Allwinner sunxi

Hello, with 3.4. kernel I could use my csi-cam on my R1: #5.0 Mega Pixel Banana PI Camera Module for Android #and Linux. OV5640 chipset, CSI connector #Price: US $24.00 / piece from aliexpress sudo modprobe ov5640 sudo modprobe sun4i_csi0 #video stream #mplayer tv:// #snapshot mplayer tv:// -vo png -frames 1 Now I switched to armbian 4.7 with 4.2.6 to use new wifi-usb-drivers but I saw that those modules are not supported in the new kernel. :-( Source of drivers: https://github.com/LeMaker/linux-sunxi/tree/lemaker-3.4/drivers/media/video/sun4i_csi https://github.com/LeMaker/linux-sunxi/blob/lemaker-3.4/drivers/media/video/sun4i_csi/device/ov5640.c Did a…

I was curious to see how Mainline kernel performs on GbE test against a Legacy kernel. For the Armbian side i chose the nightly dev Armbian_5.27.170602_Orangepiwin_Ubuntu_xenial_dev_4.11.1_desktop.img (Desktop) and for the Legacy i chose my own build with all "Bells and whistles" (full Desktop, hdmi, camera, bt and wifi). I did not optimized Armbian Mainline, just installed and run stock. For the Legacy i optimized as usual. If there is some optimization to do on Mainline side, i missed. I have some observations about the board and results: * Board is without Heat-sink, * Legacy subsequent test got lower values, i suspect it runs h…

Hi, my Armbian Reports as 23.02.2 with Kernel 5.15.93. According to website there is already 23.5 with Kernel 6.x. How can I upgrade my existing installation? I tried apt update dist-upgrade and the "Update all packages and firmware" option in armbian-config. best regards thommy

We have a project based on FriendlArm's NanoPi Neo Air board. Currently the devices are running Armbian 18.04 LTS loaded from emmc. We are looking for a way to update the devices "offline" / with no user interaction. We can upload data to the devices via FTP and also can execute shell scripts. We can not easily access the on-board micro SD slot but have an external SD-Slot / USB-A Port with lots of free memory on each device. Any hints or explanations are very welcome!

I would like to grab a desktop img of armbian for my orange pi, I did download 1 that said desktop and have logged in and with password and created a account but as far as I can go is to the lunix prompt how do I get desktop install of can any only please point me to download the desktop img for my orange pi plus 1 2e. Thank you Sneaky

Hello everyone, Would like to ask for some guidance regarding how to install armbian on a t507 processor. as written here in this post allwinner 507 processor it says For this reason I have tried to burn an image for orangepi zero 2 but it doesn't boot, it just get frozen and I can't get any logs because the serial console do not prints anything all black. Does someone could maybe have some suggestion of what I could try? anything is more than welcome. Thank you in advance

Hy everyone, I am desperately trying to get armbian running on a bananapi pro. By using the raw files i had no luck. Did anyone ever try wether it works at all? For me id does not even boot... Thanks

Hello Armbian community. I have tried to start the latest image of Armbian Xenial Desktop on my cubieboard 2 and it does not work. I have exactly the same issue as this previous issue:

I have done a fresh installation of the Debian image (http://mirror.igorpecovnik.com/Armbian_4.5_Cubietruck_Debian_jessie_4.2.3.zip), but since that the linux does not report any information on power and the battery. There is no information in /sys/class/power_supply. As I am not an linux expert, any useful informationhighly welcome

Hello After trying (unsuccessfully) several linux distributions on an orange pi plus 2e, I was happy to find the jessie desktop, which accepts wireless keybord and wifi or ethernet connection with no need of further command line. The only problem: no sound. Could somebody help with that?

hi new armbian user here.. ive recently got a pcduino v3b and the old OSs for it suck, cant update anything or find what i need... ive tryed downloading a few builds of armbian for pcduino, but im having some issues, firstly hdmi doesnt boot, i mean, never get anything on screen, the only access i have is via the serial port ive just grabbed the latest build that says the board is supported, but i cannot get a network connection, ethernet is plugged an 'up" but no ip or connection, and it seems the onboard wifi cant be found either.... also receiving error messages about failing to reset the ethernet dma ... Starting kernel ... [ 28.028075] sun7…

So I am using Armbian on Linux with Orange Pi 5 and as I connect my Ethernet cable it is not able to connect as if i got to Firefox a tab will not be able to load. Any suggestions.

Hi guys, ive installed armbian 5.2 into my opione, now what should i do? Videos 1080p work slowly in kodi, i have to do something? Thanks Inviato dal mio HUAWEI SCL-L21 utilizzando Tapatalk

1. Orange pi pc cant shut down ,remains blink. 2. Cant eject usb /sda file directory not available. 3.funny with much updates still cant connect to Internet with clearing block interfaces from armbian config.

Hi. My board is Orangepi-PC Allwinner H3. I had wifi-dongle-usb problem.. so i used armbian.. I was download Image here http://www.armbian.com/orange-pi-one. I confirm wifi dongle is working! But Uart3 in not working.. I need uart3 for Bluetooth module.. I can't find ttyS3 in /dev/.. so i used source at https://github.com/igorpecovnik/lib I built two image.. -> Armbian_5.11_Orangepipc_Debian_jessie_4.6.0_desktop -> Armbian_5.11_Orangepipc_Debian_jessie_4.6.0 but both not working... I can see green led but i can't connect ssh... and cant' show console by monitor.. How can i do? Please help. Thanks.

Got this when I do an apt-get update root@nanopineo:~# apt-get update Hit http://security.debian.org jessie/updates InRelease Ign http://httpredir.debian.org jessie InRelease Hit http://httpredir.debian.org jessie-updates InRelease Hit http://httpredir.debian.org jessie-backports InRelease Hit http://security.debian.org jessie/updates/non-free armhf Packages Hit http://httpredir.debian.org jessie Release.gpg Hit http://security.debian.org jessie/updates/non-free Translation-en Hit http://security.debian.org jessie/updates/main armhf Packages Hit http://security.debian.org jessie/updates/contrib armhf Packages Hit http://httpredir.debian.org jessie Release Hit http://sec…

I need to clone a bigger (almost empty) sd card to a smaller one. I use rpi-clone on RPIs but since armbian has a single partition rpi-clone (or its forks) doesn't seem to work :-/ https://github.com/billw2/rpi-clone.git https://github.com/KoljaWindeler/pi-clone https://github.com/wbphelps/rpi-clone-wm.git Has anybody used successfully rpi-clone or other similar scripts on armbian? What is the best way for creating the smallest img files possible? With my RPIs I clone SDs to smaller ones, then I "zerofree" the created card and I backup it to an image file. I'm currently using this software on Windows which creates compressed img files so that I have no …

Hi, I just installed the Armbian_5.35_Orangepilite_Ubuntu_xenial_default_3.4.113_desktop.img on my 32GB SD card for my new OPi Lite. On start-up the screen res overlaps the monitor a the top and bottom and the screen text is thin, fuzzy and illegible in places. I can see from the Fine Tuning section of the Armbian documentation and a post by tkaiser that the h3disp utility can be used to modify the script.bin file to permanently update the start-up screen res. I have a NEC MultiSync LCD1830 that's optimal res is 1280 x 1024 at 60 Hz to 76 Hz so naturally I'm trying set this resolution. The monitor is connected to the Opi Lite via a VGA to HDMI adaptor. Si…

Hello community, I'm looking to build an internet cube (https://internetcu.be/). Basically, the project uses an A20-OLinuXino-LIME2 but I'm looking to see if a better armbian could do the job. Prerequisites are quite similar to a NAS : quality, stability, performance, minus 80$, Gibabit LAN, SATA, USB. So I have 4 models in mind: - Banana pro - Banana pi - A20-OLinuXino-LIME2 - Espressobin Which one is best suited and/or do you have other models in mind?

Hi, I have problem with my Orange Pi PC, where I installed Armbian_5.30_Orangepipc_Ubuntu_xenial_default_3.4.113. I install python-jabberbot and python-daemon to create daemon to do queries by jabber comunication protocol. When I am active on ssh I get answers from bot in seconds, but when I try get answer without, I must wait about 1-2 minutes to answer. Do you konow what may be responsible for this behavior? Best regards, Leszek Mazur

For /etc/update-motd.d/30-sysinfo I noticed it likes to say my system is up 6 seconds and then when I check with uptime I notice it's wrong and has been up for hours or over a day. Just curious if there is a reason for not doing it in a way similar to this? function displaytime { # we need dedicated function local X=$(/usr/bin/uptime -p) printf "Up time: " printf "\x1B[92m%s\x1B[0m\t\t" "$X" }

i've an orange pi one and i'm running armbian stretch (mainline) on it after issuing shutdown -h now as root, the green status indicator light goes off. but i noted that the ethernet leds remain on i leave the board powered on after shutdown but since i've already issued shutdown, i assumed that the cpu has stopped while i go on to work on my pc. some minutes later, i accidentally touch parts of the board and it is extremely hot, every part of the board i'd say it is probably well higher than 100 deg C, possibly a fire hazard do be careful about this as i think the behavior after shutdown is different from ubuntu xenial. for ubuntu x…

Hi, I moved from Jessie to Stretch. On Jessie i looked under a scope and generated SCK (Orange Pi Lite is Master) is clean. However, after i switch to Stretch, my SPI Slave doesn't work anymore and further investigation reviews that it has similar problem as previous builds that extra clock cycle is generated before data is transfered. The behaviour is exactly similar to following image posted by another forumer but for earlier builds. I am not sure whether any of you experience the same problem. Thanks my armbianEnv.txt verbosity=1 logo=disabled console=both disp_mode=1920x1080p60 overlay_prefix=sun8i-h3 rootdev=UUID=…

hi ( armbian stretch over orangepiPC ) i try to use OPI 5MP Camera OV5640 - Auto zoom with wide-angle lens for Orange Pi PC /Pi One/PC Plus/Plus2e However , video0 device doesnt appear on /dev/ folder. what can i do ? thanks

I bought an OPi Zero, the extension board, a 1/8-to-rca audio/video cable to plug into the AV jack of the extension board, and a 16 GB SDHC card. Loaded Armbian Stretch onto it, plugged in ethernet without any of the AV stuff just to start. The Pi doesn't even show up on my router settings so I cannot access it via Putty or any other SSH program. I turn it off, attach the extension board and av cable, and plug it into the TV in the hopes that I can start working on something with a USB keyboard...nothing shows up on the TV. I'm hoping that's a software issue and not an issue with the actual extension board I bought. I know for a fact it's loading Armbian because I can act…

as per title, armbian sucks. The last version is totally broken, unusable. Only one quarter of the screen is readable, the rest is black: why nobody has said that? Why nobody says that vlc and mpv crashes every 2 min making watching a movie impossible? The once half-decent armbian is ready for the bin now

Is there a plan for supporting the "NanoPi Duo2" from"friendlyarm" in the future? http://wiki.friendlyarm.com/wiki/index.php/NanoPi_Duo2

I've noticed that Armbian builds are taking a really long time to power up on Orange Pi PC and Orange Pi One. Is there some way I can see what's going on in the bootloader that's causing these long delays? Also, if I run apt-get dist-upgrade and take the latest kernel, it never boots after that point. I think something's wrong with the boot sector (or whatever it is) that is written/updated on the SDCard. The Orange Pi power LEDs don't light up until the bootloader successfully finds an OS on the SDCard. All of the builds over at orangepi.org work just fine but the Armbian ones aren't working right. I'm using a diverse collection of very high-quality SDC…

I noticed somebody did some work. All I did was add xenial to the compile script and it went through without any errors. Impressive. Welcome to ARMBIAN Ubuntu 16.04 4.4.5-sunxi Any reason an alpha image isn't available? Would you like the one I made?

Hi there, I do no need help how to sort it out. This is only report for Igor. I installed Jessie server image with legacy kernel on my Cubietruck few on April. I decided try upgrade to vanilla kernel about two weeks ago with command see below. And today I decided return back to legacy kernel with same command. (it is not important why but I have answer for it, I am enjoying testing ... ;-) ) ... but before I rebooted my experiencies say check /boot folder and I did not find important files there. I used command: wget -q -O - http://upgrade.armbian.com| bash And here is output of log: cat /boot/upgrade.log No packages will be installed, upgraded, …

Hello, I've been using an OrangePi PC with legacy distribution for a long time as a mini-server, it worked Ok except for some seemingly random freeze. I'm using it with an unsupported monitor size (1600x1200), so I had a modded version, and I never updated the system files to avoid having to recompile. I'd like to update Armbian to the mainline kernel version, but I want to keep all my settings/additions/installed programs, so I'd prefer to NOT do a complete re-install. Is there a way to do an upgrade without losing everything?? If not, how can I keep track of all the modifications currently installed so I can re-install them? TIA

Hi, I have recently upgraded Armbian as suggested with: apt-get update apt-get upgrade apt-get install -f apt-get upgrade apt-get autoremove -y After that i2c-0 stopped working: Output if i2cdetect -y 0 before upgrade: 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 70: -- -- -- -- --…

I was able to upgrade Armbian to 18.04 bionic beaver on my Banana Pi M1, and it's working (almost) fine! I used the command to update the sources.list to bionic: apt update && apt dist-upgrade -y && apt autoremove -y && apt autoclean apt install update-manager-core do-release-upgrade -d Fetched 403 MB in 8min 43s (769 kB/s) I gave "yes to all" to almost everything, except on replacing config files like KEYMAP, sshd and bind All these services I use are working correctly: network, SSH, bind, mail, cups, minidlna, SATA, USB printer, Samba This is not working: qbittorrent-nox 4.0.4 (misses libboost-s…

Update: checking download file, it seems that I downloaded Armbian_4.5_Cubieboard2_Debian_jessie_4.2.3.zip so it's not 4.81 no matter what the download pages said. I'm trying to install upstream kernel on Cubieboard 2 and kernel never starts. Attached is output from boot (I'm getting same on serial port). I did try different sdcard (to rule out problems with it) but I'm worried about ext4fs_devread read error and partition error. Is there something more that I can try? Legacy kernel works well, but I wasn't able to just upgrade kernel and u-boot on it, but that resulted in unbootable system -- which packages I have to install to migrate from legacy to upst…

Hi All, Armbian boots fine from SDcard but when I run nand-sata-install the script complains that it has no target. A #ls /dev/mmcblk* shows /dev/mmcblk0 and /dev/mmcblk0P1 When mounted, just to see, the mmcblk0P1 partition contains the usual linux directories, so I suppose this partition is definitely the SDcard No EMMC device is present. Could this be due to me performing, yesterday a: dd if=/mnt/ArchLinux_Minimal.img of=/dev/mmcblk1 bs=4M ? I did this because I read somewhere that booting up from SDCARD followed by a dd worked in some cases. Note I originally wanted to run Arch, but since there is apparently no support at orangepi.org, after…

Hi, Just received a OPiPCplus and first things first ..loading it with Armbian. Is there a guide on how to flash Armbian image to OPiPCplus internal eMMC? Searched the forum but couldnt pinpoint anything.. Christos

Hi, I'd like to keep the features provided in AX but have my OPi Lite starting and running some software that communicates with a webserver periodically over the internet without the monitor, keyboard and mouse connected unless performing maintenance where remote access isn't appropriate. Is this possible or am I looking at an Armbian Bionic (unsupported) installation?

Hi, I have an Orange PI Lite on to which I'd like to install the latest Armbian release. I had Armbian Xenial installed on the Pi Lite quite some time ago for test purposes and put it to one side while I got hardware for my Pi Lite set up for its intended use. I wiped the SD card and I was ready to download, install and set up the latest Armbian Xenial on my Orange Pi Lite when I notice the sub-heading "desktop legacy kernel 3.4.y". I'm not sure if this description appeared previously but my question is does this mean that this version, i.e. "Armbian Xenial desktop legacy kernel 3.4.y", although currently supported is no longer being updated and will theref…

Hi, I am trying to boot image Armbian_20.02.1_Nanopi-r1_buster_current_5.4.20.img, without success ... First, i am using following line to create SD ... ansible@solo:/mnt/backup$ sudo dd if=./Armbian_20.02.1_Nanopi-r1_buster_current_5.4.20.img of=/dev/mmcblk0 bs=1M status=progress ;sudo sync After connected my tty on internal pins on PCB, it is possible to connect to this tty and look at the first u-boot log ... Welcome to minicom 2.7.1 OPTIONS: I18n Compiled on May 6 2018, 08:02:47. Port /dev/tty-target-srv-nanopir1-170-position-1.2.4.1, 20:34:41 Press CTRL-A Z for help on special keys U-Boot SPL 2019.10-armbian (Feb 17 2020 - 06:18:08 +0100) …

kernel version Linux bananapim2plus 5.15.93-sunxi #23.02.2 SMP Fri Feb 17 23:49:46 UTC 2023 armv7l GNU/Linux dmesg [ 1065.023248] udc-core: couldn't find an available UDC or it's busy [ 1065.023290] misc raw-gadget: fail, usb_gadget_probe_driver returned -16 [ 1193.665509] udc-core: couldn't find an available UDC or it's busy [ 1193.665534] misc raw-gadget: fail, usb_gadget_probe_driver returned -16 [ 2883.115015] udc-core: couldn't find an available UDC or it's busy [ 2883.115040] misc raw-gadget: fail, usb_gadget_probe_driver returned -16 [ 2908.077549] udc-core: couldn't find an available UDC or it's busy [ 2908.077574] misc raw-gadg…

Hello I'm investigating update from wheezy to trusty on my OrangePI (A20) based home media server. I'm using custom kernel 3.4.110 with SATA multiplier support. System is on HDD. I had few remarks and issues (part of them were solved but some are not): - Video acceleration was not working out of the box on trusty desktop image but it was solved it by installing "Desktop-extras for Jessie-desktop (sunxi)" - it looks it could be added as default for trusty. But mvp package can't be installed due to depedencies to libs which I did not found in ubuntu reps?! - compositing if OFF in xfce but when I moving windows on the desktop, CPU load is becoming 100% till I stop movi…

Armbian_5.20_Bananapipro_Debian_jessie_4.7.3 Armbian_5.20_Bananapipro_Debian_jessie_4.7.3_desktop both images are not working on my bananapro. Actually when I tried the first time they worked properly but after that time when i tested other images from lemaker links. After from that time no armbian images are working. keyboard and mouse are not able to power up. Also it showing swap on /var/swap. Priority:-1 extents 1 across 131068k SSFS and keep waiting there only. Please help me i was successfully able to build can4linux on armbian Debian desktop 4.7 which is not at all possible on other images.

Hi everybody, just downloaded Armbian_5.30_Orangepizero_Ubuntu_xenial_default_3.4.113 and flashed. I can see "orangepizero" in network, also ip is pingable but ssh port is closed. Is it a known issue? Armbian_5.30_Orangepizero_Debian_jessie_default_3.4.113 from archive works fine. Thanks

Hi folks, I'am setting up an Orange Pi Zero with Armbian_5.38_Orangepizero_Debian_stretch_next_4.14.14.img. After "sudo apt-get install dnsmasq" the system responds: Err:1 http://httpredir.debian.org/debian stretch/main armhf dnsmasq-base armhf 2.76-5+deb9u1 Could not resolve 'httpredir.debian.org' Ign:2 http://httpredir.debian.org/debian stretch/main armhf dnsmasq all 2.76-5+deb9u1 Err:1 http://security.debian.org stretch/updates/main armhf dnsmasq-base armhf 2.76-5+deb9u1 Could not resolve 'httpredir.debian.org' Err:2 http://security.debian.org stretch/updates/main armhf dnsmasq all 2.76-5+deb9u1 Could not resolve 'httpredir.debian.org'…

Hi, I have a Cubietruck and install Armbian_5.38_Cubietruck_Debian_stretch_next_4.14.14.img from https://www.armbian.com/cubietruck/. Copied with Etcher the unpacked .img-File to a SanDisk Ultra 32GB micro SD HC1. But no system comes up Last message U-Boot 2017,14-armbian (Jan 24 2018 ... . . Loading Device Tree to 49ab5000, end 49b29fff ... OK Starting Kernel No blinking cursour on top of the left side. Nothing go's on! System with Armbian_5.37_Cubieboard2_Debian_stretch_next_4.14.14.img works, but no network with armbian-config, neither static nor DHCP, can configure. (dnsmasq.service not found) LAN-Cable ist pluged. …

Hi, I just downloaded this image from here (this is the link i copied from the bananapipro site): https://dl.armbian.com/bananapipro/Debian_stretch_next.7z and i got Armbian_5.38_Bananapipro_Debian_stretch_next_4.14.14.7z on my disk. Unpacked it and put it on my sdcard with etcher. Tried to mount it as loop device --> error. Checked with gparted --> it said /dev/sdc1 is not ok. Repaired it with gparted and could mount it. Put it with etcher on the card. --> Bananpipro does not boot. Red light is the only one that shows up, none of the other led is blinking. What can i do? best regards Ralf

Hi - Just checked out latest greatest code from git to compile new stretch image for my NanoPiNeo2 ( Armbian_5.46_Nanopineo2_Debian_stretch_next_4.14.47 ) but seems it won't boot up. Tried two SDcards and two different boards but same result. Tried both Etscher ( 1.4.4 ) and Rufus ( 3 ) but same result, any issue known that I missed ? Please note I am building a standard image ( thus no customised settings ) also came to my attention the board becomes quite warm, this is unusual . Thanks

trying to get ili9340 to work on orangepi pc2 on bionic 4.14.91 ... there's a fb_ili9340 module in the staging directory, modprobe passes and the only thing in dmesg is warning it's staging nothing else but when I check /dev/fb* there's only /dev/fb0 (the original hdmi output on my monitor), there's no /dev/fb1 anyone can land a hand? give a hint?

Hi, Recently I have installed "Armbian_5.75_Orangepizero_Debian_stretch_next_4.19.20" on my OrangePi Zero . I configured both Ethernet and wifi connection but I had a problem with the wifi, my board does have an IP address but I can not connect through ssh nor pinging that IP. The connection is Ok and I can get access to internet but I can not ping from any other devices on the network (error Destination host unreachable), But I noticed that if I ping (from the orangepi board ) the host machine then I will be able to connect through ssh to that IP. I dont know if its a problem with arp last thing that I tried was to disable the network manager but I still have the…

the new version of Armbian (5.83) Does not boot from sd card I tried to install 5.69 it's work normally. I tried to all the sd card formatter rufus and wın32 disk imager and different sd cards but no way new version does not work anyway. when i burn to 5.69 it boot normally. I guess you have to control the package whıch you upladed for opi pc+ thanks

Armbian_community_25.5.0-trunk.334_Orangepizero3_noble_current_6.6.75_gnome_desktop.img I downloaded above image with assumption that it would open desktop on first powerup. However, it kept on opening command prompt on first power up. I also tried installating gnome desktop from armbian config and rebooting. Still it did not open desktop. Please guide. Thanks in advance.

Armbian_community_25.5.0-trunk.444_Radxa-cubie-a5e_bookworm_dev_6.14.0-rc1_minimal.img use to flash android phone echerdroid apk use for flash but not flashing proper not boot

I've installed Armbian_5.14_Cubieboard_Debian_jessie_3.4.112_desktop.7z and It initially worked. I tested video files playback (I think it was mpv player) and it worked smoothly, no video lag. After 4 or 5 boot-ups, I'm no longer able to start armbian. I just see u-boot starting and then (when the kernel is going to be loaded (message: "Starting kernel ...")) I see mess on screen and cubieboard is powered off (red power light goes down, also networking leds). I use HDMI output (unfortunately I do not have serial cable to try debug it maybe further). What I tried so far, without success: -changing SD card for another one (8GB cat4 for 8GB cat10) -replacing power supply …

RTL8211D PHY on OrangePi Prime is not detected neigther in uBoot mode or Kernel mode. Will share the logs ASAP. Please suggest!

OrangePi PC Armbian 5.35 with LXDE desktop Firefox 57.0.1 I haven't done anything with my OPi for 6 months, so when I tried it again, it booted normally except for not looking quite right on my big HDMI screen. I remember fiddling with this in the old immediate-post-boot phase, but http://armbian.com says to use "sudo armbian-config". There were 250 MB of updates, which took forever. Meanwhile I tried to run Firefox, which repeatedly crashed on startup. Installing v61.0.1 didn't help. Also Konqueror, but not Dillo or Midori or Chromium-browser. Back to fixing the display, I tried running it but didn't have the armbian-config, so I downlo…

I downloaded Armbian_5.59_Orangepizero_Ubuntu_xenial_default_3.4.113.img, and am running it with a 16GB SD card. I am trying to modify the I2C settings, however, when I type `armbian-config`, and select `System`, there is no "Hardware" menu option. This contradicts the documentation: Hardware is supposed to be an option in that menu. This is the current content of the /boot/armbianEnv.txt: verbosity=1 console=both overlay_prefix=sun8i-h3 overlays=usbhost2 usbhost3 rootdev=UUID=54dfde69-e472-48dd-a099-636a963154f3 rootfstype=ext4 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u

Hi I am trying to set up auto-login with enable desktop, using armbian-config as user root, and getting 'killed' once I select which under-priviledged user to enable. (There's two to choose from, and both behave the same with the same error reult). I couldn't find a known issue, please help! OPi Zero LTS 512MB / Armbian from armbian.com Sam

Im in the progress of making an internet radio with an Orange Pi Zero plus using armbian. Ive just gone to enable the audio device in armbian-config and when i go though to system -> hardware, the list is completely blank with just tick boxes but no content Any ideas? thanks

hi, how to use "armbian-config" set "orange pi zero" to wireless wi-fi AP for Armbian_5.38_Orangepizero_Debian_stretch_next_4.14.14. Because , i got dnsmasg service failuer........................ other question: default interface should i chose(wlan or eth)

When trying to upgrade, I get the following error: root@orangepilite2:~# apt upgrade Reading package lists... Done Building dependency tree Reading state information... Done Calculating upgrade... Done The following packages will be upgraded: armbian-firmware 1 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 0 B/5,755 kB of archives. After this operation, 0 B of additional disk space will be used. Do you want to continue? [Y/n] (Reading database ... 38292 files and directories currently installed.) Preparing to unpack .../armbian-firmware_5.74.190202_all.deb ... Unpacking armbian-firmware (5.74.190202) over (5.72.190122) ... dpk…

Hi I have old orange pi A20 board with vga https://www.armbian.com/orangepi/ It armbian loads as expected, environmet file I added the fdt line. But after I reboot after command armbian-install after transfering files to the ssd hard drive it board does not start without errors. failed to mount media/mmcboot dependency failed for /boot dependency failed for local file systems <..> you are in emergency mode attached image of the error: imgbb_link

After running the armbian-install program and selecting option "1 'Boot from SD - system on SATA, USB or NVMe'" the program transfers the contents of the SD card to the drive (SATA or NVMe). And it works. The problem occurs after booting - a message appears about the device being unable to mount /media/mmcboot . And indeed - the contents of /media/mmcboot and /boot are empty. The problem turns out to be the contents of the /etc/fstab file generated on the SATA/NVMe drive. The mount point /media/mmcboot has a only UUID value, but the text "UUID=" is missing before the value. After manually adding it, everything starts fine. If someone could lean in and correct th…

i wanted to use my Banana Pi M1 for displaying multimedia content from websites like twitch.tv but firefox-esr and chromium crash when I try to load them. firefox opens its crash report box without a possibility to look at the related error messages. But the output of chromium can be viewed here: http://dpaste.com/37M0QNC It was installed from Armbian_5.65_Bananapi_Debian_stretch_next_4.14.78.img plus dist-upgrades. Iinitius

Hi, ALL! Have anybody success story with an Armbian and Kodi? With Armbains 5.05...5.10 I installed (apt-get update ; apt-get install kodi) kodi 15.2 from this repository: Quote as described here and allways (in all Armbian releases) has a problems with a sound: sound level very low ans high level noise starting even no video - beginning while kodi GUI started (permanent noise in menus). Film sound also exists while film started playing, but sound level near noise level and very low both (btw, kodi volume regulator not working, only mute mode working in kodi). I watched AC3, MP3, AAC sound coded films - effects are the same: noise with low volume soundtrack. A…

Armbian_5.14_Orangepipc_Debian_jessie_3.4.112_desktop after upgrade sys not restart automatically

Hi I am trying to compile a program test for my new OPi Zero that is running ARMBIAN. From a Hello World program test, I am trying to create a thread that will blink the led at PA17 gpio pin, but GCC's linker complains saying that can't locate pthread_create() function. I am using pthread.h. Somebody found similar issue? Sergio

I have to clear possible blocked interfaces everytime I log on to get access to Internet. I m connected to network but if i dont clear that button i dont get access. Can help me .

Hi: Trusty ubuntu is workig great on my CT. It boots into /root and uses this as Home. I set up a new user in /home/armbian and now I would like to boot into this user. I installed lightdm but the system still boots into /root and does not show a log in screen after boot. How can I fix that? Thanx in advance BTW: $ aplay speker-test works after boot. When I run youtube in root video is working fine. Sound comes up only for a fraction of a second and then mutes. After that aplay is also not working any more. Any clou?

Hi ,,I'm a new user,,,,,OP Zero , I have this mess in the armbianEnv.txt , but i didn't edit it ssh-ed25519 AAAAC3NzaC1lZDI1NTE5AAAAIDb34fWZZQ2gTi9CuFLQbQ0S3dRH48ZKkzjv6xZ6lFs$ ^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^$ usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u Is correct? How is the default file? Can someone gime the correct? Thanks

Of the 10 columns of output, only 4 seem to be working. Time, CPU Frequency, Load & Temperature. The other 6 columns seem wrong. I'm running Armbian_5.25_Orangepizero_Debian_jessie_default_3.4.113.img Running minerd --benchmark on the console and armbianmonitor -m in a ssh session produces this :- Time CPU load %cpu %sys %usr %nice %io %irq CPU 06:25:10: 240MHz 0.13 1% 0% 0% 0% 0% 0% 47°C 06:25:16: 1200MHz 0.36 1% 0% 0% 0% 0% 0% 64°C 06:25:21: 912MHz 0.65 1% 0% 0% 0% 0% 0% 68°C 06:25:26: 912MHz 0.92 1% 0% 0% 0% 0% 0% 65°C 06:25:31: 912MHz 1.17 1% 0%…

Hi, I have some armbian 5.38 (kernel 4.11.5) installations and recently updated them. With this update I got kernel 4.14.18. When I executed command "armbianmonitor -m" I used to get something like this: :~# armbianmonitor -m Stop monitoring using [ctrl]-[c] Time CPU load %cpu %sys %usr %nice %io %irq CPU PMIC 10:52:13: 528MHz 0.35 21% 2% 18% 0% 0% 0% 40.8°C 41.0°C 10:52:18: 528MHz 0.52 21% 2% 18% 0% 0% 0% 40.7°C 41.0°C 10:52:24: 528MHz 0.47 21% 2% 18% 0% 0% 0% 40.7°C 41.0°C Now after update, and kernel 4.14.18 among other new packets, I got this: …

I was installing real time clock on Orange Pi One board ... , after some unsuccessful tries I found that the battery has bad solder and all is fine now date was set "up" and "down" ... from Sat Jan 1 02:06:23 EET 2000 to Thu Jul 8 21:37:42 EEST 2032 several times ... and during all this time armbianmonitor was running (I did not check it every time ... I made many reboots ) now armbianmonitor shows some "static" data , in which the time is always 0:18.50 ... and I am thinking that may be it is showing the "last" recorded , I mean the higher date/time ...which is somewhere in the future 2032... I try reinstalling armbianmonitor ... did not helped how to remove …

I used armbianmonitor -r on my OPi Zero just like I did previously on OPi One. On OPi One everything is working fine. On my zero it doesn't display all the information for CPU. It shows: CPU total: undefined% (Sys: undefined%, User: undefined%, I/O wait: undefined%, Nice: undefined%) CPU frequency: 1.008GHz DRAM frequency: Not available Governor: ondemand Active CPU cores: 4 Vcore: undefined If I run armbianmonitor -m it shows these data I checked Allwinner_H3_Extended.conf and I noticed that it reads files from /tmp (/tmp/cpustat, /tmp/disktemp, e.t.c) On my OPi One I see these files On OPi Zero there is no rpim…

Hi All, Can you please help me how can I set up OV5647 camera with Orange Pi One? Where can I find driver for it? Camera link: https://www.aliexpress.com/item/Orange-Pi-fish-eye-Camera-Night-Vision-for-Orange-Pi-PC-Zero-One-PC-Plus-Plus2/32864676943.html?spm=2114.search0604.3.26.74868de282hQoP&ws_ab_test=searchweb0_0,searchweb201602_5_10065_10068_5015215_10059_10696_100031_10084_5015115_10083_10103_451_10618_452_5015815_10304_10307_10820_10821_5015915_10302,searchweb201603_16,ppcSwitch_5&algo_expid=44e91c9c-67e1-49b9-83f3-2c2890deab01-3&algo_pvid=44e91c9c-67e1-49b9-83f3-2c2890deab01&priceBeautifyAB=0 Thanks!

I find orangepipc packages in http://apt.armbian.com/dists/stretch/main/binary-armhf/Packages they are: linux-stretch-root-dev-orangepipc v5.37 linux-stretch-root-next-orangepipc v5.37 linux-headers-sun8i for kernel-3.4.113 v5.35 linux-image-sun8i for kernel-3.4.113 v5.35 linux-u-boot-orangepipc-default v5.35 same as they in Jessie.. what's the status about debian stretch on orangepipc? gfx, network, video?

Hi to all, I have been using banana pi pro and m1 for some years as mini PBX with asterisk, due the stop of bananian's development that works perfectly but now is obsolete and vulnerable, i'm testing armbian but registered prompt audio sounds choppy and i can't find reasons, I tried to move files in ram disk, use usb to lan interface, increase process priority, use performance ad cpu governor, also tried Armbian 5.83 Bananapi Debian stretch next, same problem. Any suggestion ? Thanks advance.

Hi I'm going use the terminal armbian and send AT commands to the gsm SIM800L, but I am uable to write these commands. I used screen and minicom like this : screen /dev/ttyS0 115200 & minicom -b 115200 -o -D /dev/ttyAMA0 I use to connect to ttyS3 but nothing happen i think the uart3 or pins 8 and 10 is not working or not enable of course i have ttyS3 in ls /dev list but not working. I've connected according to the following guidelines: i use : orange pi plus 2 board armbian for orange pi plus 2 SIM800L v2.0 image of my connection and board :

I am try to activate the audio for cubieboard 2 with the OS armbian with the kernel 4.1.4 and I do not get it by the output jack. Before I install this distribution, I had a cubieez and this OS worked the audio with alsa. Is impossible have audio with this kernel? Thanks in advance!

Hello I install alsa-utils and mpc , mpd but have hum from the speakers. And when try use alsamixer get sudo alsamixer cannot open mixer: Invalid argument I use jack-audio not hdmi

Hello, I try to enable audio linein, controls with alsamixer are the following. Is it possible to redirect audio input to output directly or with audio equalizer ? I actually have sound with a speaker test, but I can't listen to the audio line-inActually I have sound with speaker test, but I can't listen audio linein Best regards

Hi, Trying to setup audio mux on orange pi boards, for now trying to stick on orange pi ZERO & ONE ( both of them ). By mux, meaning will try to setup some peers which can play locally or stream sources they have. Let's say all peers have - x2 line in - x1 mic - x1 line out Want to dynamically connect any source to any output on any peer. For example after choosing, you can able to play line in of peer 1 on peer 1 output OR peer1 line in on peer 2 output And I think CD quality is more than enough. Trying to find any tools that will help to make this. Two solution points needed: - hardware: ?? as far as I can find, there is "line…

Hello! I found that on NanoPi K1 Plus there is issues with both of integrated audio adapter (H3 Audio Codec) and HDMI Audio (allwinner-hdmi 1c22800.i2s-i2s-hifi) 1. With H3 Audio Codec I getting only silence, altrought there is short click on starting and end of playback. "Stereo" mode was chosen in pavucontrol for this audio adapter. 2. With allwinner-hdmi audio playback is working, but left and right channels is swapped. Like above "Stereo" mode was chosen in pavucontrol for this audio adapter. Tests was performed from Mate desktop installed on top of Armbian 20.05.4 with Linux 5.4.45-sunxi64. "speaker-test -t wav -c 2" command was used for te…

We are in the process of migrating from NanoPI NEO's to NanoPI NEO Core's as part of that we are moving to mainline NEO Air / NEO Core images. I noticed that audio playback is soft / fades in at the start of the file. This only seems to occur on mainline images. Thoughts?

Hello, I am on a nano pi neo, I get an optical input with an external usb audio card. I d'ont know how to use the onboard spdif as an optical input so is it possible to get the optical input of an usb card (wich I see with alsamixer) an output sound to the local analog output (I already can play sound on this output) ? Maybe a loopback or an audio software could helps.... Best Regards

History work: started my work from raspberry pi but recently shifted to orange pi. On raspberry, me used teh UV4I server wif webrtc to broadcast video streaming and send controls through data channels from a web browser to control a robot. My application: So basically my application is a semi-autonomous car wif two cameras.me want to control teh car from a web browser and stream a video of both cameras on teh browser Issues: 1: On orange, pl broadcast streaming from USB cameras to a web browser? 2: Send controls from web browser to orange pi? 3: Teh UL4l drivers are not installable on an orange pi pc so need to find an alternate 4: halp to fi…

Machine model: Banana Pi M2 Berry Linux bpi08 6.2.7-sunxi #3 SMP Fri Mar 17 07:58:04 UTC 2023 armv7l GNU/Linux (armbian@next) Mir ist es nicht möglich eine interne Temperatur auszulesen. Brauche dringend Hilfe! Der Link“/etc/armbianmonitor/datasources/soctemp “ exitiert zwar, nur die Datei / das Verzeichnis existiert nicht: nicht vorhanden → /sys/devices/virtual/thermal/thermal_zone0/temp nicht vorhanden → /sys/class/thermal/thermal_zone1/temp Wo soll diese Dateien überhaupt erstellt werden? Anmerkung Es wäre schön, wenn es für den Banana Pi M2 Berry eigene Tags geben würde. Er unterscheidet sich von dem Banana Pi M2+.

Hi, I used dd command to prepare the SD with download of Cubietruck_Debian_3.8_jessie_3.4.107. It asks to change password immediately, I typed a new password, it gives me Authentication token manipulation error. No way to login. Please help.

I obtain an "Authentication token manipulation error" on Banana Pro Debian 3.0 jessie 4.0.4 when I try to change the rot password in the first run. Any help? Thanks

Hi, I am running armbian 4.11.6-sunxi with xfce4 on a Banana Pi M1. I need to login automatically without having to choose a session before login to the xserver. I am achieving the autologin OK but can't get rid of the session request . How can I achieve autologin complete with new session? Thanks for helping if you have an answer.

@dear Igior and others My R1 fw1 run fine past 2 month with the 3.19.3. now its time to move to 4.0.x Igor - many thanks for KERNEL_CONFIGURE at your scripting implementing . This shortcut my work with automated rebuild kernel an bit -- but not fully. I have the need to been able to push my own kernel .config into your https://github.com/igorpecovnik/lib in an automated way. But how about to push an custom .config into that? welll ... My suggestion are here top add i.e at your compile.sh : KERNEL_CUSTOM_CONFIG="/path/file" if file env set , use it instead from default patched kernel .config How you think about this Idea ?

Just made my first GPIO script in python for the Orange Pi One but now am looking for some assistance in getting Armbian to login automatically on boot and run the script as sudo. Any help would be greatly appreciated.

Hi, I'm using ARMBIAN Ubuntu 14.04.4 LTS 4.4.3-sunxi on a Cubietruck board with a battery connected. How do I setup the system to safely suspend, shutdown or hibernate when the battery power is low? Thank you very much.

I was wondering if I could have automount feature for every UFD or USB Hard Drives to the /media folder. As i've investigated it, it would only mount if I get to click its icon on the desktop. I'm running bananapi as my headless file/media/print server. I shared the /media folder to the network through samba and was kept wondering why I'm unable to access every flash and hard drive I'm connecting to my bananapi as it does in my Raspberry Pi (when I share its /media folder in samba). Is there anything that I could do instead of adding it to fstab and manually restarting or manually mounting it every time I connect a media to my Banana Pi server? …

Hi, I have written a program with python e tkinter. The Gui automatically starts and runs well only I do access through remote desktop. How can I do that orangepi pc simulates the connection and starts my Gui? Sorry for my english, I hope I was clear enough. tx Ema

Hi I'm auto-login using nodm with orange pi. I run my udp.py file by creating a file named udp.desktop under the .etc/xdg/autostart folder at startup. but I need to play the wav file using pygame in the .py file, but I get a warning that the audio device could not be initialized. If I trigger my .py file manually, I can play the wav file without any problems. probably unable to load sound drivers during autostart. Can you help with this.

Banana Pi (original "model 1") A20 Was running flawlessly on Xenial - latest updates - almost everything worked (I run it on a LiPo battery to transport back and forth from work to keep my Resilio Sync data "in sync") Resilio seems to work fine - except in Bionic I can't use avahi to resolve names on my LAN... this worked in Xenial on the same hardware. The reason I decided to try out Bionic? Couldn't find a resource to upgrade from OpenSSH 7.2 to 7.3 or greater (I'm making heavy use of features not available in OpenSSH 7.2 on my other machines). I've tried tweaking my /etc/nsswitch.conf file to no avail... Sheesh - "avahi" just worked out of th…

Hi, I have a problem with an update notification that seems to be permanent. The following lines always appear when I log onto my system: Welcome to ARMBIAN 5.36 user-built Debian GNU/Linux 8 (jessie) 4.13.16-sunxi System load: 0.71 0.63 0.62 Up time: 1 day Local users: 2 Memory usage: 29 % of 995MB IP: 192.168.2.103 CPU temp: 42°C Usage of /: 60% of 15G [ 0 security updates available, 2 updates total: apt upgrade ] Last check: 2017-11-26 00:0012 After sudo apt-get update and upgrade the lines telling me that 2 updates are available are still …

Hi to everyone, I'm new at armbian forum, but following the project since some month. As far as I can tell all contributors make a great job to enable a stable debian based distribution to many as possible arm-based boards. Thanks a lot for this great job. I bought one of the first available Banana Pi M3-boards in Germany, because I wanted (and did it already very successfully) to set up a small server for email, music storage, mythtv-backend, read out my central heating.... Until now I use a stripped down image based on the provided Ubuntu 16.04 image from http://www.banana-pi.org/m3-download.html As you all know the "support" and further developmen…

AFAIK, from last year, there are some new driver for AXP209/202 PMU for mainline kernel. One of the main new features that i really like is custom sampling frequency compared to the original driver for linux kernel 3.4 (i just remember the interval are 2 seconds). I want to use AXP209 PMU for power/energy profiling and consumption study of some SBC such as Banana Pi/Pro and some other Allwinner based SBC as comparison. The question is How i want to know current sampling frequency from PMU and how to change the frequency? (25, 50, 100 or 200Hz) What is the reasonable/best practice to write the captured power consumption value (with timestamp) into some logf…

Hi all, I have applied 12 V to the DC input of my Cubietruck (bad thing). So now I want to repair / recover everything possible... Both DC-in and battery input seem to be short-circuited, but I cannot find the exact position. Power via USB-OTG works (successful boot). The fuse directly after the input has almost zero resistance (which is good) and I have checked all visible power-related parts (doc here) with a microscope (nothing looks burned, as far as I can tell all diodes/resistors/... work as they should). When checking the resistance of DC-in to ground it gives me 1,5 kOhm with a multimeter (don't have a second one here, but I gues…