Beginners

Hi, Today I updated to Armbian v25.2 and did the good old reboot after the update. I never had issue with runing the SBC headless, but since the update I get a blinking blue status LED for a couple of minutes until the system boots. When I tried to plug in a monitor to get an idea what is going on, the SBC boots normally. Monitoring with HDMI monitor plugged in: https://paste.next.armbian.com/ehirazemot Monitoring without HDMI monitor plugged in: https://paste.next.armbian.com/zaqipatoci Most notable difference are: [ 105.189528] meson-drm ff900000.vpu: [drm] *ERROR* flip_done timed out [ 105.189543] meson-drm ff900000.vpu: [d…

Hi, I am looking for a device that has good support for being WiFi access point and being in client (managed) mode at the same time. Which can you recommend?

This is likely a stupid question but I couldn't find anything about it. I have a NanoPi Neo2 v1.1 1GB where I flashed nanopi-neo2_sd_friendlycore-xenial_4.14_arm64. After that it has been upgraded to 18.04.2 LTS Ubuntu. Outputs: uname -a Linux NanoPi-NEO2 4.14.0 #82 SMP Fri Dec 8 14:33:14 CST 2017 aarch64 aarch64 aarch64 GNU/Linux cat /etc/os-release NAME="Ubuntu" VERSION="18.04.2 LTS (Bionic Beaver)" ID=ubuntu ID_LIKE=debian PRETTY_NAME="Ubuntu 18.04.2 LTS" VERSION_ID="18.04" HOME_URL="https://www.ubuntu.com/" SUPPORT_URL="https://help.ubuntu.com/" BUG_REPORT_URL="https://bugs.launchpad.net/ubuntu/" PRIVACY_P…

Hello. I have a new Rockpi 4C. I am caming out crazy because I cannot understand some hardware issues. If I use the 5.10 kernel all hardware is working less the GPU. The images are bad and the lines swing everywhere. But the CPU is pretty cool and sometimes the heat-sink became hot, but not forever. The resolution is only the 1024 X 768!! The bluetooth, with the kernel 5.10, is perfectly working. With the magic Armbian-Config utility I installed the legacy kernel 4.4. I switched on that kernel and the GPU is perfect now and I am reading what I am writing. BUT: The bluetooth service is gone. Definitively! The USB ports are gone too!! There is only one usb port wo…

I'm thinking of buying a WindowsCE/Android Netbook that uses a WM8650 processor and want to install Linux on it but the only images I could find were 10 years old ;/ If a stock image won't work then how hard would it be to compile it for the WM8650? I'm a complete newbie so please explain as if I'm a kindergarden dropout :)

I picked up an OrangePi PC Plus. I installed armbian Jammy which does not have the mt7921u driver. I would like to install the driver and was wondering the proper steps. I have done apt install linux-headers-current-sunxi cd /usr/src/linux-headers-5.15.93-sunxi make scripts Now is it a matter of grabbing the mn7921u source and compiling it? Thanks for any direction.

Hi , I am unable to boot my RK3568 board and cannot get it into MaskROM mode for recovery. The boot process fails with a "Synchronous Abort" in U-Boot SPL during DDR initialization. The device gets stuck in a boot loop. It starts DDR training (`ddrconfig:0`) but fails with a Data Abort exception. Standard methods to enter MaskROM /Loader have not worked. I have attached the full serial log (Boot_log.txt). Any guidance would be greatly appreciated. Thank you. Boot_log.txt

Hi all, Yesterday I make big mistake I executed command I have 8GB card, so all data are not lost. Is any way to recovery data? Thanks

Hi I am not very experienced with armbian/linux. I have a raspberry pi that is connected to a 4K tv via HDMI. When I turn the tv off and on screen resolution changes to 4K. I need to fix it to 1080p. I searched but couldn't find something I can understand. How can I do this?

I found my NanoPi Neo Air's could not list or connect to some wifi networks. Some investigating found this was because channel 12/13 are disabled by default. Nothing in runtime had any effect on the output of iw reg get as it should have. Patching in some firmware fixes worked for me. wget http://ftp.be.debian.org/pub/software/network/wireless-regdb/wireless-regdb-2025.02.20.tar.xz tar xf wireless-regdb-2025.02.20.tar.xz sudo cp wireless-regdb-2025.02.20/regulatory.db /lib/firmware/ sudo cp wireless-regdb-2025.02.20/regulatory.db.p7s /lib/firmware/ sudo iw reg set AU #Australia I can now connect to wifi channel 13. Now for my question: …

Hello, What is the correct way to set armbianEnv.txt values when the distro is being built? Specifically I'd like to set kernel verbosity to a non-zero value? There does not seem to be a skeleton file so is all content generated dynamically? TIA

I read that armbian bullseye for odroid HC2 is still unstable, while it is considered stable for other boards. Can somone explain the reaseon for this? Or point me to a place where this is discussed? If I knew what the reason is and it would be not important for my application, I could switch to bullseye now. Regards, jba

Hello! I trying use bluetooth on Orangepi with buildroot (without systemd, only busybox), but when I try connect my smartphone (or any device) and bluetooth, I receive this message: And after I can't connect anymore. Bluez return this message I wrote this script to init bluetooth: https://pastebin.com/gHdjHynT I using Orange PI zero plus2 with buildroot, bluez 5.50 Modules Bluetooth Thanks, and I'm sorry for english.

Hey guys, I see the HDMI audio is not supported in the status matrix. Do you know what is missing exactly? I read it predepends on DRM driver, do you know which part is missing? I read in #linux-sunxi IRC history that there are some patches for HDMI audio for H3 H6 H64. What about A20 ? Is there any patches available?

Hi team! This may be the stupidest question ever… I am a long time Debian user. I have a project in mind where I plan to setup a dual node HA Haproxy balancer. This is pretty straightforward in Debian but I am wondering, is HAproxy even available for armbian?. I do not plan to have a big throughput for these HAproxy nodes, is for a homelab and more for fun than for production purposes… The idea is to use the cheapest dual gigabit board available, that’s why I will probably go for nanopi (which supports armbian). English is not my first language so sorry in advance for messed up wording/expressions/whatever. …

Hi. I would pre-configure a board in a SBC small lan. The board is blind and I have not the cable to config it from outside, i have to config it by txt file to get it online in the lan at the startup. Firt of all I have to write the ip plan of the SBC LAN. I configured one of them (the first) in the lan by a text file called "interfaces" stored in the etc/network. The file contains there few rows: source /etc/network/interfaces.d/* # Network is managed by Network manager auto lo iface lo inet loopback # Rete Lan auto eth0 iface eth0 inet static address 192.168.1.11 netmask 255.255.255.0 network 192.168.1.0 gateway 192.168.1.10 # Scheda primaria Wi-fi…

Hello, I'll like to build my own kernel, mostly to learn more about Linux on ARM. The device I have is RK3399 based (Nanopi M4v2). Can I use the mainline kernel or are some parches needed? Where can I get the correct DTS? Is there any guide on how to do this? I'm not unfamiliar on how to build a custom kernel, but that was on x86/x64. ARM is a very different animal.

Hi there, I am just starting with Armbian, installed on odroid c2 emmc card, all seems to work, but when I tried to install software via armbian-config/softy just when I hit that I got on the screen small error: /etc/resolvconf/update.d/libc: Warning: /etc/resolv.conf is not a symbolic link to /etc/resolvconf/run/resolv.conf It is disappearing after 2-3 sec and I can install software which works (at least omv which I wanted) but it is weird to me.

This is a minor issue, but I'm hoping to get it solved as I've enjoyed the welcome screen for so long. For whatever reason after running my installation script which I've been using for years, the welcome screen changes when logging in over ssh. This happened some months ago. Any ideas on how or where I should look? Spoiler FROM: ___ _ _ _ _ _ ____ / _ \ __| |_ __ ___ (_) __| | | \ | |___ \ | | | |/ _` | '__/ _ \| |/ _` | | \| | __) | | |_| | (_| | | | (_) | | (_| | | |\ |/ __/ \___/ \__,_|_| \___/|_|\__,_| |_| \_|_____| Welcome to Armbi…

Hello, I have been using armbian for a couple of months now developing a small product, and this is my issue... When the OS boots, it gets directly to the Desktop environmet and never asks for a password (unless for a supervisor function form the terminal) I need one of the following options... 1) OS ask for password before let yo do anything on the desktop 2) It boots onto a console and ask for password (then you can manually start the Desktop) Any Help will be apreciated..! Best Regards

Hi, I'm trying to use commands v4l2-ctl --list-ctrls and v4l2-ctl --list-ctrls-menus on an Armbian PineCube. These commands work out of the box on NixOS, what preparation is necessary on Armbian?

I have a newly-installed Armbian_5.25_Orangepizero_Ubuntu_xenial_default_3.4.113 image. I find that I am unable to successfully upgrade the image. Note that operations like 'apt install hostapd' complete without problems. A transcript of my attempts follows. upgrade.log

see title, can help setup letsencrypt cron if needed

I have been working on orange pi zero h2 daily for about a year to make a pretty good distribution but now I want to produce my console but the board only comes with headers and usb/Ethernet all soldered on making it fat, any one have a connection to the manufacturer to not make it with pins or usb/Ethernet soldered on. This is what I want my orange pi zero h2 to look like: https://www.friendlyarm.com/index.php?route=product/product&path=69&product_id=212 I have had bad experiences with the h3, only h2 is good for me.

Hello, It seems a few weeks ago linux-headers-3.4.113-sun8i package was removed from armbian repo. Is it persistent? How I can get it? Thank you. -- BR Oleg

Hi , I've got a python script talking to one of the serial port via pyserial. It works fine when I execute using the terminal. If I place it under startup, the behaviour is changed. It doesn't work properly compared former. Has anyone come across this problem. Advise/help is appreciated.

The usual way to get the a headless linux box up and running is to flash a disk image to a µSD card and then insert that card into the linux box, boot, answer some questions and it's done. Can I not do the same thing with an image file that I put on the µSD card (in addition to the µSD card having a complete linux OS that the box can boot from) and copy that to the emmc? Then pull the card and boot from the emmc? Does the image file used for a µSD card differ from the image file that should be written to the emmc? e.g. I have an armbian image, say "Armbian_25.2.2_Rockpi-s_bookworm_current_6.12.15_minimal.img.xz", on my µSD card at /media/…

I have a orange pi plus 2e The time was ok a few days ago but now it is off by - 12 hrs +53 minutes which is before gmt thanks for your help Dave Do I need to open a port in the router?

Hi, i have make a Update of kernel 4.19.x, but After the Reboot the Cubitruck doesn‘t start. I only See the Message of the Screenshots attached. What can i do To run the System again? Thank you Gesendet von iPhone mit Tapatalk

HI, I success use follow UDEV rules for mount usb dev. But have problem, this can mount only one usb dev in directory /media/usb How make a multiple mounts like: /media/usb/dev1 /media/usb/dev2 etc... ACTION=="add", KERNEL=="sd*", SYMLINK+="usbdisk%n" ACTION=="add", KERNEL=="sd*", RUN+="/bin/mount /dev/%k /media/usb", OWNER="root" KERNEL=="sd[a-d][0-9]", OWNER="root" ACTION=="remove", KERNEL=="sd*", RUN+="/bin/umount /media/usb"

Good day. Yesterday I downloaded the latest Armbian version for the ASUS Tinker Board S and flashed the built-in eMMC (with Etcher Balena). The software works fine, but - the SD card is not mounted as mass storage, the file manager THUNAR does not recognize it. also lsusb does not recognize it. - a plugged USB- flash-stick is not mounted by the file manager THUNAR, although lsusb lists it. Ist das Problem behebbar? Is the problem fixable? The USB stick of a wireless mouse is recognized and also connects to the conputermouse. Regards Karl Translated with www.DeepL.com/Translator (free version) …

I am running rsyncon my rockpi nas pulling from another nas and the performance initially pretty good at around 90MB/s and after a while, it degrades to 39Mbs with high io/wait times - any ideas/suggestions are welcome. Here are the outputs of amrbianmonitor -U Time big.LITTLE load %cpu %sys %usr %nice %io %irq CPU C.St. 15:33:55: 600/1416MHz 0.85 4% 1% 0% 0% 1% 0% 41.7°C 0/6 15:34:00: 600/1008MHz 0.78 1% 0% 0% 0% 0% 0% 41.1°C 0/6 15:34:05: 816/1200MHz 0.72 1% 0% 0% 0% 0% 0% 41.7°C 0/6 15:34:10: 1800/1200MHz 0.66 10% 5% 4% 0% 0% 0% 46.9°C 0/6 15:34:16: 2016/1512MHz 0.85 39% 2…

I need to use VideoLAN VLC on my Pine64, with Armbian Buster. When I play an H264 mkv video, I got images too slow, and then it stops (like freeze). I think there is no hardware acceleration. When I start with mpv through the command: export VDPAU_DRIVER=sunxi mpv --vo=vpdau --hwdec=vdpau --hwdec-codecs=all filename.mp4 I got this: Playing: test.mkv (+) Video --vid=1 (*) (f) 'TST' (h264 1920x1080 23.976fps) (+) Audio --aid=1 --alang=eng (*) (f) 'ENG EAC-3 6ch @640kb/s' (eac3 6ch 48000Hz) (+) Subs --sid=1 --slang=eng (*) (f) 'ENG FORCED' (subrip) Subs --sid=2 --slang=eng 'ENG FULL' (subrip) File tags: Title: test [vo/vdpau] Error when…

I have spent the greater part of the day trying to get fbtft working on an ili9341 display on the nano pi neo with the legacy kernel. I have looked through the forum over and over and I cannot find out how the pins are numbered for fbtft. I got https://github.com/wertyzp/WiringNPand did a gpio readall and that gives me some pin numberings. I have tried both the pins from wPi and BCM. Neither work. I have done this many times on a raspberry pi, but cannot seem to get it to work on any of the H3 stuff. I saw in the forums that in the mainline kernel, there is a mathematical equation for pin numberings. I tried that as well, with no luck. I also tried giving the actual portp…

Hi, I recently bought an Odroid HC1 and installed Debian 8 on it. I am being quite happy so far with the installation, however this softy installer is very frustrating. I tried to install Syncthing, which failed to start, then now Webmin, hoping to be of "smaller scale", but no lack. It repeatedly fails to do something, displaying the errors behind the curses window, so I had to stop it with Ctrl-C. Then I got back to the menu and after quit, a cleared screen. Brilliant. Are there logs stored somewhere, at least? I checked /var/log/, but got no further. Or how I am supposed to go through failing installations? Thank you,

Hello, My spare R4S is currently running the Rolling releases with Armbian Linux v6.12 Trixie image It seems /etc/resolved.conf got filled by at least /etc/systemd/resolved.conf [ global ] /etc/netplan/armbian.yaml [ per link/ ethernets: ] However I miss from which script the IPv6 nameservers are gathered and added as currently /etc/resolv.conf shows something like this and Iike to have just the ones from [ global ]: ( Please note I removed nameservers from the yaml file already ) # operation for /etc/resolv.conf. nameserver 127.0.0.1 nameserver ::1 nameserver fda8:5894:4e78:0:xxxx:xxxx:xxxx:xxxx # Too …

Hi, file names with Asian characters are displayed as "?????" in Armbian. $ sudo mount.cifs //192.168.0.200/y /media/200_y -o user=armuser $ ls -1 /media/200_y/ "??????_text.txt" "banner_????.jpg" $ cat /etc/default/locale # File generated by update-locale LC_MESSAGES=en_US.UTF-8 ##LANG=en_US.UTF-8 LANGUAGE=en_US.UTF-8 ###LC_ALL=en_US.UTF-8 LC_ALL= LANG=en_US.UTF-8 LC_COLLATE=ko_KR.UTF-8 ## For your Information, in my ubuntu, there's no such a problem. It displays the above file names with proper Asian characters. Thank you in advance for any hint!!

I use "Armbian_5.59_Tinkerboard_Debian_stretch_next_4.14.67". After every reboot the line for the nameserver in resolv.conf looks like this: ^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@nameserver 192.168.3.1 When I delete all ^@ chars my networks works fine. After reboot the characters are inserted again. I tried "chmod 444 resolv.conf" but after reboot resolv.conf has 644 again. How can I correct this? What is the problem with my installation? Best regards.

I am new to armbian, and so far I managed to build a working image with some custom packages added and some removed by customizing `userpatches/lib.config`. Easy stuff and it's working great so far! Now I need to build some packages from sources and get them added to the resulting image. The usual way I would do this, would be installing a cross toolchain, having a staging dir with includes and libs from the dev packages I add to the image, etc. But after building the base armbian image, on my system I see I have two docker images related to armbian (ghcr.io/armbian/docker-armbian-build and armbian.local.only/armbian-build), and I wonder if maybe the "local on…

Good afternoon, I have just started studying the use of embedded arm linux for single-board computers. I'm asking for help from experienced developers. I have an orange pi lite. I uploaded a prebuild minimal armbian image to the microsd card: Armbian_community_25.5.0-trunk.444_Orangepilite_bookworm_current_6.12.23_minimal.img.xz .After that, I installed mate desktop environment according to these instructions: https://forum.armbian.com/topic/28786-install-mate-desktop-to-minimal-image-blues/. The problem is that the processor heats up very much under load (I registered a temperature of 95 degrees celsius using armbianmonitor) and periodically turns off due to overheating.…

Hello, I have installed the Armbian image for Rock Pi S (https://www.armbian.com/rockpi-s/) released 19th of October 2022 on my Rock Pi S and it boots fine. However, if I update the linux kernel (using apt-get install linux-dtb-edge-rockchip64 linux-image-edge-rockchip64) this breaks the image and it will be stuck on starting kernel the next time I reboot. These packages are not installed automatically, but are listed as kept back. However, since they break the system they should maybe not be possible to install.

Hi i'm using the "Win32DiskImager" to backup my sd card(8GB), file size almost 8GB after read from sd card. my question is, how to backup sd cad into image file and get small file size also. like downloaded form " armbian" web . Board: Orange Pi Zero

Out of the blue without any manual changes Orange PI PC Startup script screen stopped showing today. Is there anyone who knows how to fix that ? or what might have happened ? Thanks Björn

Hi, As I have quite unpopular mobo, I am playing with armbian alone with sbc like in topic I am on macos, I created a docker container with ubuntu, I cloned armbian project there and I was able to run ./compile.sh I had some errors but I was able to fix them but now I really stuck after some options selection (depending which way I choose) I am always ending in same place: [ .... ] Extension being added [ sunxi-tools :: added by main.sh:381 -> configuration.sh:178 -> config/sources/families/sun7i.conf:1 -> config/sources/families/include/sunxi_common.inc:1 ] [ o.k. ] Extension manager [ processed 3 Extension Methods calls and …

I can run device with compatible dtb(but has bug),so I write for myself. But the dtb that I compile can't start. So I want to compile dtb quick and debug. I only know `compile.sh` to build complete img but to slow, How to only compile dtb?(like `make ARCH=arm64 dtbs`)

Hi I would like to install the following module: mt7601u Unfortunatly i need kernel-hearders at least for this , i think My hardware is an Orange Pi Zero HC2+ My system realease is as follow PRETTY_NAME="Armbian 21.05.2 Buster" NAME="Debian GNU/Linux" VERSION_ID="10" VERSION="10 (buster)" VERSION_CODENAME=buster ID=debian HOME_URL="https://www.debian.org/" SUPPORT_URL="https://www.debian.org/support" BUG_REPORT_URL="https://bugs.debian.org/" Any idea ?

There is nothing about version information on the NVIDIA Jetson Nano page, and the image is from A02. Can this image also be used with B01?

I was initially overjoyed to find these loads for the Macchiatobin, as they allowed me to install a boatload of software including drivers for a PCIe device. Unfortunately. it appears that the U-Boot version (21.01) does not enumerate the PCIe bus correctly. As a result, I can't test that PCIe device. The relevant failure is: PCIE-0: Link up (Gen2-x2, Bus0) PCI: Failed autoconfig bar 10 PCI: Failed autoconfig bar 14 PCI: Failed autoconfig bar 10 PCI: Failed autoconfig bar 14 pci command output is: => pci 0 Scanning PCI devices on bus 0 BusDevFun VendorId DeviceId Device Class Sub-Class _____…

i am trying to install the MFC-L2710DW printer on the pc in question, but it is not recognized by the cups database. I also tried to install the printer-driver-brlaser package (where there is the driver for the mfc-l2710dw), but it's as if it wasn't installed. how should I do the cups setting. the s.o. it is armbian buster xfce. the printer is connected with both USB and wifi

I have an orangepi pc+ which (among other duties) exports my usb (/media/wd/Music) drive with nfs. The external usb drive (A Western Digital) automatically enters sleep mode when it is not used for a while. When I try to mount that nfs-share on another machine, I hear the drive spinning up (awakening) and the mount succeeds. But when I try to access the mount I get "ls: cannot access /opt/music: Stale file handle" I had the same drive and /etc/exports on my raspberrypi-2 but there I did not have this problem (I could hear it spinning up as well when I accessed the mount so I know it was entering sleep mode as well). So I think it is a difference in configuration…

Hello, i am very new to using armbain. I picked up an orange pi lite and loaded armbain debain jessie using etcher on a 16gb card. when i install it to the orange pi lite and power it on it asks me for a user name and password. i did as instructed using rot and 1234. then i added my name and made a new password as instructed. it then acts like its booting and says orange pi lite on the screen but wont boot the GUI desktop as it describes. it displays the name and some of the current states of the board (temp ect) but then sits at a command prompt waiting for input. i can type help and it will give me a list of commands that work for it but none indicate they will boot the…

Both focal and bulleye can startup on cubieboard1 but without network. screen log shows: sun4i-emac 1c0b000.ethernet eth0: could not find the PHY sun4i-emac 1c0b000.ethernet eth0: cannot probe MDIO bus ifconfig show only "lo" and no "eth0" The network on USB-ethernet adapter is working. And I'm sure the onboard eth hardware is OK, because it works on the old system (wheezy and jessie) . Is it a driver issue? Any help is appreciated. Thanks!

Armbianmonitor: http://ix.io/3zoC I am using a NanoPi R1S-H3 that runs on the Allwinner-H3 CPU: https://www.friendlyarm.com/index.php?route=product/product&product_id=274. I flashed a copy of Armbian 21.08.1, Buster current 5.10.60 for the NanoPi R1, which has a similar H3 chip. The R1S-H3 has an onboard SDIO Wi-Fi card that requires the RTL8189ES drivers, which I have loaded in already. Unfortunately, I am unable to use the Wi-Fi card on the device. I did notice an error: "mmc2: error -22 while initializing SDIO card" which might be the cause. However, I am not too sure on how to go about resolving it. Any suggestions? Thanks in advanc…

Hi everyone, I have to make a custom kernel for a RK3568 based device with kernel 4.19.232. Currently running Ubuntu 20.04LTS. I followed this guide https://opensource.rock-chips.com/wiki_Rockchip_Kernel and I tried compiling 4.19 from rockchip source code and made a boot.img with the rk3568-evb1-ddr4-v10.dtb. The device boots but HDMI isn't working correctly, LVDS appears detected but does not show anything and one USB stopped working. Since I am new to all these things, does anyone know of any guides to compile kernels for rockchip ? I am trying to replace the boot.img from the original FW because kernel is inaccessible and iptables is not wor…

Since some H2 and H3's run hotter than some people would like, and people are measuring voltages etc I thought I'd make the following warnings for your benefit in the hope that we collect quality data and solve all challenges quickly. Measuring voltage accurately Your DMM (digital multimeter) may lie to you. Measure the input voltage as well as the test voltages before posting voltage readings. Check with the resistance setting that the resistance of your probes touching each other is close to 0 ohms. I own many DMM's and one of them reports horribly inaccurate voltages when the 9v battery is near or less than 8v. If your DMM sucks, buy a better one (link at botto…

Hi, I am using Bluetooth and WiFi in the same time. Bluetooth is using for a whole time and WiFi 1 time per minute. So, I don't need WiFi connection very fast and do need most of network services. Due usage of AP6210 module, WiFi and BT shares the same communication channel (UART). I continuously send data (1Mbps) via Bluetooth. WiFi is used by my app 1 time per minute.The problem is that Bluetooth drops communication for about second. Reducing BT speed does not help. I noticed that when I download file from OPI board,that drops occurs much often. It seems that WiFi has a higher priority than BT in communication. Strange thing is that when I don't use WiFi network, i…

Hi, I need to install kernel headers to build a wifi driver. Using armbian-config to install the headers does not work ... After much searching came across a logical suggestion - i.e. install the 'linux-headers-current-sunxi' package ... When I install that package (on a fresh 22.08.1install), the package installed is for 22.05.03 ... which is, er, the wrong version? Where do I find the headers for 22.08.1 ? Many thanks!

This is the method of cloning I have been using for several years. Saved me lots of time. Applications: YUMI, QT5-fsarchiver, Wine, Live OS, and Sandisk USB. 1 Make a bootable-usb using YUMI. Install a live OS. I prefer PClinux Live on a sandisk USB 128/256gb or Solid-State drive. Bootup the USB and install QT5-fsarchiver using synaptic. 2 Or install QT5-fsarchiver in any PC/Laptop. 3 Plug in the Tinkerboard, or what ever, to a USB port and create a full backup image of the MMC or SD card. 4 Save the image file anywhere. 5 Restore the image using QT-fsarchiver to any memory device. Note: In the PClinux live insta…

Hello, I need to install linux-headers, but the old version is in the repository. Where can I find the current version(5.99)?

After a long time not using my cubietruck i decided to install the new Armbian Buster to it. I installed the xfce gui and now the gui is very very slow. If i move a window it tooks about 1-3 seconds till i see its moved. Complete gui is very juddery. The Task manager in debian buster shows the cpu and memory is not always on 100% although xfce is very slow. How can i fix this? Can it be cause i use a few years old 64gb samsung micro sd? If it's because the cubietruck is too old and slow can you recommend another newer much faster system?

Hi guys, I am trying to make autostart of my app, but the app is launched by bash script that automatically launch the app again when crashed: (it finds the latest application version and then launch...then it is waiting for crash , rerun and wait again) - when I placed this script in /etc/profile.d, my system got stuck on my application view without loading desktop (and other needed services). #!/bin/bash sleep 30 while true do str=`ls /home/lufa/Shared/QT/xxxx* | sort -n -t _ -k 2 | tail -n1` if [ ! `pgrep $str` ] ; then $str fi sleep 30 done Thus, I added autostart.sh.desktop file in ~/.config/autostart/ like this: [Desktop Entry] Type=Application …

Hello, This may seem simple for you, and I feel stupid for asking, but I'm not sure how to install the driver provided by KeeTouch, the touch screen provider, on my OrangePi One. This is the driver provided, but there is no instruction on how to install it. https://keetouch.eu/files/drivers/saw/linux/linuxupdd4.1.11.tgz The screen is a keetouch kot-170c-us-sa4bcw accoustic wave touch screen, connected by USB for the touch screen and HDMI to DVI to the OrangePi. The OrangePi One (H3) is on Armbian 22.05 Jammy XFCE and has nothing installed yet, the touch screen is first order of buisness. I have searched for a whil…

Hello! How to fix hdmi overscan for retarded tv, is it possible? H3 OPi + Armbian Stretch Desktop last night's Nightly I tried setting overscan_x/y in armbianenv.txt and u-boot and a display-mode line including them, didn't work. Does it need extra settings, like disabling edid or some order of settings?

root@orangepizero:~# apt update Get:1 http://security.debian.org stretch/updates InRelease [94.3 kB] Get:2 http://security.debian.org stretch/updates/main armhf Packages [470 kB] Get:3 http://security.debian.org stretch/updates/contrib armhf Packages [1,764 B ] Get:4 https://apt.armbian.com stretch InRelease [19.0 kB] Get:7 https://apt.armbian.com stretch/main armhf Packages [334 kB] Get:9 https://apt.armbian.com stretch/stretch-utils armhf Packages [6,376 B] Get:10 https://apt.armbian.com stretch/stretch-desktop armhf Packages [2,211 B] Ign:5 http://cdn-fastly.deb.debian.org/debian str…

Hi, My ODROID-HC2 has just arrived and I flashed a SDCard with a fresh Armbian Sketcher fot it. Did the initial configuration, with apt-upgrade and then opened Armbian-config and selected to install OpenmediaVault (the only other things installed are SAMBA and Softether). The installation started whiteout any problem, but I got some errors the it tried to install openmediavault extras package. Since all logs were vanished after the install stopped, I cannot post here. But when I try to install again, I get this errors: If I try to do an apt Upgrade I receive the following error: alexantao@NAS:~$ sudo apt up…

How/where do i set how active screen appears? it covers(out of screen) task bar. it doesn't have minimize full or exit option. Can't drag. Alt +f4 doesn't work.

Good evening, Is it possible to "re-use" the system on SATA ? And how would I do that. I use a HC4 with SD card, a SSD and a HDD I flashed the SD card with Armbian_20.11.1_Odroidhc4_buster_current_5.9.12.img.xz then used armbian-config to Boot from SD - system on SATA. (sdb2) also I installed PiHole, OMV ... Due to an power failure the HC4 was not booting anymore. With a newly flashed SD card its booting again, but of course its not using the system on sdb2 When using armbian-config it would erase by sdb2 before Could I somehow use the system which still should be on sdb2 instead of starting from beginn…

Hi, when running armbian-config i noticed OMV(openmediavault) not found in list software, this is my armbianmonitor -u http://ix.io/1l0

Hi can anyone help. I've got CSF firewall running on my Helios4 and I keep getting emails saying that rsyslog isn't running. I checked the logs and it seems stuck at this error: liblogging-stdlog[10738]: action 'action 11' suspended, next retry is Sun Mar 11 15:36:43 2018 [v8.24.0 try http://www.rsyslog.com/e/2007 ] Is there any fix for this? Thanks for any help

Hi, I am new at this platform. I want to know is there any difference between BIOS and manual overclocking? Can anyone give me a detail answer?

Hi all, I'm trying to port a driver built for Raspberry Zero to Banana Pi M2 Zero. The original driver is here : https://github.com/pguyot/tagtagtag-ears (it's supposed to drive the ears of a Nabaztag, which recently got resurected thanks to an Ulule campaign). My understanding is that at least half of the problem is to adapt the device tree overlay for the BPI M2 Zero. If it"s not half of the work, it's definitely required. So far I've been unsuccessful. The original DTS overlay is like this : /dts-v1/; /plugin/; / { compatible = "brcm,bcm2708"; fragment@0 { target = <&gpio>; __overlay__ { gpio_encoder_left_…

Hi all I am new to V3s dev. I am creating a small computer based on the lichee pi zero. I am trying to get the best option to add a keyboard. Would you suggest me to design an I2C keyboard , or will a classicac usb keyboard work out of the box ? Building a usb keyboard based on an atmega32u4 microcontroler would be very simple.

I realize the A10-OlinuXino-Lime has been EOL for Armbian for some time now; however, I am curious if kernel support for GPIO functionality is available on the latest available for Armbian Xenial (kernel 3.4). If it is a mainline kernel this may explain why the GPIOs are not available for use.

Good morning, I'm new to the community and I'm having problems with wifi adapters driver. I tested some changes that were not recognized. Now I'm testing a RTL8088CU, it came to be recognized at first, but after typing the wifi password it restarted itself and when the call back goes into conflict with the bluetooth dongle and back off. I'm interpreting this as a driver problem, where can I find the usb wifi driver and do its installation? Thank you

I installed a LinuxCNC for my orange pi one, the mouse and keyboard will not work after restarting Here is the log http://ix.io/2AgR

Hi all, I am trying to have a script running when eth0 i s up, but it seems that I don't get it. Although I followed a guide and set anything, NM is not triggering my script. So I have created my script without sh extension and called it 90-start-script in /etc/NetworkManager/dispatcher.d: logger -s "I DON'T SEE THIS" if [ "$1" == "eth0" ]; then case "$2" in up) ~/scripts/start_check.sh ;; esac fi; I gave it root ownership, execution flag, but it seems to be not working... I followed this guide: https://wiki.archlinux.org/index.php/NetworkManager#Network_services_with_NetworkManag…

Hello, I have the Odroid XU4 since january, but a proper installation of Yunohost is impossible... I tried to install Debian Server, but I encounter an error in the reposites.

Hello! How can I schedule power off the board? After power on, I want to turn off the device automatically 7 hours later. At the moment, time switches turn off the boards power supply in every day... dead 3 SD cards...

Installed Armbian to SD-card-1. Booted Cubietruck from it: works great. Made some changes in system and wanted that changes to another SD card, so I copied entire root ( / ) filesystem from SD-card-1 to my-armbian.tar.gz. There is better ways of doing this: dd or another make-image-software or better remember my changes related to original Armbian and made that changes in new system. But lets consider my stupid way:) Got new SD card: SD-card-2. Created partition table with 1 partition. Made ext4fs on that 1 partition. Unpacked my the filesystem to the partition. Used gparted and set flag BOOT. SD-card-2 didnt booted. I realized that i need U-Boot on it. …

I use the serial library but when I import it. it will show an error. why? File "test.py", line 1 SyntaxError: Non-ASCII character '\xe2' in file test.py on line 1, but no encoding declared; see http://www.python.org/peps/pep-0263.html for details when i change coding, with the following code, it has the error again # coding: utf-8 how can i solve it??

Hi everybody, My question is about stop a running program with C. I have written a c code to start program with system() function in orange pi zero. I am starting RTKLIB software, which is STR2STR and when my code starts the software with command str2str -in serial://ttyS1:115200 -out serial:ttyS2:115200, I can stop it with CTRL^C but I want to stop it from my software. When I got a TCP pocket containing a exit status word. It should stop the STR2STR software. I am not very good at linux. How can I do that? Thanks

Would passive cooling be any good for OrangePi PC Plus? Or active cooling is better suited?

Hi All. Are there any rules to setting the CPU frequency and DRAM frequency using this tool? Eg: can you set the CPU Frequency to 827mHz (just a weird number) or are there specific multiples that are needed? Are there any combinations to avoid or that are best suited together? Thanks. J.

Hello, Ihave an Odroid N2 that run with armbian. 1) I can't upgrade armbian-zsh_21.08.6_all.deb The output of apt upgrade is : (Lecture de la base de données... 133099 fichiers et répertoires déjà installés.) Préparation du dépaquetage de .../armbian-zsh_21.08.6_all.deb ... Dépaquetage de armbian-zsh (21.08.6) sur (21.08.5) ... dpkg: erreur de traitement de l'archive /var/cache/apt/archives/armbian-zsh_21.08.6_all.deb (--unpack) : impossible d'ouvrir « /etc/oh-my-zsh/plugins/osx/README.md.dpkg-new »: Aucun fichier ou dossier de ce type Des erreurs ont été rencontrées pendant l'exécution : /var/cache/apt/archives/arm…

Hi, Appreciate any help on this :) Sorry if this is the wrong place for this. Problem: iiyama Prolite E2783QSU will not display resolution higher than 1080p on RockPro64, I'm sure it's supposed to go up to 4k Background: I've spent the last few days getting Armbian booting from NMVe which is all good and got Desktop up and running with MATE and over coming issues with brisk menu not working. I have other issues than this but will post separately for those. My Background: Last used Unix back in 1997, just 86ed Windows from my life, this is interesting but harder than I thought lol. Best Rich

Hello, I try to boot on an Orange PI Zero, after several attempts with armbian 5.25 jessie and xenial.Systematically the boot hangs (totally frozen). In the boot log I have the following error (at line 960 of the pastebin) "[FAILED] Failed to start Load Kernel Modules." Full booting log status: http://pastebin.com/tzyk2uMk Is there anyone to help me thank you

i want to use led on/off 7 pin (gpio 40 header) but it doesn’t work. Others work fine: echo 20 > /sys/class/gpio/export echo 23 > /sys/class/gpio/export echo 40 > /sys/class/gpio/export echo 42 > /sys/class/gpio/export echo out > /sys/class/gpio/gpio20/direction echo out > /sys/class/gpio/gpio23/direction echo out > /sys/class/gpio/gpio40/direction echo out > /sys/class/gpio/gpio42/direction echo 1 > /sys/class/gpio/gpio20/value echo 1 > /sys/class/gpio/gpio23/value echo 1 > /sys/class/gpio/gpio40/value echo 1 > /sys/class/gpio/gpio42/value May be problem in pwm10 pwm10 { …

A while back, I noticed that Armbian was compatible with this Ugreen GbE adapter. As I purchase on eBay rather than Amazon, I found the above one plus this adapter, which has the same AX88179 chipset plus a built-in 3-port USB3-Hub. So I decided to try it and see if it worked with Armbian and report back here. (I'm using the EspressoBIN for this and Ubuntu Bionic 4.19.56). These are my results: Straight out-of-the-box, I can see it using LSUSB, but it does not plug-and-play-work. After struggling and attempting to get the network manager to do something about it, I added this line to /etc/udev/rules.d/70-persistent-net.rules: SUBSY…

Đồng hồ treo tường Rhythm CMG749NR13 – Sắc anh đào quyến rũ Nhiều người có quan niệm rất sai lầm về đồng hồ treo tường, rằng đó là những chiếc đồng hồ có màu sắc cổ điển, với những con số truyền thống. Với đồng hồ treo tường Rhythm, những người quan tâm đến đồng hồ chắc chắn sẽ có cái nhìn khác về vật dụng thiết thực trong ngôi nhà của mình. Nổi tiếng là tinh hoa thời gian của xứ sở mặt trời mọc, đồng hồ treo tường Rhythm CMG749NR13 mang dáng vẻ bên ngoài vô cùng quyến rũ, đặc biệt có sức hấp dẫn với phái nữ dịu dàng, quý phái. Đồng hồ treo tường Rhythm CMG749NR13 mang sắc hồng đào quyến rũ Vượt ra ngoài những bảng màu đen trắng ha…

Hi everyone, i have uptabte armbian from 23.05 to 24.1 (stable relase update) in my nano pi neo air, but arter update i cant connect to device via com port from micro usb. (no avalible devices, when i connect nanopi to my PC) How i can fix it? Armbian-config? P.S. I also soldering external usb-uart and to the nano and i see that update was sucsessful, device steel working.

i want instal peerflix on Armbian_5.41_Orangepiwin_Ubuntu_xenial_default_3.10.107_desktop, i've install first nodejs from synapsis and after install nodejs -v -> 4.2.6 i run npm -y install peerflix and if return the error message : peerflix --help /usr/local/lib/node_modules/peerflix/node_modules/parse-torrent/index.js:257 ;(function () { Buffer.alloc(0) })() ^ TypeError: Buffer.alloc is not a function at /usr/local/lib/node_modules/peerflix/node_modules/parse-torrent/index.js:257:24 at Object.<anonymous> (/usr/local/lib/node_modules/peerflix/node_modules/parse-torrent/index.js:257:35) at Module._compile…

Hi! I need to use PHP 5.3 that is requiriment of old version of vtigerCRM. How to install it in Armbian?

Can't seem to get logged in. Not used to cmd line and can't see first 10 characters. Would like to see a detailed line by line entry for changing the password. Yes I am that stupid.

Hi! I just flashed Armbian 24.11.1 Bookworm Minimal / IOT onto my Odroid HC1 SD-Card. The download page states: "For HC1 and HC2 we provide specially optimized config which has to be applied manually. This results in shorter boot time and lower consumption. Edit /boot/armbianEnv.txt and add: board_name=xu4 # or xu3, xu3, hc1" However there is no /boot/armbianEnv.txt. Should I just run the system as is or do I have to modify something to have it run optimally? Should I just create the file and add line? Thx! Björn

How use s_rsb0 as TWI ???

Hello. I have installed openvpn and network-manager. I select Openvpn. I go to create and select automatic. I input my .ovpn file and the save button is greyed. It asks for a PAC Url. But, my vpn provider doesn't use pac urls. Is there away I can get vpn working? Armbian working great. It's a very good operating system. Everything works only vpn is the last one to get working. Armbian running on a tinkerboard. armbianmonitor -U ta. 4517 [ 13.987953] systemd[1]: Started Set console font and keymap. 4518 [ 14.021762] nf_tables: (c) 2007-2009 Patrick McHardy <kaber@trash.net&g…

hi everyone, i have a board without serial output and i also don't know which os in it. The one thing i can do is that i can burn image by amlogic USB Burning Tool,But it seems that amlogic USB Burning Tool can't open and burn armbian image direct, it says that parse image file failure. How can i do if i wan't burn armbian in it,does have some tool change armbian image to USB Bruning Tool's format or some tool instead of USB Burning Tool

Not posting everything I've tried, just wanted to ask a question of people experienced with the H3. Does it really support slave I2S in the mainline kernel? I've seen it posted in multiple forums that it does, and the datasheet and user manual says it does, but I can not get it working. Has anyone seen this work in person? I had to hack up the sun4i-i2s.c driver around mclk / bclk generation to make it happy just to even try it, and confirmed that all register settings look good. But the DMA just doesn't seem to transfer data when in clock slave mode. It doesn't seem like any cpu using sun4i-i2s should work in clock slave mode.

Hello! I have problems to install OMV on an Odroid. Bullseye is installed and then I start the install script from github. The install script of OMV does not work - some mirrors are not https but only http. Anyone has an idea? The odroid is connected to an aDSL router. I raised this issue at github and got the response to ask here. See https://github.com/OpenMediaVault-Plugin-Developers/installScript/issues/88 Thanks for any help! Updating repos before installing... OK:1 http://packages.openmediavault.org/public shaitan InRelease OK:2 http://deb.debian.org/debian bullseye InRelease Holen:3 http://deb.debian.org/debian bullse…

Is it possible to use the nand-sata-install script non-interactively?