Beginners

It seems my OrangePi Prime was loosing stability over the years. It was working fine initially, then it was hanging up from time to time - and now it no longer can boot on stock armbian settings. It bootloops on "Starting kernel ..." in serial console. But when I set voltage to 1.3v in armbianEnv.txt - it booted ok. So it seems to be a hardware issue. Does anyone know if there is CPU VDD test point somewhere, or which regulator is responsible for CPU voltage?

I have a small group of Orangepi R2's that I'm setting up as remote snort monitors. It's my first experience with Armbian, and Orangepi and I'm very impressed. I have an odd issue that is puzzling, not of practical importance to what I'm doing, but annoying none the less. The set up I'm running is based on the main Armbian buster "Armbian_20.02.0-rc1_Orangepi-r1_buster_current_5.4.14. Linux probe1 5.4.14-sunxi #rc1 SMP Sat Jan 25 15:19:01 CET 2020 armv7l GNU/Linux I've substantially modified that to use systemd-networkd, systemd-resolved and systemd-timesyncd. My issue is that I have a dummy interfac…

On my OrangePi+2e MAME run to slow in Full screen mode!!!! When i resize window in a small resolution , everything runs ok...but when i m larging the screen , then i have a speed problems with MAME games. Is there anyone else with the same issue???

Hello, I can get the input of the card but no analog output. I'm running this image Armbian_20.11.3_Orangepiwin_buster_current_5.9.14_desktop.img How to setup alsamixer? I tried all combinations with the sliders. Thank You

I have been trying to get a 7" waveshare touchscreen to work with the orange pi zero2. I've checked that the touchscreen isn't faulty by using with a raspberry pi. I also checked that the output from the orange pi is working by using my computer monitor. It just doesn't want to output to the touchscreen (hdmi).There seems to be some thin grey horizontal lines. I do get a flicker at startup of the orange pi, but that is about it. Any idea's? I'm new to armbian, so if you have an idea, please list me some steps or point me to some documentation to help. I appreciate the help.

Armbian monitor http://ix.io/3BGM Hello updating supported bullseye 4.9 orange pi zero 2 dont work, problem with libc6 because of kernel version. I tried hacking uname -r update was successful but wont boot anymore. I use clean install with clean image from website : dpkg: error processing archive /var/cache/apt/archives/libc6_2.31-13+deb11u2_arm64.deb (--unpack): new libc6:arm64 package pre-installation script subprocess returned error exit status 1 Errors were encountered while processing: /var/cache/apt/archives/libc6_2.31-13+deb11u2_arm64.deb E: Sub-process /usr/bin/dpkg returned an error code (1) …

I'am currently trying to install a desktop version of armbian focal on armbian-config, the only option avaliable is Desktop, but when i install it and reboot, it comes back to console i am running it on ubuntu terminal (Screen), because i can't use my TFT LCD monitor (don't know why either) Anyone had this problem? is there a fix?

Hi, I need to configure a GPIO as input with pullup enabled and tried https://forum.armbian.com/topic/10462-nanopi-neo-2-set-input-pull-up-via-device-tree/ For some reason PIN PG06 is still floating. It is not pinned to 3,3V. PG06 -> GPIO198 -> UART1_TX/PG06 right? Multimeter shows ~0,447V /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; /* * This fragment is needed only for the internal pull-up activation, * external pull-up resistor is highly recommended if using long wires */ fragment@0 { target = <&pio>; __overlay__ { input_0: input_0 { pins = "PG6"; …

Hi, First of all i'm NOT a software developer and i have NO one skill on this kind of board's hardware... I've a good soldering skill, so just for fun i've bought a new RAM module for my OrangePi Zero Board... I've bought a K4B4G1646E-BYMA RAM module and then i've replace the onboard module... All of the work gone fine, the OrangePi Zero still boot and work perfectly, but i was hoping to upgrade the RAM on the board... After the boot, in the welcome screen the, the RAM amount is now 512MB (494MB) and before was 256MB... The RAM amount is now increased, but not like expected... I've choose the K4B4G1646E RAM module because, theoretically, it was a 4GB RAM m…

Hello. First, I have an LTS board that provides only 3.05 on the 3.3 pins. Is it normal ? Anyway, in case this was the issue, I have built a new voltage regulator, and now supply the DHT22 and pullup resistor with 3.60V My issue is simple: when plugged on normal 1W bus, the DHT22 kills the bus, and makes other devices non working. I have moved all other devices on a new bus, leaving the DHT on a bus I know works fine. Some people mentionned the DHT is not compliant with official 1W libraries, and can not be recognised with normal timings, so, special libs are required. I have removed param_w1_pin=PA06 for the hysical pin 7, and installe…

Hello, I have an OrangePi Zero that installed apache2 and PHP 7.0.33-0+deb9u1. I have also a NextCloud server installed. After update of NextCloud to 15.xx, system status shows me a warning about PHP version. I have tried update to newest PHP (7.1 or newer) but there is no newer version than PHP 7.0.33-0+deb9u1 on Armbian repo. Do I have to wait update from Armbian repo or can I update it from PHP's offical releases ?

Hi This issue is produced on both flavors of Linux for the orange pi zero i.e. Debian and Ubuntu. I am trying to login to pi zero using the serial terminal. First time it asks me to change the password, which I changed. Then using that changed password I tried to login into it. However, whenever I enter the password in it. it restarts. I even used the external high power phone charger to test this issue but in both cases result was same. Any solution to this problem?

Hello there, I am looking a way to get / write a script for the file to be run on startup. I am running PiAware with dump1090-fa installed. I would like to having the view1090-fa --modeac to be auto run when the system is ON. Is there a way to get this work without my concern in the future? Currently if I need to run this command, I need to run SSH and remote the Pi to run this command from my PC. Thank you in advance. Regards, SaiHou

Hi I'm trying to use OpiZero with a relais module. I noticed, during the boot the pins I tried (12 and 11, physical 3 resp 5) go high, which makes impossible to manage the relais module. Is it a HW/SW bug or limitation or something what can be configured somehow. I would expect the level to be "nothing" ;-) Thanks Chris

I would like to use the uart of the orangepi zero 2 for an application. It esists for example /dev/ttyS5. But unfortunately the communication does not work. When I connect minicom to this port and short the two pins 8 and 10, I wanted to see the characters that are sent. Minicom can be connected (minicom -D /dev/ttyS5). But the characters are not mirrored. Do I need to enable the UART before? How to do this? The orangepi-config program does not exist on the system. The system reports after the login with: Welcome to Orange Pi 3.0.6 Bullseye with Linux 5.16.17-sun50iw9 Thank you for your thoughts.

I'm using OrangePi-Lite2 board with image : Armbian_20.08.1_Orangepilite2_buster_current_5.8.5.img Most of the functions that are important, do work well as of now. There are two major issues : 1. I setup my Bluetooth headset from armbian-config and it is paired and connected and I'm able to output a .wav file using aplay etc. However, I can not record anything from the microphone with arecord. No devices are listed for recording. But when I connect a USB microphone to the board, I can record well with arecord. Bluetooth record function is very important for me right now. Appreciate any pointer as how to get it to work. Thanks. …

I have several Pi3s and two Asus Tinkers. They work well, Tinker is a bet better of the two. Want something fast to use with my 3D print. and Octoprint etc. So want to run CAD software, Slicer etc. and control of my Creality CR-10. - So, I bought OrangePi and had bad initial experience, and boot SW was in Chinese. So I returned it and got their best? The OrangePi 2 Plus. - Should have been better. My experience is it is very very temperamental. I found, and I see others have experience power supply issues. 1. Must make sure the 5V does NOT go below, 5Vs. The average current runs between .5 and .8 Amp. but there are large peaks. I used a 3A raged supp…

Hello everyone, I have a question. It is about SSD memory, which can be connected to the usb3 interface via a converterbox SATA 1,2,3 to the OrangePi3 device. I did not find any helpful information in the hardware recommendations inside the Arbian Forum for OrangePi3 H6 all winner (looser). Before I jump into the cold water like with my RPI 4b+, I am interested in which SATA 1,2,3 adapter to SSD to USB3 works with the OrangePi3 devices. I already know that the NVME slot and memory is not supported. And a usb3 converter with SSD additionally absorbs power. Thanks for Help

Two days ago I was able to build a minimal server installation of Bullseye Armbian for this board with no problems. My sd card crashed and I built the img file in tmp on a VM machine, so no backup (I know, live and learn). Last night I tried building this img again, minimal server, desktop and all the bells and whistles, but it keeps failing. Here is what I get: LD [M] drivers/staging/rtl8723cs/8723cs.o AR drivers/built-in.a GEN .version CHK include/generated/compile.h UPD include/generated/compile.h CC init/version.o AR init/built-in.a LD vmlinux.o MODPOST vmlinux.symvers MODINFO modules.builtin.modinfo GEN modules.builtin LD .tmp_vmlinux.kallsyms1 sc…

Hi all! Sorry about my English. I just started learning Armbian. Please don't scold me for my ignorance. I have an Orange Pi 3-lts. I installed an "Armbian_23.02.2_Orangepi3-lts_bullseye_current_5.15.93" OS on it. Transferred everything to EMMC. Installed Clipper. I started experimenting with the rotation of the display. (everything seems to have turned out as I wanted!) But damn! Wanted more! I wanted the startup process log to not be displayed on the screen when the OS was started. I read somewhere on the Internet: change in armbianenv.txt console = botn on console = serial. I listened and changed. And now I can't manage my OPI. I can't connect via terminal b…

I have attempted to install OMV on my orange pi various times and i have had the same issue weather with the OMV after installation or with the armbian os before the OMV installation. when you start the system, it just won't get it's Ip automatically, at first i thought my orange pi came with a problem from fabric since I'm new to this but after attempting to put an Ip statically seemingly making it work I noticed that it just would not be set automatically. Now surely you might think it's a problem with my router set up, but this won't happen when I try it out with any other equipment in my house or when i just run regular Linux in my laptop, even when i run the OrangePi…

Hi im having problems when booting armbian on my OPI5P it is just blinking green and not showing a picture. I am using this version of Armbian: Armbian_25.5.1_Orangepi5-plus_noble_current_6.12.28_gnome_desktop.img and I have tried it on all boot media i have available (NVME, USB and SD card) but none worked. Sorry if there are any gramatical errors, I am from germany and my english isnt the best.

hello, root@orangepipcplus:~# cat /etc/armbian-release BOARD=orangepipcplus BOARD_NAME="Orange Pi PC +" VERSION=5.23 LINUXFAMILY=sun8i BRANCH=default ARCH=arm Hello everybody, I have sucessfully copy the armbian to the emmc memory, everything working well no sd needed .... when this is done I make a backup of the emmc with gunzip on my sdcard. dd if=/dev/mmcblk0 bs=10M | gzip -c >/mnt/sdcard/thx.to.kaiser.img.gz the backup on the sdcard working well, I exact it on a new sdcard with the command gunzip -c /mnt/sdcard/thx.to.kaiser.img.gz | dd of=/dev/new-sd-card bs=10M find ... the armbian os working on the sd card ... but when I try to put the emm…

If I would like to build myself an image with all content present in images posted on web, downloading code at https://github.com/armbian/build and choosing my board, when I build image if I don't change anything I will get what I want? Thanks

My Orange Pi PC is restarting without apparent reason at random times and wifi and buses are disabled. The last lines of log always say the same: [ 25.644949] IPv6: ADDRCONF(NETDEV_CHANGE): wlxf4f26d1c6002: link becomes ready [ 33.781109] vcc3v0: disabling [ 33.781136] vcc5v0: disabling [ 33.781146] usb0-vbus: disabling armbianmonitor link: http://ix.io/2mTA Thanks in advanced

i can't change default english os lanhuage. i set and download my home language... dowloading language files,finish added to list, i tap apply wide-system change effect after next login..okay here problem! i try logout and re login, system don't change language i try logout and restart board...language not changed... why not change system the english language to other?

orangepiplus2e: I have been using an OS that i downloaded in the usa. Now I am in ukraine and after i do an update & upgrade, which does run through, the OS tries to connect to the internet, but fails; the page tries to open, but all i see are a few lines of the internet homepage i connected to. So, it does go to the page, but won't open it. I have tried multiple times using different url's. During the update, the OS upgrades to the current version, Buster 10.7. I downloaded a new OS from both "usa" & "europe", but upon trying to install it, i got a "ua" keyboard screen message for both usa&europe, and i had to choose an…

Hello all, earlier I booted up the board (Radxa Dragon Q8B) when it prompted to reboot & update and I allowed it. The update took uncharacteristically long. The OS is running off an SD card. There is no SSD or eMMC installed. Turns out it wiped the install clean. There was about 20 GB of free space prior to the update, now there's 46 GB. For some reason the user itself and the wifi login are still there, but everything in the home directory is gone. Installed applications and the driver for the wireless card are gone. Chrome add-ons are still there, but reset. The Downloads folder now has Armbian_26.8.1_Radxa-dragon-q8b_resolute_vendor_7.0…

Hello, i am very new to using armbain. I picked up an orange pi lite and loaded armbain debain jessie using etcher on a 16gb card. when i install it to the orange pi lite and power it on it asks me for a user name and password. i did as instructed using rot and 1234. then i added my name and made a new password as instructed. it then acts like its booting and says orange pi lite on the screen but wont boot the GUI desktop as it describes. it displays the name and some of the current states of the board (temp ect) but then sits at a command prompt waiting for input. i can type help and it will give me a list of commands that work for it but none indicate they will boot the…

Hi, I've had orange pi one laying around and also couple of camera modules scrapped over different devices, which only one seems to be the "known" model of ov2640, which is supposed to be supported on linux mainline kernel, but unfortunately no module is compiled into armbian image, so I've had to compiled it solely for the running kernel. After lot of digging into the thing, mostly getting inspiration from this forum and threads about 5640, I've tried crafting overlay, with different results. This is the latest attempt, which created /dev/vide0, but no /dev/media0 is made, and also loading module fails with: [ 5812.695851] ov2640: loading out-of-tree modul…

Upgrading to the latest Armbian build 5.15.25 on the M2-Zero has caused the camera to stop working. I had a build from https://github.com/Qengineering/BananaPi-M2-Zero-OV5640, and ive seen my camera work with Gstreamer but i now need it to use the hardware encoding. So i used https://wvthoog.nl/nanopi-ov5640-camera/ to enable the Cedrus encoder, but upgrading the devices loses the camera and /video1. There is no /video1, or media1. Ive tried to edit the dts files, build and push them but no luck. Any advice here would be good. I know there are a few topics on here on this subject, but they are all slightly different issues because of the ke…

Hi i try to get a ov5640 camera running on a banana pi m2 plus board. i builded the csi driver and it gets loaded, however i am not able to take picture: root@bananapim2plus:~/cap-v4l2# ./cap 1280 768 4 1 -999 -1 -1 ---- cap parameters ----- width: 1280 height: 768 v4l2 buffers: 4 exposure: -999 hflip: -1 vflip: -1 Mode: V4L2_MODE_VIDEO Driver: "sun6i-video" Card: "sun6i-csi" Bus: "platform:camera" Version: 1.0 Capabilities: 84200001 v4l2: unable to enumerate input. v4l2: failed to init camera. root@bananapim2plus:~/cap-v4l2# dmesg [23141.993618] sun6i-csi 1cb0000.camera: -> sun6i_csi_set_power() [23141.993653] sun6i-csi 1cb0000.camera: -&gt…

Hi, I am using OV5640 in Nano PI duo 2 kernal: Linux nanopiduo2 5.10.16-sunxi #21.02.2 SMP Sun Feb 14 21:12:17 CET 2021 armv7l armv7l armv7l GNU/Linux I found that NanoPi Duo2 - FriendlyARM WiKi which is kernal 4.14 supports camera OV5640. Do Armbian Focal (mainline based kernel 5.10.y) have support? if not Please say how to do it? I am new to this armbian kernal Thanks in advance

Hi , We are working on sochip s3. We are trying to interface a new sensor( CSI - MIPI ) with S3 chip with interface add a new file for a new sensor. Required changes : Change in .fex file, change twi_id and twi_add. Also, change module name and address at module load time. $ insmod /lib/modules/3.4.39/vfe_v4l2.ko ccm="ov8856" i2c_addr=0x6c But we got below an error : [ 19.888515] [VFE CCI_0 ERR] Status error at addr_8bit = 6c, wr_flag = 1, val = 1000a30 [ 19.888764] [VFE CCI_0 ERR] Status error at addr_8bit = 6c, wr_flag = 1, val = 1000a30 [ 19.889007] [VFE CCI_0 ERR] Status error at addr_8bit = 6c, wr_flag = 1, val = 1…

After apt-get upgrade I got 4.14.18-sunx installed on my organge pi+. docker daemon won't start. I tried removing and reinstalling it. tried dev, next and nightly builds to no success. docker gives an error that no overlay fs is available in kernel. tried ARMBIAN 5.60 stable and 5.64 nightly >apt-get install docker-ce fails with Setting up docker-ce (18.06.1~ce~3-0~debian) ... Job for docker.service failed. See 'systemctl status docker.service' and 'journa lctl -xn' for details. invoke-rc.d: initscript docker, action "start" failed. dpkg: error processi…

So, i managed to boot from ssd, run docker ... after issues with usb port connection i desided to apt-get upgrade.... then stuff happends that i do not really understand. As i try to run docker afterwards there seems to be an issue with the storage-driver overlay2. I tried a- lot of fixes... but do not want to lose the containers and images that i used in docker. A lot of time has gone in to configuring ( and figureing? out) I cannot solve how to get the issue solved. Help! this man is desperate. How do i start?

Hi, I am running OrangePI lite with 5.65 Xenial. I followed tutorial on using overlayroot here "How to freeze your filesystem". However, when I run overlayroot-chroot to make changes, I am getting the following error when I modify files: "Read-only file system". Here is output of 'mount': /dev/mmcblk0p1 on / type ext4 (ro,relatime) proc on /proc type proc (rw,nosuid,nodev,noexec,relatime) tmpfs on /run type tmpfs (rw,nosuid,noexec,relatime,size=50696k,mode=755) sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,relatime) I tried running mount to make it read-write: mount -o remount,rw /dev/mmcblk0p1 #make changes, revert back mount -o remount,ro /dev/mmcb…

Hello, I have enabled overlayroot using "armbian-config" command line tool (in my orangepi PC). My current OS is Armbian Focal xfce desktop After rebooting, I noticed that the entire filesystem stills writable. I checked the content of ( /etc/overlayroot.conf) using; cat /etc/overlayroot.conf this command show at the end of the file these two lines: (after commented content): overlayroot_cfgdisk="disabled" overlayroot="tmpfs" If I well understood, normally, with such a configuration, the filesystem should be set to read only., but in practice, it is not. Could you assist me how to resolve this problem?

Time_2018/02/26 OrangePI PC2 Armbian_5.40_Orangepipc2_Ubuntu_xenial_next_4.14.15_desktop s problem OrangePI PC2 Armbian_5.40_Orangepipc2_Ubuntu_xenial_next_4.14.15_desktop was downloaded yesterday. It was started and seen once again. Fortunately, language support, they seem to move, it was. 1. fumio@orangepipc2: ~/Desktop$ df -h filesystem size user Avail Use% Mounted on ............... tempfs-root 498M 498M 0 100% /media/root-ro overlayroot 498M 498M 0 100% / ...... ..... tempfs-roo and overlayroot…

Hello all, my boot partition contains following file structure: # ls -lh insgesamt 20M drwxr-xr-x 3 root root 4,0K 11. Nov 16:27 ./ drwxr-xr-x 3 root root 4,0K 16. Nov 09:24 ../ -rw-r--r-- 1 root root 38K 8. Okt 22:10 boot.bmp -rw-r--r-- 1 root root 14K 27. Okt 16:52 boot.ini lrwxrwxrwx 1 root root 21 8. Okt 22:10 dtb -> dtb-5.4.151-odroidxu4/ drwxr-xr-x 3 root root 4,0K 8. Okt 22:10 dtb-5.4.151-odroidxu4/ -rw-r--r-- 1 root root 0 8. Okt 22:10 .next lrwxrwxrwx 1 root root 25 27. Okt 16:58 uInitrd -> uInitrd-5.4.151-odroidxu4 -rw-r--r-- 1 root root 13M 27. Okt 16:58 uInitrd-5.4.151-odroidxu4 -rwxr-xr-x 1 root root 7,0M 8. Okt 21:52 …

Hi! When I try to run overlays on Armbian 21.08.2 Focal, they do not seem to load, see attached screenshot below for the output during boot. It looks to me that fdt is not properly run or sth. root@rockpro64:/boot# cat /etc/os-release NAME="Ubuntu" VERSION="20.04.3 LTS (Focal Fossa)" ID=ubuntu ID_LIKE=debian PRETTY_NAME="Armbian 21.08.2 Focal" VERSION_ID="20.04" root@rockpro64:/boot# cat armbianEnv.txt verbosity=1 bootlogo=false overlay_prefix=rockchip rootdev=UUID=73fac48d-4f73-4ac1-b899-e67dc98b5794 rootfstype=ext4 overlays=pcie-gen2 spi-spidev extraargs=net.ifnames=0 isolcpus=4,5 usbstoragequirks=0x2537:0…

I use Armbian Buster on ODROID-C2. I try to install the package "syslinux" with apt, but it's not there. What now? apt install syslinux Reading package lists... Done Building dependency tree Reading state information... Done Package syslinux is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Package 'syslinux' has no installation candidate

I have done a flat install of "Armbian 24.11.2 Bookworm Minimal" but for some reason it keeps failing to update. I get the following output and I can ping the IP address but when I try to follow the http address it show s a 404 error in the browser. Is there something I am missing as I have tried to fix it but not sure if its just me or everyone is getting this as the file is missing to download. root@orangepi5-plus:~# apt update Hit:1 http://deb.debian.org/debian bookworm InRelease Hit:2 http://security.debian.org bookworm-security InRelease Hit:3 http://deb.debian.org/debian bookworm-updates InRelease Hit:4 http://deb.debian.org/debian bookworm-bac…

Hi, I've bought a pandoo box with an amlogic s912,2 3g of ram and a mali t820, I've found a couple of dtb files (vegas and meson-gxbb-p200.dtb I think) that make it boot but without wifi nor bluetooth, I've tried extracting the one from android using termux and dd /dev/dtb with no luck... is there anything else to try? any way to make wifi and bt work? Any help is appreciated Thanks!

Hello! I have Armbian running on a Lime2. It runs from the microSD. The board has eMMC and I have also connected a SATA SSD through USB because I would like to move the system to the SSD. I have tried doing so through the nand-sata-install.sh script but it always shows the following message: There are no available partitions. Please create them. I get that message no matter if I choose to have the boot partition on eMMC or on microSD. And I don't know much about partitions. What partitions should I create? Where should I create them? How should I create them? Thank you!

Would passive cooling be any good for OrangePi PC Plus? Or active cooling is better suited?

No me deja entrar .. no lo entiendo !! Me dice que la contraseña es incorrecta. ¡¡Por favor, ayúdame !! : o Translation : He doesn't let me in ... I don't understand! It tells me that the password is incorrect. Please help !!

I am adding support for a new board: NanoPi R2S Plus. I have added it to the kernel and it works in testing so far. Now I am attempting to add the new board to u-boot. The u-boot configuration for NanoPi R2S does not enable the eMMC and I want to install to boot from eMMC. Using my modified kernel and u-boot for NanoPi R2S I am able to run armbian-install because in the system booted from SD card the eMMC is enabled. But after installing to eMMC, shutting down and removing the SD card, boot fails because u-boot cannot access the eMMC. Looking at the device tree for NanoPi R2S in u-boot, not surprisingly, eMMC is not enabled: NanoPi R2S does not have eMMC memor…

I am using Armbian 23.5 Jammy XFCE on a Tinker Board 2S. I have a number of issues to sort, one of them being display. The display is receiving a 16:9 signal, but the right hand side of the screen is covered by a black-white-green pattern under which I can move windows (image attached). How can I change the settings to avoid this?

Hi I have simple question. If i got power loss while executing nand-sata-install my cubieboard2 is dead now or there is some way to recover it? I have the same cb2 board. I install armbian-legacy-kernel-line. @admini know cb2 is EOL device but please give me a chance to get answers. thx :-)

Hi , My son purchased a PCdunio v3, wifi enabled with his birthday money with the grand plan of "coding". This idea is slowly going down the drain. It is using Ubuntu 3.4.79+ It does not detect any wifi or ethernet. I have confirmed that both interfaces are up. I have tried with and without the SD card. I confirmed the router is not blocking the device. I can see that the State of wlan0 is unmanaged, but cant figure out how to fix that. I have tried manually creating entries for the network but this was unsuccessful. When it does try to connect to Wired Network, it simply got stuck looking for an IP address and never amounted to anything (Nothing in the ro…

Hi everyone, I've updated my pcDuino via: Sudo apt-get update Sudo apt-get upgrade I can reach 8.8.8.8 from the terminal and google.com from the Chromium browser. However, I cannot reach any other website. I am guessing it has to do with the latest TLS requirements. TLS 2.0 is required for 99% of global websites. I'm presuming my pcDuino is on an older version for TLS 1.0/1/1 Any thoughts or help is greatly appreciated Thanks

I am new to arm devices. I'm trying to build a fully working armbian system for the pcduino8-uno which uses the Allwinner a83t/h8 soc. I know these are not the best, but I got it from amazon for $18 and it runs home assistant very well. I built a new u-boot which appears to initialize the hardware properly as it sees all the usb port as well as obtains an ip from my dhcp server. Using sun8i-a83t-allwinner-h8homlet-v2 as my starting point.. I built a new kernel from 6.1.0-rc6. Everything seems to work properly except the ethernet controller. I can use a usb ethernet dongle, but I would like to get the onboard working Dmesg shows " [ 1.59462…

hello dear All, first of all - i am very glad to be here in this great forum. i have heard that i can run Armbian on Orange Pi as well. And i have also heard some thing regading H6. The implementation of the PCI Express controller of H 6 is known to be broken. Is it still the case. Is there any extended H6-support through armbian?

hi there! im a beginner in the linux world, but to try to learn a bit more and to try to make something useful im currently lookin at a orange pi 4 board in hope to somehow turn it in a NAS/Emby server. i played a little with the Opi4 and it looks promising, the only problem is that it doesnt have sata ports. i can get an extension board to plug in a mPCIE device, and i was planning to use it to connect a PCIE-Sata device. since i still have to buy it, do you have any suggestion? i looked at the JMB585 and the ASM1166 expansion boards, they both have plenty of ports for what i need and the speed its more than amazing, but i would like to know if they are …

Hi, I'm struggling to get sound with a PCM5102a module connected to I2S. I guess I've to make a dts-overlay to enable it on i2s0 but I didn't succeed, I'm very new to that. Could anyone tell me how to achieve that ? Many thanks for your help.

I would like to permanently change at start up the UART permissions of /dev/ttyAML0 to give user, read write permissions always. I can do this with the usual "chmod" command but this gets reset after every boot and sometimes also during normal operations. Can somebody direct me to how this can be done please? xuraax

Hi, I ran into an issue when configuring ssh. As it seems, ssh listens only to the first interface that is enabled (it seems it is always eth0). Probably, if I set a listen to 192.168.x.x in the config file of the sshd (same as the IP set in the wlan0), and a different network on the ethernet, it would work, but as I won't be using ethernet I would rather disable it completly. I tried already ifdown, ifconfig down, ifconfig eth0 down && rmmod -f sunxi_gmac, and some others. I even tried removing nmtui just to check if that was causing the problem. all what that step does is removing the bond0 interface (something I would like to do too). I checke…

Hello. I have "Debian GNU/Linux 9 (stretch)" on CubieTruck. After installing Apache2 i get problems with /var folder (that is symlink on hdd folder). Apache2 dont see files in it. So i print stat for this folder from commandline and from php in Apache. That is from command line: root@cubietruck:/mnt/var/armbian/apache2/www/html# stat /mnt/var/armbian/var File: /mnt/var/armbian/var Size: 4096 Blocks: 8 IO Block: 4096 directory Device: 801h/2049d Inode: 2097154 Links: 13 Access: (0755/drwxr-xr-x) Uid: ( 0/ root) Gid: ( 0/ root) Access: 2018-02-10 14:35:14.025501481 +0300 Modify: 2018-02-04 09:1…

Hi! I need to use PHP 5.3 that is requiriment of old version of vtigerCRM. How to install it in Armbian?

On my Odroid C4 with Armbian Buster runs a nextcloud version 23. Buster brings php 7.3 and I have to install php 7.4. How to do this? Thanks for your help!

Hi all, I've installed ISPConfig by the "armbian-config" menu I created several sites on my web server installed in debian Buster and ISPConfig 3.1.15p3. I would like to use phpmyadmin to create an independent database at ISPConfig. When I try to start phpMyadmin (http: // myipadresse / phpmyadmin), I get a 404 error message. I found this post: https://www.howtoforge.com/community/threads/phpmyadmin-404-not-found-debian-9-3-ispconfig-3.78145/ I applied the first line without difficulty (ln -s /etc/phpmyadmin/apache.conf /etc/apache2/conf-available/phpmyadmin.conf). The second line (a2enconf phpmyadmin) gives me an error again: "ERROR: Conf phpmyadmin does n…

I have the 'Full Featured Version' of these boards: https://www.phytec.de/produkt/single-board-computer/phyboard-segin/ Featuring an i.MX 6UL-G2 CPU, Arm Cortex-A7 with 512MB Ram. Has anybody here tried running armbian on these?

Good evening, Armbian noob here (Debian veteran) working with an RPi 5. I've just installed `Armbian_24.2.5_Rpi5b_bookworm_current_6.6.23.img.xz` and would like to build the ZFS modules. I've installed the kernel modules using `armbian-config` but when I try to build I get root@meson:~# dpkg-reconfigure zfs-dkms Deleting module zfs-2.2.3 completely from the DKMS tree. Loading new zfs-2.2.3 DKMS files... Building for 6.6.23-current-bcm2712 Module build for kernel 6.6.23-current-bcm2712 was skipped since the kernel headers for this kernel do not seem to be installed. root@meson:~# Edit: Current situation: root@meson:~# dpkg -l linux…

I have a raspi hat (rak2245) that has 2 versions: a pi-hat version that has a 40 pin-header on it for raspberry pi's , but also a smaller stamp edition. It uses spi and uart to communicate with the pi. I have it running without issues on my orange pi zero, even though the pinheader is a little too large. And via a breadboard I can access all pins just fine. But since I am making my own PCB anyway, I am interested in using the stamp version. The only difference between the stamp and the pi-hat version (aside from the form-factor and pin-out) is that the pi-hat version has an additional eeprom chip to tell the rapsberry pi about the function of the pins apparently. Now…

Hi evereyone, After doing some upgrades my Pi-hole Admin Page was not reachable anymore, while blocking still worked. 1. Problem The lighttpd service was not running because of the missing folder /var/log/lighttpd. So lighttpd crashes when trying to access /var/log/lighttpd/error.log and access.log. Reinstalling Pi-hole and lighttpd didnt solve the problem. So I first created the folder myself: sudo mkdir /var/log/lighttpd sudo chown -R www-data: www-data /var/log/lighttpd Then I reinstalled Pi-hole and lighttpd, now lighttpd was running. Unfortunatly now I ran into 403 - Forbidden when accessing…

Hallo After apt-get upgrade my pi-hole and transmission is not working. Both running and I can see it when type htop. But I cant use web interfaces. It is without graphic.

Hi use a Nano Pi Neo with the Debian Server Image and and want to try install Pi-Hole but while the Installation Process i get a Error. The Script cant add a Password to the New User that Pi-Hole require (Yes i am use Root) i get a Stunnel4 error ?!?! Thanks for your Help

Hi, does anyone have experience of using this: https://ru.aliexpress.com/item/Raspberry-pi-2-HIFI-DAC-I2S-Interface-Special-HIFI-DAC-Audio-Sound-Card-Modulecompatible-raspberry-pi/32652350376.html device on Orange Pi PC Plus I have modifyed script.bin file: [twi1] twi_used = 0 and [pcm0] daudio_used = 1 Then i saw in pulse audio new device, called "sndaudio" aplay say this: root@orangepipcplus:~# aplay -l **** Список PLAYBACK устройств **** карта 0: audiocodec [audiocodec], устройство 0: SUNXI-CODEC sndcodec-0 [] Подустройства: 1/1 Подустройство №0: subdevice #0 карта 1: snddaudio [s…

Hey everyone...I've tried searching the problem I'm having and have tried different things...all so far to no avail. I'm relatively new to learning about pihole and decided to go out and buy the kit from ameriDroid (maybe should have built my own but decided to go this route to try and save myself some time). I received the kit today and started following the install instructions (I am attempting to install via SSH thru Putty). Once I reached the install command, I get an error stating: "Error: Unable to update package cache. Please try "apt-get update". I've tried the apt update/upgrade and I'm still getting the same error. The output from th…

Hi Folks! Thanks for the great software. Install went very smoothly and my board is stable. Last step is to enable my DAC card. I know that it is used in the Volumio image for this board ... so I assume (!) that support is in Kernel already. Any hints on how to get it working? I was digging around for a dtoverlay to enable ... but no luck so far. thanks!

Hello Unfortunately my OrangePi PC which I used for couple of years failed and I'm looking to buy the 64-bit SBC from Pine64. Funny thing about my OrangePi PC was that there was one and only one old Armbian image version (Armbian-20.05.4-Orangepipc-focal-5.4.45.img) which ran GUI successfully out of the many other Armbian and OrangePi images I tried which helped me run it as a desktop for using Libre office and others. Unfortunately 1GB RAM was too low for Gaming lol. Thanks to the Armbian community for that. Before buying, I presume the PineA64 LTS version has a 64bit Rambus if not - I don't understand how processing speed will be bett…

Hi Everyone, I have a clean install of armbian with vanilla gnome installed, it boots to the login screen and mouse seems fine but after a few seconds it stops responding and when you move it it does this weird rapid shake movement as if your moving the mouse like 2 pixels side to side 100 times a second, its hard to explain but the curser doesn't move. Every reboot and the same thing happens and I tried starting from scratch with a fresh flash but same results happen and also tried different mouse, they work fine on other machines though. Has anyone come across anything like this before who can possibly offer some advice? Sorry if I haven't explai…

I need to use VideoLAN VLC on my Pine64, with Armbian Buster. When I play an H264 mkv video, I got images too slow, and then it stops (like freeze). I think there is no hardware acceleration. When I start with mpv through the command: export VDPAU_DRIVER=sunxi mpv --vo=vpdau --hwdec=vdpau --hwdec-codecs=all filename.mp4 I got this: Playing: test.mkv (+) Video --vid=1 (*) (f) 'TST' (h264 1920x1080 23.976fps) (+) Audio --aid=1 --alang=eng (*) (f) 'ENG EAC-3 6ch @640kb/s' (eac3 6ch 48000Hz) (+) Subs --sid=1 --slang=eng (*) (f) 'ENG FORCED' (subrip) Subs --sid=2 --slang=eng 'ENG FULL' (subrip) File tags: Title: test [vo/vdpau] Error when…

I have been using the Pine64 2Gb computer as an automation server for a couple of years now. Purchased it when first available. A bit long in the tooth wanted to upgrade these days to something smaller and faster. Meanwhile here have changed power supply to using the Euler pins and put heatsinks on the device chips. Looking to overclock this device and have not been able to. Welcome to ARMBIAN 5.76.190310 nightly Ubuntu 18.04.2 LTS 4.19.25-sunxi64 pine64:~# uname -a Linux pine64 4.19.25-sunxi64 #5.77.190324 SMP Sun Mar 24 20:09:19 CET 2019 aarch64 aarch64 aarch64 GNU/Linux Well can I ove…

I have a Pine64 A64+ (2GB RAM version) with Armbian 5.75 installed. After creating the SD card image networking works perfectly, but then after a few days it just stop connecting to the Wi-Fi network. Troubleshooting Wi-Fi: I can see the APs in the GUI and also using the armbian-config tool. When using armbian-config: Network -> Select default interface = wlan0 -> WiFi -> I select my home Wifi and press Return key : it says `Connecting...` then after about 30 seconds: `Could not activate connection: Activation failed: The Wi-Fi network could not be found` Troubleshooting Wired connection: …

pine64 products have sloppy DC connectors. This connector simply detaches from the motherboard. I use in production pine64 pine64-lts pineH64 and rock64. As a result of switching on and off the dc connector, in each case it has peeled off and does not hold power. I've attached the DC connector with glue but that's not what the factory mount. The low price now goes sideways. workmanship worse than nonopi.

I'm trying to get OctoPrint to work on my Pine64 to control my Qidi i-mate(s) 3d printer. I've done a fresh install of Armbian on the Pine64 with no problems. I'm not sure where to go to troubleshoot the USB-ttl serial connection. I've double checked that the cable is installed right on the Qidi motherboard, this application doesn't need the vcc connected so the other three are. I've tried enabling the UART's in the armbian-config with no luck on the connection. While I've used Linux for quite some time, I'm not familiar with this sort of thing and I'm not even sure where to start the troublshooting. I can easily provide additional logs. This is on an …

Dear all, I'm using Armbian_5.25_Pine64_Ubuntu_xenial_default_3.10.104_desktop. The default display resolution of 720p60 is working fine. When I change to full hd with 1080p60 it's working fine. But when I change to 2160p30 in /boot/armbianEnv.txt it isn't working. Even the eth0 isn't working any more, i.e. the LEDs are not blinking and I couldn't connect to the system any more (additional to the fact that the monitor connected to hdmi is also dark). Has anybody been successful with pine64 and 4K with that image or another desktop image? Best regards, Willy P.S.: I also did the FastEthernet fix "ethtool -s e…

Hello - I have attempted an install of Armbian Stetch on a Pinebook (non HD) with the latest image from https://www.armbian.com/pinebook-a64/. I can power on the pinebook and can SSH in, and have successfully installed to the internal emmc, however the screen does not come on. This pinebook readily works with other OS images I've attempted. I suspect I'm just missing something somewhat obvious, but I can't find reference to this issue elsewhere - how do I enable access via the screen/keyboard on the device itself? Thanks!

the system does not start with emms, the red light lights up and that's it, I tried to record another version of the uboot, the armbian icon appears and the wheel spins does not respond to pressing the keys. I couldn't write the issue to the bugtracker....

I'm fairly new to Linux, so excuse me when I'm asking the obvious. I'm using ARMbian 5.25 stable Ubuntu 16.04.2 LTS 3.4.113-sun8i on a Orange Pi Zero, RTL-SDR and DireWolf When I execute from prompt: rtl_fm -f 144.80M - | direwolf -c sdr.conf -r 24000 -D 1 - Everything starts up as it should. But as I'm planning to use a headless setup, some self sustaining feature after power failure or whatnot is necessary. I figured out how to configure a cronjob and it starts a shell script when the software is not running. In that shellscript I'm using: DWCMD="bash -c 'rtl_fm -f 144.80M - | direwolf -c s…

Has anyone tried to install PiVPN or EasyRSA on a Rock64? I tried this and had some issues where EasyRSA did not install. No errors were shown on the install or captured in the install log. Took me a while to figure out that EasyRSA was not installed. It even created .opvn files for clients... I finally figured out what happened. Did some research and found a suggestion to manually install some packages BEFORE installing PiVPN. That seems to work, so now I have a working VPN. I just wanted to see if anyone else is having an issue. I will also post on the PiVPN Github site to get their input. Thanks!

I want to play video on my orange pi one (armbian jessie OS) for every 5 minutes. I use crontab -e And added */5 * * * * orangepi /usr/bin/vlc /home/orangepi/video.mp4 In the last line of file .but it isn't working ,so how can play video for every five minutes?

I would kindly like to ask you to enable the intermediate functional block, ifb, as a module in the default kernel config for the BPI-R1 CONFIG_IFB=m It should not hurt anyone as it is just a module. The ifb network device is quite useful when doing experiments with tc (trafficx control), and it is absolutely necessary when you want to affect incoming traffic (normal tc netem works only on outgoing packets) Thank you.

Please Help me How to Edit File /sys/firmware/devicetree/base/model ? ARMBIAN 5.88 user-built Ubuntu 18.04.2 LTS 5.1.0-aml-s905

I'm performing Valgrind testing on an ElPotato running Ubuntu Bionic image from Armbian. My program is dying like in https://bugs.kde.org/show_bug.cgi?id=381556 : ``` valgrind --track-origins=yes --suppressions=cryptopp.supp ./cryptest.exe v ==12969== Memcheck, a memory error detector ==12969== Copyright (C) 2002-2017, and GNU GPL'd, by Julian Seward et al. ==12969== Using Valgrind-3.13.0 and LibVEX; rerun with -h for copyright info ==12969== Command: ./cryptest.exe v ==12969== ARM64 front end: branch_etc disInstr(arm64): unhandled instruction 0xD5380000 disInstr(arm64): 1101'0101 0011'1000 0000'0000 0000'0000 ==12969== valgrind: Unrecog…

Скрытый текст Скрытый текст

Hi, I want to patch the kernel with the preempt-rt patches from the repository but their are corrupt Who needs this patch? I think the real time kernel is very useful for many projects.

As the title says, I would like to ask your help if you still keep some old working orange pi one plus image. I have downloaded some images in https://dl.armbian.com/orangepioneplus/ but none of them work with my boards. I could not SSH to the board or it says `Network error: Connection refused` As far as I know orange pi one plus H6 image OPi One Plus - 5.1.0-sunxi64 works with board. Please share your working image download links. Thank you for your help

Can someone please test this img on Orange Pi Lite. 4gb sd card or larger You can use nmtui to connect to wifi Connect to wifi the point browser to port 5000 of the IP address to see if gui starts and doesn't have any issues. http://x.x.x.x:5000 Thank you for your help. login root password octoprint Full instructions here http://www.cnx-software.com/2017/07/11/how-to-use-octoprint-on-orange-pi-lite-board-amlogic-s905x-and-s912-tv-boxes/

Hi, I was reading for some days and don't know what's is best SBC for recording (maybe orange pi plus 2e @tkaiser). Right now, I have 6 1080p IP cameras recording 5 fps 1024 kbs bit rate in a raspberry pi 2 with raspbian and a edimax 7811 wifi. 3 cameras record over ftp. 3 cameras record by shell scripts using ffmpeg only copy not transcode. I like better bandwidth and if possible hardware decode 1080p for streaming online Videos. Thank you for your time.

Dear all, I can successfully build an out-of-tree module on 5.9 and 5.10.x kernels, but have trouble running them since Armbian 20.11.6. I fixed the module.lds missing problem using the receipt from a bugreport with an extra Makefile target: PWD=$(shell pwd) VER=$(shell uname -r) KERNEL_BUILD=/lib/modules/$(VER)/build # Later if you want to package the module binary you can provide an INSTALL_ROOT # INSTALL_ROOT=/tmp/install-root MY_CFLAGS += -g -DDEBUG # for newer 5.10.x kernels with x<=4 $(KERNEL_BUILD)/scripts/module.lds: $(KERNEL_BUILD)/scripts/module.lds.S sudo sh -c "sed '$ d' $(KERNEL_BUILD)/scripts/module.lds.S > $(KERNEL_BUILD)/scri…

Hi everybody, In a project I'm working on, I've added two PCA9535 I/O expanders to use 32 additional inputs on my Nano Pi Neo. I've connected the INT line from both multiplexers to the gpio11 interrupt pin on the Nano Pi Neo, and attached to that a pull-up resistor of 10k. I've used interrupts before, but my question is how to poll both PCA9535 I/O using one interrupt? my DTS when polling one (It works!): /dts-v1/; /plugin/; / { compatible = "allwinner,sun4i-a10", "allwinner,sun7i-a20", "allwinner,sun8i-h3", "allwinner,sun50i-a64", "allwinner,sun50i-h5"; fragment@0 { /* This fragment is required only if using interrupts *…

Just got a ODroid M2 to play with an during initial benchmarking, noticed some weird results. I don't see an M2 specific forum, so @Werner, please move as necessary! Anyway, always interested in crypto throughput, and ARM64 crypto extensions have always put up some good results. So, a little weird when I saw that AES XTS performance seems decent, but CBC seems awful? user@odroidm2:~$ /sbin/cryptsetup benchmark aes-cbc 128b 178.5 MiB/s 162.7 MiB/s aes-cbc 256b 135.0 MiB/s 211.3 MiB/s aes-xts 256b 1399.5 MiB/s 1407.2 MiB/s aes-xts 512b 1186.7 MiB/s 1…

Hello all! Noticing a problem with the latest versions of armbian (I'm using the files avaliable here. In particular I was using the "bullseye_current" image however I also tried some of the files in the archive. Unfortunatly wifi dosen't seem to be quite 100% in these images -- I'm unable to connect to the internet via wifi and I'm also finding the m2 zero can barely find any wifi devices at all. I did notice these errors though; [ 8.565750] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43430-sdio for chip BCM43430/1 [ 8.588984] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43430-sdio.sinovoip,bpi-m2-zero…

Hi, We can access port usig eg. echo 1 >/sys/class/leds/green_led/brightness (or red_led) echo 1 > /sys/devices/platform/gpio_sw.0/gpio_sw/PA6/data (other ports) My question is as follows: How to access to ports using C language ? Is WiringOP (This method works ) is preferred or another method is better? #define LED 0 wiringPiSetup () ; pinMode (LED, OUTPUT) ; digitalWrite (LED, HIGH) ; // On

I run mpd on port 6680 in OPi No problem if reaching in local network (localhost:6680) Now I try to reach from internet, but verifying with http://www.yougetsignal.com/tools/open-ports/ port is still closed. I try forwarding all other port in OPi like sshd port 22 also closed I'm pretty sure I set correctly port forwarding in my router because my NAS can work with same iptables rule. It seems something wrong in OPi setting, but couldn't find out what's wrong. Anybody help? #iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (po…

Hi everybody, bought 1 to 5 port multiplier card from Ali, it's based on JMB575 chip. Is there any posibility (PM firmware) to use JMB575 with USB 3.0 to SATA 3 adapter like hardkernels JMS578. Tried with latest hardkernel JMS578 bridge firmware v173.01.00.01 it recognized only first HDD. JMB575 Link for reference https://www.aliexpress.com/item/SATA-Expansion-Card-1-to-5-Port-SATA3-0-Controller-Card-Motherboard-SATA-Multiplier-Riser-Card/32899742104.html

I installed Armbian_21.05.1_Odroidxu4_buster_legacy_4.14.222.img on HC2 and after this nextcloudpi with the actual curl script. Portsharing Port 80 and 443 in Fritz!box 7460 worked only for IPv4. An earlier installation of Armbian 14 months ago on the same machine worked under IPv4 and IPv6. It is a mystery for me. Could anyone help? http://ix.io/3nCZ Thanks