Beginners

I have a Orange PI PC that I"m setting up as my file server with samba. I am using a hard drive with a SATA to USB adapter for my storage device. I've read and tried many HOW-TOs and none of them seem to get it working properly. Even though, they all say it is easy and it looks easy. I am able to see the shared folder over the network but Windows says that I don't have permissions to access it. One idea that I've had is that I'm not accessing the share folder through the config file. However I'm not sure how to properly access my HDD. Right now I am using the path that you would get from opening the disk on the desktop. Something l…

Hello- I'm looking to marry free and open (as possible) software and hardware into one inexpensive system. I'm in over my head so apologies in advance if I'm asking silly stuff. I did check the basics on here and have been lurking. At any rate I've been messing around with the Lime 2 and haven't had much luck getting Parabola to boot into LXDE... or any GUI at all actually. I thought I'd try Armbian as the Debian Kernel has been blob-less for a while now. I really, really like it so far. I am using Mainline, just want to make sure I'm running all free software if possible. I have checked for non-free stuff via: dpkg-query -W -f='$…

hey guys how I can fix this error on armbian I just checked StackOverflow and many other sites but still the same any help? Thanks, Best Regards

Hello , I'm new to Armbian, I'm trying to create an SD image for an Olimex A13 Som card (https://www.olimex.com/Products/SOM/A13/A13-SOM-512/) + A13 Som WIfi (https: //www.olimex.com/Products/SOM/A13/A13-SOM-WIFI/open-source-hardware). After successfully executing the build and transferring the image to SD with Etcher, the boot starts correctly but hangs on Starting Kernel ... Do you have any idea how to solve the problem? Thanks in advance!

I'm trying to create a microSD card to boot Armbian, but first would be inserted into a Windows laptop to edit some configuration. To make the microSD show up in Windows, the first partition must be a FAT partition, and so Linux would be ext4 partion 2. I suspect I'll need to put the /boot partition on the FAT volume, with directions to load from mmcblk1p2. In case it matters, this is a Rock64 without emmc. I've just started this research, but I'd be grateful for any u-boot-savvy person's help here. Thanks.

Problem: as the title says, banana pi m1 is not responding to ssh after several days and need restart to be functional again. System does have a sata 3.5" 500gb samsung hdd attached. It is connected to the network by wired lan 100mb. Software running is lighthttpd (previous apache) and php. usage: a raspberry pi camera send pictures to http server multiple times per day with html post method, there is also a php/html gallery with the pictures for viewing All website/www and pictures folders are stored on sata hdd. There is also a cron job for erasing old pictures every 5 mins, quota now is set to 100GB. as ls ta…

I have a question. Because there is a big mess in the naming of the first Orangepi series. I have a board with orangepi mini 2 image working. Archived Armbian 5.05 kernel 3.4.119. Orangepi pi 2 images do not launch. In appearance and specifications, the Orangepi PC 2 and mini 2 are almost identical. https://linux-sunxi.org/Xunlong_Orange_Pi_Mini_2. However, the specification for the mini 2 exists, although the manufacturer himself does not provide it on its main website. Could you add an introduction to the orange pi mini 2 board, with the old 3.4 kernel, so that you can build a system? Or maybe someone has some archival image to share?

Hey. I'm working on setting up octoprint on my opi zero +2(H5), aiming at running octodash on a small 3.5" spi waveshare clone display. So far I've got the display working fine, as in showing the console text, and also working in xorg. However, I have a bit of trouble with the touch part. I've combed through the forum and followed the guides I could find, and have a fairly good working DTS file, however, I can't seem to get pin number 11 to work. In the overlay files, it seems to be named PA1, but I couldn't get that to work, and there were a bit of oddities with what pins seemed to be enabled, in relation to the various overlays. Howe…

Hello. I've tried a kernel I build using the tool orange pi provides, that kernel boots with a good HDMI resolution. However, when I use the default kernel that comes with my fresh armbian installation, I can't get the HDMI resolution to 480p. I set the resolution in boot parameters. I'd appreciate any help.

I am trying to run AWS Greengrass IOT software on an Armbian based Rockpi (latest versions). At its simplest it runs ok using AWs corretto or Java 8. I am running into issue when i try load up a lamda to set up tunnels. I get the following errors from the log file. The issue seems to start because Resource controller is not enabled. Reading further and taking a stab in the dark - this could be referring to the following cgroup_enable=memory cgroup_memory=1 - apparently usually found in a cmdline.txt in the boot folder. Can anyone in the community help ? [INFO] (pool-2-thread-7) com.aws.greengrass.util.platforms.unix.linux.LinuxSystemResourceController: R…

How should I use uart to view the system boot log? The kernel failed to boot and I would like to see the error log.

After trying different distro for the BPI M2 Zero, I installed Armbian, and it works great with a standard 16:9 screen. Now I would like to use a bar LCD (Waveshare 7.9 inches); but the setup instructions are for RPI, not for Armbian, so I am not sure how you set up a screen that is not default (And I exclude that I can just plug in the screen and it will magically work. I am not using X interface since the BPI is quite slow, so I am in terminal. Thanks

I'm trying to get the armbian x86-64 generic image to run in virtualbox. I can successfully convert the *.img file to qcow2 and qemu will run it just fine. However, virtualbox fails to boot it in any format (qcow2, vmdk, vhd, vdi, etc). The grub menu comes up, but when trying to boot Linux then it just sits at a blinking cursor. I've tried converting this a variety of ways, such as using `qemu-img convert`, `vboxmanage convertfromraw` and `vboxmanage convertdd`. None of them yield an image that virtualbox will boot. Has anybody else had success with this, and/or know how to fix it? Thanks.

Is there any description how to setup the boot logo? I tried what I found: in build/packages/blobs/splash change logo.png and run command line with "BOOT_LOGO=yes", it doesn't work. After I found "What we use now is plymouth". OK. Does it work in compile time? I don't have plymouth after installing armbian in a docker container. How should I use plymouth (if it is the only way) to make a boot logo in compile time?

I have spent the greater part of the day trying to get fbtft working on an ili9341 display on the nano pi neo with the legacy kernel. I have looked through the forum over and over and I cannot find out how the pins are numbered for fbtft. I got https://github.com/wertyzp/WiringNPand did a gpio readall and that gives me some pin numberings. I have tried both the pins from wPi and BCM. Neither work. I have done this many times on a raspberry pi, but cannot seem to get it to work on any of the H3 stuff. I saw in the forums that in the mainline kernel, there is a mathematical equation for pin numberings. I tried that as well, with no luck. I also tried giving the actual portp…

Hello, is it possible to use GPIO Pins with this OS? I would like to use this code: http://mujweb.cz/tlc/RasPi-SMT/ Board: OrangePI PC I decided to use this OS as the original images doesnt seem to support an USB WLAN adapter with atheros chipset I am using. This OS seems to work well with it.

Hi, does anyone have experience of using this: https://ru.aliexpress.com/item/Raspberry-pi-2-HIFI-DAC-I2S-Interface-Special-HIFI-DAC-Audio-Sound-Card-Modulecompatible-raspberry-pi/32652350376.html device on Orange Pi PC Plus I have modifyed script.bin file: [twi1] twi_used = 0 and [pcm0] daudio_used = 1 Then i saw in pulse audio new device, called "sndaudio" aplay say this: root@orangepipcplus:~# aplay -l **** Список PLAYBACK устройств **** карта 0: audiocodec [audiocodec], устройство 0: SUNXI-CODEC sndcodec-0 [] Подустройства: 1/1 Подустройство №0: subdevice #0 карта 1: snddaudio [s…

...as title. I've installed ispConfig using Armbian-Config, but now I want to remove it. How to do it? Googling I've see that there is a unistall.php or /root/ispconfig/uninstall script that do that, but there is no trace in armbian.

I have installed Armbian minimal on RockPi 4, but it can't recognise the armbian-config command: armbian-config: command not found login as: pi pi@192.168.0.234's password: ____ _ ____ _ _ _ ____ | _ \ ___ ___| | _| _ \(_) | || | | __ ) | |_) / _ \ / __| |/ / |_) | |_____| || |_| _ \ | _ < (_) | (__| <| __/| |_____|__ _| |_) | |_| \_\___/ \___|_|\_\_| |_| |_| |____/ Welcome to Debian Buster with Armbian Linux 4.4.192-rockchip64 System load: 0.35 0.09 0.03 Up time: 0 min Memory usage: 7 % of 985MB IP: 192.168.0.234 CPU temp: 57°C Usage of /: …

Hi I am not very experienced with armbian/linux. I have a raspberry pi that is connected to a 4K tv via HDMI. When I turn the tv off and on screen resolution changes to 4K. I need to fix it to 1080p. I searched but couldn't find something I can understand. How can I do this?

Hello, Please help with this issue: No Сapture selection in alsamixer or amixer. root@cubieboard2:~# arecord -l **** List of CAPTURE Hardware Devices **** card 1: sun4icodec [sun4i-codec], device 0: CDC PCM Codec-0 [CDC PCM Codec-0] Subdevices:1/1 Subdevice #0: subdevice #0 root@cubieboard2:~# amixer -c 1 sget 'Line Boost' Capabilities: volume volume-joined Playback channels: Mono Capture channels: Mono Limits: 0 - 7 Mono: 7 [100%] [9.00dB] root@cubieboard2:~# amixer -c 1 sset 'Line Boost' cap amixer: Invalid command! root@cubieboard2:~# …

Hello all, I am unsuccessful in setting up FDE (Full-Disk-Encryption) on an ODROID HC-2. This device has no display output and I have no clue if and how it's possible to debug the boot issue. The boot is done through the micro-SD card and I can mount the micro-SD card successfully on any other host for insight. Is there any known trick how to see what fails during the boot process? How can I do this?

Hello. I installed armbian (22.05 jammy) on my banana pi m1 (original model). Since it doesn't come with onboard wifi, I decided to attach wifi dongle which uses RTL8188EUS chip. However, although i see it is recognized as "realtek ~~ RTL8188EUS network adapter" when i type 'lsusb' command, it doesn't show up as 'wlan0' when i enter 'ifconfig -a' command. What can I do to make the module work again?

Ok so I’m using a orange pi 3lts and when I try connecting to a Wi-Fi network it fails so to find the problem I ran armbianmonitor -u and it said network/firewall problem detected not able to upload debug info and I tried to use armbian config to fix this but it didn’t work how do if fix this?

I've got an original Tinker Board rev 1.2 that I want to install Klipper on for a 3d printer. I've tried installing both Armbian 24.11.1 Bookworm Minimal / IOT and Armbian 24.11.1 Noble XFCE and with either one when I try to shut it down with "sudo shutdown now" or using the shutdown option in the desktop mode, the board seems to shut down, the lights go out but it still draws around 700mA and the CPU stays warm or even gets a little hotter (with the board powered on but doing nothing it draws around 460mA). I've tried disabling wake-on-lan but that didn't help. I've tried adding power_off to the extraargs line in /boot/armbianEnv.txt also didn't help. It d…

i have the Cubietruck and i want to burn to the nand the Vanilla jessie i did it before with lubuntu with phoenix suite and it was really easy i just dont understand how to do this with the raw file can someone please help ?

For my Orange Pi PC, I just switched from the buggy debian-image to Armbian. Armbian works fantastic, but there is one small problem with my ssh reverse tunnel. On the (old) debian system i had my script tunnel.sh: #!/bin/bash /usr/bin/autossh -p2000 -fNC -R 9000:localhost:9091 -R 5057:localhost:4949 -R 8000:localhost:8888 -R 10012:localhost:22 myusername@www.mydomain.com The remote Pi will call my gateway Pi at port 2000. Whenever i call the gateway-ip:9000 i am at port 9091 on my remote pi etc. Worked flawless. After I changed to Armbian, this mini-script for tunnel.sh works, too: #!/bin/bash /usr/bin/autossh -p2000 -fNC -R 10012:localhost:22 myusername@ww…

Hello to all. I'm trying to use the image Armbian_5.25_Orangepipcplus_Ubuntu_xenial_dev_4.9.4.img but I can not operate the webcam. With the image of the previous version, the webcam worked with gs2035 and vte_v42l modules, which can not find in the current image. Is it an omission or there are compatibility issues? Where could I find instructions (simple, if possible) to compile them? Thank you.

I recently took delivery of a Voltastream Zero, a just-released evaluation board which uses an i.MX6ULL processor. The support forum for that board isn't even up yet. Their main board image has neither the PPP kernel modules nor a C compiler, at least one of which I need in order to use the board for anything. How easy would it be to get a rudimentary Armbian image running on this board? I've had some luck with Armbian on my other boards and would like to see it on this one too. It doesn't have any video output or Ethernet, I just need the very basics.

?

Hi. I added a second wireless interface to my Rock64 and created a wifi hotspot using armbian-config. Now .local domains are not resolved anymore. I tried changing in files /etc/resolvconf/resolv.conf.d/base and /etc/resolvconf/resolv.conf.d/head IP from 8.8.8.8 to 127.0.0.1 but nothing changed. avahi-resolve-host-name is ok: christian@rock64:~$ avahi-resolve-host-name orangepi2mini.local orangepi2mini.local 192.168.0.12 but christian@rock64:~$ ping orangepi2mini.local ping: orangepi2mini.local: Name or service not known Could anyone point me on what could have gone wrong? Many thanks. Christian

Hi! help please - i by chance remove kernel module for w1 - can someone send it's to me... /lib/modules/4.14.84-sunxi/kernel/drivers/w1/masters/w1..... -- ARMBIAN 5.60 stable Ubuntu 18.04.1 LTS 4.14.84-sunxi orange pi zero H2+

Hi everyone, I've updated my pcDuino via: Sudo apt-get update Sudo apt-get upgrade I can reach 8.8.8.8 from the terminal and google.com from the Chromium browser. However, I cannot reach any other website. I am guessing it has to do with the latest TLS requirements. TLS 2.0 is required for 99% of global websites. I'm presuming my pcDuino is on an older version for TLS 1.0/1/1 Any thoughts or help is greatly appreciated Thanks

root@orangepizero:~# apt update Get:1 http://security.debian.org stretch/updates InRelease [94.3 kB] Get:2 http://security.debian.org stretch/updates/main armhf Packages [470 kB] Get:3 http://security.debian.org stretch/updates/contrib armhf Packages [1,764 B ] Get:4 https://apt.armbian.com stretch InRelease [19.0 kB] Get:7 https://apt.armbian.com stretch/main armhf Packages [334 kB] Get:9 https://apt.armbian.com stretch/stretch-utils armhf Packages [6,376 B] Get:10 https://apt.armbian.com stretch/stretch-desktop armhf Packages [2,211 B] Ign:5 http://cdn-fastly.deb.debian.org/debian str…

i have a RK3399 and a samsung-860-pro-512gb when i boot with this ssd connected using this official cable (which was recommended for this model by the orange pi manufacturer), i get this in dmesg: sd 0:0:0:0: [sda] Attached SCSI removable disk sd 0:0:0:0: Attached scsi generic sg0 type 0 but when i do `fdisk /dev/sda` i get `fdisk: cannot open /dev/sda: No medium found` when i put this ssd in my laptop, it is working correctly. i also soldered an alternive sata cable where the 12V power was connected instead of the 5V, don't remember exactly how, but that didn't work either.

Hi. I bought some time ago a OPi One and a OPi PC. Yesterday i tried to setup them with armbian without success until I switched images from one to another and...it worked. I think that the download page for each should be fixed ( 5.4.20 image ). Made me crazy as a beginner until I figured out, tried different micro sd cards, different power supplies... Sorry for my english. Many thanks for developers who makes something stable for this boards.

Hello help please. there is not sound in the headphones

I have an OrangePi PC and a BananaPi M1, and both of them are able to switch to USB host mode or device mode by editing dr_mode in corresponding .dtb file. But seems that both board are not able to support HNP protocol. From my understanding, OrangePi PC and BananaPi M1 only has perpherial-only OTG, please correct me if I am wrong. Is there any board that can support HNP? I need something that can switch USB mode(from host mode to device mode or the other way around) without reboot the board Any advice is appreciated

Hi all, I've met an issue on Banana pi M1 board. I'm trying to compile the driver for TP-Link T2UH USB (MT7610U) on BPI-M1. latest focal release cat /etc/armbian-release # PLEASE DO NOT EDIT THIS FILE BOARD=bananapi BOARD_NAME="Banana Pi" BOARDFAMILY=sun7i BUILD_REPOSITORY_URL=git@github.com:armbian/build.git BUILD_REPOSITORY_COMMIT=08297378c-dirty DISTRIBUTION_CODENAME=focal DISTRIBUTION_STATUS=supported VERSION=21.05.1 LINUXFAMILY=sunxi ARCH=arm IMAGE_TYPE=stable BOARD_TYPE=conf INITRD_ARCH=arm KERNEL_IMAGE_TYPE=Image what happening when i'm trying yo compile it. make[1]: Entering directory…

install https://github.com/emmercm/rpi-rtl8812au error? $ sudo make make ARCH=arm CROSS_COMPILE= -C /lib/modules/5.10.60-sunxi/build M=/sr/src/rtl8812au-f1bd10b modules make[1]: Entering directory '/usr/lib/modules/5.10.60-sunxi/build' make[1]: *** No rule to make target 'modules'. Stop. make[1]: Leaving directory '/usr/lib/modules/5.10.60-sunxi/build' make: *** [Makefile:1086: modules] Error 2

In fact, the whole dl/espressobin folder is missing.

Hi, I am looking for an OS for the BPi M2 Berry. Has anyone good experiences to share? Thanks a lot in advance, Friedrich I tried several OS, flashed with rufus.io No satisfying attempt yet. Last try is this: https://forum.banana-pi.org/t/bananapi-bpi-m2-berry-new-image-release-armbian-bullseye/14451

I have attempted to install OMV on my orange pi various times and i have had the same issue weather with the OMV after installation or with the armbian os before the OMV installation. when you start the system, it just won't get it's Ip automatically, at first i thought my orange pi came with a problem from fabric since I'm new to this but after attempting to put an Ip statically seemingly making it work I noticed that it just would not be set automatically. Now surely you might think it's a problem with my router set up, but this won't happen when I try it out with any other equipment in my house or when i just run regular Linux in my laptop, even when i run the OrangePi…

Hey the first time i tried armbian on tronsmart android box with sdcard , it was so seamless and so awesome. I am wondering if anyone has tried armbian on any android tablet. And it would be nice to support any of these tablets out there. In that way you don't have to worry about separate hdmi tv or monitor and accessories to use armbian. I always believe that arm's edge is in mobility, sleek and being minimal .

Hello, just registered on this forum because i can't troubleshoot my issue even if some posts seems to look like my issue and this forum doesn't unknown from me from some others reasons. Orange PI pc plus OpenELEC-H3.arm-7.0-devel-20161026221641-r23113-g64b34b3-opipcplus.img on eMMC since few months. After successfully make (for USB support) and tested 'u-boot-sunxi-with-spl.bin' on my SD card, i decided to write it onto the eMMC after booting from SD card with this kind of command: dd if=./u-boot-sunxi-with-spl.bin of=/dev/mmcblk0 bs=1024 seek=8 now i have this output (from UART) see bellow thanks in advance for help Philip63 …

I have been trying to install a minimal XFCE4 desktop environment onto my Orange Pi Zero 2+ H5 but have run into a weird issue. Here is the command I use... sudo apt-get -y install xorg lightdm xfce4 tango-icon-theme gnome-icon-theme which I had found elsewhere in the forums. The main issue I have is that I cannot start the desktop with the normal user account. It works if I startup with this... sudo startxfce4 which runs the root user desktop, but fails when I try to run it as just a user. Does anybody know what I have done wrong?

@TonyMac32 I have bought a Firefly-RK3399 from firefly ( http://shop.t-firefly.com/goods.php?id=45 ). I did not realize it at the time of purchase, but the Mosfets are unable to provide sufficient power for the board plus the USB ports, EDP connector, MIPI-CSI interface, M.2 slot, etc. I really love the IO of the board and want to try to find a way to get it to work (plus I don't have the money to go trying out more boards ). Would your idea help such a board? Thanks!

Hi all. This is not Armbian related. But I don`t know where else to ask. I`m doing research on the NanoPi DUO2 running FriendlyCore with kernel 4.14 for my next review video. I would like to film the video with the DUO2. For that I`ve got a camera, it works. But only at 7 fp/s. On the FriendlyARM wiki it sais: I tried searching for kernel 3.4. But I`m unable to find it(I think). This is what I get. I don`t think/know these are useable. pi@NanoPi-Duo2:~$ sudo apt-cache search linux-headers 3.4 linux-headers-3.4.0-1-hammerhead - Linux kernel headers for version 3.4.0 on Nexus 5 linux-headers-3.4.0-4-goldfish - Linux kernel headers for version 3…

Good morning I am using a tinkerboard S on Armbian Stretch. I would like to backup using rsync / rsnapshot to a remote nfs share. For the nfs server I tried an rpi3 on raspbian and on armbian omv4. The setup works, but on the actual job, copying a few GB, I get a kernel panic on the Tinkerboard Client everytime. The same jobs works flawlessly to local attached usb storage on the Tinkerboard. http://ix.io/1wJT Thanks for any input und happy Holidays! Sebastian

Hello there I have been using my orange pi zero as a network wifi adapter for my computer since it does not have one baked in. But this morning it stopped working. I reinstalled armbian hoping to fix the issue to no avail. I am running armbian 5.83 on opz and ubuntu 19.04 on pc. I attempted setting ethernernet to share network via guy nm as well as nmtui. I get an error from nmtui "could not activate connection: ip configuration could not be reserved (no available adress, timeout, etc) any help would be very appreciated.

Is anyone know how to set HDMI and LCD simultaneously on mainline kernel? We use a 3.5" LCD for which we made a patch (see enclosed). Now I'd like to have both HDMI and LCD showing the same framebuffer. Currently HDMI is only showing the console while signal is OK on LCD. Any hint would be appreciated. u-boot-sunxi-next.patch kernel-sunxi-next.patch

I try to update my jessie installation on orange pi one but I get errors. My kernel version is 3.4.113-sun8i My armbian.list file is this deb http://apt.armbian.com jessie main utils jessie-desktop My sources.list file is deb http://httpredir.debian.org/debian jessie main contrib non-free #deb-src http://httpredir.debian.org/debian jessie main contrib non-free deb http://httpredir.debian.org/debian jessie-updates main contrib non-free #deb-src http://httpredir.debian.org/debian jessie-updates main contrib non-free deb http://httpredir.debian.org/debian jessie-backports main contrib non-free #deb-src http://httpredir.debian.org/debian jessie-backport…

Hi guys, I've a nanopim4 V2 running Armbian Focal with Linux 5.7.15-rockchip64, on a Kubernetes k3s cluster, and I realise that time to time, the board crashes (or reboot) but I'm unable to find why. I've checked syslog kernel.log under /var/log.hdd without luck. What else should I check? This is the output of armbianmonitor if it's help. http://ix.io/2vgU Many thanks in advanced. Regards

So I have managed to partially pull out one of the usb sockets on my tv box. The little plastic piece that holds the 4 metal pins has come out while I was pulling out a slightly deformed usb cable. The box still worked while it was on. After a reboot it is not coming on. The LEDs and VFD don't come on. It doesn't boot into armbian or android. Is it safe to say that it is dead? I think I am going to have to try and lift those metal pins. Because they are touching the metal usb housing. Perhaps that is causing a short-circuit somewhere. If all else fails I will try to desolder the whole usb slot. Update: I have bent …

Hello All, It there a way to install Amiberry (Amiga Emulator)? I'm trying to set this up on my XU4 w/ Armibian Buster. Thanks

Hello all! Not sure if anyone saw this at all or not but the latest debian (11) now includes the panfrost and lima drivers! https://wiki.debian.org/PanfrostLima If I'm reading things correctly the needed bits and pieces (as well as a recent kernel) are in the packages "libglx-mesa0" and "libgl1-mesa-dri". Thought I would give this a go on a now (somewhat old-ish) Odroid XU4 device. It uses the mali t620 graphics chipset which I believe is in those panfrost drivers. I used the image file "Armbian_21.08.1_Odroidxu4_bullseye_current_5.4.142.img.xz". I did notice that the older kernel in that image (5.4.x) did not seem to detect anythi…

Hello everyone, I'm creating my coursework project and I should create my own C++ library for easier GPIO usage. I'm struggling with using epoll in my code, because it doesn't register edge events, that I specified. My code looks like this: void somePollingFunc(std::string path) { int epollFD = epoll_create1(0); if(epollFD == -1){ throw std::runtime_error("Failed to create epoll"); } int socketToRead = open(path.c_str(), O_RDONLY | O_NONBLOCK); if(socketToRead < 0) { throw std::runtime_error(std::string("Failed to open file\nPath: ") + path.data()); } // Creating epoll struct struct epoll_event gpioPollFD; gpioPollFD.data.fd = socketToRead; gpioPollF…

I tried to execute `sudo armbianmonitor -v` and I got this result. ``` Starting package integrity check. This might take some time. Be patient please... It appears you may have corrupt packages. This is usually a symptom of filesystem corruption caused by SD cards or eMMC dying or burning the OS image to the installation media went wrong. The following changes from packaged state files were detected: /usr/lib/chromium-browser/master_preferences.dpkg-dist ``` This is from new orangepi pc board and new SD Card with new install OS.

I am wondering if anyone else has had any success getting Armbian installed on a Banana Pi M5. I'm definitely a noob at this. After thinking the first M5 I tried it on was perhaps defective, but after trying on a second M5 I had the same result, board will not boot and the Green, Blue and Red lights on the board are all solid (not blinking). I'm afraid I may have bricked both boards. I used bpi-copy to flash the on-board emmc and did not receive any errors in the process. I am unable to boot from emmc or sd card at this point. I tried flashing the SD Card with Debian Bullseye and then on another attempt Ubuntu server (both images had worked previously) but to no ava…

Hello, I'm trying to control a relay (Bigtreetech Relay) by Orange PI 3 with Armbian 22.08.8 Jammy on it: the relay should be active as soon as PI started and deactivated on PI shutdown. As result I got the following device-tree overlay: /dts-v1/; /plugin/; / { compatible = "allwinner,sun50i-h6"; fragment@0 { target = <&r_pio>; __overlay__ { poweroff_pins:poweroff_pins { allwinner,pins = "PL2"; allwinner,function = "gpio_out"; }; }; }; fragment@1 { target-path = "/"; __overlay__ { poweroff: poweroff { compatible = "gpio-poweroff"; gpios = <&pio 11 2 1>; }; }; …

How can I access individual packages that make up the images that are available for download e.g. at https://www.armbian.com/lenovo-x13s/ ? I see only "full image" downloads and no link to information on what was used to build these images. I poked around the dists named "bookworm something" on apt.armbian.com looking for the kernel used, but didn't find any obvious match (no 6.3 kernel version, no kernel that has "x13s" in the package name, ...). Likewise, there is no x13s listed in https://github.com/armbian/build/tree/master/config/sources/families

Actual booting from eMMC and system including OMV from Sata SSD. Running boot & system from eMMC should be possible now and I would like to transfer system from SSD to eMMC without losing my config and starting from scratch again. That way I'll have a sdd beside the hdd for OMV. How can I manually transfer the system including OMV from SSD to eMMC and what configuration files need to be altered?

Hi all, Is there any working way to enable detailed logs from uboot? I am using fresh main branch (latest commit is 4648add1450c1b26bb29bf412ef054b0e978947d) . I have created following config inside userpatches/config-test.conf.sh file BOARD="orangepizero" BRANCH="current" RELEASE="jammy" BUILD_MINIMAL="yes" PREFER_DOCKER="yes" DOCKER_ARMBIAN_BASE_IMAGE="ubuntu:jammy" BOOTDELAY=2 UBOOT_DEBUGGING="yes" My command to build image is ./compile test. As I understand from source code UBOOT_DEBUGGING variable should enable such detailed uboot logs, but it seems like build framework ignored this option, I did not get detailed logs from uboot, also build logs do not conta…

Hello, Today i decided to install Debian Jessie (Vanilla) in my Cubietruck, boot was fine until the login. I can write the login (letters and numbers) but in the password field the keyboard doesn't work anymore, any help? Thanks

I work a lot with Raspberry including Zero Just bought several Orange Pi One The issue of power supply is annoying Same power adapter which will drive Raspberry smoothly fails to do the same for Orange Adding KB or Mouse also effects the stability, even adding one more computer to same power block had an effect on the orange As I need my machines in various locations I am concerned I will have issues

So I'm trying to modify a certain Mycroft skill (python) to be able to play local news. Here is the commit: https://github.com/marksev1/mycroft-core/commit/164c7207374131ece23a8ddf40c7a7981f3c7084 And this python script uses mpg123 to play the mp3 from the url. 1.) If I play the mp3 in the url from the terminal normally it plays every time. 2.) If I'd try to play it from that python script it only randomly plays and in the meantime i get errors regarding jack. See here, first time it succeeded then it failed multiple times: 2016-09-05 14:11:02,437 - Skills - DEBUG - {"message_type": "speak", "context": null, "metadata": {"utterance": "Here is the top of the…

@Igor Just an hour ago did a new build and got [ warn ] ... 30-real-time143-full-plus-rt-fixes.patch [ failed ] Up until this morning everything was fine but now the patch fails. It seems today's commits brake the RT.

Orange Pi PC = Server = Debian Jessie Programs does not start automatically at boot, I tested the deluge, transmission and vsftpd; Same commands used in Raspbian Jessie: Does not start automatic: sudo update-rc.d deluge-daemon defaults sudo update-rc.d transmission-daemon defaults

I try to type cyrillic symbols in mysql command prompt but symbols are not shown: for example: mysql> SELECT * FROM Partners WHERE `Name` = 'Игорь'; latin symbols are shown only. I try run /usr/sbin/dpkg-reconfigure locales but it didn't give results

I made a kernel upgrade which was not successful The kernel does not boot up. Unfortunately armbian does not contain a fallback method to load the old kernel. Therefore I need a way to restore the old kernel. I copied a working boot folder from another sdcard which does not work. What did I miss?

Now. the whole booting to login position coast 30 sec. I need reduce it to less than 10s(or 15s). Any reference, links, stuffs? Thanks at all !

This isn't Armbian per se, but I thought it worth mentioning for anyone considering a SOPine Baseboard. Pine chose a small coaxial power jack instead of the micro USB for the main 5V input. This jack is kind of an odd size, but it also seems pretty fragile, especially when the extra leverage of a power cable is added to it. I broke the mount on mine within the first 20 minutes of use. It still worked as it was just the mechanical mount, but it became position sensitive and a pain to use. You can still power the board via the Euler bus, and that's what I switched to instead. If this isn't appropriate for this forum, please feel free to move it (or d…

Hello all, Since a good year I'm using several Orange Pi's,yes several... And while doing some apt update/upgrade I'll see errors and want to know how to handle... 1) Showing up : Get:45 http://apt.armbian.com jessie/jessie-desktop Translation-en [178 B] Ign http://apt.armbian.com jessie/jessie-desktop Translation-en Question: What does this "Ign" mean and what to do that this error disappear? 2) Showing up on the end : Reading package lists... Done W: Duplicate sources.list entry http://security.debian.org/ jessie…

Hi everyone, I'm trying to get armbian running on an A20 based board. Been through the wikis (armbian and sunxi-linux) but I get a problem that is hard to figure out (for me). The board is an old tablet, know as Inet K100 (mine is branded Storex), and I'm trying to get the legacy kernel running on it to get a desktop install with LCD etc... Using sunxi-tools, I was able to get a fex file from the board. Spoiler [product] version = "100" machine = "K1001L1B" [platform] eraseflag = 1 [target] boot_clock = 912 dcdc2_vol = 1400 dcdc3_vol = 1250 ldo2_vol = 3000 ldo3_vol = 2800 ldo4_vol = 2800 power_start = 0 storage_type = 0 [clock] …

I am new to Armbian, please bear with me if I am making any wrong steps or assumptions. I installed the armbian bionics for the Asus Tinkerboard. I was expecting the netplan command and the /etc/netplan dir exist, but both are missing. Looks like it's not installed at all. Is there a way to have this working? I am already used to netplan to configure the networks. Thanks - purelight

Hi, I need your help I´ve a Beelink with home assistant and unfortunately the storage is full and now i cant access to home assistant or samba share to delete the files and reboot the BOX I access successfully with putty (root privileges) to my Box, but i can´t see the files to delete. There is some way to do this? @ - Sorry for my poor english. Thanks M8´s. Luis Belo

I am trying to figure out how to create a dtoverlay to allow my waveshare 2.8a fbtft screen to work. I understand that i the 5.x.y kernels, a dtoverlay is required. I'm starting with the waveshare32b.dts for raspberry pi, found here: https://github.com/swkim01/waveshare-dtoverlays Should be compatible with the 2.8a per waveshare wiki. I'm trying to modify it in sort of the same way as was done in this thread, for another display: The board I'm using for this is an orangepi pc2. But i don't' actually know what I'm doing. What I've come up with so far is this: /* * Device Tree overl…

Hi all, I bought a Orange Pi PC 2 a year or two back, loaded the Armbian image successfully and tweaked it until it was just right for my application. As this piece of hardware was going to live on a remote property, I bought another 2 Orange Pi PC 2 boards and some new SD cards with the intention of having 2 backups - one for development and the other as spare. I loaded these two up with the latest Armbian image and configured them as needed. These two work fine, even if I swap the SD card between these two pieces of hardware. However, when I try to put the SD card from the original Orange Pi PC 2 into one of the newer Orange Pi PC 2 it will …

I am building a legacy desktop image for Rock64 and there are a few things I am trying to customize at build time. I modified userpatches/customize-image.sh, but I am not getting expected results. Here are some things I am trying to modify: 1. I want to have the desktop come up in solid black color, no image. I made the following changes to userpatches/customize-image.sh: gsettings set org.gnome.desktop.background picture-options 'none' gsettings set org.gnome.desktop.background primary-color '#000000' But I am still seeing the Armbian image on my desktop. What else do I have to modify? 2. I need to get rid of the…

Hello! For some weeks now my BPM1 behaves a bit strange concerning video output. I used to connect my Banana to my monitor via a HDMI-DVI cable, which worked well for a very long time. Now, when I reboot the system, my monitor says "no signal", when I use that cable, as it does also when I use a pure HDMI-HDMI cable. The only way to make the Banana's video output work, is by using a HDMI-DSUB converter. But here comes the even stranger mystery: after I booted the Banana, using that converter, I can change the cable to whatever I want: HDMI-HDMI or HDMI-DVI, they both suddenly work again! But if I reboot the Banana again, not using the H…

I have a Ubuntu Server 18.04 with postfix installed and configure it the same way as I did on my Helios64 running Armbian 21.02.3 Focal. Last week, one of my older drives died in the Helios, but I didn't get an email about this. My Ubuntu Server 18.04 will send me mails as soon as there's an issue in the SMART values from the drive. I didn't had to configure anything to do that apart from postfix. I can send a test mail from both my Ubuntu Server 18.04 and my Helios64 Armbian and receive both. Any idea what the reason is that my Ubuntu Server 18.04 is sending me those emails by default and how I could enable this on my Helios64?

Looks like a missing gmp dependency? From armbian/build 5bfa587727f29a072b21ca936ab9f00ffdfbd502 == kernel == In file included from /root/armbian/cache/toolchain/gcc-arm-8.3-2019.03-x86_64-aarch64-linux-gnu/bin/../lib/gcc/aarch64-linux-gnu/8.3.0/plugin/include/gcc-plugin.h:28, from scripts/gcc-plugins/gcc-common.h:7, from scripts/gcc-plugins/randomize_layout_plugin.c:19: /root/armbian/cache/toolchain/gcc-arm-8.3-2019.03-x86_64-aarch64-linux-gnu/bin/../lib/gcc/aarch64-linux-gnu/8.3.0/plugin/include/system.h:687:10: fatal error: gmp.h: No such file or directory 687 | #include <gmp.h> | ^~~~~~~ …

Hey everybody, unfortunately no one could help me in OMV-forum due to a lack of armbian knowledge. Did all required preparations before running the upgrade script, nevertheless 6 services are broken afterwards, especially ifup/eth0. Apt update, apt upgrade and apt full-upgrade ran without problems before starting upgrade script. My system (set it up years ago with an amrbian-OMV3 image): # cat /etc/armbian-release # PLEASE DO NOT EDIT THIS FILE BOARD=raspberrypi BOARD_NAME="Raspberry Pi" VERSION=5.27 LINUXFAMILY=bcm2837 BRANCH=next ARCH=arm IMAGE_TYPE=experimental # lsb_release -a No LSB modules are av…

Good afternoon! Tell me about the case, please, the post is great, but maybe I'm initially going the wrong way. Initial task: data exchange between a remote server and equipment with a USB interface and CDC RS-232 or HID protocols. Putting a computer / laptop next to it is not an option. I did not find any ready-made solutions, there are only options: 1. Single board computer. Fast, cheap, angry, easy to make a case and PoE power from ready-made components on the market. 2. Arduino - to assemble from prototyping boards is long, difficult and expensive. To develop something of my own - the navel will be untied with my knowledge. 3. Hardware "e…

Test version of the Armbian+EDK2 system (UEFI\grub) is available. The system startup control is performed as on a regular PC - through the menu on the monitor screen, therefore, to fully use all the features of selective startup, you need to have a connected monitor and keyboard To use this option. Download the EDK2 image. https://users.armbian.com/balbes150/edk2/ https://disk.yandex.ru/d/kK6KIqHShRHLyw Unpack and burn to SD card. Download the Armbian image (kernel 6.1.0-rc7), For Station M2 https://disk.yandex.ru/d/C4Ql9v0BvhKPjQ For Station P2 https://disk.yandex.ru/d/5XuGz9WgF7FGCg unpack and …

I am trying to build Armbian using command below. I use 25.02.0-trunk armbian build version in docker. However I don't get kernel source package after succesful building. I get only following debs: armbian-bsp-cli-bananapim2zero_25.02.0-trunk_armhf__1-PC7e64-V62c4-H9299-B6e44-R7697.deb armbian-bsp-cli-bananapim2zero-current_25.02.0-trunk_armhf__1-PC7e64-V62c4-H9299-B6e44-R7697.deb armbian-config_25.02.0-trunk_all__1-SAfdf5-B8c21-R448a.deb armbian-firmware_25.02.0-trunk_all__1-SA8dbb-B6c7f-R448a.deb fake-ubuntu-advantage-tools_25.02.0-trunk_all__1-B34ac-R448a.deb linux-dtb-current-sunxi_25.02.0-trunk_armhf__6.6.65-S943e-D0531-P78f8-Cc98cH5c21-HK01ba-V…

Hello, everyone. Armbian website says OnePlus 8t is supported with "standard support" (here: https://www.armbian.com/oneplus-kebab/). I dont know what that includes as it is not very clear. Will one be able to do calls, send messages etc on that phone with Armbian (e.g. similar to sailfish os or ubuntu touch on their respective supported devices). I am basically asking if cellular, wifi, camera etc works fine.

Hi, Using Ubuntu (OPiPC/Ubuntu desktop/legacy) and the window borders are really 1 pixel thick, it makes it impossible to grab using only the mouse. I know about Alt+rightclick and Alt+F8, but I wonder if there is any other way to resize windows without occupying both hands. Any desktop applet that can configure the window border thickness?

Hello, I am running an orange pi one plus (H6 all winner). I tried to change partition size as suggested, although nothing working, here is what I tried: fdisk and the commands, with and without deleting old partition then adding partitions, I get an error message at the end when input w, people say to ignore it, although orange pi cannot boot afterwords I tried the instructions on their wiki, nothing works I tried cfdisk which seems to be working, although still when I df -h I cannot see the partition, and when I try to install something for some unknown reason my dpkg gets broken, and says that my mmcblk0p2 is …

I don't have a fiber/fast internet connection, and I get around 200kb/s download speed when I use normal apt or apt-get. But apt-fast accelerates download speeds significantly. I go up to 1MB/s using it (I set max connections option to 16 while installing it, you'll know what I mean when you try to install it using apt-add-repository, of course, if you don't know). So I suggest you to use apt-fast in "armbian-config" or any system utility. This suggestion goes to the developers. So that we (users with no good internet connection) can update the system or install the desktop environment a lot faster and easier.

There are updates in the most recent mainline kernel about the Odroid C0/C1/C1+ board: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/log/?h=v4.20&qt=grep&q=odroid The armbian image with the mainline kernel have not been updated. Could you please update it? I would like to use it. You can officially drop the outdated version with the kernel 3.10. The Kernel 3.10 is not supported any more and have ton of security issues that wont get fixed. Only the mainline kernel is interesting and worth upgrading to latest kernel. Thanks

Hello! I've got unnamed board with Allwinner A20 and FORESEE 8G memory, in completed device with HR215WU1-120 LVDS display. Spoiler It was working on Android 4.0 system, but someone needed to replace android with linux os system. LVDS display was lost when owner put SD card with linaro in slot for the first time. Now we have Linaro 14.04 command line, Spoiler and SD class 10 card with Armbian_20.02.0-rc1_Cubieboard_bionic_current_5.4.14 image, burned with Etcher. So. If power on without SD card - linaro starting in command line. If try to boot …

Hi Armbian forum team, i have bought some HC1/XU4, very fine boards, thank's, but have a wifi AP+STA pb. odroidhc1 / kernel: armbian 4.14 / wifi module 3 lsusb -> Bus 001 Device 002: ID 0bda:8176 Realtek Semiconductor Corp. RTL8188CUS 802.11n WLAN Adapter ). lsmod -> rtl_usb 20480 1 rtl8192cu After rebuild hostapd-rtl/driver (to suport nl80211)/AP + wpa_supplicant/STA runs fine but not simultaneously (when wpa_supp connects in STA (AP shutdown, etc..)). In fact that seems normal because in iw "combination is not supported" What 's the best chipset you advise me (rtl8812, rtl8814, rt3572/5572, mt7601, atheros, cypress) which supports AP+STA at SAME TIM…

Hi, Armbian gurus. I have make a new kernel and related modules for my pineh64 and want to test it. Thus they are not from dpkg. To test this kernel and modules. I have few questions: 1. About the symbolic links in /boot, are they all mandatory? What if I don't have an initramfs? 2. The Image linked file, is it have to be limited to certain compressed format to work properly? 3. Is there a recommended work flow to test a external kernel? Or I can just test by replacing Image, dtb, and the modules? Thank you.

Hey everyone, I am using a odroid c2 board with Armbien Buster image. I have a cheap bluetooth dongle and a usb sound card connected to the board. I am trying to use the board as bluetooht to aux input for my car. The board is working as expected when the a2dp profile is in use. But as soon as i place or receive a phone call i am getting garbage sound(garbage meaning a bunch of click like sound) after a while my phone drops the bluetooth connections and gives the sounds to earpiece on the phone. Also when the phone call places my syslog gets filled with "Bluetooth: hci0: SCO packet for unknown connection handle 0" I am using bluez5, alsa and pulsea…

I have a need for an additional 1G Ethernet connection on my XU4 running latest Armbian. Any recommendations?

Hi So I have upgraded my system with `apt update && apt upgrade`. How do I rebuild ZFS DKMS for the latest kernel? I have tried dkms_autoinstaller but it does nothing. I uninstalled and re-installed zfs-dkms package and this worked, but there's gotta be a better way? Thanks! a

This Android device uses a Linux4.4 kernel. Considering that my nanopc-T3 lacks the functions required by a higher version of Linux, I would like to transplant the 4.14 version of Linux to this Android device at most without the bootloader source code. What's interesting about the device tree? It seems that the kernel provided by the device manufacturer includes some device drivers that are not included in the Linux kernel nativery. will cross-version compilation be a problem? https://github.com/LineageOS/android_kernel_motorola_msm8998

[ OK ] Reached target Power-Off. [ 915.658031] reboot: Power down ERROR: a3700_system_off needs to be impPANIC in EL3 at x30 = 0x000000000402326c x0 = 0x0000000000000000 x1 = 0x00000000d0012000 x2 = 0x0000000000000000 x3 = 0x0000000000000000 x4 = 0x0000000004027b00 x5 = 0x0000000000000000 x6 = 0x0000000004027a88 x7 = 0x0000000000000001 x8 = 0xffffff80000809f0 x9 = 0xffffffc0114dba30 x10 = 0x0000000000000040 x11 = 0x000000000402d138 x12 = 0x0000000004030e40 x13 = 0x0000000000000000 x14 = 0x0000000004031932 x15 …

I was hoping to get some idea if it would be possible to build Armbian for the ODroid OGU (S922X, similar to N2+) using a different Kernel. Specifically, using the version from JelOS (https://github.com/JustEnoughLinuxOS/distribution) who have made really good progress for this specific device. I've been building JelOS and modifying packages etc, but would prefer to use Armbian if possible. Any help appreciated.