Beginners

Hi team. I am having a difficult time getting the standard Opi CSI camera to work on the newest mainline Armbian. I don't have the ability to use a legacy version because it is coupled with a preconfigured Octopi, thanks to @ldiaz. He says that Octopi will work with the camera once the system works with the camera, and I have not been able to get it to work. There are at least a dozen threads here about that camera, but most are dated. And the ones that aren't seem to talk more about performance, and they assume that your camera is working. I also saw one about overlays, which I have no idea how to deal with, or even what they are. Something tells me it just isn't thi…

Hi, I'm using Orange Pi One board for Octoprint, but it's slow sometimes, because of max cpu frequency at 1 GHz. Under full load cpu temp is not higher than 30 °C, so I would like to set higher frequency, but all images looks like their max cpu frequency is just 1 GHz. So, is there any image with higher max cpu frequency? Thanks

https://packages.debian.org/sid/armhf/u-boot-sunxi/filelist Orange pi one is not on the list. Any solutions? Thank you.

I installed a LinuxCNC for my orange pi one, the mouse and keyboard will not work after restarting Here is the log http://ix.io/2AgR

Hello, I'm running Armbian on a Orange pi one. In htop I found out that the CPU temperature is not correct. So I tried to figure out what happens. The CPU is define not as hot as the value says. For me it looks line that the factor is about 2. I just wanted to inform about it. I can also deliver more information if required and also support to debug... I started the following commands for verification. $ cat /sys/devices/virtual/thermal/thermal_zone0/temp 63809 $ armbianmonitor -m Running unprivileged. CPU frequency will not be displayed. Stop monitoring using [ctr…

I have a orange pi one lying around. I need two usb ports. Is it possible to use the otg port as host port? (Need wifi and a webcam) The seach didn't give me an answer... If i post in a wrong section pls. move. Thanks Markus

Hi i'm interested in buying an orange pi , i'm interested in running linux and android and the use is for some gaming, using for facebook internet etc. Questions i like to have some help. 1 - Can i run games like gangstar vegas, gta San andres , the orange pi is good for this type of games on android or i have problems it temperature? And i know for this type of use the orange pi needs a coler. 2- I'm a beginer in linux it's easy to install and run some software that i can use for some works? 3 - In daily are much difference if i compare a orange pi and a android box? Thank you for all your help, and remember i'm beteween orange pi or a androi…

Hello, Now I got 3 different sata -> USB Brigdes but none of them are recognized by any of the USB Ports. I was just wondering which sata is build onto a orangepi 2 plus so that it works. Is it even connected internally via USB? Anything is helpful, since I would like to install mediavault and it does not really make sense. :-> all the best

by asking sudo iptable -l i get this

Hello, I get these errors when I try to "apt-get upgrade" Err:1 http://mirrors.xtom.de/armbian bullseye/main armhf linux-dtb-current-sunxi armhf 22.05.3 404 Not Found [IP: 2a09:0:8::14 80] E: Failed to fetch http://mirrors.xtom.de/armbian/pool/main/l/linux-5.15.48-sunxi/linux-dtb-current-sunxi_22.05.3_armhf.deb 404 Not Found [IP: 2a09:0:8::14 80] E: Unable to fetch some archives, maybe run apt-get update or try with --fix-missing? Is Orange Pi PC still supported by Armbian? Btw I'm using "Armbian 22.02.2 Bullseye" Thank you, Regards, dhr

i have a orange pi pc and i was trying to update kernel and i made a huge mistake, i installed linux-image-next-sunxi instead of linux-image-next-sun8i !!!! now my orange pi pc dont boot, can i reverse my error, how can i change boot in SD card to boot with sun8i ??? please help

I have a orange pi PC board that runs newest armbian 21.05 (kernel 5.10). I create a h264 video from v4l usb camera successfully with ffmpeg -f v4l2 -channel 0 -video_size 1280x720 -i /dev/video1 -pix_fmt nv12 -r 30 -b:v 64k -c:v libx264 test.mp4 but fps is low (10 - > 15 fps) and 100 % cpu load. When i used Cedrus264 encoder with: ffmpeg -f v4l2 -channel 0 -video_size 1280x720 -i /dev/video1 -pix_fmt nv12 -r 30 -b:v 64k -c:v cedrus264 test.mp4 ffmpeg failed: sudo ffmpeg-3.1.4 -f v4l2 -channel 0 -video_size 1280x720 -i /dev/video0 -pix_fmt nv12 -r 22 -qp 30 -c:v cedrus264 -c:a None night_video_test4_1920x1080.mp4 [sudo] password for lam…

Hello, I just bought Orange Pi PC lite and I have a problem with the version of Orange Pi on site is I think a Server Desktop and Doest have Gui Interface where can I Download the Graphical Interface, I think It is possible but I dont know where to get it , If someone Help me I aprricate it.

I would like to add new resolution with this patch: https://github.com/FireflyTeam/armbian-build/blob/master/patch/kernel/sun8i-default/0026-h3-hdmi-additional-mode-800x480p-from-lobodis-initia.patch But I need this parameter means: in drivers/video/sunxi/disp2/hdmi/aw/hdmi_bsp_sun8iw7.c vic dclk, int, mx, vst, my, mhbw, vfp, mhfp, +x, hbw, hfp, hst, +y, vbw, h v h_pol v_pol in drivers/video/sunxi/disp2/hdmi/aw/hdmi_core.c PCLK x, y, HT, HBP, HFP, HS, VT, VBP ,VFP , VS, h_pol, v_pol, int I know pclk: pixel clock x: 1024 y:600 …

I've got an orange pi pc plus camera board from aliexpress. But when I plug it into the orange pi and boot up armbian it doesn't work! It says on the cable: 2035-IPLAY. I tried with the built in android image but it also doesn't work! So I don't know what the problem is! Here is the aliexpress link to the camera board: https://www.aliexpress.com/item/4000310628213.html?spm=a2g0s.9042311.0.0.32f74c4dvVQry6

I picked up an OrangePi PC Plus. I installed armbian Jammy which does not have the mt7921u driver. I would like to install the driver and was wondering the proper steps. I have done apt install linux-headers-current-sunxi cd /usr/src/linux-headers-5.15.93-sunxi make scripts Now is it a matter of grabbing the mn7921u source and compiling it? Thanks for any direction.

Guys, how to setup HDMI display resolution please? This is strange, I waste whole day for seaching working solution

Hi, I'm a beginner for orange pi series, so I bought an orange pi pc+ and I tried to use load cell with HX711. I've searched all github links and common forums but I couldn't find anything about to reading HX711 by orange pi pc+ or any device using armbian os. If I need to explain in more detail, I've checked the HX711 libraries to use reading functions of gpios. Is there anybode help me. I want to use Orange Pi in my bachelor thesis because it is cheaper than Raspberry Pi so I really need help.

Out of the blue without any manual changes Orange PI PC Startup script screen stopped showing today. Is there anyone who knows how to fix that ? or what might have happened ? Thanks Björn

Hi there i was trying to set up orange pi pc + as a wifi acces point server. i got most every thing to work fine i can talk to all the intenal ip remotely just can not talk to internet from wifi side, from the board (eth0) itself no problem.. my configutation is installed -- hostapd and dsnmasq /etc/network/interface # Local loopback auto lo eth0 wlan0 iface lo inet loopback # Wired adapter #1 allow-hotplug eth0 #no-auto-down eth0 iface eth0 inet dhcp # hwaddress ether # if you want to set MAC manually # pre-up /sbin/ifconfig eth0 mtu 3838 # setting MTU for DHCP, static just: mtu 3838 # Wired adapter #2 #allow-hotplug eth1 #iface eth1 inet dhcp # hwaddress et…

Hello, I want to connect my orange pi PC+ on my cathode ray television over the jack video output. All topic I found regarding that are based on very old armbian version what is the way to get this working thank you for your help in advance regards Guillaume

Hello. I use Retrorange Pi on Orange pi pc+ and the kernel includes a uinput module for implementing console utility management from the gamepad. Unfortunately, in this 5.3.0-dev-rc8 core, the CPU temperature information does not work. I switched kernel to 5.4.20-current via armbian-config. In this kernel, the cpu temp readings work, but unfortunately, there is no uinput in the modules. Can I somehow build this module separately for 5.4.20-current without recompiling the entire kernel? Or is it possible for respected developers to re-enable the module in future kernel releases? With best regards, Sergey

My printer doesn't work. Armbian sees the printer but I cannot print anything. Via console command or for example Google Chrome print it doesn't work. My printer is a cannon printer. And the system is a new system, has nothing changed. As I mentioned in the title, it's a plus 2 board. Also the system is up-to-date. SOLVED ------ Installed cups-driver-gutenprint then my printer appeared on the list. "apt-get install cups-driver-gutenprint"

Hi, The OrangePI Plus 2 has 2 video output : HDMI and composite. I wander if it would be possible to use independantly these output : My goal is to have a media player on the HDMI (Kodi ?) and, at the same time, the composite image used to display my smarthome dashboard ? Thanks Laurent

Hi, all, sorry to bother you again. I still cannot make wifi on my OPi Plus2 work. The following are the results of ifonfig and iwlist scan . and my /etc/network/interfaces is as follows: What's in file /etc/wpa_supplicant/wpa_supplicant.conf : network={ ssid="xxxxx" psk="yyyyy" } and I'm sure the SSID and password are correct. I used to posted a mesage about WIRED connection, which is solved by setting hwaddress ether . However, for wireless connection, can anybody give me hand please? Thank you very m…

Dear all, My Orange Pi plus 2E was working fine before. I was able to install both the desktop / server version to the eMMC. However, one day I try to run a benchmarch & speedtest script from tocdo.net, the Pi freeze and unable to boot from eMMC ever since. I've tried to boot the Pi with an SD, it's working fine. I tried to format the eMMC - no problem at all, but when I tried to install the OS to the eMMC, it's always stuck at around 55% (for the server version) and 10% (for the desktop version). I try to run the command from URAT, SSH and the local PC itself but not working. Can you advise on this case? Below is the log from URAT: …

TL:DR Orange Pi Plus 2e USB ports are not working on newer images (LE and Armbian). Full story: Hi. I am Catota and I am new here. I am mainly a windows user with very little experience with linux. My brother recently discovered an old forgotten Orange Pi Plus 2e and gave it to me as I was looking for a media player. It has a functional Armbian 20.02.1 installed in its internal memory, but my brother does not know the passwords for either the normal user or root anymore. I installed the latest Armbian from the SD slot and it booted just fine, but the USB ports (used for keyboard and mouse) do not seem to be working. I installed the l…

Hi, this is a 5 TFT screen will work with orangepi plus ? https://www.adafruit.com/products/2453

Hello, Does anyone of you ever have done power consumption measurement or any statistic? For my Orange Pi cluster I have build up a simple circuit, to measure the total current (ampere) [1]. If all my nodes are powered off and my cubietruck and a orange Pi are powered on, the measured current is about 2A. It looks like that the Orange Pi One does not Consume a significant amount of current, if it is idle. And he is idle for about 90% of time. In case of all of that my 5 OrangePi PC nodes, the Orange PI One and my cubietruck is powered on, the measured current is about 7A what gives a power consumption of ~ 35Watt. Which is the power consumption when every node / host…

Hey all, So recently I got myself an Orange Pi Prime so I could attempt to do some SPI flashing through spidev and flashrom. I have been going at it, set up the board, got an actually decent power supply, and set up everything. Eventually I got myself into the steps of setting up the pins for spi use. At first, I used armbian-config to enable the spidev into /boot/armbianEnv.txt then I added param_spidev_spi_bus=0 into armbianEnv.txt I rebooted and the spi device file still doesn't show up, any ideas? I have: went through armbian-config (System -> Hardware -> spi-spidev) added param_spidev_spi_bus=0 to armbianEnv.txt …

Hello, I installed Debian server mainline kernel . Everything works but I am not sure about temperatures. This is output from armbianmonitor -m: 07:03:05: 1200MHz 0.00 1% 0% 0% 0% 0% 0% 55.5°C 0/8 07:03:10: 1200MHz 0.00 0% 0% 0% 0% 0% 0% 55.7°C 0/8 07:03:15: 1200MHz 0.00 0% 0% 0% 0% 0% 0% 55.9°C 0/8 07:03:20: 1200MHz 0.00 0% 0% 0% 0% 0% 0% 55.9°C 0/8 07:03:25: 1200MHz 0.00 0% 0% 0% 0% 0% 0% 55.1°C 0/8^ Is it ok or is too high ? Thank you.

Tried following this guide https://forum.armbian.com/topic/4174-full-root-filesystem-encryption-on-an-armbianorange-pi-pc-2-system/ to encrypt the root file system of a OPI R1. The system would boot to starting kernel and then just stay there. Any Ideas???

Hi, After upgrade from xenial to bionic we found a problem with R1 internal WIFI. First connection to any wireless network with nmtui works wihout problem. But after that if we try to switch to another wireless network it fails. It doesn't even reconnect to the first network ever. If we plug in an external usb wifi adapter(which uses a different driver than the internal wifi driver) it works without problem as expected. What do you think ? Have you experienced the same problem ever ? What is wrong with the internal wifi ? It was working good in xenial. I blacklisted the internal driver and using external wifi adapter for now. "wlan0" in the logs …

Armbian 5.90 Orangepi-r1 Debian buster next kernal was upgraded to 4.19.62 using aptitude (not that that matters) armbian-config wont run because it wants dpkg-reconfigure which in /usr/sbin which in not in the path. where dose this get set ? root@orangepi:/home/james# $PATH bash: /usr/local/bin:/usr/bin:/bin:/usr/local/games:/usr/games: No such file or directory root@orangepi:/home/james#

I have one of these boards: http://www.orangepi.org/Orange%20Pi%20R1%20Plus/ https://photos.app.goo.gl/1otMwG4totvNbGo88 It's kept cool with a heatsink, and fan (30-35c). Currently, I'm running the orange pi supplied version of openwrt. It's a snapshot version, so the kernel isn't compatible with some packages. My question then is, is there a script out there that can transform armbian into a router, with a firewall, web interface, and easy to use? I'd like to give it a try if such a thing exists. Sent from my Redmi Note 9S using Tapatalk

I connected the power directly to the 5V and GND pins and I tried to connect a USB modem with external power , usb-serial adapter, Flash Memory to type-C , but devices are not found. There is no problem in schematic

Hi all, I have a strange problem, when I make any file system changes, I can count to 10, pull out the power, and my changes are lost. My application sometimes requires changing of a settings file, and then quickish disconnection of power by the user (I know its not good, but it's a fact of the product) My current solution is to flush the write cache when I save the settings, I forget the command name, but that isn't ideal as other changes such as logging is lost. I'm using the armbian debian release at the moment. How can I change this write-cache timing to something like 2 seconds? Also, is this an SD-card technology issue or will the issue…

Hello everyone, first i want to say sorry if this post is not in the right place. I decided to post this in Armbian forum first, because I use it and it was awesome linux distribution with good community and support. I started as a hobby to write a software about controlling relays, to switch things in my home, like light, water heater, floor heater, etc. Hardware passes from PicoIP , thru wireless routers and finish on Orange PI, it offers a lot extras for it's price. What I have done so far: (all is in web interface, written from scratch) You can: switch on/off relays switch on/off relays for period of time schedule …

I'd appreciate some advice for using an Orange Pi running usbip as a host to extend a UPS's USB connection to a Windows desktop client on the same subnet. I've done a little research and from what I'm reading this should work but I'd like to hear which Orange Pi, arm OS and usbip version you recommend. Thanks!

I am just starting to play with my new orange pi I have it booted with this server image http://www.armbian.com/orange-pi-one/ Logged into network using Ethernet I have Wifi in USB slot but the machine does not recognize it so no ip on wlan0

i want instal peerflix on Armbian_5.41_Orangepiwin_Ubuntu_xenial_default_3.10.107_desktop, i've install first nodejs from synapsis and after install nodejs -v -> 4.2.6 i run npm -y install peerflix and if return the error message : peerflix --help /usr/local/lib/node_modules/peerflix/node_modules/parse-torrent/index.js:257 ;(function () { Buffer.alloc(0) })() ^ TypeError: Buffer.alloc is not a function at /usr/local/lib/node_modules/peerflix/node_modules/parse-torrent/index.js:257:24 at Object.<anonymous> (/usr/local/lib/node_modules/peerflix/node_modules/parse-torrent/index.js:257:35) at Module._compile…

Hello all! =) Can you help me? How can i get video acceleration in Armbian 5.9 (4.20.2-sunxi64) ? I want to use RetroArch for retrogaming and Kodi for media. By default this is slowmotion.. I know I have to install drivers for graphics acceleration. Mali,Drm and something else? Is there a list of drivers that need to be installed for acceleration? And instructions to them Thank you advance!

Hello help please. there is not sound in the headphones

Hello I`m install armbian 5.60 on my Orange Pi WinPlus and next VNS server and connect from Windows use the VNC Viever but the desktop is missing I see just this screen Not sure but meyb I instal the server version How I can check this and if it`s it`s possible to update for desktop version My SD card have only 2GB . Regards

I have been working on orange pi zero h2 daily for about a year to make a pretty good distribution but now I want to produce my console but the board only comes with headers and usb/Ethernet all soldered on making it fat, any one have a connection to the manufacturer to not make it with pins or usb/Ethernet soldered on. This is what I want my orange pi zero h2 to look like: https://www.friendlyarm.com/index.php?route=product/product&amp;path=69&amp;product_id=212 I have had bad experiences with the h3, only h2 is good for me.

After power off I have many "Module has invalid ELF structures" and there is no zram. System works, but I noticed problem because when vncserver is up almost all ram is used. How to fix it?

I've tried the EDIMax (EW-7811u) on my Orange Pi Zero. I was wondering if there is a another adapter I should be looking at or is there a working driver for the RTL8188CUS? Below is what lsusb gave me for this device. Bus 002 Device 002: ID 7392:7811 Edimax Technology Co., Ltd EW-7811Un 802.11n Wireless Adapter [Realtek RTL8188CUS] Uname Info is as follows: Linux OrangePI 3.4.39 #2 SMP PREEMPT Mon Nov 21 16:23:11 CST 2016 armv7l GNU/Linux Uname Info is as follows: Linux orangepizero 3.4.113-sun8i #16 SMP PREEMPT Tue Jun 13 14:15:57 CEST 2017 armv7l armv7l armv7l GNU/Linux ifconfig -a info: eth0 Link encap:…

hello armbian developers recently i have tried to built my own kernel from linus' kernel tree(5.18.1). the build config i use cames from armbian 22.05 bullseye(5.15.43-sunxi) /boot/config-5.15.43-sunxi ,without any changes. the kernel was ok to boot,so i plan to add xr819 support for it，but after days of work，it seems not as easy as i thought. the driver ive tried is from here(https://github.com/karabek/xradio)，but it cant detect chip's hardware revision: [ 13.036884] xradio: XR819 device discovered [ 13.038054] xradio_wlan mmc1:0001:1: no mac address provided, using random [ 13.064445] xradio ERR: FWIO: Unknown hardware: -1. [ 13.064…

Hi everybody! Need some help with understanding of some stuff in my Orange Pi zero. I have next issue: I have Orange pi Zero and Huawei4510 3g usb modem. Orange pi do some measurement and send them on server. All this stuff works great.But: my provider have session limitation(3 hours). After 3 hour i lost my orange pi from netework, but i see that 3g modem lighthing as he have connection.When i turn-off modem from usb and plug it again, he lighthing that he catch network, but services doesnt sent data. i'm using wvdial for managing network connection over 3g modem. I have script whitch reload wvdial…

Hi everyone. FIrst of all, i need to thank this community, you need to be congratulated for the effort you all make to this project. When i restart my router, the wlan0 of my opi zero 2 stops, no network with "nmcli dev wifi" appears. I've already tried restarting the service with "sudo systemctl restart NetworkManager", disable IPv6 and also installing latest armbian-firmware-full.deb, but it still the same. I'm only able to resolve it with a reboot. Previously I used Debian and this did not happen. I'm using this linux version (4.9.318-legacy-sun50iw9) because of compatibility with the SPI LCD TFT display that I'm using. From what I researched here on the …

I can not ssh into my Orange Pi Zero 2 . I get "incorrect password , permission denied" repeatedly. I have loaded latest Armbian 23.11 and some older images all with same result. I used "1234" as password. My Pc has Linux Mint 21.2 and I used Xfce terminal also XTerm. Both My Pc and Orange Pi Zero2 are plugged into same switch. Also used a laptop with Linux Mint 21.1 and Xfce Terminal with same result. Any ideas would be great , I'm just any average user that tinkers. Thanks

No wifi detected on the orange pi zero 2 Same issue as : Hardware is supported. (https://www.armbian.com/orange-pi-zero-2/) Any help is appreciated, if i resolve the issue i will post the solution here. ubuntu@orangepizero2:~$ sudo nmcli device wifi rescan Error: No Wi-Fi device found. ubuntu@orangepizero2:~$ armbianmonitor -U 1 2 ### Activated 1 lzo-rle zram swap devices with 492MB each. 3 ### Activated Armbian ramlog partition with zstd compression 4 5 ### Activated lzo-rle compressed /tmp 6 7 ### Activated 1 lzo-rle zram swap devices with…

Hello I'm new in Armbian. I'm trying to connect one Orange Pi Zero 2 to a 3d printer (board Cheetah v1.2) using UART in order to install Klipper to control the printer. I can't find how to enable the UART port to connect. I'm planning use UART 5 (pins PH2 PH3 according to this pinout http://www.orangepi.org/orangepiwiki/images/e/e3/Orange-pi-zero2-img4.png) . I've been searching for hours the right way to enable the UART communication, but I've not found a clear explanation about how to do it. I've trying armbian-config but Hardware option doesn't appears in the Menu. I'm using the Armbian_22.11.3_Orangepizero2_bullseye_legacy_4.9.318 image. Also, I've another q…

Hello. Is it possible to make hotspot at orange pi zero 2w? Just on some other boards was able to do so. I was tryed armbian-config, but there even not able to use wi-fi at all. But I sow some projets on internet and there people was able to do hotspat and they even had more options on the screen. I downloaded image from main screen ( first 2 images even didn't run on my board). Kind regards Bheatha

I downloaded the WIP armbian for Orange PI Zero. Everything seems fine that is until the wifi. Tried using nmtui. Doesn't work, can't find any network, even if I key it in. ls /sys/class/net No sign of wifi, ip link show no wifi. Tried to edit /etc/wpa_supplicant/wpa_supplicant.conf nothing Edited /etc/network/interfaces nothing. Anyone here has any solution?

I did not find the build for Orange Pi Zero 3 Vice versa I found the build for Orange Pi Zero2 Both SBCs are equipped with Allwinner H6 CPU (H618 for the board Zero 3 and H616 for the board Zero2). Is the build for Orange Pi Zero2 compatible with Orange Pi Zero 3 as well?

Problem I created a Bridge Access Point using Orange Pi Zero 3 with the Ubuntu OS. However, after going through a fairly lengthy configuration, there is an issue when trying to connect to my Orange Pi Zero 3 Access Point. The problem is: it gets stuck at 'authenticate,' and there is no pop-up to enter the password on my smartphone. Configuration Setting file system /etc/network/interfaces # Network is managed by Network manager #auto lo #iface lo inet loopback # #Eth Static Configuration #auto eth0 #iface eth0 inet dhcp # HiBob Configuration # address 192.168.6.55 # netmask 255.255.25…

Hi,o My old laptop doesn't have wifi lan card. So, i wont setup Orange Pi Zero as extend wifi lan card, or wifi bridge? wirlesss to wired ethernet How to ????????????????

Hey guys Hope everyone doing well I have a Orange Pi Zero running 21.02.2 Focal and Pi-hole installed. When I run "sudo apt update" this is the output: root@PiHoleNapoli:~# sudo apt update Get:1 http://deb.debian.org/debian stable InRelease [116 kB] Hit:2 http://mirrors.dotsrc.org/armbian-apt focal InRelease Hit:3 http://ports.ubuntu.com focal InRelease Get:4 http://deb.debian.org/debian stable-updates InRelease [39.4 kB] Get:5 http://ports.ubuntu.com focal-updates InRelease [114 kB] Ign:6 http://deb.debian.org/debian-security stable/updates InRelease Err:7 http://deb.debian.org/debian-security stable/updates Release …

I've just finished using the build tool to create an Ubuntu 16.04.4 LTS (kernel 4.14.34-sunxi) image for this Orange Pi Zero, booted from SD, logged in, and everything was going fine. Then I: Added the following to /etc/modules: g_ether gadgetfs dummy_hcd Upon rebooting the board, my iMac Pro host popped up the UI from Parallels to ask me if I wanted it connected to the Mac or VM, then the machine kernel panicked. It panicked again upon reboot until I unplugged the board. I had zero panics before I made this change. I then inserted it into my MacBook Pro and that machine panicked as well. Here …

Hi, I have Orange Pi zero, it runs while loop all time (RF Reader) and it has Flask Web Server which runs all the time. My Orange Pi Zero has 85 degree Temp. It is in the box, I wonder, what if i let device run with this temp, What happens? What about orange pi life span?

Hi all, I've been doing some stress tests to trigger the watchdog on an Orange Pi Zero and I discovered that i can reliably reproduce a kernel oops with a simple fork bomb on a fresh install of the latest Armbian Buster image (Armbian_20.11_Orangepizero_buster_current_5.8.16.img.xz) Spoiler [ 118.737219] Internal error: Oops: 5 [#1] SMP THUMB2 [ 118.742106] Modules linked in: xradio_wlan mac80211 btusb btintel btrtl sun4i_gpadc_iio btbcm industrialio bluetooth sun8i_thermal cfg80211 ecdh_generic rfkill ecc libarc4 sun8i_ce crypto_engine sunxi_cedrus(C) sun8i_di zram uio_pdrv_genirq uio cpufreq_dt usb_f_acm u_serial g_serial libc…

I'm running the newest Arbian Buster Kernel (Linux version 5.8.14-sunxi) on a Orange Pi Zero LTS. I can't get a DS18B20 running over days of experimeting. I read a lot in this forum, followed the suggestions of martinayotte and others, no success. The frustration/desperation begins to rise. Extract from boot screen: ------------------------------------------------------------------------------ Found mainline kernel configuration 32515 bytes read in 12 ms (2.6 MiB/s) 374 bytes read in 17 ms (21.5 KiB/s) Applying kernel provided DT overlay sun8i-h3-i2c0.dtbo 778 bytes read in 18 ms (42 KiB/s) Applying kernel provided DT overlay sun8…

Has anyone managed to use a usb adapter to get mic/aux out working on an Orange Pi Zero LTS? I am thinking of getting something like this (apparently it works with linux): https://www.amazon.com/Adapter-Raspberry-External-Headphone-Microphone/dp/B07R6TMQ4C/ref=sr_1_19?crid=71ETFNJN8CS8&dchild=1&keywords=usb+mic+raspberry+pi&qid=1600173433&sprefix=usb+mic+rasp%2Caps%2C200&sr=8-19

The hardware watchdog /dev/watchdog does not reboot the board in a brand new installation with 22.02 image. What happens instead is the green LED on board goes off, both LEDs on ethernet port go on and thats it - boards halt. However, if I flash previous 21.08 to sdcard everything works fine, even after I upgraded the installation via apt-get update & apt-get upgrade to latest packages.

Hi, I'm the new guy and I started use orange pi boards so go straight to the problem: I'm trying to turn my orange pi plus board into a fully function cd player.I have done the code. So when I try to connect the USB cd drive to the board and type:"ls /dev/cdrom" And it shown "ls: cannot access '/dev/cdrom': No such file or directory" that happened to "sr0" too. I don't know how to solve this Please help me.Thanks for reading this

I'm using the Orange Pi Zero Plus for a WiFi radio application and need to operate some LED's / Pots etc Ive previously used an Orange Pi Zero (Regular) and had no problem using pyA20 library or wiringpi With the Pi Zero Plus, using pyA20 gives me this error for any port: AttributeError: module 'pyA20.gpio.port' has no attribute 'PA0' or using wiringpi (gpio readall) gives me: Oops: Unable to determine board revision from /proc/cpuinfo -> No "Hardware" line -> You'd best google the error to find out why. Any suggestions appreciated, Thanks Andy

So recently i bought an orange pi zero plus2 done 3 seperate installs of both armbian buster and focal as well as tried googling the issues but i am not having any luck. i have tryed the following steps. nmtui-connect SSID. has the following response. no such connection SSID then tried to manually import it into /etc/network/interfaces. nothing changes then i tried sudo cd /etc/network/interfaces /etc/network/interface sudo rm /etc/network/interfaces sudo nano /etc/network/interfaces tryed to set up wpa_suppliment.conf no address location found sudo ifdown wlan0 && sudo ifup…

Can I power orange pi zero directly from 0 & 5V pins?

Hello. I have an orange pi zero and awus1900 with chipset rtl8814au. ( Armbian 20.11.6 Focal with Linux 5.10.4-sunxi ) I try install driver for rtl8814au as this. But I am faced with the following problems: Then i did: cp /usr/src/linux-headers-5.10.4-sunxi/scripts/module.lds.S /usr/src/linux-headers-5.10.4-sunxi/scripts/module.lds sudo sed -i '$ d' /usr/src/linux-headers-5.10.4-sunxi/scripts/module.lds And make with ARCH option with "arm". But i have now next problem:

Hi everybody, My question is about stop a running program with C. I have written a c code to start program with system() function in orange pi zero. I am starting RTKLIB software, which is STR2STR and when my code starts the software with command str2str -in serial://ttyS1:115200 -out serial:ttyS2:115200, I can stop it with CTRL^C but I want to stop it from my software. When I got a TCP pocket containing a exit status word. It should stop the STR2STR software. I am not very good at linux. How can I do that? Thanks

I'm working with an Orange Pi Zero board powered by OpenWRT with U-Boot (2018.11) and kernel (4.14.93). I'm trying to implement a recovery mode by inspecting a state of some button during an u-boot phase. This button is connected to a PL4 GPIO line. When Linux gets loaded it's possible to read a state of this GPIO line, but during an u-boot phase result is the same ( 0 ) regardless of a real state of the button (`gpio input pl4`). As I got from H2+ datasheet, L port is a dedicated port (bank) with all GPIO lines disabled by default, when I try to change value of a configuration register for this port nothing changes - I read it and see that it's the same.…

Hi everybody, I am trying to read a data on OPI Zero with wiring library. Here is my code. #include <string.h> #include <stdio.h> #include <stdlib.h> #include <wiringPi.h> #include <wiringSerial.h> #include <errno.h> char *datas[15]; char comming_buffer[256]; char command_run[256]; char veri00[10] = "serial"; char veri01[10] = "ntrip"; char veri02[10] = " "; char veri10[10] = "serial"; char veri11[10] = "tcpsvr"; char veri12[10] = "ntrips"; int k = 0; int *pk = &k; int datacount = 0; int *p_datacount=&datacount; int i = 0; int count = 0; int *p_count = &count; int data = 0; int *p_data = &…

Is the new orange pin zero 2 with the Alienware H616 supported. Board is not shown on downloads page, but that anorthern image for different board will work ?

hello my name is jean philippe, i am working with most orange pi products since i bought like 1000$ worth of them from steven 2 years ago. i have the plus, the orange pi h3, and two different a20s i am willing to work in conjunction with you guys right now, i have a (99% fully working stable .img) the only thing i cant get it of the verbose what is the file with arguments on that distro???? boot.cmd cmdline.txt uEnv.txt???? i have no clue how to shut down verbose completely since theres no grub. PLEASE HELP, would be greatly appreciated. i know, this is armbian forum, but you guys dont have the HW acceleration like the other ima…

Hi there, I have searched a bit, but didn't found HOW (step by step) make my OPi4 (with Armbian installed) an BitCoin factory. Looks it is a quite good candidate, 6 cores (2 BIG), GPU (I know, this is not Nvidia ;p). For the moment not busy doing anything. Could someone provide some kind of HOWTO on topic? (google reports small number of BC diggers for Linux). I have found some howto and (for ARMHF, not 64) binaries to make Linux machine "full" node of BC network, but not on digging BC.

Hello, everyone. Shameless self-promo: https://github.com/znoxx/torbox This set of scripts will allow you to create a tor-enabled wifi access point. Image for OrangePI Zero is based on Armbian - i just disabled NetworkManager here to allow correct execution of scripts. The idea is - you get "normal internet" from Ethernet jack, then do some TOR magic and all traffic from wifi side is "torred". Also I2P is installed to have "more darkness" in your Internets. Everything intended to be completely headless with managing via web interface, written with node.js. Have fun. For russian-speaking persons - description is here: http://znoxx.me/tor-i2p-m…

Hello, I own OrangePI board and want to repurpose it as mediacenter and computer conected to TV however multimediacenter distributions as OSMC, OpenELEC dont support OrangePi, so i decided to use ubuntu desktop enviroment from ARMBIAN according to download page it should support some level of HW acceleration for video playback So my question is - would I be able to install KODI (formerly XBMC) and use it on ubutnu desktop enviroment with working video acceleration within KODI (similar to RaspberryPi and OSMC or OpenELEC) ?? Or is there any other way to use KODI on OrangePi ? Maybe on android designed for OrangePi ? Tkanks for answers

Hi everybody, One really simple question: I got to work with wvdial and establish a ppp connection with OPi 2g-IoT but now I would like to initiate the board with the wvdial included, so if the modem 2g does not connect the board keeps trying till the conection goes smoothly. So far I've done this: sudo nano /etc/rc.local and inserted this line: sleep 60; sudo wvdial & My results are: Sometimes, mostly, it connects and works properly but there are few times like 2 out of 10 that the wvdial does not work and the board initiates without it, which I do not want at all. How can I force the board to initiate properly onl…

Hi guys i want to ask if some one know how to add this module ENC28J60 via gpio in orangepi 2g iot I did it in raspberry pi zero but it was in a different distro so now im stucked!! Thanx in advance

can i use now or in the future use arbiam with the new orange pi 3? Thanks

Hi I've got both left and right channels working of my analog audio jack. The quality is quite good as long as Master audio isn't set above volume 15 - 20 or so. Toggling DAC or DAC-Reversed in Alsamixer will enable or disable the physical left and right physical speakers of ear buds. However! On both channels, the left and right software signals are mixed. So if I use "aplay stereo-file.wav", I hear left+right mixed through my separate left ear. Listening to my right earbud, same story: I hear left+right audio mixed. Please help, I can't even find any snd_ module flags to mess with. I've no pulseaudio installed on this latest stable server edition of …

Hello. Sorry for my english. I have OrangePi3 LTS and BTT TFT35 SPI v2.1 with ili9488. I am trying to connect display to orangepi via SPI, but I dont have ili9488 driver in fbtft folder. When I am building fbtft with ili9488 from github https://github.com/Snitro/fbtft-ili9488, I am getting error. What did I wrong? uname -a : Linux orangepi3-lts 6.6.31-current-sunxi64 FBTFT Build error: root@orangepi3-lts:/lib/modules/6.6.31-current-sunxi64/build/drivers/video/fbdev# make -C /lib/modules/`uname -r`/build M=$PWD modules make: Entering directory '/usr/src/linux-headers-6.6.31-current-sunxi64' CC [M] /lib/modules/6.6.31-current-sunxi64/build/drivers/video…

I'm new to the Orange Pi 4 LTS. I work SBC's headless and have installed using UART many times on RP Zero's, BananaPi's and most recently on a RockPro64. However, I am not sure if I should be using. Is there another set of UART pins besides the "debug ins"? Booted the image on an sdcard connected to the debug pins and just got 8 lines of this stuff <��6v��Ή9�.�����goO

Hi all, I think i have made a mistake but i don't know what. Do someone know what goes wrong? Yesterday i have played with the PCIe port on the Orange Pi 4 with the original extension module. Plugged in a Dell (Ericsson) 5560 HSPA in the board and it works all fine. It was detected. Did not get the connection working with sim tray but ok. It works and reacts on AT commands. So far so good. Then i tries to plugin a wifi card (doesn't know exactly wich one. I thought Intel 6230) but didn't want to boot and a green led lights up on the PCIe board what i has never seen before. After that i thought: ''hmm, there is here laying a old Dell Latitude D630. …

I've heard people say that the Orange Pi is a "budget alternative" to the Raspberry Pi. On one hand, the Raspberry Pi has an excellent community, with a large user base that could really help you in your learning journey. On the other hand, the Orange Pi offers great value for money, and it's really tempting because the Raspberry Pi can be a bit pricey. What's your suggestion?

What is the the best reasonably priced camera module for Orangepi models these days? Raspberry has 5 and 8 megapixel camera modules from 7-30 euros. Orangepi has only 2 megapixel cameras. Or has a 5MP cameramode come available for Orangepi also? I've looked at Aliexpress and nothing seems to have changed.

I want to build an multi thread program. 1 st thread modify the GPIO, and make accurate time for GPIO pulses. (I use WiringPI OP) 2 st thread create anything else. Please write an thread example. I need thread sleep function (for 1 st thread). Expectation in the sleep the OPI CPU load=0%

Hallo, unfortunately i can't find the current orangepi image (https://www.armbian.com/orangepi/). The links to the images either go nowhere (404 file not found) or point to bananapi images. What is the correct link for the current Ubuntu image for the Orangepi? Thank you very much.

I just had an OrangePi of mine at a customer site, die on me. It just stopped responding to ping, so I made them a new MicroSD card and mailed it out. Now I think the Pi hates the Stretch release or something and fries SD cards? Check this out: https://pastebin.com/KaMk70vS Literally first login! only been up 15 minutes

Hello, I've the Pi One H3 version that I always used with a HDMI to VGA adapter that worked ok until lately that stopped working. So I was thinking to connect the board to a TV monitor having DVI connection. I've tried both stable and experimental version of Armbian o.s. and it shows the same problem, basically it boots ok at native resolution (1280x768 60Hz) until it starts the desktop GUI and it goes to "no signal". If I return to the text console mode the monitor feel the signal again and at the same native panel resolution. I've tried both HDMI to DVI adapter at the monitor side and also an HDMI to DVI adapter and using a DVI cable on the board side and noth…

Hello Everyone, Yesterday Domoticz released a new version but requires now GLIBC-2.28. Armbian Bionic has GLIBC-2.27. Users with a Raspberry Pi need to upgrade from Debian Stretch to Buster. But what i know is Armbian for the OrangePi One plus based of Ubuntu 18.04 what is based on Debian Buster. So in my opinion it should be possible to run GLIBC-2.28 instead of GLIBC-2.27. But the question is: how could i fix that?? Thank you for all help!

What's the difference between gtf and cvt ? # gtf 800 480 60 # 800x480 @ 60.00 Hz (GTF) hsync: 29.82 kHz; pclk: 29.58 MHz Modeline "800x480_60.00" 29.58 800 816 896 992 480 481 484 497 -HSync +Vsync cvt 800 480 60 # 800x480 59.48 Hz (CVT) hsync: 29.74 kHz; pclk: 29.50 MHz Modeline "800x480_60.00" 29.50 800 824 896 992 480 483 493 500 -hsync +vsync # xrandr --newmode "800x480_50.00" 24.50 800 824 896 992 480 483 493 497 -hsync +vsync xrandr: Failed to get size of gamma for output default root@orangepione:~# xrandr --addmode "default" 800x480_50.00 xrandr: Failed to get size of gamma for output default xrandr: cannot find mode "800x480_50.0…

Hi, I'm experiencing OragePI PC with Zoneminder for the development of a video surveillance system. It's possible to insert Zoneminder in armbian repository? The update of this important program in automatic mode would be outstanding. Thank you.

Hi, I am tring to build Armbian to Orangepi pc but there is no specific conf file for orange pi pc in its menuconfig? Can you pls help me to build it? Umit

Hello to everyone! I'm trying to solve the issue which is currently being discussed here and I've been forced to revert back to the ancient version in the title. The problem is that along with my OPi PC I use a cheap wireless adapter based on the MT7601. Here, I've found out that the support for these cards had been merged to upstream since 4.2 kernel versions indeed with Armbian Focal 5.10.4-sunxi it worked out of the box like a charm. Unfortunately, it isn't the case with the version I'm currently on, this adding another massive headache! I've found this really interesting thread where it is discussed how to add support for the MT7601. Everything went fine apart …

Hello! please help me with such problem. i use orange pi pc and armbian v5.36. i install kodi 15.2 from repository sudo apt-get install kodi the last version of kodi i cant install, i get problem liki this https://retropie.org.uk/forum/topic/580/solved-kodi-won-t-install-kodi-bin-depends-libcrossguid1-but-it-is-not-installable/2 soo, i install kodi 15.2 and install quasar v0.9.67 linux armv7. the last version of quasar i cant instal becouse kodi is 15.2 after i install quasar burst from quasar repository, and try search something. i got such error "cant find stream", but in log file streamin are found. this is my log file https://pastebin.com/sxTmNRc4 w…

I'm trying Monitor Mode under an orangePi pc plus which use the RTL8189FTV chip, And under armbian, After I config it as Monitor Mode, it crash with segment fault root@orangepipcplus:~# iwconfig wlan0 mode monitor Message from syslogd@localhost at Nov 6 03:13:37 ... kernel:[63339.624651] Internal error: Oops: 5 [#1] SMP THUMB2 Message from syslogd@localhost at Nov 6 03:13:37 ... kernel:[63339.740200] Process iwconfig (pid: 9670, stack limit = 0xed9a4210) Message from syslogd@localhost at Nov 6 03:13:37 ... kernel:[63339.746393] Stack: (0xed9a5d6c to 0xed9a6000) Message from syslogd@localhost at Nov 6 03:13:37 ... kernel:[63339.750768] 5d60: …

Hi all, I have the Orange Pi PC+ with installed latest armbian. system installed on eMMC. When I connect the LCD 7" ( http://www.waveshare.com/wiki/7inch_HDMI_LCD_(C) ) via hdmi to Orange Pi PC+ I only have a white screen. I do not know where I could change the settings in Armbian so that I can see the normal image on this display just like on a computer monitor. For RPi3 I knew what to do and where because it is described on wiki page for this display. Unfortunately I do not know linux well.

Currently installed PHP 5.6.30-0 + deb8u1 (cli) (built: Feb 8 2017 10:31:58) Nginx version: nginx / 1.6.2 You need to install php 5.4.45. Tell me how to install?