fine. It will be good if some…

Hi all, I've purchased a second hand banana pi M1 board with an BPI 7 inch LC connected on prarallel RGB. The board and the LCD is working with last bananian distribution and https://github.com/BPI-SINOVOIP/BPI-M1-M1Plus-Configuration/blob/master/fex/BPI_M1_7lcd.fex. I'm trying to make both working with Armbian but I'm lost. I don't find the script.bin, /boot/script.bin or anywhere. And no idea how to set /boot/armbianEnv.txt for the LCD. The kernel have been rebuilded using this topic. Any help will be apreciate. Regards Hugues

Is there a kernel package with PREEMPT-RT for OrangePi PC Plus? I'm trying to get linuxcnc running - which works, but without USB. I used this guide: https://orangecnc.gitlab.io/quick-start.html. Kernel there is 5.4.18, which has the USB-not-working-bug for Orange Pi Plus.

I bought an orange pi lite 2 and I would like to use it with the ADC MCP3008 but when executing the code in python using the spidev library, it always returns the value of 1023 and when I disconnect the ADC it keeps showing the same value, it is as if there was no communication , The ADC is not the one with the problem since I tried it with an arduino mega and it works perfectly, it is in the orange pi lite 2 where it does not work. the connections are: VDD=3.3V VREF=3.3V AGND=GND CLK= (PC00) SPIO_CLK DOUT=(PC03) MISO DINT=(PC02) MOSI CS = (PC05) SPI0_CS0 DGND= GND import spidev import time spi = spidev.SpiDe…

You need to connect the equipment via the I2C bus with a frequency of 1 kHz or 10 kHz to Orange pi 3 (OS Armbian Buster with Linux 5.3.9-sunxi64). Supported setting of these frequencies and how to change correctly? Recoded sun50i-h6-orangepi-3.dtb to dts: cd /boot/dtb/allwinner/ dtc -I dtb -O dts -o sun50i-h6-orangepi-3.dts ./sun50i-h6-orangepi-3.dtb nano ./sun50i-h6-orangepi-3.dts What should be done next to set the frequency of 1 kHz or 10 kHz to the i2c-0 bus? Thanks.

My device is nanopi neo plus2 h5 soc with armban Buster server installed. I have realtek rtl8812au mt7612u two wireless network cards. I found that armbain's wifi driver is relatively old, how do I compile the latest driver https://github.com/aircrack-ng/rtl8812au https://github.com/openwrt/mt76 I tried to download the latest rtl8812au driver and compile it, but an error occurred device FriendlyARM nanopi neo plus2 0S armbian PRETTY_NAME="Armbian 20.08.3 Buster" allwinnertech h5 chip kernel Linux nanopi 5.8.10-sunxi64 CC [M] /root/rtl8812au/hal/phydm/halrf/rtl8814a/halrf_iqk_8814a.o CC [M] /root/rtl8812au/hal/phydm/rtl8814a/phy…

Dear maintainers, I have my sensors configured to reboot every night via a user cronjob (0 0 * * * /sbin/reboot), 14 sensors do this without a problem. I've fixed the nanopi neo+2 reboot from NAND some months ago (by re-using friendlyarm first stage u-boot). I just stumbled upon a failed reboot with one of my nanopi neo+2 nodes, after two successful reboots. Looking at the /var/log.hdd/syslog, it got stuck in the shutdown procedure when the watchdog reported a failure. The /var/log.hdd/syslog.1 extracts below show the start of the watchdog, and the stop of the watchdog and its failure. After the failure the system doesn't come up anymore, it needed a pow…

Hi. I'm using "Orangepi-r1_focal_current_5.8.5" Armbian. I'm connected to it via Wifi. Everything working fine, but after few hours, I notice that it is no longer showing on my network. If I connect by cable I can ssh to it via ethernet without any issue and it stays available for several days without disconnecting. Any idea why this happens? when Wifi disconnects I will have to reboot to show it again. And I am not running any program on it. Is orange pi r1 wifi like orange pi zero wifi suffering from poor software support?

Heya, Configuration :: Friendlyarm NanoPi Neo (Allwinner H3) Matrix TFT2.8 (https://www.friendlyarm.com/index.php?route=product/product&product_id=102) Armbian Release: Bionic 5.8.y found here: https://www.armbian.com/nanopi-neo/ I have this st7789v-based display working on spi0.0 by utilising a custom overlay tft28.dts as below, but I cannot get the ads7846 touchscreen controller to use an additional gpio chip select (ie: spi0.1) because the ads7846 driver seems to be holding that additional cs line in a 'logic 0' state at zero volts. I believe the hardware is not at fault because it works correctly using the Friendl…

I installed the image Armbian_20.08.1_Orangepiplus2e_focal_current_5.8.5_desktop.img on my Orange PI Plus 2E and I installed RetroArch to setup a retro gaming board. Everything installed ok but all games even weak games like for Super Nintendo, are running slow and no audio, does anyone here already tried to get RetroArch working on this board? Audio is not working , it uses pulseaudio and it's installed already. I already tested RetrOrange Pi image, it uses Armbian too I guess, most of the games runs at full speed, the reason I am not using is that is a little outdated, some emulators doesn't work and some are missing and I personally …

Hi all, I'm new here at the Armbian board. I operate a self made house automation based on a Raspberry using a self written PHP server and Homegear. To have a better wireless connection to a differential temperature sensor, I built a Homegear Gateway based on a Nano Pi Neo with Armbian OS and a 868 MHz CC1101 module. For the network connection I use a Realtek USB WLAN NIC (Realtek RTL8188EUS-Chipset). Most of the time the gateway works. But around 2-3 times per week the gateway hangs and I cannot log on anymore. A hard restart by unplugging power is required. The only indications I find are 2 dumps of the RTL8188EU driver in kern.log…

Hi! I recently upgraded the OS of my OpiZeroLTS, from the Debian Stretch Server 5.3.5 (available distro on Sunxi website) to Debian Buster 5.8.5 (downloaded from armbian webpage). Everything went well, except when I plug my USB webcam several video devices are assigned. I made a script with fswebcam to acquire still pictures from all /dev/video* and these "ghost" cameras are causing errors when the software try to open them as regular webcams. My script: for vid in /dev/video*; do output=$(basename $vid) fswebcam -d $vid -r 1920x1080 -D 10 -S 5 -F 1 --jpeg -1 --no-banner --no-timestamp --no-info /opt/images/$output mv /opt/i…

Hi all! I have Orange Pi One with Armbian Debian 5.8.9-sunxi on board. The problem is that when I catch 2 kHz square wave with OPi gpio, I have very big delta between signals. If I use "interrupt both endges" parameter for gpio, time between signals must be 250 microsecs. But now it floats between 200 - 290 microsecs. And I have achive this result after some suggestions from other forum topics: using isolcpu=3, run c program on this cpu, use max priority, disable powersaving for CPU. I try to read with wiringOP lib, and directly from sysfs, but still have jittering about 90 us. Also I think, that I have not very bad results for cyclict…

Hey guys. I have been trying to utilize H5 vpu decoding for 10+ hours... Still no go. Here is the checklist: kernel Using mainline kernel 5.8.9 from Armbian/build current. `uname -a` output: All kernel configs needed on Sunxi-Cedrus homepage were added, cma set to 256M. libva-v4l2-request Using https://github.com/Sash0k/libva-v4l2-request master. Compiled and make installed. `vainfo` output: `v4l2-ctl --list-formats` output: `./v4l2-request-test -f 25 -l` output: Cpu usage is quite low(4 cores <5%), checked with lsof and…

Hello, I have Orange Pi 3 board. Panfrost drivers works fine bud I accelerated video not working. I have trouble with the drivers... I compile https://gitlab.freedesktop.org/vdpau/libvdpau and https://gitlab.freedesktop.org/vdpau/vdpauinfo When I run vdpauinfo I get: Failed to open VDPAU backend cannot open shared object file libvdpau_sun4i-drv.so No such file or directory Bud i dont know hot to make this .so file... Thank you. ==================================================================================== EDIT (i can post to here only one message per day...). Here is more informatio…

hi guys, i'm using legacy kernel (because im using fbtft). a couple month ago i followed a tutorial on how to install SPI touch and lcd support, now when i try to install it again - im facing issues with downloading the headers - i see the download is not available anymore. so i tried to download the current headers - using: apt install linux-headers-current-sunxi and when i try to run "make" - i face errors regarding SSL certificates and more issues. i followed the exact steps i tired in the past with a clean installation. tried ubuntu and debian (both used to work properly). what am i missing? Maybe i ne…

Hi all. Firstly, sorry I had posted this query in the wrong forum. I´m trying to add support for a raw SPI comunication through SPI0, as it´s a custom comunication with a little auxiliary board, I think best option is to have a spidev device. My scenario is: Banana pi m2 ultra Armbian 5.4.35-sunxi, server (No gui). I have been modifying .dts and .dtsi files, here are parts of the files that I modified: sun8i-r40.dtsi spi0_pins: spi0-pins { pins = "PC0", "PC1", "PC2"; function = "spi0"; }; spi0: spi@1c05000 { compatible = "allwinner,sun8i-spi"; device_type = "spidev"; reg = …

I successfully installed Armbian 20.08.1 to eMMC, and it works fine. Now, I want to try Raspberry OS (I'm told that it works?) but regardless of what I put on my uSD card (I've tried several OS's) - when rebooting the OPi 3+, it always comes up with the eMMC Armbian load. In researching this, I read over and over that the uSD card always has priority over the eMMC. Is this still true with the current version of Armbian? What could explain the behavior I'm seeing? I tried the Install to/update booth loader, both option, with no change in behavior. Any thoughts?

Hello, Earlier on this week I decided to upgrade the kernel and the DTBs on my Armbian cluster (quite a few different boards but all of them based on Allwinner A20) from buster-next-5.92 to buster-current-20.08.2. Having successfully completed the upgrade on several other servers, I moved on to the lime2 one - which promptly failed to come back up after the reboot. Connecting the serial console shows u-boot doing its thing without issues and the kernel beginning to boot, producing normal messages - only to suddenly freeze. When exactly the freeze occurs varies, sometimes it even happens halfway through outputting a message line - but it is definitely before th…

Hi, I installed Armbian image 20.8.1-focal-5.8.5 to Orange Pi PC. I am experiencing issues with playing sounds (tested with playing .wav files). Upon starting playback first 1-2 seconds are omitted and then sound plays as it should. I didn't notice this issue on Xenial (3.4.113). Issue is identical to the ones reported in following threads: https://forum.armbian.com/topic/12059-orange-pi-lite-missing-first-second-of-the-audio-output/ https://forum.armbian.com/topic/12059-orange-pi-lite-missing-first-second-of-the-audio-output/ Has anyone managed to solve it? Thanks

Hello, I have OPI0 with Ubuntu 20.04.1 LTS with Linux 5.8.6-sunxi and I would like to set 240 MHz as minimum frequency. cpufreq-info shows that available steps starts at 480 MHz but on older kernel 240 MHz and 120 MHz were available too. I also tried to "force" 240 and 120 by editing /etc/default/cpufrequtils but no go. Lower reachable frequency is 480 MHz and what I see are a bit CPU higher temperatures. cpufreq-info cpufrequtils 008: cpufreq-info (C) Dominik Brodowski 2004-2009 Report errors and bugs to cpufreq@vger.kernel.org, please. analyzing CPU 0: driver: cpufreq-dt CPUs which run at the same hardware frequency: 0 1 2 3 C…

Hi, I update Armbian (Debian) from Kernel 5.4 to the last version Armbina 20.08.2 with Kernel 5.8.6-sunxi64, but now I don't boot the GUI. I have connected only the power and I can use from other pc from ssh. Thank you for all!

Orange pi pc plus. i have this crazy logs with latest buster regarding the RTL871X wifi chip, it consume up to 5 megs a day on each kern.log, messages and syslog. what can i do to turn this off? my opi's are in the wild and i do have to connect via cellular to check logs at time via vpn and it's not cool to transfer that much data. Thanks.messages

After having my old debian (wheezy? or jessy?) unbootable from systemd update I decided to clean install. Having gotten a good Power supply, an A1 Speed 10 SD card, etcher image, and armbian debian 20.08 (also tried 20.07), The board boots (Welcome to armbian) up to "network interfaces up) - then the screen goes blank/black, and I get the green led heardbeat (slow blinking) for a while. Pushing power again the board shuts down (green LED blinking rapidly for a moment, then red power LED comes off). I have had installed boot to nand / Sata disk before but all that shouldn't matter I think because the boot from SD Card seems successful - why could it be th…

On a fresh install of Armbian 20.08.1/Linux 5.8.5-sunxi on an OPi Zero (256MB version), total memory is 238MB according to "free -m": root@orangepizero:~# free -m total used free shared buff/cache available Mem: 238 74 78 1 85 154 Swap: 119 0 119 238MB is not 256MB. :-) I assume the discrepancy is due to reserved framebuffer memory, but after a bit of testing I've found that the "sunxi_fb_mem_reserve" parameter (set to "16" in /boot/boot.cmd by default) has no apparent effect. Here's a boot with the Armbian default "sunxi_fb_m…

Hi, I just wanted to report this bug. Latest Armbian Buster images for OPi Lite 2 don't work. When they're booted up, it takes 30 seconds for the device to freeze completely. The screen, keyboard, network, everything is frozen after less than a minute. I downgraded to a release from a month ago and it boots up correctly.

Hello, I am using Armbian on a Nanopi Neo Allwinner h3. I build Armbian with the Armbianbuild repository and noticed that the CPU Frequency in all builds (minimal/standard) (buster/focal) are between 480MHz and 1.37GHz, but the H3 Soc only supports up to 1.2GHz. This problem also occurs on the finished builds which are there to download from the Armbian website. (Tried with Armbian Buster kernel 5.8.y and Armbian Bionic 5.8.y) root@nanopineo:~# cpufreq-info cpufrequtils 008: cpufreq-info (C) Dominik Brodowski 2004-2009 Report errors and bugs to cpufreq@vger.kernel.org, please. analyzing CPU 0: driver: cpufreq-dt CPUs which run at the same hardware frequency: …

Looking at the pinout table Pin 7 and PIN26, also the schematic, PWM is PA6 For this board, the overlay, is saying PWM is PA5, is it PA5? (sun50i-h5=pwm.dts) For SPI_1, CS_1 is PA10, but the table does not list a PA10, is that pin 26? (sun50i-h5-spi-add-cs1.dts)

Hello, I am trying to use BPI with legacy Armbian and Stella emulator with 16:10 monitor (using HDMI-DVI cable) I just dont know how to set proper 16:10 resolution. The resolution I set in armbian-config is 1680x1050, but it is different from resolution that Stella uses, when I launch it on the startup. It uses the resolution defined in FEX. So I checked https://linux-sunxi.org/Fex_Guide#disp_init_configuration and tried various resolutions, but dont know which of them is 16:10 and what is the exact resolution. For example 576p can mean anything. How can I find it out? Thank you very much.

I am using a system I built from the trunk of Armbian for the pine64so. After booting up the mouse does not do "smooth mouse tracking". The movement of the mouse lags behind where it should be and has to "catch up" which takes several seconds. I consider it unusable doing this. This is Version "20.04.1 LTS (Focal Fossa)" Armbian 20.08.0-trunk Focal 5.7.17-sunxi64 #trunk Mon Aug 24 03:00:31 PDT 2020 aarch64

Guys please help me. My orange pi one with Armbian installed and running Pi Hole. The HDMI Output is not working, And when I try to enter this command h3disp [-h/-H] -m [video mode] [-d] [-c [0-2] it say access denied. My point is there's no output this play on my device. I hope someone understand me and help me thank you.

Hi guys! I have a problem with Orange Pi 3. After a night leaving the small board turned on I reboot the board and try to use a Bluetooth connector it shutdown. Again and again the same problem. When I touched the board it was so hot. Even when I use outside the case the board can't support a process for at least 30 minutes without turning off. I got the outputs of dmesg. As I don't know, I am a replay newbie, I ask for help here. Best regards. Paulo

So recently i noticed that the os image that i am running on my orange pi 3 is for Z28 pro, that's a tv box, when i firstly booted this board i booted it in an image made for orange pi3 and in the cli when i booted it it said running debian buster based armbian for orange pi 3, i have no idea how it switched to Z28 pro image, i don't even know where to find this image, i didn't modify any of the system files, i just set a nextcloud server, is this normal or not?

Can we switch a 64 bit image from downloads section to 32 bit kernel, repos and apps? I want a 32 bit (armhf) build server, but can see 64 bit OS images only. Do I need to build my custom armbian image? Are there command line examples for build script that produces armhf image instead of aarch64? I prefer H6 SoC instead of H3 because H6 is two times faster than H3, but the price of H6-based boards is very similar to H3-based boards. Thanks in advance

There is a patched version that enables noscan=1 , but the one I'm using seems like it hasn't been patched. When there is no AP's around HT40 kicks in ok without noscan=1. With noscan=1 and AP's are around hostapd won't even start in HT20 mode. Any help? root@orangepilite2:~# modinfo 88x2bu|grep version: version: v5.8.7.1_35809.20191129_COEX20191120-7777 srcversion: 43C721C4A870A632EBDE0B5 parm: rtw_chip_version:int root@orangepilite2:~# uname -a && hostapd -v Linux orangepilite2 5.4.43-sunxi64 #20.05.2 SMP Tue Jun 2 17:20:17 CEST 2020 aarch64 GNU/Linux hostapd v2.9 User space daemon for IEEE 802.11 AP management, IEEE 802.…

Hi, I'm using Armbian Linux on a Cubietruck A20 device configured as a media, file and backup server. Unfortunately while trying to fix a persistent SATA-cable connection problem I accidentally pushed the FEL button on the device. Now the device is always booting in FEL mode searching for USB devices, and I'm unable to reverse this. I have been looking at multiple pages about the FEL mode but I'm unable to find useful information on how to quit or exit this FEL mode and to have the cubietruck booting as it did before. Although I'm not a Linux novice, the information about FEL is quite complex and I have to admit I'm clueless about how to fix this s…

Hello, friends. I am using legacy Armbian 3.x kernel on my development boards where I run Stella emulator with some special USB joystick. The joystick is detected as XBOX controller, hence I guess it uses xpad driver. The problem is that this driver is not present in the latest Armbian so this joystick does not work. I would like to use latest Armbian to have the latest packages, using it as a print/scan/radio server and would like also to play some Atari game from time to time. I tried to build it from the source using this https://github.com/paroj/xpad I can load it with modprobe, the joystick seems to be detected, but it is not working in Stella, I cannot eve…

Hi guys. I've just spent yet another two hours trying to find an answer to my webcam problem and there does not seem to be an answer from what I can discern. Still working to try to get a camera to work with Octopi from what I have around. Strange thing I discovered that the USB OTG port on the Opi One does not seem to work, but when plugged into my single regular USB, I get this for the camera: pi@citrico-opione:~/ffmpeg_cedrus264_H3$ lsusb Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 1908:2310 GEMBIRD Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux …

Hi I want make VPU work on OPI 3 with mainline kernel I apply the LibreELEC Kernel patch and /dev/video0 is registry. I also apply LibreELEC FFMPEG Patch and build with v4l2-request But when I decode videos,VLC did't decode frames and kernel say's : cedrus 1c0e000.video-codec: Missing required codec control Why? What should I do?

I'm trying to get an MCP2515 working with an Orange Pi Zero LTS H2+. Everything seems to go well until I try to bring up the can0 interface using the command ip link set can0 up type can bitrate 500000 Once the command is entered, it never returns. Control+C doesn't do help. New SSH sessions fail to start, but pinging the IP address works fine. Trying ifconfig from the serial terminal will also fail to return. Trying to shutdown after the "ip link set..." command, the shutdown procedure takes a long time, and eventually sends [ 4320.026984] systemd-shutdown[1]: Waiting for process: ifdown, wpa_supplicant, NetworkManager, …

I am trying to connect an SATA -> USB DVD-R drive to OPi3, but it fails, K3b complains about "no drive". Here is syslog: Aug 15 22:12:31 orangepi3 kernel: [34203.588120] usb 3-1.1: new high-speed USB device number 8 using xhci-hcd Aug 15 22:12:31 orangepi3 kernel: [34203.712687] usb 3-1.1: New USB device found, idVendor=13fd, idProduct=084 0, bcdDevice= 1.14 Aug 15 22:12:31 orangepi3 kernel: [34203.712695] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNu mber=3 Aug 15 22:12:31 orangepi3 kernel: [34203.712698] usb 3-1.1: Product: External Aug 15 22:12:31 orangepi3 kernel: [34203.712701] usb 3-1.1: Manufacturer: Generic Aug 15 22:12:31 orange…

Hello. I can't enable HDMI output for A64 on Orangepiwin platform - every time screen is blank (monitor not active). Monitor connected over hdmi to vga adapter. After linux kernel is loaded - monitor is alived. I try some options in boot.scr withnout effect for u-boot: video-mode=sunxi:1024x768-24@60,monitor=dvi,hpd=0,edid=1 video-mode=sunxi:1024x768-24@60,monitor=dvi,hpd=1,edid=1 video-mode=sunxi:1024x768-24@60,monitor=dvi,hpd=0,edid=0 and setenv console=tty0 hdmi.audio=EDID:0 disp.screen0_output_mode=EDID:1024x768p60 Need help.

Hi, I'm facing a problem with my Orange Pi Zero with the latest Armbian version. I noticed that when I provide an internet connection type that is not valid (wrong psk, ethernet but no cable plugged in, etc.) and I reboot the system, it hangs just before asking the username and password. Sometimes it takes up to 10 minutes before keeping going. These are the last boot logs that I see: [ 11.209226] systemd[1]: Starting Create list of static device nodes for the current kernel... [ 11.219428] systemd[1]: Condition check resulted in Load Kernel Module drm being skipped. [ 11.244988] systemd[1]: Started Nameserver information m…

Hello, I am using a orangepi one plus, but that might be no connection with my issue. I am having the following network configuration: # Network is managed by Network manager auto lo iface lo inet loopback allow-hotplug eth0 eth0.1 eth0.10 auto eth0 iface eth0 inet manual pre-up ifconfig $IFACE up post-down ifconfig $IFACE down auto eth0.1 iface eth0.1 inet static address 192.168.1.250 netmask 255.255.255.0 gateway 192.168.1.1 auto eth0.10 iface eth0.10 inet static address 192.168.10.1 netmask 255.255.255.0 if i disconnect the network cable and connect back the interface is not come up automatically from the state it…

I am running Armbian Bionic with Linux Linux 5.4.45-sunxi on an OrangePi PC Plus board. It is running HomeAssistant and a small NodeJS service. Everything is working great, however recently some random shutdowns started. I started investigating and here are my findings: I was unable to SSH or ping the device (it is connected via WIFI) so I connected to the serial pins, but that didn't work either until manual reboot. /var/log/syslog file starts with Aug 12 13:17:04 localhost kernel: [ 0.000000] Booting Linux on physical CPU 0x0 so it looks like the log from before the shutdown disappeared. last -x command only returns: ogrevan…

Hello. I have just acquired an Orange Pi plus 2e. Armbian Xenial is installed on emmc. I wish my SD card to become my /home. Can you help me? Thank you.

Hi everyone, I am trying to setup a new armbian buster system on a lime2 eMMC board. Not currently using the eMMC. Wanted to have a regular armbian install on the sd card, and then an encrypted root partition on an SSD attached with SATA. I've done this before by loosely following this post If I setup a system without using dropbear to unlock the root partition and boot, and use a keyboard to enter the password to unlock it instead, that works fine. However, if I install the `dropbear-initramfs` package, copy my ssh keys to /etc/dropbear-initramfs/authorized_keys and then do `update-initramfs -u` the bootloader doesn't seem to get past the initial stages. Here …

Linux orangepilite2 5.4.43-sunxi64 #20.05.2 SMP Tue Jun 2 17:20:17 CEST 2020 aarch64 GNU/Linux I have managed by accident to get full USB3 speed on orange pi lite 2. I have bought a USB3 hub: "Bus 004 Device 002: ID 05e3:0612 Genesys Logic, Inc. Hub" , I have no idea which chip it has, it is in an aluminum case and looks like the one on the attached picture but black. By attaching atleast two usb devices in the hub USB3 somehow gets into full speed mode, one of them has to be USB2 device. I have managed to get with all devices I have ATM about 2000Gbs including iperf in both directions with rtl8153, hdparm -t on two usb2 memory sticks …

Hi, I have connected Orange Pi Lite over serial UART, but looks like the default settings are to not output the boot log to serial. You can only see U-Boot messages, then "Uncompressing Linux kernel" and after some time the login prompt comes. What exactly do I need to change/configure to get the classic kernel boot log to serial console? Thanks

Good day friends, For some time now I've been trying a DAC (dac-pcm5102mk-i2s) with the Orangepi Pc Plus OS "Debian Stretch with Armbian Linux 4.19.62-sunxi" to put into operation. Unfortunately without success so far. On another Orangepi Pc Plus with Ubuntu Xenial with Armbian Linux 3.4.113-sun8i I activated the DAC after the tutorial I2S on Orange Pi H3 Da Alchemist February 29, 2016. It works fine there. Debin strech does not have a script.bin that I could convert in order to be able to make the settings. I would be happy if someone could help me. Best regards Hans-Jürgen Grigoleit

I am trying to start snap multipass on the device nanopi k1 plus, getting the following error: root@nanopik1plus:~/testSnap# multipass start launch failed: Internal error: qemu-system-x86_64 failed getting vmstate (Process returned exit code: 1) with output: qemu-system-aarch64: -nographic: No machine specified, and there is no default Use -machine help to list supported machines

hello everyone, I managed to make a WaveShare's 3.5" SPI LCD (actually designed for arduino) work on NanoPi Neo Core running on armbian Bionic 4.19.57, but now i"m having some issues with the touchpanel (using the same SPI). i'm trying to figure out how where to connect the touchpanel cs pin, which from what i have read suppose to connect to CE1. could someone help me find out which pin is it? maybe this will help: root@nanopineo:~# dmesg | grep "spi0.1" [ 8.334791] spi spi0.1: spidev spi0.1 1000kHz 8 bits mode=0x00 [ 8.335492] spi spi0.1: spidev spi0.1 1000kHz 8 bits mode=0x00 [ 8.348670] ads7846_device: spidev spi0.1 1000…

Hi - I have been using Armbian buster stable on Orange Pi Zero for the past 12 months, starting with 5.92 last August and going up to 20.05.7 today. In all of these versions, clock speeds above 1.008GHz are unavailable, despite the board supporting 1.104GHz, 1.2GHz, 1.296GHz and 1.368GHz. They are not listed in armbian-config, cpufreq-set is unable to set them, and dmesg includes lines like: [ 10.030991] core: _opp_supported_by_regulators: OPP minuV: 1320000 maxuV: 1320000, not supported by regulator [ 10.031017] cpu cpu0: _opp_add: OPP not supported by regulators (1104000000) [ 10.031305] core: _opp_supported_by_regulators: OPP minuV: 1320000 maxuV:…

The last time I've used this board was around December 2019. Building images or downloaded from Armbian.com and burning them on a SD card worked fine. Now i'm struggling to get it to boot from SD. Tried these images: https://redirect.armbian.com/orangepizeroplus2-h5/Buster_current https://redirect.armbian.com/orangepizeroplus2-h5/Focal_current Also build my own image (to include some extra modules) Armbian_20.08.0-trunk_Orangepizeroplus2-h5_bionic_current_5.7.12 All of them won't get passed "Starting kernel" Serial log: U-Boot SPL 2020.04-armbian (Aug 05 2020 - 07:58:29 +0200) DRAM: 512 MiB Trying …

Hi there, as I've connected my laptop e-mail client (Thunderbird) to my OPi3 I started to receive strange emails "from root ("cron daemon") to root": Subject "Cron <root@orangepi3> /usr/lib/armbian/armbian-truncate-logs" "error: syslog-ng:8 lines must begin with a keyword or a filename (possibly in double quotes) error: unattended-upgrades:10 lines must begin with a keyword or a filename (possibly in double quotes)" What should I do? Line 8 in armbian-truncate-logs is comment, so error is not there.

Hi there, how do I configure / start an WiFi AP on OPi3? In armbian-config (found using google, and found on OPiPC+) from my current Buster (OOB + update / upgrade) there is NO option to set up an AP. I may configure it "manually" (edit config files) but I need some tutorial if there is no "menu style" config.

Today I updated my BananaPI M1 board, replaced the Bananian OS with Armbian Armbian_20.05.4_Bananapi_focal_current_5.4.45.img. I'm not getting the SATA with connected 1TB WD10JFCX working. The HD worked before with the Bananien kernel 3.4.x What can I do, how can I test, how can i get more information about the reason? The board is powered via the Micro USB and armbianmonitor reports DC-IN voltage > 5V

When I try to read the input on PA19 immediately goes to "1" even though there is no voltage being sent to the pin. Example: #!/usr/local/bin/python from pyA20.gpio import gpio from pyA20.gpio import port pin_to_circuit = port.PA19 gpio.init() gpio.setcfg(pin_to_circuit, gpio.OUTPUT) gpio.output(pin_to_circuit, 0) gpio.setcfg(pin_to_circuit, gpio.INPUT) print(gpio.input(pin_to_circuit)) I don't understand why this would put "1" with nothing even connected to the PA19 pin? Are there some settings I need to change to get PA19 working as a normal GPIO pin?

1.Only OpenGL ES2.1 and 1.x work: chenyifei@orangepi3:~$ glxinfo|grep OpenGL OpenGL vendor string: Panfrost OpenGL renderer string: Mali T720 (Panfrost) OpenGL version string: 2.1 Mesa 20.2.0-devel OpenGL shading language version string: 1.20 OpenGL extensions: OpenGL ES profile version string: OpenGL ES 2.0 Mesa 20.2.0-devel OpenGL ES profile shading language version string: OpenGL ES GLSL ES 1.0.16 2.glx did't work with panfrost dri: chenyifei@orangepi3:~$ cat /var/log/Xorg.0.log|grep GL [ 10447.384] (II) Initializing extension GLX [ 10447.384] (EE) AIGLX error: sun4i-drm does not export required DRI extension [ 10447.395] (II) IGLX: Load…

Hi, I'm having some instability issues with WiFi driver on Orange Pi Zero Plus, it uses RTL8189FTV instead of buggy XR819 chip. Some times it just works fine, but that's not always the case, some times when I turn on the board the driver is not able to turn on the WiFi chip, and it keeps stuck in a limbo state... The kernel identify the network device as (wlan0), but it's impossible to turn on or connect to any network. sudo dmesg | grep -Ei '(8192eu|rtl|wl|realtek)' [ 236.057560] RTL871X: Failed to init Power On! [ 236.057567] RTL871X: rtw_hal_init: hal__init fail [ 236.057573] RTL871X: -ips_netdrv_open - drv_open failure, bup=1 [ 236.057579] RTL8…

Hi there, I need help in finding the lates Debian Buster image for my R1. Please can you point me to the latest version ? Many Thanks Wollik

Hello, Im trying to get 2 Uarts working on an Orange Pi Zero+2. Im using armbian Buster image for OPiZ+2 Linux orangepizeroplus2-h3 5.4.43-sunxi #20.05.2 SMP Mon Jun 1 18:26:22 CEST 2020 armv7l GNU/Linux I added UART1, UART2 and UART3 to armbianEnv.txt and was able to read / write on ttyS2 on pins 8 (PA00) and 10 (PA01). But couldnt find which pins ttyS1 or ttyS3 are on. I read at that UART 3 should be Tx PA13 Pin 24 Rx PA14 Pin 23 Is anyone able to suggest which pins I can use for a 2nd UART and is there a file I can look in to find the configuration for the UART Overlays ? Thanks Chris …

DTS overlay to activate I2S DAC 5102a on Armbian Buster 5.4.43 armbian-add-overlay sun50i-h5-i2s0-out.dts If you don't have headers armbian-config (software->headers) Manual install whithout headers mkdir /boot/overlay-user/ dtc -I dts -O dtb sun50i-h5-i2s0-out-no-header.dts -o /boot/overlay-user/sun50i-h5-i2s0-out.dtbo add user_overlays=sun50i-h5-i2s0-out to /boot/armbianEnv.txt sun50i-h5-i2s0-out.dts /dts-v1/; /plugin/; / { compatible = "allwinner,sun50i-h5"; fragment@0 { target-path = "/"; __overlay__ { pcm5102a: pcm5102a { #sound-dai-cells = < 0x00 >; compatible = "ti,pcm5102a"; status = "okay"…

I am not sure if this is intended or bug, When building the image for Nanopi duo2 I cannot add kvm. This worked before so I guess that this is regression. I get this search result for kvm in the build process: ┌──────────────────────────────────────────────────────────────────────────────────────────────────────────────────────── Search Results ────────────────────────────────────────────────────────────────────────────────────────────────────────────────────────┐ │ Symbol: KVM [=KVM] …

I want to make panfrost work on H6 platform, I use linux 5.6.16 latest mesa Xorg 1.20 I install and run them. But they dispaly : DRM_IOCTL_PANFROST_MMAP_BO failed: No such file or directory What should I do?

Hi all, i am trying to enable UART4 on my Cubieboard2 via /boot/armbianEnv.txt: overlay_prefix=sun7i-a20 overlays=i2c1 uart4 param_uart4_pins=a but if it seems that my uart4 is not working. If i look at dmesg | grep tty there is no ttyS4-device - only ttyS0: [ 0.000000] Kernel command line: console=tty1 root=/dev/mmcblk0p1 rootwait rootfstype=ext4 sunxi_ve_mem_reserve=0 sunxi_g2d_mem_reserve=0 sunxi_no_mali_mem_reserve sunxi_fb_mem_reserve=16 hdmi.audio=EDID:0 disp.screen0_output_mode=1920x1080p60 panic=10 consoleblank=0 enforcing=0 loglevel=1 [ 0.000860] console [tty1] enabled [ 1.542600] 1c28000.ser…

I am using Armbian_20.05.4_Lime-a64_focal_current_5.4.45_desktop.img.xz and I try run glxgears on Olinuxino-A64 with Lima. When I running glxgears I see 117 frames in 5.0 second = 23.313FPS. Also mouse response so slow on desktop. It is understood from here Olinuxino-A64 doing software render. Please correct me if I am wrong. I am new at this job and I have difficulty in fully understanding the problem. Is there a way I can get high FPS in glxgears using Lima? What exactly is problem here? Sorry if I ask silly question. Thanks. Below are some outputs for the board I use. dmesg | grep "lima" output: [ 8.579828] lima 1c40000.gpu: IRQ ppmmu2 not found [ …

Hello, i am new here and need the line in from MCU audio codec(U1-3 Pin AB20 & AB21), located wired on CSI connector(CON1 Pin 1 & 2), active. Is it possible? Regards Mario

Hello, on a Banana Pro, is there a way to disable on board wifi? I am using Armbian Buster. Thank you, Alex.

... [ OK ] Finished Set console font and keymap. [ OK ] Finished Helper to synchronize boot up for ifupdown. Starting Raise network interfaces... [ OK ] Started udev Kernel Device Manager. [ OK ] Found device /dev/ttyGS0. [ 14.547006] thermal thermal_zone0: binding zone cpu_thermal with cdev thermal-cpufreq-0 failed:-22 I just installed Armbian Focal on my Orange Pi Zero and i receive this error on startup, then the boot stops here. It did pass this step a couple times but 90% of the time it will not boot. Thanks in advance, //Hasan

I am running Armbian Focal with Linux 5.4.43-sunxi64 (and now downgraded to 4.19.125-sunxi64) on my Orange Pi PC 2. I use motion software to provide a "18ec:5555 Arkmicro Technologies Inc. USB2.0 PC CAMERA" to the network. I also use pjsip to provide SIP functionality for the same device as audio input. As soon as I start pjsip for some reason I get a very high load average until the kernel detectets stalled CPUs and finally the entire device crashes. This worked fine in a previous version and started after I upgraded to focal. I did a kernel backtrace and this is what I got: [ 401.002517] sysrq: Show backtrace of all active CPUs [ 401.009965] sysrq: CPU1: [ 401.01…

Spoiler [55881.786168] 8<--- cut here --- [55881.789254] Unable to handle kernel paging request at virtual address bfd60e58 [55881.796482] pgd = 7d7d1ef9 [55881.799191] [bfd60e58] *pgd=00000000 [55881.802777] Internal error: Oops: 80000005 [#1] SMP THUMB2 [55881.808261] Modules linked in: rfkill zstd snd_soc_hdmi_codec dw_hdmi_cec dw_hdmi_i2s_audio sun8i_codec_analog snd_soc_simple_card sun8i_adda_pr_regmap sun4i_i2s snd_soc_simple_card_utils snd_soc_core ac97_bus sun8i_drm_hdmi snd_pcm_dmaengine snd_pcm dw_hdmi sun4i_gpadc_iio lima snd_timer industrialio cec sunxi_cedrus(C) snd gpu_sched v4l2_mem2mem sun8i_thermal soundcore videobuf2_dma_contig videobuf2_memo…

Hi all. I have a board nanopi neo air with armbian linux on it. We with my colleague try to setting up ffmpeg with cedrus264 for hardware accelerated capturing video from ov5640-like camera device. There is my armbianmonitor. There are my v4l2-ctl -d /dev/videox -D out: Spoiler Driver Info: Driver name : cedrus Card type : cedrus Bus info : platform:cedrus Driver version : 5.4.51 Capabilities : 0x84208000 Video Memory-to-Memory Streaming Extended Pix Format Device Capabilities Device Caps : 0x042080…