Allwinner sunxi

http://paste.armbian.com/icedujiguw.yaml Hello everyone, trying to give new life to this old Orange Pi+ 2. Here is described what hapens when i try to boot up latest image. Can anyone help. Thanks in advance. Armbian 23.8 Bookworm Kernel 6.2.y, Size: 421Mb, Release date: Jun 3, 2023 SBC gets stuck after the request Sense .. and doesnt booy up, if i plug a device in usb ports, it bootloops .. see below using same sd-card and a diffrent image file works with no issues . hardware : grounded out pin 9 of the SD card slot (checked with multimeter and works) U-Boot SPL 2022.07-armbian (Jun 03 2023 - 19:37:25 +0…

First : i downloaded both Armbian versions for "Orange Pi+ 2" but reported link file names where different from those that actually download : a) link says https://dl.armbian.com/orangepiplus/Ubuntu_xenial_default_desktop.7z, but download file is Armbian_5.38_Orangepiplus_Ubuntu_xenial_default_3.4.113_desktop.7z b) 2nd link says https://dl.armbian.com/orangepiplus/Debian_stretch_next.7z, but download is Armbian_5.38_Orangepiplus_Debian_stretch_next_4.14.14.7z Second : after download i extracted both with : 7z e filename.7z then i run etcher 1.4.4 cli : ./etcher -d /dev/sdd filename.img -y , result sdcard writed, then i inser…

Hi, I have a question about distro upgrde. This is the information on welcome screen: Packages: Ubuntu stable (jammy), possible distro upgrade (noble) Support: DIY (community maintained) I checked the release info on https://www.armbian.com/orange-pi-plus-2e/ and the noble is available. I used sudo apt dist-upgrade and it found no upgrade. Is there any wrong with that? And how I can do the dist-upgrade except writing a new image?

After upgrade to latest kernel (4.19.38) my device only boots into maintenance mode. System is on emmc and no problems before. I started armbian-config and switched back to previous kernel, but it doesn't boot system. Even with all USB devices disconnected it didn't start (as i see there are some usb errors in log), file system seems to be clean, just didn't start system in normal mode.... Any advice? Thx Update: OK, solved, after installing latest updates within maintenance mode its ok again....

Hi. My platform is Orange Pi Plus. I connected SATA HDD and installed Armbian. Using nand-sata-install I created the following scenario: boot from SD, system on SATA. I also installed lighttpd. Several days everything works fine and than: ...file system on the root filesystem failed … rebooting automatically due to panic= boot argument... After that the PC just reboots constantly and I can do anything. The only solution I found is to repeat the process of boot SD creation. But after that I need to install everything again. All this I already did for several times... What maybe the reason of this error? Can I exclude the SD card and use eMMC instead? Is there anythi…

Please help me build driver for usb wifi adapter Tenda u12 (RTL8812AU chip). Board Orange Pi+2 (Armbian OS https://dl.armbian.com/orangepiplus/Ubuntu_xenial_default_desktop.7z) adapter driver link http://tendacn.com/en/download/detail-2863.html build log with error Spoiler root@orangepiplus:/home/alex/Desktop/RTL8812AU_linux_v5.1.5_19247.20160830# sudo sh ./install.sh ################################################## Realtek Wi-Fi driver Auto installation script Novembor, 21 2011 v1.1.0 ################################################## Decompress the driver source t…

Hello all, I cannot get stereo output from the headphone jack on this device. Until last august I had an image of debian jessie (kernel 3.x) and this was working fine (IIRC stereo was OK). I used mycroft AI to read the microphone and play sounds, also used MPD music server, blablabla etc a great configuration. Something happened during one upgrade operation and I lost my boot so I thought "why not take this opportunity to flash a new image". Mistake. BIG mistake. Now I cannot get any application to output stereo audio and also I cannot get any application to use the microphone. Can someone please help out at least gett…

Hi! Is the Orange Pi3 image suitable for the Orange Pi3 LTs? Or where to find it?

Short issue description: sometimes after pulling a USB device out it makes OPi3 USB host controller stuck. One or more USB ports are getting unresponsive (sometimes all four of them) and no messages in dmesg about connection/disconnection. No matter what device is used. This thing happens only on the first host controller, the second rear one is functioning and responsive. It happens more often if we push in and pull out four devices in a short period of time. Wherein /sys/kernel/debug/usb/devices is stuck too, we cannot read the info from it and all the utils (vi, cat, etc.) are getting the D state (uninterruptible sleep). "lsusb" is also not working, but can b…

Hello. I have a problem on my Orange PiPC+ board. After playing mp3 file, I hear some sound click. As I understand, snd driver goes to the power save mode. I tried to disable it. I set snd-soc-core.pmdown_time=-1 It did not work for me. How can I fix it? Additional information: clock@orangepipcplus:~$ uname -a Linux orangepipcplus 4.19.62-sunxi #5.92 SMP Wed Jul 31 22:07:23 CEST 2019 armv7l armv7l armv7l GNU/Linux clock@orangepipcplus:~$ sudo armbianmonitor -u System diagnosis information will now be uploaded to Please post the URL in the forum where you've been asked for. I don't see…

I found the way to install, keep updated and easily uninstall plexmediaserver without using armbian-config. here is the link https://forums.plex.tv/t/read-me-first-about-server-armhf-arm64-debian-ubuntu-raspberry-pi/226567. I used the version arm64 / ARMv8 and on OPzeroplus with H5 works very well. Spoiler arm64 / ARMv8 # become root sudo su # add my public key wget -O - https://dev2day.de/pms/dev2day-pms.gpg.key | apt-key add - # add my PMS repo echo "deb [arch=armhf] https://dev2day.de/pms/ stretch main" >> /etc/apt/sources.list.d/pms.list # activate https apt-get insta…

Getting FDT_NOT_FOUND(spi-add-cs1) and FDT_BADMAGIC(spi-dev-1) on uboot.

Hi Guys, Sorry if this question has been tabled before, but i couldn't see it amongst the H5 topics. I just bought two O-pi-zero+ and downloaded the two mainline releases from https://www.armbian.com/orange-pi-zero-plus: Armbian_5.38_Orangepizeroplus_Ubuntu_xenial_next_4.14.14.img and Armbian_5.38_Orangepizeroplus_Debian_stretch_next_4.14.14.img both seem to work just fine until i try to disable any of the CPUs, for example: "echo 0 >/sys/devices/system/cpu/cpu3/online". i'm logged on using ssh and after this i get no response. this happens on both xenial and stretch, and on both boards. i haven't tried connecting to the uart yet, but i just wo…

Hello, I am going to make a project using OrangePi (most likely OrangePi Lite, but could be other model) with a camera. So, there is my supplication, for someone to make a test and check HOW MANY pictures (let's say 640x480) can the camera take PER ONE SECOND (working continuously, in a loop)? I am interested in both types of cameras: a USB webcam and OrangePi CAM module. And it's about taking pictures, not a movie. By the way - it is possible to take pictures into RAM? I mean not writing it to SD card. It would improve performance :-) Thanks to everyone in advance!

All, So in this example, let's use SMB, however it does seem to apply to any transport method i use. I seem to have an issue when writing to the Pi whereby the throughput will peak to 50MBps then drop right down and float around 9MBps. <a href="https://ibb.co/fSXXRG"><img src="https://thumb.ibb.co/fSXXRG/write.png" alt="write" border="0"></a> Local disk test shows shows circa 450 Rear and 50MBps write. I get the same results if i make use of the onboard flash or attach an SSD to the SATA port. Does anyone know what's happening here? it's not the source device that is causing this, It appear…

Just for info from cnx-software. Orangepi 3 H6 chip is launched!!!!

Hi I want make VPU work on OPI 3 with mainline kernel I apply the LibreELEC Kernel patch and /dev/video0 is registry. I also apply LibreELEC FFMPEG Patch and build with v4l2-request But when I decode videos,VLC did't decode frames and kernel say's : cedrus 1c0e000.video-codec: Missing required codec control Why? What should I do?

install to SDCard: Armbian_5.89.190626_Orangepi3_Debian_stretch_dev_5.1.12.img update, upgrade install image to EMMC 8GB install lxde (desktop) I rarely have a reset, I think the processor is overheating. Can I reduce the speed without using the fan? (settings debian) for experiments, psensors would be good https://askubuntu.com/questions/41794/how-to-monitor-log-server-hardware-temperatures-load https://oss.oetiker.ch/rrdtool/download.en.html

Hi guys, i dont'understand well mali driver status. Someone can explain me if a working driver exist? And if exist what is best method for build a functional driver? Ive read someting about full mali ddk source that require a license but is not clear if opensouce driver is equivalent or has limitation. I have found: https://developer.arm.com/tools-and-software/graphics-and-gaming/mali-drivers/midgard-kernel If i build this there is some hope to having some kind of accelleration for a normal desktop life like showing wideo with high framerate, Youtube, etc? Thanks in advice Orangepi3 nigtly.

Wi-Fi works → so the problem is only in GPIO / DTB initialization for Bluetooth It worked on the older kernel, but now it doesn't 😞.... Supposedly this is the cause, but is it really? armbianmonitor -u https://paste.armbian.com/uzudezufit

Good evening! Thats my first post, I have for a year a Orangepi 3 LTS that I used for my kid, he looks that never switch off the unit by software and use the switch all the time, so suddenly the unit dont boot anymore, the SD card partition table was corrupt, so I mounted a new OS in another SD but does not boot, the green light is not coming anymore. So I connected a TTL to USB Serial device for debugging and it shows the following information: U-Boot SPL 2021,10-orangepi (Sep 06 2022 - 18:22:23 +0800) PMU: AXP806 DRAM: 2048 MiB Trying to boot from MMC2 NOTICE: NOTICE NOTICE NOTICE: INFOS NOTICE NOTICE: INFO: INFO: INFO? BL31: BL31: BL3…

I tried to set the I2C interface with the armbian-config option but it doesn't work because it writes to the file: armbianEnv.txt .... overlays=sun50i-h6-i2c0 sun50i-h6-i2c1 sun50i-h6-i2c2 and it didn't work on my OrangePi3LTS and it doesn't start the i2C service on startup? but when I enter it manually: overlays=i2c0 i2c1 i2c2 then the i2c service works with my 40x2 LCD 🙂 ...is this a bug and if so can it be fixed? is the option: armbian-config still compatible with my OrangePi3 LTS?

Does anyone use an infrared remote control with the Lirc / rc6 / mce program..and have a verified configuration? I can't configure the above to work on Orange pi 3 lts But I want the Lirc program and not the ir-keytable 🙂

Bookworm 6.1 kernel Cinnamon terminal is unusable. The terminal screen flickers and the written text blinks with the cursor blink. Occasionally the terminal goes black. I am using an ancient 1024x768 screen. Is this the root cause, or is the terminal broken in Cinnamon?

Hi, I've got a pair of OrangePi 3 LTS boards running the CLI only install of Debian Bullseye with a kernel of 5.15.89-sunxi64 and all the latest updates applied. But when I run the 'top' command, I always see a load of 1.0 or higher. Even when the system is completely idle. I'm running the system of the eMMC, not SDcards. I realize that this is really more of a cosmetic issue, but I was hoping someone had a suggestion on how to fix it. The system is mostly idle, it's a test box or remote management system, so it's not really critical, and the load doesn't go high anyway. Cheers, John

I disabled Armbian kernel upgrades to stay at Armbian 23.11.1 until Armbian 24 stabilizes. Yesterday I unfroze the kernel upgrades to upgrade to 24.2.1. I run: apt update apt upgrade apt dist-upgrade Apt update says All packages are up to date. shows nothing. What did I miss?

Hi all, I'm using an OrangePi 3 LTS with Armbian 23.11.1 bookworm current 6.1.63 xfce installed on a microsd card. Unlike some previous version I tried, now the wifi works correctly. As for the bluetooth, it works... every other time. That is, on one boot it will load, in the subsequent one it will fail, and so forth consistently. I'm not an expert, so if you need some output from some program, please tell me which. By now I can say that when it doesn't work, the bt icon in the systray doesn't appear, however if I try ps aux | grep blue* I find that obexd and blueman-applet are running. And if I launch blueman-manager I get an error dialog sa…

I using the following armbian and kernel: # PLEASE DO NOT EDIT THIS FILE BOARD=orangepizero BOARD_NAME="Orange Pi Zero" BOARDFAMILY=sun8i VERSION=5.38 LINUXFAMILY=sunxi BRANCH=next ARCH=arm IMAGE_TYPE=stable BOARD_TYPE=conf INITRD_ARCH=arm KERNEL_IMAGE_TYPE=zImage Linux 4.14.14-sunxi #1 SMP Thu Jan 25 12:20:57 CET 2018 armv7l GNU/Linux My box have constant kernel dumps in the log: [59763.352618] [<c010db15>] (unwind_backtrace) from [<c010a0d9>] (show_stack+0x11/0x14) [59763.352627] [<c010a0d9>] (show_stack) from [<c0867e29>] (dump_stack+0x69/0x78) [59763.352637] [<c0867e29…

Hi All, Sorry if this has been asked before, I haven't been able to find the answer yet. I wish to configure my OrangePi's (Lite and PC+) such that they power on automatically whenever the power is restored after a power outage without needing to press the power button. I'm not sure where we could configure this as the OrangePi's don't seem to have a bios like a Desktop PC. Dave.

I have an OrangePI h3, I upload the Armbian in the SD card, but independent if the SD card is in or not, the Orange pi always display the both network leds turned on. Therefore I do not know if my problem is related to the SO or any hardware problem.

Hello, Is it possible to get a WiFi-Direct connection from OrangePi Lite to for example smartphone and send a file to it? I mean with not using router. Thanks in advance for every answer!

Hi, I have connected Orange Pi Lite over serial UART, but looks like the default settings are to not output the boot log to serial. You can only see U-Boot messages, then "Uncompressing Linux kernel" and after some time the login prompt comes. What exactly do I need to change/configure to get the classic kernel boot log to serial console? Thanks

Hi, I followed the following link to create encrypted root. However, every time I boot, i don't see any prompt for password. My armbianEnv.txt is following", but nothing display at "Console" (HDMI) or "Serial" (debug 3 pins next to USB port). ~ Has anyone had any success? I did this for OrangePi Lite 2 (64-bit) H6 and no issue. Thanks

I have bought 3 OPi Lite 2 (H6 based) dev boards. Just downloaded the latest Bionic image at the following link: https://www.armbian.com/orange-pi-lite-2/ I understand it's WIP. However, it seems to have issue on booting up. I connected HDMI cable and upon boot up, I could see init info on the screen, then it says, starting Kernel ... , then screen goes no signal, power LED stays RED forever. I read that the current image seems to have issue on HDMI. But it worked with HDMI upon initial bootup, then stopped working. My problem is that without HDMI, how could I edit the WIFI config to have the board connected to my network thus to SSH into the board for fu…

Hello, i've got a problem with my orangepi lite. Here are a few posts about problems with connecting to wifi networks, but my device can't even find wifi networks (with iwlist wlan0 scan ). In my area are multiple access point active. The OS is armbian for OrangePi Lite Version: 5.20. iwconfig shows the chip with no errors. I have tried multiple settings in /etc/network/interfaces and /etc/wpa_supplicant/wpa_supplicant.conf after posts in this forum but nothing is working ...

Hello Folks, sorry for popping up here with a technical problem first thing - but I have some trouble. I have a circuit where an attenuator is connected to PA19. Sadly, the port seems to have a pull up which stays active even when I use wiringPi to set the port to input - in fact, even if I short the pin to low via my Keithley ammeter, it still shows up as high. Re things which I already tried: I tried to reduce the fex file to look like this: [product] version = "100" machine = "orangepi-lite" [platform] debug_mode = 1 eraseflag = 1 next_work = 2 [target] boot_clock = 1008 storage_type = -1 [key_detect_en] keyen_flag = 0 [fel_key] fel_key_max = 7 fel_key_m…

I am building armbian with mainline kernel (4.14.19) on jessie for OrangePi Lite... Sometimes on booting my Pi Lite, the wifi does not work. I cannot create hotspot and connecting to existing networks will not work. A short time after booting I see the following messages in the dmesg log [ 102.077151] sunxi-mmc 1c10000.mmc: send stop command failed [ 102.077184] sunxi-mmc 1c10000.mmc: data error, sending stop command If I remove and reload the 8189fs module I will see the following error in the dmesg log [ 572.371452] rtl8189fs: probe of mmc1:0001:1 failed with error -110 If I don't see the mmc errors after startup (say 5 minutes) the w…

In an effort to enable Bluetooth on the OrangePi (Lite2 | 3) I am stuck at enabling UART1 via overlay. According to the schematics, the AP6255 is connected via UART1 (PG6-PG9) to the H6 SoC but not defined in the dtb. Since there is a dtbo which looks promising at /boot/dtb/allwinner/overlay/sun50i-h6-uart1.dtbo I tried adding an overlay to /boot/armbianEnv.txt - manually and via armbian-config. Both did not work out. In addition, I also tried adding uart1 to the dtb, without success. What am I missing?

LANG=en_CN.UTF-8 I have it+SD card+usb TouchScreen+HDMI Screen which work with http://www.orangepi.org/'s image. I've downloaded https://dl.armbian.com/orangepilite2/Debian_stretch_next.7z,verified the sha256 checksum,burn SD card,verified checksum of SD card... After UBoot, nothing was displayed,but `fdisk -l /dev/sdb` changed -------------------------------- Disk /dev/sdb: 30 GiB, 32220643328 bytes, 62930944 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x16977123 Device Boot Start En…

Can someone please add support for the onboard microphone to armbian for the Lite2?! It is missing in armbian-config, there is no h6-analog-codec.dtbo in /boot/dtb/allwinner/overlay The microphone is wired up the same way as on the other h6 boards. Thank you very much!

Hello, On Orangepilite2, USB3 is recognised as USB2. I have connected multiple usb3 devices and results are same. I tried armbian, orangepi Debian, orangepi Ubuntu! results are same same too. For some reason all OS have same issue. In picture mass storage is USB3 device.

I have a question for more experienced users. Quite a long time ago I built an internet radio based on OrangePi Lite + DAC I think in the I2S interface with the module: PCM5102 ... PCM5102 DAC Decoder I2S -Aliexpress unfortunately the board broke down. I have another model, the aforementioned Pi 3 lts but it seems to be less supported. Can I connect the above-mentioned PCM5102 module to this model? Or maybe buy some other supported model that will work just as well as Pi lite with this DAC model or another? Ps. it would be nice if it had the ability to upload Armbian firmware to emmc flash memory I installed Armbian/Ubuntu on Pi3lts but I get some erro…

Hello, I am using Armbian nightly legacy Jessie 3.4.113 build and it seems Mali drivers are included. Please, How should I set values in boot.cmd and boot.scr to mali HW acceleration work properly? I checked this site http://linux-sunxi.org/KernelArgumentsand tried to place something like "sunxi_ve_mem_reserve=64 cma=96 sunxi_g2d_mem_reserve=64 sunxi_fb_mem_reserve=32" to this file on setenv line but armbian fails to boot. I would like to use HW acceleration in VLC. Thank you.

Hello! when I connect to the OrangePi mini TV / AV, TV wrote "no signal" If you connect to hdmi ok FEX: [disp_init] disp_init_enable = 1 disp_mode = 2 screen0_output_type = 3 screen0_output_mode = 3 screen1_output_type = 2 screen1_output_mode = 11 fb0_framebuffer_num = 3 fb0_format = 10 fb0_pixel_sequence = 0 fb0_scaler_mode_enable = 1 fb1_framebuffer_num = 3 fb1_format = 10 fb1_pixel_sequence = 0 fb1_scaler_mode_enable = 0 [tv_out_dac_para] dac_used = 0 dac0_src = 4 dac1_src = 5 dac2_src = 6 dac3_src = 0 and [tv_out_dac_para] dac_used = 1 dac0_src = 4 dac1_src = 5 dac2_src = 6 dac3_src = 1 [tvout_para] …

Hello, i like to work with 1wire 18b20 sensors on my Oragne Pi one , with the latest Armbian Bionic . root@orangepione:~# uname -r 4.14.65-sunxi In this forum and in the orange pi forum, there are some instructions, but I think they are out of date. 1.edit your /etc/default/cpufrequtils After edit. $ cat /etc/default/cpufrequtils ENABLE=true MIN_SPEED=480000 MAX_SPEED=1200000 GOVERNOR=interactive 2.reboot Edited by nopnop2002 at 2017-8-5 17:10 1.edit your /etc/default/cpufrequtils After edit. $ cat /etc/default/cpufrequtils ENABLE=true MIN_SPEED=480000 MAX_SPEED=1200000 GOVERNOR=interactive 2.reboot 3.driver load sudo modprobe w1-gpio su…

I have just flashed the Armbian Stretch mainline kernel 4.14.y. While booting, connected to a HDMI TV/monitor, I can see the start-up text lines initializing various things and at some point (I think it is "starting kernel"), the display gets heavily corrupted with horizontal lines then it switches to a blank screen. The TV displays that it's a 1080p60Hz mode (should be compatible with the display). Any ideas? https://youtu.be/n4-TSFzBgO4

i just installed Armbian_20.11.6_Orangepione_buster_current_5.10.4.img the software is trying to install a driver and is requesting the linux headers, i tried to install the linux headers but is says E: unable to locate package linux-headers-5.10.4 then i switched to the nightly upgrades in the armbian-config and now is on 5.10.7 also tried to install iand i keep getting the same msj E: unable to locate package linux-headers-5.10.7 any clues with this problem ? thanks http://ix.io/2MjH

I started first with orangepi pc2 (H5) but now trying the same thing on orangepi one (h3) - trying to make ili9340 module work it works flawlesly on rpi with raspbian so the hw module works (and the fb_ili9340 module in kernel talks to it properly) debug info I pulled from rpi pi@octopi:~ $ uname -a Linux octopi 4.14.79-v7+ #1159 SMP Sun Nov 4 17:50:20 GMT 2018 armv7l GNU/Linux root@octopi:~# lsmod Module Size Used by xt_tcpudp 16384 1 iptable_mangle 16384 1 xt_DSCP 16384 1 bnep 20480 2 hci_uart 36864 1 btbcm 16384 1 hc…

Hello, do you guys havea proper device configuration file for crosscompiling Qt apps to Armbian on my opi one? Couldn't find one online and the multitude of flags frankly confuse the heck out of me.

Hi, On upgrading to 5.35 Ubuntu Xenia default 3.4.113 I am unable to get DVI video working, I am presented with a pink screen. Monitor is a 1280x1024 dvi connected via HDMI-DVI converter cable. I am configuring this with h3disp -m 1280x1024 -d. I have rolled back to a 5.30 image and everything works as it should. Possibly a bug? How can I upgrade everything in the distro without breaking the video again? Thanks.

Hello I have an Orangepi One which fails after running for a certain time. In the failed "state" pinging it still works, but SSH connections to the Orangepi or from the Orangepi to the Server via Autossh won't work any more. A PHP application running on it is still working. It looks like the issue is that it winds back the time to something ridiculous. Hard reset with pulling Power fixes this for again a certain time till it happens again. I wrote a script which runs every Minute via Cronjob and logs the current time to a file. Before the rewind already something weird is happening. The cronjob is executed twice on 04.40. I have no idea what is hap…

Hi gurus! I'm trying to connect gc2035 camera to my OrangePi One, it's marked as SH-2035 at the cable. It is old problem, as I understand reading forum, but nothing to help me. I'm new Linux user and use Armbian 5.31, Linux orangepione 3.4.113-sun8i #18 SMP PREEMPT Thu Jun 15 02:16:06 CEST 2017 armv7l armv7l armv7l GNU/Linux. That camera works with Armbian 5.20, but I don't want to do downgrade. As I understand it needs to do right initialisation of camera in script.bin or rc.local, but what exactly?? This is part of configuration in my script.fex file: [csi0] vip_used = 1 vip_mode = 0 vip_dev_qty = 1 vip_define_sensor_list = 0 …

Hello, I'm a new Armbian user of my first OrangePI One H3 board after much time spent on rpi boards. I was curious to see how these boards run and I bought one. I'm using a fast 32GB A2 microsd, an external 4 USB externally powered hub, an HDMI to VGA converter with audio out. I was deciding at first which o.s. to use cause I've seen there're also Ubuntu and Debian official 5.x kernel based images on their page but I tried this at first. I've installed usual applications browsers office apps mail etc, and now I'd like to make some questions to better understand some things: 1) I know being on the armbian forum I'd expect everyone to prefer thi…

Hello, I am the owner of this board. I have some questions for developers 1. when will the reboot fix and what is the problem? 2 after last upgrading to 5.59.180904, armbian is no longer loaded at all. log the error: [ 2.319975] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.18 [ 2.328255] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.335488] usb usb5: Product: MUSB HDRC host driver [ 2.340462] usb usb5: Manufacturer: Linux 4.18.5-sunxi64 musb-hcd [ 2.346562] usb usb5: SerialNumber: musb-hdrc.1.auto [ 2.351855] hub 5-0:1.0: USB hub found [ 2.355641] hub 5-0:1.0: 1 port detected [ 2…

Hello. Good day. I'm trying to use the SPI on a OragenPI One Plus (Allwinner H6), and, although I have enable it via the /boot/armbianEnv.txt configuration, communication is not working. Here's the armbianEnv.txt armbian@orangepioneplus:~$ cat /boot/armbianEnv.txt verbosity=1 bootlogo=false console=both disp_mode=1920x1080p60 overlay_prefix=sun50i-h6 rootdev=UUID=19c1886e-0b74-45b8-b9f5-5fbd4bdeb5c2 rootfstype=ext4 overlays=spi-spidev param_spidev_spi_bus=0 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u And here's the SPI device listed under /dev armbian@orangepioneplus:~$ ls -la /dev/sp* crw------- 1 root root 153, 0 nov 28 15:…

Hi, I have OPi One Plus (H6) and I didn't find a way to access/control the GPIO's and the UART in the 26Pin connector. Is there a drivers release or a way to do it. thanks, Yohay

Hey there, I have two questions and one of those may be pretty dumb, but anyway. What is the issue that the onboard network is disabled at the moment? The other question is about the tested 3rd party hardware which include various LAN and WLAN adapters. Have those indeed tested with the current experimental images and working? Or is the network support disabled in the current builds at all? Best regards Werner

https://pastebin.com/jpG4iGtX Not sure what else more to say. I included the whole upgrade process including the restart in the paste above. I'll now prepare another sd card using a fresh nightly image and check if this boots normal or if nightly is currently broken at all. Edit: Yep. Current nightly is broken. Pretty much the same errors https://pastebin.com/pGAG1iUy Armbian_5.51.180708_Orangepioneplus_Debian_stretch_dev_4.18.0-rc3 Edit2 Armbian_5.51.180706_Orangepioneplus_Debian_stretch_dev_4.17.4 confirmed working.

Hi, I thought instead of waiting for mainline kernel support for these boards, if it would be possible to use Allwinner H6 BSP 4.9.56 kernel? Found at https://github.com/Allwinner-Homlet/H6-BSP4.9-linux I am able to compile it on Sunxi's Ubuntu 16.04 Beta image, however from the serial output it seems to at least have trouble with the sd card initializing. I tried to copy over the sd card information in sdmmc@04020000 from Sunix's own /boot/orangepi/OrangePiH6.dtb into Allwinners sun50iw6p1.dtsi but the boot only went a little further ending in a similar kernel panic to when I used the the BSP4.9 with Sunxi's original OrangePiH6.dtb. I am not very skil…

Hi, I was wondering if anybody has managed to get rf433 receiver or emitter to work on an orangepi one ? I am trying to get this pi-switch (https://github.com/lexruee/pi-switch-python) to work. I have installed WiringOP and orangepi_PC_gpio_pyH3. I managed to get pi-switch to compile (i had to add a swap file since it was using so much memory) when i run a sniffing code i get this "wiringPiISR: unable to open /sys/class/gpio/gpio0/value: No such file or directory" Maybe there are some rf433 lib that already work with hte orangepi, not sure, i did not find any ?

Hello, I can't boot my new OrangePi One v.1.1. I have used various SD cards including Sandisk Ultra 32GB. On the serial console I every time see: U-Boot SPL 2018.05-armbian (Oct 26 2018 - 22:09:12 +0200) DRAM: 512 MiB Trying to boot from MMC1 MMC Device 0 not found spl: could not find mmc device. error: -19 SPL: failed to boot from all boot devices ### ERROR ### Please RESET the board ### Power supply is 5V 3A. Ethernet is unplugged and nothing is connected to USB. What I tried: - Flashed on two different computers (MAC and Windows) - used both etcher and dd - checked cards with h2testw for errors (…

Just cancel the topic please. armbianmonitor.log.tgz

Well a little info, I've been using my orangepi one with an SDR dongle to track airplanes with flightradar24 for the last few months. My intentions were to use a POE adapter and run the board outside near the antenna at one point. I have now received the final parts and went to move it today. It has been running flawlessly for a month with my POE adapter off of a switch near my PC in my shop. I now plan on connecting it to the main switch on my LAN. So previously my setup was: Router -> switch -> long ethernet to shop -> swtich -> orangepione now I want to run it: Router -> switch -> long ethernet to outside -> orangepione But for some reason…

Hello, I have read a lot of posts, but I can't control the gpio pins on my orange one+ (Armbian buster-Linux 5.4.28-sunxi64). Currently I open/close the gate and other doors of my home through my Rpi 2 gpio and a 8 relay module, I would like to replace this with the opi, but I can't find the way. Could you help me? Thanks, Marco

Hi Is there any chance to force OrangePi PC to use 1920x1200 resolution? There's no such mode in h3disp. I tried to modify h3disp script but no luck. 1080p60 -d works well, but it's wrong aspect ratio. Please help.

Hello, Is a native 240p timings/resolution possible from the OrangePi PC via the A/V jack? I'd like to use it hooked up to a nice CRT for emulation.

Hi, I have orangePI connected over HDMI to my TV but there is no video. If I connect orangepi with HDMI to DVI (to my monitor) the video is present. Can someone tell me what is wrong or how to set it up? The TV is Panasonic Viera (I have found similar question here: https://www.reddit.com/r/raspberry_pi/comments/5j89dk/having_trouble_with_hdmi_using_rasplex_and_a/) regards Peter

As per the title, I am using the 5.05 Jessie Server image on a OrangePi PC. Every time I shut it down (shutdown -h now) when I power it back up I get errors reading the SD card and it wont boot. I have tried 3 cards, all with the same issue, I can reboot the device with issue and a fsck is clean after every reboot. I do not have a linux machine to scan the card after a power off, so can't check it after it fails. Does anyone have any ideas?

Hello; My OrangePi PC HDMI port is dead, it throws no input signal, and I've read that this board has no ESD protection for HDMI, so I assume it died because of it. What I want to get is video working through analog TV out, but I can't seem to find the solution for this. I guess it should be simple task, but I never did it before. Hopefuly somebody can give me the solution. Thanks!

Hello, I`ll try to hook up display to OpangePi PC, But have no output. My English is not native so i`ll try to write in simlpe way. image Armbian_23.8.1_Orangepipc_jammy_current_6.1.47_minimal.img.xz my dts: /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { target = <&spi0>; __overlay__ { status = "okay"; // cs-gpios = <&pio 0 9 0>,<&pio 0 8 0>; /* PA9=CS0 for LCD, PA8=CS1 for touch */ display: display@0 { compatible = "ilitek,ili9341"; reg = <0>; pinctrl-names = "default"…

Hello, to all OrangePI PC enthusiasts. Well I'm in the community of those who definitely underestimated the Orange of the PI, but let me share my burden :-) for the fun of it. It started with the camera- gc2035 and vfe_v4l2 modules. Had to try a couple of images until I got it by luck I guess - after that I found out that every image I use is not capable of having a FTDI device connected to "ANY" USB Port (OK, you got me, I didn't try the microUSB and I won't). After that I tried no matter what I wanted to connect to USB it was not even recognized. Now I'm back in changing/swapping around Images until I found one that let me plug anything I …

Hi, i am running armbian stretch on an OrangePi PC with "-dev" kernel and uboot. This was originally an jessie installation with legacy kernel, that was upgraded. I'm wondering now, why the cpu frequency only scales between 648 and 1008 MHz instead of 408 and 1296 MHz. Is this to be expected? cpufrequtils is configured to the latter. # lscpu Architecture: armv7l Byte Order: Little Endian CPU(s): 4 On-line CPU(s) list: 0-3 Thread(s) per core: 1 Core(s) per socket: 4 Socket(s): 1 Model: 5 Model name: ARMv7 Processor rev 5 (v7l) CPU max MHz: 1008,0000 CPU min MHz: …

Hi, I installed the desktop focal version of armbian in orange pi pc. It boots correctly but after install lvm2 and restart, it does not boot. If I don't restart the orangepi the lvm volumes works fine, but after reboot or shutdown it not boot. The steps I made: Install on sd with ubuntu (restore image directly). Start the orangepi pc. That's work. sudo apt-get update sudo apt-get upgrade sudo shutdown -r now Here it works and boot correctly: sudo apt-get install lvm2 sudo shutdown -r now Here dont boot the orange pi: The log in serial console is: ***************************************************************** …

Hi there # uname -a Linux orangepipc 3.4.113-sun8i #28 SMP PREEMPT Thu Feb 2 02:01:28 CET 2017 armv7l GNU/Linux #apt-get install pciutils-dev pkg-config #git clone https://github.com/flashrom/flashrom.git #cd flashrom #make CONFIG_INTERNAL=no CONFIG_RAYER_SPI=no CONFIG_NIC3COM=no CONFIG_GFXNVIDIA=no CONFIG_SATASII=no \ CONFIG_ATAHPT=no CONFIG_DRKAISER=no CONFIG_NICREALTEK=no CONFIG_NICNATSEMI=no \ CONFIG_NICINTEL=no CONFIG_NICINTEL_SPI=no CONFIG_OGP_SPI=no CONFIG_SATAMV=no No work! hooked: spi_mosi = port:PC00 spi_miso = port:PC01 spi_sclk = port:PC02 spi_cs0 = port:PC03 root@orangepipc:~/flashrom# ./flashrom -p linux_spi:dev=/dev/spidev0.0 flashrom v0…

Hi, am new on orangePI, Hope my question is not to dumb. I am using the Armbian_5.05_Orangepih3_Debian_jessie_3.4.110.raw image. Kernel is Linux orangepipc 3.4.110-sun8i #18 SMP PREEMPT Tue Mar 8 20:03:32 CET 2016 armv7l GNU/Linux I want to access a serial device connectet to the pins 8 and 10 on the GPIO connector, described at uart 3. /dev/ttyS0 is the 3 connector pin close to the power plug. there is no /dev/ttySn with n>0 and the /dev/ttyGSn are also not the ones to use. How can I create the right device? Same about the IR receiver, Is there any device that represents the IR receiver? Are there modules to load? thanks a lot for help

Hi, I have a project to do and this consists of: Arduino board which work as frequency counter and OrangePi PC which will be some kind of server (mysql, python). The idea is to use UART port to communicate (send / recevie) datas from arduino to OrangePi using C, Java or python.. Here is my schema using LLC (converter between arduino and orangePC) (hope this will work ) Is there some example in C, python or java on how to use GPIO UART pin 8/10 on orangepi as serial port? For now I have installed library from: https://github.com/zhaolei/WiringOP and second for python from: https://github.com/duxingkei33/orangepi_PC_gpio_pyH3

OrangePi PC H3 UsbTV kernel driver causes complete system freeze on Armbian OrangePi PC kernel 4.14. Did anyone observed similar issues? I already reported a bug against the USBTV repo, but not sure if this is the right place. [Update: After quick response of Federico Simoncelli from the USBTV repo, I reported this bug to the kernel bugzilla as a new bug there] On x86_64 platform it works well. Is it the bug of Armbian or USBTV?

I use mpv in Armbian 5.10 on a OPiPC, HDMI attach to my audio and TV . I checked the audio devices at first: mpv --audio-device=help List of detected audio devices: 'auto' (Autoselect device) 'pulse/alsa_output.platform-audiocodec.analog-stereo' (audiocodec Analog Stereo) 'pulse/alsa_output.platform-sndhdmi.analog-stereo' (sndhdmi Analog Stereo) 'alsa/default' (Playback/recording through the PulseAudio sound server) 'alsa/plughw:CARD=audiocodec,DEV=0' (audiocodec, /Hardware device with all software conversions) 'alsa/plughw:CARD=sndhdmiraw,DEV=0' (sndhdmi, /Hardware device with all software conversions) 'oss' (Default (oss)) 'jack' (Default (jack)) …

Hi, I tested my board with below armbian distro. Question is , there are lots of entry about H3 hw decode problems, are these fixed in this distro? When i open 1080p mp4 Big Buck Bunny video still doesnt work is that any specific settings to work with hw accelerated decode. How can i be sure that hw decoding is running with VLC? or any specific ffmpeg command. Linux orangepipc 5.10.60-sunxi #21.08.1 SMP Wed Aug 25 18:19:32 UTC 2021 armv7l armv7l armv7l GNU/Linux I tested video with - VLC using 55% cpu - MPV using 40% cpu Umit

I'm running an OrangePI PC with legacy Jessie server and armbian 5.23 and kernel 3.4.112. I never seen the ouput through the HDMI monitor. It's always without signal, even at boot when uboot start. Is that normal ? I played with h3disp, but it never work. I would like to see just the boot and the text console. Any suggestion ? Thanks

Dear experts, I would like to make my OrangePi PC on board LEDs works like power (Green: Default ON) and status (Red:heartbeat blinking). root@orangepipc:~# ls -1 /sys/class/leds/ orangepi:green:pwr orangepi:red:status root@orangepipc:~# Any experts can assist me on this matter on edit in /etc/rc.local to get it works. Thanks in advance and appreciated your help. Regards, Sai Hou

Hi folks! I'm a proud owner of 120 Orange Pis. Now I want to do git deployment and reboot the device. I've enabled the ttyS3 for serial connection. Now I want to reboot the device. Sadly enough the device shuts down when executing a reboot or "sudo init 6"command. And when I type shutdown, the device is still on. I've search all kinds of forums, but I cannot find a suitable fix for this. Thanks in advance!

need help to drive Orangepi pc plus with waveshare 3.5inch display with xpt2046 touch driver. OS:- Armbian 22.11 Jammy XFCE Desktop version Kernal :- Kernel 5.15.y link for the os :- https://www.armbian.com/orange-pi-pc-plus/ link for display :- https://www.waveshare.com/3.5inch-hdmi-lcd.htm can any one help to drive touch screen you can message if you need more information,

I have tried the image for Buster from the Download page for OrangePi PC Plus, and also built new images from current Git repo. In all cases the device bootloops when it tries to start the kernel. The image from the OrangePi website works ok. This looks like a similar issue as experienced recently with CubieTruck and BananaPi A20 boards (https://armbian.atlassian.net/browse/AR-749) which was fixed with a workaround (https://github.com/armbian/build/pull/2963) Is it possibly the same / similar underlying problem?

Just as the title says. I have taken the current version of debian armbian from the archives, flashed this onto a micro sd card and then installed the mainline kernel packages over this. It boots to a login prompt, but after a few seconds the whole system locks up. Does anyone have any idea what coudl cause this?

Good day, for my Orangepi PC+ I installed Armbian Ubuntu Jammy on a µSD card. Up until Armbian Ubuntu Strech I was able to use a PCM510A for sound output. The settings for this were easy. With all updated OS after Strech, I can't install the PCM. Unfortunately, the help that was published in the forum wasn't helpful or I couldn't take it over. On the eMMC I have installed Armbian5.59 Orangepipcplus Ubuntu xenial default 3.4.113 desktop. Because of the advanced age of this OS, there are no updates and upgrades. Luckily my internet radio still works. Can someone explain to me how I can install the PCM510A at Jammy? Kind regards hajupiko49

6.960880] zram1: detected capacity change from 0 to 506638336 [ 7.108492] asoc-simple-card soc:sound: i2s-hifi <-> 1c22800.i2s mapping ok [ 7.821162] random: crng init done [ 7.821171] random: 7 urandom warning(s) missed due to ratelimiting [ 7.897054] Adding 494760k swap on /dev/zram1. Priority:5 extents:1 across:494760k SSFS [ 7.995324] zram0: detected capacity change from 0 to 52428800 [ 8.134498] EXT4-fs (zram0): mounted filesystem without journal. Opts: discard [ 11.299194] dwmac-sun8i 1c30000.ethernet eth0: PHY [0.1:01] driver [Generic PHY] [ 11.299222] dwmac-sun8i 1c30000.ethernet eth0: phy: setting supported 00,00000000,000062cf advert…

Hi, Is there a way to fix emmc booting problem from uboot itself, i've updated armbian and now orangepi pc+ doesn't boot, i've connected uart and i see that it reads /boot/boot.scr from mmc 1, but then tries to load stuff from mmc 0, so i guess my boot.scr got overwritten by default one .. or something. boot shows this => boot switch to partitions #0, OK mmc1(part 0) is current device Scanning mmc 1:1... Found U-Boot script /boot/boot.scr 3565 bytes read in 6 ms (580.1 KiB/s) ## Executing script at 43100000 U-boot loaded from eMMC or secondary SD Boot script loaded from mmc MMC: no card present ** Bad device mmc 0…

Hello everyone, Is there any utility to deal with overscan when using TVout? I'm using Armbian Legacy kernel. There is a tool called Allwinner_TVOUT_manipulator, anyone have used it?

OrangePI PC2 Problem report of the current state and improvement favor. --------------------------------------- Armbian_5.40_Orangepipc2_Ubuntu_xenial_next_4.14.15_desktop Keyboard and the monitor resolution.. other All kinds' setting, reboot, when, everything goes off. Therefore it isn't used. --------------------------------------- Armbian_5.34.171121_Orangepipc2_Ubuntu_xenial_next_4.13.14_desktop A keyboard is the monitor resolution only. It's preserved and it's practicable somehow. (1) Setting of other than above, reboot, when, please disappear. I close. (2) Cash of Root becomes full right now, even Mozc, install, can. ---…

CONFIG_BTRFS_FS_CHECK_INTEGRITY is not enabled in config. When I tried to enable it in the armbian build system, I saw the word "DANGEROUS". Is this an unstable (or dangerous) feature ? Should I enabled it and use it ? if not, how to ensure data integrity ?

My RPi PC2 was flashed the armbian OS which was downloaded from the main page ARMBIAN about 3 months ago. Yesterday, I found some packages update are available with "apt update". So I did the command "apt upgrade" . But from then on, the board never be boot up. From the console, the U-Boot version has been upgraded to 2017-09-rc4 from the old version 2017.01-rc1-g5df570f-dirty. I'd appreciate it if anyone could help with this or give me some suggestion. U-Boot SPL 2017.09-rc4-armbian (Sep 11 2017 - 03:34:11) DRAM: 1024 MiB Trying to boot from MMC1 NOTICE: BL3-1: Running on H5 (1718) in SRAM A2 (@0x44000) NOTICE: Configuring SPC Controller N…

Hey guys. I have been trying to utilize H5 vpu decoding for 10+ hours... Still no go. Here is the checklist: kernel Using mainline kernel 5.8.9 from Armbian/build current. `uname -a` output: All kernel configs needed on Sunxi-Cedrus homepage were added, cma set to 256M. libva-v4l2-request Using https://github.com/Sash0k/libva-v4l2-request master. Compiled and make installed. `vainfo` output: `v4l2-ctl --list-formats` output: `./v4l2-request-test -f 25 -l` output: Cpu usage is quite low(4 cores <5%), checked with lsof and…

Hi...Is support for using Mali GPU of Orangepi PC2 enabled for armbian? I'm trying to install the mesa-dri utilities and getting stuck in the libc-bin segmentation fault? Is it because of lack of support or something else? Also I'm getting issues of protobuf while compiling Opencv for Orangepi PC2. If anybody can help!!

I will use a orangepi PC2 as openhab server. Arbian 25.2 kernel 6.6.62 minimal.img is installed. The orangepi is connected with an ethernet cable to the router, but is not visible in the list of connected devices. So I suppose he does not make connection. I want to access the orangepi by putty on my PC but as long he is not online, connection is not possible. Led's on the ethernet connector ar flashing. What do I wrong ?

Wanted to share my very positive experience upgrading to the latest kernel. Followed the procedure using armbian-config and it worked out of the box on my OrangePi PC2. Left the system overnight running my standard tests and no issues. Even the problematic rtl8192 has no issue. There used to be a slight judder on the HDMI attached monitor that is gone now, perhaps due to the new MALI450 gpu modules. ___ ____ _ ____ ____ ____ / _ \| _ \(_) | _ \ / ___|___ \ | | | | |_) | | | |_) | | __) | | |_| | __/| | | __/| |___ / __/ \___/|_| |_| |_| \____|_____| W…

Hello, Using Armbian 20.02.1 Buster Image: Armbian_20.02.1_Orangepiplus_buster_current_5.4.20 Kernel: Linux orangepiplus2 5.4.28-sunxi #20.02.7 SMP Sat Mar 28 14:32:15 CET 2020 armv7l GNU/Linux. USB devices can't be detected. I tried with my bluetooth dongle, usb storage drive. None of them works. lsusb -t /: Bus 04.Port 1: Dev 1, Class=root_hub, Driver=ehci-platform/1p, 480M |__ Port 1: Dev 2, If 0, Class=Mass Storage, Driver=usb-storage, 480M /: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=ehci-platform/1p, 480M /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M /: Bus 01.Port 1: Dev 1, Class=root_…

Hello, Is there anyone that has problem with USB keyboard on armbian 20.11.9 buster. I have tried both 20.11.6 and 20.11.9 buster nut the keyboard can't be recognized in armbian. (caplock, numlock LED don't work as well) I tried 4 USB ports on the port but doesn't work. The keyboard is working fine with my Windows PC. Thanks

Hello, since the build for OrangePi Plus 2 is only community maintained (and there is a warning during installation that this build is not suitable for production), I though of using some generic image or a image for a similar board with standard support. Is it a good Idea? Which image should I choose? Thanks for help, Skalistan P.S. there is no tag for "OrangePi Plus 2", so I used the tag for "OrangePi Plus 2E" since it is required to add a tag.

Someone can help me with detail instruction: how I can enable touchscreen trough gpio on OrangePi Plus 2. Screen setup to 800x480 but cant enable touch, because I am beginner.