Beginners

While using ubuntu1604-kernel4.4-VAAPLI.img I took downloaded from the server, I came across the following problem. While trying to develop device drivers for kernel space, I realized we dont have any linux headers in the said system. I have tried looking up for the same at Rockchip's github as well as wiki site, but could not find one. Can anyone point me to the correct linux headers ? I am using RK3288 development board, and current my version using "uname -r" is "4.4.55+"

Hello Everybody: I'm having problems to create and save a new partition to eMMC on BPI M2Ultra board. As you can see on the attachd image below, the fdisk -l command, list the mmcblk1 with the right size (7.3 GB), them, i start creating a new partition (n command) and writing the partition table (w command), but once created the new partition never gets to the disk, and a new fdisk -l command shows the disk like it was before. Of course, whithout a partition i can not format the eMMC and can not use nand-sata-install. This doesn't happen with bananapi original images as there was no issue to create the partition and save it to the disk …

Hi all. I am new in both OrangePi hardware and Armbian OS. I bought Orange Pi Zero 512 MB. I aim to develop a stand-alone device using this board. I am too confused with my readings. Do you have any idea for the following run rules together on the same board? (1) When I connect via serial (USB), it runs bash. It will ask user name and password. I can write a program, compile it, update the OS, and change settings. <This part is okay.> I want to use a GUI for this part. (2) When I supply 5-Volt power via extension pins, it runs stand-alone. It will not ask for a username and a password. It starts with an application developed in either Python or C programming lan…

Hello everyone.. below is from a board with a bad flash, or download. Spoiler HELLO! BOOT0 is starting! boot0 version : 4.0.0 rtc[1] value = 0x00010000 rtc[2] value = 0x00020000 rtc[3] value = 0x00030000 DRAM DRIVE INFO: V1.0 DRAM Type =3 (2DR2,3DR3,6:LPDDR2,7:LPDDR3) DRAM normal_mode value: 00000001 DRAM CLK =720 MHZ PMU: AXP81X ddr voltage = 1500 mv using ic H8 using axp AXP818 DRAM zq value: 00003bfb dram size =2048 card boot number = 2 card no is 2 sdcard 2 line count 0 [mmc]: mmc driver ver 2014-8-11 15:06:39 [mmc]: ***Try SD card 2*** [mmc]: mmc 2 cmd 8 timeout, err 00000100 [mmc]: mmc 2 cmd 8 err 00000100 [mmc]: mmc 2 send if cond failed [mmc]: mm…

I have orangepi one I get compilation errors I do not know how to handle https://www.dropbox.com/sh/0kast2unzyg6sux/AADz143tOM2Lqg2bYF-OneK5a?dl=0

Can someone please help me? I have a banana pi M3 board, and once got an Armbian image in this site https://www.armbian.com/bananapi-m3/ , and loved it! used it for a year, then my SDCARD have an issue, when i came to get the image link again all the links disappeared from the page, these images arent availble anymore? can someone please help me find an armbian image for bananapi m3 again?

NanoPC-T4 only has 16GRAM, which is still a bit small for daily use. So I want to put u-boot on emmc or sd card, and install the system on nvme solid state drive. If I want to realize this function, can the armbian-config tool help me realize it quickly? Or do I need to set u-boot parameters and compile by myself, thus installing the system in nvme SSD?

Hey all, I've been using Allwinner boards for the last couple of years and Armbian+forums have made this a workable thing that I promote to my friends as being The Way To Go instead of being a big fat waste of time. Igor + Tkaiser (and anyone else forgive me if I didn't give you a shout) - You fucking rock. You really do; you've all provided amazing amounts of support for multiple kernels and userspaces and in the face of (at least) bullshit from the chip vendors, yet you are absolutely crucial to them being taken seriously. The work from Armbian has (for me) made the difference between BananaPi, OrangePi, etc all being an unusable washout of #ShitDidn'tW…

Contemplating whether or not I should pull the trigger and buy a new camera. Images were taken with an OV5640 camera attached to an orange pi PC. The first image is a good image, then after a few hours of use I start getting issues; reading images either times out and/or results in corrupted images. (Note: All images were rotated 90 degrees clockwise) https://imgur.com/a/LEyl1h9

Hi, I have a Banana Pi-R1. I want to use this device as a customized router. I need an operating system with a graphical user interface. Because I will use it with a firewall with a graphical interface. I cannot decide the appropriate operating system. Which operating system and which graphical interface should I install? I tested LXDE on Bananian but it wasn't successful.

hello, everybody, I am new here, nice to meet you. I like reading books about electronic, can you recommend some books for me? thanks in advance

Hello, I will use the integrated CAN-Controller with the actual version of Armbian Bionic (or Buster) on the BananaPi-M1 Actually it is not possible to activate the CAN-Bus. I had activate the CAN in the armbian-config. After a reboot I the CAN0 is not integrate in the list from "ifconfig -a". What are the steps to activate the CAN-Bus on the BananaPi M1. Many thanks, André

Hi I've installed Armbian_21.02.3_Tinkerboard_focal_current_5.10.21.img on my Tinkerboard. # uname -a Linux tinkerboard 5.10.21-rockchip #21.02.3 SMP PREEMPT Mon Mar 8 07:34:33 UTC 2021 armv7l armv7l armv7l GNU/Linux I'm not able to create a bridge with a WiFi interface: brctl addbr br0 brctl addif br0 eth0 brctl addif br0 wlan0 can't add wlan0 to bridge br0: Operation not supported wlan0 is the onboard WiFi. I also tried several usb WiFi dongles with the same result. Any hint? Regards, Chris

I am not able to boot from armbian. First I downloaded image from (https://www.armbian.com/orange-pi-zero-2w/) later on I flashed the image with usbimager, then since this didn't work I did with balena etcher, (all those in linux). Balena etcher crashes at verification so then I did with my windows machine, first with usbimager and since it wasn't working I decided to decompress the .xz and do it with "rufus" Here i attach the images and as you guys can see it says "failed to mount /dev/mtdblock4". That terminal is pretty much useless, I can't even do reboot or poweroff. I just need armbia…

I am trying to install box86 and possibly box64 on my Orange pi zero 2w. I tried using armbian-gaming as well as following the instructions found here, and attempting to build box86 with both resulted in a gcc error unrecognized command line option '-marm' Upon attempting to build box64 with the instructions, I get a make error 2, and the topmost error is a ccl error unknown value 'loongarch64' for '-march' This seems to be cross-compilation errors, but IDK what steps to take to fix it. Thanks in advance! QuowLord

When using Armbian on my Orange Pi 5b, I can't select 120hz when the resolution is 4k but I can when it's set to 1080p. In other distros like Joshua Riek's Ubuntu and the official Orange Pi 5 Ubuntu release, 120 hz is selectable in 4k and works wonderfully. Is there something I'm missing somewhere? Is there something I can do to manually enable this somewhere? This distro checks all the boxes for me otherwise. Using 120 hz makes a massive difference when streaming games from my desktop to my living room TV using Sunshine/Moonlight.

Hello, I got recently an Odroid HC2 and installed Armbian (Buster 5.4.61) on it, OMV5 and I fixed IP. I configured it on the cable that I use on my desktop and connected my desktop on wifi. When I finished the configuration, I put HC2 closer to router on another cable and connect my desktop on the cable that HC2 was connected. If I try to connect to SBC through Putty on the desktop with it connected on cable and wifi, I connect normally. But if I disconnect of wifi, I can't connect to SBC, even on Putty or browser. Does anyone know what I'm doing wrong?

Dear guys, Recently i am trying to install Armbian on orange pi pc plus using Mobaxterm but for some reason after finishing the installation it shows only Armbian-config screen but not the GUI interface. I don't know if I installed it right or wrong. Hope everyone can help me because this is a subject project of mine in university. Thanks so much.

Please, help me find an old version of firmware for Nanopi Neo Air. I'm looking for Armbian 5.73 Debian based 4.19.20-sunxi . Best regards

So I'm seeing this up as a media device for my aunt who has nothing but an old crt TV. So I tried h3droid for user ease, but it's not near stable enough and crashes whenever anything is running any load on the cpu. Retro orange pi gives her a desktop and easy interface for watching movies/tv shows and playing old games. The problem I'm running into is I can't get any media file to play. I get sound but no visuals on Kodi and VLC I've tried converting the files from mkv to MP4, I've tried changing codecs h.264->h.265. I don't know what to do because she will never understand/use a command prompt so I wanted to hook her up with something easy.

Hello, should I load any module for using SPI to communicate with NFC reader PN532? My device is opi one and itead PN532 nfc reader. BTW, If I try to use i2cdetect, dmesg get flooded by error message. Here is a part of error message :

Hi, I'm running Ambian 24.11.2 Noble Genome version on OrangePi 5 Plus in my nvme drive. I want to change my system language to Chinese simplified. However, when I select 'Chinese simplified' in 'Settings -> System -> Region & Language -> Manage Installed Languages -> Install/Remove Languages' and click 'Apply'. It says: 'software database is broken. It is impossible to install or remove any software. Please use the software manager "Synaptic" or run "sudo apt-get install -f " in terminal to fix this issue at first.' I did tried to run synaptic with sudo and clicked 'Fix Broken Packages' and 'Reload'. It says 0 is broken, 0 to install/upgra…

Hello, when I run dietpi-software and select some software to install, it gives me this error. Can someone help me? I had to install armbian on my Rock64 and then ran the install dietpi script. Thank you DietPi-Software: G_AGUG │ - Exit code: 100 │ - DietPi version: v6.19.6 (Fourdee/master) | HW_MODEL:22 | HW_ARCH:3 | DISTRO:4 │ - Image creator: Dev │ - Pre-image: armbian │ │ Log file contents: │ Reading package lists... │ Building dependency tree... │ Reading state information... │ Calculating upgrade... │ 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. │ 1 not fully installed or removed. │ After this operation, 0 B of addition…

I bought OPi 3 with 8 GB emmc, installed Armbian for OPi3, buster version, in the instructions I found a way to transfer the system to emmc - the nand-sata-install command. Then my actions: 1. Without apt update/upgrade try run nand-sata-install. There is only one option in the window that appears - Install/Update the bootloader on SD/ eMMC. Ok > WARNING > ok > done > ok. Reboot without sd > OPi3 not booted. Nothing changed. 2. apt update/upgrade, try run command. Only one option - Install/Update the bootloader on SD/ eMMC. Ok... Nothing changed. What do I do wrong, maybe the version is not that, or do you need to download something? In the …

I built an image from source using compile.sh and assumed that the first time login credentials were root 1234 but they do not work. What are the correct credentials and/or where can they be sent when building the image?

I have orange pi one zero. I buy extended Nas card for orange pi zero. After install extended board, i can't logging in system. Root or user password not accept system) Try logging with UART and SSH. Try copy new password in shadow on my PC. But system not accept any password. Maybe system himself change password after changing system or some problem with bash? p.s. I have Bpi M2p too and last month was the same situation. But console not accepted any login and after enter "root"....again asked to enter login. I rewrite new Armbian and return to work.

Armbian trixie 24.2.0-trunk.272 - kernel 6.7.0-rc7 Connecting over ssh. When I shutdown the pi (sudo poweroff) it disconnects the ssh session but does not shut down completely. Network and heartbeat leds still flashing. Works fine with the legacy kernel 5.10 What am I missing? thanks

Hi, I can't record audio from I2S interface on Lime2 (A20) Ubuntu_trusty_3.4.112. For record the sample 60 sec. (44.1K 16bit) I used this command: arecord -D hw:1,0 -t wav -c 2 -f S16_LE -r 44100 -d 60 test.wav File is success created and recorded, but absolutely nothing sounds. Why I can't write sound?

I just downloaded the March 26th nightly of Stretch for Rock64. Getting the following error running apt-get update/apt-get upgrade: E: The repository 'http://beta.armbian.com stretch Release' does no longer have a Release file. N: Updating from such a repository can't be done securely, and is therefore disabled by default. N: See apt-secure(8) manpage for repository creation and user configuration details. root@rock64:~# Re-imaged with a new Flash drive and still getting the same issue. Is there a problem with beta.armbian.com tonight? Thanks!

I'm trying to run any standard Armbian image on QEMU on my Ubuntu machine, and I found this post on this forum. I installed QEMU with: sudo apt-get install -y qemu I downloaded "Armbian_20.08.1_Orangepione_buster_current_5.8.5.img" and copied the following files from the image file with PowerISO to a directory, "/myfolder": 1. boot/vmlinuz-5.8.5-sunxi 2. boot/initrd.img-5.8.5-sunxi 3. boot/dtb-5.8.5-sunxi/sun4i-a10-cubieboard.dtb I then ran QEMU with the below command: qemu-system-arm \ -M cubieboard \ -m 1024 \ -cpu cortex-a8 \ -dtb /myfolder/sun4i-a10-…

Hi! I've just downloaded the Armbian_23.8.3_Orangepi3-lts_bookworm_current_6.1.53_cinnamon_desktop.img onto a 16GB SD card, plugged it to the Opi and started it up. Then I connected to it using SSH, and it works just fine. But when I tried VNCViewer (actually, MobaXTerm on Windows), nothing is displayed but a message saying that Cinnamon crashed and "you are currently running in fallback mode". I've tried to install another window manager, like lightdm with xface4 with no success. I also tried to remove cinnamon and reinstall it, again to no avail. I did the same to x11 and again couldn't have any desktop manager running. Then I burned t…

Hello there I have been using my orange pi zero as a network wifi adapter for my computer since it does not have one baked in. But this morning it stopped working. I reinstalled armbian hoping to fix the issue to no avail. I am running armbian 5.83 on opz and ubuntu 19.04 on pc. I attempted setting ethernernet to share network via guy nm as well as nmtui. I get an error from nmtui "could not activate connection: ip configuration could not be reserved (no available adress, timeout, etc) any help would be very appreciated.

Hi there, this might be a dumb question but I've done some searching and haven't gotten any closer to a solution, so, my apologies. I need to connect to my NanoPi M4 over the serial UART because I've made the eMMC unbootable, and I need to tell the board to boot from microSD so I can fix it. I've attempted to do this in both 'minicom' and 'screen' at 1500000 8N1 and the result is the same either way. I can see output from the NanoPi just fine, but when I attempt to send characters, it only displays a question mark imprinted on a square for each character, similar to what I'd expect if e.g. the character was not in my terminal font. It's not just a …

Hi All, I have successfully installed a brand new armbian on my H616 OrangePiZero2 Board. I have installed docker and have several containers running on it. one of the dockers need to scan a cifs drive that contains Hebrew characters and it fails on scanning - not retrieving all the files. I have tested the same on a raspberry pi running Ubuntu18.04 and it works great and retrieved all the files without any issues on armbian it was ~300 files and ubuntu ~900 files. The name of the files can not be changed since they are used out side of the docker. basically files are been saved in Hebrew on the cifs mount all the time. I have done a…

I just installed Armbian Bionic (latest version) onto a Tinker Board (non-S). Connected to my home wireless network. Chromium works fine except when trying to access my Google Account. I get: All my other phones, iPads and PCs are fine. Please help! P.S. I don't think I can install Google Chrome either.

Hi All, I am a total newbie in orange pi and ambian. I just want to use orange pi one as my pi hole server. i use sandisk ultra pro 32G a a huawei 2A power block using usb to barrel connector. After my first install, and try to ssh, the port 22 timed out in armbian I also tried reflashing to debian, and still cannot ssh. I already tried some suggestion i found like dpkg-reconfigure openssh-server, changing time out of ssh. i tried armbianmonitor -u, but im getting a Network/Firewall problem detected. you think this might be related to ssh connection. thanks!

Hi! I have Orange Pi Pc Plus and Armbian based on Linux 5.8.11-trunk which successfully loads with any U-Boot taken from official Armbian distro. However I need to do minor changes in U-Boot KConfig (Allow store env vars in ext4). For that purposes I cloned U-Boot from its GitHub repo and build it. make CROSS_COMPILE=arm-linux-gnueabihf- orangepi_pc_plus_defconfig make CROSS_COMPILE=arm-linux-gnueabihf- This make me a u-boot-sunxi-with-spl.bin file which I transferred to my SD card. The U-BOOT loading step passes well, and I've seen "Starting kernel ..." However kernel doesn't start. I've set VERBOSITY=7 in armbianEnv.txt and seen that kernel load…

Hi i have had my linux box turned of for a very long time and i was trying to run updates but it doesnt seem to want to update, is there something i can do? im very green when it comes to Linux. I tried to do the url command but it didnt work: root@pine64:~# sudo armbianmonitor -u System diagnosis information will now be uploaded to <!doctype html> <html lang=en> <head> <meta charset=utf-8> <title>&nbsp;</title> </head> <style> body { font-family: monospace; margin: 2em; } </style> <body> <p>ix.io is taking a br…

Hi, I setup a Radxa Zero 2 last week with Klipper, a 3d printing firmware. Over the past few months, I've transitioned my printer to using canbus. I'm finding the setup process slightly different with Armbian than it was on RpiOS, and I'd appreciate feedback or pointers that could help me better understand networking in Armbian. I use a usb canbus adapter. In the past, I've configured it using the standard Klipper config written to `/etc/network/interfaces.d/can0`: allow-hotplug can0 iface can0 can static bitrate 1000000 up ifconfig $IFACE txqueuelen 1024 So, when I went to setup the Radxa, I did what I've always done, and i…

After downloading and installing (legacy ubuntu trusty) v 4.5 and doing apt-get update && apt-get upgrade (to v4.6) I ran nand-sata-install to boot and run from nand, my board won't boot because of script is invalid and unable to parser boot.ini. I still can boot from my SD-card the following information is displayed boot0 version : 1.5.0 dram size =1024 Succeed in opening nand flash. Succeed in reading Boot1 file head. The size of Boot1 is 0x00056000. The file stored in 0X00000000 of block 2 is perfect. Check is correct. Ready to disable icache. Succeed in loading Boot1. Jump to Boot1. [ 0.177] boot1 version : 1.5.0 [ 0.177] pmu type = 3 […

Hi, I know that this device is obsolete, but will be grateful if having any kind of support. I'm trying to build an image for Armbian for Mele A1000 but no success. Here is the log: [ o.k. ] Preparing [ host ] [ o.k. ] Build host OS release [ hirsute ] [ o.k. ] Syncing clock [ host ] [ o.k. ] Checking for external GCC compilers [ .... ] downloading from mirrors.dotsrc.org using http(s) network [ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz ] [#409dbb 24MiB/24MiB(99%) CN:1 DL:651KiB] [ o.k. ] Verified [ PGP ] [ .... ] decompressing [ .... ] gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz…

Hi, Trying to build a full installation for an Orange Pi One. Building on a DigitalOcean ubuntu 15.10x64 host with 20Gb free disk where apt-get update has been run. I followed the instructions here: https://github.com/igorpecovnik/lib The build fails with Installing Armbian on top of Debian Jessie base system ... bridge-utils Installation of package failed. Screenshot: http://screencast.com/t/uDyMUyPMSnVL What am I doing wrong? The reason I am trying to do this is because I would like to create a custom Armbian where the wpa_supplicant.conf is preloaded with my home wifi information, so I can just boot these cards headlessly and they'll…

Please forgive me if I posted this in the wrong category. My immediate task isn't related to P2P, but my end goal of setting up a personal server is. I am attempting to compile a custom image with https://github.com/botter-nidnul/userpatches. You can read more about the project here https://urbit.org/grants/urbian-a-customized-linux-distribution-for-urbit-appliances. I can compile a focal image without customization, but when I attempt to customize the image, I get `umount: /home/nebulay/repo/project/armbian/build/.tmp/rootfs-d412f0e4-e33c-4c0c-909b-9042f7924589: target is busy` This repeats until I hit ctrl+c. I get an image, but it fails to boot. I have googled it, and…

Hi, I'm having some trouble with my OrangePi Zero with Armbian running with Armbien. I'm trying to setup a proxy with the IP address and port without any success... I need the proxy to be for everything (http, https, ftp..) I've tried everything I found on google : - editing /etc/apt/apt.conf.d/10proxy with : Acquire::http::Proxy "http://proxy_server_address:port"; - editing /etc/environnement with : export http_proxy="http://proxyipaddress:proxyport" (also https, ftp, no_proxy) - editing visudo with : Defaults env_keep+="http_proxy https_proxy no_proxy" - uncommenting /etc/wgetrc where the proxy is enabled - adding in ~/.bashr…

Suddenly after updating via armbian-config I lost ssh access and found the port closed. I rewrote the latest armbian version, stuck the sd card in, connected to ethernet cable via router and started up. The red and green lights were on as they should be and the internet cable was flashing green. Waited 3 minutes and checked the ports with nmap. And the port is closed again. Not responding to ping at all. I am still new to this topic. Please help and sorry if the translator translates crookedly.

I cannot get the console connection to work I've used Putty on Windows but there seems to be no COM3 starting up?

Hi, hardware / OS = OrangePi PC with Armbian 22.04.2 Ubuntu When executing following command "ssh -D 1080 user@domain" the system doesn't create / open ssh port where it should listen too. I can verify this with command "ps aux | grep ssh". I edited /etc/ssh/sshd_config file by enabling following lines AllowTcpForwarding yes PermitTunnel yes What else do I have to do in order to be able to start ssh proxy server? I was following this guide https://www.digitalocean.com/community/tutorials/how-to-route-web-traffic-securely-without-a-vpn-using-a-socks-tunnel Thank you.

Hi, I'm trying to download the image to add to my sd card, but all the images I tried downloading, either through direct link or torrent, give me this error: Internal error - code should not reach this point I couldn't find any information about this anywhere, and it is happening with all the images and versions. Can someone please help me download them? Thanks!

I was hoping for some pointers on this issue I am having while trying to enable eth0 interface on my Pine64 SBC. I am running the following Armbian version: Title: Armbian 5.38.180128 Pine64 Debian stretch next Kernel: Linux 4.14.15 Build date: 28.01.2018 I am able to connect a USB 2.0 to Ethernet adapter without any issues. The problem arises when I try to enable eth0 which is the Native Ethernet port. pine64:/# ifconfig eth0 up SIOCSIFFLAGS: No such device dmesg | grep eth0 gives me the following: xxxxxx.ethernet eth0: Could not attach to PHY var/log/messages shows the following: device (eth0): driver '(null)' does not…

Hello, I am running as usual my orange pi one plus H6 ALL WINNER with ubuntu server and cannot find my exFat HDD on it, it detects the usb but not /dev/sda and cannot mount or access it, yes I tried with ntfs This is what I see (image below), should be 232 GB HDD connected via USB, sata is not an option What should I do?

Hi Trying to install docker (arm64) via the debian documentation on Docker's website, but running into persistant problem with dpkg on docker-ce. This is a fresh install (good SD card) of Armbian_20.08.1_Nanopim4_buster_current_5.8.6.img. (Made with dd, I confess). No ssh yet, so I'll handtype the some terminal output: ... Job for docker.service failed because the control provess exited with error code. See systemctl status docker.service" and "journalctl -xe" for details. invoke-rc.d: initscript docker, action "start" failed. - docker.service - Docker Application Container Engine Loaded: loaded (/lib/systemd/system/docker.service; enabled; vendo…

I'm new to boards with linux and this is my very first attempt to install linux systems on board so there might be something that I cannot be aware of. I tried to install armbian v6.12 on the SD card but after I finish configureing the setup, the wifi doesn't work. Unfortunately I have no wires to connet to the board so now it is unable for me to connect the board to the internet. The problem is exactly the same as the post Wifi module AX210 - Orange Pi 5 Plus - Armbian Community Forums. I can see the network controller through `lspci -v`: And the dmesg shows that iwlwifi cannot find suitable version to use: And I indeed have the…

I recently bought a used OrangePi 5, when it arrived it had a working Ubuntu image on an SD card. I decided to format the card and put my own image of Armbian on the card using the Armbian imager. when installed the card would no longer boot. lights on board but black screen no HDMI output. I tried several different SD cards and different images all with the same result (A1 Sandisk cards) Eventually I tried a hail mary and put an Armbian image on a really old USB thumb stick and it immediately booted and worked just fine. I tried putting the OrangePi os on one of my SD cards for kicks and it gets HDMI output but is just stuck on th…

Hello everyone! I try to install game library for Python 3 (via pip) PyGame. After downloading package, i get message below: pip install pygame Defaulting to user installation because normal site-packages is not writeable Collecting pygame Downloading pygame-2.1.2.tar.gz (10.1 MB) ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━ 10.1/10.1 MB 3.5 MB/s eta 0:00:00 Preparing metadata (setup.py) ... error error: subprocess-exited-with-error × python setup.py egg_info did not run successfully. │ exit code: 1 ╰─> [30 lines of output] WARNING, No "Setup" File Exists, Running "buildconfig/config.py" Using UNIX configuration... …

I am with Armbian (ubuntu 18.04): Linux rockpi-4b 4.4.213-rockchip64 and when I installed chromium and tried to login gmail, I got below: Couldn't sign you in This browser or app may not be secure. Learn more Try using a different browser. If you’re already using a supported browser, you can refresh your screen and try again to sign in. The chromium version info: Version 80.0.3987.163 (Official Build) Built on Ubuntu , running on Ubuntu 18.04 (64-bit) Tried chrome UA spoofer with other UA text like safari or firefox, still the same feedback, no luck still. Any ideas?

Hi, I have a nanopi neo SBC and my final goal is to get Sunxi-cedrus 2019.03_Release (patched kernel 5.0.0 release) installed on device to test cedrus driver. Did a manual kernel build and tried to dpkg -i *.deb files on the board but the kernel hangs on boot. I read also but that didn't help me so much So I tried same procedure to replace the armbian standard 4.19.20 kernel with an official mainline 4.19.36 version. I found same exact issue so I think I'm missing something. Please have a quick read at the procedure I followed and put any advice to help me going through. 1) touch default kernel .config to have: -…

I just successfully installed Armbian buster, when I run apt-get update the message appears: root@aml:~# apt-get update Err:1 http://security.debian.org buster/updates InRelease Could not connect to prod.debian.map.fastly.net:80 (151.101.8.204). - connect (111: Connection refused) Cannot initiate the connection to prod.debian.map.fastly.net:80 (2a04:4e42:2::204). - connect (101: Network is unreachable) Could not connect to security.debian.org:80 (133.242.99.74). - connect (111: Connection refused) Cannot initiate the connection to security.debian.org:80 (2401:2500:103:11a::74). - connect (101: Network is unreachable) Err:2 http://httpredir.debian.org/d…

Hi everyone, I'm an experienced Debian user but it's my first time with Armbian running on an Orange Pi Zero. I'd like to make it a DB node by running MySQL. As there is no MySQL available in the apt repository, I tried MariaDB but during the installation (tried multiple times) I don't get asked for a password and need to run mysql --skip-grant-tables which leads to db failure, permission problems (like root can access without password while all the other users are blocked). Installation from source code fails due to limited memory. How can I seamlessly get mysql-server to work on Armbian?

Hello, I upgraded the system on Banana Pi Pro to Armbian_21.11.0-trunk_Bananapipro_buster_current_5.10.60 and it stop seeing SATA HDD. Log entries are: Oct 11 13:01:21 bananapipro kernel: ahci-sunxi 1c18000.sata: supply ahci not found, using dummy regulator Oct 11 13:01:21 bananapipro kernel: ahci-sunxi 1c18000.sata: supply phy not found, using dummy regulator Oct 11 13:01:21 bananapipro kernel: ahci-sunxi 1c18000.sata: supply ahci not found, using dummy regulator ... The problem also persists on the new clean install on any Armbian Flavor (buster/bulleye/focal/hirsute). ahci.txt journalctl.txt lsblk.txt uname.txt

Is there any description how to setup the boot logo? I tried what I found: in build/packages/blobs/splash change logo.png and run command line with "BOOT_LOGO=yes", it doesn't work. After I found "What we use now is plymouth". OK. Does it work in compile time? I don't have plymouth after installing armbian in a docker container. How should I use plymouth (if it is the only way) to make a boot logo in compile time?

Installed desktop, ran start desktop. From there I was back in text mode. Rebooted still no desktop. Tried startx, xinit and, several other start desktop commands from various OS's. I've been working on this for 3 days now. Don't know what I'm missing. I also tried installing lightdm, no change. I could also use the shut down command. Tried everything I could think of there too. Any help would be greatly appreciated. I hate wasting your bandwidth and time. I'm stuck! I'm done wasting bandwidth and moved to time now. Funny it asks me startx like in (OS name). Wish I knew how to tell it Yes! exactly lol! Thanks in advance ROC-RK3328-CC Armbian 5.98 Renegade

Hello everybody, I am using Armbian Bullseye image on an ODROID-HC2 and I moved the root filesystem to an encrypted SATA drive. During boot in UART / USB serial console I see that two services fail to start: Resets System Activity Logs and Haveged [...] [ OK ] Reached target Sockets. Starting Armbian hardware monitoring... Starting Armbian hardware optimization... [ OK ] Started RPC bind portmap service. [ OK ] Finished Armbian hardware monitoring. [ OK ] Reached target Remote File Systems (Pre). [ OK ] Reached target Remote File Systems. [ OK ] Reached target RPC Port Mapper. [ OK ] Stopped Entropy Daemon based on the HA…

Hi, i can't get usbip work, there's a tutorial or something else that i can follow to make usbip working over that soc board? cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=18.04 DISTRIB_CODENAME=bionic DISTRIB_DESCRIPTION="Ubuntu 18.04.1 LTS" #/usr/bin/usbip WARNING: usbip not found for kernel 4.14.84 You may need to install the following packages for this specific kernel: linux-tools-4.14.84-sunxi linux-cloud-tools-4.14.84-sunxi You may also want to install one of the following packages to keep up to date: linux-tools-sunxi linux-cloud-tools-sunxi The boa…

Hello! Trying to build legacy buster desktop image for orangePi4 ends with error Processing triggers for libc-bin (2.28-10+deb10u1) ... Processing triggers for systemd (241-7~deb10u8) ... Processing triggers for dbus (1.12.20-0+deb10u1) ... [ o.k. ] Checking MD5 sum of installed packages [ debsums ] [ error ] ERROR in function create_rootfs_cache [ main.sh:588 -> main.sh:549 -> debootstrap.sh:59 -> debootstrap.sh:343 -> general.sh:0 ] [ error ] MD5 sums check of installed packages failed [ o.k. ] Process terminated [ error ] unmount_on_exit() called! [ main.sh:1 -> image-helpers.sh:0 ] [ o.k. ] Unmounting [ /home/lord/build/.tmp/…

Hello everyone, I'm creating my coursework project and I should create my own C++ library for easier GPIO usage. I'm struggling with using epoll in my code, because it doesn't register edge events, that I specified. My code looks like this: void somePollingFunc(std::string path) { int epollFD = epoll_create1(0); if(epollFD == -1){ throw std::runtime_error("Failed to create epoll"); } int socketToRead = open(path.c_str(), O_RDONLY | O_NONBLOCK); if(socketToRead < 0) { throw std::runtime_error(std::string("Failed to open file\nPath: ") + path.data()); } // Creating epoll struct struct epoll_event gpioPollFD; gpioPollFD.data.fd = socketToRead; gpioPollF…

I am using an Armbian (on Orange Pi Zero 512) as a print server. I can not install the printer driver Canon MF 4418 (MF4400 series). On Canon site there are drivers only for x86 and amd64, but as i understand, i need arm (or may be armhf). Can someone help?

Im not sure if this is the right forum. Ive also Googled and found similar problems, but no solution that works for me. So Im happy to be LMGTFY with some hints, or shown the right forum :-) Im running an OrangePi Zero on Armbian (lsb_release reports Ubuntu 16.04.3 LTS). I have networking set up with both ethernet and wifi. Both work. But I want to have ethernet as static IP, and wireless as dhcp. My config looks like this: allow-hotplug eth0 iface eth0 inet static address 192.168.4.122 netmask 255.255.255.0 gateway 192.168.4.1 broadcast 192.168.4.255 dns-nameservers 8.8.8.8 8.8.8.4 allow-hotplug wlan0 auto wlan0 iface defaul…

Am i not looking in the right place ? I am trying to get the image for this board. But I cant seem to find a download link. I proceed to look at other boards and I dont see download links anywhere. Some insight on this normally trivial task would be appreciated. https://www.armbian.com/renegade/

sudo add-apt-repository ppa:liujianfeng1994/rockchip-multimedia [sudo] contraseña para eduardo: Repository: 'deb https://ppa.launchpadcontent.net/liujianfeng1994/rockchip-multimedia/ubuntu/ bookworm main' Description: This ppa provides a package rockchip-multimedia-config to config your system ready for multimedia acceleration. sudo apt install rockchip-multimedia-config Then you're good to go. More info: https://launchpad.net/~liujianfeng1994/+archive/ubuntu/rockchip-multimedia Adding repository. Press [ENTER] to continue or Ctrl-c to cancel. Adding deb entry to /etc/apt/sources.list.d/liujianfeng1994-ubuntu-rockchip-multimedia-bookworm.list Adding …

I cant use the number keys on my keyboard to type in 1234 as the manual says. I can only type in "root" at the login but I cant type anything in the password section.

im using orange pi with armbian and i try to rotate display by seeting in boot/armbianEvt.txt fbcon=rotate:3 it only rotate the console message. but when i run startx (startx installed via sudo apt-get install --no-install-recommends xserver-xorg x11-xserver-utils xinit openbox ) is still default mode not rotated It makes me angry to know that i have achieved it without any difficulty with a RaspberryPi 3 simply by adding display_rotate = X in /boot/config.txt and that there is no way for Armbian.

Hi, Could anyone please help me to configure CB3 and the subboard RAID? In fact, I own a CB3 and the RAID subboard with two SSD 120GB that I bought at Cubietech three years ago and I have already assembled it. I use the Armbian distribution for Cubietruck and I installed it on a SD Card, but now I would like to install this distribution (Armbian for CB3) on the two SSD from the SD card. If I type the following commands 'hwinfo --block' or 'fdisk -l' or 'lsusb' or 'lsblk -o name' at the prompt (as root), I do not see any SSD except the SD Card (mmcblk0) I also launched 'armbian-config' but nothing appear in the menu about that. I have done some onl…

I'm looking for help getting cec working on a Le Potato. i3Desktop image from this page - https://www.armbian.com/lepotato/. I’m getting the following error with cec-ctl: Failed to open /dev/cec0: No such file or directory

for installing cedar here is a guide: http://www.orangepi.org/orangepibbsen/forum.php?mod=viewthread&tid=878&extra=page%3D1

Hi, I'm trying to work with the CedarX/Cedrus Video Engine (on Allwinner A20). It works smoothly with my patched FFmpeg; for example: ffmpeg -f v4l2 -r 30 -pix_fmt nv12 -video_size 1280x720 -i /dev/video0 -vcodec cedrus264 -pix_fmt nv12 -qp 15 -f rtsp -rtsp_transport tcp rtsp://192.168.10.11/live/test I need to use pixel format RGB24, but as far as I understand, I'm limited to work with NV12 (or NV16) pixel format. Does this limitation is due to: My FFmpeg patch (I think not...) CedarX/Cedrus driver implementation. Hardware limitation. Thanks for the help, Joseph

Hi, I'm trying to work with the CedarX/Cedrus Video Engine (running in Allwinner A20). It works smoothly with my patched FFmpeg; for example: ffmpeg -f v4l2 -r 30 -pix_fmt nv12 -video_size 1280x720 -i /dev/video0 -vcodec cedrus264 -pix_fmt nv12 -qp 15 -f rtsp -rtsp_transport tcp rtsp://192.168.10.11/live/test I need to use pixel format RGB24, but as far as I understand, I'm limited to work with NV12 (or NV16) pixel format. Does this limitation is due to: My FFmpeg patch (I think not...) CedarX/Cedrus driver implementation. Hardware limitation. Thanks for the help, Joseph

Attempted to work with both latest Bullseye and Focal images for OrangePi R1 but in both instances got the following message: E: Failed to fetch https://xogium.performanceservers.nl/apt/pool/focal-utils/w/wpa/hostapd_2.10-6~armbian22.02.3+1_armhf.deb Certificate verification failed: The certificate is NOT trusted. The certificate chain uses expired certificate. Could not handshake: Error in the certificate verification. [IP: 104.36.81.15 443] E: Unable to fetch some archives, maybe run apt-get update or try with --fix-missing? Pasted here (duplicate of above) as well valid 90d. http://paste.debian.net/plain/1238152

See title, currently can't update/upgrade on EU mirrors.

Hello, I've some trouble to install K3s on my OrangePi Zero2, somewhere I read it could be a kernel problem (not activated). I get following message. Can someone help me? Apr 08 20:39:15 oPi2 k3s[4055]: time="2022-04-08T20:39:15+02:00" level=info msg="Run: k3s kubectl" Apr 08 20:39:15 oPi2 k3s[4055]: time="2022-04-08T20:39:15+02:00" level=fatal msg="failed to find cpu cgroup (v2)" Apr 08 20:39:15 oPi2 systemd[1]: k3s.service: Main process exited, code=exited, status=1/FAILURE Apr 08 20:39:15 oPi2 systemd[1]: k3s.service: Failed with result 'exit-code'. Apr 08 20:39:15 oPi2 systemd[1]: Failed to start Lightweight Kubernetes. k3s.service - Lightweigh…

Hi, Have Arduino (microcontroller) clone with CH340 USB/UART (USB serial port). Does armbian support it? regards Peter

Hi All, I have a BPI-M2 ZERO, BANANA-PI-ZERO with SERIAL to USB plugged in. It's being detected by lsusb Bus 002 Device 005: ID 1a86:7523 QinHeng Electronics CH340 serial converter but it doesn't appear under /dev/ttyUSB0 The problem is that I can't see it under /dev/ as /dev/ttyUSB0. I haven't tried installing CH340 drivers yet. Should I use the ones for Ubuntu? Here is the tutorial I found but I'm not sure if those are the correct drivers: https://learn.sparkfun.com/tutorials/how-to-install-ch340-drivers/all uname -a Linux bananapim2zero 6.2.13-sunxi #1 SMP Wed Apr 26 12:30:09 UTC 2023 armv7l GNU/Li…

Hello everyone, I have an M2+ and want to change the IP to fixed. So I put these lines in etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.2.30 netmask 255.255.255.0 gateway 192.168.2.254 Than it did not work after a reboot, so I checked and did this change # Wired adapter #1 to Wired adapter #1 but now I can not reach it at all. Please help me out to fix this.

Hello after some search i successfull attack Ibutton on 1 wire, using ibutton probe my problem is that by default kernel scan for slaves every 10 seconds. Want to change it to 1 second or less if possible. Searching a bit, on some linux distributions this solves the problem: modprobe wire timeout=1 slave_ttl=5 modprobe w1-gpio but since in arbian /arbianEnv.txt take care of modules loaded, it do not work, My current file is: verbosity=1 bootlogo=false console=serial disp_mode=1920x10[D80p60 overlay_prefix=sun8i-h3 overlays=i2c0 pps-gpio uart1 uart2 uart3 usbhost1 usbhost2 w1-gpio param_pps_pin=PA6 param_w1_pin=PC3 rootdev=UUID=6de…

Hello Pin A18 is HIGH when OPI ONE boots but I want to change OPI ONE pin A18 to LOW. How could I do this?

Sorry, I change this topic to the correct path: http://forum.armbian.com/index.php/topic/630-change-micro-sd-paths-to-memory-mount-paths-cups-package/ I want to write microSD card as less as possible and CUPS package uses the following path's by default (although can be changed): /var/cache/cups /var/log/cups /var/run/cups /var/run/cups/printcap /var/spool/cups /var/spool/cups/tmp But I think this paths are pointing to micro SD card (except .'/var/log') (or not?) root@pcduino3nano:/etc/cups# df -h Filesystem Size Used Avail Use% Mounted on /dev/root 7.3G 1.1G 6.0G 16% / devtmpfs 500M 0 500M 0% /dev tmpfs 128M 212K 128M…

I have been going over forum after forum trying to figure out how do this, and nothing seems to match up. I just downloaded MySQL on my new Rock64. The OS is installed on a 32GB eMMC, and I have a 1.5GB USB 3 HDD installed for my home folder and all the user data. I bought this to be set up as a LAMP server, and have installed Apache and PHP, which are working well. I haven't had any luck with MySQL though. It seems that nothing matches the documentation. All the documentation and forums say that the configuration file is located at /etc/mysql/my.cnf In that configuration file, there's supposed to be DB location settings,…

Hi. My custom board has two PHY devices in the same bus. But I don´t know how to change to use the other one. alr@lime2-emmc:~$ dmesg |grep eth0 [ 10.888810] eth0: PHY ID 02430c54 at 0 IRQ 0 (sunxi_gmac-0:00) active [ 10.893616] eth0: PHY ID 283400c2 at 8 IRQ 0 (sunxi_gmac-0:08) Thanks!

I had problems When i tried- To change root password at Boot as asked and the system always halted.i tried différent sd card and goût the sa me issue. What should i do?

Got a cli install on my OPi5 and have it connected to a small screen I have on my desk, link here, but the terminal has big borders on the sides, and the text is very small, how can I make the text bigger and get rid of the borders? Spec for size is 1024X600 16:9

ı have a lcd as ' http://s.aliexpress.com/NjiyQFvE ' . I do all the connections correctly but the LCD screen does not appear. At first, a white light comes out on the screen. I could not find a manual or guide about this LCD. How can ı chane the resolution as http://www.orangepi.org/Docs/LCDModule.html

Hi, I have "ARMBIAN Debian GNU/Linux 10 (buster) 4.6.5-sunxi" running on a BananPi R1 router. I used to have it set up such that while it booted off the SD card, it had its root FS on an SSD. Some time ago, I had to re-install as an upgrade went fatally wrong and now I cannot remember the exact steps to switch from the SD card to the SSD as the root FS. I changed the root= in /boot/boot.cmd and generated the /boot/boot-scr and also changed the /etc/fstab entry but findmnt -n -o SOURCE / still shows "/dev/mmcblk0p1". Can anyone tell me the steps to take in switching to a new root FS? Thanks and ... stay healthy! Josef

Can someone PLEASE guide me how to get rid of the lousy build-in desktop and switch to MATE_

hi, Question: Is it possible in armbian Desktop version, Change user name and rename directory / home / user So that armbian start with the new desktop? thanks from spain

How to change font / view size in qbitorrent. The menu items are very small. In the settings under Appearance no effect on the font size in qbittorrent. $ hostnamectl Static hostname: Icon name: computer Machine ID: 4147 Boot ID: 129d Operating System: Debian GNU/Linux 10 (buster) Kernel: Linux 5.4.20-rockchip64 Architecture: arm64 $ uname -a Linux RockHomeServer 5.4.20-rockchip64 #20.02.1 SMP PREEMPT Mon Feb 17 04:45:00 CET 2020 aarch64 GNU/Linux Thank you very much!

Armbian 22.05.0-trunk with bleeding edge Linux 5.16.20-rockchip64 my armbian runs on a MKS SKIPR motherboard for a 3d printer. Since I updated the system, I can no longer change any files. I change it but after a restart the file is back as it was.since i have updated the system for example this file nano /etc/resolv.conf After saving and restarting everything is as it was. no matter whether as root or user Is there a setting that prevents or reverses changes?

I'm running Armbian on an Orange PI zero and I want to change the default ftp port because I have another device on my network that uses ftp and I want to forward the port. FTP seems switched on by default, I didn't install it so I don't know which ftp program it is.

I've had two Cubietrucks running almost flawlessly for about 10 years on Armbian/Buster and previous versions. I recently decided to install Bookworm using Armbian_23.8.1_Cubietruck_bookworm_current_6.1.47.img.xz. On this I encountered several problems, whose causes I never fully uncovered, but got over them. One of these problems was that neither manual setup nor the use of armbian-config allowed for a lasting configuration of the German keyboard layout, although "Personal Setting" says the opposite (see att. image No.2). It's a pain in the neck, really. All I could filter out is a commandline message that's only visible a second. See the last screenshot with fou…

Hello Igor, I want to put my own stuff inside motd. I'm not sure which scripts are responsible. In /var/run/motd.dynamic there is your banana text, but this is dinamically changing. how is the best approach to exchange the motd on your distros? Regards José

Hello, I'm trying to enable I2C access in U-Boot, for orange PI zero. I've downloaded the Armbian build, and tried to compile with CREATE_PATCHES, exactly like the tutorial here: https://zuckerbude.org/armbian-using-create-patches/ However, the build never stops and waits for me to make changes. I've attached the build log. I *think* I just need to add the following lines to orangepi_zero_defconfig: CONFIG_I2C0_ENABLE=y CONFIG_I2C1_ENABLE=y I guess that would be my next question- is this the proper way to change this config is via CREATE_PATCHES? I tried just changing the defconfig file and re-running c…

Hi to all! I am using Orange PC Plus and wanted to connect small display to it. I wanted to have display as ready device : in casing, with power etc. So I bought this one Aliexpress link It has HDMI, VGA and A/V input and for 35-45 USD only. Resolution (described) - 1024*600/800*480 Works with Raspberry Pi3 OK! But I need linux board with built-in eMMC memory. So I bought Orange PC plus. But it does not cooperate with this display in any modes, avaliable in h3disp (including 800*480). Also it doesnt work via my HDMI to VGA converter and A/V input is not compatible too. May be somebody have some experi…