Allwinner sunxi

I'd like to use Orange Pi PC as a HID keyboard USB gadget/USB device. There is a tutorial on link here but it makes Orange Pi into a serial device. I want a HID device (keyboard).

Hi I am new in the forum and the happy owner (as of yesterday) of an Orange Pi Lite. Nice little board. I managed to install Armbian server, configure Wi-Fi upgrade and install apache / php and mrtg. I also was able to enable one wire protocol to play around with a DS18B20 thermometer. My idea is to create an automated garden watering system with nice stats (graphs) I already have a 4 channel relay board (to connect solenoid water valves), a DS18B20 to sense temperature, an LDR to graph sunlight hours and 4 hygrometers --moisture sensors--. Those I want to connect through an I2C ADS1115 ADC module (which I also already have). …

I got an Orange Pi PC with Armbian Ubuntu Desktop installed. It runs perfectly fine. 1080p resolution, sound, ethernet, browsing, what-have you. It can even play x265 videos flawlessly (which is why I got it for as my RPi3 can't). Highest temp is 46C so far (with or without a heat sink and no fan). Anyway, I've updated and upgraded and then installed Kodi. My media is on my NAS, so I input my SMB info, and it connects fine. But as it reads the media, Kodi just shuts off on its own. No crash report or anything. It just closes and I'm back on the desktop. Re-opening it starts Kodi up for a sec and then closes itself. Deleting the user folder under a Kodi directo…

I have a device based on an Orange Pi PC. I want to add a 7 inch touchscreen display in a case. This is the kind of thing I'm looking for, but I'm not wedded to that one. I just want something that's known to work reliably. Thanks in advance for suggestions or guidance.

We have deployed the zero for an integrated MCU on one of our products, and in rare occasions we are experience random lockups of the MCU (possibly related to overheating). Its pretty much impossible to debug this since it happens very rarely, but we are trying to mitigate all possible causes. The MCU is controlling a bigger and more expensive board and a fan. If there are internal failsafes that are being triggered by the MCU and locking it up (like temp) we want to disable as many of them as possible (we would rather have the MCU burn up than our main board). Anyone have any insights on orange pi zero OTP or OCP in kernel or uboot parameters we can disable?

As the title says. I can not get PWM to work. I can type gpio mode 2 pwm and no error. But when I try to access it from Klipper (3D Printer Software and Firmware) it won't work. However if I use gpio 3, in software, gpio 4 turns on. Please help me out here. Thanks, Kevin

Hi I want to use my orange pi zero to stream music from my NAS and some internet radio stations. I want a good remote control from my phone so I want to use yatse to control Kodi. I installed xfce4 and vnc and I am able to connect to the desktop environment. I then installed kodi but it does not work: Xlib: extension "RANDR" missing on display ":10.0" I checked and randr is actually not missing, just not loaded. I tried to get it running for the past two hours but no luck. I am not very familiar with linux so I am stuck at this point. From what I read it must have something to do with the graphics adapter drivers. Any help would be ap…

Hi, I have noticed very strange behaviour of my OrangePi PC Plus. Device is connected to internet via Wifi. After successful connection, device is connected to VPN service. A cron script is checking every minute if VPN is working, and if not, it is restarting connection. On every hour, Network Manager is being restarted (you will see why is that so later). On every minute NTP is querryed for time synchronisation. After VPN restart or rebooting of device, device sends an e-mail notification via GMail. On eth0 there is DHCP server running (dnsmasq), which is providing internet to a device connected to OrangePi. So basically, you plug in ethernet cabl…

The translation was done by Google Hello friends, my hardware: Orangepi pc plus dac-pcm5102mk-i2s. 3.5 "touch display So far I have the system in eMMC (ARMBIAN 5.60 stable Ubuntu 16.04.5 LTS 3.4.113-sun8i) and optionally on 16GB uSD card (ARMBIAN Debian GNU / Linux 8 (jessie) 3.4.113-sun8i). In both cases, an xfce desktop is installed. The setup of the DAC I have after the tutorial I2S on Orange Pi H3 by Da Alchemist, February 29, 2016 in both Debian 8 and Ubuntu 16.04. Works well. I installed the display after the hints from How to use Touchscreen + LCD on H3 devices by kutysam, July 31, 2017. It claps with the display of the desktop, but the touch …

Hi I would like to ask you can I connect my NanoPi Neo Core 2 (Armbian) with LCD TFT 3.2 (320x240)px by GPIO and SPI. RPi driver module LCD-show is nor response and don,t work. Anybody has experience or know how to do that. Is it possible.

Hi all I have a banana pi running armbian. After the update to kernel 4.8.4 I am experiencing problems in enumerating USB device during boot (meaning device connected before powerup) I get errors like: [ 6.572517] usb 4-1: not running at top speed; connect to a high speed hub [ 6.578537] usb 4-1: unable to read config index 0 descriptor/start: -61 [ 6.578547] usb 4-1: can't read configurations, error -61 [ 6.789488] usb 4-1: new full-speed USB device number 4 using ohci-platform [ 6.848598] usb 4-1: not running at top speed; connect to a high speed hub [ 6.853598] usb 4-1: unable to read config index 0 descriptor/start: -61 [ 6.853620] usb 4-1:…

Hi all Does anyone recall if with kernel 4.9 it is required to put some patch for enabling power on the USB Host port of BananaPi? I am using vanilla kernel in another project, (LEDE) and when switching to kernel 4.9 I don't have any power from the USB port The dts is the vanilla one and AXP20x power driver is enabled Thanks!

board in WIFI mode phy#0 Interface wlan-ap ifindex 3 wdev 0x1 addr 02:81:1d:98:1c:bc ssid tomesh-8583 type AP txpower 12.00 dBm Drivers seems to crash as soon as i try to associate the first device with it Any one know what could be causing it? hostapd.conf interface=wlan-ap hw_mode=g channel=11 auth_algs=1 wpa=2 wpa_key_mgmt=WPA-PSK wpa_pairwise=CCMP rsn_pairwise=CCMP ssid=tomesh-8583 wpa_passphrase=password123456 [ 40.084416] Unable to handle kernel paging request at virtual address e1f27e64 [ 40.091697] pgd = 1…

Hi, I have Orange Pi Zero v1.5 with Armbian Buster (mainline kernel 5.4.y) and I would like to use the serial_rs485 struct from user-level. It is possible?

Hi, How to build the Phoenix image from the Cubieboard2 NAND-flash? If anyone have idea I would appreciate. regards, Rassul.

It has debian 8(jessie) server version 3.4.112-sun8i on it. It is updated to the latest version(apt-get update, upgrade). Caps Lock functionality works, but the light on the keyboard does not light up. I tried the keyboard on another computer, tried different keyboards. I am using this to get back the cursor. I found it here: http://forum.armbian.com/index.php/topic/1246-terminal-console-cursor-disappeared-after-apt-upgrade/ Could it have caused it? Anyone having the same issue?

Hello, I try to setup my Orange Pi Lite with a thermal printer (http://www.ebay.de/itm/122418910118?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT). With my Arduino the printer works perfect, so it is actually ok. I just can't figure out how to use the ttl connection. I installed pyA20 and try to implement a kind of SoftwareSerial and it didn't worked really well: #!/usr/bin/env python """Basic blinking led example. The led on A20-OLinuXino-MICRO blinks with rate of 1Hz like "heartbeat". """ import os import sys import time if not os.getegid() == 0: sys.exit('Script must be run as root') from time import sleep from pyA20.gp…

I was configuring onboard wifi of OPI ZERO, rev. 1.1 with the provided tool armbian-config. On one board it went just OK, on the second it froze, so I manualy powercycled the board. After that the board does not boot. I connected the serial console and here is the output I got: U-Boot SPL 2017.09-armbian (Nov 20 2017 - 02:53:16) DRAM: This is my first time troubling with u-boot, so I have no idea what this means, but it should give me more output. I will try to look, if there is 1.5V at the 1_5V pad.

Hi, I use orange pi pc plus with armbian bionic, firstly I use it with a SD card and the temperature its around 30 centigrade degrees, its ok. Then I use EMMC without SD card and the temperature increases to 51 degrees (I think it´s very high), they are some way to use EMMC without the board increases the temperature?? Best regards, Nelson

Hi , there I am trying to write a program which will detect the presence of SD Card in Nano Pi M1 plus device. There are many ways to do this either by doing fdisk -l or looking into /dev/mmcblk* . But I want to keep running it in a loop and doing fdisk -l and grep doesn't seems an appropriate way. Can the insertion or removal of SD cards be checked via Hardware Interrupts? Plz. help me I am a newbie. Thank in advance.

Hi, I would connect a 7" HDMI 1024x600 Touchscreen display (like waveshare or else) on Orange Pi 3 (as a raspberry). Latest armbian version for H6 CPU support this display ? If a need to use a 7" touchscreen display on Orange Pi 3 how can I do ? Thanks

Hi, who knows how to fix the problem of the displaced screen on the right? This is how Armbian appears with the latest build https://dl.armbian.com/orangepi3/nightly/Armbian_5.90.190705_Orangepi3_Ubuntu_bionic_dev_5.1.15.7z and this is how it appears to me with an old build with kernel 5.0.7, so it's not the monitor's fault Regards

I'm not familiar with the a64 graphics driver and some tty graphics software of mine is failing on Armbian Ubuntu Focal after working fine on the Bionic image. Earlier I was able to mmap() /dev/fb0 to display graphics in a tty. On Focal 20.04, running linux 5.4.43-sunxi64 , mmap() on /dev/fb0 is failing with EPERM (operation not permitted). Is this new error something anybody knows about or could give a link to find a possible driver change that's responsible? It seems there might be a few different video drivers on this system and I haven't looked at them before. /sys/class/graphics/fb0/name contains sun4i-drmdrmfb /sys/class/gr…

Hello, I am trying to communicate using UART PORT. I have connected to 8, 10 and GND pin. Also I enabled UART3, but it doesn't work. Any solution? Thanks !! Enviado desde mi iPhone utilizando Tapatalk

Good night, I have the sound problem but with hdmi audio, de default is the 3.5 mm audio jack, then I looked for the asound.conf in /etc, then I found that this file doesn't exist and after that I've created it with the following content: pcm.!default { type hw card 1 device 0 } ctl.!default { type hw card 1 } the problem is that even created this way the sound output still being the 3.5 mm jack and I don't know if I need to change some setting to mpv player to output the sound through hdmi. What else can I do to change the sound from audio jack to hdmi?

This seems like a really simple problem, but I can't find any pointers on any forums. I am running a NanoPiNEO2 (Allwinner H5) using the latest Armbian build DISTRIB_ID=Ubuntu DISTRIB_RELEASE=16.04 DISTRIB_CODENAME=xenial DISTRIB_DESCRIPTION="Ubuntu 16.04.3 LTS" I am trying all ways to save power. For most of the time, I do not need to use the Ethernet interface (I am using the USB interfaces for comms). I have tried all the obvious commands such as ifdown, and explored ethtool, but nothing I do makes any difference to the current consumption of the device. I expect i am missing something obvious - any help gratefully accepted.

So trying to run some GPIO interrupts using wiringpi. Using the wiringPiISR function and setting and interrupt handler seems to work, but as soon as the first interrupt happens, the handler gets stuck in some sort of loop and just get infinitely called. Pretty sure this is some bug in sys, since the wiringPiISR function just uses sys gpio calls to do the interrupts. Could be wrong and just be an issue with how wiringPi does it. Either way has anyone come across this and know of a workaround to fix this?

So I got a new orange pi 3 lts and I have installed armbian bullseye on it, but I can't seem to make it work with my crt TV like my raspberry pi 3 b+, even though I am using the same cable and TV and it still works with my raspberry pi I have tried: -Changing the resolution -Changing the aspect ration But nothing works What am I supposed to do to make my armbian work on my CRT tv??

Hi all, I've installed the latest jessie Mainline 4.9.7 on a cubietruck and when I give sudo hwclock I get no printout and if I run hwclock as root I get segmentation fault Does anyone has an idea what is wrong ?

Hi! How to install postgresql-10 in ARMBIAN 5.36 (BananaPi)?

Libre software refers to the free software foundation's guidelines. Can you make an entirely libre software armbian version work on the orange pi one or other orange pi computers? How good will it work? About the orange pi one which devices will not work if only libre armbian software is installed? Notice this https://www.kickstarter.com/projects/bootlin/allwinner-vpu-support-in-the-official-linux-kernel/description If orange pi computers can work using libre software armbian, then how do they boot? Do they use uboot? Thanks.

Short issue description: sometimes after pulling a USB device out it makes OPi3 USB host controller stuck. One or more USB ports are getting unresponsive (sometimes all four of them) and no messages in dmesg about connection/disconnection. No matter what device is used. This thing happens only on the first host controller, the second rear one is functioning and responsive. It happens more often if we push in and pull out four devices in a short period of time. Wherein /sys/kernel/debug/usb/devices is stuck too, we cannot read the info from it and all the utils (vi, cat, etc.) are getting the D state (uninterruptible sleep). "lsusb" is also not working, but can b…

Hello, I'm using a BananaPi and just tried the latest version (10.6.2015, Linux 4.0.5) of your great distribution. Unfortunately, support for ath9k_htc based USB Wifi adapters seems to be missing, which is crucial for me. (ath9k_htc works great using free and open source firmware.) Could you please add support for this kind of hardware for future releases or give me a hint how I could add support to your existing images? Thank you and kind regards, LINMOB

Maybe this is not strictly related to Orange Pi PC but a few weeks ago I had problems with booting my device - mainly OpenELEC and I had to debug it somehow using serial port and the terminal. Unfortunately my PC is rather far from the place where I keep OPiPC. So I was forced to prepare separate device - cheap STM32 MCU based terminal display with 2.2" LCD screen directly supplied from Orange Pi PC 3.3V. It can be used also with other devices which allow serial console debugging. Watch below videos for more details and the code: Maybe someone finds it useful.

Hello! Can anyone help me to set up my Orange Pi one ,that I could use gpio's with node-red? I am using armbian 5.22. Recently I am trying to manage my OPi One to work with Node-Red. Today I finally set it up and was able to start Node-red. After that I tried several hours to manage GPIOs ,but nothing worked. Is there a short version how to manage gpios to get them working. So today I installed nodejs 4.xx, npm@2.x. After that I installed wiringPi from github, then I added to node-red -> npm wiring-Pi and modified settings.js , after that I tried npm -> wiring-op and still nothing. I my experimentations today I started 3 times with cleans jessie install…

Hi, I did read a lot about temperature and power consumption on this forum. Most is about bad parameters for the Orange Pi H3 boards. I use armbian 5.25 stable with 3.4.113-sun7i kernel. On both i run this same version, the only difference is that i use an other script.bin on the orangepi. The script.bin who is in the distrubution. I dont use a heatsink on both. I noticed the following On the Orange Pi: Load1 is max 0.50 with 2 values of 1.00, avg 0.20-0.25 Load15 is between 0.08 and 0.14 The temperature is between 49 degrees and 52 degrees Celcius The PMU current is between 400 and 800 mA PMU Consu…

kernel: "Linux orangepizero 4.13.16-sunxi #20 SMP Fri Nov 24 19:50:07 CET 2017 armv7l armv7l armv7l GNU/Linux". I have tried this document, http://opi-gpio.readthedocs.io/en/latest/api-documentation.html#pull-up-pull-down-resistors I am using pin 7 (GPIO 6) and INPUT mode, but it not working, however I got push signal, but I have not push it, why? The following is my python code. import OPi.GPIO as GPIO import time channel = 7 GPIO.setmode(GPIO.BOARD) GPIO.setup(7, GPIO.IN) while True: time.sleep(0.5) print GPIO.input(channel)

I'm trying to configure the RTL8189FTV module on an Orange Pi+ 2E in SoftAP + STA mode so I can use it as wifi hotspot. According to this old document from Realtek (http://www.ofeixin.com/downloadRepository/8da8dda7-6721-4ac8-a7db-47cc4d9b218c.pdf), it's possible to do so using an RTL8189ETV, so I'm assuming it's possible on the RTL8189FTV, too. The default driver doesn't allow concurrent connections like this, tho, so it must be recompiled. I downloaded the source recommended on the sunxi wiki (http://linux-sunxi.org/Wifi#RTL8189FTV): git clone https://github.com/jwrdegoede/rtl8189ES_linux.git cd rtl8189ES_linux git checkout -B rtl8189fs origin/rtl8189f…

hello i trying and i cant make kedei 3.5 inch ver.6.2 work on orange pi pc.i am new in that. can someone put tutorial or something pls ? thank you.

Hello, When I can backup my system who is in the emmc ? in another sdcoard or in usb key to image file ? Thanks

I've got a fresh Orange Pi PC Plus 2 with the relevant Armbian loaded onto a new card. It seems to output just fine to HDMI on my workbench at home, using a relatively new monitor and a direct HDMI cable, but when I try other monitors I get inconsistent results. One is a Quimat 7-inch display that just shows a white backlight when connected to the OPi. However that display has issues with other boards so I'm not entirely worried about it. But the other display is a fairly modern ViewSonic monitor that exhibits a more confusing behavior. The monitor only has DVI/VGA so I'm connecting to it through a passive HDMI-DVI adapter. When I boot the board, the POST screen shows up …

I've read this and it surprised me noone mentioned e2image. I'm using armbian orange pi pc build. The fs is stock ext4 hence why I stick to e2image below. It is not about cloning a live system, hence the sdcard is plugged into my PC. Fdisk shows a single partition at 4M offset. First I backup the partition table and bootloader dd if=/dev/sdX of=offset0.img bs=4M count=1 Next I backup the single partition with e2image into a qcow2 image e2image -Qa /dev/sdX1 part0.qcow2 qcow2 only keeps used blocks. My partition size is 14.7G, space taken is 12%. part0.qcow2 file is 1.7G. Done with backup…

Hi, I use a Cubietruck 3 and the last Debian "Armbian_5.25_Cubietruck_Debian_jessie_default_3.4.113". 1° When i'm sart for the first time, It's impossible to reboot or halt the cubietruck. The led Green and blue flashes always. I must I have to remove the power connector for a reboot 2° Idem whem i have make an update and a upgrade 3° When creating the account at setup, I want to use "ac-news". The created account is actually "acnews" without the "-". Before posting, I tried several times the installation by writing a new image on the SD. I always have the same worries Thanks François A track: if I make a first installation with an Armbian_5.20_Cubietruck_D…

HI! Does anyone have experience with WiFI on Orange Pi Zero Plus 2? I tried to use image Armbian Legacy 3.4.113 for NanoPi NEO Air, (hardware is same H3, wifi AP6212) without success. No any wlanX interface. Thank you for your help!

I'm testing the nightly image: Armbian_5.32.170704_Nanopineo2_Ubuntu_xenial_dev_4.11.8.img I read somewhere that the NanoPi Neo2 has a shutdown issue where it reboots. This was my experience (serial console) `shutdown -h now` ends with [ OK ] Reached target Shutdown. [ 59.809788] reboot: Power down INFO: PSCI Affinity Map: INFO: AffInst: Level 0, MPID 0x0, State ON INFO: AffInst: Level 0, MPID 0x1, State ON INFO: AffInst: Level 0, MPID 0x2, State ON INFO: AffInst: Level 0, MPID 0x3, State ON Maybe there is a watchdog timer (that resets the CPU if some ticker stops or something) that needs to be disabled? …

As I told on another topic, yesterday I installed Armbian 5.90 buster 4.19.57 on my OrangePi One. Now, when it boots, all the output text goes to the bottom line of the screen, with each line overwritting the previous one (no scroll). Then it asks for username, and when I type it it asks for password, overwritting the username I typed. And it probably displays the wellcome banner, but I just see the last line of the banner. Once logged, I have to type "clear" and then I can use the full screen, and it scrolls. That happens on the console, if I start a new session from another machine (using PuTTY) it works fine. My password …

I have a raspi hat (rak2245) that has 2 versions: a pi-hat version that has a 40 pin-header on it for raspberry pi's , but also a smaller stamp edition. It uses spi and uart to communicate with the pi. I have it running without issues on my orange pi zero, even though the pinheader is a little too large. And via a breadboard I can access all pins just fine. But since I am making my own PCB anyway, I am interested in using the stamp version. The only difference between the stamp and the pi-hat version (aside from the form-factor and pin-out) is that the pi-hat version has an additional eeprom chip to tell the rapsberry pi about the function of the pins apparently. Now…

Hello! I just installed armbian 5.38 and updated it (apt update, upgrade...) so i'm use last packages on the board. When i use VLC via HDMI output, it works like a charm, but i need to use VLC via TV out jack. When it on TV out i see freezes on image and image on fullscreen VLC placed not in center (right down side) vlc starting by shell script: #!/bin/bash #echo xterm >> .xinitrc #startx #echo $DISPLAY #:0 sed -i 's/geteuid/getppid/' /usr/bin/vlc startx /usr/bin/vlc -q --no-osd -L -f --no-video-title-show --no-qt-error-dialogs --x11-display :0 -V glx http://*******/index.m3u8 2&>1 >/dev/null & if i delete option -V glx from co…

Hi, I want to expand my NanoPi-NEO2 more uart ports through I2C, so I make a choice to use a sc16is750 module( just like sparkfun sc16is750 ). Below is all of my system information: pi@nanopineo2:~$ uname -a Linux nanopineo2 5.4.20-sunxi64 #20.02.1 SMP Mon Feb 17 02:37:37 CET 2020 aarch64 aarch64 aarch64 GNU/Linux First step ,I edit a device tree overlay for the sc16is750 named sc16is750-i2c.dts as below: pi@nanopineo2:/boot/overlay-user$ sudo nano sc16is750-i2c.dts /dts-v1/; /plugin/; / { compatible = "allwinner,sun4i-a10", "allwinner,sun7i-a20", "allwinner,sun8i-h3", "allwinner,sun50i-a64", "allwinner,sun50i-h5…

Hi all, I'm puzzled how everybody is building clusters of cheap SBC's, but nobody is implementing HA, redundancy, resiliency, failover, etc. They're just SBC's networked together. The SBC's are underprovisioned for Ceph, so I think that even if a Ceph configuration was managed to be shoehorned in, it wouldn't perform well. I don't know if DRDB is an option. How are people actually doing implementing real clustering technology on Orange Pi, for example? I'm using OPi+2E. Kind regards, Andrew

I cannot get the screen to rotate 90 or 270 degrees. Inverting it works like it should, but not "sideways". uname -a: Linux orangepilite2 5.4.20-sunxi64 #20.02.1 SMP Mon Feb 17 02:37:37 CET 2020 aarch64 GNU/Linux xrandr --version: xrandr program version 1.5.0 xrandr Screen 0: minimum 320 x 200, current 1024 x 768, maximum 8192 x 8192 HDMI-1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 0mm x 0mm 1024x768 60.00* 800x600 60.32 56.25 848x480 60.00 640x480 59.94 /etc/X11/xorg.conf.d/01-armbian-defaults.conf: Section "Monitor" Identifier "Monitor0" Option "DPMS" "false" Option "Rotate" "right" EndSection Section "Server…

History work: started my work from raspberry pi but recently shifted to orange pi. On raspberry, me used teh UV4I server wif webrtc to broadcast video streaming and send controls through data channels from a web browser to control a robot. My application: So basically my application is a semi-autonomous car wif two cameras.me want to control teh car from a web browser and stream a video of both cameras on teh browser Issues: 1: On orange, pl broadcast streaming from USB cameras to a web browser? 2: Send controls from web browser to orange pi? 3: Teh UL4l drivers are not installable on an orange pi pc so need to find an alternate 4: halp to fi…

Hi, I always been an retrorangepi user for my Opi1. but the lastest retrorangepi is stuck at 4.1 (I try the 4.2 slim but it's too slim) and the 4.3 beta also if its named as full, lacks of kodi and many emulators. so, my thought is. What if I build my personal emulationstation + lastest kodi on top of lastest armbian? Can I install armbian and then emustation and kodi? Do I have to install all emulator one by one? or I could use retroarch? Can I setup armbian to boot emustation? I think could be a good thing also for study

Thought this might help other people, so I wanted to share: https://github.com/robbieh/Inky7-BananaPi

root@x1c:/tmp# diff -u m1plus.dts.orig m1plus.dts --- m1plus.dts.orig 2016-05-07 17:52:38.000000000 +0200 +++ m1plus.dts 2016-05-07 18:16:36.000000000 +0200 @@ -704,6 +704,13 @@ bus-width = <0x4>; non-removable; enable-sdio-wakeup; + brcmf: bcrmf@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + interrupt-parent = <0x3a>; + interrupts = <7 15 0x00000008>; /* PH15 / EINT15 */ + interrupt-names = "host-wake"; + }; }; usb@01c13000 { @@ -1081,7 +1088,7 @@ allwinner,pins = "PI4", "PI5", "PI6", "PI7", "PI8", "PI9"; allwinner,functi…

Hi, I have 5.25 without armbian updates - just Debian: Linux lamobo-r1 4.9.7-sunxi #1 SMP Thu Feb 2 01:52:06 CET 2017 armv7l GNU/Linux. When I boot the device, it comes up fine, gets its IP-Address on the WAN port. If I try to restart the network it will not come up, I can access via UART but no longer via Network. If I restart the network from the UART again with the same command the Network comes up. This is how it stops: root@lamobo-r1:~# service networking restart Warning: Unit file of networking.service changed on disk, 'systemctl daemon-reload' recommended. less /var/log/syslog | grep NetworkManager: Spoiler root@la…

I there im using orange pi zero for homeassisatnt and google assisatant since my card died i install this new version configured every thing but audio isn´t working! I fallowed this guide like before but no audio coming for my orange pi zer no recording either! I have activated analog audio I already have everything configured with homeassistant i don´t wanna configure all again! Can you please help me make audio work in this kernel or is impossible to do?

I'm using flir's usb 3.1 camera with OrangiPi 3. default value for usbfs_memory (/sys/module/usbcore/parameters/usbfs_memory_mb) is 16. I should change it to a 1000 to be able to use full size image acquiring. testing this number, the higher I set it the higher image size I can get until 256mb. above 256, max image size is aprox 3200x2736 pixels (I need 5472x3648). so I guess somewhere in usbcore / kernel there is additional limit. Liad

There are any chance to get running a graphical desktop ambient? I've read on the forum that the kernel need some mod in order to work... Anyone get it working?

Hi, I would like to run Armbian Stretch (mainline kernel 4.14.y) on Bananapi M1. Board has an issue - sd card detect pin is broken. In legacy kernel 3.4.y there was an easy workaround to change paramter sdc_detmode = 1 to sdc_detmode = 3 in /boot/script.bin file. How would I do this on 4.14 kernel which as I understand doesn't use script.bin anymore? I setup Virtualbox with Ubuntu 18.04 and I can compile image with default options. I only need guidance in what parameter and in which file to change.

Hi, I have compiled the FFmpeg version in "https://github.com/stulluk/FFmpeg-Cedrus" (great job !!) to get h264 hardware encoding on Olinuxino-LIME2-4G A20 board. My goal is to encode in realtime h264 with a low cpu load and to stream video with crtmpserver. The crtmpserver service runs fine, while FFmpeg exits with the following error: [cedrus264 @ 0x28cf680] VE Open error. I entered the following command line: root@lime2:/etc/campipe# ffmpeg -f v4l2 -s 640x480 -pix_fmt nv12 -i /dev/video0 -pix_fmt nv12 -qp 23 -c:v cedrus264 -threads 0 -b:v 1200k -bufsize 2400k -r 25 -vewait 3600 -an -f matroska - | ffmpeg -i - -c:v copy -f flv -metadata streamName=livestream…

I can not install the plugin because of the missing of linux-headers-4.8.4sunxi Did anyone tried to instll this on a banana pi pro

Is it possible to soft reset USB device/hub on legacy kernel? On x86 I used to use some C code (opening usb and sending ioctl USBDEVFS_RESET) but id does not work here on arm...

Hi, I see in the /usr/lib/armbian/armbian-firstrun script that it runs the command: update-rc.d ap6212-bluetooth defaults for nanopi neo air (and some other boards) However if I try to run this script sudo /usr/lib/armbian/armbian-firstrun start The result is: update-rc.d: error: unable to read /etc/init.d/ap6212-bluetooth setfont: ERROR kdfontop.c:183 put_font_kdfontop: Unable to load such font with such kernel version setfont: ERROR kdfontop.c:183 put_font_kdfontop: Unable to load such font with such kernel version setfont: ERROR kdfontop.c:183 put_font_kdfontop: Unable to load such font with such kernel versio…

I'm trying to stream audio from my windows pc to a orange pi running `ARMBIAN 5.30 stable Ubuntu 16.04.2 LTS 3.4.113-sun8i`, in the verbose output in the pc and in the orange pi shows that the connection has been stablished but it gets refused right after with no "explanation". I'm following intructions from this thread, it shows how to add the tcp protocol to pulseaudio in the orange pi and on the windows machine the audio is captured with linco and it streams with plink (putty command line interface). Why the connection would be refusing to stay connected? PS: in the installation process `/etc/default/pulseaudio` didn't exist after pulseaudio installation, but as i…

I have a question regarding the configuration of the /etc/asound.conf file... are there any changes in the new kernel that prevent this from happening? I've noticed that my USB audio card no longer loses its settings and its position doesn't change. However, to be sure, I tried editing the /etc/asound.conf file... but it turns out to be impossible 🙂 That is, after saving the settings in /etc/asound.conf... ALSA doesn't work! 🙂 Moreover, the blocking for certain selected devices doesn't work either. In my case, the blocking is: HDMI Audio... in the file: /etc/modprobe.d/blacklist.conf blacklist sun9i_hdmi_audio blacklist snd_soc_simple_card Are these changes rel…

I'm trying to get a 4K 5.5" LCD to work (only console mode needed ) . U-boot can get it on at the desired resolution : 2160x3840 ( yes it's a portrait mode ) and display correctly . Seems that U-boot is reporting the correct information to set up simpleFB , but I don't get any display after kernel loading . The display adapter (HDMI>MIPI) have 3 options ( switching between 3 different EDID ) , the 2 others are working correctly ( 1080x1920 , 1440x2560 ) . I 'm wondering if this is related to simpleFB limitation , or memory allocation ... problem is that I'm a complete noob ... I can provide any information needed as long as you tell me what…

Hi all! I have Orange Pi One with Armbian Debian 5.8.9-sunxi on board. The problem is that when I catch 2 kHz square wave with OPi gpio, I have very big delta between signals. If I use "interrupt both endges" parameter for gpio, time between signals must be 250 microsecs. But now it floats between 200 - 290 microsecs. And I have achive this result after some suggestions from other forum topics: using isolcpu=3, run c program on this cpu, use max priority, disable powersaving for CPU. I try to read with wiringOP lib, and directly from sysfs, but still have jittering about 90 us. Also I think, that I have not very bad results for cyclict…

After an "apt upgrade", the kernel was switched to "Linux 6.6.16-current-sunxi64" (Armbian 24.2.1 Jammy). On the WiFi side, no problem, but for Ethernet, it no longer seems to detect the link. So I downgraded to "Linux 6.1.77-legacy-sunxi64" with armbian-config. After this, the Ethernet works again. Do you have any idea where this could come from? And if this can be fixed in future versions?

Hi dear. I have some question about orangepi plus. I am using orangepi+ and The latest Armbian Debian Version was installed in emmc. and i have some BLE Module. but, when i add my module to gpio pin, i can see I/O Error..but it's not always, somtimes there is no error. and when i boot orangepi-plus, it is PULL-UP state. i don't know this reason, how can change default gpio pull-up or pull-down state? or you have some idea? thanks

Hey, I have one system completely new installed with Armbian Xenial and one system installed with Armbian Trusty (some time ago) and then done Dist-Upgrade. Now after upgrading both from 5.20 to 5.23 I checked the relevant packages and there are differences: Original Xenial system: root@cubietruck3:~# dpkg -l | egrep "armbian| linux-" ii armbian-firmware 5.22 armhf Linux firmware ii armbian-hostapd-xenial 5.14 armhf Patched hostapd for xenial ii armbian-tools-xenial 5.22 armhf Armbian too…

Lost the login motd following apt-get upgrade. Start-Date: 2016-05-08 10:52:11 Commandline: apt-get upgrade Upgrade: linux-image-next-sunxi:armhf (5.04, 5.10), linux-headers-next-sunxi:armhf (5.04, 5.10), linux-trusty-root-next-cubietruck:armhf (5.04, 5.10), linux-dtb-next-sunxi:armhf (5.04, 5.10), linux-firmware-image-next-sunxi:armhf (5.04, 5.10) End-Date: 2016-05-08 10:56:33 I imagine I have to reinstall a pam config file?

Hello, I've just purchased a PCduino3B. I installed Armbian (Jessie Desktop) on it. Since I've done this I have the issue of the HDMI signal dropping out occasionally. This has happened with 2 different HDMI cables and 2 different monitors (one an actual PC monitor, the other my Panasonic Plasma TV). Has anyone else come across this issue before? Is there anything I can check? Also I'm having trouble getting the wired network to connect using the WICD Network Manager (The Wifi connects OK). Is there anything I can check here? I haven't used Linux for many years and am very rusty on troubleshooting issues. Many thanks in advance for your help. No.42

Wondering if there's anything similar to retroarch or mednafen that'll work for armbian on a pcduino3? I can't get the former to compile/install and the latter gives me guff about not being able to find a GLX visual when it tries to load video. It's worth noting that I'm pretty green when it comes to Linux, especially when it comes to "exotic"/SoC builds. I have nothing against learning, but I've found the signal-to-noise ratio for this product in particular is very poor and a lot of the info is woefully obsolete.

Dear All, I am just trying to figure how to enable the UART3 to be a 4 wire serial port for Lamobo R1 board. As per the datasheet here, https://drive.google.com/file/d/0B4PAo2nW2KfnNTBaVENGeHZfSzA/view UART3 4 wire signals are routed to J12 connector. I was looking to modify .dtb file, when I realize there is a definitions for PH3 GPIO under DTB file such as usb2_vbus_pin@0 { allwinner,pins = "PH3"; allwinner,function = "gpio_out"; allwinner,drive = <0x0>; allwinner,pull = <0x0>; linux,phandle = <0x42>; phandle = <0x42>; }; PH2 is not defined, looking at schematic I cannot find how VBUS for US…

Hi, I have problem with my Orange Pi PC, where I installed Armbian_5.30_Orangepipc_Ubuntu_xenial_default_3.4.113. I install python-jabberbot and python-daemon to create daemon to do queries by jabber comunication protocol. When I am active on ssh I get answers from bot in seconds, but when I try get answer without, I must wait about 1-2 minutes to answer. Do you konow what may be responsible for this behavior? Best regards, Leszek Mazur

hi how can i enable the tv out in orange pi PC+, I need to do a kiosk mode thanks

I flashed the latest Armbian image on my NanoPi Neo 2 Plus's emmc. According to https://linux-sunxi.org/Linux_mainlining_effort I2S is not part of the mailinke kernel for H5. I can use I2S with Friendlyelec's images. However, I prefer Armbian. Is it somehow possible to use I2S with an Armbian image on this board?

I have an Orange Pi PC Plus (Armbian Bullseye CLI) that I'm using as a NUT server connecting to a Cyberpower UPS. Every 30 minutes the driver stops working and upon further investigation, this looks to be a USB connection issue. Is there some power-saving mode that would cause this or any other known issue? Thanks!

Good morning, I am using a version compiled with your script for Banana Pi M2 Berry to build a network HiFi streamer, and I am satisfied with it. I have installed LMS and Squeezelite, and everything is working great. Now I would like to add an Innomaker HAT AMP that has a 12V power connector that powers the Raspberry Pi at 5V via GPIO. The GPIO of the Banana Pi M2 Berry is declared compatible with the Raspberry Pi3, but I would like to be sure before frying the board in case it is not. Can you please confirm the total compatibility of the GPIO connector of the Banana Pi with that of the Raspberry Pi? Thank you for your response.

Hi, my old 1366x768 VGA LCD monitor was working with legacy kernel but after I downloaded and installed image with new kernel ( Ubuntu_xenial_next.7z) I could not get it to work with VGA output. When I set armbianEnv.txt with below, it still outputs to HDMI disp_mode=1366x768p60 video_mode=sunxi:1366x768-24@60,monitor=vga,hdp=0,edid=1 then I tried to add this with no luck. Both monitors go blank with it. extraagrs=disp.screen0_output_type=4 Is VGA supported with new kernel? If so, how ?

So I've installed and I'm running watchdog for some months now on BananaPi M1. I think it reboots the board when the default gateway has some issues. And that's fine, no problem with that. The board works 24/7 and it made 14+ days uptime without problems. But things have changed and the board reboots at least few times a day (seems I have a problem with armbianmonitor -u - the board rebooted twice before it ended). And here's the problem. watchdog doesnt log anything or I'm unable to find any usefull info. And watchdog.conf: (it seems that the board went offline - maybe internet connection issues, but I have another one running that's also "l…

Hi, I am trying to use below SSD1963 display modül with orange pi lite. is there anybody who can help me regarding wiring (SPI) and configuration https://www.buydisplay.com/default/7-tft-screen-touch-lcd-display-module-w-ssd1963-controller-board-mcu thanks, Mustafa

Hello, as already described in this topic: https://forum.armbian.com/topic/5619-nanopi-duo-sound-delay/ I have the same problem with delayed audio. -> " if I run speaker-test -t wav, instead of the sound playing "front left" it just play the work left, the continues playing "front left" correctly." When I run an audio-output-command two times, the audio is played well with the second command. But the greater problem in my case is a loud cracking noise when audio stops. Is there anyway to prevent the shutdown of the amplifier? I have to repeatingly start and stop audio files from nodejs. Thanks for your help, Jimmy

CPU load at 100 percent when using pleksmediaserver, I understand that it is not running hardware accelerated video? P.S in Orange pi plus 2 my equipment Orange pi plus 2 my equipment Orange pi plus 2

[H5: Nanopi neo core 2] I observe the UART Rx line to be influenced by the RTS line which I am using during sending. Is there a way to enable an internal pull-up on Rx so that this doesn't happen? I suspect it's the cause of communication errors that I observe. I confess that I am currently on a FriendlyCore 4.16 build, but I wouldn't expect such an issue to be too distribution-specific.

Good day! I connect the real time clock, made according to the instructions: RTC time is set I set the wrong time in the RTC, reboot. I look at the time in the system clock - at first not the right one, from the RTC, then they are synchronized and it becomes the right one. But in RTC, the new correct time is not recorded. What am I doing wrong? Or what else needs to be done?

Hello, We are using Orange Pi Zero with Armbian Bionic with Linux 5.4.20-sunxi armv7l GNU/Linux we are facing a problem, our orange pi heats up some time during processing and then freezes. We can ping the devices, but ssh stops working and all the application don't respond We followed the suggestion in thread: https://forum.armbian.com/topic/7848-mysterious-freeze-and-overheat-of-orange-pi-zero/?ct=1587196371&_fromLogin=1 But output of "armbianmonitor -m" is as below Stop monitoring using [ctrl]-[c] Time CPU load %cpu %sys %usr %nice %io %irq CPU C.St. 11:19:37: 1008MHz 0.18 6% 1% 4% 0% 0% 0% 76.4°C 0/4 11…

Greetings! It's not a influential or serious bug. I couldn't control the LEDs on Orange Pi One Plus by the command setleds, So I navigated to /sys/class/leds, and there are two items: orangepi:green:status@ and orangepi:red:power@. I tried to do echo 255 > brightness respectively and found that: orangepi:green:status@ controls the RED LED, while orangepi:red:power@ controls the GREEN LED. Please tell me if it's a minor bug or an intentional setting, thank you.

Hi I'm trying to cancel echo for orange pi pc plus any idea? Methods I've tried and failed so far https://github.com/voice-engine/ec Bu yöntem de doğru hardware bilgilerini bulmadım http://alsa-project.org/db/?f=d75c947d6147c6c00b31ba67bd1a6d62c010cfad

Greetings! I have acquired for cheap this old board. It runs an old Android (4.x) and I'd like to run Armbian on it, but lack the knowledge to do that by myself. The idea would be to start with booting a Linux a SD image, then attempt to install it on the onboard flash in place of Android. The board is not for sale anymore and the manufacturer removed any mention of it from their site, however Archive.org has a copy along with related files, manuals, firmware etc: https://web.archive.org/web/20140701064007/http://www.giadatech.com/index.php?act=pShow&id=36 The board presents itself when not in USB host mode as "SoftwinerEvb" which appears to be …

After some crashes and hard shout down my orange pi pc stuck on systemd services during boot after checking it seems file system has some problems. Then I try run fsck on root device by sudo touch /forcefsck but it did anything and dont run fsck after reboot no prompt on display and fsck log files are empty: cat /var/log/fsck/* any way I try to enable fsck by editing : nano /etc/default/rcS and set : FSCKFIX=yes and also try set in file system : tune2fs -c 1 /dev/mmcblk0p1 and all my attempts failed Igor please help

I've managed to get tv-out working on Armbian_5.24_Orangepizero_Ubuntu_xenial_3.4.113 with adding module tv to /etc/modules, but goes out of display. How can I change overscan to fit dispay to screen?

Hello. In my project, I want to use a linphone with support for the h264 codec. In repositories there is a version of linphone but without the specified codec. I tried to build a linphone from the source code, but failed. The matter is that the assembly of the dependent package belle-sip hangs (the assembly lasted 2 days). Tell me, does anyone have any experience in successfully building a linphone from git? Now I'm trying to build a linphone on the Orange Pi zero plus 2 H3 board.

Please help me build driver for usb wifi adapter Tenda u12 (RTL8812AU chip). Board Orange Pi+2 (Armbian OS https://dl.armbian.com/orangepiplus/Ubuntu_xenial_default_desktop.7z) adapter driver link http://tendacn.com/en/download/detail-2863.html build log with error Spoiler root@orangepiplus:/home/alex/Desktop/RTL8812AU_linux_v5.1.5_19247.20160830# sudo sh ./install.sh ################################################## Realtek Wi-Fi driver Auto installation script Novembor, 21 2011 v1.1.0 ################################################## Decompress the driver source t…

Hello All, First of all excuse me if such topic exist. I am using the Desktop version with legacy kernel provided from Armbian - https://www.armbian.com/orange-pi-plus-2/ I have tried to fix my overscan issues on my SHARP LC-42ADE-BK from the Aquos series. I had zero luck in resolving the issue. I used the documentation available on the Sunxi-wiki for FEX configuration ( http://linux-sunxi.org/Fex_Guide ) scavanged the internet for all kinds of information for configuring the scale/overscan etc. with u-boot/fex and such. Unfortunatly my TV does not let me choose Aspect ratio or such fucntions when my Laptop or OPI device is pluged with HDMI…

Hi. I am triyng to make Live Streaming for youtube with a HP Webcam, a Orange Pi Plus2e ethernet connected and Armbian but I can not make it work. I tried with FFMPEG and Aconv and I can see that the video is called, seems to work and I can see the statistics, but the stream does not arrive to youtube servers.... OBS Studio does not work. Any iddeas suggestions? Thank you in advance

Hello, I have an image based on Armbian 5.37 and I have noticed that after upgrading linux-jessie-root-lime2 from 5.37 to 5.60, the Lime2 was not able to get an IP for eth0. The only way is to execute dhclient eth0 I have noticed that a lot of file was added in linux-jessie-root-lime2_5.60_armhf/data/usr/lib/armbian and I think that one of them are responsible of this issue. Do you have any idea on how to fix that ? Thanks

Hi, I am trying to install the aircrack-ng driver via dkms from over here: https://github.com/aircrack-ng/rtl8812au When I change the Makefile to match my processor arm-sun50iw1p1 , I receive these compilation errors and do not know how to fix them. cat /var/lib/dkms/rtl8812au/5.2.20.2/build/make.log DKMS make.log for rtl8812au-5.2.20.2 for kernel 4.19.20-sunxi64 (aarch64) Tue Feb 12 21:53:55 UTC 2019 make ARCH=arm64 CROSS_COMPILE=/home/android_sdk/Allwinner/a64/android-51/lichee/out/sun50iw1p1/android/common/buildroot/external-toolchain/bin/aarch64-linux-gnu- -C /lib/modules/4.19.20-sunxi64/build M=/var/lib/dkms/rtl8812au/5.2.20.2/build …

Hi there, Orange Pi PC+, Armbian Stretch. What I want is to replicate current router (OpenWRT Barrier Breaker on TP-LINK MR3220 v1) on and Orange Pi. I use this router to "share" (using scp from host PC) an USB flash dongle (remote site backup). With its processor copying filer over WiFi SCP is terribly slow (1.2MB/sec). Network Manager "proposes" me to create an WiFi network, but with only NO security or only WEP. I use WPA personal. Configuration on router wlan0 as an AP (WPA), wlan0-1 as WiFi client (also WPA different SSID) with WDS enabled (to act as bridge member), eth0 as usual. All those 3 interfaces bridged together an …