Advanced users - Development

Hi everyone, I have a problem with my Cubietruck that I was able to partly debug now, but I really like to have input from those who know more about this setup. On my Cubietruck (trusty, kernel 4.6.5-sunxi), I have a 120GB SSD (no-name brand) and added an ext4 partition and corresponding fstab line to mount it. Booting and mounting this partition works well when I cold start my system, and had powered it off before for a while. But when I do a warm start (sudo reboot), the system hangs on boot, quite reliably (it seems to occasionally work, though). I changed my kernel command line and added 'init=/bin/sh', started a 2nd bash terminal before replacing …

Good morning all, how are you?. I'm looking for help on knowing about the buffer strength on an H3 board, I've been looking on the H3 SoC datasheet and found this about GPIO's: Buffer Strength defines drive strength of the associated output buffer. but I don't know if the buffer is the entire port or not because I can't find any other reference to it and I don't want to fry the board. Can anyone explain me this?. Thanks in advance dor the help.

I'm trying to create a custom Armbian image based on the User Configurations documentation. I can see that I can install additional packages by editing `userpatches/lib.config` and adding entries to the `PACKAGE_LIST_ADDITIONAL` variable, and I can work with custom files like scripts by placing them inside `userpatches/overlay` and accessing them in `/tmp/overlay` via `customize-image.sh`. My question is, does `customize-image.sh` support the below commands given that it executes in a chroot environment: NOTE: Some commands below require `sudo`, but because we're already in a chroot environment, I assume we can run them without `sudo`. 1.…

When I reboot my Orange Pi PC 2 with my Realtek USB Dongle so the firmware is already loaded onto the Dongle I am seeing this: [ 31.659072] Bluetooth: hci0: RTL: examining hci_ver=0a hci_rev=097b lmp_ver=0a lmp_subver=ec43 [ 31.659815] Bluetooth: hci0: RTL: unknown IC info, lmp subver ec43, hci rev 097b, hci ver 000a [ 31.659830] Bluetooth: hci0: RTL: assuming no firmware upload needed [ 31.659852] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000002 [ 31.668671] Mem abort info: [ 31.671488] ESR = 0x96000004 [ 31.674561] EC = 0x25: DABT (current EL), IL = 32 bits [ 31.679880] SET = 0, FnV = 0 [ 31.682937] …

Dear gurus good afternoon. I ask for help because itself I don't understand any more what not so I do. I should make a clone of my sdcard, but nothing leaves. I tried so: I find the sdcard fdisk - l I create the empty file of an image dd if=/dev/zero of=armbian.img bs=2048 count=1402144 also I add him to loop losetup/dev/loop0 armbian.img now I clone the sdcard in loop the device dd if=/dev/sdd of=/dev/loop0 now I write down a half-scientific image on new sdcard dd bs=2048 if=armbian.img of=/dev/sdd As a result my sdcard doesn't seem on linux and I can't mount sections and loading doesn't happen to sdcard. Prompt please in what a mistake and as to me to make a clone of …

Dear Friends, this is Judy from Banana Pi team. We will have BPI-M2S and BPI-R2 PRO sample ready on May. If you have interesting and ability to develope the software for these two boards, please contact me, my mail: judyhuang@banana-pi.com Look forward to cooperate with you!

I'm just trying to create a new image for the ClearFog Pro, b/c I need some special kernel modules built-in. Compiling kernel 4.4.4 with my settings works great, but I have problems to boot the image. This is my build command: sudo ./compile.sh BRANCH=next BOARD=armada KERNEL_ONLY=no BUILD_DESKTOP=no PROGRESS_DISPLAY=plain RELEASE=jessie But u-boot complains about starting with the following message. Even the u-boot `help` command doesn't work. ... Board configuration detected:Net: | port | Interface | PHY address | |--------|-----------|--------------| | egiga0 | RGMII | 0x00 | | egiga1 | SGMII | In-Band | | egiga2 | SGMII | In-Band …

I found it very confusing that Armbian doesn't seem to follow the Ubuntu/Debian traditional scheme for naming kernel modules: linux-image-*, linux-modules-* and linux-headers-*. I need them to cross compile out-of-tree kernel module in `schroot`. Armbian seem to have only `linux-image-edge-rockchip64` and `linux-headers-edge-rockchip64`. What's the reasoning behind such design decision? Moreover, I've noticed kernel packages incorporate all the logic that make the board bootable, instead having more generic kernel binaries and relying on `flash-kernel` tool that both Ubuntu and Debian widely use. I wonder why not? What are chances in future `linux-im…

I installed the linux-image-dev-sunxi64 and linux-dtb-dev-sunxi64 packages, which pulls in the 5.1.5 kernel, and it seems something is amiss in the pinebook dtb. On the 4.19 kernel, pwm-backlight powers on, and you get video output, however, on 5.1.5 once u-boot loads the kernel and it is starting, video output goes away. In the 4.19 kernel, the kern.log shows the following output during boot: May 29 19:15:10 localhost kernel: [ 3.937999] EXT4-fs (mmcblk0p1): mounted filesystem with writeback data mode. Opts: (null) May 29 19:15:10 localhost kernel: [ 5.573863] random: lvmconfig: uninitialized urandom read (4 bytes read) May 29 19:…

Has anyone been able to get kernel 4.???? to work on an orange Pi Pc?

I would like to use a CI service to build Armbian images, ideally BitBucket pipelines since that is where most of my projects are. Has anyone had any success doing something similar? I thought it would be easy since docker based builds are supported, but it seems the supported technique is to run a command on the host that starts a separate docker container. Most CI build now are already running in a container and while I think running docker inside docker is possible, I have not been able to get that to work well in the past.

Hello I have a problem to generate my kernel 3.x and jessie for may board A10 lime. I followed the procedure well but unfortunately I always get this error message after u-objcopy boot.nin: ./scripts/dtc-versions.sh: ligne17: dtc: command not found ./scripts/dtc-versions.sh: ligne18: dtc: command not found *** Your DTC is too old, please upgrade to 1.4 or newer dtc make: *** [checkdtc] error 1 I use a VM vmware ubuntu 14.04 x86 server as recommended in the documention. (I have even try Debian Jessie and Trusty, the problem is the same) Can you help me ? Sorry for the google translation. Grégory

I am having trouble with my SPI LCD, which uses driver panel-mipi-dbi It works great when I use a minimal Armbian image, but with a desktop image it doesn't work. This is because package "plymouth" does something in the ko loading order: it loads panel-mipi-dbi too early. Plymouth provides a graphical boot animation. The driver depends on a binary file /lib/firmware/panel-mipi-dbi-spi.bin (but the file name could change depending on the DTS) At boot time, I saw that the panel-mipi-dbi.ko is loaded BEFORE the EXT4 in the microSD is mounted... and the binary file is not in the initrd.img-version (checked with lsinitramfs) …

Where are config files in source kernel with function to enable next uart port in udoo?

Building some more custom banana Pi images with the Igor repo. Tried to install plex and it seems to succeed but when finalizing the image these errors occur 0 upgraded, 1 newly installed, 0 to remove and 21 not upgraded.Need to get 109 MB of archives.After this operation, 0 B of additional disk space will be used.Get:1 http://dev2day.de/pms/wheezy/main plexmediaserver armhf 0.9.12.3.1173-937aac3-1~wheezy [109 MB]Fetched 109 MB in 1min 9s (1,567 kB/s) Selecting previously unselected package plexmediaserver.(Reading database ... 39625 files and directories currently installed.)Unpacking plexmediaserver (from .../plexmediaserver…

Linux 6.12 mainlined PREEMPT_RT, real-time preemption. As far as I understand, one no longer needs to muck about with patches, the kernel can simply be compiled for real-time use with normal compiler flags on any common architecture. This makes Linux suitable for tasks with precise latency requirements, of which there is a lot of in the embedded space. Has anyone tried this on Armbian 25.2 now that it uses the 6.12 kernel? Does it work? How would one compile Armbian with it?

I've started the job of switching both rockchip64-dev and rk3399-dev to 5.2.y ...

I am going to use your Banana Pi image for my media server image release. I would like to know how to re-enable the regenerate ssh keys and resize the SD card on first boot (I want the password to stay the same).

Mainline dev image as here: https://forum.armbian.com/index.php/topic/3574-orangepi-2-wifi-driver-issue-in-mainline-dev-410/ When I try to run armbianmonitor: rufik@opi2:~$ sudo armbianmonitor -m Stop monitoring using [ctrl]-[c] Time CPU load %cpu %sys %usr %nice %io %irq CPU/usr/bin/armbianmonitor: line 271: /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_cur_freq: No such file or directory 12:57:09: MHz 0.02 1% 0% 0% 0% 0% 0% 38.5°C^C So it looks like cpufreq not working. Dmesg says: rufik@opi2:~$ dmesg -T | grep -i cpu [Wed Feb 15 21:40:37 2017] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=50c5387d [Wed Feb 15 21:40:37 2017]…

Hi all, I'm using armbian on a cubietruck for various purposes. One of them is HAM radio. BUt I just noticed we don't have support for AX25. In fact, we're missing all HAM-related stuff, so I think it isn't possible to build just the modules: # CONFIG_HAMRADIO is not set What I would need is this: CONFIG_HAMRADIO=y # # Packet Radio protocols # CONFIG_AX25=m # # AX.25 network device drivers # CONFIG_MKISS=m # uname -a Linux cubie.acasa.local 4.3.3-sunxi #3 SMP Mon Dec 28 11:27:16 CET 2015 armv7l GNU/Linux Thanks for your support. Marius

I've started looking at switching Rockchip64-DEV to 5.0.y ... I've now my RockPro64 under 5.0.y ... It look much more easier task than the previous one with Sunxi-DEV ! @Igor , I've pushed a "rockchip64-4.20" tag that will allow to bring 4.20.y into NEXT if we wish ... Also, is there any reason why RockPro64 still using U-Boot SPL 2017.09-armbian (from Ayufan's branch) instead of Mainline U-Boot such v2019.01 ? If No, I will switch that too ...

U-boot is always a great source of amusement, did anyone try that combination? Just yesterday got v2018.05 in, and it just does not work. I don't get any serial from u-boot SPL, do I don't know what is happening. I compiled it with #define DEBUG, and still no serial output at all. At last I downloaded latest mainline u-boot (v2018.07-rc2) from github, applied manually the patches, complied and it worked. It seems something very specific for v2018.05 and rockchip/rk3288

Hi Guys, I have recently been contracted to a new project where I have moved out of my comfort zone (embedded 8-bit/32-bit uC) and have started my work on a H3 based device (currently NanoPi Neo) with Armbian. Over the course of my work I have managed to get up to speed with the basics; configuration, scripting, hardware and interfaces and device trees to a point where I can now work on the device as a proof of concept. The work that has been contributed so-far to the armbian project is impressive as is the active and knowledgeable forum - to which I hope I can contribute. One element which I cannot find an easy solution to is one of remo…

Hi, every one! have any of you guys tried to perform SPI loopback tests on any of existing boards ? I mean this driver code http://elixir.free-electrons.com/linux/v4.13.14/source/drivers/spi/spi-loopback-test.c. I tried to find any information on how to run tests but I completely failed to make it. It would be nice if someone shares a step-by-step instruction. Thanks a lot.

Hi igor Can you build and add libcsptr to your repo? ( https://github.com/Snaipe/libcsptr ) it is required by libvdpau. i tried to build it via the build environment but it doesn't work ;-) :-( vdr_sunxi-vdpau (){ git clone https://github.com/Snaipe/libcsptr.git $DEST/cache/sdcard/usr/local/src/libcsptr chroot $DEST/cache/sdcard /bin/bash -c "cd /usr/local/src/libcsptr && mkdir build && cd build && cmake -DCMAKE_INSTALL_PREFIX=/usr/local .. && make && make install" chroot $DEST/cache/sdcard /bin/bash -c "cd /usr/local/src/libcsptr && make" chroot $DEST/cache/sdcard /bin/bash -c "cd /usr/local/src/libcsptr &am…

Hi all. In response to aarch64 because the images have been distributed to the official NanoPC-T3 and NanoPC-M3 arm7l and Armbian you want to distribute. From the official not working so actively hard? http://wiki.friendlyarm.com/wiki/index.php/NanoPC-T3 https://github.com/friendlyarm/ Thanks.

Hi, after pure installation Armbian_4.5_Lamobo-r1_Debian_wheezy_3.4.109.zip, the log is full of GMAC messages: [43099.518189] GMAC TX status: VLAN frame [43099.521192] GMAC TX status: VLAN frame [43099.524646] GMAC TX status: VLAN frame [43111.775611] GMAC TX status: VLAN frame [43112.963963] GMAC TX status: VLAN frame [43112.980989] GMAC TX status: VLAN frame [43112.986370] GMAC TX status: VLAN frame [43112.989681] GMAC TX status: VLAN frame [43112.992410] GMAC TX status: VLAN frame [43112.996184] GMAC TX status: VLAN frame [43113.002038] GMAC TX status: VLAN frame [43113.973308] GMAC TX status: VLAN frame [43113.976078] GMAC TX status: VLAN frame [43114.143583] GM…

Hi, I'm using banana pi m1+ with armbian legacy kernel. I'm building an application with c sharp and using mono to run in in the banana pi. My application needs to change gpio output levels multiple times while running, so I installed bcm2835 library in the banana pi to control the output level from the application. Using the library, I was able to control those as I want, but I'd noticed that there are default gpio output levels, which are different from each gpio pins. I'm using CON3-P36 and CON3-P38. Right after the boot up, CON3-P38 goes high, while CON3-P36 goes low. I want to adjust the CON3-P38 to go low in the boot up, so that both two have low output as d…

Hi! I’ve been trying to build a kernel with custom settings for a couple of days now, but am facing some issues. My build setup is a virtual machine (running in VMWare Workstation Pro v15) based on the mini.iso image that's recommended in the Armbian documentation (and post here in the forums). The target is an Odroid N2+ SBC. There was no apparent issues setting up the build framework, installing git and cloning the repository. I then executed the compile.sh script and manually set the kernel configuration via the menuconfig interface that pops up. This however yielded an output image that, surprisingly enough, does not use my supplied configurati…

for compiling Next LTS 4.19.y images I did try to update my build-system, but I do get errors on 2 packages which I cant resolve Does anyone had this problem and could tell me how to solve this? Or would it be more easy to reinstall the build-system? The following packages will be upgraded: libc6-armhf-cross libc6-dev-armhf-cross 2 to upgrade, 0 to newly install, 0 to remove and 0 not to upgrade. Need to get 2,904 kB of archives. After this operation, 0 B of additional disk space will be used. Get:1 http://de.archive.ubuntu.com/ubuntu bionic-updates/main amd64 libc6-dev-armhf-cross all 2.27-3ubuntu1cross1.1 [1,899 kB] Get:2 http://de…

Hello, I have just installed the Armbian_23.11.0-trunk.114_Orangepi5_jammy_edge_6.6.0-rc1_xfce_desktop.img It boots OK, but does not present any desktop, but I can ssh into it and configure In syslog I find lots of errors where lightdm fails due to: Sep 20 16:10:15 orangepi5 systemd[1]: lightdm.service: Scheduled restart job, restart counter is at 4. Sep 20 16:10:15 orangepi5 lightdm[2103]: Error getting user list from org.freedesktop.Accounts: GDBus.Error:org.freedesktop.DBus.Error.ServiceUnknown: The name org.freedesktop.Accounts was not provided by any .service files Sep 20 16:10:16 orangepi5 systemd[1]: lightdm.servi…

Hi Wondering if anyone knew the algorithm that assigns mac addresses to orange zero. Is it based on something static/cpu id /...? or it is purely random. Will this mac change over time or after it is generated, it will stay the same? I have one zero that mac is pretty static and another changed mac after I did a upgrade. If I want better control of the mac address, what's the best way to make it static? this is on the mainline -jerry

Hi, running Armbian Ubuntu on Nanopi Neo2 and it is working really great. I would like to implement HPN-SSH but I can't compile any of the OpenSSH versions against OpenSSL 1.1.x present on system. Any idea if OpenSSL 1.1.x can be safely downgraded to the latest OpenSSL 1.0.x release? I would use for example the method described here Not sure if OpenSSL 1.0.x would break anything on the system or not? Thanks for your help and advise!

Hello, I've just built and installed new Armbian console image on OrangePi PC. I am trying to use the a10disp utility, first of all to get information - info command: sudo a10disp info, but it shows error "kernel sunxi disp driver does not support versioning. This program requires sunxi display driver 1.0 or higher", while dmesg shows error "disp_ioctl, line 1584:para err in disp_ioctl, cmd = 0x0,screen id = 65536". Please advise what is wrong and how to get correct result.

Hello i successful compile kernel for my chinese tablet and work but usb host no work. # modprobe g_ether modprobe: ERROR: could not insert 'g_ether': No such device I use this configuration in kernel: https://pastebin.com/gWJWtRav i use base image cubieboard 1 legacy, script.bin for A13-SOM and uboot from archlinux uboot-a13-olinuxino-2017.01-2-armv7h.pkg.tar.xz .. Work: Wifi Realtek RTL8188CUS Nand read/write sdcard Audio jack 3.5 No tested/No know: LCD no can test at broken. Touch Guddix GT811 how to test? HYM8563S Real Time Clock (I2C). how to test? MMA7660FC 1.5 g 3-Axis Accelerometer (I2C…

Are the rtl8814au drivers updated? I did a custom build and the custom drivers seem to get 25% more throughput. I did a make from this guide Edimax guide: How to install EW-7833UAC in Linux running kernel higher than v4.4 The driver has updates for: {USB_DEVICE(USB_VENDER_ID_REALTEK, 0x8813),.driver_info = RTL8814A}, {USB_DEVICE(0x2001, 0x331a), .driver_info = RTL8814A}, /* D-Link - D-Link */ {USB_DEVICE(0x0b05, 0x1817), .driver_info = RTL8814A}, /* ASUS - ASUSTeK */ {USB_DEVICE(0x0b05, 0x1852), .driver_info = RTL8814A}, /* ASUS - ASUSTeK */ {USB_DEVICE(0x0b05, 0x1853), .driver_info = RTL8814A}, /* ASUS - ASUSTeK */ {USB_DEVICE(0x056E, 0…

Aside from the DNS resolution issue I am having (different thread), I am often getting stuck on the following: Unpacking locales (from .../locales_2.13-38+deb7u8_all.deb) ... Processing triggers for man-db ... Setting up locales (2.13-38+deb7u8) ... Generating locales (this might take a while)... Generation complete. Generating locales (this might take a while)... en_US.UTF-8... done Generation complete.​ It just sits there and nothing further happens. I have left it for 30 minutes or more, and still nothing. I usually end up killing it... rebooting and then restarting. When it does get past this, I typically end up with the debian sources DNS resolution is…

On Black Hat 2017 security researcher Nitay Artenstein showed a vulnerability affecting millions of smartphones he called BroadPwn. The bug/vulnerability sits inside the firmware blobs but I didn't pay that much attention since I thought it would be related to recent smartphones and at least the one I use still receives full security fix support now in the 5th year. But when I heard that latest Raspbian release contains a fix for BroadPwn (RPi 3 and Zero W use BCM43438 to provide wireless capabilities) I asked myself immediately a question: http://www.cnx-software.com/2017/08/17/raspbian-for-raspberry-pi-boards-gets-upgraded-to-debian-stretch/#comment-545270 …

Currently I am busy getting the new version of Kerberosio video surveillance software (website) to work on Armbian (Debian Jessie). The current version is already working (refer also to this post), and I have also compiled successfully the most recent development version which includes video recording which is not included in the current release. There will be a special Armbian page (I am currently writing it) on the Kerberos.io site in the near future. I am working towards a general Armbian recipe. Because the software originally focuses on the Raspberry Pi Platform, there are some slight differences (library dependencies because of the Raspberry Pi camera which is s…

Hi, I managed to make w1-GPIO work in Orange Pi Zero v3 for, for example, the DS18B20 sensor. However, I have some doubts about setting the GPIO flags for w1-gpio. Many examples provide flags in the form gpios = <&pio 0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; but in the dts file when I use this form it does not work (syntax error) so I have to provide the flags in digital form. A description of flags and bits is here https://elixir.bootlin.com/linux/v6.6.30/source/include/dt-bindings/gpio/gpio.h If I would like to set GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN then the digital value for…

Hello! I'm trying to build xunlong kernel from https://github.com/orangepi-xunlong/linux-orangepi/tree/orange-pi-5.10-rk3399. I see a .dts file for OrangePi 4 ... but no suitable defconfig or any description what defconfig to use. What I'm doing wrong?

Build on new kernel (5.1), Ubuntu 18.04. No cpufreq information (0 MHz in htop etc.) also means there's no working frequency scaling. Which for Allwinner H2+ (Banana Pi M2 Zero) means quick hard-hang due to overheating whenever I compile anything non trivial, unless I point a USB Fan on the CPU (which already got a heatsink). Is there any chance of getting cpufreq and dvfs to work?

Hi Igor, I'm trying to build and update the kernel for the Lime2 board using the script you provided on github. I'm using linux sunxi 3.4.103. The only changes i've made in the kernel are in the sunxi-codec.c file, where i'm changing the values to some variables which should impact the latency on voip softphones. Here are the changes that i'm doing in "static struct snd_pcm_hardware sunxi_pcm_playback_hardware" and "static struct snd_pcm_hardware sunxi_pcm_capture_hardware" { - .period_bytes_min = 1024*4 + .period_bytes_min = 16*2 - .periods_min = 4 + .periods_min = 2 } The problem is that after running the script i get the tar file with 5…

I'm attempt to do two simple switches via GPIO on OrangePi R1 LTS Plus using RK3328 using .Net Core and here my code snippet. GpioController ioc = new GpioController(PinNumberingScheme.Logical, new RockchipDriver(gpioRegisterAddresses: new uint[] { 0xFF21_0000, 0xFF22_0000, 0xFF23_0000, 0xFF24_0000 })); int iPin=RockchipDriver.MapPinNumber(???) // where do I find the information to do logical pin number mapping? ioc.OpenPin(iPin); ioc.SetPinMode(iPin, PinMode.InputPullUp); PinValue v=ioc.Read(iPin); Thanks for reading and any suggestion is appreciated.

For some time there is NAND driver for both SPL and u-boot for Allwinner SoCs. You can check boards/sunxi/README.nand. I'm currently testing this. What I'm thinking is, if this option works fine, should nand-sata-install script to be reworked? Instead of using the old SDK u-boot, mainline spl+u-boot to be packed in the bootloader deb and then written somehow? At this point as I can see only CHIP_pro has this feature enabled.

Hi all, I have a bananapi and I have installed the debian Wheezy image with kernel 3.19.0. Now, I’d like to upgrade to kernel 4.0.4 to see wether the ananlog audio output is supported; so I downloaded all the deb packages from the website and installed them, but after reboot the system is still using kernel 3.19.0. How can I switch it to use kernel 4.0.4? I guess I should edit something in boot.cmd and convert it to boot.scr, but what should I change exactly? Thanks in advance for your help!

Hi all, please be aware that Pine folks in the meantime understood that recommendations to use WinDisk32Imager, dd and other non verifying burning tools are wrong, tried to recommend Etcher instead (as usual sabotaged by at least their most famous forum moderator) and now use finally a 'branded' Etcher 2.0 beta: https://forum.pine64.org/showthread.php?tid=4481&pid=27520#pid27520 I don't think it's correct to do it this way (and at least the macOS application sucks since not digitally signed and using a wrong so called 'bundle identifier') but anyway. Let's take this for a foresight. Etcher 2.0 uses catalog files in such a way: http:…

I am trying to get NanoPi Neo to work with a Murata 2AE module Over USB. The Murata module uses the Infineon CYW4373 chipset. So far I have: Rebuilt the kernel with CONFIG_BRCMFMAC_USB=y. This allowed the device to be recognized, but unable to load a driver Installed linux-firmware. Now the devices loads and even shows up as a wireless interface in ifconfig (wlan0 on bleeding edge, wlx..... on current) However, configuring the interface or scanning does not work. root@nanopineo:~# iwlist wlan0 scan wlan0 Interface doesn't support scanning : Invalid argument and I can find the following errors in dmesg: …

Hi there, i want to stick to the 4.4 kernel an tried to compile kernel 4.4.12 (cubietruck) via: apt-get -y install git git clone https://github.com/igorpecovnik/lib--depth 1 cp lib/compile.sh . chmod +x compile.sh ./compile.sh after that, i built the following directory and file: mkdir userpatches vi userpatches/lib.config and added: KERNELBRANCH="v4.4.12" (also tried KERNELBRANCH="v4.5.6") as described here: http://forum.armbian...est-kernel-447/ Whenn running ./compile, i get the following messages: │ LD [M] drivers/media/v4l2-core/tuner.o …

Armbian provides its own hostapd. Why? This is relevant because of the recent WPA2 bug. Upstream hostapd has been patched: https://packages.debian.org/jessie/hostapd I don't understand the precise relation between Debian and Armbian. Will this patch percolate down? Thanks

Hello everyone, I am new to this forum. Apologize if this has been asked before, but I couldn't find it. I do docker run -it -P --privileged lib /root/compile.sh I get the following towards the end of the build process Fetched 68.1 MB in 60s (1,130 kB/s) Reading package lists... Reading package lists... Building dependency tree... Reading state information... hostapd is already the newest version (2:2.6-4~armbian5.34.171017+1). The following NEW packages will be installed: sunxi-tools 0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded. Need to get 36.9 kB of archives. After this operation, 134 kB of additional disk …

Discussion thread for github issue 423 - glshim packaging. Related discussion is here. Glshim development happens here. Current status: build script is mostly working, I'm fixing minor issues before making a github commit: - avoid hardcoded dependencies - make sure OpenGL apps can be built on target system Once these are resolved, I'll post a link to my commit for an eventual review and will be ready to create a pull request. ---------- Unrelated topic: armbian build script fixes for Debian Jessie Although only Ubuntu distribution is supported by armbian build scripts, Debian sid and above have all the necessary packages and should work fine. For Debian Je…

Hi! I recently managed to boot Armbian on the QuartzPro64 board (RK3588) from Pine64. I also installed Proxmox, which worked out of the box. This is really amazing to me! To do this, I manually replaced the kernel and DTB file from the Armbian image for the OrangePi5 board, since it's based on the same CPU. Now, I would like to build the image for the QuartzPro64 using the Armbian build script. So far, I've already : added a new .conf file in config/boards (based on orangepi5-plus.conf) added a new .config file in config/kernel added a new entry in the list of branch in config/sources/families/rockchip-rk3588.conf. …

Hello, I would like to use armbian on a custom board with an arm processor. I' am a beginner and I don't know many things about o.s and board. My questions regards what issues will I have to face? Why I can't just install it like i do with desktop? Why I need to customize it? What things I need to customize? Is O.S customization an "easy" job or it will take months? What are the advantages of starting with armbian instead of starting from ubuntu (xenial)? What are the critical component of a board (what need customization)? Thanks in advance.

Hi, I am having some trouble to compile the kernel after I have made some minor changes to one of the source files. to minimize recompilation of unchanged code files I chose the following settings in compile.sh: KERNEL_ONLY="yes" SOURCE_COMPILE="yes" KERNEL_CONFIGURE="no" KERNEL_CLEAN="no" to avoid having my changes overwitten by the original files I set FORCE_CHECKOUT="no" # igre manual changes to source I am afraid I have not managed to recompile the kernel using these settings. What happens instead is: (1) the script still tries to sync with the source but produces some error messages: error: Your local ch…

Hello, I was trying to add the module em28xx (PCTV 460e DVB S2 drivers) but get errors Cubietruck Vanilla 2.81 What I did: 1. make menuconfig in /usr/src/linux-headers-4.3.3-sunxi 2. add Device Drivers -> Multimedia support -> Media USB Adapters -> Empia EM28xx USB devices support -> DVB/ATSC Support for em28xx based TV cards as Module 3. "make scripts" as there was an error with the scripts 4. make modules I get the following error Is there a tutorial how to build additional modules on the cubietruck ? Could you include the module in future releases ( iirc the S2 adapter works with the legacy image out of the box so the d…

Perhaps I badly searched, but except for the file makeboarddeb.sh not find the option how you can make changes to the initrd. Perhaps there is some primitive or correct functionality that may make changes in the collected initrd, which gets in the finished image. I need to add some utilities and modify init in the initrd. Возможно Ñ Ð¿Ð»Ð¾Ñ…Ð¾ иÑкал, но кроме файла makeboarddeb.sh не нахожу варианта, как можно внеÑти Ñвои Ð¸Ð·Ð¼ÐµÐ½ÐµÐ½Ð¸Ñ Ð² initrd. Возможно еÑÑ‚ÑŒ како-либо правильный функционал, который может вноÑить Ð¸Ð·Ð¼ÐµÐ½ÐµÐ½Ð¸Ñ Ð² Ñобира…

Hello all, I have something that you might find useful. I created an image for the Ubuntu 16.04 core for the firefly roc-rk3328-cc board. I followed the firefly docs to compile the firefly 4.4.114 kernel and build out the u-boot image. I followed this guide http://docs.khadas.com/social/BuildUbuntuRootfsViaUbuntuBase/ to get the ubuntu rootfs. I then created a disk image with the u-boot kernel, ubunutu rootfs, and the SoC. It actually worked. This is a very minimal install to the point where I have to modify the rootfs guide above to include the eth0 interface and probably install the network-manager. …

hello, i try to update my armbian and i got this E: Release file for http://security.debian.org/dists/bookworm-security/InRelease is not valid yet (invalid for another 2d 3h 4min 26s). Updates for this repository will not be applied. E: Release file for http://deb.debian.org/debian/dists/bookworm-updates/InRelease is not valid yet (invalid for another 2d 2h 59min 29s). Updates for this repository will not be applied. E: Release file for http://deb.debian.org/debian/dists/bookworm-backports/InRelease is not valid yet (invalid for another 2d 2h 59min 29s). Updates for this repository will not be applied. E: Release file for http://apt.armbian.com/dists/bookworm/InRe…

SEC mode being set for legacy and mainline. Overriding u-boot default of non-sec I've got a patch to make it conditional. just doing a bit more testing cooresponding github issue: https://github.com/igorpecovnik/lib/issues/408 pull request: https://github.com/igorpecovnik/lib/pull/409

We are starting a HW design for a board that will probably be using RK3328. We want this board to be running Armbian. We need to select BT and Wifi chips. Would like to use chips that are already supported by Armbian. Is there a list of Bluetooth and Wifi chips that Armbian supports? Any recommendations?

Hi all, I'd like to compile latest kernel 4.11-rc7, so i added KERNELTAG="v4.11-rc7" to ./compile.sh and created file /userpatches/lib.config and added KERNELBRANCH="4.11" to it i also added to /lib/configuration.sh according to documentation ARMBIAN_MAINLINE_KERNEL_VERSION='4.11' # lock in a particular kernel version but i get this error : [ o.k. ] Using user configuration override [ userpatches/lib.config ] [ o.k. ] Syncing clock [ host ] [ o.k. ] Downloading sources [ o.k. ] Checking git sources [ u-boot v2017.03 ] [ .... ] Up to date [ error ] ERROR in function fetch_from_repo [ general.sh:184 ] [ error ] Error in configuration [ o.k. ] Pr…

Dear Community, Currently Im playin with my Banana Pi M2 Berry and therefore I need a fusion of the LATEST Armbian -System with the compilers needed by the Boards Offical "GPIO-Libarys", which are outdated 7years ago. The most important libary would be the RPi.GPIO. RPi.GPIO The problem is, that this libary was using python2 and python3, python2 isnt my future i think, but for compiling the lib with python3 I need some pip-packages and the right arm-gcc compiler = 4.8 i think. DO i may need a cross-compile libary or whats are the requirements to build the lib on the latest system? To avoid hardware-d…

I just got a copy of the dev branch armbian comipled (2017-04-10). I'm here with the grand goal of getting libsurvive running with the HTC Vive on the Orange Pi. In order to do this, I need to coax the OrangePi to output to the vive. I was skeptical at first, but it appears you guys support 4k@30, so it should be okay on the pixel-clock front. The vive is 2160x1200@90Hz. You can't underclock it. Just won't go then. It's sadly the only mode the thing supports. I've seen shreds and bits here and there of information about how to do this, but, it seems that most of it is out-of-date for the "dev" branch. Any hints on how I can get the OrangePi to output as per …

I was adding a driver to mvebu64-default and when this patch is removed, compilations breaks this way: Spoiler drivers/net/wireless/rtl8814au/core/rtw_mp.c: In function ‘rtfloor’: drivers/net/wireless/rtl8814au/core/rtw_mp.c:36:12: error: ‘-mgeneral-regs-only’ is incompatible with floating-point argument static int rtfloor(float x) { ^~~~~~~ scripts/Makefile.build:269: recipe for target 'drivers/net/wireless/rtl8814au/core/rtw_mp.o' failed make[4]: *** [drivers/net/wireless/rtl8814au/core/rtw_mp.o] Error 1 scripts/Makefile.build:476: recipe for target 'drivers/net/wireless/rtl8814au' failed make[3]: *** [drivers/net/wireless/rtl8814au] Er…

A great 9.30 min review here, pointing out the issues: Cooling, GPIO expansion, no MIPI, lack of SPI support in Armbian? https://m.youtube.com/watch?v=MzxLYGWQddA Apparently the much discussed Armbian cooling/Vreg techniques were not known to the author. Other stuff is interesting, with comparison to RPi.

Hi, first of all thank you for the great work. Let me tell you my story. I bought a Pinebook laptop some months ago and in my spare time I was playing with numerous OS-es. Installing and testing one by one. In total I've tested every single OS and so far Armbian is the winner. Why? Well because it is super fast, very stable, lightweight and with very simple xfce desktop look and feel. Now, like everything in life, there are some bad sides of Armbian. I am not sure if I will say something false or strange but I don't consider my self expert for hardware nor Linux world. So far I have also Raspberry Pi with Raspbian installed and don't see any bad si…

For anyone who wants a minimal "network-install" like image for orangepizero. Does this with the customize-image.sh and armbian build scripts. Could be cleaner but would be much easier to just hack the build scripts. I've tested with jessie and stretch, and with branches default, next, and dev. The image should boot up, get eth0 dhcp address, and have serial console on ttyS0. Script option to remove systemd and use sysvinit. Might be modded to work with other boards? Set the following options and use the customize-image.sh. If script breaks due to upstream changes, use last tested commit: git checkout -f a66121 # required options f…

I'm just starting out with Armbian development, and the most recent "stable" version (5.20, v2016.09) doesn't compile. Is this supposed to work? olaf@tackd:~$ mkdir routertest olaf@tackd:~$ cd routertest/ olaf@tackd:~/routertest$ olaf@tackd:~/routertest$ git clone -b v2016.09 https://github.com/igorpecovnik/lib Cloning into 'lib'... remote: Counting objects: 19756, done. remote: Compressing objects: 100% (155/155), done. remote: Total 19756 (delta 75), reused 0 (delta 0), pack-reused 19601 Receiving objects: 100% (19756/19756), 173.96 MiB | 1003.00 KiB/s, done. Resolving deltas: 100% (12762/12762), done. Checking connectivity... done. Note: checking out '4c5…

Hi there, I have this device left over from a previous project, and now I want to repurpose it for a forked version of PiKVM that is meant for alternate SBC such as the OrangePi. I spent the last 2 days adjusting various build settings and compiling. After installing, the kvmd service would complain about the UDC driver missing. Also executing ls /sys/class/udc/ would return nothing, seemingly indicating that OTG is not possible. Just last night I came across the file "sun50i-h6-orangepi-3-lts.dts" in which there is a comment containing the following: /* * This board doesn't have a controllable VBUS even though it * does hav…

Hello, In december, it was possible to install 4.19 kernel for Rock64. Unfortunately this kernel was removed from Armbian repo. 4.20 kernel is bogus, USB doesn't work and SD card is very slow. 4.19 was fine. Is it possible to make it available again in in the repo ? Thank you

Hi guys, do you have idea why boot stopped? Check log below please. It was build about 25minutes ago but about 1 week younger build was working. U-Boot SPL 2017.03-armbian (Apr 03 2017 - 19:48:42) DRAM: 256 MiB Trying to boot from MMC1 U-Boot 2017.03-armbian (Apr 03 2017 - 19:48:42 +0100) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi Zero DRAM: 256 MiB MMC: SUNXI SD/MMC: 0 *** Warning - bad CRC, using default environment Setting up a 720x576i composite-pal console (overscan 32x20) Error: no valid bmp image at 66000000 In: serial Out: vga Err: vga Net: phy interface0 eth…

This may be a somewhat stupid question, but I just cannot find anything about it. I have custom-compiled the kernel for Allwinner A20/cubietruck as described here on a Virtual Box Ubuntu 18.04 Once done, I took the *.deb files out of output/debs, copied it to the machine and installed them. Everything worked fine and so far so good . But the "build" directory on the host with the compile.sh script is surprisingly empty. However, if I want to cross compile an additional kernel module on the virtual machine, how do I set this up? Is it enough to "make" with CROSS-COMPILE=arm-linux-gnueabihf-? or do I also need to somehow consider the linaro stuff in c…

Thanks for the great armbian work this community does! I am trying to use an Espressobin board as a Homeassistant host. However I am struggeling with the usbserial of the kernel. Here is what I get with the Linux 4.19.59-mvebu64 kernel when I plug in the SiliconLabs based HubZ zigbee USBstick: [ 159.552682] usb 1-1: USB disconnect, device number 2 [ 164.277522] usb 1-1: new high-speed USB device number 3 using orion-ehci [ 164.436750] usb 1-1: config 1 interface 0 altsetting 0 bulk endpoint 0x81 has invalid maxpacket 64 [ 164.436792] usb 1-1: config 1 interface 0 altsetting 0 bulk endpoint 0x1 has invalid maxpacket 64 [ 164.436828] usb 1-1: config 1 …

Hello there, I'm new to this Forum, so please I been trying to run Kodi as standalone music station with Buster minimal and Kodi 17 on it. This system boots very quick and I've been quite happy when I got kodi starting successfully, but it's very slow. It takes several seconds to switch from one menu item to the next. Next I tried to speed up the graphics using this instructions https://forum.armbian.com/topic/1420-opengl-on-mali-gpu-bananapi-orangepi-pc-etc/ http://wiki.lemaker.org/BananaPro/Pi:GPU But failed with xorg saying: /etc/X11/xorg.conf: There is no /dev/mali, /dev/ump or /dev/disp device available. …

Hi All, I have looked at the "How to build your own image/kernel post", but am wondering what the best way for me is to contribute. Basically, I often use the pine64 running armbian as an IoT control hub/gateway where it is running an install of nginx/php/mysql/mosquito/nodered. The php part is mostly because of phpmyadmin, so nginx comes in that case configured with node-red mounted on / and phpmyadmin on /phpmyadmin. I could create my own image with all this stuff on it, and also configure some default usernames, passwords and wifi setup, but I also noticed the "Software" section in armbian-config. So my question is which of these 3 options would b…

Hello, I wanted to know if there was a mean, a special technique to test the latest version of armbian on x86_64 architechture. I tried with qemu but I get error messages apparently due to the size of the sectors.

I have been playing around the Rock Pi S from radxa, and am stumbling at enabling the I2S output using a device tree overlay. (Building using current Armbain that uses @piter75's kernel branch) As per the data sheet and pinout, `i2s_8ch_0` should be broken out to the GPIO, but I don't seem to be getting far enabling it via the device tree. Any inputs? This is what I am playing around with atm, but `dmesg` doesn't show anything helpful atm, and no "I2S-Card" device turns up. Tried disabling the inbuilt audio codec ( connected to `i2s_8ch_2`), but still no dice. The closest example I could find was from `rk3308-ai-va-v10.dts`, that similarly enables the `i2s_8…

Hello, how i can change this message: I checked /etc/motd but is empty. Regards

Just a minor problem: uptime from procps-nf 3.3.15 (Armbian buster) - as used in 30-armbian-sysinfo to get uptime/logged-in users/load - generates different outputs if the uptime is either less or more than 1 day or less than 1 hour ("hh:mm" or "d days, hh:mm" or "nn min") - this gets the 30-armbian-sysinfo confused on gathering the logged-in user count resp. load. I suggest the below fix: ... # get uptime, logged in users and load # fix for uptime from procps-ng 3.3.15: reports uptime less then a day as "hh:mm," # but uptime larger than a day as "nn days, hh:mm," or "nn days, mm min", and less than 1 hour as "mm min," # which mixes up the assig…

Can someone tell me how to enable PWM in cubieboard2. I am using the latest ubuntu of armbian and vanilla kernel from this link. http://www.armbian.com/cubieboard-2/ Looking at /sys/class, I cant find any pwm folder root@cubieboard2:/sys/class# ls ata_device gpio iscsi_iface power_supply scsi_host ata_link graphics iscsi_session ppp spidev ata_port hwmon iscsi_transport pps spi_master backlight i2c-adapter leds ptp thermal bdi i2c-dev mdio_bus …

Hi to everyone! I've just bought an orange pi pc+, and i've seen that the script that should install armbian into mmc is not working for me. The script only write the rootfs, but I am not able to see uboot and MLO. In past i've used proto-Board like BeagleBone. So the question is, how the script works? is there any way to compile MLO?

Hi all, has anyone ever tried to use an atomic firmware upgrade system like rauc or swupdate? https://rauc.readthedocs.io/en/latest/ https://sbabic.github.io/swupdate/swupdate.html I am playing with rauc, in order to do that I have to customize the partitioning of the SD/eMMC: - root1 (4GB) - root2 (4GB) - data (8GB, or remaining space) Can someone suggest how to customize partitioning in such way? I played around setting USE_HOOK_FOR_PARTITION=yes, and hooking the create_partition_table but had no luck. Any hint? Thanks in advance! Andrea

Hi, I own a Orange PI One and I wanted to create a compile environment in a virtualbox as I did not find any available. So I followed the instructions found here: http://www.armbian.com/using-armbian-tools/ 1) downloaded "ubuntu-14.04.4-server-amd64.iso" 2) create a new virtual box image (ubuntu 64bit) 3) Execute the following command: apt-get -y -qq install git git clone --depth 1 https://github.com/igorpecovnik/lib cp lib/compile.sh . sudo ./compile.sh The process end with the following lines: [ o.k. ] Building deb [ linux-u-boot-orangepih3-5.07-armhf.deb ] [ error ] ERROR in function compilte_uboot [ common.sh:155 ] [ error ] Building u-b…

Hello All, Does someone knows a possible reason why AXP 209 on some boards are failing? That will result to an error message "Failed to set core voltage! Can't set CPU frequency". After that we cannot probe the i2c bus address of the AXP209 anymore. Hope someone can share some insights. U-Boot SPL 2015.10-rc5-gc387326-dirty (May 19 2016 - 19:02:38) DRAM: 1024 MiB Failed to set core voltage! Can't set CPU frequency Card did not respond to voltage select! …

I've struggled the whole day on that task using v2019.01 ... It is even worst than my struggling back in early December, even using Method #2 give me headache with Pinctrl not initialize and boot device been garbage : channel 0 training pass! channel 1 training pass! change freq to 800MHz 1,0 ch 0 ddrconfig = 0x101, ddrsize = 0x20 ch 1 ddrconfig = 0x101, ddrsize = 0x20 pmugrf_os_reg[2] = 0x3281F281, stride = 0x9 OUT U-Boot SPL board init Pinctrl init failed: -19 Trying to boot from m�iYk~Ⱥ�C��+J)H�^J!������wZ��q�+����q����!

In recent armbian for orangepi-pc (Fossil 5.8.y) I encountered /dev/video0 and /dev/video1 I disabled both video and csi devices in dtb, but /dev/video0 and /dev/video1 did not disappear. Same happened with serial ports also. In dtb file 4 serial ports are described. Only one port is enabled, but /dev/ ttyS* contains 8 serial devices /proc/device-tree/soc/serial* directory contains exact number of serial ports as it is described in dtb. does anybody have an experience in disabling devices via device tree? Or the devices are hardcoded in the kernel?

Since update to 5.5.0 kernel (-rc2) my Orange PI often freezed after uptime of several hours up to 3 days (usually less than 24 hours). Since downgrade to 5.4.10 it seems to be stable again (1 day for now, so I still keep my fingers crossed). (Before upgrade to 5.5. it was up for several weeks - and I don't remember any unplanned reboot). Unfortunately I have no logs (it logs to ram), but in one case if was connected via ssh and had "htop" running - it showed nothing special at freeze time (CPU temperature around 50°C, no high load (around 0,5 load avg, only one CPU cure with a CPU % > 50% (still < 80%)). When I noticed the frozen system, I n…

Was wondering if there are any kernel update scripts i can use to update from http://mirror.igorpecovnik.com/kernel/ http://mirror.igorpecovnik.com/u-boot/ would be nice im open to colab on a script if there isn't any

I'm having trouble trying to do a custom kernel configuration using this image on my hc4. It's just not opening menuconfig, I get the screen to select the board ( odroid hc4), then the LTS/Edge kernel screen, then this is the only output: ~/build$ ./compile.sh BOARD=odroidhc4 BRANCH=current BUILD_MINIMAL=no BUILD_DESKTOP=no KERNEL_ONLY=yes KERNEL_CONFIGURE=yes COMPRESS_OUTPUTIMAGE=sha,img [🌿] Applying cmdline param [ 'BUILD_MINIMAL': '(empty)' --> 'no' early ] [🌿] Applying cmdline param [ 'COMPRESS_OUTPUTIMAGE': '(empty)' --> 'sha,img' early ] [🌿] Applying cmdline param [ 'BUILD_DESKTOP': '(empty)' --> 'no' early ] [🌿] Applying cmdline param […

Hi, Please have a look at the list of supported devices by a patching framework https://github.com/seemoo-lab/nexmon Mostly bcm43430a1 devices, I believe patch should also be suitable for AP6212 WiFi chip, as it's patches only or mostly mac driver ? (Not an expert here). Patches apply smoothly on RPi3. Would be really nice to have this functional on Friendly ARM NanoPi Neo Air.

I already saw similar posts on this here, here and here. It looks like the combination of Kernel and Kernel-Header 5.89.190617 again is not complete to build own modules. Based on the configure script: Then I tried to check the headers: Since it was already a few times on the forum and sometime there was a new build created and it was fixed again, I would like to know if I just came over the same error again or if I did something wrong. cheers, Daniel

You may have read about the recent (one month ago, but hey, what's a month between friends?) security vulnerabilities discovered in dnsmasq. They have been patched in version 2.78 and, quoting the author: This is a bugfix release, and, amongst other things, addresses a set of serious security vulnerabilities. Update should be mandatory. The dnsmasq shipped with Armbian is a rather old 2.75 and it is enabled by default, so I see this as a rather significant risk. I have compiled the latest version and installed it by hand, following the instructions located here (obviously, with 2.78 instead of 2.76). Is there any chance of getting this package updated in …

Hello, when I try apt update, I got this message: W: Failed to fetch http://apt.armbian.com/dists/jessie/InRelease Unable to find expected entry 'main/binary-i386/Packages' in Release file (Wrong sources.list entry or malformed file) My /etc/apt/sources.list.d: deb http://apt.armbian.com jessie main jessie-utils jessie-desktop Is any error on my side or how to correct this please? Thanx

Hi I think the subject I am interested in, called Kiosk OS or computer. I like to build a computer that when you turn it on, it does only execute one or some programs that I want. how can I do that? Is it a simple thing or should I spend weeks or months to learning and doing that? (I am a newbie linux user but know the C language). Very thank you in advanced!

We developed so called Cloud images, which are a combination of minimal images + kernel with minimal set of drivers. Images also doesn't have any firmware packages, so bare OS comes down to 700Mb. Build from sources: ./compile.sh \ BETA=no \ BOARD=uefi-x86 \ BRANCH=cloud \ BUILD_DESKTOP=no \ BUILD_MINIMAL=yes \ ENABLE_EXTENSIONS=image-output-qcow2 \ IMAGE_VERSION=25.2.3 \ RELEASE=noble \ VENDOR="Company" \ VENDORCOLOR="5;100;115" \ KERNEL_CONFIGURE=no \ KERNEL_BTF=yes Customization: https://docs.armbian.com/Developer-Guide_Overview/ Details in promo style: Spoiler Very Fast Boot Time: Optimi…

I posted a git issue for the Banana Pi image that the mainline kernel wasn't working with OpenMediaVault (at the time I think it was 3.19.3 or .4). It is now working with mainline 3.19.7 so all is resolved. Will release an openmediavault image when I find the time

Sometimes I get in trouble building a new image. This could be caused by a variety of reasons, e.g an Armbian patch does not work with the latest kernel, a new u-boot version makes trouble or some functionality is broken in the image like the USB and v4.6.1. stuff here: http://forum.armbian.com/index.php/topic/1338-a20-lamobo-r1-kernel-461-usb-issue/ How could I step back to working Armbian main build libraries and a working kernel and stay on both? Will this work? cd lib/ git checkout 2a2e190 # commit form June 1, 2a2e190: Move up to 5.14 since we need to ... cd .. touch .ignore_changes echo "KERNELBRANCH=\"v4.5.6\"" > userpatches/lib.config # add # KERNELT…

Hi to all Armbian Devs, According to my local experience done today with newly Ayufan's 4.20.0 tag done this morning, it seems to be quite ready ... (Except for my failure to get eMMC running on RockPro64, but works well on OPi-RK3399 and NanoPC-T4) So, I'm asking you if I should commit all those stuff !!! @TonyMac32 during those builds, I see 2 patches broken, I didn't investigated, but maybe those patches are simply not relevant anymore and can be deleted : [ warn ] * [l][c] renegade-add-uhs.patch [ failed ] [ warn ] * [l][c] rk3328-add-GRF-GPIO.patch [ failed ] One my side, I need to fix some patches to…

Hello. I have troubles with the new version from source. The main reason i compile it from source, instead of downloading pre-build images is to enable CMA in kernel config. And now i try to apply some patches like in this last post - Kodi/XBMC on Armbian with hw Accleration possible? . The version i try is CLI Armbian_5.07_Lamobo-r1_Debian_jessie_3.4.111. First there are some errors at the very beginning, then first boot is freezing at recreating SSH keys and after long time some messages for disconnecting and reconnecting USB devices appears and that's all, no reboot. I thought those patches are the problem and try without them, same condition. I have builded image from…