Allwinner sunxi

Hi, I have written a program with python e tkinter. The Gui automatically starts and runs well only I do access through remote desktop. How can I do that orangepi pc simulates the connection and starts my Gui? Sorry for my english, I hope I was clear enough. tx Ema

Hello Everybody !!! Armbian works great on beelink (Armbian_5.20_Beelinkx2_Debian_jessie_3.4.112) Just one last thing to reach the perfection : "speaker-test -twav -c2" gives good sound on hdmi But with mpv (and vlc previous version) hdmi sound and video are slowed... With audiocodec and sndspdif it's ok. Is it a known problem ? Is there other way to play sound and video ? cat /etc/modules #gpio_sunxi bcmdhd sndspdif sunxi_sndspdif sunxi_spdif sunxi_spdma sunxi-cir

I would like to upgarde my Cubietruck headless server from Legacy to Vanilla. With Legacy if I boot from NAND I can get my hard disc to spin down. But with SD card/sda root file system (as required by Vanilla) I can't get my disc to stop: if I issue 'hdparm -Y /dev/sda' it spins up again after a short interval. I have done everything I can think of to ensure that rsyslog is not writing to disc. Syslog shows frequent ata error messages that seem to coincide with the disc re-starting. Error msg: kernel: [ 104.477850] ata1.00: exception Emask 0x0 SAct 0x200 SErr 0x0 action 0x6 I have tried this on two different Cubieboards with different makes of hard…

Hi guys, ive installed armbian 5.2 into my opione, now what should i do? Videos 1080p work slowly in kodi, i have to do something? Thanks Inviato dal mio HUAWEI SCL-L21 utilizzando Tapatalk

Hi there, I pulled the latest changes from github and created a fresh Debian Jessie Armbian Image for my BananaPi M2+. Specifically, I run: BOARD=bananapim2plus BOARD_NAME="Banana Pi M2+" VERSION=5.21 LINUXFAMILY=sun8i BRANCH=default ARCH=arm Through a lot of debugging and googeling, I found that the latest armbian Image uses a different BCM driver (https://github.com/igorpecovnik/lib/issues/484). Now I face the following issue: In order to use AP6216 with hostapd in access point mode, I added "bcmdhd op_mode=2" to /etc/module. I tried a number of things, e.g. using dhd instead of bcmdhd but without success? Any ideas where I can configure AP6216 in op_mode=2 (access …

Hello everyone I do not know how long, but I found out today that they no longer the wlan0 interface slla my lambo r1. I do not remember to have done in the configuration file changes lately. What can I check? These are the message by the boot if they can help: [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.7.3-sunxi (root@xenial) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.1) ) #26 SMP Wed Sep 14 19:50:18 CEST 2016 [ 0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data ca…

I managed to bust off the card slot on the pi lite. Can it be booted from USB or is this board done?

Hi, I'm trying to install my laser printer Brother HL 2130 in Armbian Jessie. The thing is, that in my older Armbian Wheezy system with same board and printer it works. Anyone has a clue? Maruprez

Hi all, I'm writing this post because I had an issue upgrading my lamobo-r1 from the previous version to the current one (Armbian_5.20_Lamobo-r1_Ubuntu_xenial_4.7.3). On reboot hwclock doesn't start so I get my clock set to epoch, wan doesn't go UP, postfix says "time stamp 2015-11-25 01:40:22 is 1448411826.350146139 s in the future", random says "uninitialized urandom read"... a total mess. As pointed out on some sites, looks like "/etc/init/hwclock.conf" has "start on starting mountall" so failing to mount could cause a failing in hwclock initialization. I also found on bugs.launchpad.net/ubuntu that in recent versions with systemd, mountall became fussy about fi…

Hello. I am new to Armbian. My Banana PI M2 (already a disappointment, bad purchase on my part) is up and running but will not reboot all the way. It shuts down but does not restart again. Any ideas how to go about troubleshooting and fixing this? It is a deal breaker for what I planned to be a headless system. It needs to be restartable without physically pulling the plug to do so.

I have done a fresh install of Armbian 5.20 for my pc+. I was hoping that the software defined radio software GQRX would now be able to find Pulse Audio and work properly. But I still get the same error. 192.168.6.103george@orangepipcplus:~$ sudo gqrx [sudo] password for george: linux; GNU C++ version 4.9.1; Boost_105500; UHD_003.007.003-0-unknown gr-osmosdr 0.1.3 (0.1.3) gnuradio 3.7.5 built-in source types: file osmosdr fcd rtl rtl_tcp uhd miri hackrf bladerf rfspace airspy Using Volk machine: neon_hardfp_orc pulseaudio/pa_sink.cc: pa_simple_new() failed: Connection refused Could not resolve property : pattern10600 Could not resolve prope…

Hi Guys, a few weeks ago, I implemented a project wich reads the power sources of my Banana Pi. I was using /sys/power/axp_pmu/. I now made a new build to enable lcd display and such things. But now /sys/power/axp_pmu/ isn't there. Also can't find it anywhere in my system. Only /sys/power/{pm_async, pm_freeze_timeout, state, wakeup_count} Kernel of new build is 4.8.0 What have I to do, to get axp_pmu back? Martin

Hello to all! I have banana pi m2+ with Allwinner H3. OS: ARMBIAN Debian GNU/Linux 8 (jessie) 3.4.112-sun8i I program linux kernel driver. And I am can't run R_UART. I write to register any value, and read value alway zero. It seems that APB0 bus is not cloked. Or device R_UART reset asserted. What I do wrong? Sincerely, Dmitriy.

I'm getting broken connections when I download big files from my Cubietruck. I've tried reducing CPU freq and setting eth0 to 100 half duplex, as recommended in various places. No joy though. It is said that a GMAC fix for this went into u-boot in mid 2015 but my u-boot appears to be older: $ strings /boot/linux/u-boot.bin | grep 201 U-Boot 2011.09-rc1-00000-gc1cb2f9 (May 30 2014 - 10:19:03) Allwinner Technology arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2010.09-50) 4.5.1 GNU ld (Sourcery G++ Lite 2010.09-50) 2.20.51.20100809 $ cat /etc/armbian-release # PLEASE DO NOT EDIT THIS FILE BOARD=cubietruck BOARD_NAME="Cubietruck" VERSION=5.20 LINUXFAMILY=sun7i BRA…

Hi. I'd want to set a custom MAC address to my cb2. I set the static mac address in u-boot environment variable ethaddr. If i print the environment (with "printenv command" i find it right there but when the system starts and i go through ifconfig i can see eth0 has a different MAC. Any suggestion on how to get MAC from u-boot? I'm on Armbian 5.20 legacy kernel. Thank you

Good afternoon dear experts. I have a problem on my Orange pi plus 2. My hard drive(WD Red WD10JFCX, 1Тб, HDD, SATA III, 2.5") is periodically switched-off (/dev/sda1). in ravines I have: Sep 28 10:48:37 PM dvr kernel: [1678371.474389] ehci_irq: highspeed device disconnect Sep 28 10:48:37 PM dvr kernel: [1678371.474593] usb 3-1: USB disconnect, device number 2 Sep 28 10:48:37 PM dvr kernel: [1678371.479539] Buffer I/O error on device sda1, logical block 76682192 Sep 28 10:48:37 PM dvr kernel: [1678371.479581] Buffer I/O error on device sda1, logical block 76682193 Sep 28 10:48:37 PM dvr kernel: [1678371.479609] Buffer I/O error on device sda1, logical block 76682194 …

Hi, I am using Armbian_5.20_Orangepiplus_Debian_jessie_3.4.112.img with emmc nand flash. I want to make .img file for emmc nand flash. because i am plan to use Phoenixsuit tool.. how can i make emmc nand flash image file? please help me.. thanks.

Booting my A20-OLinuXino-MICRO with the Armbian_5.20_Micro_Debian_jessie_4.7.3.7z (freshly downloaded) image from SD card hangs with these last log lines: [ 17.564273] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 384000 KHz [ 17.599267] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 528000 KHz At the start of the boot, there are also some bad looking error messages from U-Boot: Failed to set core voltage! Can't set CPU frequency Trying to boot from MMC1 U-Boot 2016.09-armbian (Sep 15 2016 - 05:13:34 +0200) Allwinner Technology CPU: Allwinner A20 (SUN7I) Model: Olimex A20-Olinuxino Micro I2C: ready DRAM: 1 GiB M…

Hi, I have a orange pi one which I use as a test web server and everything was good so far, the first problem I came a cross that the couchbase server on debian package did'nt support arm, so I skipped that and used another computer as couchbase server, But the problem now is that I can't install the couchbase php client on the orange pi, then I tried the build the libcouchbase my self. I actually did build it (I have no previous experince with build) After I built it I don't know what to do, now I have libcouchbase.so file and other files but I can't still use couchbase php commands. Any help is appriciated. Thanks.

Hello, I made a fresh install of Ubuntu 16.04 lts (ARMBIAN) on armhf cubietruck (Armbian_5.20_Cubietruck_Ubuntu_xenial_3.4.112) . libav-tools is installed along with MPD & MPC. service mpd status reports: "mpd[6770]: /usr/bin/mpd: error while loading shared libraries: libavformat-ffmpeg.so.56: cannot open shared object file: No such file or directory" What is missing to start MPD? Best regards, Martin

Hi first of all sorry for my bad English .I have an OPI PC + ,I install Ubuntu on my sd card and after boot i used nand-sata-install command to use may nand but when i tryied to use my sd card (after format sd card) it did't work and after reboot i receive "panic= boot argument" how can i use my sd card and mount it when my dist installed on nand? even i checked this link for Cubietruck but it wasn't useful for OPI , and then i checked this and it was really hopeful but I don't now how can i exactly implement this .Actually I need to auto mount my sd card as a result when I reboot my OPI PC + I need my OPI boot from emmc instead of sd card. thank you for you…

Hi, I have a beelink X2 and did: apt-get update apt-get upgrade apt-get install -f apt-get update apt-get autoremove -y I think i have version 5.20. If i look at: cat /etc/*-release # PLEASE DO NOT EDIT THIS FILE BOARD=beelinkx2 BOARD_NAME="Beelink X2" VERSION=5.20 LINUXFAMILY=sun8i BRANCH=default ARCH=arm PRETTY_NAME="Debian GNU/Linux 8 (jessie)" NAME="Debian GNU/Linux" VERSION_ID="8" VERSION="8 (jessie)" ID=debian HOME_URL="http://www.debian.org/" SUPPORT_URL="http://www.debian.org/support" BUG_REPORT_URL="https://bugs.debian.org/" So i think i have version 20 But if i do an: cat /proc/version Linux version 3.4.112-sun8i (root@xenial) (gcc…

Hi, is one of your images able to play movies and watch youtube?

Hi, Seen some posts where mentioning that depending of the version of kernel there is either FEX or DTS usage, old ones called Legacy, using FEX to define GPIOs and Peripherals pins. Wit Mainline Kernel, is using DTS. Yet in the recent kernel (dev) armbian builds, eg armbian 5.21, kernel 4.7.6 (on H3, NEO), seen the /boot containing all the FEX stuff script.bin etc. Is FEX still used in the mainline kernel builds? C:\Christos>ssh christos@192.168.1.131 christos@192.168.1.131's password: setsockopt IP_TOS 16: Invalid argument: _ _ ____ _ _ _ | \ | | __ _ _ __ ___ | _ \(_) | \ | | ___ ___ | \| |/ _` | '_ \ / _ \| |_) | | | \| |…

Hello everyone, I am kinda of new to the orange, I think it's fantastic, I worked with rasp for while and I think the orange just slashes it. Pampering the orange aside, I am trying to hook up an old webcam to the Orange pi lite and I running into some issue, my lsusb info is this: Bus 003 Device 002: ID 1e4e:0100 Cubeternet WebCam When I start motion, everything works fine, although when I go on the browser a gray screen comes up saying: unable to open video device I have changed the configuration file of /etc/motion/motion.conf and /etc/default/motion as instructed here: http://www.orangepi.org/Docs/Webcams.html Plus I have changed the with my i…

Hi, I own several SPI touch displays, and I would like to use them with armbian. I got the displays to work already, but I'm now trying to get the touchpanels to work also. I'm using Debian Jessie Server Legacy 5.20 with a BananaPro board. I tried to add the module to /etc/modules : ads7846_device gpio_pendown=17 cs=1 x_plate_ohms=400 pressure_max=255 swap_xy=0 ads7846 ... does not work, I don't even see an error in dmesg. I also tried to put the options in a /etc/modprobe.d/ads7846.conf, /etc/modprobe.d/ads7846_device.conf and /etc/modprobe.d/fbtft_device.conf but nothing works. Manual modprobe : modprobe ads7846 loads fine (I could see it in lsmo…

Hi All, I'll start with I know this is a dev image...... but I would like to see the 4.x kernels working on the Orange Pi Lite, so would like to be able to find out why it's not and help get that resolved in any way I can. I have 2 images, both were built using the compile.sh: Armbian_5.20_Orangepilite_Ubuntu_xenial_3.4.112.img Armbian_5.21_Orangepilite_Ubuntu_xenial_4.7.6.img I dd'd the 3.4.112 kernel image onto a Micro SD, put it in to my Orange Pi Lite and booted it up and confirmed it was working as expected, the green light flashed, the red one also flashed on first boot, then after the reboot I logged in, changed password etc. I then powered off th…

Hey there, I am a long time user of your armbian operating system. It is great, I am using it for a simple home NAS system. But I have found one problem with armbian, which is very annoying: My standard Banana Pi keeps loosing the HDD Ive connected over Sata. It is a 3,5" Seagate Barracude 3TB drive formated as Ext4. It gets 5V and 12V power and runs quite perfect, as long as it has something to do. It spins up and down as I configured it. But when I leave the pi for a longer time period unattended (no workload), and the harddrive stays in spindown-mode too long, it wont identify the HDD anymore. The mount point and the /dev/sda are gone. I need to powercycle t…

I have tried to do everything, when I turn on gpu on chormium-browser animation html5 is very slow. Anybody fix or find something ? what chromium version you use ... what mali driver you setup ? very hard to have a good result orange pi PC with armbian 5.20 jessie ! thx you

Hi, I'm Olivier, french engineer, and i have bought an orangepi plus card in april. I use linux (x86) since 1994 Sorry for my bad english ... I was happy to find Armbian because linux images provided by xunlong have many security problems (example / and all system directory aren't owned by root but by orangepi user). Thank for your work on Armbian. My Orangepi + has been installed with a 5.10 armbian image (Armbian_5.10_Orangepiplus_Debian_jessie_3.4.112) and run perfectly. I wanted upgrade to 5.20 and since the card doesn't boot anymore. I can boot with the native android on NAND memory but I can't boot on SDcard. When I boot on sdcard, only gr…

I got my Nanopi M1 today and then installed RetrOrangePi on it. Every was fine until I started Openelec and can't go back to the EmulationStation. Can anyone guide me to go back to that menu? Thank you very much

I got 2 x Orange PI pc+ running Armbian (install by same SD card on eMMC). My two orange pi pc+ got same wlan0 mac address. I did research on forum and saw some suggestion about bug of Network-Manager. I try remove (purge) Network-Manager but see no difference. I also try look in u-boot but don't know how to set mac address on the u-boot part. How should I make my 2 pc+ board have difference mac address? want to run these two board under the same wifi network. Please suggest. Thank you very much in advance.

Hi! My Banana pi Pro with Armbian v5.20 does not boot since i issued a 'init 1' command. While booting, it show only that; Starting kernel ... Uncompressing Linux... done, booting the kernel. How to activate the boot debug mode. I tried many keyboard keys without success. Thank you!

Hello, I have OPI_PC(or OPI_+2): marian@orangepipc:~$ cat /etc/*-release # PLEASE DO NOT EDIT THIS FILE BOARD=orangepipc BOARD_NAME="Orange Pi PC" VERSION=5.20 LINUXFAMILY=sun8i BRANCH=default ARCH=arm PRETTY_NAME="Debian GNU/Linux 8 (jessie)" NAME="Debian GNU/Linux" VERSION_ID="8" VERSION="8 (jessie)" ID=debian HOME_URL="http://www.debian.org/" SUPPORT_URL="http://www.debian.org/support" BUG_REPORT_URL="https://bugs.debian.org/" and Skystar usb_2_hd_ci(or TT connect 3650). marian@orangepipc:~$ Module Size Used by mali_drm 2732 1 drm 178255 2 mali_drm mali 123208 0 ump 29…

I can't get this dongle to work with 5.20. $ lsusb Bus 002 Device 002: ID 148f:5370 Ralink Technology, Corp. RT5370 Wireless Adapter Seems to be known one. $ lsmod Module Size Used by rt2800usb 13858 0 rt2800lib 42835 1 rt2800usb rt2x00usb 8227 1 rt2800usb rt2x00lib 34544 3 rt2x00usb,rt2800lib,rt2800usb mac80211 363732 3 rt2x00lib,rt2x00usb,rt2800lib mali 185786 5 ump 30408 1 mali mali_drm 2728 0 drm 178585 1 mali_drm Nothing wrong here? I guess so, wpa_supplicant is properly configured (ssid & psk),…

Hi. My platform is Orange Pi Plus. I connected SATA HDD and installed Armbian. Using nand-sata-install I created the following scenario: boot from SD, system on SATA. I also installed lighttpd. Several days everything works fine and than: ...file system on the root filesystem failed … rebooting automatically due to panic= boot argument... After that the PC just reboots constantly and I can do anything. The only solution I found is to repeat the process of boot SD creation. But after that I need to install everything again. All this I already did for several times... What maybe the reason of this error? Can I exclude the SD card and use eMMC instead? Is there anythi…

Is it possible to upgrade my running armbian server version to the desktop one? Thanks...

Hi dear. I have some question about orangepi plus. I am using orangepi+ and The latest Armbian Debian Version was installed in emmc. and i have some BLE Module. but, when i add my module to gpio pin, i can see I/O Error..but it's not always, somtimes there is no error. and when i boot orangepi-plus, it is PULL-UP state. i don't know this reason, how can change default gpio pull-up or pull-down state? or you have some idea? thanks

Hi, I have a orange pi one and the jessie-lite from this site. Everything runs fine when freshly installed, however after apt-get upgrade and init 6 it stops working. I get nothing displayed on my hdmi any longer etc. Any ideas?

Thanks to the latest Armbian and my own script - I now have a NanoPi Neo (two of them actually) running everything I want - Node-Red, Mosquitto, SQLITE3 etc..... got control of serial ports - marvelous. I have only one problem - I have no idea despite several experiments - how to get WIFI working on the standard cheap Wifi dongles you get on Ebay. (usually say 802.11n on the black plastic end). Anyone succeeded with this? Pete.

Hi, after upgrading (and NOT following 'How to update) and reboot my cubietruck doesn't boot anymore. It's looking for a pxe-boot. Would anybody please be so kind and give me some help? Thanks, AxHa

Hello Im trying to mount an USB HDD on my Orange Pi One with Armbian 5.20 like this and never mounts. In previous versions i was able. What i do is add this lin to Fstab /dev/sda1 /mnt/usb ntfs auto,users,noexec,rw, uid=1000,gid=1000 0 0 Anybody tried to mount any usb with Sucess? Thanks 4 ur help

I was testing the orangepi PC+ armbian build 5.20 (Armbian_5.20_Orangepipcplus_Debian_jessie_3.4.112_desktop) when messing with it it seemed to have random reboots. I thought initially it was because it was lacking a heatsink or fan. So I added both and the issue persisted. Thinking maybe if I flashed to emmc it might resolve the issue it froze in emmc install and is effectively softbricked from what I can tell sadly. I also tested a second OPIPC+ but was unable to get it to boot. I tested with multiple new power cables as well.

Hi everyone, I have recently buy a Orange Pi plus 2e. I installed Armbian legacy/server on it. When I plug a 3.5 HDD (in self-powered USB box), I have this message in log (dmesg) : [ 13.654305] ehci_irq: highspeed device connect [ 13.920099] usb 3-1: new high-speed USB device number 2 using sunxi-ehci [ 14.074826] scsi0 : usb-storage 3-1:1.0 [ 15.070939] scsi 0:0:0:0: Direct-Access WDC WD30 EFRX-68EUZN0 PQ: 0 ANSI: 5 [ 15.073286] sd 0:0:0:0: [sda] Very big device. Trying to use READ CAPACITY(16). [ 15.073771] sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) [ 15.074679] sd 0:0:0:0: [sda] Write Protect is off [ 15…

Hey. I'm not sure if I perhaps caught the Armbian website in the middle of an update, but there doesn't seem to be any Ubuntu (Xenial) builds for H3 boards anymore ... with the exception of the NanoPi Neo. It's all Legacy Jessie builds right now. Thanks,

Hi all, I'm new about u-boot and arm device. I was learning how to build u-boot for banana pi m2+. Where I can get working u-boot defconfig for that device? Thanks

Hello, I am trying to switch from an older wheezy (lemaker) install to a newer Armbian Jessie install, (5.14 Armbian).By using the Legacy Kernel I can load ft5x drivers for the 5" PCAP Screen. So Far, everything is working normally except much faster and reliable. My Problem is that I can't read the analog voltage from my MCP3002 anymore using spidev python module. I have spidev and spi-sun7i in /etc/modules ls /dev/spi* /dev/spidev0.0 /dev/spidev0.1 dmesg | grep spi [ 1.202344] [spi-inf] Found 2 spi devices in config files [ 1.209170] [spi-inf] boards num modalias max_spd_hz bus_num cs mode [ 1.212928] [spi-inf] spi_board0 …

Hi guys, I'm running Armbian on my BananaPi for almost a year now and it has always run seamlessly, since the latest upgrade to Arabian 5.20 (Kernel 4.7.3) I've started to experience problems with the stability of the daemons. Monit is doing an hard job lately restarting many times a day almost all the processes I'm running as damons, the most affected by the Killing are Python 2.7 (running Sickrage) and Deluge daemon. In particular Deluge being killed so many times a day is quite annoying since I have to recheck the integrity of many files almost every time I get the service up again. I didn't install any additional software that could have created this inst…

I Installed the Armbian system who is dedicated for my OPI version: http://www.armbian.com/orange-pi-pc/ with instruction, formatted SD card with format size adjustment option ON. But when I want to boot it there is only still green light (steady all time). OPI not giving any boot information on screen. This issue is not caused by SD card becasue I tried two (which one is recommended): Kingston 32GB (class 10) and Samsung EVO+ 32GB. Has anyone had similar experience or have any idea how to solve this?

I'm not sure if this is off-topic, but I'd like to ask the forum about a problem. My goal is to run RPi-Cam-Web-Interface (http://elinux.org/RPi-Cam-Web-Interface). I have 5.20 Jessie server 3.4.112 that has been updated/upgraded on an Orange Pi One with a gc2035 cam on an expansion board from aliexpress. As a first step I got the cam working. There are some threads in this forum that made that easy. I then installed github.com/roberttidey/userland since it includes raspimjpeg - a key element in the RPi-Cam-Web-Interface toolchain. But when I run raspimjeg I get the error * failed to open vchiq instance Google has solutions that involve permissions…

I'm trying to recompile the image from source (because I want the kernel with SATA PMP support, and I got the SATA port multiplier and 3 drives ready), but failed in the last step. As the attached image, the problem should be caused by "Device or resource busy". I'm using a fresh downloaded Ubuntu 16.4 VB image and follow every instructions in github. So, how can I get rid of it? Am I missing something? Thanks.

Hello, I am trying to get my Orange Pi One working with my ili9488 LCD screen. I followed a few "how-to's" , This one in particular There is a comment there that mentions how to do it on the Orange Pi. Also this post here. I must be missing something, because when I did all the actions listed in every "How To" I found; all I get is a black screen with a white bar down the side. Does anyone know of a comprehensive how-to on getting this screen to work?

Hello every one, I have used crosstool-ng on my Jessie server (x86), and downloaded the linaro toolchain for my Ubuntu (x64 / 16.04) laptop, but ran into a wall both times: the cross-compilers won't (and now that I think about it, can't) link to the host libraries. Do I simply get all the sources for the libraries I want/need, and adjust their configure parameters to point to dedicated directory, and then build my target? Is there an easy way to manage the versions / dependencies to match Jessie (the version on my target OPi)? I am trying to compile Duktape with libreadline, if that matters. Thanks, Steve

Orange Pi PC slow browser performance and very slow video playback in browser from youtube does anyone else have same issue ? any way to fix this ?

Hello, I'm trying to boot an Orange Pi Plus with Armbian 5.20, and it does not work. I've already check that both OPi and my sdcard work fine, because I can flash and boot the images on orangepi.org site. Besides, I checked how u-boot starts with both Armbian and "debian server" orangepi.org image (both attached)

Hello I am a new user of the armbian software. I installed the latest version of vanilla to armbian in the description of the material, I saw that the buscan was activated. I have a banana pi pro, I would like to know how to install the software for CAN bus. I read that can4linux was the driver to install. I read on this forum they've installed patches, but how do I installed a patch? Thank you for your help. PS: I speak French and I use a translator.

I need/want USB ethernet via OTG. I've wasted over 16 hours trying to get the g_ether module to work. A prominent poster told me that all recent Armbian images have this ability, just follow the directions... It's not. I'm using the stock Armbian image from this website, and I've updated it via "sudo apt update && sudo apt upgrade". Still no luck. The OTG connection currently shows up as a USB serial gadget, but I want a USB Ethernet gadget.

Hi all, First of all, a big thanks for making Armbian work, the work you guys have done is incredible. I have a BPI M2+ board and I have a problem getting the serial communication to work both ways. I am using the latest image that is available to download on the Armbian website version 5.20, Jessie server, 3.4.112 kernel. According to the board fex file (found here) the configuration for the uart2 is: [uart2] uart_used = 1 uart_port = 2 uart_type = 4 uart_tx = port:PA00<2><1><default><default> uart_rx = port:PA01<2><1><default><default> uart_rts = port:PA02<2><1>&l…

There is problem with the internal wifi on Orange Pi Lite and Armbian 5.20 (5.16 too). I installed tshark (and tcpdump) and try to capture wifi packets in monitor mode. Without success. What's better. Aircrack-ng works flawlessly. I think, pcap library has a problem with switching the device to monitor mode. "dumpcap: The capture session could not be initiated on interface 'wlan0' (wlan0: SIOCGIWPRIV: Argument list too long)." 'iwpriv' command runs without error, but the private command list is really long. Buffer too small?? Dumpcap run with no errors on external USB wifi dongle (TP-Link TL-WN722N), so I think problem is in firmware of internal wlan chip…

Hi, I've had a PcDuino3 for some time now, but I have barely used it because linksprite work was shoddy; so I never bothered to give the pcduino much time. I Also own a banana pi (A20), an O-DROID XU-4, several rPi's and an Orange Pi PC. All non rPi's are running armbian; you are all awesome for your work! I think I understand this problem with 4.x has something to do with the device tree .dtb files, but no clue what to do to get it to boot and display through HDMI. I'm actually wanting to use it as a headless server, but initial setup requires me to see the screen only because the onboard wifi is not working either (despite manually editing /etc/wpa_supplicant/wp…

Hi, I updated my system to version 5.20. This version is supposed to solve the problem of bluetooth.But this is not the case. Can you help me? thanks. ps : dmesg | grep ap6210 : 8.054958] [ap6210] select wifi ap6210 [ 8.058372] [ap6210] Initializing ap6210. [ 8.063627] [ap6210] platform device registered successfully. [ 8.067651] [ap6210] Using ap6210 configuration. [ 8.288340] [ap6210] WLAN placed in POWER ON [ 8.559560] [ap6210] Linux Kernel SDIO/MMC Driver [ 8.582485] [ap6210] Broadcom Dongle Host Driver: register interface [wlan0] MAC: 00:90:4c:11:22:33 [ 8.947049] [ap6210] WLAN placed in RESET [ 10.468573] ap6211: exports du…

Hey, for the LEDs the option "disk-activity" which was possible in Wheezy Legacy is no longer available. Is it possible to re-add that? Thank you, Ingo Fischer

I have a BananaPi M1+ running pure-ftpd, it was fine when using Armbian 5.14, but I have a problem after upgraded to Armbian 5.20. Here is the output of the filezilla client : If I disable the firewall by clearing all the iptables rules, filezilla can connect to pure-ftpd without problem.

Hi guys, I use last armbian on banana pi m2 plus, how to set mac address randomly? In raspbian, it only remove /etc/udev/rules.d/70-persistent-net.rules, and reboot, then the raspberry pi will get difference mac address. But in armbian, it seems not working. thanks for anyone help.

Please help me. I have (had?) armbian Ubuntu 16.04 legacy installed on NAND. Today I upgraded 13 packages and now the system does not boot anymore. Black screen and only the red led id on. What I didi wrong? And is there a way to recover the system (e.g. using an old copy in the SD)? This is the output: The following packages will be upgraded: armbian-firmware armbian-tools-xenial libnss-myhostname libpam-systemd libsystemd0 libudev1 linux-headers-sun7i linux-image-sun7i linux-u-boot-cubietruck-default linux-xenial-root-cubietruck systemd systemd-sysv udev 13 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 140 MB of archives. After …

Hey, I have one Cubietruck newly installed with Xenial some weeks ago and one Cubie that had Trusty installed. Both Armbian. So today I made the dist-upgrade from Trusty to Xenial. After doing everything and reactivating the sources.list entries for Armbian and NodeJS (shoud be added to the FAQ!) i compared the output of apt-get update and ther eis a difference: Originally installed with Xenial (also InfluxDB installed, so should be only difference): Hit:1 http://ports.ubuntu.comxenial InRelease Hit:2 http://ports.ubuntu.comxenial-security InRelease Hit:3 http://apt.armbian.comxenial InRelease Get:4 http://ports.ubuntu.comxenial-updates InRelease [95…

First of all I've got an OPI PC and I'm newbie with armbian and Linux in general I've managed to read DS18B20 temperature sensor and now I want to read Temp and Humidity from a SHT75 sensor which has the same specifications as the SHT1X family of Sensirion sensors. I've installed WiringPi library and I've been searching on google how to make SHT75 work with little success Any documentation or examples to see?? Any help would be appreciated Thanks

Hi All, Sorry if this has been asked before, I haven't been able to find the answer yet. I wish to configure my OrangePi's (Lite and PC+) such that they power on automatically whenever the power is restored after a power outage without needing to press the power button. I'm not sure where we could configure this as the OrangePi's don't seem to have a bios like a Desktop PC. Dave.

Hi guys, I installed last armbian on Banana Pi M2+, and execute nand-sata-install.sh to boot armbian from emmc, it works fine. I want system boot from emmc, and storage some data to sd card, so I prepare one sd card with ntfs partition, insert to Banana Pi M2+, and boot. It cannot boot, and message are: U-Boot SPL 2016.05-armbian (Jun 23 2016 - 09:59:04) DRAM: 1024 MiB Trying to boot from MMC1 U-Boot 2016.05-armbian (Jun 23 2016 - 09:59:04 +0200) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi PC DRAM: 1 GiB MMC: SUNXI SD/MMC: 0 (SD), SUNXI SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial…

Finally Orange PI Family gets the 4.x kernel support.But there is no Vanilla Kernel on Orange PI PC.Please add the support on Orange PI PC.Thx!

First of all, thank you very much for the great work! On cubietruck after upgrade to 5.20, I have some trouble with network bonding. /etc/network/interfaces: auto eth0 iface eth0 inet manual bond-master bond0 bond-primary eth0 bond-mode active-backup auto wlan0 iface wlan0 inet manual wpa-ssid xxxx.xxx wpa-psk xxxxxxxxx bond-master bond0 bond-primary eth0 bond-mode active-backup # Define master auto bond0 iface bond0 inet static address xxx.xxx.xxx.xxx netmask xxx.xxx.xxx.xxx gateway xxx.xxx.xxx.xxx hwaddress ether xx:xx:xx:xx:xx bond-slaves none bond-primary eth0 bond-mode active-backup bond-…

I've upgraded to 5.20 from 5.17 and I've had to modify my /boot/bin/micro.bin to activate the VGA output. After Upgraded the board didn't reactivate the VGA, and I've to do it manually. Maybe some warning in the changelog will be an help to those have to do such modifications. The upgrade process copied the bin dir to bin.old. I have to apply "sudo apt-get upgrade" twice as the first run complain about come conflicting files and abort the upgrade, the second run did the job. I'm running legacy debian Jessie image and upgraded from 5.17 to 5.20. Now it seem to work well.

Hi everyone, I am having issues with video output on my A20-micro when using legacy kernel. I get the proper output from uboot, but when it starts to load the kernel, I get some garbage on the screen, then nothing. I had a look through the forums to no avail. My boot logs are uploaded to http://sprunge.us/dGhS From what I see, the default kernel command line seems to be correct for my purpose. The system is up and running as I can login through serial and SSH. I tried setting the resolution with a10disp but I got the following response: "Cannot change HDMI mode because HDMI is not enabled." Anyone has a clue on what I am missing ? Than…

Hello, I Just installed armbian in my cubieboard and dmesg is showing an annoying message: [ 70.366543] rc rc0: IR event FIFO is full! [ 70.382773] rc rc0: IR event FIFO is full! [ 70.398930] rc rc0: IR event FIFO is full! [ 70.414907] rc rc0: IR event FIFO is full! [ 70.430890] rc rc0: IR event FIFO is full! [ 70.446706] rc rc0: IR event FIFO is full! [ 70.462248] rc rc0: IR event FIFO is full! [ 70.477582] rc rc0: IR event FIFO is full! [ 70.492758] rc rc0: IR event FIFO is full! [ 70.507816] rc rc0: IR event FIFO is full! [ 70.522829] rc rc0: IR event FIFO is full! [ 70.537806] rc rc0: IR event FIFO is full! [ 70.552683] rc rc0: IR event…

Hi, I just want to inform that probably there is a problem with correct detection of platform. Originally I had everything set for Orange Pi Plus 2E. However, after upgrade avery file is related to Orange Plus (2) - not 2E: Previously in any mentioned file there was orangepiplus2e identifier. Please see also dpkg.log: 2016-09-19 11:00:20 startup archives unpack 2016-09-19 11:00:21 upgrade linux-firmware-image-sun8i:armhf 5.16 5.20 2016-09-19 11:00:21 status half-configured linux-firmware-image-sun8i:armhf 5.16 2016-09-19 11:00:21 status unpacked linux-firmware-image-sun8i:armhf 5.16 2016-09-19 11:00:21 status half-installed linux-firmware-image-sun8i:armhf …

Tried on both 5.17 and 5.20, Debian and Ubuntu with legacy kernel. Debian has systemd 215, Ubuntu has 225 iirc. If I plug an iphone usbmuxd is started by systemd-udevd as directed by udev rule (stock one) and gets shut down when I unplug it, again how it's supposed to be. The problem is, it does not start if I plug any Apple device again. Restarting systemd-udevd service does not help at all, and when I reboot the board usbmuxd gets started when I plug iphone but again only once. 1st plug in/plug off in syslog: Sep 19 09:26:57 localhost kernel: [ 90.005422] ehci_irq: port change detect Sep 19 09:26:57 localhost kernel: [ 90.279798] usb 2-1: new high-speed US…

At first i like to say that this problem is not caused by Armbian. On my OpiPC+ my EMMC has became unusuable. I got a first hint to this by updating 5.17 Jessie Desktop to 5.20, that failed after downloading 135 MB of Files. I did not thought of an Error and compiled 5.20 myself, put it on SDcard and run nand-sata-install. The Script does it work without any Errors, but after power down, the Opi did not come up again. Put in the SDcard again and tried to look at the EMMC but it was not mountable. There were some Errors fixed by running fsck but next time i tried to write on the Emmc i got Errors again, in fact i tried to run nand-sata-install again after i trie…

I install Jessie server armbian on orange pi and install wiring op on it from this link https://github.com/zhaolei/WiringOP and for test interrupt I use this example form https://github.com/ngs/wiringPi/blob/master/examples/isr.c as he said for test use gpio mode 0 up gpio mode 0 down in terminal , I did this and it just print waiting... my question is , Is wiringPiISR working on orange pi one? If the answer is yes, what should happen in this example? If the answer is no ,what can use instead of wiringPiISR ?

Hi, I have recently called apt-get upgrade (with my regular installation and also with a fresh one) and after trying to extract armbian-firmware (I think it was that name but I'm not totally sure) dpkg returns an error. All other packages are installed without error. Unfortunately the OrangePiLite then hangs on next boot. I guess this package is broken in the repositories? Has anybody else encountered this issue?

Hello, I have a cubieboard A10 connected to a SSD drive (transcend) trough the sata port. I use it as a headless server to run transmission, nfs and barracudadrive. The board runs from a sandisk 16gb µSD card, the data is on the SSD (with dynamic links). I use the standard legacy armbian image without DE. The SSD is powered by the board and the board is powered with a 2A 5V power supply, comming from a sony psp. If I measure the powerconsumption at the wallsocket, I measure 6W in idle and it goes up to 10W in use (so just enough for the power supply). Because there is a specialist here in powerconsumption (tkaiser), I wonder if it isn't possible to make …

Hi, I installed armbian onto eMMC. Frankly, I expected better results. Please anybody confirm what I understood. 1. The sequence reading speed is 70MBytes/s. 2. The sequence writing speed is 10MBytes/s. 3. eMMC is not optimized for random operations. 4. When writing operation is performed, the system gets VERY SLOW to respond. And the couple of questions. 1. What utility and where to get to benchmark disks well? 2. Will USB SSD perform with better performance than eMCC? Thanks a lot in advance and hope to see this in the FAQ. Dmitry

Hello. I am using baresip for SIP communication. I have faced a problems with audio USB adapter (http://www.hardkernel.com/main/products/prdt_info.php?g_code=G141629380416) with C-media chip. I have set it as default sound card. I make a call using baresip. Until I answer the call on another device it works, it rings. But when I answer, kernel errors occurs and Orange Pi hangs (cannot do anything): Message from syslogd@localhost at Sep 18 11:20:18 ... kernel:[ 226.378730] sunxi oops: enable sdcard JTAG interface Message from syslogd@localhost at Sep 18 11:20:18 ... kernel:[ 226.380906] sunxi oops: cpu frequency: 1008 MHz Message from syslogd@localhost at…

I've just installed the Armbian 5.20 in the Banana PI M2. No boot. The message "Waiting for PHY auto negotiation to complete .....Timeout! Could not initialize PHY ethernet@01c30000" shows up over and over again and the boot freezes in sequence. Somebody knows what is going on?

I've try to upgrade my pi to newest version of the system yesterday, but FAILED for both apt-get upgrade or by download and write the newest image. Here is my working log: 1. apt-upgrade from armbian 5.14 image - error message indicate there's error during the apt-get update process - reboot, the boot screen shows no bootup message, than begin the TFTP startup process - wait until TFTP timeout, the system halt. 2. download and write the newest **Armbian_5.20_Bananapipro_Ubuntu_xenial_4.7.3.7z** - can be startup with the boot screen, both power led and disk io led (green led) work as expected - system halt after a few second, the power led …

Hi, I'm trying to install Armbian 5.20 vanilla kernel to eMMC on my Opi PC+. After nand-sata-install finishes I shutdown the Opi PC+ and power it back on. At least, I enable the power, I don't see anything happening in minicom on my pc. Only when powering it with a microsd in the slot (with armbian) will the uboot show in minicom on my pc. Doing a nand-sata-install with 5.14 legacy worked. What am I doing wrong (especially seeing nothing after a reboot with my ttl-to-usb connected is a bit strange for this noob)?

I disconnected the Beelink X2 and connected it again and now there is no picture on screen. I tried several HDMI cables and tvs. What can I do so the player will work and show the picture? I tried flash the x2 firmware the flash was successful but still there is no picture. edit: now the red light on the x2 that shows the x2 connected to the electricity turns off and doesnt stay on like before.

Hello, I have an Orange Pi+ 2 and Orange Pi+ 2e. I use Armbian, updated to 5.20 with these commands: sudo apt-get update sudo apt-get upgrade so I rebooted and can't start. What can I do? Thanks

First of all ('Boring' alert!): outstanding job with the new updates. It must be lonely at the top. Kudos! Then (just curious!): is there any particular reason known that the amount of memory is an issue for GLshim? Then secondly: I do have an orange pi + (H3, 1 GB memory, Mali400)... according to the changelog GLShim is not in... For me it does not make sense... Regards, Makama80

Have anybody tried to setup Amazon Alexa on the OpiPC?

Hi, my configuration is: Asus 5V 2A power adapter with usb to 1,7mm cable, Kingston microsd 16GB class 10 with Jessie desktop I can SSH the OPi so I can use H3disp output to HDMI (TV) works fine output to HDMI -> DVI to PC monitor works fine is it possible to use HDMI adapter to DVI, DVI to VGA and get the image to a PC monitor via VGA? i tried it using -d switch but nothing shown on monitor, do I need any special command? or this is not possible at all? please advice, Thanks

Hi there, I installed the Desktop version of Jessie, it was working good, but after I wanted to check the Server version too "Armbian_5.14_Orangepione_Debian_jessie_3.4.112.7z", but it just wont boot up, no Led's glows up on the board. Tried more times to install on different MicroSD cards, but I got the same non boot results. Just to mention that the Desktop version is working on all MicroSD cards I tried! Thank you for your answer! Kind regard

Hi guys, i've the following problem in my attempt to customize/study armbian: - succesfully compiled Armbian_5.17_Bananapim2_Debian_jessie_4.8.0 on Ubuntu 16.04 with default config; - burned image on SD card, (on the same card burned with Armbian_5.14_Bananapim2_Debian_jessie_4.6.2_desktop and the system boot is ok) - the board enter in this reset loop: U-Boot 2016.07-armbian (Sep 11 2016 - 10:06:05 +0200) Allwinner Technology CPU: Allwinner A31s (SUN6I) Model: Sinovoip BPI-M2 DRAM: 1 GiB MMC: SUNXI SD/MMC: 0 *** Warning - bad CRC, using default environment HDMI connected: Setting up a 1680x1050 dvi console (overscan 0x0) In: serial Out: vga Err: vga…

Hi there, As the topic title says,... Is there any available option to install/setup Domoticz server onto Orange Pi Box using Armbian Desktop or Server version? Thank you! Kind regards

Hi, I received a Banana Pi M2+ board on which I installed ARMBian. Their is only one problem for sound. Audio out is only available on HDMI. As I will use this board with no display, keyboard and mouse connection how may I get this board playing sound ? Two ways but I do not know which one is possible : 1) does it exist an HDMI to sound 3.5mm jack adapter ? 2) which USB bluetooth dungle works perfectly on ARMBian I may use to pair this board to a portable bluetooth speaker ? Sincerely thanks. Have a nice day. Miguipda ;-)

Hello, I'm trying to get a opi+2e to output something on my HDMI TV without success. The TV is a 10yo Thomson intuiva 27LB130S5 (1280x720, should be capable of 720p / 1080i) I tried android on eMMC, worked OK. Installed Armbian_5.14_Orangepiplus2e_Debian_jessie_3.4.112_desktop on a microsd. During install there was some console output to the display (a bit mangled), and after the reboot, nothing. I got SSH over eth access. I disabled nodm service, rebooted to have FB console only (easier to debug, or so I thought) Still nothing. Tried h3disp on a few resolutions (-m 6, 5, 4, 2) with a reboot between each one. None gave me anything …

Hi, I yesterday built a new image for my A20-OLinuXino-MICRO board (Armbian 5.17 Jessie with kernel 4.7.3) At first boot, everything worked fine. I could manage to connect through SSH and changed root password and add new user. However, avec adding a Hard Disk (on the SATA connector) and reboot, I could not manage to connect via SSH So I tried the serial (UART) connector. After some tries and a non responding console (I could see no kernel messages at boot to I had to change the verbosity), I finally succeeded in booting with a console prompt on serial connector. But... The keyboard is not responding on that serial connector. After a few tries,…

Hi Everyone. I have been looking for a way to connect this keypad directly to my Orange Pi PC+ directly through gpio without resistors. https://www.adafruit.com/product/1332 I also need software (hopefully either bash or python) to read a key press and then either run a script or perform a command. If anyone here done this or even connected 1 switch to gpio (without resistors), could you please post the solution or a link to follow. Thanks. V

Hi Few days ago i've upgraded by armbian to the newest release version 5.17? from 5.11. The problem is, that minidlna DLNA server is only visible for few minutes after the service is started. Later i need a restart the service to make it visible for the new clients. The strange is that when i don't exit/shutdown the client, after the server discovered, it stays visible and works perfectly. But i want to make it visible for a newly started client, i need to restart the service. It doesn't seem to be client problem, as the same happens with my samsung smart tv, and a windows pc with foobar 2000 dlna plugin. What's the problem? (it maybe a broadcasting problem)

Hi all I need a bit of assistance in installing OpenMediaVault on the Cubietruck. I'll admit I tried this a while back, so I'm coming back to this to try and use my Cubietruck as a mini NAS. Tried to install using the instructions over at the debian site, but after the install, the web interface showed lots of errors and it wouldn't work. Done lots of googling to try and find further information but I'll admit I'm a bit vexed. Does anyone have some idiot-proof instructions or a prebuilt image they could provide to a bit of a linux newby? thanks in advance -matt

Help please! I have a bp2 which was bought almost a year ago, and use Armbian_5.14_Bananapi_Debian_jessie_3.4.112.raw as the image for couple of months. Today, I'm try to upgrade to the Armbian_5.14_Bananapi_Ubuntu_xenial_4.6.2.raw image, but the pi can't boot at all. What I do to prepare the sdcard with the following procedure: 1. remote the old partitation, and create a new fat32 partitation 2. dd bs=1M if=Armbian_5.14_Bananapi_Ubuntu_xenial_4.6.2.raw of=/dev/sdc; and sync 3. mark the written partitation as bootable with fdisk ps: I'm using fish shell, and the syntax for the dd command is valid So, what's wrong with my steps? How can I troubleshoot? …