Allwinner sunxi

All, Does anyone know how I can enable the OnBoard Wifi using Armbian? Is there a driver included for for the XR819 on-board WiFi module? any pointers would be much appreciated.... Thanks Gerry

Has anyone managed to get video encoder working with the latest mainline kernel? I'm getting stuck trying to compile the cedar_ve kernel driver from https://github.com/uboborov/sunxi-cedar-mainline I have downloaded the kernel source using armbian-config and then built the sunxi-cedar-mainline kernel driver. However, I fail to load the driver due to version magic: When trying to force the load: But no dmesg message about magic check failure.

Hello... I've got an Orange Pi Zero Plus 2 H3 with Armbian Stretch. Kernel: 4.14.70-sunxi armbianEnv.txt: I did: cp -a /lib/firmware/ap6212/fw_bcm43438a1.bin /lib/firmware/brcm/brcmfmac43430-sdio.bin dmesg when searching for "brcm" gives me: [ 8.123186] brcmfmac: brcmf_fw_map_chip_to_name: using brcm/brcmfmac43430-sdio.bin for chip 0x00a9a6(43430) rev 0x000001 [ 8.256708] brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0: Oct 8 2016 15:31:47 version 7.46.57.4.ap.r4 (A1 Station/P2P) FWID 01-3621395e es6.c5.n4.a3 In /etc/default/ap6212 I have: PORT=ttyS1 But the scr…

Orange Pi Prime (H5) Armbian_5.59_Orangepiprime_Debian_stretch_next_4.14.65.img 1. Installed OK, installed LXDE-desktop OK, removed XFCE4 OK. 2. Normal temperature 42, ocassionally up to 73, occasional reset. Ordered some heatsinks. 3. Keepass2 fails to load (runs under mono): dk@orangepiprime:~$ keepass2 Gtk-Message: Failed to load module "atk-bridge" System.ArgumentException: A null reference or invalid value was found [GDI+ status: InvalidParameter] at System.Drawing.GDIPlus.CheckStatus (System.Drawing.Status status) [0x0009b] in <1917aa1c39d94b1a91807b8cd9f03350>:0 at System.Drawing.Bitmap..ctor (System.Int32 width, System.I…

My orange Pi Zero 2W does not boot with all accessible images. Following error is displayed - [/ init]: getty is ttyl [/init]: RootDevice is "/dev/mtdblock4" , GPT_SUPPORT=1 [/ init]: Try to load Nor mount: mounting /dev/mtdbIock4 on /mnt failed: No such file or directory [/init]: Failed to mount /dev/mtdbIock4! / #_ Can any member provide me a path to fix this error and boot my Orange Pi Zero 2W?

I am trying to set up Wifi AP on OrangePi Zero board. Basically, I install and configure hostapd and dnsmasq and create a script, which does the following (it is run as sudo): nmcli radio wifi off rfkill unblock wlan ifconfig wlan0 172.16.0.1 netmask 255.255.255.0 broadcast 172.16.1.255 service dnsmasq restart /usr/sbin/hostapd /etc/hostapd/hostapd.conf This is the /etc/dnsmasq.conf: port=53 domain-needed bogus-priv resolv-file=/etc/dnsmasq/resolv.conf interface=wlan0 listen-address=172.16.0.1 bind-interfaces addn-hosts=/etc/dnsmasq/hosts.conf dhcp-range=172.16.0.50,172.16.0.150,12h dhcp-leasefile=/var/lib/misc/dnsmasq.…

Hello guys! I'm beginner of Armbian. The problem is: Install Armbian Stretch mainline kernel 4.14.y on my device(Orange_Pi_PC),But I don't know how to enable UART1 . I tried to select UART1 & UART2 & UART3 on armbian-config,now i can see 'overlays=uart1 uart2 uart3' in /boot/armbianEnv.txt Connect serial device with P40(RX) P39(GND) P38(TX) . when i check serial device on ssh, i can see this info: uname -a Linux orangepipc 4.14.84-sunxi #3 SMP Sat Dec 1 07:18:41 CET 2018 armv7l GNU/Linux ls -l /dev/ttyS* crw--w---- 1 root tty 4, 64 Dec 4 20:24 /dev/ttyS0 crw-rw---- 1 root dialout 4, 65 Dec …

First i have to say - if i knew what i am gonna go through, i would never buy this troubled hardware. So don't buy it too. But if you are already strayed like me, i decided to share my modifications, to make this inconsiderate piece of hardware useful. With this mods the device finally work as i need it to and i am fully happy with hardware part. Not so happy with software though, but that's another story. The main reason for me, to buy this router, except pc like capabilities, was SATA+SATA power connector. I used my old router with usb HDD, so it sounded good to have it in box and on native sata interface. Silly me, who would thought this will be the most troubled …

Hi guys. I've just spent yet another two hours trying to find an answer to my webcam problem and there does not seem to be an answer from what I can discern. Still working to try to get a camera to work with Octopi from what I have around. Strange thing I discovered that the USB OTG port on the Opi One does not seem to work, but when plugged into my single regular USB, I get this for the camera: pi@citrico-opione:~/ffmpeg_cedrus264_H3$ lsusb Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 1908:2310 GEMBIRD Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux …

Board OrangePi+2E, Debian on SD was configured/tested, then nand-instaled to eMMC. Worked as Nextcloud headless server like a charm for more than year (thanks Armbian once again), but suddenly got stuck in boot with quite strange simptoms (read on attacched for exploration HDMI): couple of "sunxi_i2c_do_xfer incomplete xfer" errors /swap creation takes ~100 seconds then complete hang on Ethernet init The only thing I can suspect is some corruption in filesystem(s) on eMMC, but I see no chance to investigate this further as boot from it hangs completely. Fresh SD with mainline Debian boots and works with no issues, so the rest of the …

HI to all, excuse me but this is my first msg. I have a OPI3 board and I try different OS (Arabian, Ubuntu, Debian) all in different release but I do not have wifi and lan. for wifi I have already try with copy firmware file but is is the same for lan I have in dmesg eth0. UP and DOWN. In my experience I have found only Ubuntu Xenial 4.9.118 on the Orange.org web site with wifi OK. can you help me? Thanks

A few months ago I dried one of my OPiPC with a 12V power supply and I have not had a chance to try and revive it. So I am looking to migrate the existing 128GB sd card to a OPi Zero. From what I understand, the following would need to be done Mount the SD card (ideally on a linux BOX or VM) Replace script.bin with a suitable file Sync Eject Enjoy Can anyone confirm? Do I need to swap the kernel as well, or is it ok to keep the existing one? As for the script.bin, what's the best way to get one? Download an image and mount it, use fex2bin to generate one? Any help is appreciated. Than…

Hi all. I have problem with SPI on my board . I find solution but I want to know why .. On first : Linux orangepizero 5.4.20-sunxi #20.02.1 SMP Mon Feb 17 02:09:41 CET 2020 armv7l armv7l armv7l GNU/Linux If go to armbian-config and enable SpiDev .. then reboot not find SPI device on my dev tree .. if look to armbianEnv.txt there is spi-spidev but on dev tree no SPI device .. My solution is this : on /boot/dtb/overlay is file sun8i-h3-spi-spidev.dtbo , decompile it and there is this text : /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { target-path = "/aliases"; __overlay__ { spi0 = "/soc/spi@01c6…

Hi , I want to try out a project for a friend of mine and use an orange pi zero (for now , stronger model might replace it later) to do the following : have an outdoor ip cam connect with wifi on the orange pi zero Save videos on motion detect on pi`s memory Upload saved videos to a remote server (could be ftp) eg. every midnight with internet access via ethernet Keypoints : ipcamera must connect with pi`s wifi pi will connect to a router (via ethernet) a couple hours per day so the setup must not be internet based or with any extra equipment except the pi and the ipcam My thought of doing it : …

Hi I would like to ask you how to use MAX485 module to communicate 2 NanoPi Neo Core 2. I would like to use UART0 (it is GPIO4 and 5). I connection my module similar to this picture: https://www.google.com/search?q=max+485&client=ubuntu&hs=ern&channel=fs&tbm=isch&source=iu&ictx=1&fir=FN56jmGIPP4yJM%3A%2CBP52RgiAvdjG4M%2C_&vet=1&usg=AI4_-kQK1TQEVXzv7J4_kJ8nEnLbgH0X5w&sa=X&ved=2ahUKEwjxy57J2oHhAhVpsosKHZTnCnAQ9QEwBHoECAUQDA#imgrc=Jkfuqm9JL_mJXM:&vet=1 I wrote python3 code send.py : import RPi.GPIO as GPIO import time import serial import os EN_485 = 24 GPIO.setmode(GPIO.BOARD) GPIO.setup(EN_485,GPIO.OU…

I think 16 seconds is the max. value of the watchdog timeout of H2/H3, However, I cannot set it to 16 seconds. When watchdog-timeout = 16 in /etc/watchdog.conf, the timeout is 11 seconds : /etc/watchdog.conf max-load-1 = 24 watchdog-device = /dev/watchdog realtime = yes priority = 1 watchdog-timeout = 16 interval = 3 root@orangepizero:~# systemctl status watchdog.service ● watchdog.service - watchdog daemon Loaded: loaded (/lib/systemd/system/watchdog.service; enabled; vendor preset: enabled) Active: active (running) since Mon 2018-01-29 11:10:27 HKT; 3min 31s ago Process: 851 ExecStart=/bin/sh -c [ $run_watchdog != 1 ] || exec /usr/sbin/wa…

Hi, Just signed on - I've got Armbian running on my BananaPI (i.e. the original plain Jane BPi) - and liking it on there so far. So - I was impressed with Armbian on there - and shelled out and got the OPi+ 2E - flashed an SDCard with Armbian - booted up - and really liking it. Only got it yesterday (took like a month after arriving in the country [AU]). Did nand-sata-install, successful and rebooted - and now running Armbian off eMMC - runs sweet. Really impressed so far - VASTLY better experience than Pine64 (I'm looking for a desktop experience on Arm - for no other reason than "because it's there"). Got Chromium browser working - synergy KVM and Plan…

Hi all. I recently bought an Orange Pi Lite. After trying to get the power switch to work as a power switch (by this I mean booting the board when it was previously shutdown), and after searching for a while, it seems that the power switch in the Orange Pi Lite is not a real one, but it's instead connected to a GPIO. Do you guys know of any Orange Pi board that implements a proper power switch? Thanks.

Hello everyone! it is possible to make dual-boot between Armbian and a Android custom rom on Orange pi pc (h3)? I have only a sandisk extreme 64gb U3. I haven't other cards where to put Armbian and Android separated. Thanks in advance!

hello, i have installed WiringOP it works good for switching relay module but I cannot make DHT 22 to work. Output looks like this Humidity = 0.0 % Temperature = 0.0 *C (32.0 *F) Humidity = 0.0 % Temperature = 0.0 *C (32.0 *F) Humidity = 0.0 % Temperature = 0.0 *C (32.0 *F) Humidity = 0.0 % Temperature = 0.0 *C (32.0 *F) Humidity = 0.0 % Temperature = 0.0 *C (32.0 *F) Humidity = 0.0 % Temperature = 0.0 *C (32.0 *F) Humidity = 0.0 % Temperature = 0.0 *C (32.0 *F) Humidity = 0.0 % Temperature = 0.0 *C (32.0 *F) Data not good, skip Humidity = 0.0 % Temperature = 0.0 *C (32.0 *F) Data not good, skip On one line there were possible good values bud it was one line of 1000.…

Hi all. I build Armbian for "orangepipcplus" as described here: https://docs.armbian.com/Developer-Guide_Build-Preparation/ After build finished, I've got Armbian_5.24_Orangepipcplus_Ubuntu_xenial_3.4.113.img image, flash it to SD card, and my OPi starts well, thanks! All things that necessary for my work tasks - works fine: USB, USB OTG, WiFi, but... no Ethernet :-( When I plug Ethernet cable into my PC and OPi - no LED blinks at both sides (but Ethernet on PC 100% works, tested with Raspberry Pi, for example). In console kernel logs I see the following: [ **] A start job is running for Raise network interfaces (26s / 5min 6s) And OPi actually wa…

So I have an OPI0 perfectly running then suddenly it freezes. All I can find on /var/log/syslog Jul 1 10:35:10 localhost CRON[1553]: (root) CMD (command -v debian-sa1 > /dev/null && debian-sa1 1 1) Jul 1 10:36:08 localhost rsyslogd-2007: action 'action 10' suspended, next retry is Sun Jul 1 10:36:38 2018 [v8.16.0 try http://www.rsyslog.com/e/2007 ] Jul 1 10:37:07 localhost rsyslogd-2007: action 'action 10' suspended, next retry is Sun Jul 1 10:37:37 2018 [v8.16.0 try http://www.rsyslog.com/e/2007 ] Jul 1 10:38:07 localhost rsyslogd-2007: action 'action 10' suspended, next retry is Sun Jul 1 10:38:37 2018 [v8.16.0 try http://www.rsyslog.com/e/200…

The topic is no longer new, but I have not found the reason and its solution! If you turn off the power (just pull out the wire) then you can get a non-working system. As I noticed, the files opened at the time of launch are broken. And some files such as /etc/boot/armbianEnv.txt in general, they are recorded with some kind of garbage!!! Because of this, your settings fly off! For example, I use ttys1 and this option is registered armbianEnv.txt , but after the power loss, there is just terrible garbage in this file, as if the memory dump fell there!!! For example, I still use dotnet, so it also breaks down and does not start anymore!! When y…

Hi, i recently installed jessie (vanilla) on a cubietruck. I have problems with a usb stick to be correctly detected. It is a rf stick to communicate with Homematic devices (HM-CFG-USB). When I plug it in, I get following messages in syslog: Feb 8 21:34:38 localhost kernel: [ 5043.855985] usb 3-1: new full-speed USB device number 8 using ohci-platform Feb 8 21:34:38 localhost kernel: [ 5044.079007] usb 3-1: New USB device found, idVendor=1b1f, idProduct=c00f Feb 8 21:34:38 localhost kernel: [ 5044.079041] usb 3-1: New USB device strings: Mfr=4, Product=14, SerialNumber=36 Feb 8 21:34:38 localhost kernel: [ 5044.079060] usb 3-1: Product: HM-CFG-USB Feb 8…

Orange Pi Win Plus - no screen image after uboot, during uboot operation, the image on the screen is present. Are there any assumptions how to fix this? i tried use image from orange pi win, looks like boars a similar, difference only in wifi and 2gb memory instead 1gb;

Hello all. Okay: I am a total newbie to Orange Pi. I apologize upfront for any and all obvious self inflicted mistakes that you all spot. AGAIN: total newbie to the Orange Pi world. Please go easy in me! I have an Orange Pi Win Plus A64 board and frankly --- I love the darn thing! Powerful for my needs and I have a niche application that I am working on and this board is really the only one that fits my needs. The 2GB RAM is a must. The issue I am having is this: I am usinga waveshare 10.1 inch TFT HDMI display that has the SPI connector (lcd: https://www.waveshare.com/wiki/10.1inch_HDMI_LCD). I have att…

hi all i'm trying to boot my orange pi over the network. i have written u-boot into SPI-Flash memory. i modified boot.cmd script to download the kernel, init ram and script.bin from TFTP server. after downloading them all the kernel tries to start but it dose not proceed. I've attached the screenshot of the console. My boot.cmd Spoiler # DO NOT EDIT THIS FILE # # Please edit /boot/armbianEnv.txt to set supported parameters # setenv serverip 172.20.20.200 setenv load_addr "0x44000000" setenv overlay_error "false" # default values setenv rootdev "/dev/nfs" setenv verbosity "1" setenv console "both" setenv disp_mem_reser…

I tried to install Wireguard on my Orange Pi Zero Plus but without luck. I've followed the install instructions for Debian on Wireguard website, installed the correct linux-headers for my board, updated the packages, but i get this error: apt install wireguard Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have …

Hello, on older Orange Pi zero I used nmcli for creating access point or connecting as a client to wifi. Now I am running Linux orangepizeroplus2 3.4.113-sun8i #4 SMP PREEMPT Wed Nov 22 13:45:28 CET 2017 armv7l on Orange Pi Zero plus2 h3 but I am not able to create access point with this (it does not work as on older OpiZero, I am using the same commands): nmcli c add type wifi ifname wlan0 con-name connection-name autoconnect no ssid hotspotssid nmcli connection modify connection-name 802-11-wireless.mode ap 802-11-wireless.band bg ipv4.method shared nmcli connection modify connection-name wifi-sec.key-mgmt wpa-psk nmcli connection modify connection-name …

Hello, i try to move it from SD to eMMC on a Orange Pi Zero +2 H5, but without success. Shouldn't be two partion created on eMMC by the nand-sata-install script ? root@orangepizeroplus2:~# fdisk -l /dev/mmcblk2 Disk /dev/mmcblk2: 7.3 GiB, 7818182656 bytes, 15269888 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0xe8c6ce8d Device Boot Start End Sectors Size Id Type /dev/mmcblk2p1 8192 15117183 15108992 7.2G 83 Linux Old UUID: /dev/mmcblk0p1 SD UUID: UUID=85ffa85e-4784-4cfd-93bb-db6f93f8e…

Hello, I tried several times to install debian in eMMC on Lime2, using nand-sata-install, without success, getting with the message : "There are no targets. Please check your drives." Note that on the same board, the official debian image provided by Olimex is working and can be installed in eMMC Checking with "dmesg | grep mmc", I don't find mmcblk1 (only mmcblk0). I tried with 3.4.112 image from armbian (also with 4.5.2). I installed a lot of images on Lime2 in NAND, so I'm not so unexperienced, but I don't understand where I'm wrong (or what I don't know) Thanks for any help ! Regards,

Hey there, I have two questions and one of those may be pretty dumb, but anyway. What is the issue that the onboard network is disabled at the moment? The other question is about the tested 3rd party hardware which include various LAN and WLAN adapters. Have those indeed tested with the current experimental images and working? Or is the network support disabled in the current builds at all? Best regards Werner

Is it possible to upgrade my running armbian server version to the desktop one? Thanks...

I just ordered a couple of Orange Pi Zero systems to use in small IoT projects. Reading the forum I see the wireless for Orange Pi Zero might have issues. But some of the posts wanted to use it as an AP. That's not my case, I'll test them when they get here, but just how bad is it? I will not have a heavy load, but I would like something stable. When push comes to shove should I plan on using an Ethernet cable rather than the wifi?

I've upgrade armbian to 5.31, now I have 2 freeze in 2 days Here my log http://sprunge.us/gUeO

Hello, my BananaPi M1 sometimes just stops working. The maximum uptime is 5 days. Usually the time is shorter. The system simply hangs. I can no longer access the system via SSH. When I connect a monitor to HDMI, nothing is displayed, so I can log in. I have connected an external hard drive that is self-powered. I know the stories with the power supply. I have run ' stress -c 2 -m 1 '. The system remains stable. Time CPU load %cpu %sys %usr %nice %io %irq CPU PMIC DC-IN C.St 19:09:19: --- 0.69 10% 5% 5% 4% 0% 0% 49.3°C 42.4°C 5.10V 0/6 19:09:49: --- 2.16 100% 33% 66% 0% 0% 0% 50.2°C 43.6°C 5.10V 0/6 19:10:16: --- 3.18 100% 33% 65% 0% 0% 1% 50.2°C 44.…

I have Orange PI Zero running the stable Ubuntu image. Kernel: Linux orangepizero 3.4.113-sun8i. I'm writing a python3 app to communicate with an Arduino using UART. The app works fine for a few hours and then it stops being able to send or receive commands to/from the Arduino. Is there some known issue with the UART on OPI Zero? It looks like the file descriptor for the serial port becomes unavailable somehow.

From the CLI that is. I plan on using the OPi as a headless MIDI processor, and I'd like to be able to switch remotely the audio output of ALSA between the default audio-out, the HDMI out and a USB sound card (CM108-based, tested working with the current kernel). ALSA documentation isn't well maintained, most of it is old and doesn't correspond with the current state of the software (config files locations and names, contents etc). I tried various examples I found on several bulletin boards, but none really worked since Armbian seems to do things a bit differently. So I'm asking here: on Armbian, how do I switch remotely the output audio device in ALSA? No remote …

I know Lamobo-r1 has many problems and that the support ended, but it works fine for me. Everything works fine with kernel 4.14.84-sunxi, however, when I update the kernel, the b53 switch does not work anymore. I need to update the kernel to add another wifi usb dongle that seems to work only with newer kernels (https://github.com/aircrack-ng/rtl8812au/issues/272#issuecomment-467983704). Anybody experiencing the same problem? Any ideas for a workaround?

Hello Igor, Hello community, What I have: 1 Raspberry PI B (its just a toy) 1 Radxa Rock (bad SW support, will replace Odroid C1 in case AP is running stable, maybe never) 2 Banana PIs (file server) 1 Odroid C1 (AD DC and AP, but actually I have no trust in the hardware) since one of my Banana PI has trouble with SATA (will not initialize, but seems to be NO power problem) I will buy a new A20 board... - Cubieboard 2: too old, no Gigabit LAN, too expensive from my point of view - Cubietruck: too expensive from my point of view - Orange PI: reading forums... seems to have some HW problems, USB Host and/or SATA not functional, etc.) - Banana PI: I like…

Hi all, any advice to enable i2s audio in mainline kernel? I'm on 5.23 cubietruck mainline v4.8.6. Cant find any reference to write DTS...any help would be appreciated. Thank you

Hi guys, I'm getting this error while trying to boot my Banana Pi with an SD card. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... Found U-Boot script /boot/boot.scr 2447 bytes read in 211 ms (10.7KiB/s) ##Executing script at 43100000 Wrong image format for "source" command SCRIPT FAILED: Continuing... scanning bus for devices... Found 0 device(s). SCSI device 0: Device 0: not available [...] I'm coming from using Lubuntu with no problems for nearly a year. The SD card works no problem (or at least it worked perfectly fine with Lubuntu). I also tested with a way faster microSD 64GB I usually hav…

Hello. I have an Orange Pi Zero board with Armbian on it. I want to use its serial pins for flashing arduinos. Right now I only have 1x3 serial pins and 1x13 media (?) pins soldered, the 2x13 GPIO doesn't have any pins and I don't have any spare ones to solder (alright, I might have some, but I'm too lazy for that). That means I only have access to UART0 pins which are currently reserved for Linux console. With RPi Zero and Raspbian the same problem was solved by simply removing "console=ttyAMA0,115200" from kernel options. However, Armbian seems to generate kernel options entirely from armbianEnv.txt, making it impossible to manually remove ser…

Hello there! Its nice to meet everyone and thank you so much for having me! I have this great project i'm working on involving 30 orange pi zeros. You see SD cards are expensive when you need to buy 30 of them so I have been trying for about a month now to make armbian work without the SD card. The idea is to boot into the os get a few things running and then remove the card and boot another pi. I have tried creating a ramfs mount and copying/mounting (what I believe are) all the requirements and then using chroot. But that doesnt work at all. I'm imagining that outside of chroot services are still running and once they cant write to some file…

Hi Martin and others I started a new Thread because have problems using some third party interfaces with OrangePI running Armbian. Well.. In my project I need to communicate with 5 sensors which have UART output so I decided to buy a circuit (uart2spi) which work well if connected to Arduino. The Circuit description is available here: http://www.rowlandtechnology.com/projects/2015/09/25/spi-to-4-x-uart-bridge-multiuart-project/ First step: This is how I have connected the circuit to GPIO bus on my OrangePi pc.. The circuit has (from left to right) +3.3V pin, MISO, MOSI, SCK (clock), CS and GND.. I have connected…

My build process stoped with [ o.k. ] Install locales [ en_US.UTF-8 ] chroot: failed to run command `/bin/bash': No such file or directory chroot: failed to run command `/bin/bash': No such file or directory chroot: failed to run command `/bin/bash': No such file or directory chroot: failed to run command `/bin/bash': No such file or directory [ error ] Installation of package failed I take a look at 'debootstrap.sh' Aller 'Install locales' come at line 146, The command is at line 147 is : LC_ALL=C LANGUAGE=C LANG=C chroot $DEST/cache/sdcard /bin/bash -c "apt-get -y -qq install locales" while .... there is another similar 'chroot $DEST/cache/sdcard /bin/bash' command…

Just got mine Prime and installed on microsd Armbian-server for that. After setting up root password and new user, have edited /etc/network/interfaces to have uncommented these lines source /etc/network/interfaces.d/* auto eth0 iface eth0 inet static address 192.168.0.106 netmask 255.255.255.0 gateway 192.168.0.1 dns-nameservers 8.8.8.8 8.8.4.4 auto lo iface lo inet loopback every manual says it should be easy like that... but it doesn't work where to dig next?

Hello Ones again I need Your advice for steering RGB LED APA106. I try to search for any program to control this Led but most of them is for RPI and it`s not work for My OPI. Is this connection for DIN should by for any SPI1?: Do You have idea how to for example set change color of led ? Regards

Hi, How can I enable both the CS0 and CS1 on the SPI on OPiPC mainline? Need to have both spidev0.0 and spidev0.1 drivers concurently available, yet only one of them is enabled and visible. My armbianEnv.txt verbosity=1 logo=disabled console=both disp_mode=1920x1080p60 overlay_prefix=sun8i-h3 rootdev=UUID=72c69678-cb49-4c08-b5d3-396060e8ff18 rootfstype=ext4 overlays=spi-add-cs1 spi-spidev param_spidev_spi_bus=0 param_spidev_spi_cs=1 param_spidev_spi_cs=0 param_spidev_max_freq=10000000 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u If the latest param is param_spidev_spi_cs=1 then I get only spidev0.1, if the latest param is param_spi…

Good morning, first of all sorry for my English, I'm not native and I use a translator. I'm working on a project with the orange pi plus 2e and I need to protect the internal memory emmc, I installed in emmc "ARMBIAN 5.25 stable Debian GNU / Linux 8 (jessie) 3.4.113-sun8i" and I ask myself the following: How can I protect the internal memory so that it is not accessible by inserting an SD card and mounting the emmc partition? That is, I give my client the orange pi configured and no sd card inserted, starts with emmc, but if someone inserts an sd card with any image for this card can mount the internal partition and access the contents. I've looked at encryp…

Apologies if this is documented/reported somewhere else, but I can't see anything on a quick forum search. I received two Orange Pi Zeros this morning, and eagerly downloaded the Orange Pi Zero flavour of Armbian (Xenial Legacy) and loaded it up on a good 8GB microSD. I then started using it, updating it, and suddenly realised that it only had a 1.4GB partition when it failed to finish updating due to insufficient space. I thought since I'd had some issues logging into it that I might have interrupted the first boot resize, so I re-imaged it, and loaded it up, left if five minutes, and then logged. No cigar... says it is still 1.4GB (1.4GB size, 1.2GB used, 2…

I am building kernel 5.10.4 sources on NanoPi Neo 2 with Armbian 20.11.10 Focal and get following error: nanopineo2:~:% cd /usr/src/linux-headers-5.10.4-sunxi64 nanopineo2:linux-headers-5.10.4-sunxi64:% sudo make headers_check nanopineo2:linux-headers-5.10.4-sunxi64:% sudo make scripts nanopineo2:linux-headers-5.10.4-sunxi64:% sudo make prepare scripts/Makefile.build:414: warning: overriding recipe for target 'modules.order' Makefile:1407: warning: ignoring old recipe for target 'modules.order' make[1]: *** No rule to make target 'arch/arm64/kernel/vdso/vdso.lds', needed by 'arch/arm64/kernel/vdso/vdso.so.dbg'. Stop. make: *** [arch/arm64/Makefile:182: vdso…

It's possible I may have uncovered a bug. I'm having a problem getting a remote share to mount on boot. The mount is attempted before the network interface is ready and I've got `_netdev` on the required line in `/etc/fstab` . . . . //192.168.0.160/raspi /zeus/raspi cifs rw,auto,uid=1001,gid=1002,file_mode=0755,dir_mode=0755,_netdev,vers=3,credentials=/etc/.smbcredentials_raspi_01 0 0 Here is the part of `dmesg` that explains the issue better than I can: [ 41.572110] sun7i-dwmac 1c50000.ethernet eth0: PHY [stmmac-0:01] driver [RTL8211E Gigabit Ethernet] (irq=POLL) [ 41.574888] sun7i-dwmac 1c50000.ethernet eth0: No Safety Features suppo…

Hi .. I am triying to use your new images of Debian wheezy and Ubuntu ones with my Cubietruck and vga output ... But i am not lucky !!! All starts ok , but suddenly no screen output , green ligth it is flashing but no monitor output (Black Screen ).. What is it the problem ? Thanks a lot ...

Hello, I'm trying to encode Video from the Orangepi gc2035 Camera to raw h264 with newest Armbian Xenial Kernel 3.4. I use a Orangepi One. For that I'm using the following gst Plugin: https://github.com/gtalusan/gst-plugin-cedar If I run the following gstreamer pipeline to get a raw h264 file it perfectly creates the file. But I can just play this file with ffplay. But not with vlc or broadway.js. Any idea how to get it playable in vlc and broadway.js? I've already tried to change to 66 to get baseline profile on following line and recompiled https://github.com/gtalusan/gst-plugin-cedar/blob/master/src/gstcedarh264enc.c#L296 But with no luck t…

Hello Still I could not resolve network problems with orange pi plus. My configuration: Orange pi plus with heatsink, (image Armbian_5.05_Orangepiplus_Debian_jessie_3.4.110), external USB drive(partition ext4). Main problem - when copying large file into samba share network hangs on orangepi board. CPU temperature not exceed 50C when copying. Leds blinking near ethernet cable but ping from cli works only on local ip. Same situation with other orange pi images (debian, lubuntu and ect...) Please help

Hi folks, I installed armbian with success on my orangepi zero. I was able to configure wifi and even fix some display issues on tv. But I am struggling to get a graphical manager running, I tried to start lightdm using: sudo start lightdm but I get "start command not found". any hints ? Thank you

Hi everyone, So far I'm using RPi2 and I would like to change to Orange Pi PC Plus or OrangePi Zero. I have questions: 1. Does OrangePi Zero share USB with LAN like RPi ??? 2. Can I install tvheadend on Armbian with OrangePi Zero? 3. Does OrangePi PC Plus share USB with LAN ? 4. Does RPi camera is compatibile with OrangePi slot?

i just upgrade from jessie to armbian stretch (5.65) i check aplay -l, why only shows audio codec? anybody help? root@bananapim2plus:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Codec [H3 Audio Codec], device 0: CDC PCM Codec-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0

Hi there, when I run command "sudo shutdown -r now" (or sudo reboot) my orange pi shuts down instead of reboot. Why this happens and how to correct it please? Thank you. My armbian: Linux orangepilite 3.4.113-sun8i #10 SMP PREEMPT Tue Jan 24 02:57:18 CET 2017 armv7l GNU/Linux

Hi! I use Cubietruck. I want to listen to music with its help. I have external DAC connected on SPDIF/Toslink. I establish on Cubietruck Armbian Wheezy Legacy kernel root@cubietruck:/home/setupini$ uname -a Linux cubietruck 3.4.109-sunxi #4 SMP PREEMPT Wed Sep 30 13:44:47 CEST 2015 armv7l GNU/Linux I have information that this distribution kit supports SPDIF: http://www.armbian.com/cubietruck/ http://www.cubieforums.com/index.php/topic,1275.0.html For audio I use MOCP On an analog output there is a sound, at the exit of SPDIF it isn't present. I learned that for work of an exit of SPDIF it is necessary to turn on 4 modules in a kernel: http://www.cubiefor…

Hello guys. I try to configure AP on WiFi. I have created /etc/hostapd/hostapd.conf: interface=wlan0 driver=nl80211 country_code=IN ssid=TEST hw_mode=g channel=6 wpa=2 wpa_passphrase=12345678 wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP auth_algs=1 macaddr_acl=0 Then I have uncommented DAEMON_CONF="/etc/hostapd/hostapd.conf" in /etc/default/hostapd. After it, I run /etc/init.d/hostapd restart And I try to scan WiFi via mobile phone, and no TEST. What am I doing wrong?

I have a nanoPi M1 with armbian Jessie, fresh install with no X server I wish to play a mp3 file using mplayer, but there is no audio output. #mplayer ./3951.mp3 the output is: MPlayer2 2.0-728-g2c378c7-4+b1 © 2000-2012 MPlayer Team Cannot open file '/root/.mplayer/input.conf': No such file or directory Failed to open /root/.mplayer/input.conf. Cannot open file '/etc/mplayer/input.conf': No such file or directory Failed to open /etc/mplayer/input.conf. Failed to read LIRC config file ~/.lircrc. Playing ./3951.mp3. Detected file format: MP2/3 (MPEG audio layer 2/3) (libavformat) [mp3 @ 0xb5d9b5b8]max_analyze_duration 5000000 reached [mp3 @ 0xb5d9b5b8]Estimating …

Hi all, First post here. I have been running Armbian on my original Bananapi Pro for a long while now, and thought that it's time to upgrade from Bullseye to Bookworm finally. There were some complications with UsrMerge that I had to resolve manually (I think some boot files from the original Buster installation were both in /lib and /usr/lib), but apart from that the upgrade appears to have worked: All userspace stuff is on Bookworm. # lsb_release -a No LSB modules are available. Distributor ID: Debian Description: Armbian 24.5.0-trunk.530 bookworm Release: 12 Codename: bookworm However, the kernel seems to be stuck on 5.15…

Hi. i tried to use g_ether module on legacy 3.4.112 kernel but without success. Could anyone help me? this is what i have when i run modprobe g_ether: [sw_udc]: [sw_usb_udc]: binding gadget driver 'g_ether' [sw_udc]: alloc request: ep(0xc0a8b7e8, ep0, 64), req(0xef3c8940) WRN:L2728(drivers/usb/sunxi_usb/udc/sw_udc.c):ERR: usb device is not active <4>g_ether gadget: using random self ethernet address <4>g_ether gadget: using random host ethernet address <6>usb0: MAC 5a:1d:b8:22:02:7f <6>usb0: HOST MAC 6e:49:95:27:67:f7 ep_matches, wrn: endpoint already claimed, ep(0xc0a8b834, 0xeeb62480, ep1-bulk) ep_matches, wrn: endpoint already cl…

wanted to make a system install to USB pendrive, but aborted it. Now it wont boot at all , but i managed to check out what may be the problem with the help of uart and the following came out: Gave up waiting for root device. Common problems: - Boot args (cat /proc/cmdline) - Check rootdelay= (did the system wait long enough?) - Check root= (did the system wait for the right device?) - Missing modules (cat /proc/modules; ls /dev) ALERT! UUID=e59363f1-765c-4660-9275-4563bb872371 does not exist. Dropping to a shell! Rebooting automatically due to panic= boot argument [ 69.860443] Restarting system. [ 69.863951] Restarting Linux…

I've a problem with latest Armbian Debian Server stretch (ARMBIAN 5.38 stable Debian GNU/Linux 9 (stretch) 4.14.18-sunxi, Uboot loader 2017.11) on OrangePI One, and OrangePI PC. It boots seemingly OK, but without any output to 1080P HDMI monitor. So I've no video. But Ubuntu Desktop with Legacy kernel boots fine using the same SDCard (and same power supply ). I can SSH to the Debian after boot, here's the boot and diag log. Couldn't wait for senseless SDCard testing to finish, as it works perfect with Armbian Ubuntu Desktop version. Legacy version on 1st boot shown boot progress and defaulted to 720P resolution, which I changed later to 1080P. But Debian Server doesn't sh…

I'm trying to load Armbian on my NanoPi R1, but it doesn't boot. I've been able to boot it successfully with https://www.friendlyarm.com/ official image, and also various (unsupported) DietPi images. I tried Armbian_21.02.3_Nanopi-r1_focal_current_5.10.21.img.xz using Balena Etcher to copy it to the SDCard on a Macbook laptop. Instead of seeing the uboot startup, the terminal remains completely empty. No idea where to start on debugging this. Please help! Thanks!

Hi, I've recently acquired some nanoPi M1, and just about now installed ARMBIAN. However I can't seem to get any sound working via 3.5 analog jack. Volume is set right on alsamixer Speaker are working and volume is set at max Soundcard is listed but yet I have absolutely no sound ... any ideas ? root@user:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: audiocodec [audiocodec], device 0: SUNXI-CODEC sndcodec-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: sndhdmi [sndhdmi], device 0: SUNXI-HDMIAUDIO sndhdmi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 root@user:~# cat /proc/asound/cards 0 [audiocodec ]: audiocodec -…

Hello, I am the owner of this board. I have some questions for developers 1. when will the reboot fix and what is the problem? 2 after last upgrading to 5.59.180904, armbian is no longer loaded at all. log the error: [ 2.319975] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.18 [ 2.328255] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.335488] usb usb5: Product: MUSB HDRC host driver [ 2.340462] usb usb5: Manufacturer: Linux 4.18.5-sunxi64 musb-hcd [ 2.346562] usb usb5: SerialNumber: musb-hdrc.1.auto [ 2.351855] hub 5-0:1.0: USB hub found [ 2.355641] hub 5-0:1.0: 1 port detected [ 2…

Hi Igor, nice idea to open this board i have a problem with my wireless connection using your jessie image with kernel 4.0.4 (newest release right now). at the first start i use a wired connection to connect via SSH - this works without any problems. Next step: configure wireless connection My /etc/network/interfaces looks like this: auto eth0 iface eth0 inet static address 192.168.178.150 netmask 255.255.255.0 # hwaddress ether # if you want to set MAC manually # pre-up /sbin/ifconfig eth0 mtu 3838 # setting MTU for DHCP, static just: mtu 3838 # # Wired adapter #2 #auto eth1 # iface eth1 inet dhcp # hwaddress ether # if you want to set MAC manually # …

Hello I'm using my Banana pi Pro as a domitic box with a Zwave Key connected on USB (aeotec Gen5) This morning, unfortunately, I made a apt-get Upgrade which updated the following packages armbian-firmware armbian-tools-jessie base-files bash ca-certificates dbus dbus-x11 e2fslibs e2fsprogs file fonts-opensymbol libc-bin libc-dev-bin libc6 libc6-dev libcairo-gobject2 libcairo2 libcomerr2 libdbus-1-3 libdbus-1-dev libgnutls-deb0-28 libgnutls-openssl27 libgudev-1.0-0 libhogweed2 libmagic1 libnettle4 libpam-modules libpam-modules-bin libpam-runtime libpam-systemd libpam0g libpng12-0 libpng12-dev libreoffice-base-core libreoffice-common lib…

Hi, I tryied a few times to run a RT kernel I built from https://github.com/igorpecovnik/lib as discribed in Armbian documentation and as in https://forum.armbian.com/index.php/topic/1950-orange-pi-pc-plus-armbian-guitarix-guitar-effectprocessor/page-2#entry16460. When executing compile.sh script it patch nice and good, then asks for Preemption Model and I chose 5 for Full Realtime. But when running the kernel into OrangePi it stucks in Starting Kernel. U-boot output: I am not choosing 1-4 for preemption model because I don't know if it will end up as an realtime kernel. The update from the older kernel to the rt one was done by dpkg -i on the deb files from the…

Hello, and thank you for your great work on Armbian. I have a BananaPi running on Armbian 5.38 Debian Stretch, downgraded to 5.31 due to freezing problems. i would love to use a 5" 800x480 HDMI connected "china"-Display with the BananaPi. Unfortunately it doesn't provide any EDID infos. I managed to set the resolution to 800x600 with an overscan_y=120 in boot.cmd, setenv video-mode sunxi:800x600-24@60,monitor=hdmi,hpd=0,edid=0,overscan_y=120 to see a approximately matching console screen. But the display is somehow not correct, wrong colors and no sharp characters. The only resolution with correct colors and sharp characters was…

Hello, I have installed MPD & ALSA (pulseaudio is removed) on CUBIETRUCK. Wtihin modules I added "sun4i_codec" & "sun4i_spdif" to get loaded. With "aplay -l" I only get: **** List of PLAYBACK Hardware Devices **** card 0: sun4icodec [sun4i-codec], device 0: CDC PCM Codec-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 LSMOD shows: Module Size Used by bnep 10570 2 hci_uart 17987 1 evdev 12164 1 ir_lirc_codec 4920 0 lirc_dev 8310 1 ir_lirc_codec sunxi_cir 3735 0 sun4i_ts 3990 0 nvmem_sunxi_sid 2159 0 nvm…

Well a little info, I've been using my orangepi one with an SDR dongle to track airplanes with flightradar24 for the last few months. My intentions were to use a POE adapter and run the board outside near the antenna at one point. I have now received the final parts and went to move it today. It has been running flawlessly for a month with my POE adapter off of a switch near my PC in my shop. I now plan on connecting it to the main switch on my LAN. So previously my setup was: Router -> switch -> long ethernet to shop -> swtich -> orangepione now I want to run it: Router -> switch -> long ethernet to outside -> orangepione But for some reason…

I have orange pi one with Armbian Xenial desktop legacy kernel 3.4.y which have a script.bin file in /boot directory and doesn't have /boot/dtb directory ...but when i installed Armbian Bionic mainline based kernel 4.19.y, I found the .dtb files but not the script.bin ....now i don't know how to configure both touch screen and the pwm pin! is the .dtb file (sun8i-h3-orangepi-one.dtb) is the same as script.bin or orangepione.bin ? if so, how to configure it? because i am used to convert the script.bin to .fex to configure it and then back to .bin.

Hi guys, I installed last armbian on Banana Pi M2+, and execute nand-sata-install.sh to boot armbian from emmc, it works fine. I want system boot from emmc, and storage some data to sd card, so I prepare one sd card with ntfs partition, insert to Banana Pi M2+, and boot. It cannot boot, and message are: U-Boot SPL 2016.05-armbian (Jun 23 2016 - 09:59:04) DRAM: 1024 MiB Trying to boot from MMC1 U-Boot 2016.05-armbian (Jun 23 2016 - 09:59:04 +0200) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi PC DRAM: 1 GiB MMC: SUNXI SD/MMC: 0 (SD), SUNXI SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial…

Hi, I have a orange pi pc plus, and i want to use a PN532 NFC module with Uart. At first, i need to enable uart and i have found this docs : https://docs.armbian.com/Hardware_Allwinner/ , but i think i miss something. My kernel version is 4.9.0, so i follow Vanilla kernel (Device Tree) explanations. What i understand is i need to modify "sun8i-h3-orangepi-pc-plus.dtb" in /boot/dtb. I try to do it, but i surely do something wrong, because my pi didn't boot anymore, so i flash the sd card. Before remaking any modification i prefer to be certain, do i really need to modify this files? And in particular this lines? /*Part of the files (Uart0 and Uart1)…

System: armbian, BananaPi Pro, sd card, sata ssd, usb hdd I manually moved my existing armbian system from sd card to a sata ssd. Then I changed the rootdev in armbianEnv.txt to the ssd´s UUID. After reboot I thought everything was ok. Then after a system update I figured out that the kernel version differs from the installed kernel modules. I think the new kernel and the modules are installed in /boot at /dev/sda whereas the kernel still boots from /dev/mmcblk0p1. How can I fix this? Here some information: root@pi-nas:/mnt/boot# lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT sda …

Tried both Debian and Ubuntu based 23.5 releases on my v1.4 board Boot process stops at "Starting kernel..." Also tried the "minimal CLI" debian release with same results. The previous versions 23.02 are fine. ▒ U-Boot SPL 2022.07-armbian (May 27 2023 - 19:26:49 +0000) DRAM: 512 MiB Trying to boot from MMC1 U-Boot 2022.07-armbian (May 27 2023 - 19:26:49 +0000) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi Zero DRAM: 512 MiB Core: 65 devices, 17 uclasses, devicetree: separate WDT: Not starting watchdog@1c20ca0 MMC: mmc@1c0f000: 0, mmc@1c10000: 1 Loading Environment from FAT... Unable to use mmc 0:1.…

In my Orange Pi One with ARMBIAN 5.27.170422 nightly Ubuntu 16.04.2 LTS 4.10.11-sun8i I install acpi: sudo apt-get install acpi And run sudo acpi_listen And nothing is show when I press the power button. Is normal or my button is damaged? Thanks

Hi everyone, I want to have a diskless Orange Pi Win, i'm trying to get the Ethernet to work in u-boot, but it does not seem to connect at all with my router when booting, no blinking led at all (none on the Pi neither on the router), I tried différents cables, ports, searched on the web, found some "patches" on DTS file on the web for pine64... But nothing seems to work (but Ethernet works correctly when the Pi is booted on Linux). Any Idea ? Many thanks,

Can the opi zero decode anything above 1080p? I want to decode a 3MP h.264 stream (2048*1538) and re-encode it to 1080p and serve over RTSP. do I need to get an H3 for that? the wiki says http://linux-sunxi.org/H2%2B#Variants Is that HDMI specific or lack of GPU power for decoding? Will that be pushing it too much even on an OPI PC?

Hi there! I've recently configured the ov5640 camera overlay and was able to capture videos either with mjpg-streamer of ffmpeg. Now on 6.1.34 both causes now a kernel oops. From the stack trace it looks like it happens inside v4l2 "media_pad_remote_pad_first" Unable to handle kernel NULL pointer dereference at virtual address 00000030 ... ... PC is at media_pad_remote_pad_first+0xa/0x58 I don't think v4l2 is the root cause because this may mean it fails alle the time which is unlikely. Looks like a null ptr gets passed in into media_pad_remote_pad_first ffmpeg used like this, but other parameters all resulting in the kernel oop…

Hi all, First of all, a big thanks for making Armbian work, the work you guys have done is incredible. I have a BPI M2+ board and I have a problem getting the serial communication to work both ways. I am using the latest image that is available to download on the Armbian website version 5.20, Jessie server, 3.4.112 kernel. According to the board fex file (found here) the configuration for the uart2 is: [uart2] uart_used = 1 uart_port = 2 uart_type = 4 uart_tx = port:PA00<2><1><default><default> uart_rx = port:PA01<2><1><default><default> uart_rts = port:PA02<2><1>&l…

Hi! Trying to setup HDMI audio on Banana Pi with Armbian Xenial mainline: root@bananapi:~# uname -a Linux bananapi 4.9.7-sunxi #1 SMP Thu Feb 2 01:52:06 CET 2017 armv7l armv7l armv7l GNU/Linux I tried adding Alsa config in /etc/asound.conf root@bananapi:~$ cat /etc/asound.conf pcm.!default { type hw card 1 device 0 } ctl.!default { type hw card 1 } root@bananapi:~$ speaker-test -twav -c2 speaker-test 1.1.0 Playback device is default Stream parameters are 48000Hz, S16_LE, 2 channels WAV file(s) Playback open error: -2,No such file or directory Any suggestions?

Hello guys, I'm just starting with bash scripts and the bananaPi, and I'm curious how the developers came up with the value of RAM usage, and why in the welcome script that loads when I login to SSH, the RAM usage is different from the command free -m ? I don;t really understand the line about memory_usage I just noticed the result is different from the free -m Thanks # memory and swap mem_info=$(LANG=en_US.UTF-8 free -w 2>/dev/null | grep "^Mem" || LANG=en_US.UTF-8 free | grep "^Mem") memory_usage=$(awk '{printf("%.0f",(($2-($4+$6+$7))/$2) * 100)}' <<<${mem_info}) memory_total=$(awk '{printf("%d",$2/1024)}' <<&l…

The essence of the problem is this. I work with Orange PC Plus microcomputers. I used to use the Armbian_5.25_Orangepipcplus_Ubuntu_xenial_default_3.4.113 distribution And so the device address was HW Address: fa: 20: 6d: b5: 65: bd But when installing new distros Armbian MAC becomes different. HW Address: 12: 81: ab: 1a: 39: 92 Permanennt HW Address: 12: 81: ab: 1a: 39: 92 I really need the MAC to be like before. And it did not change when reinstalling the OS. How to do it?

So I have a nanopi m1 and a neo. I'm running Ubuntu Xenial on them: https://www.armbian.com/nanopi-neo/ I'm attempting to access the gpio, when I attempt to echo to /sys/class/gpio/export I get permission denied (sudo or not, even if logged in as root). I've also found this library for python to handle gpio on the nanopi: https://github.com/jrspruitt/FriendlyARM_Python_GPIO But when I use it, it says: as root root@nanopineo:/home/admin# python test.py Traceback (most recent call last): File "test.py", line 7, in <module> gpio.gpio_init(16, 1) File "build/bdist.linux-armv7l/egg/fgpio/fgpio.py", line 85, in gpio_init File "build/…

Hello, I am using the Armbian_5.38_Orangepizero_Debian_stretch_next_4.14.14 image on an OPi zero (H2+ chip). I tried to get "some sound" out of the LINEOUTL and right pins at the expansion port. However, alsa executables like aplay report that there is no sound card. (see below) I testet also with a non-root user (which is in the audio group). My initial guess was that there must some additioanl kernel modules loaded. As I understand, however, the lsmod output, (2) below, should be ok. What it is thing to do to see soundcard(s), e.g. as /dev/dsp? Do I need to set files such as ~/.asoundrc or /etc/asound.conf as a prereq…

How to enable kvm/virtualisation on orange pi 3 lts? I want run windows for arm on qemu with kvm, but in the kernel there is no kvm module . How i can add this module to kernel? I know that the allwinner h6 has support for virtualisation.

Hello All, I have configured OrangePiR1 as router. There are three network interfaces, two as wired and one wifi(hotspot). eth0 serve for access to internet(via ppp/adsl) and eth1+Wlan0 for internal network. Interfaces eth1 and wlan0 are in bridge br0. Problem is, that interface eth1 sometimes loses connection/link(cable and switch were checked ). Next nonstandard behavior of eth1 is, that only yellow led control is blinking, while green led control is not alight. Network interfaces were configured via file /etc/network/interfaces. However, when I checked network manager nmcli, I saw, that some connections are configured there too (there can …

Never had a problem with Armbian on my board. After last full upgrade (linux-image-next-sunxi 5.27.170427 etc) system is not booting. I tried with a fresh SD card (image Armbian_5.25_Cubieboard_Debian_jessie_next_4.9.7) - it's booting fine afresh, but also doesn't boot after full upgrade. Below are logs for both cases. Boot with old card: Spoiler U-Boot 2017.01-armbian (Feb 02 2017 - 02:20:16 +0100) Allwinner Technology CPU: Allwinner A10 (SUN4I) Model: Cubietech Cubieboard I2C: ready DRAM: 1 GiB MMC: SUNXI SD/MMC: 0 *** Warning - bad CRC, using default environment In: serial Out: …

Please give me a tip - what is purpose of /dev/mmcblk2boot block devices created? Quite small size - 4MB - ones, do they serve to something u-boot needs at boot time? There are no records for them in fstab so I assume they are created by zram, but what happens to them after boot when they aren't needed anymore? Board Orangepi 3LTS with bookworm minimal Also as a matter of wondering - why there are two zram devices: one of 1/2 of RAM (as usual) and another of quite small 50MB only, what is it for? root@heaven:~# fdisk -l <redacted> Disk /dev/mmcblk2boot0: 4 MiB, 4194304 bytes, 8192 sectors Units: sectors of 1 * 512 = 512 byt…

We try to set up lirc on opi pc, but only receive works fine, any idea how to set it up to work in both modes - transmit and receive?

Hey there, I am a long time user of your armbian operating system. It is great, I am using it for a simple home NAS system. But I have found one problem with armbian, which is very annoying: My standard Banana Pi keeps loosing the HDD Ive connected over Sata. It is a 3,5" Seagate Barracude 3TB drive formated as Ext4. It gets 5V and 12V power and runs quite perfect, as long as it has something to do. It spins up and down as I configured it. But when I leave the pi for a longer time period unattended (no workload), and the harddrive stays in spindown-mode too long, it wont identify the HDD anymore. The mount point and the /dev/sda are gone. I need to powercycle t…

I've tried to connect 5" TFT monitor to OPI with no luck. Cable pinout : T (Left audio) R (right audio) R (video) S (Ground) boot image: Armbian_5.20 scripr.bin section [boot_disp] advert_disp = 0 auto_hpd = 1 output_type = 4 hdmi_channel = 0 hdmi_mode = 4 cvbs_channel = 1 cvbs_mode = 11 output_full = 1 hdmi_mode_check = 1 [disp_init] disp_init_enable = 1 disp_mode = 0 screen0_output_type = 2 screen0_output_mode = 14 screen1_output_type = 2 screen1_output_mode = 14 fb0_format = 0 fb0_width = 0 fb0_height = 0 fb1_format = 0 fb1_width = 0 fb1_height = 0 [hdmi_para] hdmi_used = 1 hdmi_power = "vcc-hdmi-18" [tv_para] tv_used = 0 tv_dac_used = 1 tv_dac_src0 = 0 and…

Hi, First of all sorry for my bad English. I am trying play video on my OrangePi Zero2+ H3 and 7inch waveshare touch screen. I couldn't get the touch screen work with Armbian 5.38 - 3.xx kernel. (I downloaded the Armbian Xenial desktop legacy kernel 3.4.y from website. In this version, mpv plays video with hardware acceleration) Then I updated to Armbian 5.44 - 4.xx kernel (I downloaded the Armbian Stretch mainline kernel 4.14.y from website.) then 7inch touch screen started to work but this time no hardware acceleration. It works "mpv vid.mp4" with dropped frames and very high CPU usage. But it gives error when I try to start video with "mpv --vo=…

I install Jessie server armbian on orange pi and install wiring op on it from this link https://github.com/zhaolei/WiringOP and for test interrupt I use this example form https://github.com/ngs/wiringPi/blob/master/examples/isr.c as he said for test use gpio mode 0 up gpio mode 0 down in terminal , I did this and it just print waiting... my question is , Is wiringPiISR working on orange pi one? If the answer is yes, what should happen in this example? If the answer is no ,what can use instead of wiringPiISR ?