Allwinner sunxi

Hi, I am trying to install the aircrack-ng driver via dkms from over here: https://github.com/aircrack-ng/rtl8812au When I change the Makefile to match my processor arm-sun50iw1p1 , I receive these compilation errors and do not know how to fix them. cat /var/lib/dkms/rtl8812au/5.2.20.2/build/make.log DKMS make.log for rtl8812au-5.2.20.2 for kernel 4.19.20-sunxi64 (aarch64) Tue Feb 12 21:53:55 UTC 2019 make ARCH=arm64 CROSS_COMPILE=/home/android_sdk/Allwinner/a64/android-51/lichee/out/sun50iw1p1/android/common/buildroot/external-toolchain/bin/aarch64-linux-gnu- -C /lib/modules/4.19.20-sunxi64/build M=/var/lib/dkms/rtl8812au/5.2.20.2/build …

Hi there, Orange Pi PC+, Armbian Stretch. What I want is to replicate current router (OpenWRT Barrier Breaker on TP-LINK MR3220 v1) on and Orange Pi. I use this router to "share" (using scp from host PC) an USB flash dongle (remote site backup). With its processor copying filer over WiFi SCP is terribly slow (1.2MB/sec). Network Manager "proposes" me to create an WiFi network, but with only NO security or only WEP. I use WPA personal. Configuration on router wlan0 as an AP (WPA), wlan0-1 as WiFi client (also WPA different SSID) with WDS enabled (to act as bridge member), eth0 as usual. All those 3 interfaces bridged together an …

I'm using g_ether to connect OrangePiPc+ to network over USB OTG. On legacy kernel, that was giving 140 Mbits/sec IN (download from network to OrangePiPc+) and 170 Mbits/sec OUT. After upgrading to mainline kernel 4.19.62 (or 5.3.9), IN throughput degraded to 93-98 Mbits/sec (while OUT improved reaching up to 210 Mbits/sec in CDC EEM mode). This easily reproducible on both my boards OrangePiPc+ and OrangePiZero with latest Bionic images (clean installations + "modprobe g_ether iProduct="Linux-USB Ethernet/RNDIS Gadget" iManufacturer="Netchip Technology, Inc." dev_addr=02:81:05:F0:5C:24 host_addr=02:81:05:F0:5C:23 use_eem=0" ). Any ideas where is the bottleneck…

Hi, Armbian gurus, I'm trying to make the build system to build image with LibreELEC kernel tree for PineH64 I heard the kernel is patched for being better at hardware decoding Here are what I have done in order: 1. Retrieve patched kernel tree from LibreELEC build system. Upload the patched kernel tree to my gitlab account. 2. Modify config/sources/families/include/sunxi64_common.inc to make KERNEL_SOURCE = my previous repo; KERNELBRACH = master. To make it fetchable during bilding. 3. Modify lib/compilation-prepare.sh: skip aufs patch. 4. Modify lib/compilation.sh: skip advanced_patch in compile_kernel() After all th…

Hi , I just move my banana pi pro which was running bananian up to now to buster minimal. I'm using it as domoticz server. It requires few usb port to have all my gateway working. So I need to make USB OTG running in HOST mode. I did lot of testing, read many thread, but quite stuck right now. Here is what I have already done : First I have activated in DTB usb@1c13000 , and change mode to host. I have also activated usb0-vbus. I added also regulator-boot-on in usb0-bus. and last test I did is adding usb0_vbus-supply = < 0xb1 >; in phy@1c13400. For those who may need later on, here is the command I did: …

Hi, I am using Nanopi Neo board and I need RS485 driver to control DE pin automatically. I have prepared DTS Overlay file: /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { target = <&uart1>; __overlay__ { status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&uart1_pins &uart1_de_pin>; rs485-rts-gpios = <&gpio6 8 0>; /* PG8 active-low */ linux,rs485-enabled-at-boot-time; rs485-rts-delay = <0 300>; }; }; fragment@1 { tar…

Hi, i tried to use wlan0. I added an "ap6210" in /etc/modules. I added in /etc/network/interfaces auto wlan0 allow-hotplug wlan0 iface wlan0 inet dhcp wpa-ap-scan 1 wpa-scan-ssid 1 wpa-ssid mywlanssid wpa-psk andthepassword During loading i see two lines about ap6210 INFO Loading Module 6210 (or similarly) Fatal Module Ap6210 not found I wonder, how can I add the needed files? I am using this Image: http://www.igorpecovnik.com/2014/09/07/banana-pi-debian-sd-image/ Debian wheezy 4.1.2 In the discription is a hint, that everything should available. Many thanks in advanced for an hint. Im not very involved in linux. Regards, Ti…

hi all, I use cubietruck Linux 3.4.104-sunxi I would like to understand partition ramlog-tmpfs on /var/log type tmpfs (rw,relatime,size=524288k) in fstab is not present. I have the problem that it is always full, more than 90% My cubietruck it is install on nand, I would like to mount the partition of sd, how can I do? regards

Hi, I am running same distributed processes on my RaspberryPI Model 2B running Raspbian Jessie and two OrangePI PC's running Armbian 5.05. Though i have enough ram available i found that there is high SWAP utilization on my OrangePI PC's. Also one CPU will be always 100% in OrangePI PC's. I have swappiness = 1 for both OrangePI PC's and Raspberry PI. ulimit -l = unlimited for RaspBerryPi and ulimit -l = 64 for OrangePI PC's. Attached is the screenshot:- From left:- (1) RaspBerryPi. (2) OrangePi PC, (3) OrangePi PC. How can i limit the swap usage and high CPU for OrangePI PC? Regards, -- Avinash

Hello I want to do a special sdcard to my use of multiple card without reconfigure all the time. If I install into a 4gb sdcard after can I write a iso and copy to another sdcard and write to 128gb and when can I resize it into the new card? The minimum size of sdcard is 2gb or 4gb to do use desktop environment?

Hello I install alsa-utils and mpc , mpd but have hum from the speakers. And when try use alsamixer get sudo alsamixer cannot open mixer: Invalid argument I use jack-audio not hdmi

I'm running Armbian_5.20_Micro_Debian_jessie_3.4.112 on an Olimex A20 micro board. I find that opening serial port device `/dev/ttyS2` causes the system to crash. The board heartbeat LED either stops or blinks rapidly. The board itself is not pingable. I can reproduce this issue with a simple from the shell using: cat /dev/ttyS2 or from c code using: fd = open("/dev/ttyS2", O_RDWR | O_NOCTTY | O_NDELAY); `/dev/ttyS2` is linked to UART6. In the fex file, I have configured it like so: [uart_para6] uart_used = 1 uart_port = 6 uart_type = 2 uart_tx = port:PI12<3><default><default><default> uart_rx = port:PI13<3><default><defau…

Hi, I just got a NanoPi Neo Air, and I've tried both legacy jessie and ubuntu, as well as the nightly build, and with all three I have been unable to find the onboard wifi. When I run iwconfig, there is no sign of a wifi module; when I try nmtui there is nothing there to activate. lsmod shows the following: Module Size Used by evdev 9979 1 sun8i_codec_analog 13766 0 snd_soc_core 115473 1 sun8i_codec_analog snd_pcm_dmaengine 4221 1 snd_soc_core snd_pcm 70145 2 snd_pcm_dmaengine,snd_soc_core sun8i_ths 3134 0 gpio_keys 8517 0 uio_pdrv_genirq …

Hi, I've tested Armbian this week-end to replace my Cubian distro, and I failed to get the sound out of my speaker. I went back to Cubian X as sound works with stock image. Anyone could help me with it please ?

Hi, Does anyone has image for Orange Pi Zero 2+ H3 Ubuntu Dekstop Kernel > 4.x? Thanks.

Hi Martin and others I started a new Thread because have problems using some third party interfaces with OrangePI running Armbian. Well.. In my project I need to communicate with 5 sensors which have UART output so I decided to buy a circuit (uart2spi) which work well if connected to Arduino. The Circuit description is available here: http://www.rowlandtechnology.com/projects/2015/09/25/spi-to-4-x-uart-bridge-multiuart-project/ First step: This is how I have connected the circuit to GPIO bus on my OrangePi pc.. The circuit has (from left to right) +3.3V pin, MISO, MOSI, SCK (clock), CS and GND.. I have connected…

I've got a Cubieboard2 with a serial interface hardwired to PI10 and PI11 (uart5). The default Cubieboard2 DT overlay connects uart5 to PH6 and PH7, so I made a new dts, called "sun7i-a20-uart5b" with the pins like I need them: /dts-v1/; /plugin/; / { compatible = "allwinner,sun7i-a20"; fragment@0 { target-path = "/aliases"; __overlay__ { serial5 = "/soc@01c00000/serial@01c29400"; }; }; fragment@1 { target = <&pio>; __overlay__ { uart5_pins_a_2: uart5@1 { …

Greetings all. I've bought an Orange Pi PC recently, along with this screen, and I wanted to make the touch screen work on it. I have tried following this tutorial and this one, but so far I was only able to get the screen working. Currently installed image is: Armbian_5.35_Orangepipc_Debian_jessie_default_3.4.113. When I run `evtest` the only devices detected are `vmouse`, `sunxi-gpiokey` and `sunxi-ths`. I tried installing a GUI with xorg, lightdm and xfce. To show the GUI on the display I am using the following command: FRAMEBUFFER=/dev/fb8 startx But touch still isn't working. This is the output of armb…

I am trying to set up a video loop that runs continuous on boot up

TRYING TO CLONE EMMC FROM ONE NEO CORE INTO ANOTHER. I found this link below : https://github.com/zador-blood-stained/fel-mass-storage I still don't know if it works since i had to enter FEL MODE which i could not. maybe i am trying in a wrong way. SO how could i get a clone EMMC of nanopi neo core (taking into consideration it might not have FEL mode)? but if it does then how to enter this mode? and how to run this clone on another nanopi neo core?

Hello everyone, I've got an orange pi pite 2, I install in my sd card armbian, it start but when I login and create a new account and reboot, I see termianl and not the desktop of armbian, If i reboot it ask me again to login, but I can'f see the terminal.... PLEASE HELP....... THANKS

Edit: --------------------------------------------------------------- OrangePi PC+ ARMBIAN Buster and Focal v20.05.x Problem: I can't get UBoot to rotate the screen. Solution: I still don't know. --------------------------------------------------------------- Hi. I am using a Tablet Display with a controller (link) as a monitor, the case is that the controller is vertical (1536x2048) and I want to use the monitor in landscape mode (more normal). The ARMbian system of my OrangePi PC + single terminal without desktop starts rotated (vertical). Once started from the command line I can write: echo 3 | sudo tee /sys/class/graphics/fbcon/rotate_all …

Can someone please add support for the onboard microphone to armbian for the Lite2?! It is missing in armbian-config, there is no h6-analog-codec.dtbo in /boot/dtb/allwinner/overlay The microphone is wired up the same way as on the other h6 boards. Thank you very much!

Hi there! I've recently configured the ov5640 camera overlay and was able to capture videos either with mjpg-streamer of ffmpeg. Now on 6.1.34 both causes now a kernel oops. From the stack trace it looks like it happens inside v4l2 "media_pad_remote_pad_first" Unable to handle kernel NULL pointer dereference at virtual address 00000030 ... ... PC is at media_pad_remote_pad_first+0xa/0x58 I don't think v4l2 is the root cause because this may mean it fails alle the time which is unlikely. Looks like a null ptr gets passed in into media_pad_remote_pad_first ffmpeg used like this, but other parameters all resulting in the kernel oop…

I want to have a second NIC. I have a Cubietruck running. I am using Igor PeÄovnik's Cubietruck_Debian_4.0_wheezy_4.1.2 image. How do I get a USB network adapter to work. I have a USB 10/100 NIC plugged in and it does not appear as recognized ( no link lights). Thanks

Armbian_5.14_Orangepipc_Debian_jessie_3.4.112_desktop after upgrade sys not restart automatically

Hi, I'm using the orange pi plus 2e with armbian server installed on eMMC via the built-in script,as the title says i want ways to reduce boot times. I only need ethernet and usb since i will be using it as a "virtualhere" server. Thanks, linux super noob. regards.

Hello, I changed my memory card from a 8GB one to a 16GB one and I moved everything with Win32DiskImager, by reading the old one and writing to the second one. Can I expand my filesystem like on the first boot? Im running Jessie on a Orange Pi Zero. Thank you.

Hello, I am using Orange Pi PC Plus with Armbian Nightly. Since upgrade to kernel 4.11.0 audio stopped working, on kernel 4.10.11 everything was alright. When I am trying to open alsamixer i get error cannot open mixer: No such file or directory Can I fix it somehow? Can I still get last image with 4.10.11? Unfortunately it's not available at download page (too late).

This is on a fresh build of Armbian from source. I'm not seeing the camera appearing in /dev/video0, as you would expect. I've tried the solution that @sri suggested on this thread https://forum.armbian.com/index.php?/topic/3225-nanopi-neo-air-cam500b-issue/ but the device is still not visible. Here is the contents of my /etc/modules file #w1-sunxi #w1-gpio #w1-therm sunxi-cir hci_uart rfcomm hidp dhd g_serial ov5640 vfe_v4l2 And here is the output from dmesg [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux ve…

Anyone done kivy pip on Zero? Have problem with pip install kivy. Stuck on : /usr/bin/ld: cannot find -lGL collect2: error: ld returned 1 exit status

Checking in... NanoPi-NEO v.1.31 with the OLED hat... need to be a bit specific as there are multiple HW revs of the NEO - v1.2 and later moved from LDO to a DC/DC regulator, so info from 1.0/1.1 might not be accurate these days - still sorting out the regulator in use, as there are a couple of options with Allwinner H3 there. I think it's the SY8113B, but hard to tell... Testing with Armbian 5.61 vs. FriendlyArm's 4.14.52 build for their OLED hat (I'd source a direct link, but they have two source - baidu and google drive) -- The friendlyarm image is pretty good with temps on the 4.14.52 kernel, typically around 31-33c idle, and I've not seen temp…

Seems like it won't boot and stucks at: INFO: PMIC: DRAM voltage: 1.50V INFO: Continiously reboot. Can't understand why. Any advice?

board: http://nanopi.io/nanopi-neo-core.html image: Armbian Bionic mainline based kernel 4.19.38 from https://www.armbian.com/nanopi-neo/ There are two SPI separated buses with separated pins on NanoPi Core: SPI0 and SPI1 /boot/armbianEnv.txt: ... overlay-prefix=sun8i-h3 overlays=analog-codec i2c0 spi-spidev uart1 usbhost3 param_spidev_spi_bus=0 ... /dev/spidev0.0 presents How to activate a SPI1?

HI, I have OrangePiPc and need to activate 3 uart (TX-RX) pins as system serial ports (/dev/ttyAMA0, /dev/ttyAMA1, /dev/ttyAMA2) how do it?

Hi, After upgrading linux-image-current-sunxi64 package from 21.08.1 to 22.02.1, bringing kernel version 5.15.25, the CPU temperature raised abnormaly on my olimex teres board. Temperature is above 60°C at startup, whithout any activity or load average. The issue persists with latest 5.16.16 kernel from linux-image-edge-sunxi64 package. I noticed temp at startup around 30°C with 5.4.88-sunxi64 kernel, 40°C with 5.10.60-sunxi64 kernel and above 60°C with 5.15+ kernels. Does anyone have cpu temp issue with 5.15+ kernels ?

For a long time, for more than three years, I did not use my BananapiPro board. And recently I decided to launch it again.I downloaded new Armbian image distribution. But the system when loading gives out an error. After the initialization of the devices, a message appears: Device 0: unknown device ethernet@1c50000 Waiting for PHY auto negotiation to complete......... done Speed: 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.2.200 (5ms) *** Warning: no boot file name: using 'COA802c8.img' Using ethernet@1c50000 device TFTP from server 192.168.2.1; our IP address is 192.169.2.200 Filename 'COA802C8.img'. Load address: 0x42000000 Loading: T T T …

Hi, I use an OrangePi Zero as a race timer for a car. It is powered from the car. So when the car starts the OrangePi gets power and boots and when the car is turned off the OrangePi loses power and "turns off". This isn't ideal but I don't have a lot of options. I feel like this is a fairly common use case for electronics in cars especially ones like race timers etc. Unless I have a battery as well. I was wondering what are the best things to do to protect against the sudden power loss so that I don't corrupt anything? Is it possible to make parts of the file system read only maybe? All I do with the OrangePi is run a C++ application, it use…

Hi All, after next collapse of our network I used the hammer to destroy the R1. This board is really shit and I will never ever continue with any kind of experiments with it. The reason is probably BCM chip. But I am not sure. Everything works well on the table, you can stress it as much you want , everything works well. But when you use it for real traffic, the board starts to collapse, unexpected restarts etc. I followed all recommendations of you, but without success. The question is ... Which board for router I have to use? Any ideas welcome. Petr P.S. If somebody wants R1 for home router/NAS (for home is ok), I have two available, the third ended …

Hello, what is the difference between /sys/devices/platform/sunxi-i2c.0/i2c-0/0-0034/temp1_input this return 37800 and /sys/devices/platform/a20-tp-hwmon/temp1_input this return 46500 what value is correct? there are writing http://bananapi.com/index.php/forum/beginners/141-how-to-read-cpu-temperature You can find the CPU temperature data at "/sys/devices/platform/sunxi-i2c.0/i2c-0/0-0034/temp1_input" but bash.bashrc.custum use value from /sys/devices/platform/a20-tp-hwmon/temp1_input thanks hw: Banana Pi BPi-M1+

Hello, I have just bought a bananaPro. I would like to learn a little by installing armbian and enabling the video acceleration. Currently, I have no LCD display, so I would start to install Debian Wheezy or Debian Jessie (legacy) so that to be able to log in through ssh. Nevertheless, on the download page for bananaPro it is said that "Mali drivers fails to compile". Is this driver mandatory for video acceleration to work ? I figured out it was rather related to cedarX. Then, which armbian image is best suited ? Thanks in advance for some piece of advice. Best regards deb2016

Good evening. I am preparing an Orange PI Plus 2 in order to be the first computer for my 8 years old son. The idea is that he could learn Scratch by watching some video tutorials in YouTube The problem is that actually, if you pause a video, and the you want for it to restart, only video does it. Sound doesn't starts again.It remains muted. Then, if you click to watch another video, sound come back. But you loose it again if this second video is also paused. It's a bit annoying. Do you have the same issue ? Best regard. Maesstrissimo.

Hi! My Banana pi Pro with Armbian v5.20 does not boot since i issued a 'init 1' command. While booting, it show only that; Starting kernel ... Uncompressing Linux... done, booting the kernel. How to activate the boot debug mode. I tried many keyboard keys without success. Thank you!

It was set to mount cifs in fstab, but seem not automatically mount. Since this is not supported?

I'm trying the new version of armbian for orange pi plus 2 . Is there some news to create an access point ? I saw there are some files and other files not Does someone could link to me some tutorial for the access point? I have several usb dongle wifi and wifi on chip After a lot of web sites I visited I'm not able to create an access point thanks

Hello, I just bought an OPi-Zero and loaded Ubuntu image with legacy kernel(tried the debian one too).Wifi is failing to load for some reason.I checked various posts in armbian forum and checked that xradio_wlan driver is loaded twice,as suggested. kernel module dhd is blacklisted as well. This is the dmesg output, Spoiler [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.4.113-sun8i (root@devel) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.4) ) #10 SMP PREEMPT Thu Feb 23 19:55:00 CET 2017 [ 0.000000] CPU: A…

Hi everybody, I have an OPZ board (256 mb). I couldn't manage to start work wifi in automatic mode. I tried manual configuration then tried nmtui in both cases wifi starts only after Ethernet plug was connected. OS: ARMBIAN 5.25 stable Debian GNU/Linux 8 (jessie) 3.4.113-sun8i How can I solve this problem? Thanks!

[EDIT: The solution to this was realizing I'd been handed Banana Pi's (which have no WiFi), not Banana Pro's (which do have WiFi). I wasted a few days on this.] Hey guys, I'm sure you're sick of hearing this, but I have no WiFi with latest Banana Pi Pro image. No errors in dmesg, lsmod shows "brcmfmac" is present, but no device in iwconfig.

Hello! I asked this question here: https://github.com/zador-blood-stained/fel-mass-storage/issues/1, but I decided to ask again. Is there a way to boot the current mainline u-boot via FEL? Is it easy to support this issue? I would be happy to receive any help. Thanks, Aleksandr

Hi, can anybody please help me with device tree overlays to enable serial uarts? Maybe I'm missing a step or I'm doing it wrong? UART3 and UART4 are not working on Cubieboard2 and Cubietruck running the latest mainline armbian image. I've added the dto by following command: echo overlays=uart3 uart4 >> /boot/armbianEnv.txt dmesg shows they are enabled: root@cubieboard2:~# dmesg | grep tty [ 0.000000] Kernel command line: root=UUID=871ffecf-ac1f-4168-bca0-f4ba6a2d8f33 rootwait rootfstype=ext4 console=tty1 console=ttyS0,115200 hdmi.audio=EDID:0 disp.screen0_output_mode=1920x1080p60 panic=10 consoleblank=0 loglevel=1 ub…

Today I was going through my cupboard and did find a original pcDuino (v1) with A10-CPU and 1GB of Ram. In my mind I got the pcDuino v2 download-page of armbian. As JohnGo did wrote May 2016 on this page is a picture of the pcDuino v1: So I checked the specifications v1 <--> v2 and found ony that v2 has only a WiFi-Board soldered where on the v1 is a additionally USB-Port. Also the v1 is missing the Arduino-Headers, but has some other pin-rows for GPIO and so on. CPU (single-Core 1Ghz) and Ram (whopping 1GB for 2012) is the same I wrote the pcDuino v2 Image to a uSD and booted it without problems. (and changed /etc/upd…

Hi folks, I'am setting up an Orange Pi Zero with Armbian_5.38_Orangepizero_Debian_stretch_next_4.14.14.img. After "sudo apt-get install dnsmasq" the system responds: Err:1 http://httpredir.debian.org/debian stretch/main armhf dnsmasq-base armhf 2.76-5+deb9u1 Could not resolve 'httpredir.debian.org' Ign:2 http://httpredir.debian.org/debian stretch/main armhf dnsmasq all 2.76-5+deb9u1 Err:1 http://security.debian.org stretch/updates/main armhf dnsmasq-base armhf 2.76-5+deb9u1 Could not resolve 'httpredir.debian.org' Err:2 http://security.debian.org stretch/updates/main armhf dnsmasq all 2.76-5+deb9u1 Could not resolve 'httpredir.debian.org'…

I bought a Cubieboard AIO A20 Einstein and wanted to install Armbian. Is there an image I can use to get access to this board? I tried a few images following the install with sd card with no success. I have gone back and forth burning images, reformatting the drive, test and trying again. I'm a newbie but I have completed several installs on other machines just not one like this. I'm outside my comfort zone but keep on trying. I can install to msata and boot from that and there are boot settings in the Cubie desktop. Knowing what image to use (if any for Cubieboard AIO A20 Einstein) moving forward would be helpful. Any other tips, suggestions, how to's, and successes wou…

Hi, I recently reinstalled an orange pi 2+ with Armbian Stretch mainline kernel 4: root@ted1090-7:~# uname -a Linux ted1090-7 4.14.18-sunxi #24 SMP Fri Feb 9 16:24:32 CET 2018 armv7l GNU/Linux I also installed it on EMMC (this way, with this u-boot-sunxi-with-spl.bin). Now this orange pi crashes every couple of days (sometimes with a couple of hours). This orange pi use to run with Armbian legacy 3.x kernel on EMMC without any issue: pi@ted1090-6 ~ $ uname -a Linux ted1090-6 3.4.113-sun8i #18 SMP PREEMPT Wed Jan 24 22:10:49 CET 2018 armv7l GNU/Linux Exactly the same applications are installed (dump1090 and dump1090-tools). T…

I have an Orange Pi One Plus with the H6 chip in it and I'm quite happy with how well it's supported by Armbian. I haven't really had any problems with it. I do have one question, though. I'm using armbianmonitor to "-m" monitor the machine and I notice that the temps are always pretty hot. Even at idle (480MHz) it still shows 72C. That seems higher than I would have expected. Is this normal, expected behavior? I understand that the SoC thermal monitoring code in the kernel is pretty new and therefore might not be perfect, yet. So, I thought I'd ask. Because it may just be my board that's off. Does anyone know if this is normal? Info: …

Hi all, Orange Pi One Armbian_20.02.0-rc1_Orangepione_bionic_current_5.4.14 Enable w1-gpio /boot/ambianEnv.txt: overlays=w1-gpio param_w1_pin=PD14 param_w1_pin_int_pullup=1 dmesg | grep -E 'w1|wire' [ 5.271798] Driver for 1-wire Dallas network protocol. [ 5.304021] gpio-110 (onewire@0): enforced open drain please flag it properly in DT/ACPI DSDT/board file What and where else needs to be done?

Hi I would like to know whether I can use orange pi lite 2 image on orange pi one plus. I tried it but eth0 is not visible. Is there a way to tweak it? The reason is I want to create an image with various packages installed. So that i do not need to maintain 2 sd images since both are H6. Tq

Hi Armbians I am running mulitiple TOR network relays on Cubietruck boards (Cubieboard 3) in different Datacenters with synchronous 100 MBit/s internet connection each board (by ethernet plug) for 1- 1,5 years now. At the beginning each board could handle 25 MBit/s incomming and outgoing traffic the same time easy and 24/7. The boards are running the latest Armbian build with kernel headers installed and full firmware package. But now, as you can see here, my Cubietrucks are getting slower after time, with the network traffic they can handle via eth0: https://metrics.torproject.org/rs.html#details/EC9C4CDB403204731122C9D3FA44DFAE6…

I compiled Armbian-unofficial_23.11.0-trunk_Olinux-som-a13_jammy_current_6.1.63_minimal.img Burn it to sd card, and tried to run it on my old Allwinner A13 laptop, and is got this Error message: U-Boot 2023.10-armbian (Oct 14 2023 - 01:13:59 +0000) Allwinner Technology CPU: Allwinner A13 (SUN5I) Model: Olimex A13-Olinuxino DRAM: 512 MiB Core: 59 devices, 21 uclasses, devicetree: separate WDT: Not starting watchdog@1c20c90 MMC: mmc@1c0f000: 0 Loading Environment from FAT... MMC: no card present ** Bad device specification mmc 0 ** Setting up a 1024x768 vga console (overscan 0x0) In: serial,usbkbd Out: serial,vidconsole Err: …

Can anyone help to provide guides since it is disable by default? Thanks in advance.

Hello world !, I am running bananapi and cubietruck boards on Ubuntu Thrusty and legacy kernel 3.4.109. I am using these board for remote servers but before critical upgrades like upgrade of kernel which can cause unusable system I need powerdown these boards and do backup of entire sdcards. But commands "poweroff" or "init 0" with battery connected everytime causes reboot on both of them while without battery connected these command shutdown boards properly. Any ideas ?

Hi. Any idea about including snappy ubuntu core in the build process?

OPI pc frequently hangs when transferring from or to file from any usb hdd. OPI PC freezes and never become operative till power shut and boot. kindly post any remedy. rizwan

Hi, I'm watching a problem during boot of my A20-OLinuXino-MICRO-4GB, running 4.6.3-sunxi #7 SMP Tue Jul 5 16:23:41 CEST 2016 armv7l GNU/Linux It seems to hang an multiple points and needs 417 seconds at all. It looks like a problem with initializing /dev/random and network configuration Here the entire log: Aug 30 00:23:49 autokino kernel: [ 7.624658] rt2800usb 1-1:1.0 wlan0: renamed from rename4 Aug 30 00:23:49 autokino kernel: [ 8.917512] random: mktemp urandom read with 96 bits of entropy available Aug 30 00:23:49 autokino kernel: [ 9.142494] EXT4-fs (mmcblk0p1): re-mounted. Opts: data=writeback,commit=600,errors=remount-ro Aug 30 00:23:49 autokino ker…

I got 2 x Orange PI pc+ running Armbian (install by same SD card on eMMC). My two orange pi pc+ got same wlan0 mac address. I did research on forum and saw some suggestion about bug of Network-Manager. I try remove (purge) Network-Manager but see no difference. I also try look in u-boot but don't know how to set mac address on the u-boot part. How should I make my 2 pc+ board have difference mac address? want to run these two board under the same wifi network. Please suggest. Thank you very much in advance.

I try to make LIRC work on NanoPi Neo Air ! A very nice board For the moment I get nothing when I run : mode2 -d /dev/lirc0 It should return pulse and space when I trigger 5V/GND on pin6 : (ref http://nanopi.io/nanopi-neo.html) cat /sys/kernel/debug/gpio GPIOs 0-383, platform/sunxi-pinctrl, sunxi-pinctrl: gpio-10 (blue_led ) out lo gpio-354 (? ) out hi gpio-362 (green_led ) out hi Does lirc pin is accessible on connector ? I guess I can check on which Gpio is it connected, but where....

I use Mainline 4.9.7 Ubuntu Xenial and wan`t to disable wlan and bluetooth, cause i don`t need. Where can i do this?

I am trying to use gpio without C or Python library, I follow pinout in the wiki : http://wiki.friendlyarm.com/wiki/index.php/NanoPi_NEO_Air 7 GPIOG11 203 modprobe gpio-sunxi echo 203 > /sys/class/gpio/export echo out > /sys/class/gpio/gpio203/direction echo 1 > /sys/class/gpio/gpio203/value LED I connected to Gpio don't light for the moment, I have missed something ? What Linux Gpio may I use ?

Hi, After running the default image with legacy kernel for a few weeks, I am now trying the run a fresh SD card with the latest build of the mainline image. However, the MAC address of my device appears to be changing after each reboot - and I am running about of ideas to fix this issue. What I've tried so far: - Edit script.bin & add MAC address in the [dynamic] section - Edit armbianEnv.txt - Define an address in /etc/network/interfaces So far, I have not been able to solve the problem. Your help is much appreciated. Any suggestions on possible fixes for the issue?

I find orangepipc packages in http://apt.armbian.com/dists/stretch/main/binary-armhf/Packages they are: linux-stretch-root-dev-orangepipc v5.37 linux-stretch-root-next-orangepipc v5.37 linux-headers-sun8i for kernel-3.4.113 v5.35 linux-image-sun8i for kernel-3.4.113 v5.35 linux-u-boot-orangepipc-default v5.35 same as they in Jessie.. what's the status about debian stretch on orangepipc? gfx, network, video?

Hello, i have a old Banana Pi M2 with the current Armbian in use. I use the green LED with Heartbeat Signal. Today i try to connect with putty but after Username and PW nothing happen. Samba Service work normal. Then i have look at the Banana and the green LED was lightning constant and no heartbeat blinking. Maybe the trouble was because in a few meters distance sawed with a circular saw. Has perhaps caused interference or power fluctuations. No idea and maybe just coincidence. I have been using Armbian for only two days. Previously, the manufacturers ran Distribution for two years. I have Google and found out t…

I just received 3 of the Zero Plus boards and am trying to verify they at least basically work. I'm new to Armbian & Orange Pi but have been using Raspbian & Raspberry Pi's for years. I've downloaded Armbian for the OP Zero (Armbian_5.38_Orangepizero_Debian_stretch_next_4.14.14.img), verified the gpg signature and the sha256 checksum and used Etcher v. 1.4.4 on a 2017 iMac, macOS Sierra, to burn SD cards. After burning, macOS claims "The disk you inserted was not readable by this computer." Maybe that's normal for Armbian? diskutil list shows: /dev/disk8 (external, physical): #: TYPE NAME SIZE …

Hi, is WoL supported on orange pi? I have orange pi pc+ and ethtool shows letter d next to Supports Wake-on , cant turn it on. Maybe I need to compile module with support?

Hi. I am having this issue with Orange PI PC. If it boots up when the TV it connects to over HDMI is off, I am getting blank pink screen. I guess it is because it chooses different video output when TV isn't detected. Raspbian forums suggest disabling "HDMI hotplug" by editing /boot/config.txt , but Armbian hasn't got this file. Please share your suggestions as this TV is on the wall in my kid's school at 2m height - and if it reboots due to short power failure, it needs a ladder to get fixed. Please help me before school year starts

Good morning all. I was trying to power up my nanopi M1 through the VDD_5V and GND pins shown in GPIO.jpg image and/or the power pins on the debug GPIO pins, the schematics of the board power electronics are attached too on page 7 and 8, may by I'm wrong but what I see on those schematics is that all the power switchs and DC/DC converters can be powered through those pins but when I do that using a USB cable cutted on the micro USB side and prepared with the right terminals to fit the pins -with a 5V USB charger- then the tension drops aproximatelly to 4.60-4.67 DCV, the board starts by lighting dimly the power LED (as normally) but when the power LED lights strongly also…

over year end I tried to re-set up my 2 cubietrucks , one as a a: music machine b) server. a) Pity is, Volumio is no longer available for Cubietruck - anyone has a later image than 2.118? Any other proposal? b) When trying to find a workable image for Igors selection, I figured that I run into issues with all of them. Test 1 Armbian_5.69_Cubietruck_Ubuntu_bionic_next_4.19.13.img boots initial input on hdmi,then neither on hdmi nor on VGA ???? ssh works, login as root works sudo armbian-config Boot from SD - system on hdd - works sudo apt-get update sudo apt-get upgrade boot from SD - works, but still 'headless', no …

Hi All. May be I miss something but I do some searching and still can't understand. Problem configuration: Orange Pi PC v 1.2 (try 3 different) fresh loaded Armbian_5.90_Orangepipc_Ubuntu_xenial_default_3.4.113_desktop.img (try different SD cards) any (try 3 different HP 2824, Zyxel Kinect, Cisco SRW2016) If I plug my Orange Pi PC with this image to 1Gb port I'v got blinking of lights and dmesg: [ 818.090335] PHY: gmac0-0:00 - Link is Down [ 819.090497] PHY: gmac0-0:00 - Link is Up - 100/Full [ 821.090494] PHY: gmac0-0:00 - Link is Down [ 822.090314] PHY: gmac0-0:00 - Link is Up - 100/Full [ 824.090335] P…

I apologize for asking such a basic question. I have recompiled the wifi module on an Orange Pi PC+ to operate in concurrent mode so it can act in both station and AP mode at the same time, allowing it to be a wifi repeater. The problem is, this feature is lost on every kernel upgrade, requiring me to recompile the module each time I upgrade the kernel. The kernel module driver often changes slightly between kernel versions, and I have to track down and fix new bugs in the source code that prevent it from compiling when concurrent mode is enabled. I'm happy with how the wifi module performs now, but don't want to lose the ability to get needed kernel updat…

i have a project and i need to activate the vga output on my banapi m1. I searched the forum and found this link https://forum.armbian.com/topic/6292-banana-pi-enable-tv-outrca/ but I think it only applies to old kernel versions. The only reference I entered for these more recent versions was this https://docs.armbian.com/Hardware_Allwinner/#how-to-reconfigure-video-output but I don't know how to activate the video output Can someone help me? thank you

Hi, we are trying to make our Orange PI zero with custom shield working with an MCP2518FD on board with SN65HVD23 tranceiver. We started from the normal kernel already built, but according to this thread we found that it must be activated at compile time. So we downloaded the repo and built the Armbian image with this CAN configuration: CONFIG_CAN=y CONFIG_CAN_RAW=y CONFIG_CAN_BCM=y CONFIG_CAN_GW=y CONFIG_CAN_J1939=y # # CAN Device Drivers # CONFIG_CAN_VCAN=y CONFIG_CAN_VXCAN=y CONFIG_CAN_SLCAN=y CONFIG_CAN_DEV=y CONFIG_CAN_CALC_BITTIMING=y CONFIG_CAN_FLEXCAN=y CONFIG_CAN_GRCAN=y CONFIG_CAN_SUN4I=y CONFIG_CAN_TI_HECC=y CONFIG_CAN_C_CAN=y CO…

Hi Everyone, Is there anything additional required to enable better performance improvements (kernel patch for TXTS and RXTS are set to 3 each see below link) on a Banana PI running Armbian V21 / V22 ? I have updated the bootloader, and OS, and the performance is still abysmally poor. Mechanical or SSD drive connected to on board SATA yields a whopping 2.7-10 MB/sec write speed using dd with a large block size, or with the iozone tool ~5 upto ~45 for larger block sizes. Still a very far cry from the ~120 after the kernel patch applied in ~2019 => https://forum.armbian.com/topic/10352-a20-sata-write-speed-improvement/ …

I have an H618 Android TV Box with 8GB of RAM and 256GB of storage. Any build option results in an error. I would be immensely grateful for any help. Thank you. armbianarm_errors.txt

Hi to All! Currently i am using 3.4.107-cubietruck #14 SMP PREEMPT Wed Apr 29 11:57:42 CEST 2015 armv7l GNU/Linux including a WLAN USB Adapter AWUS036AC from ALFA. First question: Does anybody got this adapter to work with a cubietruck as a WLAN-AP? Second question: If yes, what driver did you use for the successful implementation? Third: How to disable the onboard WLAN? I want to use it as a 5GHZ (AC-standard) WLAN-AP! Many thanks in advance. Regards, Ireng

Hello, I'm running armbian on the cubieboard 2 and have noticed something that might be an unexpected behavior: when running on NAND, the nand2 partition is mounted with ordered data mode (despite the fstab configuration)! It looks like the system tries to remount the partition in writeback data mode, but it is not allowed to, according to the following messages: root@siamserver:~# dmesg | grep EXT4 [ 12.504386] EXT4-fs (nand2): mounted filesystem with ordered data mode. Opts: (null) [ 17.557900] EXT4-fs (nand2): Cannot change data mode on remount [ 17.604119] EXT4-fs (nand2): Cannot change data mode on remount As the official cubieboard 2 download page st…

Hi all. Strange thing happens. I've tried to run a fresh installation of the 4.4.3 kernel version of armbian 5.04. The first boot takes forever (I gave up after 2 hours; a few times). It started and hung up at updating packages. Every try; tried about 10 times. If I switched to 5.04 with kernel 3.4.110 - the first boot takes about 1minute and cubietruck rebooted once, so everything worked perfectly. Any idea what could happened? Some extra info: If I logged in during this "updating packages" period, the normal process of creating a new user worked as normal. After that I could restart the cubietruck normally. So my question: Do I get some problems if I …

I use your toolchain to build a Armbian_5.11_Orangepih3_Ubuntu_xenial_4.6.0.raw image, and then dd to SD card. Both OPi One and OPi PC can't boot it correctly. In the 1st time booting, the LED flashed for a while, and then re-boot automaticlly, and then in the 2nd boot and then, the serial port console only see this: U-Boot SPL 2016.05-rc1-armbian (May 09 2016 - 21:49:38) DRAM: 512 MiB Failed to set core voltage! Can't set CPU frequency Trying to boot from MMC1 U-Boot 2016.05-rc1-armbian (May 09 2016 - 21:49:38 +0800) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi PC I2C: ready DRAM: 512 MiB MMC: SUNXI SD/MMC: 0 *** Warni…

Hi everyone, I'm trying to connect Tiny LCD to OrangePiOne. I bought this cheap LCD display with touch panel. http://www.aliexpress.com/snapshot/7757492669.html?orderId=75894630877559 --My environment-------------------------------------------------------------------------------------------------- Orange Pi One Armbian Jessie Desktop with legacy kernel DS1302 RTC module(work with WiringOP) 720p DVI Display 2.8" SPI Serial Port 240x320 ILI9341 TFT LCD Display Screen Touch Panel Backlight Module ------------------------------------------------------------------------------------------------------------------------ I connected and tried to configure the L…

Hi, since I do have 2 hdd connected to my cubietruck, i would like to customize 30-sysinfo in such a way, that it shows the disk usage of both hdd (dev/sda1 & /dev(sdb1) at login! Any suggestions on how to achieve that?? best reagrds, in advance for your help and support regards, Ireng

Hi everybody I'm using Orange PI One with OS Armbian Debian GNU/Linux 8 (jessie) 3.4.112-sun8i (Server) I need to convert some videos for make video stream(H264) but it works so slowy(3~10 fps) when I use ffmpeg. I think ffmpeg works slowly because it doesn't use HW Codec so how can I enable it in H3 CPU and use it in ffmpeg?

I don't know if this is something I have broken or not, but I have a \var\log and a \var\log.hdd both identical and both being updated. Where should I be looking to rectify this duplication? ARMBIAN 5.25 stable Debian GNU/Linux 8 (jessie) 3.4.113-sun8i OrangePiZero

Hi how i can enable usb driver modem 3G/4G model: Huawei E3272? Board type: Cubieboard 1 OS: armbian ubuntu xenial Legacy 3.4.113/ Mainline 4.9.7 Module huawei_cdc_ncm.ko driver is missing in kernel. How can I compile it in addition? I do not understand the kernel assembly? I use wvdial and sakis3g! Best regard Jaskies.

Hi! Thanks for your amazing work, i'd like to have knowledge to give a hand After a few problems I've been able to boot my new Orange Pi Prime, but no keyboard is working on it. I've tried with an USB keyboard and a bluetooh one, but there is no way to make them work. No clues on dmesg, lsusn looks fine... Any idea about hoe to debug it?

good night, is ethernet and usb a shared hub on Orange Pi Plus 2E and H3 SOC? i get max dl\up speeds on speeds tests and good write and read speeds but when i dl something it max at half my Internet speed thanks

Hi all, I'm trying to access the GPIO from python context and I absolutely need to do it in a rootless way. (WSGI apache module) I'm a newbie and noticed that this is the library command causing the error inside the python library: Code: Select all fd = open("/dev/mem", O_RDWR); I do have /dev/mem on my armbian distro and clearly the access to /dev/mem is root limited, what's worst I don't have /dev/gpiomem Is there a way to create /dev/gpiomem so I can add the apache user to gpio group and solve this? Do I need to configure and compile a kernel by myself? please help me, thank you

Hi, how are you? I'm trying configurate my OPI zero to manage users of my network using Dalo Radius (Tutorial of this forum), but I need configurate to work with ETH1 (a Gigabit USB adapter) and no have find the configuration for change this... And if I connect the adapter, I'm loss the connection with OPI... I'm using a TP-Link Archer C60 to distribute my network via Wi-Fi, but using a PSK. I want to remove the password and use via radius to add and remove users of my network, with the vantage of captive portal. Via ETH1 I don't have any idea to where start, via Wi-Fi of Orange PI I'm no try because is not usual for me... *Sorry for my bad english..…

I have a NanoPi Neo Air (Allwinner H3 SoC) with onboard wifi and a serial interface. Unfortunately during some late hour hacking I managed to accidentally connect 5V onto its TX pin, I think effectively screwing up its UART0. I can no longer connect to it via a USB to TTL Serial cable. Looking at the NeoPi Nano Air's pinout diagram, it seems to have more UART devices (UART1 and UART2 even) so I wonder whether there's a way to set up armbian to communicate via these during boot? Another idea I had was to try to bypass the UART completely and to hook up the board via the wifi. Now, without having any access to a serial console, I need to …

Hi, I was wondering if anyone was having issues with the ethernet port using the legacy kernel ? It does seem to kind of work ... it will get DHCP from the router and configure the routing tables etc but after that it goes wonky. When I do a ping test from the router I get "50/50 transmitted, 15/50 received, 70% loss". A ping test from the opi-win to the router gets a similar result. If I try a ping/ssh from a PC connected to the router I get a 95% packet loss Everything else seems to work fine ... HDMI, USB, WiFi (AP/STA modes) which is really, really nice. Thanks TB

Hello there, I was looking at the gc2035 camera sensor for the orange pi device. I want the camera module to load as fast as possible and take pictures as fast as possible. When I use a USB camera, it takes 2-3 seconds to load the module and activate the camera, and the camera takes 2 seconds. I'm thinking of compiling the GC2035 camera statically to the linux kernel. But I'm not sure how much time decrease. What I would like to know is, how fast is the camera taking pictures and how long is the loading time of the camera modules? Can I take pictures under 200 ms with the camera triggered? The Raspifastcamd module allows …

Hello, on older Orange Pi zero I used nmcli for creating access point or connecting as a client to wifi. Now I am running Linux orangepizeroplus2 3.4.113-sun8i #4 SMP PREEMPT Wed Nov 22 13:45:28 CET 2017 armv7l on Orange Pi Zero plus2 h3 but I am not able to create access point with this (it does not work as on older OpiZero, I am using the same commands): nmcli c add type wifi ifname wlan0 con-name connection-name autoconnect no ssid hotspotssid nmcli connection modify connection-name 802-11-wireless.mode ap 802-11-wireless.band bg ipv4.method shared nmcli connection modify connection-name wifi-sec.key-mgmt wpa-psk nmcli connection modify connection-name …

Greetings all. I am having no success getting access to gpio pins in NR using opi-gpio. I am trying to re-build a system that I messed up due to an update. The update broke access to the 1-wire host adapter I had running on I2C. I have searched and read a lot trying to find a solution but I am not making enough sense of the solutions I read to even know if they apply or if I am applying them correctly. Very frustrating because I had this working once but that was a number of versions ago for both armbian and NR. Also, the gpio pins were working even after the I2c update. In the process of 'fixing' that I started over with current armbian: mil…