Other families

In the nanopcT3+ board I need to enable the I2S1 (14 pin header) in Desktop version. I need to have the I2S1 peripheal as SLAVE and a MCLK of 48kHz and 192kHz (better if other clock speed are supported). The "aplay -l" and "arecord -l" commands must show the I2S1 as a sound card with input ad output device. I've tried to do the job but I'm a newbbie on linux and embedded linux. Following the official FriendlyArm wiki, on a host PC I've downloaded the kernel source, modified the dtsi file to enable i2s, recompiled the kernel and U-boot and all steps seem work fine. Now I don't know how to do a final steps to have a SD bootable image with eflasher to load and test…

hi... i have some trouble compiling a new image with the latest kernel (4.2) for udoo quad. i get an error during make drivers/pci/access.c:493:16: error: redefinition of 'pci_vpd_f0_write' static ssize_t pci_vpd_f0_write(struct pci_dev *dev, loff_t pos, size_t count, Any idea? solutions?

Hi, i am trying start Kodi on CuBox i4Pro but without success for now. - I installed armbian debian jessie on SD. - booted & rebooted - add into sources.list deb http://httpredir.debian.org/debian/jessie-backports main contrib non-free deb-src http://httpredir.debian.org/debian/jessie-backports main contrib non-free - apt-get update - apt-get upgrade - reboot - apt-get install kodi and laund kodi and crash with error ERROR: Unable to create GUI. Exiting Segmentation fault Crash report available at /root/kodi_crashlog-20151229_181607.log What now? Thanks for any hint.

Anyone get ArduinoIDE working on armbian for the Udoo quad? When I try to upload a sketch, i see a java exception for bossac - no such file or directory (when i try to run bossac -h, same error) Edit - the error above was for Udoo's 1.5.8 version. I tried 1.5.4, and now I get errors trying to create GPIO0 and GPIO117 (direction & value).

hi, i have following problem: ● brcm4330-patch.service - LSB: Patch firmware for brcm4330 Bluetooth adapter Loaded: loaded (/etc/init.d/brcm4330-patch; bad; vendor preset: enabled) Active: failed (Result: exit-code) since Wed 2018-04-11 09:25:00 UTC; 19min ago Docs: man:systemd-sysv-generator(8) Process: 454 ExecStart=/etc/init.d/brcm4330-patch start (code=exited, status=1/FAILURE) Apr 11 09:24:54 wokati systemd[1]: Starting LSB: Patch firmware for brcm4330 Bluetooth adapter... Apr 11 09:24:55 wokati brcm4330-patch[454]: * Start pushing BRCM4330 bluetooth firmware to device and waiting 5 sec to complete... Apr 11 09:25:00 wo…

Hello, first of all thank you for the development of the Armbian software. I am currently using version Armbian_22.08.2_Uefi-x86_bullseye_current_5.15.69 on my Terramaster F5-221. Unfortunately I have two small problems. Firstly, there is no linux header for the kernel used for compiling. Secondly, unfortunately I can't add a network interface in openmediavault. That always gives me an error. It works on Debian with Openmediavault. unfortunately this surprises me. Failed to execute command 'export PATH=/bin:/sbin:/usr/bin:/usr/sbin:/usr/local/bin:/usr/local/sbin; export LANG=C.UTF-8; export LANGUAGE=; omv-salt deploy run --no-color systemd-networkd 2…

Until yesterday my humminboard 1 i2ex worked without any flaws. Now after a restart I cannot access it via ssh anymore. I thought the Ip adress my have changed somehow cause I also restarted my router but it under active clients in router webif either. Also no video output via hdmi...guess that's normal since it's a debian server image. What I can see is the uboot showing up the count down, just quick, I could read ..wrong image format..and something with source.. that's it. Then screen turns black. I have the rootfs on msata ssd and if I remember correctly I removed all other unnecessary files from micro sd card many month ago. I…

I have a Cubox that has been running Debian Wheezy for a while and I want to do a clean install of Jessie on it. I downloaded Armbian_5.00_Cubox-i_Debian_jessie_4.4.1 and wrote it to SD card, but it won't boot. The error is: Unknown command 'bootz' I rather suspect that my Cubox is not a Cubox-i - possibly an earlier version that does not support compressed kernels. Is there some way I can work around this? Maybe re-flash the bootloader, or uncompress the kernel on another system perhaps? Thanks Andrew

Using Armbian_4.4_Udoo_Debian_jessie_3.14.28 - Wicd doesn't detect any networks (/etc/network/interfaces has wlan0 commented out). If i setup /etc/network/interfaces and edit /etc/hostapd.conf and /etc/init.d/hostapd, I can get the udoo to authenticate to my wireless network, but I can't ping/resolve/browse anything but google.com Using CLI images - I can't get my network card to auth at all. Any idea what happened - a few months ago wifi was working perfectly. Also - is there anyway to modify the startup job to raise network interfaces to have a time limit? Occasionally boot will go indefinitely.

I am running Armbian_4.5_Cubox-i_Ubuntu_trusty_3.14.54 on a CuBox i4 Pro. The application is a security camera server and the current test environment consists of the server and two IP cameras set to 320x240 and running at 5 fps. The server is receiving these two streams over the Ethernet interface constantly but the data rate is pretty low. I am seeing the Ethernet interface fail after 24 to 48 hours with the syslog entries shown below. After the failure I can restart the link with ifdown/ifup and it works fine. Has anyone else seen a similar issue? Oct 29 11:56:09 localhost kernel: [ 0.505433] libphy: fec_enet_mii_bus: probed Oct 29 11:56:09 localhost kerne…

Hi, I have an issue on my hummingboard i2ex. I installed mpd and configured it with SPDIF. The kernel is 4.9.12-cubox. Unfortunately the sound looks strange. It sounds like a slow motion recording. The load is very load (<0.2) so I think it is not a performance problem. I saw there was an issue with the SPDIF previously but it is a little bit different. Do you have any idea what could be wrong? Is it possible to test it your side? Thanks, Warter

I am unable to boot the latest armbian version on my hummingboard using a MicroSoM i1 rev. 1.5. It seems to be an DTB problem. The boot error is "no valid device tree binary" Does anybody have the same problem or a solution?

I've recently upgraded Armbian on my Cubox-i using apt, i.e. that was not a new clean install. As a result I still have an old kernel running. What is the right way to upgrade kernel? Edit: updated using armbian-config, everything seems to be ok.

Hello, I had three power outages in quick succession, I think the second or third one caught the cubox while rebooting. It won't start anymore. I attached pictures of what I see when plugging it into a TV for catching it's messages. How can I unbrick my system without losing all my work on the SD card? I saw how-to-unbrick-the-system, but I'm not sure where to download which files, since I'm not sure if I have NEXT, mainline or legacy installed. Does that even matter at this point?

hey, is there anyone who successfully compile armbian kernel with can support for uddo quad board ? (i also preffer compiled iptables module) here is my working patch with yocto project version dora http://pastebin.com/BF2SeWHa

I finally got my Udoo Dual up and running with Mainline 4.4 Xenial Next and I was wondering how I go about getting the arduino environment back on to it. I downloaded the arm version from arduino and it sees the correct serial port but how do I access it within arduino. I updated the board package to include the Udoo boards but when I hit upload, it says bossac tools are unavailable for my board? What do I need to do to fix this? Sent from my iPad using Tapatalk

Hi There ! Finally managed to Get the Cubox up& running well . Upgraded from Wheezy to Jessie . Still Stock 3.14.14 Kernel. Well, next step: The graphics card/hardware acceleration. Is there a quite straight "Do this,get that, then do that" howto to get it working ? Thanks so far! ###edit### Things are geting quite weirder today. Did a further SD-Card with Cubox-i_Debian_2.6_wheezy_3.14.14 to get GPU-Suppport by the Wheezy releases . corrected sources: deb http://repo.maltegrosse.de/BSP:/Cubox-i/Debian_Wheezy/ ./ deb-src http://repo.maltegrosse.de/BSP:/Cubox-i/Debian_Wheezy/ ./ apt-get update / upgrade Did apt-get install…

Hello Igor, thanks for your work. On your Github-page for Kernel 4.2.0 you say you tested this kernel with chromium egl. Which was your setup? (Did you build your own chromium? which distro did you use?.....) regards Florian

So I downloaded Armbian Stretch image here https://www.armbian.com/hummingboard-2/ and dd it onto an SD Card. As it didn't produce any output during boot after 'uncompressing kernel' I had to add 'console=both' into the armbianEnv.txt. After that I could see that I land into (initramfs). It looked like it couldn't see the rootfs for some reason. So additionally I've changed rootdev to 'rootdev=/dev/mmcblk0p1' in the armbianEnv.txt. Still the same problem here is the full boot log https://pastebin.com/K64xKHBd What am I doing wrong? 2. Provided that the problem above is easy to fix, how do I start a script after the first boot? S…

I'm trying to upgrade from Armbian 5.32 (Xenial Next/4.4.76) and was hoping to enable 1 wire again on my Udoo. For that build, I had to add one wire modules to the kernel config, then edit the imx6qdl-udoo.dtsi to set the onewire status to okay (from disabled). In the dtsi, after udoo_ard: udoo_ard_manager it had: onewire@0 { /* example for pin 08 */ compatible = "w1-gpio"; pinctrl-names = "default"; pinctrl-0 = <&w1_gpio_pins>; status = "disabled"; /* "okay" to enable */ gpios = <&gpio1 21 0>; }; and in iomuxc, there was a section (in external_hog: hoggrp-2, MX6QDL_PAD_SD1_DAT3__GPIO1_IO21 0x800…

I'm currently working on getting a custom kernel (5.4 kernel which was modified for a specific need regarding containers) running on a Jetson Nano. I've tried running the kernel image on NVIDIA's Jetpack but that didn't work. I've tried building the image directly on the Nano running Armbian and it hasn't really worked so far. It seems to either brick the Nano or not update the kernel version after an install (depending on if I replace /boot/Image). Would you all have any suggestions of what I can try or if it’s even possible? Thanks in advance!

Hi, when booting Armbian Sid minimal rolling 6.1.11, there is no serial console login. Console output: Found U-Boot script /boot/boot.scr 1993 bytes read in 146 ms (12.7 KiB/s) ## Executing script at 12000000 93 bytes read in 94 ms (0 Bytes/s) 38318 bytes read in 2603 ms (13.7 KiB/s) 33621022 bytes read in 3482 ms (9.2 MiB/s) 11215360 bytes read in 1257 ms (8.5 MiB/s) ## Loading init Ramdisk from Legacy Image at 14800000 ... Image Name: uInitrd Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 33620958 Bytes = 32.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flatte…

got this message during build (during installation of additional packages: bridge-utils): [ error ] Installation failed initctl: Unable to connect to Upstart: Failed to connect to socket /com/ubuntu/upstart: Connection refused invoke-rc.d: unknown initscript, /etc/init.d/systemd-logind not found. dpkg: error processing package libpam-systemd:armhf (--configure): subprocess installed post-installation script returned error exit status 100 Processing triggers for libc-bin (2.19-0ubuntu6) ... Processing triggers for sgml-base (1.26+nmu4ubuntu1) ... Processing triggers for ureadahead (0.100.0-16) ... Errors were encountered while processing: libpam-systemd:armhf E: Sub-…

I bought several modules with mpc8308 on board. But following the documentation, i did not manage to implement DMA data transfer. Is it possible to get an example of the implementation of data transfer over DMA?

Until now, the path '/sys/class/leds/imx6:red:front' was used to control the LED on Cubox. Since the last update the path no longer exists. Anything I can do?

I need help please, I am working on NanoPCt3 board based on Armbian_5.83_Nanopct3plus_Ubuntu_bionic_next_4.14.115_desktop I put static ip to eth0 and when i try to ping the output in not stable: 64 bytes from 104.27.115.15 (104.27.115.15): icmp_seq=1 ttl=58 time=580 ms 64 bytes from 104.27.115.15 (104.27.115.15): icmp_seq=2 ttl=58 time=120 ms 64 bytes from 104.27.115.15 (104.27.115.15): icmp_seq=3 ttl=58 time=350 ms and then the output: Destination host unreachable. Destination host unreachable. Destination host unreachable. and i think there are some issues in kernel drivers related on Ethernet or ipv4 so could y…

Hi: I recently installed Buster xfce desktop on Cubox i4pro. Everything works great, except I can not power off cubox. I tried various commands, shutdown -h now; systemctl poweroff; and hatl; but the system first appears to halt, where I can not ping the ip addrss of cubox, but then it reboots. Is there some way to powerfoff cubox? My current system is nightly, but I also tried stable with latest kernel. $ uname -r 5.10.21-imx6 $ cat /etc/os-release PRETTY_NAME="Armbian 21.08.0-trunk.26 Buster"

I've got a Cubox-i 4 running Armbian stretch 4.16.8 and I noticed that the frequency never seemed to drop below 996MHz (even when on zero load) using sudo cat /sys/devices/system/cpu/cpufreq/policy0/cpuinfo_cur_freq whereas armbianmonitor -m showed the same, occasionally showing 792MHz. Looking at Orange Pi Zero I managed to see what the issue might be. Changing /etc/default/cpufrequtils to "powersave" dropped the frequency to 396MHz but stayed there even when under stress (stress -c 4 -t 60). Changing the value to "conservative" gave me what I wanted. 396MHz with no load, rising to 996MHz when under load. Hopefully others might find th…

Hello, I'm trying to get working my NanoPi Fire3 with HD702 screen and I found out some issues. I'm running Armbian_20.02.7_Nanopifire3_bionic_legacy_4.14.174 image on it. -- First and most significant is that the ethernet port isn't working properly. I cannot ping anything and if I try to deactivate and activate ethernet connection in Network Manager it says: Error: Connection activation failed: IP configuration could not be reserved (no available address, timeout, etc.) Mar 31 14:04:05 nanopifire3 NetworkManager[3061]: <warn> [1585663445.9567] dhcp4 (eth0): request timed out Mar 31 14:04:05 nanopifire3 NetworkManager[3061]: <info> …

Hi, I tried to download CLI-ubuntu and Desktop-Debian archives, then i did like described in manual: sudo dd if=Armbian_4.5_Cubox-i_Debian_jessie_3.14.54_desktop.raw of=/dev/rdisk2s1 bs=1048576 or sudo dd if=Armbian_4.5_Cubox-i_Ubuntu_trusty_3.14.54.raw of=/dev/disk2s1 bs=1048576 When i try to use that on my cubox i-pro - nothing happend: TV connected via hdmi and i see only black window I had ubuntu 12 installation on the same sd-card, i have backup of it and i can restore from backup (everything works fine). But how i can use the new one kernel, created here? Ps. sd-card: 4Gb, cubox-i pro, mac os.

Hi i have an udoo quad and i downloaded your os (ubuntu jessie desktop Kernel 4.0.8). At first congratulation for your work and big thanks to share it After the flash of the sd card (used win32diskimager because imagewriter don't work for me), i can started my card. Ethernet, wifi, browser ... works fine ! Now, that it didn't work is sata disk or usb disk. When i plug it on the card nothing appear. If i go to /media i saw nothing. Do you know how to resolve this ? Otherwise, i would like to compile Qt5.5 but i need the header for openGL librairie to do it. Is it possible to have it (i saw nothing on /usr/include) ? Last think, do you plan to make a try with the new …

Trying to debug this issue. Everything was fine until a recent reboot and now the box is stuck in a boot loop with any supported image downloaded from armbian. I've been focused with debian but the ubuntu doesn't work either. I have tried 3 different microSD cards (samsung and SanDisk) with the same result. I've tried the steps in https://docs.armbian.com/User-Guide_Basic-Troubleshooting/ https://docs.armbian.com/User-Guide_Recovery/ but it appears that the there is something going on with the Linux kernel? changing the verbosity doesn't provide any new information. I have even tried 20.05.1 and still the same behavior. Any though…

Dear all, I'm just trying to get a HummingBoard-Edge (i.MX6 Quad, 2GB) working with Armbian_5.20_Cubox-i_Ubuntu_xenial_4.7.3. Unfortunately, the board is recognized as CuBox-i, U-Boot loads the wrong dtb file (imx6q-cubox-i.dtb) and I have no access to the internal eMMC card (mmcblk1). By the way, it's the same issue with ArchLinuxArm. Do I have to somehow modify the U-Boot environment variables to get the board being recognized as Hummingoard2? Do you have any other ideas? Thank you very much for your help! Best regards Andreas

Wheezy: deb http://repo.jm0.eu/BSP:/Cubox-i/Debian_Wheezy/ ./ Repository is online but installations is untested by me.

the system in my cubox-i 4x4 crashes after updating to kernel 4.4.1. I did the update in the system and after rebooting it doesn't work. I upload the screenshot of the only thing I get, after that the screen goes off, nothing else happens. If the problem is the new kernel it means I can't upgrade it, is it right? I also try new images 5.0 Vanilla and I get the same screen.

Maybe someone has an idea what the problem is... So I use the latest armbian with kernel 4.9.18. I installed mpd+mpc on it and mounted nfs share with fstab. Everything is working fine but if i press the play button from my phone/tablet actually the playing starts just after 30 sec. it is exactly 30 sec. I have no idea what can cause this delay.

Recently I took my old Hummingboard and to run Armbian on it. I chose the desktop-version for Hummingboard using mainline kernel (presently 4.11.6-cubox). Unfortunately Armbianmonitor shows high CPU -temperature. It gradualy builds up, starting from 50 degrees next to 70 degrees, eventualy approaching 85 degrees and then it shuts down. I use the passive heatsink that came with the board and no case. I use it for light desktop things like browsing the internet. Is there something I can do to prevent this, is there something in the kernel like throttling when the board reaches a certain temperature? Thanks again for a great OS, I think you are doing an outstanding…

Hello everyone! I just installed Armbian for my Cubox and I'm experiencing a boot loop caused by the watchdog directly after logging in as root and when prompted to create a new account. Attached you find the serial console output. Does anyone have any idea what could cause this behaviour? Cheers, David Cubox-i4Pro Boot Loop.txt

Hey all, I have been fighting this for 2 days now thought I would reach out for some help. I have a Intel Wireless 7260 PCIe in my Hummingboard Pro board. I can run iwlist wlan0 scanning and see my wifi access point no problem. However when I run dhcpclient wlan0 I never can connect to my access point. This is my /etc/network/interfaces file. # Wireless adapter #1 auto wlan0 allow-hotplug wlan0 iface wlan0 inet dhcp wpa-ssid "myssid" wpa-psk "mypassword" auto lo iface lo inet loopback I have also tried a USB wifi adapter to attempt to rule out the PCIe bus being the issue. However neither will connect. If anyone knows what to do from here I would be e…

Hi, I run ARMBIAN 5.25 stable Debian GNU/Linux 8 (jessie) 4.9.12-cubox and use an external DAC connected to USB. Additionally and or comparison purposes I use ARMBIAN 5.25 stable Debian GNU/Linux 8 (jessie) 4.4.51-udoo . Since a few days the kernel on the cubox doesn't seem to recognize the USB-DACs as sound device any more. So, "aplay -l" doesn't list it: aplay -l **** List of PLAYBACK Hardware Devices **** card 0: SPDIF [Integrated SPDIF], device 0: S/PDIF PCM snd-soc-dummy-dai-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 A test with a udoo-board, shows the expected output: aplay -l **** List of PLAYBACK Hardware D…

I have followed all threads dealing with this topic but got no where so maybe... just maybe someone has made it work somehow? I have armbian (Armbian_23.02.2_Rk3318-box_bullseye_current_5.15.93) installed on a TV box with a Rockchip RK3318 inside it. I am using a microsd card and EVERYTHING is running wonderfully! I have also attached a 500GB USB hard disk (output from fdisk-l) Disk /dev/sda: 465.76 GiB, 500107862016 bytes, 976773168 sectors Disk model: 5000BEV External Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes I ran armbian-config a…

This post is, more or less, a continuation of something I started here, but adapted to Armbian. I will start with an overview of what I have done (maybe this is relevant) and finish with my questions. What I've done: I have a Hummingboard Gate with a Mikrobus RS485 click 3.3V (this one: https://www.mikroe.com/rs485-33v-click). In order to make this work I need to change a few things in de device tree. The dtb that my board uses is 'imx6dl-hummingboard2.dtb' so I copy that file to my home directory for safe keeping. cd ~ sudo cp /boot/dtb-4.19.18-cubox/imx6dl-hummingboard2.dtb . Then I convert this dtb to a dts: sudo dtc -I dtb -O dts -o im…

Hi everybody, I'm new here and I would like to ask you for help with make armbian work on other board - Toradex Colibri iMX6DL with freescale iMX6 processor. They already have U-boot & Angstrom linux on NAND (where I would like to get armbian). They have meta-packages and images available for download on their website and I would like to know what is the best way to make it work (to keep their HW configuration)? I like these boards because of good desing and good HW, but this Angstrom linux isn't good... Thank you for every advice

Hello, I'm newbie on freescale imx6. I've just bought a hummingBoard2 rev1.4. A modem SIMCOM7600E mcpie is attached. When I used ignition and install debian, it's works but I 've a problem with the driver of this modem, the WWAN is not configured. ATCOMMAND works fine but I would like to use it by wwan interface and I didn't know how to put the driver file.c! I decided to install armbian_5.38 debian or ubuntu but my hummingboard doesn't boot. The autoboot stop at ##Flattend Device Tree blob at 18000000 Booting using the fdt blob at 0x18000000 after this I had "No signal" on my HDMI screen. I use a µSDHC1 Transcend 8Go. She is erased by SDFORM…

Hi, When I tried booting the vanilla kernel, downloaded from http://www.armbian.com/hummingboard/, on my Hummingboard i4 Pro, I get the following error message from u-boot: ERROR: Did not find a cmdline Flattened Device Tree Could not find a valid device tree Booting from net Has anyone else seen the same issue? Thanks.

I am trying to compile the full OS image (incl. kernel and u-boot) for nanopifire3 target but fail every time. I am following the provided build instructions. I have tried compiling on multiple machines, but the one I am using has 8 cores and 12gb RAM. I have tried in an Ubuntu 22.04 LXC container, Ubuntu 22.04 in a VM, and the the docker container provided by Armbian. My kernel has the binfmt_misc module loaded (verified with lsmod), no spaces are present in build path, and I have tried both root user and sudo as a regular user. I have also checked the similar issues on the armbian forum Please forgive me if anything is incorrectly formatted or so, I have…

Hi there ! Quite nooby again - about 10 years off from the deb-world - i beg for patience. Actually three issues: 1. Ultrawide Screens : 2560x1080 @60 (LG 25UW) via HDMI. Got it working on Raspbery (Overclock cpu+GPU/ mod of PixelPipe/ Mem of GPU) How to achieve this on Armbian Wheezy od trusty Desktop ? boot.cmd is ignored (already tried to mkimage it to /boot/boot.scr 2. Wlan Performance Wlan performance unter Wheezy was quite Poor , known issue ?? security.debian.org - gpg-errors with repo - that was funny enough to get started with.. 3. Tried Armbian trusty Desktop. Loads. No Desktop.No Start X? How to get rid of this Prob ? (Whats the…

Hi guys. I can't get the headphone jack to work on the NanoPC T3+ on Armbian 5.44 Bionic. HDMI sound works. There's a second Built-in Audio, but nothing seems to work. Also the on-board microphone doesn't work. I've tested it on the friendlyArm Lubuntu and there it both works. Additional. Can somebody point me into the right direction where to add a higher cpufreq in available frequencies? At 1400Mhz it only reaches 55°C maxed(with fan). Single core performance is bad. So some overclock would be helpful. Otherwise Armbian works great. Thank you. NicoD

Hi all, In the review of the Fire3 at least one person mentions powering this board via something other than the MicroUSB. This would allow me to use the serial console that's supposedly exposed over that port instead of wiring up yet another USB to serial converter. What I can't work out is a) which pin/s are used to power it, and b) what kind of power supply is used. I'd rather not fry the board (it'll do that itself under load) so can someone point me in the right direction? Thanks in advance.

Hello, Recently I bought a nanopi fire 3 and installed armbian without any issue (Armbian_5.91_Nanopifire3_Debian_buster_next_4.14.133). The first thing I did was to connect the nanopi to my ADSL router in order to complete the basic configuration. Everything worked fine. Then I connected the nanopi to an Edimax gigabit ethernet switch and here is where the network problems appeared. The ethernet connection was too slow, with ping times of more than 1000ms, and an unstable behavior that made it almost impossible to connect via ssh. 64 bytes from 192.168.22.12: icmp_seq=1 ttl=64 time=1004 ms 64 bytes from 192.168.22.12: icmp_seq=2 ttl=64 time=1…

Hi, I just installed last ubuntu, iso 5.38, and the system says I only have 2GB RAM instead of 4GB. How can I fix it? Also, in the armbian-config, I can select board configuration, but I don't know what I should choose... Cubox-i dual/quad...... v1.5...... with emmc.... ?? Thank you.

Hi Sir/Madam, I am using Humming bard Gate for testing, i am trying to interface a minipcie of 4G module L718 from Fibocom. I am using Armbain platforn for testing. i am unable to interface the Module and use the module to access internet(Use as mobile broadband). Kindly support

Hi there, Just loaded Armbian Vanilla Jessie (5.00, 4.4.1 kernel) on one of my Cuboxes. There's no sound from SPDIF, even though it's seen: root@cubox-i:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: SPDIF [integrated SPDIF], device 0: S/PDIF PCM snd-soc-dummy-dai-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 Speaker-test shows no errors: root@cubox-i:~# speaker-test -r 44100 -F S16_LE -c 2 -D hw:0,0 speaker-test 1.0.28 Playback device is hw:0,0 Stream parameters are 44100Hz, S16_LE, 2 channels Using 16 octaves of pink noise Rate set to 44100Hz (requested 44100Hz) Buffer size range from 64 to 16384 Period size range from 32 to 8192 …

Hi, i'm quite new to Linux and the cubox. I have just installed my cubox 4x4 and downloaded armbian. All works but a can only see 2GB of the 4GB memory

Hello, I am using clean 2.9 jessie build on Cubox-i. I am planning to move from 1*bare sata HDD boot to 2*sata HDDs with lvm mirroring. Somebody had tried to boot from lvm on such devices? Is it works out-of-box or need some tweak? Thanks, Yuri.

Any hints?

Gent's, I try to get a image build the last days, but when the image was created, it fails booting. On some other try's, it didn't build. Has in the last time someone build a image ? And is it booting ? :-) Thanks Peter

Hello, I deployed the latest image "Armbian Buster mainline based kernel 5.8.y" and after initial setup, I cannot activate the analog sound card. What I did: The "Hardware" section in "Settings" section of armbian-config was missing, so I installed the following packages: "linux-dtb-current-sunxi/buster 20.11.0-trunk.28 armhf Linux DTB, version 5.9.5-sunxi, linux-dtb-dev-sunxi/buster 20.11.0-trunk.28 armhf Linux DTB, version 5.10.0-rc2-sunxi" and after that changed: /boot/armbianEnv.txt by adding overlay_prefix: "sun8i-h3". This was the only way I could make armbian-config to correctly display the "Hardware" device tree. I tried to put: i…

Hi Igor ! We have a problem with i.mx6 when ambiant temperature is too high or when CPU is too busy. The CPU frequency don't scaling with the temperature CPU, so the System Crash. Can you had thermal sensor on Cpu scaling ? by add it on kernel ? Thanks

How to Reset armbian 24.5.1 jammy, the device long time I not power on, but just now I power on can't log with ID Root & Password 1234. already many things still can't resolve it. If have any suggestion please let me know.

Hello, I've flashed several times last image from cubox-i but I have this: Wrong image format for "source" command file not found /boot.scr file not fougn /uEnv.txt file not found /zImage file not found /uImage ..... ERROR: Did not find a cndline Flattened Device Tree Could not find a valid device tree ..... And more ¿Whats wrong? Thanks

When cubox is configured to run wifi, it takes 60+ seconds for it to start up with no network cable plugged in. Where as when I plug in a network cable to the network port it will start up under 10 seconds. Hardware: Cubox-i4 Pro Running Ubuntu Trusty image found here: http://www.armbian.com/cubox-i/ Any advice would be appreciated.

Thought this module was included in the kernel. I can install the iscsi client software, but obviously, no good without the module. Will it be included in the future? Cheers

Hi Friends Recently I have been trying Armbian 23.5 as alternative for NVIDIA official images. Tried both Ubuntu Gnome desktop and Debian Cinnamon desktop builds but somehow non of them discovers HDMI output. When Jetsno Nano is booting up I can see official "NVIDIA" screen for a while and then information about missing input (from TV on a TV). The hardware itself works OK - when I change SD card to one with an official image or another one with Debian 11 official - it works just fine. It's seems like a problem with Armbian build itself. Any advice is much appreciated. Kuba Logs: https://paste.armbian.com/omiher…

Hi, I'm so happy to growth of Armbian, and its good to see that you adding new devices to your device support cartela. But I couldn't find CSC image for Tinkerboard 2. Is that uses same image with RockPi N10 or did you forget to add to download page under to CSC images lists. Bests,

Wondering if it is possible to replace pfsense (freebsd 14) with Armbian on a netgate sg-2100 appliance? https://shop.telappliant.com/product/sg-2100-pfsense-security-gateway-appliance/ I have the version with an additional 32GB M.2 SSD and it looks like the mvebu_armada-37xx board is supported by the generic Armbian, but I struggle to get from u-boot to starting the installer from usb (used the Armbian_23.5.1_Uefi-arm64_bookworm_current_6.1.30_minimal.img), with the usbboot command. Below is the current u-boot environment. I have masked some parts with "xxxxx" and probably won't need half of these variables, as they are very vendor specific, for example netgateid etc…

I have a Cubox-i (older 2GB version) running Armbian_5.00_Cubox-i_Debian_jessie_4.4.1.zip. It's using a SATA drive as root. I've installed some services that take up a lot of CPU. After a couple of days, it still responds to pings, but I can no longer log into the box with SSH. I'm forced to power cycle it to log back in. Looking at it, there's nothing in the logs to point to the problem, the only weird thing in /var/log/messages is: Feb 22 12:34:47 localhost rsyslogd-2007: action 'action 17' suspended, next retry is Mon Feb 22 12:36:17 2016 [try http://www.rsyslog.com/e/2007 ] I do wonder if it's overheating due to the CPU use. Is there anything I can do to tra…

Hi I have spent a lot of time with the Hummingboard2 Edge over the last months and i would like to share my experiences here. My Configurations is: Hummingboard 2 Edge with SSD Sata and MC7304 PCIE Lte Modem. Carrier Board is V1.2. Microsom is version 1.5. They are available since end of 2016. The difference is the WLAN and Bluetooth Module. Solidrun has changed it from Broadcom to TI Wlink 1831. First of all. If you have an unfused Microsom and you want to use the bootjumpers. (Only Carrier Board V1.2) Boot from SD: Set Jumper to SD (J5005 Pin 7 and 8) and (Connect J23 Pin 11 with J24 Pin 2 and with J21 Pin 5 Boot from MMC: Set Jumper…

Hi. I had to force my way through the upgrade script working. I haven't rebooted yet, but I'm crossing my fingers . Here are the three issues: 1. cubox-i shows as "unsupported" and the script dies. /proc/cpuinfo shows: Hardware : Freescale i.MX6 ... ...which isn't in the list in the script. 2. The script crashes and can't handle the situation where the apt-get upgrade prompts you about configuration files. For example, my /etc/bash.bashrc was different than the packaged version. The script won't take input and hangs. I see the "-y" in the script, but for some reason it doesn't seem to work right. 3. /boot/script.bin - a symlink is made to a none…

Hey Folks, After the Solid-Run screen I lose HDMI, serial works fine of course. Assuming the Cubox can't use my resolutions by default but I have no idea how to fix. Could anyone please point me in the right direction? $ xrandr Screen 0: minimum 320 x 200, current 1920 x 1200, maximum 16384 x 16384 VGA-0 disconnected (normal left inverted right x axis y axis) HDMI-0 disconnected (normal left inverted right x axis y axis) DVI-0 connected primary 1920x1200+0+0 (normal left inverted right x axis y axis) 518mm x 324mm 1920x1200 59.95*+ 1920x1080 60.00 1600x1200 60.00 1680x1050 59.88 1280x1024 60.02 1440x900 59.90 …

Could someone list the differences between the i.MX6 based CuBoxes? I've seen this ones mentioned: CuBox-i1 CuBox-i2 CuBox-i2eX Cubox-i 4x4 CuBox-i4Pro CuBoxTV Are there more?

Hi everyone. I am using Debian Jessie image for hummingboard IMX6. I compiled version 0.12.0 of https://github.com/Freescale/gstreamer-imxand installed it. I can use imxipuvideosink just fine. However, I can't get imxg2dvideosink working. When I try the following pipeline: gst-launch-1.0 videotestsrc ! imxg2dvideosink I get $ sudo gst-launch-1.0 videotestsrc ! imxg2dvideosink Setting pipeline to PAUSED ... Pipeline is PREROLLING ... Message from syslogd@localhost at Jun 1 15:40:46 ... kernel:[ 1815.922228] Internal error: Oops: 5 [#4] SMP ARM Message from syslogd@localhost at Jun 1 15:40:46 ... kernel:[ 1815.922381] Process videotestsrc0:s (pid: 2506, stack limit = 0…

Hi, I am making Asterisk PBX over Orange Pi - 2g IoT, I have tried Armbian as well as Ubuntu. Everything is working fine, but I am stuck on two issues, a. How to add built-in GSM module of Orange Pi 2g IoT board in asterisk, so that A GSM trunk call/text can be transferred on SIP extension. I know chan-dongle, but asterisk is not detecting GSM module. I ahve tried different versions of asterisk. b. How to change IMEI of Orange Pi 2g IoT Looking for solutions Regards

Hello everyone! I'm trying to install nvidia graphic card driver to the Jetson Nano after I successfully started bookwork on it. I have nouveau running and I don't understand how/if it is possible to switch to nvidia one. Can you guys please help me to understand whether it is possible at all? Am I missing something? Probably was Googling wrong keywords. For now I understand that Nvidia SDK supported by nvidia requires too old version of their ubuntu-based l4t linux which I don't like at all.. Thanks in advance!

Hello everyone, I am a beginner in Linux. I have a Hummingboard i2ex and I am running Armbian_5.30_Cubox-i_Ubuntu_xenial_4.11.4_desktop on it. Trying to use a CSI Tool, I have to compile and install this kernel : https://github.com/xieyaxiongfly/Atheros-CSI-Tool.git Here are the steps that I did on the Hummingboard: ( you can see the tutorial: http://pdcc.ntu.edu.sg/wands/Atheros/document/Atheros-CSI-Tool-User-Guide.pdf ) 1) sudo apt-get install git (to clone the source) 2) sudo apt-get install libncurses5-dev libncursesw5-dev (to run makemenuconfig) 3) git clone https://github.com/xieyaxiongfly/Atheros-CSI-Tool.git 4) Enter the dir ~/Atheros…

Hi, I installed Debian wheezy I tried to connect via ssh with ethernet connection and it works well , but if I try to connect with the wifi connection is blocked after entering the password , it is a bug cubox? . If you can serve the ouptu ssh -vvv it is : marco@kali:~$ ssh -vvv 192.168.x.x OpenSSH_6.0p1 Debian-4+deb7u2, OpenSSL 1.0.1e 11 Feb 2013 debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 19: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 192.168.x.x [192.168.x.x] port 22. debug1: Connection established. debug1: identity file /home/marco/.ssh/id_rsa type -1 debug1: identity file /home/marco/.ssh…

Hello, I installed rpi-monitor via the debian micro home server script. It's nice, especially cpu load and ram usage but I don't get the right temperature of the cpu. Here's a screenshot. Any idea how I can fix that?

I installed a TPLINK wifi dongle, but when trying to set the interface up, i get the message of the subject. What can it be? Thanks! root@kraken:/etc/nginx/sites-enabled# ip link 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,DYNAMIC,UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000 link/ether d0:63:b4:00:1d:57 brd ff:ff:ff:ff:ff:ff 3: wlan1: <BROADCAST,MULTICAST,DYNAMIC> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000 link/ether c…

I've tried two releases of Armbian for the Jetson Nano and was struggling to get SPI enabled on the Jetson. To check if SPI is enabled, I've been reading its status is through: cat /proc/device-tree/spi@7000d400/status which just returns disabled Here's what I tried: - enabling spi-spidev through armbian-config, but this option doesn't exist in armbian-config as it does for other releases for devices - making a custom device tree dts file and pointing extlinux.conf to it (below is the relevant snippet): spi@7000d400 { compatible = "nvidia,tegra210-spi\0nvidia,tegra114-spi"; reg = <0x00 0x7000d400 0x00 0x200>; inte…

Hello everone. I'm new to embedded linux. To start with, I have nanopi fire 3 and smart 6818 cards, but I cannot access gpio pins with any gpio library. Why doesn't the NPi-GPIO library work with these cards? At first I was using the lubuntu version, I tried a lot there, but I couldn't. Now I'm trying to do something using armbian version 21.04. I'll post the problem I'm facing below. Thank you in advance for your help. Traceback (most recent call last): File "npigpio.py", line 1, in import NPi.GPIO as GPIO File "/usr/local/lib/python3.7/dist-packages/NPi.GPIO-0.5.8.6-py3.7-linux-aarch64.egg/NPi/GPIO/init.py", line 1, in from NPi._GPIO import * Runtime…

Need help in finding a suitable Debian build for Sabre Board running imX6 Quad from Freescale.

First of all, sorry if I'm asking something really obvious, but I'm new in Linux. Hi! I just have a new fresh install of Armbian Stretch on my Cubox, and I just realized that Armbian isn't using the Predictable Network Interface Names but the old one. root@opl-cubox:/home/lpuerto# ifconfig eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.1.6 netmask 255.255.255.0 broadcast 192.168.1.255 inet6 fe80::d263:b4ff:fe00:8297 prefixlen 64 scopeid 0x20<link> ether d0:63:b4:00:82:97 txqueuelen 1000 (Ethernet) RX packets 411 bytes 50456 (49.2 KiB) RX errors 0 dropped …

Dear Armbian community I want to run klipper on my ordoid n2+ I started out using a default ubuntu os from odroid themselves but it was missing a ton of drivers I need. everything worked on that image except for the drivers. Someone mentioned Armbian to me. I got everything running except I now have a new issue. I am using klipperscreen a simple gui with touch controls. before installing I could use my screen without issues and I installed everything on the screens terminal. Now that klipperscreen is installed I see the boot sequence and than the signal gets lost. I already checked the klipperscreen guides and forums and if it doesnt report errors its the…

I'm thinking of getting https://www.beagleboard.org/boards/beagley-ai I see there is this page for it https://www.armbian.com/beagley-ai/ I also see references to it in the code: https://github.com/search?q=org%3Aarmbian+beagley&type=code Are there any pre-built images available for it? Or would I have to build one?

Hi there, on my Cubox i4 pro there was an update from 4.9.7-cubox to 4.9.12-cubox. It took quite a while, and there were a couple of messages: dpkg: warning: unable to delete old directory '/usr/src/linux-headers-4.9.7-cubox/scripts/genksyms': Directory not empty dpkg: warning: unable to delete old directory '/usr/src/linux-headers-4.9.7-cubox/scripts/mod': Directory not empty dpkg: warning: unable to delete old directory '/usr/src/linux-headers-4.9.7-cubox/scripts/kconfig': Directory not empty dpkg: warning: unable to delete old directory '/usr/src/linux-headers-4.9.7-cubox/scripts/basic': Directory not empty dpkg: warning: unable to delete old directory '/usr/src/…

I exposed my cubox to the WAN and some **** has hacked me and changed my root password, how can I reset it? I've tried hitting shift on boot but I don't get a grub menu. I'm using the debian jessie image. Thanks, Jack

Hi Guys, First thanks fo rthe hard work, but as in other threads here every now and again we get an issue moving up kernel versions. Mostly this is a post to flag up I had issues, so might you and that reverting the kernel fixed it for me. I did an apt-get update; apt dist-upgrade (I run this every other day normaly) and it did a kernal update from Linux cubox 5.9.14-imx6 #20.11.3 SMP Fri Dec 11 20:57:51 CET 2020 armv7l GNU/Linux to Linux version 5.10.12-imx6 It appears to all work.... however I use my Cubox-i to be a server for Kodi. When I play flac files (which are quite big) it down loads th…

I would like to run a vanilla/mainline debian kernel on my cubox-i4pro but apparently there is no image available for download. Is that be because the vanilla kernel is not supported or nobody has yet build one?

Here's what I get when trying to boot (data is from my serial adapter): I2C_WriteByte nack returned I2C Device Address Write Abitration Error I2C_WriteByte nack returned I2C Device Address Write Abitration Error I2C_WriteByte nack returned I2C Device Address Write Abitration Error I2C_WriteByte nack returned I2C Device Address Write Abitration Error Wakeup Sub CPU 1234567 CPU Wakeup done! WFI is expected. CPU0 is Master! U-Boot 2016.01-armbian (Sep 02 2019 - 08:57:37 +0200) DRAM: 1 GiB MMC: NEXELL DWMMC: 0, NEXELL DWMMC: 1 loaded from SD, getting env from MMC 1 *** Warning - bad CRC, using default environment MIPI: display.0 HDMI: display.0, preset 0 (1280 * 72…

Hello Solidrun has updatet their microsoms to v1.5. MicroSOM rev 1.5 Wifi: 802.1 b/g/n - 2.4 / 5 Ghz, single or dual MIMO with Bluetooth V4.0 (TI Wilink 8 WL18xx) http://wiki.solid-run.com/lib/exe/fetch.php?media=imx6:microsom:docs:sr-usom-mx6-pcn-20160915.pdf This is from the solidrun website: Make sure that your kernel .config has the following enabled either as modules or statically part of the kernel, in order to build the TI WiLink8 WiFi drivers -CONFIG_WL18XX=yCONFIG_WLCORE=yCONFIG_WLCORE_SPI=yCONFIG_WLCORE_SDIO=yCONFIG_WILINK_PLATFORM_DATA=yCONFIG_WL_TI=y# CONFIG_WL1251 is not set# CONFIG_WL12XX is not setThe firmware i…

See the following steps to get the TI wl18xx drivers to work on the Cubox with the I4P Rev 1.5 SOM. Step 1) Boot with the Armbian base image (Armbian_5.20_Cubox-i_Ubuntu_xenial_4.7.3). The 3.14.79 base image also works however will require a different dpkg install command to overwrite the 3.14.79 kernel. Step 2) Build a new kernel with Armbian build tools, note this only works with the 'DEV' kernel branch because SolidRun provides all the necessary DTS files. Edit the compile.sh script and change KERNEL_CONFIGURE="yes" to customize the kernel configuration. The relevant modules you will need to select are: CONFIG_WL_TI=y CO…

Hi, I tried everything: I downloaded wheezy isos, Jessie.... with GUI, no GUI and then I installed by myself..... solid-run isos and armbian isos.... just clean system... burn the iso in a sdcard and run the system.... if it has already GUI I install blueman and test bluetooth and wifi.... perfect. If doesn't have gui then I install one (I tried xfce and mate), then blueman and test bluetooth and wifi.... perfect. then 'apt-get update && apt-get upgrade' and bluetooth stops working Any reason for that and any tip?

Hi, I'm trying to generate an Armbian image for a custom board. I generated configuration files for card and family, with the necessary information for u-boot and kernel. I need to have separate boot partition in FAT and I added BOOTFS_TYPE="fat". Using the compile.sh in the Armbian "build" repo I get an image, but flashing it on the sdcard does not start uboot. In the boot partition I find not only the kernel and dtb, but also the u-boot scripts. How do you generate an image that contains everything correctly? Thanks in advance Riccardo

Hello. I have been running Armbian_5.41_Cubox-i_Ubuntu_xenial_next_4.15.7_desktop.img with no issues on my Hummingboard Edge which consists of rev 1.4 Hummingboard2 carrier and rev 1.5 SOM. I decided to try the legacy image (Armbian_5.41_Cubox-i_Ubuntu_xenial_default_3.14.79_desktop.img) to gain support for the hardware video decoder. However, I have been unable to get the legacy version to boot properly. Initially, the board is detected as having a rev 1.5 SOM and there is a message about not being able to find the right dtb file (imx6q-hummingboard2-som-v15.dtb). Looking under /boot/dtb there are no dtb files for the rev 1.5 SOM in the legacy image. So I copied the defa…

I set up NanoPC-T3 as a router, the upsteam Ethernet port is connected to a router. However, the bandwidth drops dramatically whatever I’m using IPTables or network bridge to forward the data. This doesn’t happen on the other SBCs I have. How can I solve it?

Hello, for the past few days I've been trying to install k3s on a Jetson Nano machine with the legacy Kernel 4.9, which I managed to recompile with EBPF support, but it seems there are some Kernel EBPF errors. So, I tried to install Armbian, which also doesn't have EBPF support compiled into the Kernel. I've tried to boot from many images from the Jetson Nano archive on the Armbian site, but none of them work. Is there any documentation on how I could compile the kernel on Armbian - Jetson Nano machine? Why can't I boot from any of the Armbian - Jetson Nano images from the archives? I have updated the legacy OS from Nvidia with the latest drivers boot loaders …

Hi guys. I wanna ditch archlinux because its continuos issues with Kodi and uwsgi. Does Debian for arm play good with Kodi? Is there any major issue besides the network speed? Thanks!

Hello. I've tried to find the TC358743 toshiba chip drivers in the kernel, but I can't. As far as I know they are included from 4.1 version, but in the menuconfig option I didn't found them. Is driver avaliable on this kernel or I should use another kernel?

Is there lvds screen compatible with humming board pro version on armbian and if not wich lvds 30pin will u recomend to modify or assist to work on the HB pro

Hello Igor, First, Thank You for all great work over Armbian ! I tried about all previous releases and they started over HDMI port normally with factory U-Boot 2013 ... Now Armbian 5.00 I tried all posted release Legacy and Vanilla Kernels and only Jessie Desktop show startup process and show GUI screen. Igor, may You help Me Please, How to upgrade factory board U-Boot with Your U-Boot version ?