Allwinner sunxi

Hi there, I do no need help how to sort it out. This is only report for Igor. I installed Jessie server image with legacy kernel on my Cubietruck few on April. I decided try upgrade to vanilla kernel about two weeks ago with command see below. And today I decided return back to legacy kernel with same command. (it is not important why but I have answer for it, I am enjoying testing ... ;-) ) ... but before I rebooted my experiencies say check /boot folder and I did not find important files there. I used command: wget -q -O - http://upgrade.armbian.com| bash And here is output of log: cat /boot/upgrade.log No packages will be installed, upgraded, …

Hi, I want to use my cubietruck to play the video in HD and with spdif pass-trougth and I want use mopidy. with last armbian jessie desktop : with mplayer2 : pass-trougth is ok but video is too slow with mpv : I heard a very loud noise at the output of the amplifier is not DTS decoding and is transmitted as the pcm.--> it is a kernel problem: the driver sends a sound that is not recognized by the amplifier. the SPDIF sound format is limited to 24 bits video is OK. mopidy is OK with last armbian xenial: it work because mpv is very old with mplayer2 : pass-through and video is ok but kernel panic when I put the video paused--> kernel bug solved : …

This simple tutorial to explain ho wto manage the GPIO with the I2C bus and C++ under Netbeans .

Verify kernel 4.6 with dev on test construction Armbian where the CPU is not recognized correctly. root@orangepipc:~# lscpu Architecture: armv7l Byte Order: Little Endian CPU(s): 4 On-line CPU(s) list: 0 Off-line CPU(s) list: 1-3 Thread(s) per core: 1 Core(s) per socket: 1 Socket(s): 1 Model name: ARMv7 Processor rev 5 (v7l) [ 0.001455] CPU: Testing write buffer coherency: ok [ 0.001769] /cpus/cpu@0 missing clock-frequency property [ 0.001784] /cpus/cpu@1 missing clock-frequency property [ 0.001794] /cpus/cpu@2 missing clock-frequency property [ 0.001805] /cpus/cpu@3 missing clock-frequenc…

I upgraded a cubieboard2 to kernel 5.11 and noticed that I have one core online and one core offline. Can someone confirm that?

hi guys, im trying to compile media_build but it says the kernel has no i2c mux support how could i easy compile a new kernel with i2_mux enabled on the orange pi?

Hi! I've tried to compile the lwjgl lib on my opiplus2, but I'm stuck on ant compile_native_es. ant jars_es finished successfully. The error: [apply] /usr/bin/ld: cannot find -lEGL Tried to install libegl1-mesa-dev package but it conflicts with the mali driver package. Is it possible to compile the lwjgl with opengl-es on the opi, or that's a dead idea? Thanks in advance!

I'm buying WiFi Dongle RTL8188 and want create WiFi AdHoc (WEP) connect PC<->OrangePi PC HowTo settings on Armbian? i'm install sudo apt install network-manager-gnome after try connect to wifi adhoc (WEP) from network-manager (nm-applet), show error: (32) Not authorized to control networking My settings: userous@orangepipc:~$ groups userous dialout sudo audio video plugdev netdev cat /etc/network/interfaces auto lo iface lo inet loopback

Hi, I am trying to used Wifi on my Cubietruck, but I cannot get it running. Running Armbian Jessie 4.2.3 (Armbian_4.5_Cubietruck_Debian_jessie_4.2.3 - freshly installed), I changed /etc/network/interfaces according to the comments. # Wired adapter #1 auto eth0 iface eth0 inet dhcp # hwaddress ether # if you want to set MAC manually # pre-up /sbin/ifconfig eth0 mtu 3838 # setting MTU for DHCP, static just: mtu 3838 # # Wired adapter #2 #auto eth1 # iface eth1 inet dhcp # hwaddress ether # if you want to set MAC manually # pre-up /sbin/ifconfig eth0 mtu 3838 # setting MTU for DHCP, static just: mtu 3838 # # Wireless adapter #1 au…

I finally decided to give armbian a try on my Orange Pi One. Started without any issue and then I noticed that the 50°c idle. Sounds a bit high. I compliled mplayer with j3 and saw the temperature reaching 90°c then throttling down the frequency to 600MHz with a temperature of 70°c. Ultimately this board is nowhere faster than a RPI2 if it is stuck to 600MHz under heavy load. Or my Orange PI One has a serious problem. Any advice?

[This is a repost of my own post at orangepi.org.] Hi, I'm very excited to use the Armbian on Orange Pi One. Without rebuilding a kernel or fex file, here is how to configure the Orange Pi One governor so the "[ 150.135554] [cpu_freq] ERR:set cpu frequency to 648MHz failed!" and "[ARISC ERROR] messages no longer appear in dmesg. We will set it to 912MHz on the low end and 1200MHz on the higher end which scale up and down properly on the Orange Pi One. This is until you update your fex file and/or kernel config to use different values for the CPU frequency scaling that are a little different on the Orange Pi One than they are on the Orange Pi PC. Put it in your /e…

Hi, I use my cubietruck with xenial desktop and mopidy. I installed successfully mopidy with mopidy's repository I tested only with alsa then with pulse. results : no sound and error on service mopidy status. pulse work well with mpv. Can you help me?

I have a orange pi pc (H3). I connected a thermal printer which has a TTL interface so I connected the TX wire from the printer to 8 and RX to 10 to orange pi. I change the serial port in my script to /dev/ttyS0 and tried a test print but it will not print. I have tried this in raspberry pi 2 and it works. Any tips how to connect the thermal printer to orange pi.

Hi, I'm trying use USB Audio card it's works fine in this cammand aplay -D hw:2,0 test.wav hardware Orange pi one version Armbian 5.11 root@orangepione:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: audiocodec [audiocodec], device 0: SUNXI-CODEC sndcodec-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: sndhdmi [sndhdmi], device 0: SUNXI-HDMIAUDIO sndhdmi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 2: Audio [USB Audio], device 0: USB Audio [USB Audio] Subdevices: 1/1 Subdevice #0: subdevice #0 use portaudio library and get this error root@orangepione:~/portaudio/bin# ./paex_sine PortAudio Test: output sine wave. SR…

Goodmorning, I've upgraded my Orange Pi-PC to 5.11 Upgrading process OK then rebooted. Now PI continue rebooting (leds turn on as usual but after a while they turn off) and i'm not able to access it. Have you any advice? is there a way to reset it? thanks in advance

hello everyone ! How to get totally permission in /root folder of my orangepiplus2 under armbian? I have already set sudo su ----pass ok I'm installing WiringOP and I have to go inside /root Using psw I know the path that is /root/WiringOP Then I type chmod +x /.build and then /.build but I don't have permission . Opening the file system I see the "X" over the root folder Could I have the totally control of armbian ? Thanks !

Hy everyone, I am desperately trying to get armbian running on a bananapi pro. By using the raw files i had no luck. Did anyone ever try wether it works at all? For me id does not even boot... Thanks

Hy everyone, I am trying to get armbian running on my bananapi. The problem is if i write the raw file to the sdcard (following the instructions) no boot partition is created. The bananapi does panic while booting and restarts after a few seconds... Any ideas? Thanks!

if anyone is interested https://github.com/igorpecovnik/lib/issues/311

Hello, I'm testing the latest (kernel 4.5) jessie server vanilla on a Olimex Lime2. If a battery is connected to the board and the power plugged in, the board start by itself ! I would like to change this behavior, is there any file to tweak ? Thanks

Hi, Since latest update just a few days ago (Linux bananapi 4.5.5-sunxi) , the bananpi keeps telling me this: [ 5 updates to install: apt-get upgrade] . When i try to upgrade there arent anything to upgrade. In did apt-get update and apt-get upgrade and nothing to upgrade. I manually execute /etc/update-motd/40-updates and its true that it says that there are 5 updates. So there must be something there that its not chaning. Any tips on this? EDIT: ok i just fixed this by manually editing the file /var/cache/apt/archives/updates.number and setting it to 0 but i think this should be automatic and it wasn't working for some reason. (seemed like the script wasn't updatin…

On a CB1.... cubie@cubieboard:~$ uname -a Linux cubieboard 4.5.2-sunxi #11 SMP Thu Apr 28 21:53:25 CEST 2016 armv7l GNU/Linux cubie@cubieboard:~$ lsb_release -a No LSB modules are available. Distributor ID: Debian Description: Debian GNU/Linux 8.4 (jessie) Release: 8.4 Codename: jessie cubie@cubieboard:~$ ... I'm trying to use the gpio pins I set up in script.bin with this configuration: No other peripherals are using those pins that are configured in my fex file. A scan of the DTS file also shows nothing using those pins. When I enable pin 1 via: the gpio1 device shows up. When I do the network interface stops communicating. The sy…

Hi! I have an OPiPlus2, the official product page says that the soc runs on 1.6ghz, but the cpufreq-info says it's hardware limited to 1.3ghz, so what now? Thanks in advance and sorry if I miss something!

Hi I have added the serial monitor (because i had some trouble booting up) I can see the booting proces of the U-boot. If i'm looking in the log, i see a few file not found entry's: ** File not found /boot/.verbose ** ** File not found /boot/.next ** ** Unrecognized filesystem type ** ** File not found .next ** I did not see these files in the /boot directory either. Can i change something to get ride of these messages. Thx The complete startup log on OrangePi plus with armbian for orangepiplus: === U-Boot SPL 2016.03-armbian-sun8i (Apr 30 2016 - 23:26:36) DRAM: 1024 MiB Trying to boot from MMC U-Boot 2016.03-armbian-sun8i (Apr 30 2016 …

Hi to All, I have just tried to compile Armbian after a few days pause and get error in: │ LD [M] drivers/usb/serial/usbserial.o │ │ LD drivers/usb/built-in.o │ │ LD drivers/built-in.o [ error ] ERROR in function compile_kernel [ common.sh:188 ] [ error ] Kernel was not built [ @host ] I test different ways including previous kernel branch (4.5.4). Even starting from scratch was with no success. Where could be a problem? Best regards Chris

Does anyone have a countermeasure using Onboard Wifi of Orange Pi Lite?

Hello guys, apparently there is a new product in the orangepi lineup. It is the PC+ (PC Plus), which has 8gb EMMC and a Wifi chip onboard. The rest of the features seems to be the same as the plain OrangePI PC. The new SBC can't be found on the orangepi official site, but it is available on aliexpress: http://www.aliexpress.com/store/product/Orange-Pi-PC-Plus-ubuntu-linux-and-android-mini-PC-Beyond-Raspberry-Pi-2/1553371_32668618847.html

Hi. My board is Orangepi-PC Allwinner H3. I had wifi-dongle-usb problem.. so i used armbian.. I was download Image here http://www.armbian.com/orange-pi-one. I confirm wifi dongle is working! But Uart3 in not working.. I need uart3 for Bluetooth module.. I can't find ttyS3 in /dev/.. so i used source at https://github.com/igorpecovnik/lib I built two image.. -> Armbian_5.11_Orangepipc_Debian_jessie_4.6.0_desktop -> Armbian_5.11_Orangepipc_Debian_jessie_4.6.0 but both not working... I can see green led but i can't connect ssh... and cant' show console by monitor.. How can i do? Please help. Thanks.

Little question: i did an apt-get upgrade with latest armbian 5.11, there linux-u-boot-orangepiplus_5.11_armhf was installed automatically. Did i have to write u-boot-sunxi-with-spl.bin manually to partition with dd? And if yes, to which partition (armbian is installed to emmc, i have mmcblk0p1, mmcblk0boot0 and mmcblk0boot1)? Thx

Hi Igor and all, after running armbian on my A20 lime2 for a long time, I decided to switch to armbian on my A10 lime, too (from jessie with a eewiki-based self-compiled kernel). So far it works as perfect as the A20, but there are two small and funny things with the Armbian_5.00_Lime-a10_Debian_jessie_3.4.110.zip image I used: After login the nice armbian banner stated that my A10 lime is a cubieboard . I have a cubieboard, too. So I double checked... The problem is located in /etc/init.d/armhwinfo, There all "sun4i" boards are simply "Cubieboard". I had to adapt the LED check which is used to detect Lime and Lime2 a bit and added the Lime A10. I ch…

opi pc arm 5.10 ALSA no output from speakers but output only available through hdmi. when installed pulse audio able get and change audio hdmi to analog but when switched to HDMI playback hangs and freezes. Any solution?

Hi to All, I recently upgraded my "test server" to the current version, by flashing a new image to my sd-card. However i forgot to recover some essential files, before flashing! I liked very much the login info about the the number of available updates, since I used the testing repo at that time. Could someone provide the code snipplet for that piece of info ann thell me, in which file to place it?? Well, many many thanks for your help and advice! regards, ireng

Hi, I noticed today that I'm getting those ARISC Errors again. I'm running the 5.05 server version which I ran apt-get upgrade on. I got the same when I tested out the new 5.10 image aswell. (Upgrading to 5.10 3.4.112 or using the new image wont let me compile the 'make scripts' either) [ 1424.305736] [ARISC ERROR] :message process error [ 1424.305763] [ARISC ERROR] :message addr : f004b840 [ 1424.305778] [ARISC ERROR] :message state : 5 [ 1424.305792] [ARISC ERROR] :message attr : 2 [ 1424.305805] [ARISC ERROR] :message type : 30 [ 1424.305818] [ARISC ERROR] :message result : ff [ 1424.305831] [ARISC WARING] :callback not install [ 1424.305849] [cpu_freq] ERR…

I try to use acl but I failed to remount file system with acl if seams kernel compiled with disabled acl for ext filesystem. my fstab config: # UNCONFIGURED FSTAB FOR BASE SYSTEM tmpfs /tmp tmpfs nodev,nosuid,size=256M 0 0 /dev/mmcblk0p1 / ext4 acl,defaults,noatime,nodiratime,data=writeback,commit=600,errors=remount-ro 0 0 /var/swap none swap sw 0 0 and my check for acl in kernel config: root@orangepipc:~# cat /boot/config-3.4.112-sun8i | grep _ACL # CONFIG_EXT4_FS_POSIX_ACL is not set CONFIG_BTRFS_FS_POSIX_ACL=y CONFIG_FS_POSIX_ACL=y CONFIG_GENERIC_ACL=y CONFIG_TMPFS_POSIX_ACL=y CONFIG_NFS_V3_ACL=y CONFIG_NFSD_V2…

Hi congrats for the wonderful job with Armbian, i own a banana pro and I've found a great projet for rasp called Dietpi (http://dietpi.com/), Unfortunately the creator hasnt got a Bpro so he is not able to make it for our board, I'm asking if anyone is capable of making this suitable for us? It would be even more awesome, thank you

Hi guys, I received 5pcs of Orange Pi PC recently. I prepared system for all of them based on 3.4.xxx kernel Jessie sever image. Every board with only wifi connection I cannot reach on network. I have started investigating problem and these Realtek dongles are showing up like 2 devices wlan0 wlan1. Wpa supplicant driver crashed during boot and there is some strange message in startup log about usb. I am at work now so I cannot post it but on development version I tested this morning is that wifi dongle working and successfully connected to network. Sent from my Redmi Note 2 using Tapatalk

Hi, I'm fairly new to linux and I've been trying to get my banana pi OTG port to act as a HID device when plugged in. I've been looking to do it using configfs and usb_gadget but I have no idea how to get this working. Do I need to compile the kernel with additional options to get this working? I've googled for days now and tried various different solutions but not got far with it. Any help is much appreciated.

Hi, guys, great stuff here ! I am testing: Orange Pi One, 8GB SD Armbian 3.4.110-sun8i MotionEye, (great stuff https://github.com/ccrisan/motioneye/wiki) It all is working very well, (only a few resolutions like 1440x960 are usable for now). Much better than the old and too slow RPi1, being replaced But my var/log/syslog is filling op rapidly with warnings about the Orange Pi Camera module. 5-6 lines per second : May 3 23:44:11 OrangePi01 kernel: [ 1713.501813] [VFE_WARN] Nobody is waiting on this video buffer,buf = 0xd38b7c80 May 3 23:44:11 OrangePi02 kernel: [ 1713.742666] [VFE_WARN]Only two buffer left for csi May 3 23:44:11 OrangePi02 kernel: [ 1…

Hello, I do images of Debian Jessie with Desktop anf in the end it do image but I have : [ o.k. ] Installing desktop-extras for sunxi [ sunxi ] E: Impossible de trouver le paquet libdri2-1 dpkg: des problèmes de dépendances empêchent la configuration de mpv : mpv dépend de libbs2b0 ; cependant : Le paquet libbs2b0 n'est pas installé. mpv dépend de libcdio-cdda1 (>= 0.83) ; cependant : Le paquet libcdio-cdda1 n'est pas installé. mpv dépend de libcdio-paranoia1 (>= 0.83) ; cependant : Le paquet libcdio-paranoia1 n'est pas installé. mpv dépend de libfdk-aac0 (>= 0.1.1) ; cependant : Le paquet libfdk-aac0 n'est pas installé. mpv dépen…

How to turn off leds on cubietruck? I use Legacy Trusty server

Hey there, I flashed the nand with phoenix tools and after that successfully installed Armbian from my sd to the nand. Somehow I have no write access on the nand. What do I need to do, to enable write access so I'm able to change config files etc. Beste regards, Eyst

Hi all, I upgraded my jessie 5.05 desktop version for Orange Pi PC via "apt-get upgrade" to 5.10 without any issues. Now I noticed that the green status LED blinks twice every ~0.5s after first reboot. Can anyone figure out the meaning of this?? Thanks in advance.

So, the Linux Kernel 4.6 is out. Supposedly it comes with a lot of new ARM processor support. I'm excited about this. I'm not too knowledgeable when it comes to kernel development, especially with ARM devices. I guess the question is, what's it going to take to move the devices that use these supposedly newly supported chips up to 4.6? I'm somewhat keen on updating to a kernel that isn't approaching EOL.

I tried all 3 versions but they doesn't boot. I tested using Armbian 4.5. It booted correctly. I used Rufus for writing to SD. Is there anything changed for writing? Also does it support LeMaker official lcd at version 5.1? Thanks.

Hello, I have a OrangePi Plus 2. I want to build images of desktop and no desktop. I build Debian and works fine. But for desktop only debian works not ubuntu xenial. It not boot. Also in Desbian when I can add external Button to can start pc with it ? like a real computer ? Tat's normal when i connect to DC it take a time to start ? Thanks

Image: Armbian_5.04_Cubieboard2_Debian_jessie_4.4.3 Board: CubieBoard2 (SD+NAND version) Available platforms: i386 with Debian Jessie (sunxi tools) and PowerMac G5. Before Armbian, I had Cubian installed on an SD card. I saved the NAND root data and all the NAND? sub-partitions, so I have a full image of the original NAND and images of each partition. I took out the card, and inserted a fresh Armbian installation, it boots up quickly and works fine. However, as I wanted to set my CubieBoard2 up so it boots from a S-ATA disk (I bought a 1TB WDC drive), I decided to run nand-sata-install. But I got only one menu item to select, so I cancelled. I then did a cat…

Is there anyone who can give me some examples or description how to work with I/O, SPI, I2C, UART, TCP, and so on in Armbian (for example C code)?

hi i have installed armbain on microsd card on banana pi m2+. Pulseaudio via pavucontrol recognized the sound card. Every seems to be ok. But when i tried play radio via rythmbox or play you tube audio voice is very interruped. it does not work in fact, because interruption are very often..... the same problem is with images provident by banana pi team. Only Raspbian MATE images works out of box.

Hi everyone, I bought an Orange Pi oneas a cheap replacement for the unobtainable Raspberry Pi Zero for a little Emulation project. Right now I don't know if it was the right decision:) I wanted to add a waveshare 3.5" display to the orange pi, but I don't even get there. I downloaded the armbian distribution v5.10 legacy Jessy desktop. After the start of the desktop, icons, the taskbar and open windows disappear at random, icons return but the taskbar does not, The desktop is unusable. A similar problem happens in the console, I don't see the cursor where I'm typing. On the command line, thats acceptable but using an editor like nano I have no idea where I am. …

Hello, In the following environments of Cubietruck, a problem which the CPU core is not recognized only one has occurred. $ hostnamectl Static hostname: dns02.kometch.local Icon name: computer Chassis: n/a Machine ID: 609e2bf4c5884368b36018d67982759e Boot ID: 4faccf729c4042fc87013cb82494b486 Operating System: Debian GNU/Linux 8 (jessie) Kernel: Linux 4.1.6-sunxi Architecture: arm $ cat /proc/cpuinfo processor : 0 model name : ARMv7 Processor rev 4 (v7l) BogoMIPS : 16.42 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm CPU implementer…

Hello, I am facing an issue regarding audio playback using the vanilla kernel( v4.5.2 ) for Banana Pi. There is no sound via the analog audio jack. aplay -l does show my playback device though. Here are some screenshots of my current config: speaker-test is throwing error: Should I need to configure anything else?

Hi there, I've been trying for a few hours now to get the GPIOs working with the mainline kernel (ARMBIAN Debian GNU/Linux 8 (jessie) 4.5.2-sunxi). According to the board layout photo, I am using PG0, PG1, PG2 and PG3. With the legacy kernel, they export as GPIO1-PG0 a.s.o. accordingly and work perfectly. So I calculate the GPIO pin number: G is 7th letter, 7 - 1 is 6, 6 * 32 is 192. GPIO192 exports fine, I can set it to output, change the value to 1 but there's no voltage! Can anyone help me, please?

I want to install debian or armbian or what ever it is for Orange Pi One to be a server. I downloaded Jessie server from here: http://www.armbian.com/orange-pi-one/and extracted the 7z file. I do now know what to do with the raw-files I extracted. At first I tried to install install basic Debian from here: http://www.orangepi.org/orangepibbsen/forum.php?mod=viewthread&tid=342&extra=page%3D1 but I didn't undestand the instructions after mounting SD Card FAT partition. I'm not even sure am I suppose to mount it to Orange Pi or the PC I used to write the image to th SD. So I went looking for another way and found the first mentioned which was seemed to be made …

Hello, I have a Cubieboard2 and armbian in a vanilla kernel with jessie flavor. This board has a 2 cores processor. When I am logging in, load average is shown and becomes red when it is greater than 1.0. Since, there are 2 cores, it should be colorized only when it reaches 2.0. Is it possible to have this feature (taking care of each board's number of cores) ? Thank you

Hi ! Ref : Olinuxino LIME2 4G with new 3.4.112 kernel When installing to NAND, on the console I see a lot of : PHY_PageRead : too much ecc err,bank 0 block 276,page 4 PHY_PageRead : too much ecc err,bank 0 block 276,page 18 and so on ... Sometimes the installation succeeded, sometimes not, but the system is often instable, and finally, fully unusable. I tried all the precompiled images, then I compiled myself, but the same problem ... Until now, I used 3.4.106 without problems Thanks for support ! Greetings ,

Hello, I am really struggling trying to find up to date images (debian jessy) for my Cubieboard4 A80. I'm thinking of selling the hardware now as i'm stuck on the old images which are not being patched: http://dl.cubieboard.org/model/cc-a80/Image/debian-server/ Can you suggest how i should proceed? Any help would be greatly appreciated Thanks, phrag

Hi, What do you do to avoid the problem with zero size files or zeroes at the end after unclean reboot on cubie or another device with nand flash on extx filesystem ? Why do everyone use extx filesystems when its generate these problems ? a little description ... http://www.linux-mtd.infradead.org/faq/ubifs.html#L_empty_file http://www.linux-mtd.infradead.org/faq/ubifs.html#L_end_hole Thanks, ariz

comes to adding 131068 swap on /var/swap and further loading is not How to fix it? tried a USB flash drive to the new record, it is still the same, a reboot is not helping

http://arstechnica.com/security/2016/05/chinese-arm-vendor-left-developer-backdoor-in-kernel-for-android-pi-devices/ Troubling read.

Hello, how to enable analog tvout? I have OpiPC board with legacy jessie desktop armbian image. I added module tv in /etc/modules. I change script.bin with: [disp_init] disp_init_enable = 1 disp_mode = 1 screen0_output_type = 3 screen0_output_mode = 10 screen1_output_type = 2 screen1_output_mode = 11 fb0_format = 0 fb0_width = 0 fb0_height = 0 fb1_format = 0 fb1_width = 0 fb1_height = 0 [tv_para] tv_used = 1 tv_dac_used = 1 tv_dac_src0 = 0 But there is no signal at all... I checked tvout with loboris ubuntu image (added "tv" to /etc/modules and fixed script.bin) and my tvout worked well. I noticed that when ubuntu image is loading tvout already gives to…

Hello, Has anybody successfully used the IR sensor on Banana Pi M2? From this, after I load the sunxi-cir module, I should see the sensor in /sys/class/rc/ but I see nothing. Nothing on dmesg either. Anyone who could point me in the right direction?

Good evening. I am preparing an Orange PI Plus 2 in order to be the first computer for my 8 years old son. The idea is that he could learn Scratch by watching some video tutorials in YouTube The problem is that actually, if you pause a video, and the you want for it to restart, only video does it. Sound doesn't starts again.It remains muted. Then, if you click to watch another video, sound come back. But you loose it again if this second video is also paused. It's a bit annoying. Do you have the same issue ? Best regard. Maesstrissimo.

Hello, First I would like to thank Igor for his amazing work on Armbian! I know that the Lamobo/BPI R1 is very problematic with power and SATA, but when I installed Armbian 5.1 jessie with the legacy kernel, it seems that the SATA is working fine. But when I tried the same Armbian 5.1 with vanilla kernel it wasn't able to boot and the hard drive made knocking noises. Just to make sure, I disconnected the HD and it booted fine. I think that this is a software problem (maybe uboot?) because as I mentioned it works with the older kernel. I tried installing the uboot package bananapro-next as Igor adviced someone with a banana pro but it didn't help. I'm using a good…

Hi! Using Jessie, I made the mistake of running apt-get upgrade => and on the next reboot by R1 did not boot anymore. I can chroot into the image (using qemu-arm-static) but have absolutely no clue what went wrong: Checking my dpkg.log, I found that the kernel seems not have been updated? root@asterix:/var/log# grep 05-10.*linux dpkg.log 2016-05-10 18:22:02 upgrade linux-libc-dev:armhf 3.16.7-ckt20-1+deb8u3 3.16.7-ckt25-2 2016-05-10 18:22:02 status half-configured linux-libc-dev:armhf 3.16.7-ckt20-1+deb8u3 2016-05-10 18:22:02 status unpacked linux-libc-dev:armhf 3.16.7-ckt20-1+deb8u3 2016-05-10 18:22:02 status half-installed linux-libc-dev:armhf 3.16.7-…

I've tried the current armbian release legacy & vanilla with my bpi m1+ board. and it looks like it's still have some distance away from an idea linux enviroment . The legacy version I've apt-get update and upgrade after login into the system, so all the software in the system is on their latest version. on default configuration, the wifi is not usable. I've to uncomment the ap6211 line in the /etc/modules file. after uncomment and restart, the wifi is usable and stable (very cool !). I've tried to transport 100G+ data through wifi interface, doesn't have any trouble with it. I can see card0 and card1 in the /proc/asound/ sub directory. and aplay -l can list 2…

Scenario 1:[router]<--(ethernet)-->[pcDuino3] pcDuino3 IP: 192.168.1.5 root@pcduino3nano:~# dpkg-reconfigure tzdata Current default time zone: 'America/Bogota' Local time is now: Wed Dec 31 20:48:49 COT 1969. Universal Time is now: Thu Jan 1 01:48:49 UTC 1970. root@pcduino3nano:~# date Wed Dec 31 20:49:01 COT 1969 root@pcduino3nano:~# ntpq -p remote refid st t when poll reach delay offset jitter ============================================================================== yak.osoal.org.n .INIT. 16 u - 64 0 0.000 0.000 0.000 bunny.zeroloop. .INIT. 16 u - 64 0 0.000 0.000 0.…

Hi! Anyone use display? GND: Shared VCC: Power supply SDA: Bus Information SCL: clock data bus From site: https://github.com/vvromanov/cb_i2c_lcd https://github.com/vvromanov/cb_i2c_lcd/blob/master/i2c_lcd.c#L28 But how to right connect display?

TKaiser. If you install the Desktop version of Armbian 5.10 then the following list of codecs (containing h.265 with 8 bit but not 10 bit!) is available for HW accelerated decoding: http://linux-sunxi.o...ed_codec_matrix Is 8 Bit versus 10 Bit a limitation. Can the Orange Pi PC with Armbian 1.10 decode all HEVC 8 or 10 bit encoding to 8 bit decoding, or can it ONLY do 8bit encoded to 8 bit decoding? Seasalt

Hi , Igor! Will you release Desktop version on base of Vanilla? Thanks.

I use your toolchain to build a Armbian_5.11_Orangepih3_Ubuntu_xenial_4.6.0.raw image, and then dd to SD card. Both OPi One and OPi PC can't boot it correctly. In the 1st time booting, the LED flashed for a while, and then re-boot automaticlly, and then in the 2nd boot and then, the serial port console only see this: U-Boot SPL 2016.05-rc1-armbian (May 09 2016 - 21:49:38) DRAM: 512 MiB Failed to set core voltage! Can't set CPU frequency Trying to boot from MMC1 U-Boot 2016.05-rc1-armbian (May 09 2016 - 21:49:38 +0800) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi PC I2C: ready DRAM: 512 MiB MMC: SUNXI SD/MMC: 0 *** Warni…

hi all, My Orange Pi PC here: uname -a Linux orangepipc 3.4.112-sun8i #30 SMP PREEMPT Sat Apr 30 19:49:10 CEST 2016 armv7l GNU/Linux and dmeg like this [ 1.017014] asoc: sndcodec <-> sunxi-codec mapping ok [ 1.017964] [DAUDIO]sunxi-daudio cannot find any using configuration for controllers, return directly! [ 1.018158] [I2S]snddaudio cannot find any using configuration for controllers, return directly! [ 1.018174] [DAUDIO0] driver not init,just return. [ 1.021480] asoc: sndhdmi <-> sunxi-hdmiaudio.0 mapping ok and I check status of ALSA lib # systemctl status alsa-state.service â— alsa-state.service - Manage Sound Card State (restor…

Hi. Can anybody give me any idea on how to find out why it is crashing? I recently moved to this distro, and it is now crashing after 1 to 4 days of continuous usage. The thing is, I have no idea how to find out why it is happening, and how to fix it. Which log should I go for? I was running this Aruntu before, and never had this issue, which seems to show that this is not an hardware issue. Best, João

Lost the login motd following apt-get upgrade. Start-Date: 2016-05-08 10:52:11 Commandline: apt-get upgrade Upgrade: linux-image-next-sunxi:armhf (5.04, 5.10), linux-headers-next-sunxi:armhf (5.04, 5.10), linux-trusty-root-next-cubietruck:armhf (5.04, 5.10), linux-dtb-next-sunxi:armhf (5.04, 5.10), linux-firmware-image-next-sunxi:armhf (5.04, 5.10) End-Date: 2016-05-08 10:56:33 I imagine I have to reinstall a pam config file?

Hi guys, Yesterday I updated my Orange PI PC with build 5.10. I want to build custom wifi driver using dkms. Dkms requires kernel scripts but scripts build fails with following error: root@orangepipc:/usr/src/linux-headers-3.4.112-sun8i# make scripts scripts/kconfig/conf --silentoldconfig Kconfig fs/Kconfig:287: can't open file "fs/fs_compat.kconfig" /usr/src/linux-headers-3.4.112-sun8i/scripts/kconfig/Makefile:33: recipe for target 'silentoldconfig' failed make[2]: *** [silentoldconfig] Error 1 /usr/src/linux-headers-3.4.112-sun8i/Makefile:493: recipe for target 'silentoldconfig' failed make[1]: *** [silentoldconfig] Error 2 make: *** No rule to make target 'includ…

root@x1c:/tmp# diff -u m1plus.dts.orig m1plus.dts --- m1plus.dts.orig 2016-05-07 17:52:38.000000000 +0200 +++ m1plus.dts 2016-05-07 18:16:36.000000000 +0200 @@ -704,6 +704,13 @@ bus-width = <0x4>; non-removable; enable-sdio-wakeup; + brcmf: bcrmf@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + interrupt-parent = <0x3a>; + interrupts = <7 15 0x00000008>; /* PH15 / EINT15 */ + interrupt-names = "host-wake"; + }; }; usb@01c13000 { @@ -1081,7 +1088,7 @@ allwinner,pins = "PI4", "PI5", "PI6", "PI7", "PI8", "PI9"; allwinner,functi…

Hello. I'm having trouble with infrared receiver. Whether the sunxi_cir driver installed in kernel or not, there is nothing in /dev/input except "event0", which is the power controller. Dmesg doesn't show anything neither. Version: Armbian 4.5 Lamobo-r1 Debian jessie next (unofficial), kernel 4.2.3. IR support was declared on download web page, so I decided to get vanilla kernel. That's because I had already tried Bananian with 3.18 kernel, and there were huge problems with kernel ppp (up to freezes of whole device). Has anybody encountered this problem?

LED link on WAN port ON when disconnect cable link ( not change to OFF, always ON). Help me how to fix the problem

Hello. First of all sorry if this isn't a place to post this. I recently bought an orange pi one. And I'm using Armbian OS. (Latest version downloaded from Armbian website) But there seems to be a problem with WiFi and i searched all over the internet and i didn't found anything about it. So here is how it was: First time that i wrote the Armbian OS on the SD card and configured it (as said by the Armbian website I didn't connected the WiFi dongle) and after doing those stuff I did connected the WiFi dongle to it. It worked fine, but after some mins both LEDs were on. And nothing was working. I did the things I said above many times and the same happend. And once I d…

Hi guys, I am very sorry to bother you, I tried everything I could to make this work but unfortunately, I can't figure it out. So here I am asking for help ! I am using the Armbian 4.5 Jessie (Kernel 3.4.109) on an Olimex Lime A10 board, everything works fine (Wifi & Bluetooth via USB dongles), but there's no sound. I tried aplay -l but nothing is found. modprobe sun4i_codec returns "codec not found". Could you help me find what's wrong ? I would like to avoid compiling a kernel by myself if it's possible ... Thanks !

Ununtu 14.04 in a VirtualBox VM Latestes Armbian ./compile.sh BOARD=orangepiplus KERNEL_ONLY=no PROGRESS_DISPLAY=plain RELEASE=wheezy KERNEL_CONFIGURE=yes KERNEL_KEEP_CONFIG=yes COMPRESS_OUTPUTIMAGE=no BUILD_DESKTOP=no ..... [ o.k. ] Installing packages for [ Armbian ] Reading package lists... Building dependency tree... Reading state information... E: Unable to locate package f3 [ error ] ERROR in function create_rootfs_cache [ debootstrap-ng.sh:245 ] [ error ] Installation of Armbian packages failed [ o.k. ] Process terminated [ error ] ERROR in function unmount_on_exit [ debootstrap-ng.sh:539 ] [ error ] debootstrap-ng was interrupted …

I noticed somebody did some work. All I did was add xenial to the compile script and it went through without any errors. Impressive. Welcome to ARMBIAN Ubuntu 16.04 4.4.5-sunxi Any reason an alpha image isn't available? Would you like the one I made?

Hello ! I'm a proud owner of a Opi One which is supposed to be my media server and torrent server. I downloaded and installed Armbian, set it up, everything works great, but the only problem is video playing. I tried to run multiple videos and multiple formats (.mkv, .mp4) but the player remains black. If I go on youtube, the video plays but it's very laggy (like 10fps). What should I do ? Thank you ! Guess here is my answer, too: http://forum.armbian.com/index.php/topic/1129-h265/

Hi, I got a "Orange Pi Plus 2" and installed armbian in it: http://www.armbian.com/orange-pi-plus/ It is necessary that the operation of the web browser becomes more fluid, do I need this in my application. I need another browser version? which one? I need to enable something to be accelerated 2D and 3D? How to? Forgive me because of my bad english.

Hello. I soldered CR2032 battery to BAT1 on Banana pro board. Setup current date and time. But RTC not working. :-( When I restart the board I see old date and time. Please tell me, how can I turn on RTC?

Hello, this is my first topic on the forum. Please forgive my English is poor. I use Orange Pi PC, version Armbian_5.05_Orangepih3_Debian_jessie_3.4.110, with a patch to kswapd0: CMA-linux-image-sun8i_5.07_armhf.deb from this: https://github.com/igorpecovnik/lib/issues/219 SD card is: SanDisk microSDXC UHS-I 64GB speed up to 48MB/s (write speed in OPi is over 20MB/s). I have a problem that when writing to the card. For example, downloading a file by multiple instances wget. The SD card stops responding and crashes Opi. Only helps to disconnect the power supply. The card is new and fully operational. When I connect the monitor displays the following messag…

So i'm using Orange Pi PC with the latest armbian desktop image. I've noticed this issues: -Booting takes a long time with wifi adapter (realtek 8188etv), stucks at "lsb raise network interfaces" for 2 minutes, than continues -Browsing shares via thunar results in this error -No chrome/midori in repos ?

Hi, first time posting, I tested the legacy image and vanilla image. --- Legacy --- Legacy is working fine, nand install is very easy to use. --- Vanilla --- Vanilla, stopped responding after the kernel is decompressed and the last message was about loading it, there is no additional info in UART or HDMI. Lucas

Updated this afternoon and noticed my SATA drive isn't connecting. > dmesg | grep SATA [ 3.633118] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 32 [ 3.952927] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.781288] ata1: SATA link down (SStatus 0 SControl 300) [ 10.102706] ata1: SATA link down (SStatus 0 SControl 300) [ 10.102730] ata1: limiting SATA link speed to 1.5 Gbps [ 15.422687] ata1: SATA link down (SStatus 0 SControl 310) Let me know what I can do. Thanks!

Hi, am new on orangePI, Hope my question is not to dumb. I am using the Armbian_5.05_Orangepih3_Debian_jessie_3.4.110.raw image. Kernel is Linux orangepipc 3.4.110-sun8i #18 SMP PREEMPT Tue Mar 8 20:03:32 CET 2016 armv7l GNU/Linux I want to access a serial device connectet to the pins 8 and 10 on the GPIO connector, described at uart 3. /dev/ttyS0 is the 3 connector pin close to the power plug. there is no /dev/ttySn with n>0 and the /dev/ttyGSn are also not the ones to use. How can I create the right device? Same about the IR receiver, Is there any device that represents the IR receiver? Are there modules to load? thanks a lot for help

Tried to build kernel only for OrangePih3 ( I have an Orange Pi One) and the build failed while trying to patch u-boot. Below is the install.log file since the forum software won't let me upload a file of type .log and once I tried, it won't let me attach anything, but that's another problem... Which turned out to be a cockpit problem ;>P +++++++++++++++++++++++++++++++++++ Displaying message: Preparing host info Displaying message: Host system support was not tested rosa wrn Config: linux-sun8i-dev Kernel source: https://github.com/wens/linux Branch: h3-emac linuxsource: linux-sun8i-mainline Offset: 1 bootsize: 0 bootloader: git://git.denx.de/u-boot.git bootso…

Hi, I've tried to finally move on from 5.04, but the new image doesn't boot. At least, HDMI doesn't show anything and my router doesn't see the board when connected via ethernet. On the first power-on the green led glows a few minutes, then red one blinks a few times alone, then both leds blink and then only green one glows. On successive boots only green led glows uninterruptedly. Do you need any information to make it work? BTW, legacy kernel worked fine for me, except my HDD connected with hdd-usb adapter (Agestar 3FBCP1) spits errors every few seconds and performance is unbearable. Connected to my router with TomatoUSB the same hdd works fine. I hoped n…

I downloaded: http://mirror.igorpecovnik.com/Armbian_5.10_Pcduino3nano_Debian_jessie_4.5.2_desktop.7z and burned it to an SD card, when I tried booting the board, all I get on the uart console is the u-boot SPL signon message +++++++++++++++++++++++++++++++ U-Boot SPL 2016.01-armbian-sun8i (May 01 2016 - 01:05:19) DRAM: 1024 MiB CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 Could not determine boot source resetting ... +++++++++++++++++++++++++++++++ This repeats forever... I had previously used: http://mirror.igorpecovnik.com/Armbian_5.00_Pcduino3nano_Debian_jessie_4.4.1.zip and it worked fine on the same board. I tried recompiling u-boot from source u…

Hi, I have a Cubietruck with ARMBIAN Ubuntu 14.04.4 LTS 3.4.110-sun7i. I now want to use the Hardware acceleration for encryption. But I'm not able to do this and i have not found a lot of Information. I should load the sun4i_ss Kernel module, but i'm not able to find this on my cubietruck. Do I have to install an additional Package or do i have to compile the module by myself? By now my encryption is working by software: $ cat /proc/crypto name : ecb(arc4) driver : ecb(arc4-generic) module : kernel priority : 0 refcnt : 1 selftest : passed type : blkcipher blocksize : 1 min keysize : 1 max keysize : 256 ivsize : 0 g…

Hello, Did not start Orange Pi PC Armbian_5.10_Orangepih3_Debian_jessie_4.6.0-rc1 graceful on the Microsd and trying to start it. It is a serial TTL and HDMI are not so thin air conditions. from RC Nice in this recognition within the range of the bug? My best regards.

Hi, Recently I've made a custom kernel for an Olimex Lime board. The NAND driver refused to load and reported "kernel divide by zero". I believe the problem is in drivers/block/sunxi-nand/nfd/nand_block.c in function get_cmu_clk. The function (with my patch line) is: __u32 get_cmu_clk(void) { __u32 reg_val; __u32 div_p, factor_n; __u32 factor_k, factor_m; __u32 clock; reg_val = *(volatile unsigned int *)(0xf1c20000 + 0x20); div_p = (reg_val >> 16) & 0x3; factor_n = (reg_val >> 8) & 0x1f; factor_k = ((reg_val >> 4) & 0x3) + 1; factor_m = ((reg_val >> 0) & 0x3) + 1; …

For /etc/update-motd.d/30-sysinfo I noticed it likes to say my system is up 6 seconds and then when I check with uptime I notice it's wrong and has been up for hours or over a day. Just curious if there is a reason for not doing it in a way similar to this? function displaytime { # we need dedicated function local X=$(/usr/bin/uptime -p) printf "Up time: " printf "\x1B[92m%s\x1B[0m\t\t" "$X" }

Hi all. i say goodby rental server , hello orange pi . by the way i run nginx as basic authentification . /etc/nginx/nginx.conf is ------------------------------- events { worker_connections 800; } http { include mime.types; default_type application/octet-stream; index index.html index.htm; keepalive_timeout 65; server_tokens off; server { listen 80; server_name localhost; #<-for test root /var/www/d1; } server { listen 80; server_name n------------a.dip.jp; root /var/www/d0; } server { listen …

hi im newbie OrangePI, how to make WiFiUSB work Bus 002 Device 002: ID 148f:7601 Ralink Technology, Corp. I try this step https://github.com/pvaret/rtl8192cu-fixesbut get error on this cmd sudo apt-get install git linux-headers-generic build-essential dkms root@orangepipc:~# git clone https://github.com/pvaret/rtl8192cu-fixes.git Cloning into 'rtl8192cu-fixes'... remote: Counting objects: 438, done. remote: Total 438 (delta 0), reused 0 (delta 0), pack-reused 438 Receiving objects: 100% (438/438), 1.80 MiB | 240.00 KiB/s, done. Resolving deltas: 100% (223/223), done. Checking connectivity... done. root@orangepipc:~# sudo dkms add ./rtl8192cu-fixes sudo: dkms: …

Hi! I try to build the image Lime2_Ubuntu_trusty_3.4.111 for Lime2 from Armbian repository. For this process I use this documentation - http://www.armbian.com/using-armbian-tools/ After success finish of compilation process, I write image on the SD and try to boot. After 10 sec of start the booting I get the black screen. Its image work fine Lime2_Ubuntu_1.6_trusty_3.4.106 Can you help me solve the problem?

on my a20 olimex micro board with armbian 5.0 (jessie) and 3.4.110-sun7i kernel hdmi shutdown after boot (i can see bootloader and logo) with armbian 4.5 image for lime2 hdmi works, but eth0 not working and after some time (i've tested only iceweasel) with xorg and lxde display freeze and i need to restart the board to fix hdmi with micro image i need to modify boot.scr or need to rebuild kernel/bootloader?? with micro image eth0 works and i can update&&upgrade, with lime2 image (on olimexino micro board) update&&upgrade give me errors and broke boot process