Other families

Hi, I'm incurring in a issue with updates of the board to Armbian 26.8. The new kernel or updates break the board connectivity gets lost, since the board boots up, the LAN port blinks but it doesn't set any IP Address. The board works in headless mode with the Debian 13 CLI UFS image, so I can't debug it using a monitor. Has anyone the same issue? How to reproduce 1.Flash the recommended Debian 13 Trixie CLI Image from Armbian Website 2.Start the board normally, in headless mode 3.login with ssh 4.set a new user account 5.Run apt update && apt dist-upgrade -y and then reboot 6.Board…

Hi, I'm so happy to growth of Armbian, and its good to see that you adding new devices to your device support cartela. But I couldn't find CSC image for Tinkerboard 2. Is that uses same image with RockPi N10 or did you forget to add to download page under to CSC images lists. Bests,

This post from February 2025 claims that RP5 and RPMini are supported: https://www.armbian.com/newsflash/armbian-v25-2/ however, I can't find them on the downloads page. I also don't currently own an RPMini, I am tempted to buy one but I wanted to make sure it was supported first. What's the state of support right now?

I have a v1.2 Rockpi S with 512MB of RAM, while using the latest Armbian Focal and Buster images (20.08.1 with kernel 4.4.y), I have been experiencing WIFI issues. The device connects to the Access Point and maintains the connection but every minute or two the SSH connection hangs or freezes for several seconds and then comes back and prints everything that when on during the period it was not responsive. When I used the images with the 5.8.y kernel, I did not experience the same issue. In all cases wired ethernet (eth0) is not effected by the issue. Continuously pinging a local system shows the below result. Other WIFI devices on the same network do not experience …

Hello How to rotate screen HDMI ? 4.7.3-cubox

The hummingboard edge has a RS485 port on UART2? What would it take to get to get this running? The latest build does not have ttymxc1 enabled. And I think the driver for the RS485 is different than the normal RS232 Driver. thanks

Hello, I'm developing a Custom Armbian for the RSB-4411 (the motherboard that uses like the Raise3D E2). For the moment, it's in the experimental phase because I can't get it to boot. It goes CRC-ERROR when I boot into the debug port on my motherboard. Source codes Armbian build: https://github.com/AstromanGaming/build Linux Kernel: https://github.com/AstromanGaming/Linux-i.MX-Fork U-boot: https://github.com/AstromanGaming/U-boot-i.MX-Fork If someone or I manage to make it boot, that would be great! 🙂 PS: I'm new to this community, if I do something wrong, please let me know.

I installed a TPLINK wifi dongle, but when trying to set the interface up, i get the message of the subject. What can it be? Thanks! root@kraken:/etc/nginx/sites-enabled# ip link 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,DYNAMIC,UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000 link/ether d0:63:b4:00:1d:57 brd ff:ff:ff:ff:ff:ff 3: wlan1: <BROADCAST,MULTICAST,DYNAMIC> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000 link/ether c…

I'm currently working on getting a custom kernel (5.4 kernel which was modified for a specific need regarding containers) running on a Jetson Nano. I've tried running the kernel image on NVIDIA's Jetpack but that didn't work. I've tried building the image directly on the Nano running Armbian and it hasn't really worked so far. It seems to either brick the Nano or not update the kernel version after an install (depending on if I replace /boot/Image). Would you all have any suggestions of what I can try or if it’s even possible? Thanks in advance!

Hi All, Looking for assistance with getting an old SmartQ5 Mobile Internet Device running with Armbian. I was able to locate Github page (https://github.com/tpruvot/smartq-magicsd) which references booting from SD but need assistance getting armbian compiled and configured for the device. Any help is appreciated! SPECS: Samsung Mobile Application Processor S3C6410 based on ARM11 core at 667 MHz/800 MHz 128 MB DDR 133/333 MHz SDRAM 1 GB NAND FLASH (256 MB usable for storage) AC97 audio codec & PCM 24-bit audio SoC graphics unit, OpenGL ES 1.1/2.0, 4M triangles/sec @133Mhz (Transform only) Integrated Wi-Fi 802.11b/…

I am using your Debian (jessie) on the new SolidRun Hummingboard-Edge board. [Linux cubox-i 3.14.14-cubox-i #8 SMP Sun Jul 12 19:03:09 CEST 2015 armv7l GNU/Linux] I am planning on using the RS-485 on the board that is tied to UART2. But I noticed that ttymxc0 (UART1) and ttymc3 (UART4) are the only tty ports that have drivers associated with them. [ "dmesg | grep tty" ] How can I turn on the driver that is associated with UART2 (ttymxc1)? Thanks,

I am unable to boot the latest armbian version on my hummingboard using a MicroSoM i1 rev. 1.5. It seems to be an DTB problem. The boot error is "no valid device tree binary" Does anybody have the same problem or a solution?

the current filogic kernel has no info [in github] for where it was forked from, and trying to apply incremental patches from kernel.org I found it contains pieces of 6.14 in an ostensibly 6.12 branch. @chainsx might you be able to divulge where you forked it from?

Hello everyone, just wanted to let you know, upgrade from Armbian Ubuntu 5.38 to 5.44 caused problems on my Cubox-i4Pro. - Armbian Ubuntu 5.38 headless (no display connected to Cubox-i) worked perfectly, there were no issues with anything. - Upgraded Armbian Ubuntu 5.38 to 5.44 (apt-get) and rebooted - After reboot, no audio was sent to my audio amplifier (through Toslink optical cable) by Shairport-Sync 3.1.7 (AirPlay emulator). Airplay was visible on my iOS devices (iPad, iPhone) and audio was streamed from iOS to AirPlay, but no audio was sent by Cubox-i to the optical connection to my audio amplifier. - Removed the Shairport package usi…

I have debian installed on my hummingboard pro. When I execute nand-sata-install script it looks like it works. It asks me to reboot but then issuing a df -h or mount does not show that I have a 32gb drive mounted on /. Is there something else I have to do after I run this script? Thanks! ril3y

Hi, how can I edit the ssh welcome message in my cubox? Thanks.

Hello could someone point me in the direction of the stretch images if they are still hosted here of course. I want to run omv and i just found out what is happening with omv5 and armbian the past year. So ill go stretch and omv4. Kind regards Oliver

Hi Igor, my Cubox-i4Pro worked perfectly fine with your Armbian Debian Jessie, until I upgraded from 4.7 to 4.81. After the upgrade was performed today, the system time is always wrong after boot, it is always set to Jan 1 01:00:00 1970. Setting the system time correctly does not help, after reboot it is wrong again. I didn't observe this behavior before upgrade, the system time just used to work without any attention needed. Nothing else was changed in the system, only the upgrade of Armbian was done to ver 4.81. So I'm wondering what went wrong with the upgrade. Hardware time is always correct, syncing system time to hardware time does not survive boot. I tried …

Not sure if this should go in this section, but since my problem is about non-supported board, then I guess... I found out about Armbian only recently and decided to give it a try for my T113-S3 based board I bought on Aliexpress. It looks like it's some kind of a MangoPi MQ clone, at least judging by schematics. I managed to create a new configuration for my board, together with required U-Boot patches. I built two images, for "current" and "edge" kernel. For some time I was under impression that Linux doesn't boot at all (serial console output was stuck at "Starting kernel ..."), until I added earlycon=on to armbianEnv.txt. Then I finally saw some outpu…

A couple years back a company named TBS, mostly known for their DTV hardware, released a mini PC styled thing. It's called the TBS2910 Matrix and was marketed mostly as a Kodi box. Sadly it doesn't seem the product made the sales necessary to keep the company interested - which in my view is a shame since it's got some interesting hardware features: Quad-core i.MX6 CPU (1GHz) 2GB DDR3 Ram MiniPCIe slot 16GB eMMC Storage SATA connector with 12V power, capable of powering a 3.5" HDD On-board 2.4GHz Wifi Gigabit ethernet (likely limited to 400Mbps or so) 3 USB 2.0 ports + 1 mini USB otg port 1 full-size SD slot, 1 microSD slot HDMI, analog and optical audio out I…

Hello. I've tried to find the TC358743 toshiba chip drivers in the kernel, but I can't. As far as I know they are included from 4.1 version, but in the menuconfig option I didn't found them. Is driver avaliable on this kernel or I should use another kernel?

I cloned the quite latest version of Armbian: commit 369e69a55390f59c2299c98c09bf3d805ac59335 (HEAD -> main, origin/main, origin/HEAD) Author: Ricardo Pardini <ricardo@pardini.net> Date: Mon Apr 3 13:15:54 2023 +0200 artifact-armbian-bsp-cli: hash more variables included in `/etc/armbian-release` Using the edge branch to compile for my renegade board, which has the rk3328 chip: ./compile.sh BOARD=renegade BRANCH=edge RELEASE=bullseye BUILD_MINIMAL=no BUILD_DESKTOP=no KERNEL_CONFIGURE=no COMPRESS_OUTPUTIMAGE=sha,img It blocks when start to boot the kernel: U-Boot 2022.07-armbian (Apr 17 2023 - 23:29:15 +0800) Model: Firefly roc-rk332…

Hi guys. I wanna ditch archlinux because its continuos issues with Kodi and uwsgi. Does Debian for arm play good with Kodi? Is there any major issue besides the network speed? Thanks!

I have lots of HummingBoards 2 Edge with eMMC but now got a batch with the new SOM 1.5 and eMMC the original u-boot from next and stable branch (2013-10rc4) get stuck on SPL from time to time on the new SOMs so I'm trying the dev branch which has this new patch: https://github.com/armbian/build/blob/master/patch/u-boot/u-boot-cubox-next/U-Boot-mx6cuboxi-add-support-for-detecting-Revision-1.5-SoMs.patch Copying SPL and u-boot.img to eMMC and booting produce the following: U-Boot SPL 2018.03-armbian (Jun 07 2018 - 16:06:14 -0400) Trying to boot from MMC1 Card did not respond to voltage select! spl: mmc init failed with error: -95 SPL: fail…

Hello and first off thank you for the great resource of information and downloads. I am having problems booting up a fresh image on my cubox i 4 pro. The last time i installed an Armbian Image was in 2014 when i got this wonderful little machine and while trying upgrading my own cloud to next cloud i got a bad big block so i thought lets put a fresh image on and now its been 2 days of time outs. The Solidrun logo comes up and then i see that it can't find any images, well i have pictures so there it is. I used etcher to make the sd card. I used the official sd card formatter. New SD card is 32 GB transcend 10 speed. In my router the cub…

Hi, I've just created a SD-card with Armbian Bionic (mainline kernel 4.19.y) for a Hummingboard Gate. I noticed during boot that it says it uses U-boot version 2013.10-rc4. This seems quite old compared to the 2018 version that was on the Debian Stretch image from SolidRun. I've tried to search the internet to see what the impact of something like this is and wasn't able to find something that made sense to me (could be entirely my fault). I therefore have the question: Is the U-boot version intentional? (maybe it has some features that newer versions have dropped.)

Hi all, After years of running Armbian on my Cubox i4 without problems, I am suddenly in a situation that I don't understand. For some reason, I decided to reboot it, and now it doesn't work anymore. Using a micro-USB cable and my Macbook, I connected to the serial line to grab some logging: U-Boot SPL 2017.11-armbian (Jan 24 2018 - 22:39:16) Trying to boot from MMC1 U-Boot 2017.11-armbian (Jan 24 2018 - 22:39:16 +0100) CPU: Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz) CPU: Extended Commercial temperature grade (-20C to 105C) at 41C Reset cause: POR Board: MX6 Cubox-i DRAM: 2 GiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using def…

Just upgraded to the new Jessie image 4.4.1. Is there any concern with this bad CRC warning? Do I need to update the u-boot.img? If so, how. U-Boot SPL 2013.10-rc4 (Feb 03 2016 - 16:37:42) Boot Device: SD1 spl: error reading image u-boot.img, err - -1 Load image from RAW... U-Boot 2013.10-rc4 (Feb 03 2016 - 16:37:42) CPU: Freescale i.MX6Q rev1.5 at 792 MHz Reset cause: POR Board: MX6-CuBox-i DRAM: 2 GiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: FEC [PRIME] Hit any key to stop autoboot: 0 mmc0 is current device ** File not found /boot.scr ** ** File not found /uEnv.txt ** ** File not …

hey, is there anyone who successfully compile armbian kernel with can support for uddo quad board ? (i also preffer compiled iptables module) here is my working patch with yocto project version dora http://pastebin.com/BF2SeWHa

I've loaded Armbian onto my Udoo Dual and am having issues getting it past starting the kernel. I really like this OS on my other sbc's and have had no issues before this. I'm mostly a Linux noob with an elementary grasp of compiling the kernel. I have had this problem for about a week and am finally asking the pro's on how to fix this. Any help would GREATLY appreciated. Below is what I get from the U-Boot startup. Thanks! U-Boot SPL 2015.10-armbian (Jun 13 2017 - 15:51:16) U-Boot 2015.10-armbian (Jun 13 2017 - 15:51:16 +0200) CPU: Freescale i.MX6DL rev1.1 at 792 MHz Reset cause: POR Board: UDOO DualLite DRAM: 1 GiB MMC: FSL_SDHC: 0 *** Warning - bad CRC,…

Hey All - So I decided to upgrade my Udoo from 4.5 (Debian Jessia, kernel 3.14.28) to the latest 5.25 Xenial. I gave next (4.4.46) a try, and it seemed to work awesome, however it seems like no one wants 1wire (still - it only takes up 1 gpio!). I built custom kernels enabling 1wire in the kernel and updated (or for default adding) 1wire to be enabiled in the imx6qdl-udoo.dtsi, however after I install the kernels, it just sits indefinitely at the red Armbian logo on boot. On 4.4.46, i was able to just install all the debs via dpkg -i *.deb On 3.14.56, I had to use dpkg --force-all -i *.deb Any ideas on what I'm doing wrong? Its been a while, so I'm s…

Hello, I deployed the latest image "Armbian Buster mainline based kernel 5.8.y" and after initial setup, I cannot activate the analog sound card. What I did: The "Hardware" section in "Settings" section of armbian-config was missing, so I installed the following packages: "linux-dtb-current-sunxi/buster 20.11.0-trunk.28 armhf Linux DTB, version 5.9.5-sunxi, linux-dtb-dev-sunxi/buster 20.11.0-trunk.28 armhf Linux DTB, version 5.10.0-rc2-sunxi" and after that changed: /boot/armbianEnv.txt by adding overlay_prefix: "sun8i-h3". This was the only way I could make armbian-config to correctly display the "Hardware" device tree. I tried to put: i…

Its been a while since I built a UDOO image (need another kernel module), when I ran compile.sh, it pulled new source and told me to clone a new build directory. In the process of cloning, however with UDOO being EOS, is it still possible to build the legacy kernel/image with current sources?

Hi i have an udoo quad and i downloaded your os (ubuntu jessie desktop Kernel 4.0.8). At first congratulation for your work and big thanks to share it After the flash of the sd card (used win32diskimager because imagewriter don't work for me), i can started my card. Ethernet, wifi, browser ... works fine ! Now, that it didn't work is sata disk or usb disk. When i plug it on the card nothing appear. If i go to /media i saw nothing. Do you know how to resolve this ? Otherwise, i would like to compile Qt5.5 but i need the header for openGL librairie to do it. Is it possible to have it (i saw nothing on /usr/include) ? Last think, do you plan to make a try with the new …

Using Armbian_4.4_Udoo_Debian_jessie_3.14.28 - Wicd doesn't detect any networks (/etc/network/interfaces has wlan0 commented out). If i setup /etc/network/interfaces and edit /etc/hostapd.conf and /etc/init.d/hostapd, I can get the udoo to authenticate to my wireless network, but I can't ping/resolve/browse anything but google.com Using CLI images - I can't get my network card to auth at all. Any idea what happened - a few months ago wifi was working perfectly. Also - is there anyway to modify the startup job to raise network interfaces to have a time limit? Occasionally boot will go indefinitely.

I migrated my system from Wheezy from udoo.org which installed long ago to Armbian Jessie. The main stuff is working and i also manged to boot the new kernel (u-boot config). When i do apt-get upgrade the system always want to upgrade the initrd file. I get the following error messages: update-initramfs: Generating /boot/initrd.img-4.4.51-udoo Warning: root device rootfs does not exist Press Ctrl-C to abort build, or Enter to continue Warning: /sbin/fsck.rootfs doesn't exist, can't install to initramfs, ignoring. update-initramfs: Converting to u-boot format Unsupported platform. run-parts: /etc/initramfs/post-update.d//flash-kernel exited with return code…

I was trying to install the udoo kernel but got stuck with this error: root@udoo:/tmp/4.0.8# ls -la total 32968 drwxr-xr-x 2 root root 4096 Jul 29 14:21 . drwxrwxrwx 5 root root 4096 Jul 29 14:21 .. -rw-r--r-- 1 root root 16875520 Jul 13 11:30 4.0.8-udoo-next.tar -rw-r--r-- 1 root root 11204 Jul 13 11:30 linux-dtb-4.0.8-udoo_1.8_armhf.db -rw-r--r-- 1 root root 49792 Jul 13 11:30 linux-firmware-image-4.0.8-udoo_b -rw-r--r-- 1 root root 6844194 Jul 13 11:30 linux-headers-4.0.8-udoo_1.8_armb -rw-r--r-- 1 root root 9096354 Jul 13 11:30 linux-image-4.0.8-udoo_1.8_armhfb -rw-r--r-- 1 root root 769836 Jul 13 11:30 linux-libc-dev_1.8_armhf.deb -rw…

got this message during build (during installation of additional packages: bridge-utils): [ error ] Installation failed initctl: Unable to connect to Upstart: Failed to connect to socket /com/ubuntu/upstart: Connection refused invoke-rc.d: unknown initscript, /etc/init.d/systemd-logind not found. dpkg: error processing package libpam-systemd:armhf (--configure): subprocess installed post-installation script returned error exit status 100 Processing triggers for libc-bin (2.19-0ubuntu6) ... Processing triggers for sgml-base (1.26+nmu4ubuntu1) ... Processing triggers for ureadahead (0.100.0-16) ... Errors were encountered while processing: libpam-systemd:armhf E: Sub-…

I am trying to compile the full OS image (incl. kernel and u-boot) for nanopifire3 target but fail every time. I am following the provided build instructions. I have tried compiling on multiple machines, but the one I am using has 8 cores and 12gb RAM. I have tried in an Ubuntu 22.04 LXC container, Ubuntu 22.04 in a VM, and the the docker container provided by Armbian. My kernel has the binfmt_misc module loaded (verified with lsmod), no spaces are present in build path, and I have tried both root user and sudo as a regular user. I have also checked the similar issues on the armbian forum Please forgive me if anything is incorrectly formatted or so, I have…

Hi there, on my Cubox i4 pro there was an update from 4.9.7-cubox to 4.9.12-cubox. It took quite a while, and there were a couple of messages: dpkg: warning: unable to delete old directory '/usr/src/linux-headers-4.9.7-cubox/scripts/genksyms': Directory not empty dpkg: warning: unable to delete old directory '/usr/src/linux-headers-4.9.7-cubox/scripts/mod': Directory not empty dpkg: warning: unable to delete old directory '/usr/src/linux-headers-4.9.7-cubox/scripts/kconfig': Directory not empty dpkg: warning: unable to delete old directory '/usr/src/linux-headers-4.9.7-cubox/scripts/basic': Directory not empty dpkg: warning: unable to delete old directory '/usr/src/…

On my Cubox, can I upgrade Armbian Bionic to Cosmic? Is that going to work? I'm not using any GUI / HDMI stuff, so that is not relevant for me Reason of my question: I want OpenSSL 1.1.1 (with TLS1.3), which is a part of Cosmic (and not of Bionic).

Upgrading cubox-i Armbian Buster from kernel 5.7.x to Kernel 5.8.y breaks ethernet and I'm unable to get it connected again. Works fine again downgrading back to 5.7.y. This occurs on multiple cubox-i devices. System diagnosis information will now be uploaded to http://ix.io/2zH6 dmesg | grep eth0 [ 4.667327] fec 2188000.ethernet eth0: registered PHC device 0 [ 22.369472] fec 2188000.ethernet eth0: Unable to connect to phy nlcli wlan0: connected to sketch-wlan "Broadcom BCM4330" wifi (brcmfmac), 6C:AD:F8:1D:36:25, hw, mtu 1500 ip4 default inet4 10.1.0.41/22 route4 0.0.0.0/0 …

UDOO Quad Hello. Armbian bionic desktop mainline based kernel 5.4, USB ports do not work, wifi module is not visible. Everything works correctly on Stretch. Do not tell me where to look for the reason?

I would like to run a vanilla/mainline debian kernel on my cubox-i4pro but apparently there is no image available for download. Is that be because the vanilla kernel is not supported or nobody has yet build one?

Hi every one, Im new on this form and this is my first time, when Im working with HummingBoard. On my HummingBoard is connected a little board with HDMI input and is connected with DVD Player. One another HDMI, which is on HummingBoard, is connected with Monitor, where I can see my console. So, my question is, how can I install, that my little board will become a video from DVD Player and streaming it to the HummingBoard, so, that I can see this video on my Monitor. Im using the Debian wheezy image Sorry for my english, hope for fast help

See the following steps to get the TI wl18xx drivers to work on the Cubox with the I4P Rev 1.5 SOM. Step 1) Boot with the Armbian base image (Armbian_5.20_Cubox-i_Ubuntu_xenial_4.7.3). The 3.14.79 base image also works however will require a different dpkg install command to overwrite the 3.14.79 kernel. Step 2) Build a new kernel with Armbian build tools, note this only works with the 'DEV' kernel branch because SolidRun provides all the necessary DTS files. Edit the compile.sh script and change KERNEL_CONFIGURE="yes" to customize the kernel configuration. The relevant modules you will need to select are: CONFIG_WL_TI=y CO…

Hi all, This is my first post! My cubox-i4x4 won’t boot with a second usb device plugged in. I am running the latest version of Armbian Jessie (Vanilla Kernel). I have done “nand-sata-install†booting rootfs from usb flash memory. Someone having a clue?

Hi, I installed xrdp with armbian-config. Now I'm able to login with rdp client, but I'm directed to an empty desktop. No bars/menue or similar, just empty no chance of doing something useful. What's wrong? Best wishes Paul

Hello (sorry, I am writing through a translator) I have a Zyxel NAS326 with a physically damaged NAND - it does not save the device configuration. board photo: Because I do not have access to the programmer, I want to replace NAND and program it in the NAS. However, I can not run U-Boot via UART. I tried the adapters on PL2303HX and FTDI FT232RL. I'm using a kwboot on this topic: and the u-boot file from this: https://forum.doozan.com/read.php?2,27108,31893#msg-31893 Every time this error pops up: root@gutek3:/gutek/nas326# ./kwboot-x86_64 -f -t -B 115200 /dev/ttyUSB0 -b uboot.bin -s 0 -q 1 Sending boot message. Please reboot the …