Allwinner sunxi

Hello everyone! I have Banana Pi and installed Ubuntu desktop Xenial 4.9.12. I have a USB wifi stick and Ubuntu recognizes , and USB works well. The problem is when I try to set my Banana Pi as an access point, then we Ubuntu reported to have root privileges. How to get root privileges in Ubuntu Xfce graphical environment? How to stop autologin before lifting graphic Xfce desktop, and to ask for the root password? Please help, and thank you in advance

Armbian Cubietruck Desktop does not start the graphical environment for Nand. I downloaded the Armbian Legacy 5:10 Cubietruck Debian jessie 3.4.112 Desktop (http://mirror.igorpecovnik.com/Armbian_5.10_Cubietruck_Debian_jessie_3.4.112_desktop.7z) , I recorded the image on an SD card using a software called Rufus ( https://rufus.akeo.ie/ ) Insert the card into Cubietruck and Armbian starts and works perfectly ! Nand-sata-install.sh run the script to perform the copy of the card to nand , the same copy without any error and asks at the end off the Cubietruck and disconnect the SD card . After disconnecting the SD card the Armbian does not start. However I rode the…

hi i have problem with orangepi plus2e i have not image on hdmi i atach some logs from Tera Term (serial terminal) witout sd HELLO! BOOT0 is starting! boot0 version : 4.2.0 boot0 commit : c8c201b51b7ea1baa94590a1887313124d9a5879 fel_flag = 0x00000000 rtc[0] value = 0x00000000 rtc[1] value = 0x00000000 rtc[2] value = 0x00000000 rtc[3] value = 0x00000000 rtc[4] value = 0x00000000 rtc[5] value = 0x00000000 rtc[6] value = 0x00000000 rtc[7] value = 0x00000000 DRAM DRIVE INFO: V1.4 the chip id is 0x00000081 the chip id is 0x00000081 the chip id is 0x00000081 the chip id is 0x00000081 the chip id is 0x00000081 NOT…

I have an orange pi zero that I'm going to use as a pi hole. When installing pi hole, I received a "Error: Unable to update package cache. Please try "sudo apt update"." I did just that and received another error stating Err:1 https://ports.ubuntu.com focal InRelease Could not connect to ports.ubuntu.com:443 (2620:2d:4000:1::19). - connect (111: Connection refused) Could not connect to ports.ubuntu.com:443 (185.125.190.39). - connect (111: Connection refused) Could not connect to ports.ubuntu.com:443 (2620:2d:4000:1::16). - connect (111: Connection refused) Could not connect to ports.ubuntu.com:443 (185.125.190.36). - connect (111: Connection refused) Er…

Hello all, The board has a 2MB NOR FLASH chip what would be enough for storing u-boot and booting the system over network. Unfortunately u-boot says there is no ethernet. Is there anybody who knows how to enable ethernet on this or similar board like OPi PC2 or Nanopi NEO2? Is it just a matter of configuration or is RTL8211E as PHY generally not supported on H5 chips? Thank you very much for your help. --DieHackbeere

Here my changes over the script.fex file to achieve compatibility with the 15.6FHD LCD display [disp_init] disp_init_enable = 1 disp_mode = 0 screen0_output_type = 1 screen0_output_mode = 4 screen1_output_type = 0 screen1_output_mode = 4 fb0_width = 1920 fb0_height = 1080 fb0_framebuffer_num = 2 fb0_format = 10 fb0_pixel_sequence = 0 fb0_scaler_mode_enable = 1 fb1_width = 1024 fb1_height = 600 fb1_framebuffer_num = 2 fb1_format = 10 fb1_pixel_sequence = 0 fb1_scaler_mode_enable = 0 lcd0_backlight = 0 lcd1_backlight = 197 lcd0_bright = 50 lcd0_contrast = 50 lcd0_saturation = 57 lcd0_hue = 50 lcd1_bright = 239 lcd1_contrast = 50 lcd1_saturation = 57 lcd1_hue = 50 [lcd0…

Upgraded kernel on existing working project and g_ether no longer working. So did fresh install on formatted card of Armbian_5.75_Orangepizeroplus2-h5_Ubuntu_bionic_next_4.19.20 If I do modprobe g_ether and then dmesg, I get the following udc-core: couldn't find an available UDC - added [g_ether] to list of pending drivers Is there something new in 4.19.20 that I must do? It used to work in older releases from 9 months ago or so...

Hi Igor and all, after running armbian on my A20 lime2 for a long time, I decided to switch to armbian on my A10 lime, too (from jessie with a eewiki-based self-compiled kernel). So far it works as perfect as the A20, but there are two small and funny things with the Armbian_5.00_Lime-a10_Debian_jessie_3.4.110.zip image I used: After login the nice armbian banner stated that my A10 lime is a cubieboard . I have a cubieboard, too. So I double checked... The problem is located in /etc/init.d/armhwinfo, There all "sun4i" boards are simply "Cubieboard". I had to adapt the LED check which is used to detect Lime and Lime2 a bit and added the Lime A10. I ch…

I just installed the latest Ubuntu Bionic Image with 4.x kernel, fully updated and upgraded. On Orange Pi Zero 1.4 512MB + IO expansion kit board Armbian 5.75 Ubuntu 18.04.2 LTS Linux orangepizero 4.19.20-sunxi #5.75 SMP Sat Feb 9 19:02:47 CET 2019 armv7l armv7l armv7l GNU/Linux `cat /proc/asound/cards` "No sound cards" In armbian-config, I enabled analog-codec, `update-initramfs, rebooted, but there's still no sound card. mocp complains there is no driver. speaker-test (starts like this) Playback device is default Stream parameters are 48000Hz, S16_LE, 1 channels Using 16 octaves of pink noise ALSA lib conf…

hello Igor, I get some error information after updating the new kernel v4.1 root@cubie:~/3.4.108# dpkg -i linux-image*.deb (Reading database ... 70156 files and directories currently installed.) Unpacking linux-image-cubietruck (from linux-image-cubietruck_4.1_armhf.deb) ... dpkg: error processing linux-image-cubietruck_4.1_armhf.deb (--install): trying to overwrite '/lib/modules/3.4.108-cubietruck/modules.builtin.bin', which is also in package linux-image-3.4.108-cubietruck 4.0 dpkg-deb: error: subprocess paste was killed by signal (Broken pipe) Errors were encountered while processing: linux-image-cubietruck_4.1_armhf.deb how to solve this. Best regards Fla…

Hi gurus! I'm trying to connect gc2035 camera to my OrangePi One, it's marked as SH-2035 at the cable. It is old problem, as I understand reading forum, but nothing to help me. I'm new Linux user and use Armbian 5.31, Linux orangepione 3.4.113-sun8i #18 SMP PREEMPT Thu Jun 15 02:16:06 CEST 2017 armv7l armv7l armv7l GNU/Linux. That camera works with Armbian 5.20, but I don't want to do downgrade. As I understand it needs to do right initialisation of camera in script.bin or rc.local, but what exactly?? This is part of configuration in my script.fex file: [csi0] vip_used = 1 vip_mode = 0 vip_dev_qty = 1 vip_define_sensor_list = 0 …

Hey, I am using the Image from the Armbian Download site: Armbian_20.11.6_Bananapim2zero_bullseye_current_5.10.4 and I am trying to get SPI to work, enabled it using armbian-config and through editing the /boot/armbianEnv.txt verbosity=1 bootlogo=false console=both disp_mode=1920x1080p60 overlay_prefix=sun8i-h3 rootdev=UUID=034edbda-9395-4820-87a1-f3a83bad8a58 rootfstype=ext4 overlays=spi-spidev usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u But after a reboot it does not show in /dev/ (what seems odd, i2c-0 shows in /dev/ even though it is not enabled in the armbianEnv.txt) As far as I understand it, the …

First : i downloaded both Armbian versions for "Orange Pi+ 2" but reported link file names where different from those that actually download : a) link says https://dl.armbian.com/orangepiplus/Ubuntu_xenial_default_desktop.7z, but download file is Armbian_5.38_Orangepiplus_Ubuntu_xenial_default_3.4.113_desktop.7z b) 2nd link says https://dl.armbian.com/orangepiplus/Debian_stretch_next.7z, but download is Armbian_5.38_Orangepiplus_Debian_stretch_next_4.14.14.7z Second : after download i extracted both with : 7z e filename.7z then i run etcher 1.4.4 cli : ./etcher -d /dev/sdd filename.img -y , result sdcard writed, then i inser…

Hi, I have a problem with the wifi connection of the Orange Pi Lite when I connect a HDMI device and switch it on. It is not possible to get the wifi working. I have the same auth. error message like many others here too. But the wifi works well without HDMI device or when the device is off. I have tested the last debian and ubuntu server version and mainline. Thanks for helping

Hi, Lime2 A20 not even detecting mini usb ethernet, which was working perfectly fine on 3.xx. Manfu: Netgear USB: USB 2.0 Ethernet Adapter P/N: 322-10167-01 dmesg doesn't even list the device. Could board's port be damaged? I tired usb port with usb ethernet, it lists as: I'm using arbmian Ubuntu 18.04 with beta packages. Thanks

Hi, For long (long) time I did not update my nano pi duo image, recently I changed microSD card and wanted start fresh with latest image. I have tried latest debian image and also tried building image for the BOARD target as `nanopiduo`, but in in both cases my board is stuck at ... U-Boot SPL 2024.01-armbian-2024.01-S866c-P7738-Ha5c2-Va723-Bb703-R448a (Mar 09 2025 - 03:54:39 +0000) DRAM: 128 MiB Trying to boot from MMC1 ns16550_serial serial@1c28000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19 U-Boot …

Hi, I try to play with Armbian Stretch mainline kernel 4.14.y on Orange Pi Zero and need for my idea sf funktion (SPI) and i2c in u-boot terminal. I've build mainline U-Boot but the files in /boot directory from armbian looks so "strange". There is any description how to replace the files or make changes. Thanks for help. P.S. Have a lot of experience with uC programming, less with Linux.

Hello all, i wonder what is the status of the support for this touchcontroller. I've got to know that in latest kernels there is prebuilt support for it and in my latest armbian there is a module for this. But following this: https://www.raspberrypi.org/forums/viewtopic.php?t=143581 i failed to make it work. May be i've done it the wrong way in armbianEnv.txt tho. Should i just insert theese line into this file? dtparam=i2c_arm=on dtparam=spi=on dtoverlay=ads7846,penirq=25,speed=10000,penirq_pull=2,xohms=150 According to dmesg log, module is loading, but nothing happens when i touch the screen. If not, should i instead us…

Hi, I'm running a kernel from yesterday on Orange PI One Plus: Linux orangepioneplus 5.5.13-sunxi64 #trunk.087 SMP Fri Mar 27 01:33:22 CET 2020 aarch64 GNU/Linux I've sucessfully setup wireguard: root@orangepioneplus:~# wg interface: wg0 public key: YKbQlQmch4sfNOtymDrnZbuLTD3zLO72cbIIFuXED1c= private key: (hidden) listening port: 42655 peer: dg1cKCId81d6h5cWUQ61BMHksBbi0FdFnitjxDuOuno= endpoint: ******:51820 allowed ips: 10.9.0.0/24, fd86:ea04:1115::/64 latest handshake: 15 seconds ago transfer: 92 B received, 180 B sent persistent keepalive: every 25 seconds But it seems that crypto is failing from time to time: root@orange…

Hello all, I am very excited to install armbian debian jessie on my cubietruck ! I managed to get the Armbian_5.31_Cubietruck_Debian_jessie_next_4.11.5.img to an SD card, plugged it in, switched it on and everything went perfectly fine! Great! Now, I am trying to get this OS on the CT Nand. Sadly, the nand-sata-install doesn't work, returning the message : "There are no targets. Please check your drives". One very strange thing to me is the output of the /proc/partitions files that shows the following : major minor #blocks name 1 0 4096 ram0 1 1 4096 ram1 1 2 4096 ram2 …

hi, I have an OPI pc with armbian (legacy kernel), plan to set it as NAS. due to it has 4 USB ports without internal hub, so I decide to connect 3 USB HDD to it, and create a LVM+RAID5. but unfortunately, OPI pc can only recognize 2 USB HDD(any 2 of these 3 USB hdd), at any USB ports, the 3rd USB HDD can be found by lsusb but stops at "spinning up...." no /dev/sdc. but if I insert an USB disk, (with 2 USB HDD already inserted), it can be recognized and /dev/sdc is created. I guess whether there is a power supply issue. can this be fixed by USB HDD with additional power supply? is that right?

Hi, how can I enable hardware decode of video h264 mpeg on H5 chip? I use a Orange pi pc2 but video goes slow and lag very much. H5 SoC has very value hardware but isn’t possibile use mali GPU yet? Thanks

Is someone tried to instal Kodi and is it work?

Hello! Anybody help me, please.. How to set up HDMI to connect monitor? How to make it reboot normally on "shutdown -r now"? Kind regards, Ellad

Hi all, I trying many days set up temperature sensor work, but no luck ( Orange PI PC Armbian 20.11.3 Focal with Linux 5.9.14-sunxi try many pins, 3 and 5 V , but same result, no sensor read. No any resistor, 1 sensor armbianenv: overlays=w1-gpio usbhost0 param_w1_pin=PD14 param_w1_pin_int_pullup=1 output: root@orangepipc:~# gpio readall +------+-----+----------+------+---+OrangePiH3+---+------+----------+-----+------+ | GPIO | wPi | Name | Mode | V | Physical | V | Mode | Name | wPi | GPIO | +------+-----+----------+------+---+----++----+---+------+----------+-----+------+ | | | 3.3V | | | 1 …

Getting FDT_NOT_FOUND(spi-add-cs1) and FDT_BADMAGIC(spi-dev-1) on uboot.

Orange Pi Plus 2e How do I clone the SD card and both have boot capability? I am new to the concepts of Pi's so I am looking to slowly add abilities to the pi and have a working clone which I can use when I stuff it up. I have also seen no mention of grub being used anywhere. My main computer is a amd 64 with Debian running but I can use my laptop with win 8.1 on it but would prefer a solution which I can use on Debian Thanks for your help Dave

Tried both Debian and Ubuntu based 23.5 releases on my v1.4 board Boot process stops at "Starting kernel..." Also tried the "minimal CLI" debian release with same results. The previous versions 23.02 are fine. ▒ U-Boot SPL 2022.07-armbian (May 27 2023 - 19:26:49 +0000) DRAM: 512 MiB Trying to boot from MMC1 U-Boot 2022.07-armbian (May 27 2023 - 19:26:49 +0000) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi Zero DRAM: 512 MiB Core: 65 devices, 17 uclasses, devicetree: separate WDT: Not starting watchdog@1c20ca0 MMC: mmc@1c0f000: 0, mmc@1c10000: 1 Loading Environment from FAT... Unable to use mmc 0:1.…

I want to use an ADAU1979 with an olimex A20-Micro. Needs to show up as a device in ALSA, alongside the in- built CODEC - As far as I can see, this driver is in mainline kernel but I have no idea how to configure the kernel build to include it. Obviously we need to tell the system where its i2s/SPI interface is connected etc. Unsure which kernel version (legacy or mainline) to begin with. We do need a desktop environment and the olimex 10"/7" LCD to work also... I am starting this from a position not having built a kernel or kernel modules before so If this idea is a non-starter, someone please tell me so. Thanks.

Hello Team, I am worked on Olimex Lime2 rev.G2 board but now olimex start delivering Rev.K board. I used the same Armbian Rev 5.35 image which is having kernel version (4.13.16-sunxi) & u-boot version v2017.09. On Rev.G2 Ethernet speed was as expected but in rev.K it is not working. By default board booted and comes with ethernet speed 100Mbps, but in this case Ethernet is not working (DHCP server unable to assign ipv4 address to eth0). Later i reduce the eth0 speed to 10Mbps it start working as expected but spped is 10Mbps Some more info about the ethernet issue which will help to understand the issue more clearly - …

Hi to All, I recently upgraded my "test server" to the current version, by flashing a new image to my sd-card. However i forgot to recover some essential files, before flashing! I liked very much the login info about the the number of available updates, since I used the testing repo at that time. Could someone provide the code snipplet for that piece of info ann thell me, in which file to place it?? Well, many many thanks for your help and advice! regards, ireng

My board works pretty well upto 1 000 00 Hz without fan and up to 1 200 000 Hz with (noctua) fan. However I am still using an usb wifi card, to be able to connect with ssh. Anyone having wifi with the built in wifi card work properly? Mine just shuts off. With an external wifi usb card, it works like a charm. Since my 3-d printers are in the living room I i have the orange pi:s in the living room. They are primary used for octoprint. I would like to have the built in wifi on orangepi prime to work.

Hi, I've got a quick question regarding the kernel upgrade instructions on a Cubietruck that runs on Igor's Debian image. Let me mention first that the system boots from my Cubietruck's NAND. However, the root partition and the /home partition are both installed on some SSD. I've followed the instructions about the kernel upgrade (3.4.106-cubieboard to 3.19.6-cubietruck) in order to be able to use the proper shutdown feature - as detailed on http://www.igorpecovnik.com/2013/12/24/cubietruck-debian-wheezy-sd-card-image/. I.e. I installed the various *.deb packages which were contained in the *.tar archive via `dpkg -i`. Then I ran the steps as desc…

Hi everyone, I'm trying to set up transmission daemon + some webserver who can play some video or let smart tv watching some video or listening music, any idea? Thank you very much

Which is the correct overlay to specify for libcamera support for the Arducam IMX219? I am assuming this would go into /boot/armbianEnv.txt ? The packages libcamera0.3 libcamera-tools libcamera-v4l2 installed properly, however, all examples on the net apply to PIs and not the OrangePiZero... Thanks in advance.

Hi all, First of all, I must congratulate the Armbian team for such an amazing job! It is really terrific! I'm using Armbian on a NanoPi Neo where I'm running an application that relies on having low latency UART responses. My application is having a latency of around 10ms and I believe that it might be related to the tick rate defined in the Armbian kernel (http://www.makelinux.net/books/lkd2/ch10lev1sec2). I would like to increase the tick rate, however, I got a little lost when I tried to browse the Armbian repository. I couldn't find the actual Linux Kernel source code. In order to increase the tick rate I need to edit the file /include/asm-"ar…

Hello , I first time to use not do anything just to apt-get update but get this message ! This image may have problem . Thank !

Hi all Given that the node that H3 consumption uses to change DRAM frequency no longer exists on H5 on the mainline kernel, how would one go about altering this?

I have bought 3 OPi Lite 2 (H6 based) dev boards. Just downloaded the latest Bionic image at the following link: https://www.armbian.com/orange-pi-lite-2/ I understand it's WIP. However, it seems to have issue on booting up. I connected HDMI cable and upon boot up, I could see init info on the screen, then it says, starting Kernel ... , then screen goes no signal, power LED stays RED forever. I read that the current image seems to have issue on HDMI. But it worked with HDMI upon initial bootup, then stopped working. My problem is that without HDMI, how could I edit the WIFI config to have the board connected to my network thus to SSH into the board for fu…

Hi, I'm here to dig into low power consumption with allwinner H6 boards, I own an OrangePi one plus and I'm already doing some tests. With an H3 board and legacy kernel I would simply tweak fex file to turn off the unnecessary, and there is already good material around this argument. But with mainline kernel there is no documentation about lowering power consumption. I would really appreciate some hints on how to tweak down consumption for H6 boards and mainline kernel, probably editing DT overlay or some other config/patch files, and re-building? I already tweaked the simplest things like: -Using fast ethernet instead of gigabit -Lowering max CPU frequency (…

Help! I used your overlay, but nothing works for me. Orange pi zero 3 (Armbian Linux 6.12.35-current-sunxi64) overlay: /dts-v1/; /plugin/; / { compatible = "allwinner,sun50i-h616"; fragment@0 { target = <&spi1>; __overlay__ { status = "okay"; cs-gpios = <&pio 7 5 0>,<&pio 2 15 0>; /*PH5=CS0 for lcd, PC15=CS1 for touch*/ display: display@0 { compatible = "ilitek,ili9341"; reg = <0>; pinctrl-names = "default"; spi-max-frequency = <20000000>; rotate = <270>; bgr = <0>…

I was sort of disappointed with my RPi 2 VPN performance, which is about 2.5MiB/s while normal traffic can easily exceeds 5.5MiB/s. So I setup same VPN config on OPi One and run the test. The speed is impressive which is well above 5 MiB/s but it could only last about 10s before the box reboots itself. I can see one cpu core is occupied 100% by softirqd ( about 80% on RPi 2). My kernel version is 3.4.112 and StrongSwan version is 5.3.3. Don't have further information yet. When I get a chance to hook up serial console, I may collect more info.

Hi, I have a BananaPi and BananaPi Pro connected to the Lemaker 7" TouchLCD. When I boot the system, I can't see any console output. I only see a flashing cursor in the left top corner and then it starts the X-window-manager. What do I have to change to see the boot messags on my LVDS LCD? I have tried to change the console=both value to tty0 or tty1 via armbian-config, but this doesn't work. Any ideas? Here is the output from cat /proc/cmdline: root=UUID=e9635572-227e-485c-b76d-b4f0d6d34394 rootwait rootfstype=ext4 console=tty1 console=ttyS0,115200 hdmi.audio=EDID:0 disp.screen0_output_mode=1920…

I had success with @ubobrov's sunxi-cedar-mainline driver before on H3 devices. I'm trying to get it to work on the Orange Pi 3 LTS (H6) however it keeps giving the following error: sunxi-cedar 1c0e000.video-engine: syscon failed... Any help would be much appreciated. dmesg: [ 6.167614] cedar_ve: loading out-of-tree module taints kernel. [ 6.167700] cedar_ve: module verification failed: signature and/or required key missing - tainting kernel [ 6.168445] sunxi cedar version 0.1 [ 6.168601] [cedar]: install start!!! [ 6.168654] cedar_ve: cedar-ve the get irq is 23 [ 6.168673] sunxi-cedar 1c0e000.video-engine: assign…

Hi, I've bought Orange Pi Prime from the second hand. I've also bought 5V 3A power supply. It it was booting with Debian and Armbian. I was using Kingston SDHC cards. Suddenly my board stopped booting from mmc card. I also tried to boot it from Sandisk A1 class card but with no success. Do ypu think it is hardware malfunction or something else?

Hi, i have an orangepi zero 2w and tried noble gnome image with the "current" kernel (v6.6.x). I activated the gpu via armbian-config and reboot. Then it stucks somewhere in the booting process. It shows nothing on the screen. If i use the orange pi image instead, i can activate the gpu with orangepi-config, which is a similar tool like armbian-config. The gpu works fine then and has great performance. So it's theoretically possible. Can someone explain to me what the problem is here. If it was a simple port, it would surely have already been done. I tried also the dtb from the orange pi image, but then it also didnt boot up. Th…

I was installing real time clock on Orange Pi One board ... , after some unsuccessful tries I found that the battery has bad solder and all is fine now date was set "up" and "down" ... from Sat Jan 1 02:06:23 EET 2000 to Thu Jul 8 21:37:42 EEST 2032 several times ... and during all this time armbianmonitor was running (I did not check it every time ... I made many reboots ) now armbianmonitor shows some "static" data , in which the time is always 0:18.50 ... and I am thinking that may be it is showing the "last" recorded , I mean the higher date/time ...which is somewhere in the future 2032... I try reinstalling armbianmonitor ... did not helped how to remove …

Hi, i have a Olimex Olinuxino-micro-emmc and the armbian image 5.31 and 5.25 booting fine but NO network is comming up. The link led's are on but no once Packet will be transmitted. The same board with my own u-boot/kernel version has no problems with network device. is it a bug or a feature? Best regards Mike

Hi! Banana pi m1, armbian Ubuntu Xenial Legacy 3.4.113, bluetooth usb dongle. I can find bananapi from other devices, but can`t pair whit any device. journalctl -u bluetooth ar 15 16:05:11 bananapi systemd[1]: Starting Bluetooth service... Mar 15 16:05:11 bananapi bluetoothd[646]: Bluetooth daemon 5.37 Mar 15 16:05:11 bananapi bluetoothd[646]: Starting SDP server Mar 15 16:05:11 bananapi systemd[1]: Started Bluetooth service. Mar 15 16:05:11 bananapi bluetoothd[646]: Bluetooth management interface 1.0 initialized Mar 15 16:05:11 bananapi bluetoothd[646]: Failed to obtain handles for "Service Changed" characteristic Mar 15 16:05:11 bananapi bluetoothd[646]: Not e…

hi, i've been trying to get the SC16IS752/I2C UARTs working on opi-zero using DT Overlays. Here is my .dts: /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h2", "allwinner,sun8i-h3"; fragment@0 { target = <&i2c0>; __overlay__ { #address-cells = <1>; #size-cells = <0>; status = "okay"; sc16is752: sc16is752@4D { compatible = "nxp,sc16is752"; reg = <0x4D>; clocks = <&sc16is752_clk>; interrupt-parent = <&pio&…

Hello, I am trying to use g_serial but it does not work. I'm using fresh install of armbian (Armbian_5.38_Orangepilite_Debian_stretch_next_4.14.14.7z), with apt-get update/apt-get upgrade/armbianconfig Install headers. Linux orangepilite 4.14.15-sunxi #28 SMP Mon Jan 29 07:24:48 CET 2018 armv7l GNU/Linux This is the overlay I use to enable OTG: sudo /usr/sbin/armbian-add-overlay usbotg.dts /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { target = <&usb_otg>; __overlay__ { dr_mode = "otg"; status = "okay"; }; }; }; After rebooting OPi there are several erro…

I've been happily running orangepipc with armbian (buster, 4.19.62-sunxi) as an openvpn gateway for my home devices for some time. Here are some details: I have a remote openvpn server the pi runs an openvpn client and connects to the server the pi has ipv4 packets forwarding enabled my wifi router provides the pi's ip as the default gateway via dhcp So when I connect to wifi with my phone, all phone traffic will be routed through the remote openvpn server without need to install the openvpn client on the phone itself. With this setup the pi can easily saturate my 30mbit cable connection when downloading torrents for e…

Hello Guys, I want to use airodump-ng (Aircrack-ng Suite) or Kismet to get all WiFi Clients in the area. For that, I would like to use the internal WiFi Chipset (so I don't have to use an external WiFi Dongle). My problem is, after I enable the monitor mode (with iwconfig and/or airmon-ng), which gives me no error and it says, the monitor mode is enabled, I am getting no results with Airodump-ng nor Kismet. Are there any solutions for this problem? Is is the driver not capeable of using monitor mode? Thanks in advance, KittFanNr1

I run Armbian 20.02.1 stable on a zeropi which is used as a wireguard server and spotify direct client (USB to external DAC). Things run very well. Many thanks to everyone involved in keeping Armbian such a great distro! I noticed that when I turn on the ondemand governor the system becomes very unresponsive and music playback is stuttering. When I use the performance governor (even with min and max frequency both set to 480MHz) things run just fine. Most of the time 480MHz will be sufficient, but it would be nice to be able to take advantage of the ondemand governor. Any help is greatly appreciated.

Hello, I configured 2 armbian on sd card and the configuration of the i2c is the same in armbianEnv.txt. Plattform Olimex-Lime2 A20 verbosity=1 logo=disabled console=both disp_mode=1280x1024p50 overlay_prefix=sun7i-a20 rootdev=UUID=194e9f9a-826b-4644-9f2f-4ef388277816 rootfstype=ext4 overlays=i2c1 i2c2 uart3 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u as you see, I confiugred the overlays. But on one image I get: #image with desktop sudo i2cdetect -l i2c-3 i2c mv64xxx_i2c adapter I2C adapter i2c-1 i2c mv64xxx_i2c adapter I2C adapter i2c-2 i2c …

I am running ubuntu xenial (legacy version) on my orangepi zero 256Mb version and using it as a web server with light torrenting. The SoC temperature reading in armbianmonitor reaches above 80C easily. When i log in via ssh after boot the temperature reads usually 60-65 C and normal operations easily cross 70C. This is my first SBC so I am not sure if this is normal? Can anyone tell me if these temperature readings are notmal or do i need heatsink to cool down my system? Thanks in advance.

So I enabled overlays=usbhost0 in armbianEnv.txt it works after reboot. I connected my OTG converter and connected my bluetooth and managed to see the bluetooth device. However, after rebooting / powercycle, i notice '[ 23.700998] musb_bus_suspend 2584: trying to suspend as a_wait_bcon while active' appearing non-stop in dmesg How to get this message is as follows 1) Switch off your device. 2) Connect your OTG microusb to usb converter (You may / maynot plug in your usb device to it) 3) Switch on your device. 4) Run dmesg and it runs crazy. However, if you power on WITHOUT connecting your OTG co…

Hi, as many did, I've bought a (CSI) OV5647 camera from AliExpress and am struggling to get it to work. Been at it for a week now and am at a loss. So i'm trying to get some clarification via this thread on how to get this camera to work. What I've done so far is to compile a mainline kernel (Ubuntu Bionic) and edited the kernel config file to include sun6i_csi and ov5647 driver. Build finishes successfully and am able to boot and load the drivers Unfortunately the OV5647 isn't recognized and /dev/video0 isn't created. Second build included a userpatch I've found online which i applied to no avail to the kernel https…

After along time I downloaded a new armbian image, after doing apt update/upgrade for the last year or so. I was quite surprised to see that the pcduino3nano is now deprecated, while other A20 boards are still supported. What was the exact reason that the pcduino3nano was dropped from support? If I keep using the deprecated OS, can I fully use apt update/upgrade for all user stuff? What would happen to all kernel and u-boot update packages? Is the latest armbian for the pcduino3nano automatically disabling those updates, or do I need to do something manually? *should* I block kernel & u-boot updates? thanks, Michale Jasson

Hi I trying to return in work OPi+2e board but faced some odd thing. When I trying to boot Armbian I getting temperatures about 180C which leads to shutdown during booting. It reproduceable with all versions from hirsute/5.12.15 back to oldest avaliable bionic/5.4.8 Official Ubuntu xenial/5.3.5 works fine, but /sys/class/thermal/thermal_zone0/temp gives negative readings (like about -76500) Installed on eMMC old RetrOrangePi which is Armbian jessie/3.4.113 also works but gives zero (exactly 0) temp reading. Finger test gives "room temperature" reading and "warm" while old OS works. Definetly not 180C Board itself is from 2017, worked a…

Hi there, I want to use my NanoPi in a Walloutlet to controll my Sonos system. My Problem at the moment is that the Nano PI gets really hot (65° Celsius). At the moment i only got a Raspberry Pi Cooling set(http://www.conrad.ch/ce/de/product/1267831/Kuehlungs-Kit-Raspberry-Pi-A-B-B-Cubieboard-Banana-Pi). Is there a way to get the Board to get to 45° Celsius with no fan? Thanks for the Project, good to see that someone works on these devices to keep them Supported with the newest stuff. Greetings from Switzerland Twosky2000

just curious if there's a quick way to manipulate an existing Armbian build to have separate /boot and / partitions on my SD card, without needing to setup an Ubuntu build environment to compile everything myself. It's really the only thing I'd want to change about the pre-built image, and would like to avoid setting up the Ubuntu build box if I can. Thanks!

I am compiling the armbian for orangePi3, using the armbian tools ... and the compilation works fine. It works both from the kernel_only and from the entire image But I have a problem with the current version of the kernel, because it turns out that it does not support the hdmi-vga adapter and I would like to compile the 5.07 kernel instead of the 5.10. I have found in the doc but I do not find how to indicate to the compile.sh script that it has to compile version 5.07 of the kernel. Inside the file config-default.conf I do not see where to put the version. The documentation: https://docs.armbian.com/Developer-Guide_Build-Preparation/ It is insuffic…

BACKGROUND: Back on June 27th, I posted my questions regarding my wish to have certain kernel features activated (or not) by default in the Armbian/Debian kernels of the time -- specifically since I wanted to activate 'PPS' features in order to build a Stratum 1 GPS/PPS timeserver: Kernel Option Requests? Here are the 'old' instructions that I used back in June: ORANGE PI PLUS H3 with GPS/PPS I ended up needing to install VirtualBox with an Ubuntu 16.04 environment, and successfully created what I needed (i.e. 3.4.113-PPS-sun8i). I was also eager to create a much newer kernel, but that failed (i.e. 4.11.5). My Orange Pi PC…

I'm trying to test I2S Audio playback. I've mounted a Windows network share like so: //apps/MUSIC /mnt/music cifs noserverino,iocharset=utf8,username=media,password= 0 0 And playing with: aplay -D default:CARD=sunxisndi2s /mnt/music/test.wav With this result: underrun!!! (at least 2.218 ms long) Any ideas?

Hi friends, I am trying to downclock my OPi Zero and set/disable unused cores 1,2,3, limit DRAM speed, limit max cpu core frequency, put voltage down. Is this possible on Opi Zero? I tried e.g. but when I cat /sys/devices/system/cpu/cpu3/online is is always 1. Any idea please? Some advice how to do all of this is highly appreciated. I am trying to downclock Opi Zero to push produced heat down.

Hi guys orangepi-one and i'm trying to install the Super Nintendo Classic Controller wich is i2c bus /---------\ | | | 1-2-3 | | 4-5-6 | | _____ | \_/ \_/ ``` | Controller Pin | Function | Pi Pin | |---------------:|---------------|-----------| | 1 | I2C data | 3 (SDA) | | 2 | device detect | - | | 3 | +3.3V | 1 (+3.3V) | | 4 | GND | 6 (GND) | | 5 | not connected | - | | 6 | I2C clock | 5 (SCL) | i have wired the controller to the orangepi bus port 0 and port 2 i found a driver fo…

Hi, I am looking to Secure Boot Allwinner H3. We use Nano Pi Duo2 with latest Armbian OS. End goal is to have all the OS / Data on the SD Card Encrypted. Can anybody help ?

Hi everybody! We have an application that uses RS-485 and we decided to use the OMAP UART implementation, but it doesn't seems to work with Cubieboard A10. We tried to enable in userspace, by calling ioctl and also via dts file. ioctl (C code): ------------------------ ... if (ioctl (fd, TIOCGRS485, &rs485conf) < 0) { printf("Error: TIOCGRS485 ioctl not supported.\n"); } /* Enable RS-485 mode: */ rs485conf.flags |= SER_RS485_ENABLED; /* Set rts/txen delay before send, if needed: (in microseconds) */ rs485conf.delay_rts_before_send = 0; /* Set rts/txen delay after send, if needed: (in microseconds) */ rs485conf.delay_rts_after_send = 0; if (ioct…

I recently received my kit, which consists of the Neo, heatsink, and acrylic shell. Installed Debian_jessie_default.7z with Etcher onto a Kingston SDCIT/8GBSP. PCB 1.3+ uses a more sophisticated voltage regulator than earlier revisions... The temperature is excellent so far (only 40c). I can run some more tests if someone provides instructions. So these boards do not in fact require a heavy copper plane for heat dissipation. I did use a superior heat pad rather than the one that is provided with the heatsink kit. Ideally, you would want something like a 4mm or so copper shim with good quality thermal paste applied to bo…

I've been using the Armbian R1 image (Armbian_20.02.1_Nanopi-r1_buster_current_5.4.20.7z) on the NanoPi R1S with good success. In particular, the USB host port worked perfectly, with no changes required. I thought it was probably about time to upgrade to a newer kernel, so I downloaded Armbian_21.02.1_Nanopi-r1_focal_current_5.10.12.img, flashed it to an SD card, and booted. However, plugging in an external USB device results in absolutely zero shoing up in `dmesg -w`. I tried a USB-UART (STM32-based ACM), USB3 hub, USB 3 Mass Storage (Kingston 16GB), and a Playstation 3 Eye, without any entries in dmesg. To do some debugging, I also downloaded Arm…

Hi guys, i've the following problem in my attempt to customize/study armbian: - succesfully compiled Armbian_5.17_Bananapim2_Debian_jessie_4.8.0 on Ubuntu 16.04 with default config; - burned image on SD card, (on the same card burned with Armbian_5.14_Bananapim2_Debian_jessie_4.6.2_desktop and the system boot is ok) - the board enter in this reset loop: U-Boot 2016.07-armbian (Sep 11 2016 - 10:06:05 +0200) Allwinner Technology CPU: Allwinner A31s (SUN6I) Model: Sinovoip BPI-M2 DRAM: 1 GiB MMC: SUNXI SD/MMC: 0 *** Warning - bad CRC, using default environment HDMI connected: Setting up a 1680x1050 dvi console (overscan 0x0) In: serial Out: vga Err: vga…

I'm trying to install mpd and I'm getting an older version than I'd expect. I'm expecting 0.19, but getting 0.16. I've done the apt-get update. Am I missing something?

hi there, i was setup linux-wheezy-root-cubietruck 4.2 on cubietruck nand.these days i upgrade system it show me a error message: Unpacking replacement linux-wheezy-root-cubietruck ... dpkg: error processing /var/cache/apt/archives/linux-wheezy-root-cubietruck_4.70_armhf.deb (--install): unable to make backup link of `./boot/bin/lime.bin' before installing new version: Operation not permitted Errors were encountered while processing: /var/cache/apt/archives/linux-wheezy-root-cubietruck_4.70_armhf.deb i thik this is a bug because dear developer don't think about when system install to nand later some problem. how to fix? thanks!! 估计用CT的很多是…

I Attached ili9341 but i ran the command confbmap 2 8 and then ctrl + alt + f2 the lcd was showing to enter password i did but now i see this never goes into gui any fix?

Hi, I have just received some shiny new NanoPi Neo 2 boards, hardware v 1.1, model 1711 with 1Gb RAM. I have installed Armbian Stretch mainline kernel 4.19.y with no issues at all however I have noticed that the green LED is pretty well ignoring anything I ask of it. ls -la /sys/class/leds/ total 0 drwxr-xr-x 2 root root 0 Jan 25 16:14 . drwxr-xr-x 52 root root 0 Jan 1 1970 .. lrwxrwxrwx 1 root root 0 Jan 1 1970 nanopi:green:status -> ../../devices/platform/leds/leds/nanopi:green:status lrwxrwxrwx 1 root root 0 Jan 1 1970 nanopi:red:pwr -> ../../devices/platform/leds/leds/nanopi:red:pwr cat /sys/class/leds/…

Hi all, I'm trying to understand how to make an infrared tx/rx module working. This is the module: https://www.aliexpress.com/item/5V-IR-Infrared-Remote-Decoder-Encoding-Transmitter-Receiver-Wireless-Module/32528109291.html Is there a way to make this works in userspace? Overlays? From the docs I was only able to understand how to enable existing overlays. I enabled cir, this is from my armbianEnv.txt: overlays=cir i2c0 but I don't know how to configure pins: which is rx which tx. Do I need to write down a new/custom overlay? I think that configuring pins is crucial to enable IR communication at some level but …

I found that it is not easy to use the Dallas one-wire temperature sensors and the composite TV-Out on the Banana Pi with the current Armbian version. I have searched for posts on these topics in the forum. The posts that I have found in this forum describe solutions for outdated Armbian versions or do not give enough detail. The following posts in this thread will describe how to solve these problems for the current Armbian version for the Banana Pi M1.

I have root partition on SATA drive (/dev/sda1). I tried to use vanilla kernel, but it doesn't boot and even doesn't show HDMI output (I set root=/dev/sda1 in boot.cmd and recompiled boot.scr of course). But the legacy kernel with the same configuration works. Any suggestions why?

Hello all, I recently got an orange pi pc plus, and am going to try to use it as a server. However, I do not want it to boot into the desktop GUI as this wastes precious computational resources. How do I force the Pi to boot into the terminal? I am using armbian in order to have the system boot off of the EMMC flash memory. Thanks.

Hello, With wheezy and I can't use CB2 build in /dev/ttyUSB0. cannot access /dev/ttyUSB0: No such file or directory What should I do to enable it and use it?

I am trying to get composite video fully working on an Orange Pi Zero Plus 2. I installed the legacy kernel image, and I've been able to turn on composite out, but I just get a blank screen on boot and there is no /dev/fb0. Is there anything else I have to do to enable the framebuffer. This is the (I believe) relevant portions of the script.fex file: [boot_disp] advert_disp = 0 auto_hpd = 1 output_type = 4 hdmi_channel = 0 hdmi_mode = 4 cvbs_channel = 1 cvbs_mode = 11 output_full = 1 hdmi_mode_check = 1 [disp_init] disp_init = 1 disp_mode = 1 screen0_output_type = 3 screen0_output_mode = 5 screen1_output_type = 2 s…

Hi, I am having an issue with my system running a nanopi Air. After boot, my system won't detect my rtc (i2cdetect doesn't show it) nor my USB device. The problem must come from my SD card or is software related. Indeed, when I am booting from another SDcard, with aembian installed, everything is detected normally. Does anyone has a clue? Thank you, Tibibs

Hey, I am currently trying to get sending IR commands from my CubieTruck working. I am using Igors Armbian_4.2_Cubietruck_Debian_jessie_3.4.108 image. But it seems like the modules are not initialised in a way that they also can send since irsend returns errors that this device does not support sending. I tried it with the hardware.conf from the image aswell as with the hardware.conf and init.d file from https://github.com/matzrh/sunxi-lirc/wiki. Apparently, I have to do "echo $GPIO-Number > /sys/class/lirc_gpio/tx_gpio_pin" which I did with the right pin so in theory, the driver should be set up the way it is supposed to be. Yet still irsend throws errors. Ca…

hi all, i need add extra ethernet card for my cubietruck A20 I have lindy based on Manufacturer: ASIX Elec. Corp I have read this topic but i did not understand all. in my cubie when attach the card in dmesg have : [ 722.103004] usb 4-1: new high-speed USB device number 6 using sw-ehci [ 782.958675] ehci_irq: port change detect lsusb Bus 004 Device 007: ID 0b95:1790 ASIX Electronics Corp. in another pc with when attach the card [21892.375550] usb 3-1.2: New USB device found, idVendor=0b95, idProduct=1790 [21892.375557] usb 3-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [21892.375560] usb 3-1.2: Product: AX88179 [21892.375563] usb 3-1.2: Ma…

I made this simple dts file for my GPS NTP server running on Zero2/3 and Zero2w On Zero2, use PC9 as PPS in , and on Zero2W use PI5 . It should be configured in /boot/armbianEnv.txt, but I unsuccess on zero2w, so you must comment out two lines and compile it by yourself. Maybe help someone. sun50i-h616-pps-gpio.dtso

Hello everyone, Please beg my pardon if the question might seem “stupid†but I searched quite a bit without finding a solution. I’m using the ARMBIAN version of Debian Jessie on my Banana Pro with a great dose of satisfaction and I have noticed that the message about “system status†which appears on the first SSH Login Screen after each reboot provides a very useful insight into my system. From my researches I think I have understood that this is called “MOTD†(message of the day) and it is supposed to appear only once per session. I would like to display this message every time I open a new SSH Connection windows to my device, so to always have that i…

Hello, I bought Orange PI PC and tried ubuntu mate but ended up deleting it because wifi was not working.After search i found this Armbian OS and its always updated.I have downloaded armbian for my orange pi pc. Extracted the file and I then used win32 disk image for write image on sd card.After succesfull write what i find is that the memory card becomes inaccesible from my windows 10 pc.Do i have to copy any additonal file like kernel script bin or uImage?because in ubuntu mate from orangepi forum i used to copy to ubuntu mate. When i plug that writed sd card to orangepi and connected to hdmi screen it gets started and booting.AFter it reaches to login so…

Hello fellas, I would like to borrow your experience to compete with my task which counts (and measures) pulses on GPIO with Orange Pi zero. Currently, my simple solution is to register a callback to a specific edge and increment a global variable. I would like to catch a few hundreds of pulses in one burst which have in a 5-100 us length. However, even the number of counted pulses is not okay. Some of them are missed sometimes, which leads to an unreliable solution. I used different libs and all of them fall into the same issue. I tried the following libs: * ArmbianIO (C) * ArmbianIO (Python: origina…

Hello, I love armbian and I know the gpio is working on the directory /sys/class/gpio/gpio(number) but I really need to use armbian + the gpio module gpio-sunxi modprobe gpio-sunxi ls /sys/class/gpio_sw/ normal_led PA10 PA13 PA18 PA20 PA6 PA9 PC2 PC7 PG7 PL10 PA0 PA11 PA14 PA19 PA21 PA7 PC0 PC3 PD14 PG8 standby_led PA1 PA12 PA15 PA2 PA3 PA8 PC1 PC4 PG6 PG9 echo 1 > /sys/class/gpio_sw/standby_led/data echo 0 > /sys/class/gpio_sw/standby_led/data is it possible to active this module with kernel 3 or 4, if yes where is possible to enable it ? in the …

New installed image: Armbian_5.14_Nanopim1_Ubuntu_xenial_3.4.112.raw [ 1321.621490] [cpu_freq] ERR:set cpu frequency to 240MHz failed! [ 1321.856382] [ARISC ERROR] :message process error [ 1321.874795] [ARISC ERROR] :message addr : f004b840 [ 1321.893322] [ARISC ERROR] :message state : 5 [ 1321.911038] [ARISC ERROR] :message attr : 2 [ 1321.928962] [ARISC ERROR] :message type : 30 [ 1321.946430] [ARISC ERROR] :message result : ff [ 1321.963905] [ARISC WARING] :callback not install

I've had success with Armbian runing on Orange Pi One and pcDuino2. I'm using the legacy kernels on these boards. Today I've got a pcDuino3B - similar to pcDuino3 except it has GB ethernet from the pcDuino3 nano. I tried legacy kernels for both the 3 and the 3 nano. I see high cpu load ~35% from one of the kworker processes. Then I tried the mainline kernels from the 3 and the 3 nano. No cpu load problems but the GbE does not appear to be configured in the 3 image. 3 nano works on both ethernet and wifi so I'm wondering whether to stick with this one and see if there are any other differences. I don't have a build environment set up and no experience with kernel debug…

A quick one... is there an estimated date on when a stable version (next version) will be released for OPI Zero...? I am looking for to have the following included: > Full H2+ support / would be great with the goal to to force the power consumption to the lower side > SPI boot from USB > Working serial gadget / Serial through OTG

Hi when I use the orangepi PC plus TRRS audio output (analog), I have some glitches which are linked to the video mouvment. I've tested the connection between ground and video and it seems that on the left ground pin there is a natural link with video output (50 ohms), is this normal? my cable is a 4 pole TRRS. I even tested audio with cable directly plug on soldering but same result. How could I get a clean audio output? note that the hdmi audio output is clean. and my speaker system is clean if I plug it on a MP3 player with an audio jack. I use retrorangepi 4.2 which is based upon Armbian v5.54 (default legacy kernel)

I'm looking for udev rules or some other way to read system LEDs without sudo. I tried https://github.com/todbot/blink1/blob/master/linux/51-blink1.rules, but I suspect it's not 100% what I need for the Duo.

I have Orange Pi PC connected via HDMI to a Samsung SyncMaster T220HD with 1680 x 1050 at 60 Hz. Currently Armibian defaults to 1280 x 1024 and edges are outside the screen. What can I do and which configuration I edit to get better results?

I switched armbian repo to stable via armbian-config 24.11.2. The first thing it did, judging by /var/log/apt/history.log, was purging linux-image*: Start-Date: 2025-01-04 22:47:25 Commandline: apt-get -o APT::Status-Fd=4 -o APT::Keep-Fds::=5 -o APT::Keep-Fds::=6 -y purge linux-image* Requested-By: user (1000) Purge: linux-image-current-sunxi64:arm64 (24.11.1) End-Date: 2025-01-04 22:47:27 Then it proceeded to purge and reinstall dtb and armbian-firmware, but not linux-image: Start-Date: 2025-01-04 22:48:34 Commandline: apt-get -o APT::Status-Fd=4 -o APT::Keep-Fds::=5 -o APT::Keep-Fds::=6 -y purge linux-dtb* Requested-By: user (1000) Purge: linux-dtb-cu…

How to Disable or Hidethe text that scrolls during boot armbian orange pi?? thanks for your reply!!

Hi, there are invalid references inside sun50i-h5-fixup.scr, I think. I use NANOPINEO2, myself compiled linux-*-current-sunxi64_20.05.0-trunk_arm64.deb, kernel 5.4.28-sunxi64 #trunk SMP PREEMPT. amrbianEnv.txt (reduced): overlay_prefix=sun50i-h5 overlays=i2c0 uart1 uart2 usbhost1 usbhost2 usbhost3 param_uart1_rtscts=1 param_uart2_rtscts=1 For example, the row param_uart2_rtscts=1 leads to use following rows of sun50i-h5-fixup.scr: fdt get value tmp_phandle1 /soc/pinctrl@1c20800/uart2 phandle fdt get value tmp_phandle2 /soc/pinctrl@1c20800/uart2_rts_cts phandle fd…

Hi I have added the serial monitor (because i had some trouble booting up) I can see the booting proces of the U-boot. If i'm looking in the log, i see a few file not found entry's: ** File not found /boot/.verbose ** ** File not found /boot/.next ** ** Unrecognized filesystem type ** ** File not found .next ** I did not see these files in the /boot directory either. Can i change something to get ride of these messages. Thx The complete startup log on OrangePi plus with armbian for orangepiplus: === U-Boot SPL 2016.03-armbian-sun8i (Apr 30 2016 - 23:26:36) DRAM: 1024 MiB Trying to boot from MMC U-Boot 2016.03-armbian-sun8i (Apr 30 2016 …