Advanced users - Development

Hi, running Armbian Ubuntu on Nanopi Neo2 and it is working really great. I would like to implement HPN-SSH but I can't compile any of the OpenSSH versions against OpenSSL 1.1.x present on system. Any idea if OpenSSL 1.1.x can be safely downgraded to the latest OpenSSL 1.0.x release? I would use for example the method described here Not sure if OpenSSL 1.0.x would break anything on the system or not? Thanks for your help and advise!

Ubuntu x64, Bananapi jesie with -next kernel. First try yesterday: everything default, changed only BUILD_DESKTOP to yes image was built with 4.1-rc8 kernel / version of image was 3.1 few errors at the end (perl did not like some locales that were not set and probably some error with resizefs, partial log attached) Image was not bootable, banana did not show anything, behavior was the same as banana without inserted card Second try today: deleted /output/output/* deleted compile.sh and created new one with latest content image was built with 3.19.7 kernel (why that downgrade?), version of image was 3.2 banana boots but cannot remount filesystems. That leads to reb…

Hi, after pure installation Armbian_4.5_Lamobo-r1_Debian_wheezy_3.4.109.zip, the log is full of GMAC messages: [43099.518189] GMAC TX status: VLAN frame [43099.521192] GMAC TX status: VLAN frame [43099.524646] GMAC TX status: VLAN frame [43111.775611] GMAC TX status: VLAN frame [43112.963963] GMAC TX status: VLAN frame [43112.980989] GMAC TX status: VLAN frame [43112.986370] GMAC TX status: VLAN frame [43112.989681] GMAC TX status: VLAN frame [43112.992410] GMAC TX status: VLAN frame [43112.996184] GMAC TX status: VLAN frame [43113.002038] GMAC TX status: VLAN frame [43113.973308] GMAC TX status: VLAN frame [43113.976078] GMAC TX status: VLAN frame [43114.143583] GM…

Hello, I am using my Renegade with the Armbian I compiled myself. Now there is only one partition on my system: Number Start End Size Type File system Flags 0.03MiB 16.0MiB 16.0MiB Free Space 1 16.0MiB 5580MiB 5564MiB primary ext4 5580MiB 7620MiB 2040MiB Free Space I want to add a boot partition like Raspberry OS, so I can make some configration on the PC through boot partition. Raspberry OS's partition always like that: Number Start End Size Type File system Flags 0.02MiB 4.00MiB 3.98MiB Free Space 1 4.00MiB 260MiB 256MiB primary fat32 …

Hello. I am finished Armbian Jammy 22.05 Bulseye edge 5.16.20 gnome desktop on a Rockpi4 (rk3399). When I try to overclock from Armbian-config, it doesn't work. That is, I can enter the application, apply rockchip-rk3399-opp-2ghz.dtbo. Then reboot, go to armbian-config and set a new unlocked CPU clock speed of 2.2Ghz. But instead it is only available up to a maximum of 1.8hz. How can this be fixed? Do I have to create an image from scratch, or maybe there is some trick?

I've start looking about the Switching DEV to 5.0.y ... I've done a preliminary trial for OrangePiPCPlus after disabling few patches, etc ... Installed with success ... Although it produce at lot of patch rejects, I think we should pursue the move to 5.0.y, even if it looks more painful than the switch from 4.19.y to 4.20.y done few weeks ago ... I'm also calling for help on this move, as I've seen lot of patch rejects in Lima patches : @JMCC are you the expert here ? For all Devs wishing to keep backup images of 4.20.y, build your images ASAP before the switch occurs ! Any concerns ? EDIT: Oh ! I alm…

Hi guys, do you have idea why boot stopped? Check log below please. It was build about 25minutes ago but about 1 week younger build was working. U-Boot SPL 2017.03-armbian (Apr 03 2017 - 19:48:42) DRAM: 256 MiB Trying to boot from MMC1 U-Boot 2017.03-armbian (Apr 03 2017 - 19:48:42 +0100) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi Zero DRAM: 256 MiB MMC: SUNXI SD/MMC: 0 *** Warning - bad CRC, using default environment Setting up a 720x576i composite-pal console (overscan 32x20) Error: no valid bmp image at 66000000 In: serial Out: vga Err: vga Net: phy interface0 eth…

Hi Igor, I'm trying to build and update the kernel for the Lime2 board using the script you provided on github. I'm using linux sunxi 3.4.103. The only changes i've made in the kernel are in the sunxi-codec.c file, where i'm changing the values to some variables which should impact the latency on voip softphones. Here are the changes that i'm doing in "static struct snd_pcm_hardware sunxi_pcm_playback_hardware" and "static struct snd_pcm_hardware sunxi_pcm_capture_hardware" { - .period_bytes_min = 1024*4 + .period_bytes_min = 16*2 - .periods_min = 4 + .periods_min = 2 } The problem is that after running the script i get the tar file with 5…

I'm looking for Orange Pi RV2 RISC-V support. This board is gaining popularity due to the Orange Pi manufacturer's good reputation with Arm. I have successfully built both Orange Pi and Raspberry Pi aarch64 builds on Debian from source so I'd like to know how to build Armbian for Orange Pi RV2 riscv64. What would I need to modify in the build process? Thanks!!

It is appearing like that only in recent builds ...

Hello, I have been building images for the NanoPC-T4 with armbian successfully in the past. However I now get the error "could not resolve 'ports.ubuntu.com'" when the build tries to install ping_5.1-1_arm64.deb (full log below). Do you have any idea what this comes from and how I could solve/debug this ? Thank you Additional info : I added 8.8.8.8 as an alternative DNS server on my machine, I can ping ports.ubuntu.com successfully. I have cloned the armbian build and head points to this commit https://github.com/armbian/build/commit/5b8d86ae5f6f34cf6cc13edf6b1def2773f66f0a Best regards, Rick …

Dear gurus good afternoon. I ask for help because itself I don't understand any more what not so I do. I should make a clone of my sdcard, but nothing leaves. I tried so: I find the sdcard fdisk - l I create the empty file of an image dd if=/dev/zero of=armbian.img bs=2048 count=1402144 also I add him to loop losetup/dev/loop0 armbian.img now I clone the sdcard in loop the device dd if=/dev/sdd of=/dev/loop0 now I write down a half-scientific image on new sdcard dd bs=2048 if=armbian.img of=/dev/sdd As a result my sdcard doesn't seem on linux and I can't mount sections and loading doesn't happen to sdcard. Prompt please in what a mistake and as to me to make a clone of …

Hi, I'm in need of help with the I2S "drivers" for Arch Linux ARM and the A20 processor. I need to create a 4-wire I2S output. 1. BCLK 2. LRCLK 3. DATA 4. MCLK = 256xfs I can't seem to work out how to make #4, a Master Clock fixed at 256 * Fs. I've been using this code as a starting point: https://github.com/dan-and/linux-sunxi/tree/dan-3.4.current/sound/soc/sunxi/i2s and I am not a Kernel developer. At all. Thanks.

i've cross-compiled all possible backported drivers for legacy 3.4.112 kernel could someone who has some usb tuners or video grabbers test it? download and untar http://d-h.st/k4kZ cd there and run sudo make install

Since about four weeks we encounter out of memory issues when building an Armbian image on GitHub with a customize-image.sh script. We had no big modifications on the build system since then, we have to rebuild from time to time to get the latest version of our application into the image. We already use a more powerful runner (32GB RAM, 8 cores). Our compile call: ./compile.sh \ BOARD=rockpi-4b \ BRANCH=edge \ RELEASE=bookworm \ KERNEL_CONFIGURE=no \ BUILD_MINIMAL=yes \ NETWORKING_STACK="network-manager" \ COMPRESS_OUTPUTIMAGE=xz \ KERNEL_BTF=no \ SHARE_LOG=yes Our build is based on the tag v25.8.0-trunk.260 Any ideas for this? Thank…

Hi! Sorry if this is kind of wrong posting, but I had an failure on compiling first for the Banana Pi for the Debian Stretch, complette image but without any other changes. Just wanted to compile a complete image for the Banana Pi, but got an error that terminated the compilation. After that I made a new image with the Ubuntu version with any problems. Thought that it might have something to do with the old hardware so I tried to compile another one for the Asus Tinker board for the Debian Stretch, but that gave me similar problems with termination of the compilation. Here is the some few lines of the output chip_5.34_all.deb". [ o.k.…

Hi, the building of 4.14.17 ended up with the following error: CC [M] drivers/staging/rtl8723bs/os_dep/xmit_linux.o LD [M] drivers/staging/rtl8723bs/r8723bs.o AR drivers/staging/built-in.o Makefile:1028: recipe for target 'drivers' failed make: *** [drivers] Error 2 [ error ] ERROR in function compile_kernel [ compilation.sh:341 ] [ error ] Kernel was not built [ @host ] [ o.k. ] Process terminated Any hints? Regards, A.

Hi Igor, I encountered an issue on Bananapi with kernel 4.2 using your latest SDK: A reboot or powercycle will fail with getting eth0 up and running (no IP address). I tried these both combinations: u-boot: 2015.04 + kernel: 4.2 u-boot: 2015.07 + kernel: 4.2 dmesg delivers: [ 13.387092] sun7i-dwmac 1c50000.ethernet: no reset control found [ 13.394879] Ring mode enabled [ 13.402647] No HW DMA feature register supported [ 13.402814] Normal descriptors [ 13.418061] TX Checksum insertion supported [ 13.498887] libphy: PHY stmmac-0:ffffffff not found [ 13.507177] eth0: Could not attach to PHY [ 13.515283] stmmac_open: Cannot attach to PH…

I have searched all the forums, can't find a way to use compile.sh build a image with the kernel to be 4.9.0 version. Is there a variable some where to set this? the latest 4.9.4 and 4.9.3 are not working well for my nanopi or my orange zero. and yes, i went through all the docs, and tried I can. -jerry

Hi all, there is an issue with SPI on a Banana Pro (A20). I am on mainline kernel 4.5.5 now, but the problem already occurred on 3.4.109. SPI transfers are way to slow for my application, independently from the SPI clock. Investigating the SPI signals it turned out that there is an enormous delay between CS going active (low) and the transmission starting. The delay is in the magnitude of 10...20 usec which is a large multiple of the pure transmission time, so increasing the SPI clock does not solve the problem. The connected device is an SPI TFT display, so I have to send a large number of SPI words of 2 bytes each, where CS must toggle after each word (required by th…

My objective is to boot Armbian on my NanoPi Neo2 from a network server. I've got Armbian running on the NanoPi Neo2 and u-boot recognizes the ethernet interface. Also, I have a DHCP server and TFTP server running. If I press space during start-up, I get in the U-boot environment. When I give the dhcp command in the U-boot environment, the NanoPi Neo2 get's an IP address and loads /boot/boot.scr from the network. So, the pre-requisites seem to work fine. But then.... I just can't figure out how to start Armbian (preferrably in read only mode) from the network. Maybe someone can tell me what needs to be done. I've got the following qu…

I'm testing with bananapi m1 plus(ARMBIAN 5.31 stable Debian GNU/Linux 8 jessie 4.11.6-sunxi) I want to remove booting output both in the lcd screen and the serial console(because I am using the ttys0 for other purpose), so changed /boot/boot.cmd. I found these two line, if test "${console}" = "display" || test "${console}" = "both"; then setenv consoleargs "console=tty1"; fi if test "${console}" = "serial" || test "${console}" = "both"; then setenv consoleargs "${consoleargs} console=ttyS0, 115200"; fi and changed it with those two lines below. if test "${console}" = "display" || test "${console}" = "both"; then setenv consoleargs "console=tty…

Hi, I have been recently working on a couple of extensions: lvm and cloud-init I forked off "v23.11.2" tag when creating my branches, since they are extensions, and wont alter the framework much. Today I noticed that OdroidUX4 is not building, but it was building last week. A patch seems to be failing. I guess it is a kernel/driver patch. Then my question is: is it possible that, on the same tag (v23.11.2), builds break? I am starting to think that the tag is only for the build process/patch set, but excludes, for example a reference to kernel code. I suppose then the situation is that a kernel update…

Finally Canonical launches an official Ubuntu 18.04.1 LTS (Bionic Beaver) Beta for Raspberry Pi 3 boards http://cdimage.ubuntu.com/releases/18.04/beta/ Maybe is interesting to check the repos.

I compiled the Armbian on renegade board, based on mainline linux, compiling was stopped as the output: LD vmlinux.o MODPOST vmlinux.symvers MODINFO modules.builtin.modinfo GEN modules.builtin LD .tmp_vmlinux.kallsyms1 [ error ] ERROR in function compile_kernel [ main.sh:589 -> main.sh:490 -> compilation.sh:506 -> general.sh:0 ] [ error ] Kernel was not built [ @host ] [ o.k. ] Process terminated And the logs files are in the attachments. Today the linux kernel auto updates to 5.15.36, I haven't this issue using 5.15.35 before. Anybody know why? logs.zip

Was wondering if there are any kernel update scripts i can use to update from http://mirror.igorpecovnik.com/kernel/ http://mirror.igorpecovnik.com/u-boot/ would be nice im open to colab on a script if there isn't any

Today i have tried to boot armbian on my old tablet. After i copied script.bin from tablet nanda partition and applied it on Armbian_5.20_Lime-a10_Debian_jessie_3.4.112_desktop image desktop has started. The first thing i have checked is CPU temperature 65 - 67 'C - 1008MHz 300Mb of 512 free mem Not working: 1) touch screen 2) wifi 3) accelerometer Is it normal 65-57 'C for Allwinner A10 CPU ? And how to add support for wifi and touch screen ? hardware: cpu Allwinner A10 wifi Realtek RTL8188CUS touchscreen raysens rs10f160904 ssd2533qt6 ddr3 x4 h5tq1g83tfr-h9c flash x2 29f32g08 lition power system axp209

Dear Friends, this is Judy from Banana Pi team. We will have BPI-M2S and BPI-R2 PRO sample ready on May. If you have interesting and ability to develope the software for these two boards, please contact me, my mail: judyhuang@banana-pi.com Look forward to cooperate with you!

Greetings, I haven't built a new image for awhile. But, I wanted to refresh the process. In the meanwhile, the only change I've made is upgrading my host. My build platform is a VM. I have no idea if that matters, but it was a change. I now have some weird errors/warning and I want to troubleshoot them. How can I enter into the environment to run just the customize script and commands? I'd like to dig into them, but not sure how. Thanks!

Possible addition for stock Armbian builds...adds quite a bit to the terminal based graphical status https://github.com/cjbassi/gotop Spoiler https://github.com/cjbassi/gotop/raw/master/assets/demo.gif

Hi, If I build my kernel 'properly' using the armbian compile.sh script with docker, everything works fine. If I run the docker image interactively, go into /armbian-cache/_data/sources/linux-pine64/my-hacks-1.2 and do export PATH=/root/armbian/cache/toolchains/gcc-linaro-5.4.1-2017.05-x86_64_aarch64-linux-gnu/bin/:$PATH make ARCH=arm64 CROSS_COMPILE="aarch64-linux-gnu-" -j8 $* I get a kernel that seem to work in every way, except it won't load any modules. The 'normal' build uses modules in /lib/modules/3.10.107-pine64. The non-compliant kernel reports uname -r of 3.10.107+. I tried copying the existing /lib/modules/3.10.107-pine64 to /lib/modules/3.1…

I repurposed my old build system hardware and am trying to build a new one. Nice faster box ;] On this new linux host I create a virtualbox machine and install Hirsute from the link in the documentation. I do an apt update / upgrade. I install git and clone the build directory according to the documentation. Everything seems to go well until it gets through a lot of the .o files and gives [error] ERROR in function compile_kernel [ main.sh:574 -> main.sh:479 -> compilation..sh:506 -> general.sh:0 ] the line above is always the same, although it comes after different .o files for different boards. I've rebuilt the virtu…

Aside from the DNS resolution issue I am having (different thread), I am often getting stuck on the following: Unpacking locales (from .../locales_2.13-38+deb7u8_all.deb) ... Processing triggers for man-db ... Setting up locales (2.13-38+deb7u8) ... Generating locales (this might take a while)... Generation complete. Generating locales (this might take a while)... en_US.UTF-8... done Generation complete.​ It just sits there and nothing further happens. I have left it for 30 minutes or more, and still nothing. I usually end up killing it... rebooting and then restarting. When it does get past this, I typically end up with the debian sources DNS resolution is…

Hi all, since i didnt want to manualy start building images for the boards i have, i decided to make a automated script for this. Now i finished the script i wanted to share it with everyone: cd /home/alexander/build ./compile.sh KERNEL_ONLY=no KERNEL_CONFIGURE=no BOARD=orangepiplus2e BRANCH=next RELEASE=xenial BUILD_DESKTOP=no FORCE_USE_RAMDISK=yes USE_CCACHE=yes ./compile.sh KERNEL_ONLY=no KERNEL_CONFIGURE=no BOARD=orangepiplus BRANCH=next RELEASE=xenial BUILD_DESKTOP=no FORCE_USE_RAMDISK=yes USE_CCACHE=yes ./compile.sh KERNEL_ONLY=no KERNEL_CONFIGURE=no BOARD=orangepizero BRANCH=next RELEASE=xenial BUILD_DESKTOP=no FORCE_USE_RAMDISK=yes USE_CCACHE=yes ./…

Dear Community, Currently Im playin with my Banana Pi M2 Berry and therefore I need a fusion of the LATEST Armbian -System with the compilers needed by the Boards Offical "GPIO-Libarys", which are outdated 7years ago. The most important libary would be the RPi.GPIO. RPi.GPIO The problem is, that this libary was using python2 and python3, python2 isnt my future i think, but for compiling the lib with python3 I need some pip-packages and the right arm-gcc compiler = 4.8 i think. DO i may need a cross-compile libary or whats are the requirements to build the lib on the latest system? To avoid hardware-d…

Hi, I'm trying to build an image for the Orangepi Zero Plus 2 (H3) using the following instructions: https://docs.armbian.com/Developer-Guide_Build-Preparation/. After putting the produced image onto a microSD card using dd, I put the card into the board, connect the serial and power, and then seems to fail and drops me to the u-boot prompt. Here is the output of the terminal. U-Boot 2017.07-armbian (Jul 18 2017 - 16:01:02 +0100) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi Zero Plus DRAM: 512 MiB MMC: SUNXI SD/MMC: 0, SUNXI SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial…

Hello all. Trying to get PCIe/NVMe working (even to show on microSD boot, let alone boot NVMe) on a custom compile on my Orange Pi 5 SBC version 1.3.2, because the official images aren't working either for me. No idea where to go from here and need some assistance as NVMe is required for my purpose. Here is what I did during compile.sh > Show kernel config > Board: orangepi5 > Kernel: current > Target: jammy > Image with desktop > Gnome desktop > Base configuration > Tick: Browsers > Device Drivers > PCI support > (default values) > Device Drivers > NVME Support > (default values) I used "SHARE_LO…

Hello i successful compile kernel for my chinese tablet and work but usb host no work. # modprobe g_ether modprobe: ERROR: could not insert 'g_ether': No such device I use this configuration in kernel: https://pastebin.com/gWJWtRav i use base image cubieboard 1 legacy, script.bin for A13-SOM and uboot from archlinux uboot-a13-olinuxino-2017.01-2-armv7h.pkg.tar.xz .. Work: Wifi Realtek RTL8188CUS Nand read/write sdcard Audio jack 3.5 No tested/No know: LCD no can test at broken. Touch Guddix GT811 how to test? HYM8563S Real Time Clock (I2C). how to test? MMA7660FC 1.5 g 3-Axis Accelerometer (I2C…

I just got a copy of the dev branch armbian comipled (2017-04-10). I'm here with the grand goal of getting libsurvive running with the HTC Vive on the Orange Pi. In order to do this, I need to coax the OrangePi to output to the vive. I was skeptical at first, but it appears you guys support 4k@30, so it should be okay on the pixel-clock front. The vive is 2160x1200@90Hz. You can't underclock it. Just won't go then. It's sadly the only mode the thing supports. I've seen shreds and bits here and there of information about how to do this, but, it seems that most of it is out-of-date for the "dev" branch. Any hints on how I can get the OrangePi to output as per …

Hi all, I'm using armbian on a cubietruck for various purposes. One of them is HAM radio. BUt I just noticed we don't have support for AX25. In fact, we're missing all HAM-related stuff, so I think it isn't possible to build just the modules: # CONFIG_HAMRADIO is not set What I would need is this: CONFIG_HAMRADIO=y # # Packet Radio protocols # CONFIG_AX25=m # # AX.25 network device drivers # CONFIG_MKISS=m # uname -a Linux cubie.acasa.local 4.3.3-sunxi #3 SMP Mon Dec 28 11:27:16 CET 2015 armv7l GNU/Linux Thanks for your support. Marius

Why does Armbian include both include ifupdown AND NetworkManager by default? I'm not aware of anything that ifupdown can do that NM cannot and ifupdown doesn't have a TUI/GUI like NM so as far as I'm concerned ifupdown is just clutter that causes config clashes and boot delays. Isn't it time to strip ifupdown from Armbian? On a related note, I've never got any of the (ifupdown) network config options in armbian-config to work.

Since update to 5.5.0 kernel (-rc2) my Orange PI often freezed after uptime of several hours up to 3 days (usually less than 24 hours). Since downgrade to 5.4.10 it seems to be stable again (1 day for now, so I still keep my fingers crossed). (Before upgrade to 5.5. it was up for several weeks - and I don't remember any unplanned reboot). Unfortunately I have no logs (it logs to ram), but in one case if was connected via ssh and had "htop" running - it showed nothing special at freeze time (CPU temperature around 50°C, no high load (around 0,5 load avg, only one CPU cure with a CPU % > 50% (still < 80%)). When I noticed the frozen system, I n…

U-boot is always a great source of amusement, did anyone try that combination? Just yesterday got v2018.05 in, and it just does not work. I don't get any serial from u-boot SPL, do I don't know what is happening. I compiled it with #define DEBUG, and still no serial output at all. At last I downloaded latest mainline u-boot (v2018.07-rc2) from github, applied manually the patches, complied and it worked. It seems something very specific for v2018.05 and rockchip/rk3288

I tried to build the espressobin u-boot only with the command given in the docs: ./compile.sh 'compile_uboot' But I get ... COPY u-boot.bin CFGCHK u-boot.cfg rm: missing operand Try 'rm --help' for more information. [ o.k. ] Building flash-image-DDR3-512m_1cs_0-600_600.bin cp: cannot stat 'build/a3700/debug/flash-image.bin': No such file or directory [ o.k. ] Building flash-image-DDR3-512m_2cs_0-600_600.bin cp: cannot stat 'build/a3700/debug/flash-image.bin': No such file or directory ... Do I need more/different parameters or a different config-default.conf ? Sorry for these maybe stupid questions, I am aware that I don't really see through …

Hello, FYI for prospective on Odroid XU4, testing images for XU4 (I also have a Cloushell (mini NAS including LCD display)) desktop image link folder Ubuntu 14.04.1 : ok, upgrade to 14.04.3 ok, upgrade to kernel 3.10.92 ok, upgrade to odroid final kernel 4.2.0 DEAD Ubuntu 15.04 : DEAD after reboot (kernel 4.2.0) It seems the image with kernel 4.2.0 just removed "journal" feature of ext4 on startup, so at next reboot, the ext4 fs is dead. trying to fix the SD card on a amd86 Ubuntu gives error like "/usr/sbin" dead, filesystem is garbage server image link ubuntu server image is not usable, dead after first reboot (kernel 4.2 ?) archlinux image…

I've done an experimental build of 5.0.y for my NanoPiK2. It seems that most of the current rejected patches are simply not needed anymore. The only thing I'm not sure what to do is in patch 0038-media-meson-add-v4l2-m2m-video-decoder-driver.patch. I've comment out this line since it seems that v4l2 API has changed : // .vidioc_cropcap = vdec_cropcap, If some of you are more familiar, please, give some help here. Should I proceed to the commits ?

I know most of you probably don't want to hear any more about this chip, but I recently fixed quite a few long standing issues. It's not perfect yet, but it improves scanning/reliable reconnect, incoming frames missed in powersave, ping times, and rate selection. Here's the patch set: https://github.com/fifteenhex/xradio/pull/12 Edit: rebased from karabek: https://github.com/dbeinder/xradio/commits/karabek_rebase And some important comments about powersave: https://github.com/fifteenhex/xradio/pull/11#issuecomment-616226880 In short, relative to the current version, with powersave on, idle consumption is lower by 200mW, but with powersave off, it is 300mW hig…

I have built an image for BananaPi M3 using build and docker. I can install fine on 16GB cards, but anything larger is failing on the mmcblk0 partition resize and then is going into repeated fsck's and failed boots. I have built armbian debian stretch years before and had it installing and running fine on the BananaPi M3, on 256GB uSD Cards. I tried manually extending the partition from an imaged smaller one running parted followed by resize2fs and it had the same crashing on boot. The boots a bit too fast to ascertain where its crashing but it might be the uDev step. Can anyone offer any help with this

I would like to build a hard realtime Linux kernel for Orange Pi SoC. Using Xenomai technologies (Installing Xenomai 3.x , Xenomai Documentation). This would be a great extension of the SoC application area. I did this for the x86 architecture. And I've already assembled the core using your Arabian technology. But building the realtime Xenomai kernel requires pre-patching from a third-party project Adeos (Adaptive Domain Environment for Operating Systems). Patch files for different architectures can be found here: Index of /downloads/ipipe/v4.x Is it possible to build a realtime kernel using Arabian? P.S. I apologize for my poor …

Mainline dev image as here: https://forum.armbian.com/index.php/topic/3574-orangepi-2-wifi-driver-issue-in-mainline-dev-410/ When I try to run armbianmonitor: rufik@opi2:~$ sudo armbianmonitor -m Stop monitoring using [ctrl]-[c] Time CPU load %cpu %sys %usr %nice %io %irq CPU/usr/bin/armbianmonitor: line 271: /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq: No such file or directory 12:57:09: MHz 0.02 1% 0% 0% 0% 0% 0% 38.5°C^C So it looks like cpufreq not working. Dmesg says: rufik@opi2:~$ dmesg -T | grep -i cpu [Wed Feb 15 21:40:37 2017] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=50c5387d [Wed Feb 15 21:40:37 2017]…

Hello, I try build kernel for NanopiNeo board with user kernel patch, but I don't understand with path needed put my patch. In previous version armbian's builds I just put files to userpatches/kernel/sunxi-current how it described in docs. But now with current version Armbian build system it's not working. I put my custom linux-sunxi-current.config to userpatches folder, my patch to userpatches/kernel/sunxi-current and try build kernel with command: ./compile.sh BOARD=nanopineo BRANCH=current kernel I see that linux-sunxi-current.config found and applied but not patch isn't.

Hello everyone, I am new to this forum. Apologize if this has been asked before, but I couldn't find it. I do docker run -it -P --privileged lib /root/compile.sh I get the following towards the end of the build process Fetched 68.1 MB in 60s (1,130 kB/s) Reading package lists... Reading package lists... Building dependency tree... Reading state information... hostapd is already the newest version (2:2.6-4~armbian5.34.171017+1). The following NEW packages will be installed: sunxi-tools 0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded. Need to get 36.9 kB of archives. After this operation, 134 kB of additional disk …

There is another topic with answer for desktop case. But how to rotate the console screen, when there is no desktop? The suggestion about change in kernel parameter - fbcon=rotate:<number> didn't work for me (edited boot.cmd, compiled with mkimage command, and I see boot.scr changed ) and I was unable to change the /sys/class/graphics/fbcon/rotate file - it stays unchanged.

I am going to use your Banana Pi image for my media server image release. I would like to know how to re-enable the regenerate ssh keys and resize the SD card on first boot (I want the password to stay the same).

Hi there, I am trying to build the image using docker, but I get several "Segmentation fault (core dumped)" error messages and as result the build gets interrupted. Would like to stick to docker build (I am running of fedora 39, and it automatically selects docker), as it looks to be far more efficient rather than running it into a VM. Any idea on how could I get rid of this issue? Thanks is advance! Andrea

I would love to see a guide on how to create a virtual machine for Armbian which would be great for testing in VMWare Workstation, Player or Virtualbox. It would be similar to the diet pi vm which autoboots into the qemu (I think) for the Raspberry Pi If someone has a rough guide on how to do it I can make something noob friendly. My guess is you need to install qemu, add some repositories and then get it to autoboot using rc.local or something like that. Any resources on how to get started would be much appreciated.

Hi all, I tried to build the kernel on my Ubuntu 15.10 machines which uses gcc 5.2 as default compiler. As mentioned in other threads this did not work. I found out two possible solutions. Apply the following kernel patch Compile the kernel with option -std=gnu98. I therefore changed the kernel makefile. --- a/arch/arm/kernel/return_address.c +++ b/arch/arm/kernel/return_address.c @@ -63,11 +63,6 @@ void *return_address(unsigned int level) #warning "TODO: return_address should use unwind tables" #endif -void *return_address(unsigned int level) -{ - return NULL; -} - #endif /* if defined(CONFIG_FRAME_POINTER) && !defined(CONFIG_ARM_UNWIND) / else…

I was doing some testing and it looks latest u-boot is broken for Allwinner H3 (no boot), A20 (Banana no network), I assume A10 too. There was some RFC upstream, but I did not go further into details ... Shall we rather rollback to 2017.03?

Dear Community, I'll build a Developer Team specially for Banana Pi Boards!" GPIO Libarys I started updating/modifing the old GPIO-Libarys, so they can be used on the latest builds! I want to build a Team, for GPIO-Libary Development, for porting these Libarys: WiringPi-Node WiringPi-PHP WiringPi-Perl WirinigPi-Ruby gpiozero rpi-gpio Updating and modifying these: RPi.GPIO BPI-WiringPi2-Python BPI-WiringPi2 At the end, all currently working GPIO Libarys are: luma.oled RPi.GPIO BPI-WiringPi BPI-WiringPi2 B…

I've done a build Meson64-DEV with 5.2.y ... I will commit the switch as soon as runtime test succeded !

I recently started getting these errors constantly... not sure what's going on. I can ping the address just fine, and even if I modify the lib config sources file to change it to ftp.us.debian.org, I still seem to run into the same errors. Any suggestions on what might be causing the problem? [ error ] Installation failed Failed to fetch http://httpredir.debian.org/debian/pool/main/libn/libnl/libnl1_1.1-7+b1_armhf.deb Could not resolve 'httpredir.debian.org'​ Thanks.

Hello together, I'm developing a device driver for a network interface controller for MOST bus. So, first of all, I've added a node with all the settings for this IC in my DTS, the IC is connected to second I²C-controller: &i2c2 { pinctrl-names = "default"; pinctrl-0 = <&i2c2_pins_a>; status = "okay"; os8104: os8104@41 { compatible = "smsc,os8104"; reg = <0x41>; master = <0>; /* slave mode*/ bypass = <0>; /* /ABY (all bypass mode) im register bXCR */ reset_gpios = <&pio 8 17>; /* PI17 */ int_g…

Hello Everyone, Does anyone know, which script contain the mounting part in the repo? I would like to mount my HDD as it's mounted in the ubuntu trusty desktop version. I'm using debian wheezy(legacy kernel) Thanks, Sp0T

Hi, I have a board Orange Pi Zero with modified PAs for power of WiFi module from PA20 to PA02, by soldering a connection on board. This is done to allow connection of I2C DAC. I see that board definition in 'u-boot/configs/orangepi_zero_defconfig' It uses dts definition of: 'arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts' I need to modify one section of this dts file from: reg_vcc_wifi: reg_vcc_wifi { compatible = "regulator-fixed"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; regulator-name = "vcc-wifi"; enable-active-high; gpi…

clone the latest armbian/build repo, run ./compile.sh but fail. I try native or docker build, all fail.

Hi All, Can someone tell me how to update the script.bin in sd card and nand. I am using a custom board, which has different usb pin config. So Im trying enable it in script.bin. This is what I done so far. For SD card 1. I delete /boot/script.bin 2. Write new config in /boot/script.bin 3. Reboot Then the usb is still not detected, it seems that I did something wrong. For nand: 1. I boot via sd card 2. mount /dev/nanda /mnt/nanda 3. rm /mnt/nanda/script.bin 4. cp new_script.bin /mnt/nanda/script.bin 5. umount /mnt/nanda 6. reboot Again, nothing happens. The usb is still not detected Thanks in advance.

Armbian provides its own hostapd. Why? This is relevant because of the recent WPA2 bug. Upstream hostapd has been patched: https://packages.debian.org/jessie/hostapd I don't understand the precise relation between Debian and Armbian. Will this patch percolate down? Thanks

Hi, I attempted to build armbian for orange pi 5 with these steps (I'm on macos): multipass delete armbian-build multipass purge multipass launch -n armbian-build --disk 50G --mem 8G --cpus 4 multipass shell armbian-build sudo apt install curl build-essential bc bison flex libssl-dev chrpath cmake cpio wget xz-utils curl -LO https://github.com/armbian/build/archive/refs/tags/v25.5.0-trunk.67.tar.gz curl -LO https://github.com/armbian/build/archive/refs/tags/v25.5.0-trunk.32.tar.gz tar -xzvf v25.5.0-trunk.67.tar.gz cd build-25.5.0-trunk.67 ./compile.sh (select edge version for orange pi 5 in the cli) CTRL+D multipass transfer armbian-build:/home/ubuntu/build…

Hi all, I'm doing experiments with WiFi monitor mode on AP6212(bcm43430)-based boards with nexmon (driver/fw patching framework for wifi monitor mode). I tried it on OPi Zero Plus 2 (Kernel 4.14) and it works pretty much "out of the box", but sometime crashes. I'm still investigating about it, since the same fw+driver work flawlessy on RPi Is there anyone else who played around with it?

Dear Armbian community, I'm trying to make a minimal size Armbian image ( Ubuntu 16.04 with default kernel). Build system works great, but when I'm building the system without GUI (Image wit console interface "server") a bluetooth system doesn't work. I tried to build same system with same configs, but set "Image with desktop environment". In this case bluetooth system works great. I tried to solve this problem by myself, but..... It seems like I can not fix it. So, why I'm thinking that bluetooth system doesn't work. When I'm using bluetoothctl list it is void output. hciconfig -a void output I tried to start systemctl st…

Good afternoon dear gurus. help to transfer please system with sdcard to sata hdd in OrangePI +2. Debian jessy and additional software is established. what needs to be made? if it is possible, then on steps. the point is that I want to refuse completely loading with sdcard and emmc. To be loaded only with sata hdd. Thanks in advance.

Hi Wondering if anyone knew the algorithm that assigns mac addresses to orange zero. Is it based on something static/cpu id /...? or it is purely random. Will this mac change over time or after it is generated, it will stay the same? I have one zero that mac is pretty static and another changed mac after I did a upgrade. If I want better control of the mac address, what's the best way to make it static? this is on the mainline -jerry

Hi all, please be aware that Pine folks in the meantime understood that recommendations to use WinDisk32Imager, dd and other non verifying burning tools are wrong, tried to recommend Etcher instead (as usual sabotaged by at least their most famous forum moderator) and now use finally a 'branded' Etcher 2.0 beta: https://forum.pine64.org/showthread.php?tid=4481&pid=27520#pid27520 I don't think it's correct to do it this way (and at least the macOS application sucks since not digitally signed and using a wrong so called 'bundle identifier') but anyway. Let's take this for a foresight. Etcher 2.0 uses catalog files in such a way: http:…

Hi guys I cloned the build earlier with a view to building an image for a rpi5b git clone --depth 1 --branch main https://github.com/armbian/build and build/config/boards/rpi5b.csc was present. I've just refreshed the clone and it's not there - has it been removed for some reason ? Edit It's not on github either - am I going mad ? 🙂

I tried to used AppArmor under the Linux cubietruck 4.4.1-sunxi #10 SMP Wed Feb 17 17:57:20 CET 2016 armv7l GNU/Linux. But I get a kernel panic after i rebooted the system. Some questions: 1. Did you integrate AppArmor into the kernel? 2. Did you use an alternative mandatory access control? 3. Need I an additional kernel argument in the /boot/boot.cmd other than these "apparmor=1 security=apparmor"? 4. Is there a major diffenrece between your kernel and that from danad.de? Unluckily I was not capable of getting a dump from the kernel panic. If you need it, I would take a photo.

Hi, Where should I place a .patch in order to be taken into account on a next custom armbian built? This is for building legacy images. Need to have a modified nanopineo.fex and got a .patch for it, where should I place it in order to be applied on top of the armbian-provided one? P.S. Seen this -> https://docs.armbian.com/Developer-Guide_User-Configurations/ but it only mentions u-boot and kernel.

Hello guys, hope I'm in the right subforum. If not, please postpone. I have a question about the device tree and pinctrl... I have added a chip to my I2C-0, the configuration looks like this: &i2c0 { clock-frequency = <400000>; status = "okay"; os8104: os8104@41 { compatible = "smsc,os8104"; reg = <0x41>; master = <0>; /* slave mode*/ bypass = <0>; /* /ABY (all bypass mode) im register bXCR */ pinctrl-names = "default"; pinctrl-0 = <&os8104_reset &os8104_int &os8104_aint &os8104_error &os8104_3dB>; }; }; Then, under pinctrl I have added this b…

I've struggled the whole day on that task using v2019.01 ... It is even worst than my struggling back in early December, even using Method #2 give me headache with Pinctrl not initialize and boot device been garbage : channel 0 training pass! channel 1 training pass! change freq to 800MHz 1,0 ch 0 ddrconfig = 0x101, ddrsize = 0x20 ch 1 ddrconfig = 0x101, ddrsize = 0x20 pmugrf_os_reg[2] = 0x3281F281, stride = 0x9 OUT U-Boot SPL board init Pinctrl init failed: -19 Trying to boot from m�iYk~Ⱥ�C��+J)H�^J!������wZ��q�+����q����!

Found an old (2015) Ugoos UT3+ / UT3 Plus with an rk3288 - the neat thing about this board is it has HDMI-IN ! Also has PIP Specs: I'm was eventually able to successfully screen capture @ 1920 x 1080 ~29 fps using the Android 5.1.1 firmware V3.0.7 for UT3+ https://mega.nz/#!cQpl0ICS!8EgHddI3_PXQsSe-TSrkHfxdHCmkbckNWBYuLhfuA7w The firmware crashes frequently and the painful part is the IR remote is required to start recording.. so I'll be porting gentoo / armbian to this device to turn this paper weight into a linux friendly screen capture device. It maybe …

Just a minor problem: uptime from procps-nf 3.3.15 (Armbian buster) - as used in 30-armbian-sysinfo to get uptime/logged-in users/load - generates different outputs if the uptime is either less or more than 1 day or less than 1 hour ("hh:mm" or "d days, hh:mm" or "nn min") - this gets the 30-armbian-sysinfo confused on gathering the logged-in user count resp. load. I suggest the below fix: ... # get uptime, logged in users and load # fix for uptime from procps-ng 3.3.15: reports uptime less then a day as "hh:mm," # but uptime larger than a day as "nn days, hh:mm," or "nn days, mm min", and less than 1 hour as "mm min," # which mixes up the assig…

I have build armbians img for orangepi pc2 and prime. No 5.41 debian stretch both + XFCE4. I compressed it to tar.gz. Linux -*.deb and armbian-*.deb. How can I upload it to your server?

I am trying to create my own USB gadget based on sunxi_usb_udc and GadgetFS with Orange Pi PC. I can't find any details about sunxi_usb_udc and after successful startup and detection, I am unable to get data sent by host side. How can I proceed?

Hello all, I wrote up this documentation mostly as notes to myself about how I successfully built a kernel and ubuntu core rootfs. If you could let me know how to improve it, please let me know. I don't generally write documentation. I focused on the roc-rk3328-cc but it should work okay for a variety of the Firefly chips. Thanks, ~Ben barebone_to_ubunutu.md

Hello, In december, it was possible to install 4.19 kernel for Rock64. Unfortunately this kernel was removed from Armbian repo. 4.20 kernel is bogus, USB doesn't work and SD card is very slow. 4.19 was fine. Is it possible to make it available again in in the repo ? Thank you

Hi I have a nanopi-m1 board and connected a simple dc motor to GPIO15(pin10). I used this commands to run the mtor but nothing happend else making a folder named gpio15 in /sys/class/gpio path! echo 15 > /sys/class/gpio/export echo out > /sys/class/gpio/gpio15/direction echo 1 > /sys/class/gpio/gpio15/value Also I tried it with GPIO18 (pin12) and didn't work!

We are starting a HW design for a board that will probably be using RK3328. We want this board to be running Armbian. We need to select BT and Wifi chips. Would like to use chips that are already supported by Armbian. Is there a list of Bluetooth and Wifi chips that Armbian supports? Any recommendations?

Please take a look on CPU usage precision on the new kernel for x64 and arm64. It is 1 milliseconds. But kernel 6.13 on armv7 still provides 4 milliseconds of precision. How do I tune CPU usage precision on image build?

Hello, everybody I have a task to make "easy install image" to orange pi pc2. I build already Armbian_5.46_Orangepipc2_Ubuntu_xenial_next_4.14.47_desctop.img and its actualy what i need and now I need to make it "easy install" - becouse we have a lot of SD card to burning. Could you recommend me, how to: 1. Scip first boot user creation. (Armbian on the first boot ask to set the new root password and create new user). Can i preinstalled this information? I need that Armbian on first boot just load without some user inputs. 2. Add my program to start up. I have a A ) zip with my program and B ) bash script which unzip program and set it lunch on s…

Hi. According to this patch Orange pi 5 Pro DTS (which BTW i use for my successful Orange Pi 5 Pro edge build) there will be a split of DTSI files. Most of the code in rk3588s-orangepi-5.dtsi will be transferred to new rk3588s-orangepi-5-5b.dtsi. In my current build for Orange Pi 5 and 5 Pro I have: rk3588s-orangepi-5-5b.dtsi rk3588s-orangepi-5b.dts rk3588s-orangepi-5.dts rk3588s-orangepi-5.dtsi rk3588s-orangepi-5-pro.dts. Please note I have Orange Pi 5 Pro with SPI chip soldered on so for Orange Pi 5 Pro build with EMMC (99.99% of cases) in rk3588s-orangepi-5-pro.dts set: /* SFC */ &sfc { status = "disabled"; }; and &sdhci { …

I'm currently working on the meson64 family (C2, K2, Le Potato) as a family, and am trying to more or less make their GPIO behaviors similar and matching (as best I can) to the RPi they are form factor clones of. An issue I'm having right now has to do with the spidev driver, these boards don't have hardware spi where the Pi/Tinker does does, so I'm defining spi-gpio devices in the device tree. That part is fine. Where it gets interesting is setting up a spidev node under it. - Calling out a compatible = "spidev" works, enumerates, etc, but throws the typical ugly error during boot that it is wrong to do it that way. - Adding a compatible string to the…

Hi, I own a Orange PI One and I wanted to create a compile environment in a virtualbox as I did not find any available. So I followed the instructions found here: http://www.armbian.com/using-armbian-tools/ 1) downloaded "ubuntu-14.04.4-server-amd64.iso" 2) create a new virtual box image (ubuntu 64bit) 3) Execute the following command: apt-get -y -qq install git git clone --depth 1 https://github.com/igorpecovnik/lib cp lib/compile.sh . sudo ./compile.sh The process end with the following lines: [ o.k. ] Building deb [ linux-u-boot-orangepih3-5.07-armhf.deb ] [ error ] ERROR in function compilte_uboot [ common.sh:155 ] [ error ] Building u-b…

I'm using banana pi M1 plus and armbian legacy kernel. I wanted to use uart0(ttyS0), uart2(ttyS1) and uart3(ttyS2), so I tested those three uarts with an echo server in banana pi and a program sending a data in a PC. When I tested uart2 and uart3, I was able to get the data that I had sent without any problem. For the uart0, however, there was some error messages. I was also able to get the data, but I want to deal with the error message so that I can prevent any future problem. It seems that the error is caused because the ttyS0 is sending some console messages. I've found some articles about getting rid of console output from ttyS0. Most of them said to modify …

Hello! I'm trying to build xunlong kernel from https://github.com/orangepi-xunlong/linux-orangepi/tree/orange-pi-5.10-rk3399. I see a .dts file for OrangePi 4 ... but no suitable defconfig or any description what defconfig to use. What I'm doing wrong?

Hi all, I'd like to compile latest kernel 4.11-rc7, so i added KERNELTAG="v4.11-rc7" to ./compile.sh and created file /userpatches/lib.config and added KERNELBRANCH="4.11" to it i also added to /lib/configuration.sh according to documentation ARMBIAN_MAINLINE_KERNEL_VERSION='4.11' # lock in a particular kernel version but i get this error : [ o.k. ] Using user configuration override [ userpatches/lib.config ] [ o.k. ] Syncing clock [ host ] [ o.k. ] Downloading sources [ o.k. ] Checking git sources [ u-boot v2017.03 ] [ .... ] Up to date [ error ] ERROR in function fetch_from_repo [ general.sh:184 ] [ error ] Error in configuration [ o.k. ] Pr…

Hi, Anyone here ever tried to build a mainline uboot for sunxi-3.4 kernel. As mentioned here v2015.10 support NAND spl. https://linux-sunxi.org/Mainline_U-Boot#v2015.10 I'm in the first part of doing it, but unfortunately I'm always stuck with this error. OBJCOPY examples/standalone/hello_world.srec OBJCOPY examples/standalone/hello_world.bin LDS u-boot.lds LD u-boot DTC arch/arm/dts/sun7i-a20-ainol-aw1.dtb In file included from arch/arm/dts/sun7i-a20-ainol-aw1.dts:10:0: arch/arm/dts/sun7i-a20.dtsi:47:54: fatal error: dt-bindings/interrupt-controller/arm-gic.h: No such file or directory #include <dt-bindings/interrupt-control…

Hello, I noticed that the official armbian images for this board(s) are based on Jessie -> https://www.armbian.com/odroid-hc1/ NCP only supports Stretch, but that is ok, because I build the armbian images from source. The Odroid XU4/HC1/HC2 NCP images I build ( https://ownyourbits.com/downloads ) are using Stretch and everything seems to be working fine so far. My question is, what is your testing procedure to consider an image stable? Would it help if I built the plain Armbian image as well so it can be shared in https://www.armbian.com/odroid-hc1 ? I would be happy to help with this Apologies if this has been asked bef…

What do we have? Serial connection: Hardware schematics: orangepi-plus-h3-v1_1.pdf Wireless: Realtek RTL 8189 ETV Allwinner introduced new way of storing board definitions (also on A23 and A80) so it's a bit different than on A20 boards. H3_Manual_build_howto Kernel building with Allwinner SDK is terrible and was not able to build it. I must admit I haven't invest much time and energy yet.

I've added new patches for OrangePi-ZeroPlus and commited them. Like for OPiPrime done yesterday, the OrangePi-ZeroPlus WiFi still not working. I don't know why yet, although is more encouraging than OPiPrime, since at least the driver comes up in "lsmod" in the OrangePi-ZeroPlus, while for the Prime it didn't. Also another issue : OrangePi-ZeroPlus has an eMMC, I was able to do "nand-install-sata", but I'm unable to boot from it, although the MMC2 DT is part of U-Boot, for some reasons, it doesn't scan it.

Hi igor Can you build and add libcsptr to your repo? ( https://github.com/Snaipe/libcsptr ) it is required by libvdpau. i tried to build it via the build environment but it doesn't work ;-) :-( vdr_sunxi-vdpau (){ git clone https://github.com/Snaipe/libcsptr.git $DEST/cache/sdcard/usr/local/src/libcsptr chroot $DEST/cache/sdcard /bin/bash -c "cd /usr/local/src/libcsptr && mkdir build && cd build && cmake -DCMAKE_INSTALL_PREFIX=/usr/local .. && make && make install" chroot $DEST/cache/sdcard /bin/bash -c "cd /usr/local/src/libcsptr && make" chroot $DEST/cache/sdcard /bin/bash -c "cd /usr/local/src/libcsptr &am…

i worked on the BPI M1 Board (the first one) for quite a while now improving or more or less rewriting the A20 CSI camera driver. there are no more artifact-ghost-frames any more. The framerate goes from 5fps(full) to 120fps(crobbed small) i also modified the camera-device driver for the ov5640. disadvantage: existing camera device drivers would not be compatible any more. maybe someone wants to give it a try and check it out. it can be found here: https://github.com/xenpac/OV5640-Sunxi-A20