Amlogic CPU Boxes

I purchased this fake clone TV box of the classic Tanix TX3 Mini 2GB Ram 16GB Rom for around 20 dollars (including shipping). I discovered that the soc is S905L2-B and before bricking the card with attempts to install it on eMMC I wanted to know if anyone of you found a firmware for this TV box compatible with the Amlogic USB Burning tool. On the internet I only found two tx boxes that mount the S905L2 soc and they are the X7 5G and ipbs9505 and I couldn't find firmware to try to load them on my tv box, it's difficult on the Chinese forums for me to be able to find the downloads. Any advice is welcome because with boot from the SD and the armbian-d…

I'm trying to follow the SteeMan's Installation Instructions for TV Boxes with Amlogic CPUs. I'm want to install Armbian_23.11.1_Aml-s9xx-box_bookworm_current_6.1.63_cinnamon_desktop on a Tanix TX3 with a S905X3. Looking at other posts I think I got extlinux.conf correct but I can't find any ext files and I don't where exactly they are supposed to be. The boot folder in root is empty and there's not boot folder in the boot partition. No idea what tag is relevant so I choose one at random.

While clearing out a load of old computer bits I found an old Keedox M8N android TV box I had years ago. Before I dump it, is it usable for anything now? Can I install Linux on it for example?

I've been trying to install linux on a S912 chip, there are tons of tutorials on how to do it but when I check for the img file it is not there I've been referring to this forum p.s I know this has been outdated for a loooong time

Anyone have Armbian image for Amlogic S805? Android Box Infomation FDT: m8b_m201_1GB UART Log: QA5:B;SVN:B72;POC:1DF;STS:0;BOOT:0;INIT:0;READ:0; U-boot-00000-ge0c1103-dirty(m8b_m201_v1@) (Feb 02 2018 - 15:47:12) clr h-ram DRAM: 1 GiB relocation Offset is: 2fec4000 aml_card_type=0x200 MMC: [mmc_register] add mmc dev_num=0, port=1, if_type=6 [mmc_register] add mmc dev_num=1, port=2, if_type=6 SDIO Port B: 0, SDIO Port C: 1 power init out reg=c110804c,value=dfffffff IR init done! register usb cfg[0][1] = 3ff67d4c register usb cfg[2][0] = 3ff6ac98 NAND: EMMC BOOT: not init nand do not init nand : cause boot_device_flag without nand get_boot_devi…

After having seen the continuous hardware changes made by the manufacturers of the cheap Android TX boxes, I would like to understand if it is possible to recover the firmware, therefore the factory Android image compatible with the Amlogic USB Burning tool. After booting from the SD with the armbian-ddbr command, I managed to create a compressed file with the factory Android image but this file does not work with the Amlogic burning tool but only with the armbian-ddbr (restore) command. Since it is easy to brick these TV boxes by trying to install Armbian on emmc I would like to be ready to be able to load the original factory Android …

Hello, beloved community members! I hope you're all doing well. I haven't looked at my A95X F3 Air for quite some time, and I've got a few questions about the TV box. I'm interested in installing Armbian on it and I'm wondering which version of Armbian and Linux kernel would be most suitable. Last time I attempted this, there were issues with the RTL8821CU driver, specifically for an older Android Linux kernel, around version 4.9. I've come across this URL (https://github.com/ophub/amlogic-s9xxx-armbian/issues/269), suggesting more recent kernel versions now support the wifi chip. Can anyone confirm this, or recommend a version where there are no longer issues? …

Hi everyone! I want to know what is this marked pads? Blue -> Red -> Yellow -> Green -> Thanks a lot...

Hi, I have finally installed armbian in my amlogic. I want to make a backup of the emmc now that it is "just installed". So if next year or whatever, if i want to go to my first day after the installation, I could go quickly. What will be the best way to create a "rescure image usb" ? In case of a disaster, could I boot from usb or only from sd? Thanks

Long story short -- I was dumb and attempted to install armbian to the emmc on my s905 box because reading is hard. So now I have a box that won't boot. I have the original firmware image, which will restore the boot partition (from what I understand, this is the problem with s905s now, though I distinctly remember running debian on this via the emmc in the past, but that's a tangent that doesn't matter if I can't get it to boot anything). I have it connected via usb/ttl uart and can send commands. But what commands do I send? The amlogic usb burning tool doesn't see this box via usb, but if I run `usb start` it finds one usb device (presumably my …

Did anyone know how can I see if my TX3 has NAND or EMMC? I not sure if this is right but I'm facing some issues when trying to install armbian in my TX3, I burned and image with balenaEtcher in my sdcard but always says kernel panic or mainline 'bootfromsd is not defined' when booting armbian. It could be because of mem type?

HI, I have another post about Mini MXIII-II (if you have it, please start reading this post: My next step, as @SteeMan said me in that post, is to check "all" things in the SD card before installing armbian to the emmc. I have detected problems with audio and bluetooth. HDMI, WIFI, USB, LAN seems to work. If you will check anything more, please, tell me, thanks. My question is about... I think that hardware is defined in the DTB file, so ... could I check one by one "all" dtb files? (I mean only ones that have S905X in their names). does it make sense? Any other DTB file that I could test? Thanks.

Hello all! This is my story: I have a TV box with S905X Cpu and I would like to install linux on it. I tried to install Armbian via a usb pen and it worked but it was too slow, then I tried to install it on emmc with the command ./install-aml.sh but failed. Then i tried to use Armbian config and i bricked the tv box 😁 After some search, I found some tutorial to resuscitate it with USB Burning Tool, I shorted 2 pins on the chipset, installed an Aidan's ROM with Android 9 and worked well. But I want armbian, and now I don't know how to enter the device again in bootloader mode because when I turn on it boots up on AndroidTV without any other possibi…

Hi, I want to make step by step and I am reading all post that I can't, but I have not information about this. I can use linux commands, but I am a newbie. I have download and flash a micro sd as this links steps (I think there are the same what I have read in several posts here: https://i12bretro.github.io/tutorials/0269.html Firmware donwloaded from https://forum.armbian.com/topic/17106-installation-instructions-for-tv-boxes-with-amlogic-cpus (https://es.sbcmirror.org/dl/aml-s9xx-box/archive/) This one: Armbian_23.11.1_Aml-s9xx-box_bookworm_current_6.1.63_xfce_desktop.img.xz Checked SHA256 And flash Boot is ok with armbian. …

Hello, I'm trying to start ARMbian in my new TX3 mini (Amlogic S902w)...but I'm always having trouble in ARMbian boot. It always says Kernel Panic - not syncing: Asynchronous SError Interrupt. Following by a message that says CPU: (u-dev-worker) Not tainted 6.1.63-current-meson64. I tried an old images of ARMbian that I found in YouTube videos, but without success. The error changes the way that the message appears but its always this Kernel Panic in CPU.. I don't know if I'm doing something wrong, I'm trying so many DTB's with all these 3 u-boot.ext, but without success. I don't know if I should change the BOOT ARGS in extlinux.conf. There's so many doubts. Doe…

Hello I use TV Box model Vontar X3 it has amlogic 905x3 with 4g ram and 1gbit eth I installed armbian bullseye in emmc and it works fine. but I want recover my TV box to original firmware USB Burning tool(Ver 2.2.4) can't get TV box driver I use USB A to USB A cable, and use toothpick with reset button but USB burning tool not work My tvbox just boot with armbian. Please help

Hello Everyone, I'm an armbian user since 2020 and i'm having issues trying to run armbian on a custom TV box made from a company that sell iptv solutions for business. I've got this from one of the company manager as the device was failing HDMI and didn't want to bother themself with RMA, i've got few but really they trew out like 50 pcs. The device has a Amlogic s905x3 soc with 2gb Ram and 16gb memory. 1 usb 2.0 and 1 usb 3.0 otg, micro sd slot and many other component. wifi and bluetooth board and it's PoE. I know that S905X3 isn't supported very much but i've seen some posts from users succeding, so why don't try to let armbian run? …

I had a working setup with a small driver issue so I flashed coreelc on an sd card and after booting into it once, I can't seem to be able to boot into armbian anymore. booting into coreelec still works but the armbian sd stopped working. I tried editing the extlinux and evreything I soldered serial pins to see what's going on bl31 reboot reason: 0xd bl31 reboot reason: 0x3 system cmd 1. SM1:BL:511f6b:81ca2f;FEAT:A0F83180:20282000;POC:F;RCY:0;EMMC:0;READ:0;0.0;CHK:0; bl2_stage_init 0x01 bl2_stage_init 0x81 hw id: 0x0001 - pwm id 0x00 bl2_stage_init 0xc0 bl2_stage_init 0x02 L0:00000000 L1:00000703 L2:00008067 L3:15000020 S1:00000000 B2:20282000 B1:a0f8…

I have an old MXQ Pro S905 box I wanted to install Armbian on. I'd done this in the past, then I had coreelec on it, then decided to go back... But that's irrelevant. I got the image Armbian_23.11.1_Aml-s9xx-box_bookworm_current_6.1.63.img.xz from https://armbian.lv.auroradev.org/dl/aml-s9xx-box/archive/ and went through the whole process of getting it ready to boot. I started up the box and went about some other stuff because I remember it taking some time on the first boot. When I came back there were a lot of messages on the screen so I pressed Enter to see where the cursor was. It showed me a prompt, I typed `ls` to make sure things were …

Since some upgrades ago, the wlan0 stopped showing. Maybe it got jealous of the usb wifi dongle. They used to play along as wlan0 and wlan1 but that is no more. https://paste.armbian.com/zokubeduxe

My next step is to build a secure privacy oriented travel router with pi-hole, vpn and openWRT What is the recommend virtual server software for openWRT? docker or pimox? Is there any tutorial here on this community on how to install openWRT on armbian tvboxes, since I wasn't able to find anything, but some users claim they have successfully installed openWRT on their armbian tvbox. There's a tutorial on how to install pi-hole on this community and there's is also an unoffical armbian fork on github that offers out-of-the-box openWRT installation that might even work, but that is not an option for me, since they just stole the armbian name (ac…

Hello !! I ordered a box tv H96 MAX X3 With this configuration : -CPU: Amlogic S905X3 quad core BRAS Cortex A55; -GPU: ARM Mali-G31 MP2; - OS: Android 10.0; -Memory: DDR3 4GB, eMMC 32/64GB/128GB -Support: H.265, 8K @ 24fps, 4K @ 60fps, HD 2.1, USB3.0; -Support 10/100M/1000M Ethernet, 2.4 and 5G dual Wifi,BT4.0; I'd like to install Armbian on it to use it as a mini server. Except that I'm a complete idiot when it comes to computers, and I've tried to follow tutorials I've already seen, but I can't get the hang of it. I can't really find the right image and I don't really understand how to do it. When I try on my own and plug …

Hi, can you somebody tell me how to get the WIFI working on my box? build: Armbian_23.11.1_Aml-s9xx-box_jammy_current_6.1.63_xfce_desktop.img.xz boxname: Mecool KIII Pro SoC: s912 Ram: 3GB I have also tried with WL-167g USB WLAN adapter but without proper driver no succes. I am also not able to install driver ralink because of conflicts and possible dependencie issues. I also have no ethernet since I am using Huawei WIFI LTE Dongle Modem for all my devices and I have no ethernet adapter to plug it into my box. So I have 2 options, either use built-in WIFI chip or WL-167g USB WLAN adapter. I have trie…

I have an OTT TV Box, model ABOX-A1 ( 1G + 8G, S905X ). Inside it looks very similar to NEXBOX A95X. When it starts up while connected to a Protron PLTV-26 TV, the TV EDID gets changed. This happens both with the original Android and when booting Armbian. I don't think it's due to Armbian. I wonder if it is due to startup code on eMMC or SOC ROM. The changes happen at every startup and are always the same. It writes a 1 at EEPROM offset 2, and a 0 at offset 0x20. Normally, the EDID EEPROM chip is at I2C address 0x50, and many devices write protect it. On this TV it responds to addresses from 0x50 to 0x57 according to i2cdetect, and it is not write protected. T…

I have an OTT TV Box, model ABOX-A1 ( 1G + 8G, S905X ). Inside it looks very similar to NEXBOX A95X discussed at https://www.savagemessiahzine.com/forum/index.php?showtopic=770346 . It has an analog AV port, with a 3PEAK TPF632A audio line driver on the output. So, all the digital audio stuff is inside the S905X SOC, and maybe some GPIO switches mute of that analog output chip. I first booted Devmfc_Debian-Bookworm_6.1.57-meson64_Minimal-23.10.12.img.xz from https://github.com/devmfc/debian-on-amlogic and had sound on the analog output. (The later Devmfc_Debian-Bookworm_6.6.1-meson64_Minimal-23.11.09.img.xz did not work.) I used its aml-multiboot-setup.sh scri…

Is possible to make Armbian to work on the FlowBox F1 from Telecom Argentina (SkyworthDigital HP20A)? I attach a photo of the device

Hello, I would be grateful for some assistance on a sound issue. I installed Armbian_20.10_Arm-64_bullseye_current_5.9.0_desktop.img.xz on a YUNDOO Y6 TV Box with S905X. It worked fine, but I believe that there is no support for Armbian 20 anymore. Useful info, the sound was OK and the audio card was identified as GXL-S905X-P212. Then, I tried various versions of Armbian_23.11.1_Aml-s9xx-box_bookworm_current_6.1.63 and Armbian_23.11.1_Aml-s9xx-box_jammy_current_6.1.63. Most of them do work, but none detects the sound card. Now I am playing with Armbian_23.11.1_Aml-s9xx-box_bookworm_current_6.1.63_xfce_desktop.img, which actually has meson-gxl-s905x-p212.dtb in b…

I install Armbian on my K1 plus via SD card, I have already solved many problems, but now this one popped up. I couldn’t find any information on the Internet, I’m using the file meson-gxbb-p200.dtb, I really hope for your help!

I found a .dts file for my TV set-top box on an amlogic processor, and I want to compile this file for Armbian, please tell me how to do this, my TV box is K1 plus. https://github.com/CoreELEC/device-trees-amlogic/tree/master

Recently I've installed armbian on my 905 TV box using this article as a guide: https://i12bretro.github.io/tutorials/0269.html After some experiments with dtb files and tuning everything seems to work fine except of one thing: the box can't be turned off, it boots immediately after shutting down. I've found a similar problem described in several articles, for example: https://gist.github.com/george-hawkins/a897a6fe116093a4c1f29ad19df088de It is suggested to enable XHCI HCD quirks in grub. But there is not such file in the system I've installed, the closest thing I found was config-5.9.0-arm-64 file. What is the right way to modify it to add XHCI HCD qui…

Hello, i have a tv box H96 Pro+ with 3Gb ram and S912 processor. I used instructions from here, used balenaEtcher to copy data to SD card I adjusted the /boot/extlinux/extlinux.conf file and copied the 912 uboot to u-boot.ext When i try to boot the SD card, i am getting an error Failed to mount /dev/mmcblk1p1 as root file system. Full error in the attched image. What is confusing me is that it looks like the system is expecting /dev/mmcblk1p1 to be ext4 but when i check it in Gparted, it is FAT32 Would you please push me to the right direction? Thank you

Hi, i booted for the sd card, with armbian, and then i went do terminal and armbian-install, it went well, i formated the eMMC, and then after all i shoutdown, now i can't get it to turn back on, i don't have the remote, is there any pins to sort or any possibility to solder a power button ? tnks.

Hello everyone, I have a Tigre 2 TV BOX with Amlogic S905X, 1GB DDR3, and 16GB NAND storage. I'm interested in installing Armbian on this device, but there doesn't seem to be native support for the latest Armbian versions for NAND storage. I'm wondering if there is any way to install Armbian on this box, and if so, where I can find an Armbian version with a graphical interface and a Legacy Kernel 3.4.x that is compatible with Amlogic processors. I appreciate any help in this regard. Thank you in advance.

Hello everyone, I recently acquired a Tigre 2 TV Box with the following hardware specifications: Amlogic S905X processor, 2GB of RAM, and 16GB NAND storage (SkHynix). I attempted to install the Armbian operating system, and the installation process started from a USB drive. Unfortunately, after the installation, the device seems to be bricked as it doesn't boot up (led red). I've read that it might be possible to recover a bricked device by putting it into MaskROM mode through a process involving a short circuit. However, I'm not entirely sure how to do this, and I'm hoping someone here can provide guidance or steps on how to put my Tigre 2 TV Box …

H96 Pro Plus android TV box stuck at 2%, Tried to re install many, but stuck on 2%, any clue from fellows.,.,regards H96 Pro Plus CZ-S32-V3 (DDR4) 2016-12-15(A15)

Hi, I am a owner of the Amlogic S905X3 with 100MB (Not 1GB) Ethernet card (using with meson-sm1-sei610.dtb). It works but VFD screen doesn't work. What can I do? Thanks Best regards, Wojciech

hello everyone i have an dreamstar a5 (S905X3) i tried using x2 uboot it tries to reset but fails never got it to boot into armbian grabbed dtb from coreelec it freezes at black screen so i think the display drivers dont work (attached dtb file) my configs attached below aswell Website for the files specs etc : https://dreamstar.com.tr/UrunDetay.aspx?KatID=3&UrunID=47 im using old version of armbian 20.10 due to only working with update method (couldent make it work on the new version) sm1_s905x3_2g_1gbit.dtb u-boot.ext boot.ini s905_autoscript extlinux.conf

Guys, I installed "Armbian_23.08.0_amlogic_s905x2_lunar_5.15.133_server_2023.10.02.img.gz" on SD card and entered into TESLA MediaTech X700 with soc s905x2 in it. It boots flawlessly, I have created user name etc ... I am trying to install xone driver. https://github.com/medusalix/xone When I hit the "sudo ./install.sh --release" command, I got warning that my gcc is different the one that was used for kernel compilation. I belive that is the issue of not compiling the code. Why is it different ? What can I do in order to match it ? Here are details of the commnad: Installing xone v0.3-2-gbbf0dcc... Sign comma…

Hello Guys. What Armbian version and image would you recommend? I have a TESLA MediaTech X700 Pro with soc s905x2 in it. I would like to use it to play movies via kodi and play retro games e.g. via RetroArch. Previously I used CoreELEC on an sd-card that is great for movies. Retro gaming only with wired Xbox One or Xbox Series controllers (xone driver for MS USB Xbox dongle did not work there). I would like to use my Xbox controllers wirelessly. Thank you for your advice.

Hi. I'm out of my depth here, but I noticed that one of the official Armbian builds with platinum support is for the Khadas VIM1S, which has a S905Y4 SOC with 2GB of RAM. This is a similar configuration to many cheap Android TV boxes. According to some sources I can find, the S905W2 is also in the same family as the S905Y4 (Amlogic NE S4). Both are also supported by Coreelec, although I understand that Coreelec DTB's can't be used with Armbian. What would be involved in porting Armbian from the VIM1S to S905Y4/S905W2 TV boxes? Is this likely to work, and where could I start? Thanks!

Dear All, First I would like to thanks all the contributors to armbian, What a great OS for our small SBC ! Context: I run succesfully latest Armbian on a X9T 4K TV Box (amlogic s912) from SD Card 2GB (following instructions here The Problem: I would like to run armbian from emmc (16GB on this box) for better reliability and performance. So, I run the install-aml.sh script, I had some error (no boot.ini ...), but the process seems to finish successfully Next Reboot: It's seems my boot partition is Not OK ... something missing ... For reference See bellow for reference the suc…

I have a HTV5 box with Amlogic S905. I have tried every combination trying to load from the SDCard. Just wondering if anyone else have success and can provide a guide to get it working. Thanks

Hi all. This is first installation of armbian, and I'm tryng to install armbian on a beelink gtking that use a S922 chip. I followed these steps: 1- flash Armbian_23.08.0_amlogic_s922x_lunar_6.1.54_server_2023.09.21.img.gz on my usb pendrive using BalenaEtcher 2- rename u-boot-gtking.bin to u-boot.ext on root folder 3- edit uEnv.txt as follow LINUX=/zImage INITRD=/uInitrd FDT=/dtb/amlogic/meson-g12b-gtking.dtb APPEND root=LABEL=ROOTFS rootflags=data=writeback rw console=ttyAML0,115200n8 console=tty0 no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 I try to reboot with toothpick. The android b…

Hi, please help me install Armbian. Hardware: I have an X96 TV box with 2GB of memory and 16GB of storage. Software: I'm trying to install Armbian_23.08.0_amlogic_s905x-t95_lunar_5.15.132_server_2023.09.21. I downloaded the image, wrote it to the SD card and successfully booted using the toothpick method. Booting from the SD card is successful, everything works fine. When I try to install Armbian on emmc the installation just stops. If you cancel the installation (ctrl + c), the system continues to work normally. I also tried using the image Armbian_23.08.0_amlogic_s905x-t95_lunar_6.1.52_server_2023.09.12. To install, I use…

After trying the 6.1.11 version of the system (XFCE Edition), I could get the system to start, but the loading proccess get stuck on "random : crng init done". I've been waiting for about 20 minutes now and the proccess stay on like the attached image. Downloaded file: Armbian_23.02.2_Aml-s9xx-box_bullseye_current_6.1.11_xfce_desktop.img.xz

Does anyone know what is the real specs of this board. I try to boot armbian in pendrive into it but it always boot to the android system or in recovery. I try the different device tree but it always the same result.

Hello everyone, how are you? I would like to raise my problem, which is installing the Batocera 35-34-32 system on the x96max+ device..s905x3. After installation, the Wi-Fi does not work. I tried many dtb files and they did not work. I tried on 3 devices with the same type, but it did not work. How do I solve this problem? Thank you

I have and android Box with model#ZXV10 B760HS3 its bricked due to wrong firmware i am to go to maskrom mode but unable to flash any file while flashing when i enter update bulkcmd "setenv -f EnableSelinux permissive" i receive "AmlUsbReadStatus retusb = 1 Usb status not success" can some Guide me how can i make this thing alive

Hi, I've X96 max+ and i want to install home assistant on it. i've reads lots of stuff about it but i don't know what image should i use and what to change in the config files. can anyone give me the exact install file that i need for my X96 that will work and i can install HA? THX

Hi Forum members, I have a Beelink GT1 Ultimate tvbox (RTL8211f/LTM8830) which came to me with Coreelec, so not the stock Android firmware. I had to install the Android firmware (found somewhere on internet, not from Beelink) in order to be able to run Armbian (off sd card) and no matter which .dtb I try, there is no LAN in Armbian (no phy), but also it doesn't work in Android. Am I right in that I cannot make it work in Armbian if it doesn't work in Android? Case 1: Eth port/rtl8211f chip is damaged Case 2: the Android firmware image does not fit my tv box Is there a chance that case 2 is the situation so if I find an Android image with working LAN t…

I woud like to contiune "Armbian for Amlogic S805 and S802/S812" here. Any firmwares or tutorials are helpful.

Hi, So I trashed the eMMC on my Amlogic s805 based TV Box, with 1GB RAM and 2GB eMMC. Getting it into mask ROM mode is easy enough, but how to resurrect the eMMC, so that I can boot Armbian off an SD card, is a total mystery. Can it be done, and if so...how? Any advice, or direction to said, greatly appreciated. T.

Hello all, I'm new member on this forum and I want became new user of armbian to install Home Assistant on my box. My box is a Bqeel K12 but i opened box and I see a label on the mother board where is write Mini M8S pro C. So I try to install armbian debian. I used this version "Armbian_23.5.1_Uefi-arm64_bookworm_current_6.1.30_cinnamon_desktop.img" I followed this topic to find the good dbt file : https://forum.armbian.com/topic/17106-installation-instructions-for-tv-boxes-with-amlogic-cpus/ I found differents dbt files which look like working properly (I have the desktop, I can navigate, open application...) BUT at each time is not pos…

hi im trying to install armbian on a t95m s905x box but for some reason it dont want to boot i installed batocera in the past, could it be the problem here?

Hello . I am new to Linux I need to install armbian on x96 mini to run Klipper server for 3d printer on it. I tried many builds but native WIFI doesn't work anywhere. Also, usb wifi does not work on RTL8188FTV. I tried to install the driver from the links https://forum.armbian.com/topic/12160-x96-s905x-driver-rtl8189es-and-rtl8188ftv-for-octoprint-and-klipper-3d-printer/ but can't find a working install kernel headers. Can someone help me choose and install any assembly for the s905w processor on which either native wifi or RTL8188FTV will work. Please help a newbie.

Hi, I am running Armbian on x96 mini with S905W chip. There are four K4B2G0446D chips which from data sheet is 512MB each. The only DTB's files that work for me are `meson-gxl-s905w-p281.dtb` and `meson-gxl-s905w-tx3-mini.dtb`. Is there a way to validated for sure if I have 2GB of RAM? Is there other dtb files for the 2GB variant?

如题，我是中国人，我来自中国广东。由于我免费使用了社区网友的armbian系统，我想对此表示感谢。我手里有几个几乎全新的TX3-MINI电视盒子，捐赠给固件开发者或者有需要的人，但是我不知道你们的地址在哪里，而且我想我恐怕也付不起高昂的国际运费，我并没有国际邮寄这方面的经验，我想如果我想免费捐赠3个电视盒子给社区朋友们，但是又可以不出邮费，请问是否可以做到？我应该选择哪家快递呢？ As the title, I am Chinese and I am from Guangdong, China. Since I used the armbian system of the community friends for free, I would like to express my gratitude. I have several almost new TX3-MINI TV boxes in my hand, donating them to firmware developers or people in need, but I don’t know where your address is, and I don’t think I can afford the high international shipping fee. I don’t have experience in international mailing. I think if I want to donate 3 TV boxes to communi…

Hi. I cant boot versions with 6.1.30 and 6.4.3 on s905x2 t95q . It boots in black screen. 6.1.11 working fine.

Hello, I have installed the armbian bookworm version with xfce on it, 6.1.30 kernel on my 32gb usb flash drive using balena etcher according to the instruction, I have tweaked the boot.cmd file, and only tweaked the video settings and regenerated using the mkimage command, Using linux to setup. and when I tried booting on the tv, everything worked till bam it kernel panics and starts flashing the red status leds on my android box. The kernel panic error is not syncing asynchronous SError interrupt, I cannot get anymore logs because I dont have any loggers, There is an uart port on my tv's motherboard but i dont have an usb to ttl device. Keep in mind, i cannot use sd…

The latest version Bookworm cannot start up when use udisk Perhaps the latest version of the kernel does not support USB drive startup。 The name of image is "Armbian_23.8.0-trunk.71_Aml-s9xx-box_bookworm_edge_6.4.2.img" The log is as follows： scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Found /extlinux/extlinux.conf Retrieving file: /extlinux/extlinux.conf reading /extlinux/extlinux.conf 522 bytes read in 28 ms (17.6 KiB/s) 1: Armbian Retrieving file: /uInitrd reading /uInitrd 22828930 bytes read in 679 ms (32.1 MiB/s) Retrieving file: /Image reading /I…

hello, I use this Image: Armbian_23.02.2_Aml-s9xx-box_bullseye_current_6.1.11.img..gz I can't find a way to autologin a user and execute a script. I need login because I need to see output of script in the screen. thanks in advance.

Hi team I was trying to install armbian image in S905L 3A-B device but its not booting and i am not able to kill the android on it so can anyone suggest me how can i proceed further with this device. Thanks

Hello! Can someone help me with installing Armbian on this tv box: eu.strong.tv/en/products/ip-tv-receivers/leap-s1 ? This does not have the recovery button in AV slot so i am accessing the android recovery boot through adb from my pc. But the "apply update from sd card" doesnt have any files. I can see the folder structure on the sd-card but i dont have any file to choose. I am using this build: Armbian_23.5.1_Aml-s9xx-box_bookworm_current_6.1.30.img. I also have chosen the correct u-boot.ext file. Thank you in advance!

Does This Brick My Tv Box?

Is there a path to upgrading the kernel? E.g. pull it from the up-to-date .img files or something? Thank you.

One question, how do i install kernel headers? I tried using armbian-config but it installed linux-headers-6.1.11-meson64 but the kernel is 6.1.30-meson64

I have the old image and it works on my box Armbian_23.02.0-trunk_Aml-s9xx-box_kinetic_edge_6.0.11_xfce_desktop. I try to put new image Armbian_23.8.0-trunk.53_Aml-s9xx-box_lunar_edge_6.2.16_xfce_desktop and it doesn't start it shows black screen. You know what I'm doing wrong ?

Hi, I am trying to install/boot latest Armbian Jammy minimal on Tanix TX3-H box without success. Technical Details: Box: Tanix TX3-H (BZ) CPU: S905X3 Memory: 4 GB Storage: 64 GB Box: https://androidpctv.com/review-tanix-tx3-s905x3-opinion/ Board Images: Attached I created bootable both usb and sdcard but the box boots into a dark blank screen. I followed the Amlogic boxes instructions but no luck. Tried the different DTBs from the Meson SM1 series, none booted up. Any guidance on using Armbian on this box will be very helpful and appreciated 🙏

Hello I newly installed a community armbian image to my Alfawise H96 ProPlus TV box. All seems to be working except sshd. I found out, that is because of not existing /run/sshd directory. After creating this directory the systemctl start ssh wokrs, but until the next reboot. The image I used is Armbian_23.8.0-trunk.51_Aml-s9xx-box_lunar_edge_6.2.16.img. Thanks

Hello everyone, I have a Beelink GS king X android box with 2 hard drives. I want to be able to install a jellyfin server to share and synchronize my videos, audios and images on my other devices. On these other devices, I will use either Kodi or Corelec for playback. Is it possible and reliable to install Armbian on Beelink GS King X to be able to install a Jellyfin server, but also a samba sharing server to share all my files? Or should I rather opt for another CoreElec or Manjaro type solution for example?

hello, I have mqxpro s905 tx box. armbian 23.05.0. I installed ffmpeg. If I try to play a video with ffplay I always get "segmentation fault" . I never tried any other sw that use graphic. Maybe I need to setup video? thanks in advance

Hi, so after many hours of trial and error I have managed to get the latest Armbian with Kernel 6.1.27 running on my old mxq s805 tv box. Albeit only thing that is not working is hdmi output and wifi. So for anyone else trying to accomplish something similar, my steps were: https://github.com/hzyitc/armbian-onecloud Downloaded the latest release of this build for the onecloud device as it also runs on the s805 amlogic chipset (props to the developer for still updating) Burn the image to your sd card. Then after the image is burned, create a textfile on the root of the sd card and name it „uEnv.txt“ …

Hello, I've a tv box marked MXQ PRO 4K quick play (S905 soc). toothpick recovery no longer works after installing not correct android rom Anyway I installed Armbian choosing random zip file in "update" app in android. Armbian works ok, but if I remove sd card android stays forewer in boot splash screen. Also I tried flash chip short, worked once, but now I can't repeat (is quite dangerous shortin random pins, no documentation for this board) Is it possible to trigger "reboot update" from armbian? Or to start recovery from Armbian. I have android IMG with dtg.img and recovery.img if needed- Thanks for help

Hi, I have an A95X F3 Air tv box that has an s905x3 chipset. I followed the instructions here. I believe i used the correct dtb file and tested out multiple others. I've tried reformatting my drive with SD card formatter. I've tried flashing my stock firmware. However I cannot seem to get armbian to boot. I'm getting no video output. I'm not sure what I'm doing wrong here. I've searched high and low on the internet and I could not find a solution. I have seen aml_autoscript.zip being mentioned here and there however the image I've downloaded doesn't seem to have it. Any help would be appreciated.

Hi. I can't boot my HK1 S905X3 1000m box 4GB 32GB. I've tried many dtbs, u-boots, and releases. I've attached a copy of the picture of the box I have. I've tried these releases, among others. https://github.com/ophub/amlogic-s9xxx-armbian/releases/download/Armbian_bullseye_lts_2023.05/Armbian_23.05.0_amlogic_s905x3_bullseye_5.15.110_server_2023.05.13.img.gz https://armbian.chi.auroradev.org/dl/aml-s9xx-box/archive/Armbian_23.02.2_Aml-s9xx-box_bullseye_current_6.1.11.img.xz I renamed u-boot-s905x2-s922 to u-boot.ext. I changed the DTB in extlinux.conf. I've tried fdt /dtb/amlogic/meson-sm1-hk1box-vontar-x3.dtb among many others. …

Hello ! I have a new x96 mini that comes with stock android 11. Model X96 Mini B00-M96-EMCP-REV1.4 Kernel 4..9 113 #87 SMP PREEMPT Thu Feb 9 20:08:30 CST 2023 Android 11.1 The design is different the usual u-boot and dtb don't work. I connected it by UART and I have this boot log and console mode. boot&env.zip Is it possible to find working u-boot and dtb?

Hello everybody, I need help because I screwed up when trying to install the system on emmc. The emmc is formatted and does not allow to initialize a boot sequence😢 A connection on JDEBUG1 shows that the box loops on this initialization sequence again and again. GXM:BL1:dc8b51:76f1a5;FEAT:ADFD718C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0; TE: 136356 BL2 Built : 14:17:47, Apr 18 2017. gxl g95dc662 - xiaobo.gu@droid05 set vdd cpu_a to 1120 mv set vdd cpu_b to 1050 mv set vddee to 1000 mv Board ID = 1 CPU clk: 1200MHz DQS-corr enabled DDR scramble enabled DDR3 chl: Rank0+1 @ 912MHz - PASS Rank0: 1024MB(auto)-2T-13 Rank1: 1024MB(auto)-2T-13 DataBus test pas…

Hi wifi work from SD card, after installing to emmc WIFI HW not recognized. Image from https://github.com/armbian/community bookworm edge minimal 222M 6.2.14 How to solve it? instal via armbian-config dtb: meson-gxl-s905x-p212.dtb IMG: Armbian_23.5.0-trunk.140_Aml-s9xx-box_bookworm_edge_6.2.14_minimal.img HW: mbox s905x v0.3 WIFI: RTL8723BS

Dear All, i new in armbian and want test it in device B860H . I have download and copy using balenaethcer / rufus to microsd . i need to change extlinux . > disable rk-3399 and enable aml s9xxx I try read microsd was format and install with rufus/balenaetcher with Microsoft Window 11 and Mac OS Montery, but can't detect partion or data inside microsd. any one here have manual to deploy armbian in BH860 with version bulleyes ? many thanks before and have a nice day

"A multi-port development board product designed based on the amlogic S905x3 platform, with the following specific configuration parameters: Processor: amlogic S905x3; RAM: 4GB; Storage: 32Gb (max 128GB); Number of network cards: 4*1GB (RGMII*1 RTL8211F + RTL8153B*3); Wi-Fi: 2.4G+5G+BT (AP6255); Expansion interfaces: TF-Card*1, HDMI*1, USB3.0*1, USB2.0*1, DC*1; Casing material: Metal; Casing dimensions: 133*108*27MM; Cooling: Two 5v fans provide heat dissipation; Accessories: 5v 3A power adapter*1 (220v to 5v), 9cm Wi-Fi antenna*1; Note: We are a software and hardware development team from China, and we hope to provide 1…

Hello @SteeMan, I install armbian on X96 Max Plus with S905x3 4Gb RAM and 64Gb ROM, thanks a lot for your work, the ethernet and emmc install is ok, but NO audio? I use meson-sm1-a95xf3-air.dtb and Armbian_23.02.2_Aml-s9xx-box_jammy_current_6.1.11_xfce_desktop.img What dtb file I must use or where I can learn how to compile new dtb file? Can I use emuelec dtb files? Regards

Hi to all, i've been reading this post but also others, tried multiple .dtb and multiple images (from balbes150 yandex) but all with the same result. Tried both with USB stick and SD card. From USB starts without pressing the reset button (behind AV), but for SC card needs to be pressed. My TV Box is a MXIII 4k, model M82, k200 board with 1Gb of RAM and 8Gb of ROM and, i believe, with a amlogic s802. I wanted to install ubuntu desktop in eMMC if possible.

Please, help me to boot armbian on MXQ PRO 4k (AM95AXQ v1.0) I try different dbd files, I can’t boot at all, I try to hold the reset button and turn on the power, but what, just a cyclic reboot of my device, I ask for help, what am I doing wrong?

I use the x96 air 2g_100m (s905x3) version. I used Armbian for amlogic(bulls_eye, xfce) boxes as specified in the tutorial here. I tried with many dtbs, (it even had one named x96 air) all of the didn't work. So I tried the u-boot.ext file from this Manjaro for Arm tutorial. (The link for the archive). This combined with 'meson-sm1-x96-air.dtb' file worked great and I was able to boot from SD card without any hiccups. And for the first time, the onboard wifi was working flawlessly. I could only get it to work with Coreelec before. With this, I decided to write it to emmc . I used the 'install-aml.sh' to do this and it completed successfully. But when I rebooted from em…

Hello all, After installing armbian, it was given the ip 192.168.1.16 by my router's dhcp. I changed the ip address using armbian-config to 192.168.1.88 Now it has 2 ip addresses and I can access both of them. How can I remove one from dhcp? Thank you

Hi all, I just managed to install Armbian to my Minix Neo U1 on sd card. I read the faq and found that installing on eMMC is better than on sd card because eMMC is faster and more durable. Now I'm curious that if I'm booting from eMMC: 1. How can I boot from sd card again? Just in case something's wrong with the eMMC etc. 2. Can I still use a blank sd card for storage? Or there shouldn't be an sd card attached because it will try to boot from sd card? Thank you

Hi, I tried to install Armbian in the recent days, but I wasnt unable because the image says "Map file error" or the update app will not read the Micro SD card (Armbian 23) I was wondering, where can I get this image of Armbian "Armbian_20.05.1_Arm-64_focal_current_5.6.2_desktop_20200408.img" ? It worked in a similar TV Box tutorial and I tought it could work in mine. Thanks for any help given This tutorial "http://www.galipe.net/guide-mecool-m8sproplus-armbian/"

Hi, I have a X96 mini box. I can install old version of armbian like Armbian_20.10_Arm-64_bullseye_current_5.9.0.img.xz but the newest versions are Uefi example Armbian_23.02.2_Uefi-arm64_bullseye_current_5.15.94.img.xz Can I install it ? Or there are no uefi versions ? Best regards

Proper way to install Armbian linux on H96 Pro Plus s912 or equivalent CLI ver. for those who have trouble in their existing systems. I have been installing/testing on my old dusty H96 pro plus Armbian Linux tested both flavours Debian and Ubuntu from almost all sources nothing works 100% on emmc except one source and installing method which i will mention below. Problem faced: Even correct SDcard burn with proper uncomment dtb for s912 and rename correct uboot as mentioned all over the forums: - installing on emmc problem, system halt on reboot/shutdown/power on/idle, Ethernet disconnection, no WiFi even with correct ath10…

Help me, please. Ineed install ARMBIAN on tv box Steren. I already tried, but I couldn't. https://photos.app.goo.gl/79cL29fdSD3sA4yLA

Hi, I have an oldish media center that I wanted to install linux on Mini M8S II 4K Smart TV Box Android Amlogic S905X (p212) I went to https://github.com/armbian/community#optimized and used Etcher to create this image Armbian_23.05.0-trunk-e33842ef2_Aml-s9xx-box_lunar_edge_6.2.9_xfce_desktop.img I followed this tutorial to get the boot process running commenting out the p212.dtb entry which seems to be the correct one for my board. It seemed to be going well, that is, the Armbian image booted the splash screen and I went through the various prompts to set the language, locale, timez…

Hi, I would like to know if its possible to boot from SD card in my model of Android TV BOX. It does not have a reset button but has an update app. Its a Giga TV Box HD890 4K. It has an Amlogic CPU I do all the process of installing Armbian in the SD card, Android starts an update and it says: "Map file is too short". I really dont know what I have to do to enable multi boot. Installation is aborted. Im getting really upset for not being able to install Armbian. Any help to this issue would be really welcome. Sorry for my bad english

I have a box S905X SOC I want to use the universal asynchronous transceiver device to debug other devices what should I do TtyAML0 is used by the Console as a debug universal asynchronous transceiver and cannot be used.

Hi! I'm new to armbian and just installed it on my KI PRO , AmLogic s905d . I've compiled my own version using the last build . Use the image to generic tvb for s905 with debian 11. to configure the boot I use the KII PRO dtb : /boot/extlinux/extlinux.conf The box is running very well , however I have two issue with it. One of them is with eth0 doesn't recognize the cable connected . I saw the answer here about @mrv issue and found no solution until now. I'm not sure where I can try any other module to test my ethernet card... Generated my armbianmonitor : https://paste.armbian…

Hi Guys, I am looking for latest Armbian image which works for Beelink GT1 Ultimate 3/32GB (S/N = G912) Amlogic S912 TV box. My requirement is only wired network to be working and that Armbian image must have kernel headers. The only old image that work is Armbian_5.37_S9xxx_Ubuntu_xenial_3.14.29_mate_20171226.img but missing kernel headers & not able to find kernel headers that matches kernel in the image. I tried Armbian_20.10_Arm-64_focal_current_5.9.0_desktop.img with 3 different dtb files as follows: dtb file: /dtb/amlogic/meson-gxm-q200.dtb dtb file: /dtb/amlogic/meson-gxm-gt1-ultimate.dtb dt…

Hello, I have an old TV Box model MX-III-4K with S802 CPU and I booted into Armbian from an USB stick. I found an older Armbian version (and dtb) that works on this box and I have network and everything, so I'm happy with it, except that I would like to add also NAND support. Anyone can advise me how can I do that? Basically I would like to be able to access its internal NAND, to read it/write into it. Armbian version is 5.77 user-built Debian GNU/Linux 9 (stretch) 3.10.108 Thanks

Hi all, My s905x TV box worked well with Armbian_23.02.0 (03.17.0615/Armbian_23.02.0_amlogic_s905x_bullseye_5.15.100_server_2023.03.17.img.gz). Today I tried Armbian_23.05.0 (03.19.0453/Armbian_23.05.0_amlogic_s905x_bullseye_5.15.100_server_2023.03.19.img.gz) Debian is stucked at first boot with network configuration. Same issue ethernet plugged or unplugged I cannot find anymore Armbian_23.02.0 prebuilt image Edit: Armbian_23.02.0 found in 03.19.0427 Many thanks!

I'm using, TV Box Name: X96 mini CPU (example: amlogic s905w): amlogic s905w Armbian build file name: Armbian_20.10_Arm-64_focal_current_5.9.0_desktop.img.xz DTB file used: meson-gxl-s905w-gxl-s905w-p281.dtb During the boot time stacked(freeze) the screen.

Guys, I need to build a cheap NAND reader/writer to clone few NAND chips, and I have some old android TV Boxes that I'm thinking to re-purpose for this job. It's a one time job so I don't want to buy a professional NAND programmer as they tend to be quite expensive. Do you guys think this would be possible? So, I'm thinking to boot from an sd-card or usb stick with Armbian and get access to the NAND chips that all my tv boxes have (I have some old MX-III and M8 boxes, model K200 I think, with S802 cpus and 8GB NAND). If I manage to get NAND access I can de-solder and solder other chips that I need to write from/to. Does anyone have any experience with this and ca…