Allwinner sunxi

Good day. My trouble - is not started spi, on orange pi pc, with ARMBIAN 5.25 stable Ubuntu 16.04.2 LTS 4.10.0-sun8i I read documentation for DTB overlays on official site https://docs.armbian.com/Hardware_Allwinner_overlays/ Check armbianEnv.txt, edit DTB (dts) sun8i-h3-orangepi-pc.dts And change status from "disabled" to "okay spi@01c68000 { ...... status = "okay"; ....... This is my /boot/armbianEnv.txt verbosity=1 console=serial overlay_prefix=sun8i-h3 overlays=w1-gpio spi-spidev param_spidev_spi_bus=0 But SPI not started This is boot log h…

Hi, i am using orangepi PC (H3). i had tried follow link, test.mp4 file created successfully. (video fine). https://github.com/avafinger/ffmpeg_cedrus264_H3 now, i want to real time(20~30 fps) capture for /dev/video0 (gc2035). i tried mpv with gc2035, but it didn't worked. i want real time video capture using cedrus264. orangepi@OrangePI:~/tmp$ mpv tv:// Playing: tv:// [tv] Selected driver: v4l2 [tv] name: Video 4 Linux 2 input [tv] v4l2: your device driver does not support VIDIOC_G_STD ioctl, VIDIOC_G_PARM was used instead. [tv] Selected device: sunxi-vfe [tv] Capabilities: video capture read/write streaming […

Hello there, I am looking for some feedback/suggestion about an issue I have. Installed Armbian legacy kernel just yesterday. Then I have plugged https://www.olimex.com/Products/USB-Modules/MOD-WIFI-AR9271-ANT/ to enable wifi and found out I missed required firmware. I installed such firmware (htc_9271.fw) first by Ubuntu linux-firmware package, then tried with armbian-firmware-full, then I have downloaded from here http://linuxwireless.org/download/htc_fw/1.3/ (putting in /lib/firmware and after failing tried also /lib/firmware/ath9k_htc like package manager does. I have also tried compiling my own version from here https://github.com/qca/open-ath…

Hi all, Recently i bought a orange pi +2E . I want to display it on a 2K display. with specs 2560x1440 resolution. https://www.alibaba.com/product-detail/New-5-5-LS055R1SX04-2K-1440_60694188895.html?spm=a2700.7724838.2017115.428.5a541062gAX23i I bought this board as it supports resolution upto 4K. But i failed to interface it with 2K. I m using armbian OS. I tried most of the modes in h3disp. Can anyone help me please . Thanks in advance

My Pi Zero with H2+ and latest Armbian 5.35 Xenial works well, but on trying to increase the screen size I get: dk@desktop:~$ ssh dk@zero dk@zero:~$ sudo h3disp -m 1080p60 Unsupported board/kernel combination: Orange Pi Zero running 3.4.113-sun8i dk@zero:~$ Is this going to be fixed? nomachine.com's remote desktop for ARM works brilliantly Ubuntu + citadel-suite gets a mail server/chat server/+other into 337 MB - amazing!

Hi everybody, burned the latest armbian for opi prime since I got the board, and the greed led is working, but after all I cannot find it with “arp -a” and the ethernet led is flash, both color. Anyone have the idea? I don't have a screen or tv even a router here course I am at university. So I directly connected my computer with the board. Don't think anything is wrong.

Hi i have a problem trying to load the drivers of this camera, could you help me? Issue: mobprobe: FATAL: Module ov5647 not found in directory /lib/modules/4.14.84-sunix Board: Orange Pi Lite Camera sensor: OV5647 fisheye OS: Ubuntu - Armbian 5.65

Orange pi one refuse to add spi to /dev/. It's 5.73 armbian kernel 4.19.20-sunxi. I've activated spi dev from armbian-config but no device after reboot. Gpio and i2c work great . Anyone had problem like this? Послато са Redmi Note 6 Pro уз помоћ Тапатока

So I did the following today: Spoiler sed -i /deb/s/jessie/stretch/g /etc/apt/sources.list $ sed -i /deb/s/jessie/stretch/g /etc/apt/sources.list.d/*.list apt-get update apt-get upgrade apt-get dist-upgrade Everything went fine except at the end where it complained about busybox not being there and it failed the update of initramfs... This was no issue. I installed busybox, rebooted, ran apt-get autoremove and then autoclean and everything worked fine. I was still on kernel 3.x, so I ran armbian-config but I did not see the latest kernel present in the switch kernel option. I ran apt-get install linux-image.next.sunxi (or some…

I have read two old threads in this forum: I have been running this (will post more details if needed) for a few days: VERSION=5.90 DISTRIB_ID=Ubuntu DISTRIB_RELEASE=18.04 DISTRIB_CODENAME=bionic DISTRIB_DESCRIPTION="Ubuntu 18.04.3 LTS" NAME="Ubuntu" VERSION="18.04.3 LTS (Bionic Beaver)" Kernel is 4.19.62-sunxi The BPi would hang/freeze, seemingly randomly within a day or two. When it does that, there is no HDMI video or response to ping. After reading the first thread, I did stress test on the BPi for more than 2 days. The BPi actually hold up. So, next I ran "ping -i 30 -D 192.168.8.1" -- pinging …

Hello guys, I am experiencing such a problem: When I boot my orangepi it starts and it is visible in the router's page view getting IP with dhcp. As soon as I connect over ssh (at least this is the way to trigger it, not sure if it is hapening automatically after a while), the device disappears from the network and it is no more available! I have seen this behaviour happening on 2 different routers. Then I rebooted the device again and in the router config I put the same IP statically linked to the device and I tried to connect over ssh and it worked without disappearing anymore. So it sounds like a bug somewhere using dhcp protocol. Is som…

Hello, I have a Orange Pi One Plus and i install Armbian image but the ethernet doesnt work. I dont know how fix it. I have search on other post but i cant resolve it. Thanks for your replies!

Hi! I use this board since jun/2019 with Armbian 5.90 and kernel 5.1.15 (all OK except HDMI audio). In these 6 months tried to update kernel image few times, 5.2.x some months ago and now 5.5.0, but not more 1920x1080 support, the maximum is 1280x1024. Xrandr not show as supported mode anymore, whats happen? This is related to u-boot? I think can not read EDID, because no monitor model name is shown. Another question is, now in 5.5.x I can see HDMI audio device, but still can't listen, what left to be developed?

Hello, I have a GPIO pin that is high when starting the board. I am trying to force it low. Taking a look at gpio readall +-----+-----+---------+------+---+---Pi ?---+---+------+---------+-----+-----+ | BCM | wPi | Name | Mode | V | Physical | V | Mode | Name | wPi | BCM | +-----+-----+---------+------+---+----++----+---+------+---------+-----+-----+ | | | 3.3v | | | 1 || 2 | | | 5v | | | | 12 | 8 | SDA.1 | ALT5 | 0 | 3 || 4 | | | 5v | | | | 11 | 9 | SCL.1 | ALT5 | 0 | 5 || 6 | | | 0v | | | | 6 | 7 | GPIO. 7 | ALT3 | 0 | 7 || 8 …

I'm a newbie. Got the NanoPi R1 that sports a UART but no Video Output. Now when I want to read the output of the serial console I need a 3-wire cable and a converter, that much I know. But what is the baud rate? Where is this configured on the armbian NanoPiR1 image (on my raspberry Pi I just checked and found the file /boot/cmdline.txt with that settings, in my case it's 115200) Why is the baud rate nowhere documented? On the download page https://www.armbian.com/nanopi-r1/ it is stated that "serial console is enabled on UART1, which is exposed on chasis" , but no hint about which speed to use. There neither is any info about the baud rate on…

I'm connecting my Orange PI PC 3.5mm jack to this power amp: HiLetgo 5pcs PAM8403 2x 3W Mini Digital Power Amplifier Board AMP Class D 2.5-5V Input If I connect a 5v 2a power supply to the amp and a 3a 5v power supply to the Orange PI PC, it sounds great with no noise form the Orange PI and no distortion from the amp power supply. If I try to run the amp from the 5v pins on the Orange PI PC with the 3amp 5v supply, it will work, but there is a lot of noise from the main board and the amp does not get enough power to run properly. Should 3a be enough to run both these peripherals? I think the power amp will pull about 600ma, not sure what the Orange PI…

I just discovered that /usr/bin/su in my Armbian: v26.2.1 for Orange Pi PC running Armbian Linux 6.12.58-current-sunxi is a x86_64 binary: $ ls -l /usr/bin/su -rwsr-xr-x 1 root root 50800 Mar 6 13:10 /usr/bin/su $ file /usr/bin/su /usr/bin/su: setuid ELF 64-bit LSB executable, x86-64, version 1 (SYSV), statically linked, no section header I installed the rust version, su-rs, but I thought it would be useful to warn about this. I checked /usr/bin and /usr/sbin and this is the only x86-64 executable.

I obtain an "Authentication token manipulation error" on Banana Pro Debian 3.0 jessie 4.0.4 when I try to change the rot password in the first run. Any help? Thanks

On a Banana PRO with Debian Jessie I installed the lightweight desktop and all is more or less usable except the web browsing. I been using Iceweasel and Epiphany Browser (I can find Midori on the included repositories) but are completely unusable. I suppose that images are using the philosophy of "Disabled all memory reservations for GPU" Is a problem about the dedicated RAM to the graphics engine? How I can change this memory split? Thanks in advance.

I am a relatively new Linux user and I currently have a orange pi PC. There are some games not in the official repository I would like to compile. When I do so could I add them to the repository here?

Hello I have a little problem with the usb devices, i use usb camera and if u plug the power supply to the OPI Lite board (5.25) it recognize the camera but it doesn't work well (stream with like 8-10 fps), after a software reboot, the device go to other Bus and the camera work fine with 15-30 fps stream. Before reboot, exact on first power of the board: Bus 006 Device 002: ID 058f:3822 Alcor Micro Corp. Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 002: ID 0bda:8176 Realtek Semiconductor Corp. RTL8188CUS 802.11n…

Hello, My project for Orange Pi Lite will be used in a car. To make the installation easy for everyone I would like to supply it from car lighter socket. Of course, this solution is not perfect (frequent insert/pull the plug by the user, current decays etc.). I mean problems with switching off without shutdown. I also mean how uSD will stand it. For now, I thing to attach an 18650 cell with booster/charger which will work as a "buffer" to keep current when the lighter socket is off. But I am afraid that it can keep power only for 1-2 hour. Is there a possibility to check the power level of the connected cell and shut down the system when the power is low? P…

I received today my BPI M2+, however, I cannot make it boot. I tried both Diet Pi and Armbian Server. No boot. The red LED is on all the time. I'm using a Samsung EVO 32 GB SD card flashed with Etcher on Ubuntu. My power supply is a 5v 3A barrel connector. Since the usual suspects are not the cause, I have no idea what might be going wrong.

FYI & FWIW: Howto find your NanoPi NEO2 Your NanoPi NEO2 is connected to your LAN, but how to find it? What is the IP address? Here are my methods: Via bonjour (Ubuntu to Ubuntu): ssh nanopineo2.local. Example: $ ssh nanopineo2.local. sander@nanopineo2.local.'s password: _ _ ____ _ _ _ ____ | \ | | __ _ _ __ ___ | _ \(_) | \ | | ___ ___ |___ \ | \| |/ _` | '_ \ / _ \| |_) | | | \| |/ _ \/ _ \ __) | | |\ | (_| | | | | (_) | __/| | | |\ | __/ (_) | / __/ |_| \_|\__,_|_| |_|\___/|_| |_| |_| \_|\___|\___/ |_____| …

Hi guys, Quick question about the USB ports on the Cubietruck. Once I am done with the usual setup procedure (changing the root password and setup a user) system reboot. I sometimes end up in situations where I need to access the Cubietruck directly and not through ssh. In such situations I noticed that my usb keyboard and mouse do not respond at all, eventhough if these are the exact same ones hich I used to the 1first time setup. What could be the reason for this ? Thx,blub4747

Hi , sorry for my english guys after Update /Upgrade to armbian 5.38 , my sytem did not rebooting anymore , before it was Fine for Long Time with Reboot Every Night I have not so mutch Experience with Linux i hope Same one can give me a hand, Best is a Step by step List I‘m connected directly to The Board via hdmi, i did not have a Network cable conected at Moment Because i‘m not at Home and i took The cubitruck with me to My workplace 2 pictures : https://picload.org/view/dagwdolr/fd49eb8f-23bb-4b4d-9763-e9bd87.jpg.html https://picload.org/view/dagwdola/6f5eea…

Is there a plan for supporting the "NanoPi Duo2" from"friendlyarm" in the future? http://wiki.friendlyarm.com/wiki/index.php/NanoPi_Duo2

Orange Pi Zero Plus2 H5 I currently am booting from the onboard 8GB EMMC. As I am still experimenting with this board, sometimes I would like to wipe and start from a backup remotely, keeping a copy of my backup on an SD card that's in the machine used for extra storage space. I use timeshift on my Mint laptop that restores a snapshot of / from an SDcard, but it is a graphical utility. Is there a similar CLI utility for Armbian? Or one that can be installed? Thanks.

Hi, I am fairly new to the SBC board and struggling to begin my setup of the NanoPo NEO Air. This little board is a perfect fit for my project I need to develop. The first problem I encounter is the following: There are no HDMI port. Thus I can't do the basic configuration for my network and allow an SSID access. Does anyone has a solution to preconfigure the WIFI of my Armbian from windows (or Linux if needed)? My second problem will be: I would like to install my system on the EMMC flash to not be dependent of the SD card. Can you confirm I would only need to run the command "nand-sata-install" when I will get…

On a fresh install of Armbian 20.08.1/Linux 5.8.5-sunxi on an OPi Zero (256MB version), total memory is 238MB according to "free -m": root@orangepizero:~# free -m total used free shared buff/cache available Mem: 238 74 78 1 85 154 Swap: 119 0 119 238MB is not 256MB. :-) I assume the discrepancy is due to reserved framebuffer memory, but after a bit of testing I've found that the "sunxi_fb_mem_reserve" parameter (set to "16" in /boot/boot.cmd by default) has no apparent effect. Here's a boot with the Armbian default "sunxi_fb_m…

I am having problems with ethernet, the sbc was connected to 100 mbps network and it worked normally, but recently i relocated it and connected it to another cable, the problem is that now i only get 10mbps, the cable is ok because it tried in my pc and got 100mbps, but i only get 10mbps on the sbc, then i found how to fix this in settings, but i acidentally removed ethernet connection that i was using and now the ethernet doesn't work, do i have to change something in network interfaces? also it says no link detected

I'm running my Orange Pi Zero headless on Armbian Buster 20.11.6 Last check uptime was 6 days, but now I find its rebooted and I think this is due to unattended security packe upgrades. The package is installed unattended-upgrades/stable,now 1.11.2 all [installed] automatic installation of security upgrades Looking in /etc/apt/apt.conf.d 01autoremove 20auto-upgrades 70debconf 01autoremove-kernels 50apt-file.conf 71-armbian-no-recommends 02-armbian-compress-indexes 50command-not-found 81-armbian-no-languages 02-armbian-periodic 50unattended-upgrades Is…

How I solve this problem or is it an Ambrian bug? Maybe a better question is what is causing these repeated messages. I am at a loss to finding a solution. BOARD=bananapipro BOARD_NAME="Banana Pi Pro" BOARDFAMILY=sun7i Spoiler --< CUT >-- [ 50.900954] ieee80211 phy0: brcmf_fweh_call_event_handler: no interface object [ 50.900982] ieee80211 phy0: brcmf_fweh_event_worker: event handler failed (72) [ 50.976400] ieee80211 phy0: brcmf_fweh_call_event_handler: no interface object [ 50.976437] ieee80211 phy0: brcmf_fweh_event_worker: event handler failed (72) [ 51.025829] ieee80211 phy0: brcmf_fweh_ca…

I used python script with Orange pi zero 3 (Armbian_community_24.8.0-trunk.6_Orangepizero3_bookworm_current_6.6.31_minimal.img) Observation: 1) /dev/ttyS1 is actually Serial 2 as per pin diagram as per Orange Pi Zero 3 - Armbian web page 2) /dev/ttyS2 is actually Serial 5 as per pin diagram as per Orange Pi Zero 3 - Armbian web page 3) even if I set rtscts=True in crateing object ser in above script, there is no output on rts or cts pin. I am looking forward to have RTS pin remain high during transmission to easily integrate ic for RS485 communication. I was glad that Amrbian for Orange Pi Zero 3 has out of the box RTS CTS pin suppor…

hi can somebody fix repostiory install list error for chromium as chrome-commen and chromedriver wont install problem: chromium/noble 9:126.0.6478.182-1~deb12u1+narmbian1 arm64 web browser installs with version therefore chromium-common and chromium-driver,will not install because its looking for dependency chromium 126.0.6478.182-1~deb12u1+n1 Without the ":9" i presume he following packages have unmet dependencies: chromium-driver : Depends: chromium (= 126.0.6478.182-1~deb12u1+n) E: Unable to correct problems, you have held broken packages. please can somebody fix

Just installed Armbian 25.5.1 Desktop in my new board: Orange Pi Zero 3 with 2GB RAM, using a 32GB MicroSD card. Installed desktop as I have HDMI output and wanted to check that everything was going fine, and it did. I can connect to Armbian via SSH I could set up Pi-hole correctly. (that's why I get the board for) As My modem/router cannot manually set the DNS to the IP of the orange pi, I just disabled it ans installed ISC-DHCP server and got it running. I used chatgpt for that purpose. I have some understaning using linux distros and networking, chatgpt just saved my some time with configuration. After some days I saw o nInternet t…

Hi, I've tried to set up my new cubietruck with Igor's Debian-3.8-wheezy-4.0.4 image but first, it can't bring up eth0 and then gets stuck at restarting sshd. Tried rebooting and powercycling 4-5 times, always the same... Any ideas? Or should I use another image or kernel? If yes, which one? Many thanks and best regards, cibomato

Update: checking download file, it seems that I downloaded Armbian_4.5_Cubieboard2_Debian_jessie_4.2.3.zip so it's not 4.81 no matter what the download pages said. I'm trying to install upstream kernel on Cubieboard 2 and kernel never starts. Attached is output from boot (I'm getting same on serial port). I did try different sdcard (to rule out problems with it) but I'm worried about ext4fs_devread read error and partition error. Is there something more that I can try? Legacy kernel works well, but I wasn't able to just upgrade kernel and u-boot on it, but that resulted in unbootable system -- which packages I have to install to migrate from legacy to upst…

Somehow I manage to get online on this system . Updated a few files .Wow it is getting interesting . I think this network manager inbuild is pathetic . The system only reads from the terminal. Anyway android is the only way to get net into this system.Well of course I have to figure out a bit , stay up some nights. I have myself why keyboard gave wrong keys. it is very usable now except that it needs some gpu acceleration, and more of a GUI presentaion.My HD display needs some good video rendering .Anyone, tell me how to copy paste in terminal, also I kept my screen at 1080p , I think it is not appropiate.Text in terminal are so small. OK for tether…

Hi, I am running headless mainline jessie image on my cubietruck smoothly for some months now. The only drawback is that i need from time to time to play some videos on the tv. I have been waiting for hardware video acceleration in order to install mpv and play videos without GUI. I have been looking at the sunxi mainline effort and I see that for kernel 4.8 they plan the display engine clocks (TCON, FE, DE). As I am not a developer, it is not obvious to me (I have already googled it but no luck) if the display engine clocks are what we are waiting for hardware video acceleration on the mainline kernel. Can someone please explain (this noob question) what are displa…

Hi guys, I'm trying to solve a very specific problem in our company and after reading several tutorials I'm still not sure, how to achieve my goal. It would nice, if anyone can share his code or help me, however I will also to try to finish it and post the solution here. Idea/Issue: We've upgraded a very old cutting machine with plasma cutter, however there is only a USB port on the device, therefore our colleagues have to go several times per day from office to workshop and swap flashdrives. Thanks to size of our plant this isn't very good solution. Idea is to take Orange Pi One and connect it to the machine through OTG port, therefore it will act as Flashdrive. Th…

Hi guys, I bought the orange zero and then I realized how poor wifi. I had some wifi modules from old tablets at home, they are rlt8188eu. After I joined the orange, there was another problem. Wifi driver could not be initialized, because I knew that these modules can operate on orange pc out of box, I began to research the problem. Cause I am linux ZERO, it took me longer time, but I finally found soulution. Problem was in fex file for orange zero, wifi_usbc_type = it´s without parameter, after I added some parameter ( "5" from working orange pc fex), wifi work like a charm. I´m not sure if it´s purpose, or bug, so I write you....

hi all i'm trying to boot my orange pi over the network. i have written u-boot into SPI-Flash memory. i modified boot.cmd script to download the kernel, init ram and script.bin from TFTP server. after downloading them all the kernel tries to start but it dose not proceed. I've attached the screenshot of the console. My boot.cmd Spoiler # DO NOT EDIT THIS FILE # # Please edit /boot/armbianEnv.txt to set supported parameters # setenv serverip 172.20.20.200 setenv load_addr "0x44000000" setenv overlay_error "false" # default values setenv rootdev "/dev/nfs" setenv verbosity "1" setenv console "both" setenv disp_mem_reser…

Hi, It's been a while that I'm trying to activate the AP of the OP Zero 2+ but in vain. I already succeded activating it on the OP Light using hostapd.conf and interfaces.conf, but when I tried the exact same configuration on OP Zero 2+ the AP didn't work. I tried a lot of solutions found in the internet, but none of them seem to work. Please any help would appreciated !

How enable UART1 (pin 8 and pin 10) or UART2 (pin 11 and pin 13) I re-read a lot of documentation but did not find a solution, everyone writes abstractly. There is a concrete decision how to include it for orange pi (zero or one) and armbian. Correctly I understand that UART1 is ttyS1 and UART2 is ttyS2?????? p.s. Help, I'm ready to even pay for help ) uname -a Linux orangepizero 4.11.5-sun8i #11 SMP Fri Jun 23 20:03:23 CEST 2017 armv7l GNU/Linux

The pcduino discussions appear to be centred here and the A10 appears to be a cutdown A20 so please forgive me if this is in the wrong area. I've been playing with an old pcduino2 and have got the latest mainline server version of Armbian installed on it. Very impressive. However, it appears to have only a single I2C bus and no SPI devices. It looks like there should be a sun4i-a10-spi-spidev.dts file somewhere or else some way to build the appropriate kernel modules but I have been unable to find this. I understand that this is a deprecated board but I should (hopefully) be able to perform any kernel builds required and am more than happy to feed the resul…

I have an orange pi light I loaded two sd, one 16GB and one 32GB with "Armbian_5.35_Orangepilite_Ubuntu_xenial_default_3.4.113_desktop.img" I can not see any mistakes in the console: https://pastebin.com/HXyeQkjr I tried various resolutions. Still, the screen remains red and nothing appears.

I built Armbian_5.59_Nanopineocore2_Ubuntu_xenial_next_4.17.17.img for my board, and am trying to add an overlay dtb that describes a port expander I have on i2c2. $ sudo armbian-add-overlay ./mcp23008.dts Error: dtc does not support compiling overlays Please try to install matching kernel headers

RTL8211D PHY on OrangePi Prime is not detected neigther in uBoot mode or Kernel mode. Will share the logs ASAP. Please suggest!

Hello folks, I'm having trouble booting to Armbian. The green LED turns on, and the LAN lights work, but outputting to HDMI always ends in no signal. I have tried: - Using official Orange Pi operating systems, they work, but are unstable. - Using f3 to check if my SD card is corrupted/fake. Returns working. - Using different power bricks, will still turn on leds, but not output to HDMI - Using different Armbian kernels, no success Any ideas lads?

I was updating some images and thought the Orange Pi + had been retired ... but there was no Support Ended note. I see a lot of other Plus versions of Orange pi boards listed, but not the plain Orange Pi +. Seems easy to miss ;] A little searching found the Orange Pi + is supported https://www.armbian.com/orange-pi-plus/ Am I just missing the link in Downloads? The only way I've been able to get to the page is by direct url or a duckduckgo search https://duckduckgo.com/?q="orange+pi+plus"+armbian&t=raspberrypi&ia=web

After having my old debian (wheezy? or jessy?) unbootable from systemd update I decided to clean install. Having gotten a good Power supply, an A1 Speed 10 SD card, etcher image, and armbian debian 20.08 (also tried 20.07), The board boots (Welcome to armbian) up to "network interfaces up) - then the screen goes blank/black, and I get the green led heardbeat (slow blinking) for a while. Pushing power again the board shuts down (green LED blinking rapidly for a moment, then red power LED comes off). I have had installed boot to nand / Sata disk before but all that shouldn't matter I think because the boot from SD Card seems successful - why could it be th…

Orange Pi Zero 512 MB has a serious wifi problem. After i connect the wifi network, i loose connection and i can't access my zero until i connect with ethernet cable. Interestingly, after i connect ethernet cable, wifi reconnects. i set up my wifi connection with nmtui. Auto connect enabled. I really need to solve this wifi issue. In my thinking there two options, which one is better i don't know. 1 st option: I have to buy wifi adaptor, but i don't know will it solve the problem. (and probably i am going to have driver problem) 2nd option: I am going to write a new thread with python. This code will check wifi connection every 10 seconds, if …

Hi, I tested my board with below armbian distro. Question is , there are lots of entry about H3 hw decode problems, are these fixed in this distro? When i open 1080p mp4 Big Buck Bunny video still doesnt work is that any specific settings to work with hw accelerated decode. How can i be sure that hw decoding is running with VLC? or any specific ffmpeg command. Linux orangepipc 5.10.60-sunxi #21.08.1 SMP Wed Aug 25 18:19:32 UTC 2021 armv7l armv7l armv7l GNU/Linux I tested video with - VLC using 55% cpu - MPV using 40% cpu Umit

Hi, i need to download version Armbian 21.05.6 Buster with Linux 5.10.43-sunxi , is it possible to do it now and how? thank you

Hello, I've issue with nameserver. My router DHCP DNS server point to the Pi which has IP 10.6.6.3. But for unknown reason 1.0.0.1 keep added in the /etc/resolv.conf: # This is /run/systemd/resolve/resolv.conf managed by man:systemd-resolved(8). # Do not edit. # # This file might be symlinked as /etc/resolv.conf. If you're looking at # /etc/resolv.conf and seeing this text, you have followed the symlink. # # This is a dynamic resolv.conf file for connecting local clients directly to # all known uplink DNS servers. This file lists all configured search domains. # # Third party programs should typically not access this file directly, but only # through the symlink a…

I am trtying to keep my pcduino 3 nano alive. It has been working perfectly under a debian bullseye distro from Johan Gunarsson for 4 years and now I can't get the OTG to work under any release (bullseye, bookworm or trixie) I have explored many avenues, but even a plain manual setup of g_mass_storage doesn't work in a workable way. The drive appears in Windows Explorer after several minutes, and any copy or delete to that gadget drive takes ages (3+ minutes for a 12kb file) before it fails or succeeds silently. I am looking for a forum where pcduino users can help each other. Thank you, Gaetano.

Dear All Have anybody tried and connected the following screen to Orange PI under armbian? If so, could I please ask any instructions? http://www.aliexpress.com/item/Orange-Pi-7-inch-LVDS-LCD-Module-7-Touch-Screen-F-Raspberry-Pi-Car-GPS/32315435767.html

Hi, yesterday I moved my root partition to a 128GB SSD by running "nand-sata-install" Everything works fine. Now I got a SD-Card in my Banana Pi with one big partition: fdisk -l Disk /dev/sda: 128.0 GB, 128035676160 bytes 30 heads, 63 sectors/track, 132312 cylinders, total 250069680 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x93d6d043 Device Boot Start End Blocks Id System /dev/sda1 2048 250069679 125033816 83 Linux Disk /dev/mmcblk0: 3965 MB, 3965190144 bytes 46 heads, 9 sectors/track, 18706 …

Hello I'm investigating update from wheezy to trusty on my OrangePI (A20) based home media server. I'm using custom kernel 3.4.110 with SATA multiplier support. System is on HDD. I had few remarks and issues (part of them were solved but some are not): - Video acceleration was not working out of the box on trusty desktop image but it was solved it by installing "Desktop-extras for Jessie-desktop (sunxi)" - it looks it could be added as default for trusty. But mvp package can't be installed due to depedencies to libs which I did not found in ubuntu reps?! - compositing if OFF in xfce but when I moving windows on the desktop, CPU load is becoming 100% till I stop movi…

Hi, when I try to update my core the apt-get install operation fails. This is because the post-installation script creates a symbolic link as the boot partition does not support because she is fat. Also the boot is only possible with a uImage not zImage I think. To compensate I am forced to make a copy instead of the link.

First off, I'd like to thank the maintainers for all the work you've put into Armbian. It's really been a pleasure to use. I'm currently using an OrangePI 2+as a kiosk computer, and I'm wondering if there might be some other way to wake it from sleep other than pressing the power button. Would it be possible for it to wake from sleep if one of the GPIO pins were pulled high, for instance? TIA, -Jim

Hi, I tryied a few times to run a RT kernel I built from https://github.com/igorpecovnik/lib as discribed in Armbian documentation and as in https://forum.armbian.com/index.php/topic/1950-orange-pi-pc-plus-armbian-guitarix-guitar-effectprocessor/page-2#entry16460. When executing compile.sh script it patch nice and good, then asks for Preemption Model and I chose 5 for Full Realtime. But when running the kernel into OrangePi it stucks in Starting Kernel. U-boot output: I am not choosing 1-4 for preemption model because I don't know if it will end up as an realtime kernel. The update from the older kernel to the rt one was done by dpkg -i on the deb files from the…

Dear Sirs and Madams! I am working on custom minimal image for NanoPi NEO and I've managed to solve majority of problems, however, if I observe boot process via /dev/ttyUSB0, I still get these two errors: HELLO! BOOT0 is starting! boot0 version : 4.0.0 boot0 commit : 1b3a1b587482affdd18aba923de7fe38eb7d5ee1 fel_flag = 0x00000000 rtc[0] value = 0x00000000 rtc[1] value = 0x00000000 rtc[2] value = 0x00000000 rtc[3] value = 0x00000000 rtc[4] value = 0x00000000 rtc[5] value = 0x00000000 rtc[6] value = 0x00000000 rtc[7] value = 0x00000000 DRAM DRIVE INFO: V1.3 the chip id is 0x00000081 the chip id is 0x00000081 the chip id is 0x00000081 the chip id is 0x00000081 the ch…

hi all i have an orange-pi zero that boots from network. the kernel and some other files are loaded over TFTP and the root path is mounted by NFS and every thing works fine. also i have a 3.5 inches LCD that works with fbtft_device module. the problem is when the board boots over network, the LCD dose not initialize completely but when i boot the board by SD card the LCD init's 100% fine. there are no error in dmesg but the LCD is 1/3 black and 2/3 white. dmesg: [ 51.270008] fbtft_device: SPI devices registered: [ 51.270303] fbtft_device: spidev spi0.0 33000kHz 8 bits mode=0x00 [ 51.270362] fbtft_device: spidev spi1.0 33000kHz 8 bits mo…

I have an issue with armbian installed oPI PC+. I have it in a case with a cooling fan installed and connected to 2 GPIO pins. My question is: could the cooling fan connection be the cause for my oPI PC+ won't shut down from the power supply and keeps running in the background after i shut down armbian? Any suggestions, I haven't tried starting without the cooling fan yet.

I have OPI 2 running latest armbian mainline with MQTT broker and home assistant only. And I've started to experience hard freezes that only power re-plug helps :/ At first I thought that only networking was gone, but I've triggered hearbeat on red onboard led and this led is just stopping blinking on freezes. I've even got rid of Network Manager and setup iface in old good way via /etc/networking/interfaces. Then I've connected to serial console, run minicom in screen with logging to file. Just to see if serial console would show some kernel panic or so...but nothing, no output on serial console. Anyone experienced such behaviour? How to debug it? My sec…

I'm trying to get TFTP support into U-Boot but it insists that 'no ethernet found'. I've added a couple of nodes to the device tree such that it has 'status = "okay" and mac-address = [00 00 00 00 00 00]; I've also added a top level alias in sun50i-h5-nanopi-k1-plus.dts (as added by @martinayotte following this thread) as below. Not sure if the U-Boot config needs changing in any way but the network components are certainly being built. Any thoughts most welcome. AATIA. aliases { serial0 = &uart0; ethernet0 = &emac; }; U-Boot dump of the loaded DTB on running system follows: => bdinfo arch_number = 0x…

Hello everyone. I have installed the Armbian Xenial Multimedia and desktop usage scenarios on my orange pi pc plus. Setup user and new password successfully. By using the command armbian-config I have solved my keyboard issue and language. Also network Lan0 is ok By typing sudo apt-get update and upgrade my orange is now updated succefully. But how to start the desktop ? I can only see the black screen with prompt command. If I reboot it , after all [ok] ...... I read Ubuntu 16.04.5 LTS orangepipcplus tty1 login ...... Did I do some mistakes?

Hi everyone, I am using nmtui to setup static ip both eth0 and wlan0 on orange pi zero. It works fine if only one of them was activated I want to use both. If LAN cable was be connected into pi, the board is run on ethernet. On other side, run on wifi when the cable was pluged out When I rebooted the pi without LAN cable, the eth0 auto activated lead to I can't access the module via wifi even though it is connected successful. I must connect via serial and disable eth0 after that I connected via wifi.

I have installed ~$ uname -a Linux orangepioneplus 5.4.18-sunxi64 #trunk.038 aplay -l **** List of PLAYBACK Hardware Devices **** card 0: allwinnerhdmi [allwinner-hdmi], device 0: 5091000.i2s-i2s-hifi i2s-hifi-0 [5091000.i2s-i2s-hifi i2s-hifi-0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: Device [USB PnP Sound Device], device 0: USB Audio [USB Audio] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1 works good alsamixer When choosing allwinner-hdmi

WiringNP does not work on NanopiDuo2, both in 18.04 and Ubuntu 20.04 Error piBoardRev: Unable to determine board revision from /proc/cpuinfo -> Is not NanoPi based board. -> You may want to check: -> http://www.lemaker.org/ open /sys/class/su Armbian /proc/cpuinfo content: processor : 0 model name : ARMv7 Processor rev 5 (v7l) BogoMIPS : 136.80 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm CPU implementer : 0x41 CPU architecture: 7 CPU variant : 0x0 CPU part : 0xc07 CPU revision : 5 processor : 1 model name : ARMv7 Processor rev 5 (v7l) Bo…

Hi all, I wanna try to use the hardware PWM on pin 7 of my orange pi one plus. Connect the fan. Toggle the SPI to enable, install wiring orangepi and all looks ok. But when in go to /sys/class/pwm i got a empty directory. I thought the should be a device pwmchip0 or something. I searched on the internet but can´t find a solution. This is what WiringOrangePi shows: Is there someone who knows what i do wrong or hwat i should do? Thank you!

Hi, I Would like to connect orangepi PC to 1280x1024 dvi monitor, as I used to with few years old armbian before. Tried h3disp but it reports that board/kernel is not supported. Is there some new method for that? Also it looks like armbianmonitor can't upload system info anymore.

I'm using a NanoPi Neo as Homegear gateway. This requires the SPI interface (/dev/spidev0.0). Yesterday I ran apt-get upgrade, which bumped my kernel from 5.10.60 to 5.15.25. No other changes have been done, Since then no SPI devices are created anymore and the gateway fails! I tried to downgrade the kernel already using armbian-config to 21.08 5.10.60-sunxi. But that reported an error (do not remember the text; was very late) and left the Nano unbootable. I could restore the 5.15.25 kernel by manually editing the zImage symbolic link in /boot. Using param_spidev_spi_bus=1 instead of 0 does not help. …

Hello guys, i'm trying to connect that ili9341 display with my m2 zero but it wont work. My armbian Version: Armbian_23-02-0-trunk_Bananapim2zero_lunar_edge_6.1.11_xfce_desktop The display has a pinout that matches with the raspberry pi, so also the banana pi m2 zero would do the job, since it has the same pinout like the raspberry pi has. It uses 26 pins to connect to the banana pi m2 zero gpio output pins. 3 buttons and a touch panel are available but i only want to use the lcd for now. I edited the armbianEnv.txt to open the spi port and added my overlay tft.dts to /boot/overlay-user but i cant get a picture on the screen, Its just glowing …

Hi Managed to get x11 to boot in latest armbian desktop Ubuntu gnome build x11vnc runs when manually running it fine but how many tutorials I have followed online it refuses to start as a service (auto) always gets bad access error when trying to get xauthority I guess ,even when I point it to the .xauthority files with -auth and used -auth guess tried all theses Tutorial 1 Tutorial 2 Tutorial 3 plus videos on YouTube has anyone got vnc to run on orange pi zero 3 Ubuntu noble gnome desktop From here at start up on x11? thanks

For some reason, the CPU frequency in Ubuntu is set to 1416000 while the hardware can reach 1512000, which is an improvement of about 6 and a half in CPU performance. I would appreciate a change or explanation. Thank you very much for everything.

hi im newbie OrangePI, how to make WiFiUSB work Bus 002 Device 002: ID 148f:7601 Ralink Technology, Corp. I try this step https://github.com/pvaret/rtl8192cu-fixesbut get error on this cmd sudo apt-get install git linux-headers-generic build-essential dkms root@orangepipc:~# git clone https://github.com/pvaret/rtl8192cu-fixes.git Cloning into 'rtl8192cu-fixes'... remote: Counting objects: 438, done. remote: Total 438 (delta 0), reused 0 (delta 0), pack-reused 438 Receiving objects: 100% (438/438), 1.80 MiB | 240.00 KiB/s, done. Resolving deltas: 100% (223/223), done. Checking connectivity... done. root@orangepipc:~# sudo dkms add ./rtl8192cu-fixes sudo: dkms: …

Hi all. I'm running armbian in all my orangepi boards since I've them and the distro is great and we'll developed. (thanks!) I run them with telephone chargers (htc and Samsung) 2/1.5A directly connected to the board via a 30cm cable. I don't know what's the status of data pins (d+ d-) but I think they are left open by the cable. They are used for sdr use running dump1090 all the time. In the aim of reducing the heat I've disabled two cores (only recently) out of four and installed a copper heatsink on the cpu. The problem is that from time to time I found my boards unresponsive from ethernet and serial port, so completely stuck. Only a reboot works. Do you h…

Hi all, First of all, a big thanks for making Armbian work, the work you guys have done is incredible. I have a BPI M2+ board and I have a problem getting the serial communication to work both ways. I am using the latest image that is available to download on the Armbian website version 5.20, Jessie server, 3.4.112 kernel. According to the board fex file (found here) the configuration for the uart2 is: [uart2] uart_used = 1 uart_port = 2 uart_type = 4 uart_tx = port:PA00<2><1><default><default> uart_rx = port:PA01<2><1><default><default> uart_rts = port:PA02<2><1>&l…

I managed to bust off the card slot on the pi lite. Can it be booted from USB or is this board done?

Hi all, I'm new here, and first of all I want to greet you. Last week I got a brand new Banana PI M2+, and tried to install the latest armbian Image on SD card. So far so good, but the M2+ is not booting from SD card. Except I short press the uBoot button followed by the reset button. This means I only get the board booted after a power cycle, if I press the uBoot button before. Then I tried to boot the board from NAND, but it is the same. It only boots from NAND, if I press the uBoot button before. (Installed to NAND before, of course) To verfy that I do not have any hardware issue, I downloaded a original Banana PI M2+ Image from the Banana-pi…

Hi Does anyone know how to make output via CVBS by using mode 10? ( 1080p60 ) I try to do it by changing the script.bin without success. dmesg output shows [DISP] disp_device_attached_and_enable,line:159:attched ok, mgr1<-->device1, type=2, mode=10 But TV shows no signal. Any ideas? Thanks.

Hello does someone have the working configuration enabling the onewire master bus on the mainline version ? I have tried to gather the information from several posts adding the missing configuration on the devicetree but as there is no real step by step guide and the kernel wiki entry makes no sense for the zero`s pins. Overlay or straight settings into the boot configuration.

Orange Pi Zero shows error [FAILED] Failed to start Load Kernel Modules. See 'systemctl status systemd-modules-load.service' for details. More details How to fix this error?

I'm getting the following errors when running "apt-get upgrade" by banana pi: $ sudo apt-get upgrade Reading package lists... Done Building dependency tree Reading state information... Done Calculating upgrade... The following package was automatically installed and is no longer required: python-dialog Use 'apt-get autoremove' to remove it. Done The following packages will be upgraded: certbot linux-image-next-sunxi python-acme python-certbot 4 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 1 not fully installed or removed. Need to get 15.9 MB/16.1 MB of archives. After this operation, 1,021 kB of additional disk space will be used. Do you wan…

Before I buy an AV cable for my orange pi zero I'd like to know how kodi performs on this board. I have this board and I'm thinking of running kodi if it's good enough to run it. If you've run kodi on the orange pi zero please let me know your thoughts about it.

I use a Beelink X2 Android TV box with Armbian Stretch mainline kernel 4.19.y Image on a SD Card. If I plug in my SD Card and then the power supply, the LED is purple and after some seconds blue. No picture over hdmi but the num-lock on the keyboard works. The box also don't get an IP over DHCP. No matter how long (1h+) I wait, nothing happens... When I plug in the power supply without the SD Card, the LED is red. The normal standby mode of the box. I can now plug in the SD Card and then power the system on. The LED switches to purple and after sone seconds to blue and Armbian is running fine, no problems. If the system reboots it will ru…

Hello I`m download newest version Armbian desktop for my Orange Pi. Install the following packages sudo apt-get install tightvncserver sudo apt-get install xrdp But I have error when I want connect to desktop from my Windows 7 Additional I try to connect use VNC Viewer but resulution is small and visual desktop is other the wwhen I`m normally attach HDMI monitor to OPI.

Hello I have an allwinner H2 & H3 (PC +) when it does not boot on my LAN. If I want to try to use the LAN port. In / etc / network / interfaces the eth0 interface is not defined. I tried to change the iso but on Windows the iso is not valid. On Linux Linux the files are not -w and try to change but not possible !!! If I want to try to use the UART port and PuTTY it doesn't go with in the prompt. U-Boot 2020.04-armbian (Sep 02 2020 - 10:21:09 +0200) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi PC Plus DRAM: 1 GiB MMC: Device 'mmc@1c11000': seq 1 is in use by 'mmc@1c10000' mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c1…

Hallo, I hope the topic hasn't existed before .. I have an Bananpi M2+ as H5 (64bit). Good Images are OrangePi-PC2 or NanoPi K1 Plus. My problem is, no support of emmc. Are there any known compatible images for the Banana Pi M2 + H5 that work? The NanoPi K1 Plus has problems rebooting and recognizing a keyboard. The OranngeP PC2 works fine, but no emmc support. Thanks and Best wishes, Mahdi2006

For those with a Radxa Cubie A7A/A7Z, I made a custom Armbian Build using the BSP kernel. https://github.com/NickAlilovic/build/tree/Radxa-A7A https://github.com/NickAlilovic/build/releases To build your own image: git clone https://github.com/NickAlilovic/build.git --branch Radxa-A7A ./compile.sh "do not change the kernel configuration" "show csc/wip/eos/tvb" "I understand and agree" "radxa-cubie-a7a" or "radxa-cubie-a7z" rest is up to you... Should you choose to run Armbian, ensure the CPU has adequate cooling by installing the Radxa Heatsink. https://radxa.com/products/accessories/heatsink-6…

hi all, I tried in various forums, but without an effective solution. I use cubieboard3 with cubietruck Linux cubietruck 3.4.104-sunxi #1 SMP PREEMPT Fri Oct 17 16:13:30 CEST 2014 armv7l GNU/Linux Debian GNU/Linux 7 \n \l When i run poweroff or shutdown -H or other option the system reboots instead of shutting down. ls -la /sbin/poweroff lrwxrwxrwx 1 root root 4 jul 18 2013 /sbin/poweroff -> halt if unplug li-battery shutdown work fine. Does anyone have any suggestions? regards

For some reason the reboot command doesn't appear to reboot the H3. Is this because it doesn't have a PMIC in the same way that the A20's do or is it just a case of the correct assembly instruction not being called?

Hello everybody, I can't run OpenGL ES on my OPI One's. I tried with a fresh new install distro : Armbian 5.13 (Armbian_5.13_Orangepione_Debian_jessie_3.4.112_desktop) with an HDMI-to-DVI screen ( h3disp -m 720p60 -d) This is what I've got : Any idea ? Does someone have the same issue ? Thanks all.

Hi, I have a new Orange Pi+ 2 and I was trying to write armbian image from: http://www.armbian.com/orange-pi-plus-2/(legacy build) but I couldn't make it work. Steps that I follow on Windows 10: - Download 7z file from armbian - Uncompress - Quick format SanDisk 32GB with SDFormatter - Write .raw file with Rufus 2.0.1 (stable). All preferences by default. - Insert micro SD to Orange Pi+ 2 - Connect HDMI, keyboard and power supply. - Green LED lights continuously. Why?? When the green LED was on, nothing happens. I had tried to install the official .img builds and just works. Why I couldn't with armbian bui…

I have been running Armbian_5.14_Orangepipc_Ubuntu_xenial_3.4.112 that has been upgraded to the 4.7.3 kernel via apt. Yesterday I allowed it to update to 4.8.3 and it won't boot anymore. Any ideas? I have reverted to the 4.7.3 kernel from a backup and it works again. I have isolated it to the packages :linux-dtb-dev-sun8i linux-firmware-image-dev-sun8i linux-headers-dev-sun8i linux-image-dev-sun8i Here is the startup output from serial port: ------------------------------------------------------------ OPTIONS: I18n Compiled on Feb 7 2016, 13:37:27. Port /dev/rfcomm2, 18:35:27 Press CTRL-A Z for help on special keys S=ca���A��`�b�``�g`C�9…

So I'm pretty new at using serial ports in linux so not even sure if this is the right place. I'm playing around with MIDI using the serial ports on the Orange PiLite - it uses the baud rate of 31250 to achieve this you use setserial to get the base_baud (which it reports as 1500000) and you divide by the speed you want to get the divisor i.e. 1500000/31250 = 48 this becomes >setserial /dev/ttyS1 divisor 48 speed_cust So now when you use 38400 as your baud speed it actually becomes 31250.... ...in theory after some fiddling I found the divsor is actually 50 as 48 gives you weird results which would suggest that the base_baud is actually 1562…

I was unable to get UART working on my Orange Pi Zero. Note, that I am not trying to use UART to access the terminal, I need to use the UART port to say connect to an arduino, etc. Here is the output of some commands that I thought may be helpful. uname -a Linux orangepizero 4.10.0-sun8i #14 SMP Fri Feb 24 03:02:58 CET 2017 armv7l armv7l armv7l GNU/Linux dmesg | grep TTY [ 0.000000] Kernel command line: root=UUID=b5fc390b-23ef-47a8-83fb-0fd94a3d2dcc rootwait rootfstype=ext4 console=tty1 console=ttyS0,115200 cgroup_enable=memory swapaccount=1 hdmi.audio=EDID:0 disp.screen0_output_mode=1920x1080p60 panic=10 consoleblank=0 enforcing=0 loglevel=1 ubootpart=8b70…