Allwinner sunxi

Gent's currently I run Igor's Debian Image on a BananaPi (kernel 3.4.105). I want to add the wifi driver for Ralink_RT5527. What is to do? Here my thoughts, - install header's - pull sunxi-kernel - copy config from running kernel - make menuconfig - add the driver - make correct ? Regards

I've set up my new OPi Zero as a wireless AP running the latest Armbian build for the OPi0. It's working mostly great. My one problem I'm having is that my speeds seem to be throttled to 5-6Mbps. I connect wirelessly from my phone and run a speed test and get 5-6Mbps. If I connect directly to my router, I get 30Mbps. I have a Rpi3 set up about the same as the OPi0, and when I connect it up I get the full 30. Each time I've tested with the OPi and RPi, my phone is the only device connected. So, I've poked around online and I can't seem to figure out if it's a hardware limitation or if it's a software/driver/setting limitation. Also, if it's the latter, how/where to…

As stated in the topic the new Orange Pi Zero LTS reports incorrect system temps (likely due to 16bit overflow if I were to guess): ~$ cat /sys/devices/virtual/thermal/thermal_zone0/temp -2178 Model Purchased: https://www.aliexpress.com/item/4000070093365.html

I got my lite days ago, and have tried lots of images, none of them can recognize the build-in wifi Instead, a eth0 device is presented. is it the actual wlan? Armbian gives me the best compatibility so far (in terms of usb support) I can read the chip module is printed realtek 8189FTV, but lsmod shows me a 8189es module loaded. By google around, no luck for the FTV version driver. I also played with the script.bin, but still no luck. Anyone can give me some hints. Thanks.

- A64 - strange naming "win"

Hi, I am trying to make the OPI Zero boot with the help of the onboard SPI with the goal to boot from an usb drive and not from the sdcard. What steps should be executed. I only managed to get the Xenial image to work with my 512Mb board... so that is what I want to use. I assume... I need to make u-boot work with the sdcard... move the whole thing to the usb drive (with the u-boot) and than populate somehow the SPI with the image of an SPL, which would get it up through the u-boot on the usb. So I would need some in depth guidance (best would be some example commands to be used), what steps and tools should be executed to make it work. Thanks in advance &amp…

Hi there, I am a new user of OPi PC+, downloaded, flashed Armbian_5.20_Orangepipcplus_Debian_jessie_3.4.112_desktop.img basic setup OK, got IP, changed passwords etc, GUI starts. As I don't have USB keyboard/mouse, I've opened SSH session, then set export DISPLAY=laptop2:0 , then xterm. OK. From BT side it also looks ok: adapter blinks, I can find my BT keyboard/mouse using hcitool scan Now the problem: if I launch bluetooth-applet / bluetooth-assistant it CRASHES (assistant) at step of PAIRING device. (applet still alive). So my quiestion is, how to pair this remote device without "assistant", and make it available as "normal" keyboard/mouse? [device …

that steps must be followed to install kodi in armbian? thnks I have added 'deb http://http.debian.net/debianjessie-backports main' in sources.list and sudo apt-get update & sudo apt-get install kodi but when you start kodi the screen goes black

Well it took me longer than i hoped but i have managed to forward port icenowys code for TVE on the H2+/H3 to mainline armbian. It seems to work totally fine, with a few caveats. First: Sample images of it in action -> https://imgur.com/a/vXQEM Second: the patch itself -> https://github.com/stevenj/h3-tve/tree/v0.0.11 Third a prebuilt image for Orange Pi Zero: -> https://github.com/stevenj/h3-tve/releases/tag/v0.0.11 Howto: just put the patch into userpatches for the sunxi-next kernel, and build. it should apply cleanly. Its for H2+/H3. I have only tried it on a orange pi zero, but it should work on all H2+/H3 boards. …

Hi, we bought several Lime2 and tested them. Unfortunatelly, the GBit-Lan did not seem to work reliyable. Later ping tests revealed a packet loss on many boards of 1% to 20%. (eg. "ping -s 9000 -i 0.0001 -c 5000 fritz.box"). Some boards dont have any problems, other more. On heavy access with SSD it's increasing a little. It's happens also without SSD. Other boards worked fine at the same power and network cable. Its possible thant this strange TX_DELAY isn't set correctly? Are there other problems known? I used the wheezy image with kernel 3.4.105-lime2 and 3.4.107 from you latest wheezy image. The image with Kernal 4.0.4 stopped after "restarting sshd",…

Hi, after successfully booting the "Armbian_5.69_Orangepizeroplus2-h5_Ubuntu_bionic_next_4.19.13.img" image from a SD-card I decided to use "armbian-config" to copy/install Armbian to the onboard eMMC. The operation finished without an error but the devices now hangs/loops on boot. I've a TTL UART so here is the output: U-Boot SPL 2018.05-armbian (Jan 09 2019 - 22:59:13 +0100) DRAM: 512 MiB Trying to boot from MMC1 NOTICE: BL31: v2.0(debug):a9f803b NOTICE: BL31: Built : 20:16:26, Jan 7 2019 NOTICE: BL31: Detected Allwinner H5 SoC (1718) NOTICE: BL31: Found U-Boot DTB at 0x407ecc8, model: OrangePi Zero Plus2 INFO: ARM GICv2 driver initialized…

Hey, after making sure that all packages are current (armbianmobitor upload available at http://sprunge.us/Migh)I still have the problem currently that my three cubietruicks freeze after working 1-3 days. Mostly they are still ping-able, but no "heartbeat led blinking" happens anymore and SSH connect also not possible. The logs simply say nothing. Is there anything knows with uboot 5.23 in case ob unstability? The last uboot I remember that was quite stable was 5.20 ... Can I simply downgrade to that using sudo apt-get install linux-u-boot-cubietruck-next=5.20 or such? Thanks for an advice... Ingo Fischer

I Installed the Armbian system who is dedicated for my OPI version: http://www.armbian.com/orange-pi-pc/ with instruction, formatted SD card with format size adjustment option ON. But when I want to boot it there is only still green light (steady all time). OPI not giving any boot information on screen. This issue is not caused by SD card becasue I tried two (which one is recommended): Kingston 32GB (class 10) and Samsung EVO+ 32GB. Has anyone had similar experience or have any idea how to solve this?

Hey I followed the instructions on this page: https://kaspars.net/blog/linux/spi-display-orange-pi-zero But I can't get my 3.5" TFT Touchscreen work: https://aliexpress.com/item/3-5-3-5-Zoll-TFT-LCD-Touchscreen-320x480-SPI-RGB-Display-Board-F-r-Raspberry/32834124804.html I’ve got an Orange Pi Zero with armbian (ubuntu with legacy kernel). I only see the backlight LED is working (white screen). On kaspars blog everything looks so easy. I hope someone can help me with my problem. Thank you in advance guys!

Hello :D! Im new customer of Orangepi board. My board: ORANGE PI PC. I have a question, some one have a guide or have try to create a script for make a button ON - OFF on GPIO on this board? I have try with ETA PRIME GUIDE FOR RASPBERRY PI 3 (u can find on youtube) but this guide is for raspberry pi 3, and dont work on orange pi. I have install this GPIO for orange pi from this guide : http://www.instructables.com/id/Orange-Pi-One-Python-GPIO-basic/?fref=gc I need really to put button on gpio and make on off board from here, very tnx at all!

I have just received cheap WiFi dongle (paid $1.6 in Aliexpress). I don't know yet if I will solder it directly to Orange Pi One extra USB exposed solder points. Currently I want to share how to disassemble this dongle without damaging anything. Watch my short tutorial video: Using this module without the case significantly improves WiFi signal quality and range. Finally it would be possible to solder external antenna socket. Some photos:

Hi Is docker supposed to run on OrangePi PC with Armbian 5.11? How about DM Thin below? BR Anders anders@orangepi1:~/bin$ sudo systemctl -l status docker â— docker.service - Docker Application Container Engine Loaded: loaded (/lib/systemd/system/docker.service; enabled) Active: failed (Result: exit-code) since Fri 2016-06-03 17:48:47 CEST; 14min ago Docs: https://docs.docker.com Process: 571 ExecStart=/usr/bin/docker daemon -H fd:// (code=exited, status=1/FAILURE) Main PID: 571 (code=exited, status=1/FAILURE) Jun 03 17:48:44 orangepi1 systemd[1]: Starting Docker Application Container Engine... Jun 03 17:48:46 orangepi1 docker[571…

Hi, I am new to Orange Pi, Armbian and this forum. Done lots of Raspberry Pi and other Linux stuff. Can someone tell me if the Orange Pi Zero Plus 2 H3 & H5 boards are supported by armbian? They are available on Aliexpress here(H3) and here(H5). They are not listed on the download page, but are listed in this post. Also, if they are supported, is it better choosing the H3 or H5 variant? Seems to me like the H3 might have better software support, and might be the better choice.

Hello, I have a OPI zero, I want to use it as access point, but when I start hostapd appears this message: root@orangepizero:~# hostapd /etc/hostapd/hostapd.conf -dd random: Trying to read entropy from /dev/random Configuration file: /etc/hostapd/hostapd.conf nl80211: Could not add multicast membership for vendor events: -2 (No such file or directory) rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0 nl80211: Supported cipher 00-0f-ac:1 nl80211: Supported cipher 00-0f-ac:5 nl80211: Supported cipher 00-0f-ac:2 nl80211: Supported cipher 00-0f-ac:4 nl80211: Using driver-based off-channel TX nl80211: Supports Probe Response offload in AP mode nl80211: Use separate P2P …

Hi, I have bought Orange Pi Zero and installed Armbian Ubuntu version. Device (and OS!) works fantastic. However, I have a problem, because DNS resolving does not work until I manually edit /etc/resolv.conf file and enter: nameserver <ip_of_my_router> The problem is, I am using my Zero device in different networks, so I need to reconfigure it every time I connect it to other network. Is there any solution for this? In fact, it is quite weird, I have tried several things (when DNS resolving was not working), for instance: dig @8.8.8.8 www.slo-tech.com any and got only: ; <<>> DiG 9.10.3-P4-Ubuntu <<>> @8.8.8.8 www.sl…

Hello guys, i'm trying to connect that ili9341 display with my m2 zero but it wont work. My armbian Version: Armbian_23-02-0-trunk_Bananapim2zero_lunar_edge_6.1.11_xfce_desktop The display has a pinout that matches with the raspberry pi, so also the banana pi m2 zero would do the job, since it has the same pinout like the raspberry pi has. It uses 26 pins to connect to the banana pi m2 zero gpio output pins. 3 buttons and a touch panel are available but i only want to use the lcd for now. I edited the armbianEnv.txt to open the spi port and added my overlay tft.dts to /boot/overlay-user but i cant get a picture on the screen, Its just glowing …

on a Sunvell R69 (H2) and a NanoPi Neo (H3) I got these "old known" eth0 Link Up/Down syndrom, but couldnt find a solution in the forum while using the search-engine armbianmonitor -u System diagnosis information will now be uploaded to Sunvell R69 - Linux sunvell-r69 5.4.0-rc8-sunxi #19.11.3 SMP Wed Nov 27 17:01:29 CET 2019 armv7l armv7l armv7l GNU/Linux : http://ix.io/232T NanoPi Neo - Linux npi-neo 5.3.3-sunxi #5.98 SMP Sat Oct 5 18:34:15 +03 2019 armv7l GNU/Linux : http://ix.io/232U in dmesg it looks like [10536.264427] dwmac-sun8i 1c30000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [10568.008…

Hi does install to emmc works for orange pi plus 2 h3 board? I will be getting my plus 2 soon so want to know is it supported in arbian jessie yet. Regards, -- Avinash G A

Hi, i am running armbian stretch on an OrangePi PC with "-dev" kernel and uboot. This was originally an jessie installation with legacy kernel, that was upgraded. I'm wondering now, why the cpu frequency only scales between 648 and 1008 MHz instead of 408 and 1296 MHz. Is this to be expected? cpufrequtils is configured to the latter. # lscpu Architecture: armv7l Byte Order: Little Endian CPU(s): 4 On-line CPU(s) list: 0-3 Thread(s) per core: 1 Core(s) per socket: 4 Socket(s): 1 Model: 5 Model name: ARMv7 Processor rev 5 (v7l) CPU max MHz: 1008,0000 CPU min MHz: …

Edit: Please see my second post in this thread. I think I've identified exactly what my problem is, please see my second post in the thread. I need to change the display mode to something that my own TV is able to display. But no matter what I've tried, I haven't been able to change the display mode. How do you do it? ---- Hello, I just got an Orange Pi PC. I installed using the Armbian_5.32.170629_Orangepipc_Ubuntu_xenial_dev_4.11.7.7z image. I'm able to log in through SSH, and I've installed all updates (apt-get update && apt-get upgrade) I have the Orange Pi PC connected to my HDMI television. The scre…

Hello Igor! Please help. What am I doing wrong? My device: LeMaker BananaPiPro (black board with yellow GPIO). http://www.armbian.com/banana-pi-pro/ Your build: Debian jessie Legacy Kernel 3.4.109 uname -a Linux bananapi 3.4.109-banana #5 SMP PREEMPT Wed Sep 30 14:20:25 CEST 2015 armv7l GNU/Linux I need the following: 1. Install light gui (i were install xfce4 (+goodies) + lightdm) 2. Internet browser (i use iceweasel) 3. On-line film and serials from internet 4. Sound from HDMI (bananapipro connect to my tv) The items 1, 2 and 4 - No problem. The item 3 - Very poor quality video. What has been done: http://linux-sunxi.org/Mali_binary_driver http://wiki.lemaker.or…

I tested the recently added sunxi-dev patch to improve the SATA write speed. Here are the results: Board: Cubietruck OS: Ubuntu Bionic (18.04.2), Armbian 5.86 Kernel: 5.1.0 with and without RFC-drivers-ata-ahci_sunxi-Increased-SATA-AHCI-DMA-TX-RX-FIFOs.patch SATA-device: SAMSUNG SSD 830 Series, 256GB Measurement method: dd if=/dev/zero of=/tesfile bs=? count=? oflag=direct bs: measured 4k, 64k and 1M block sizes count: adjusted to ensure that data written is ~500MB Measurements below are made with kernel 5.1.0 without (before) and with the mentioned patch: dd bs Before MB/s After MB/s Increase 4k 13.3 …

Hi all, I was just wondering if you had experience with the performance on the H3 allwinner CPU performance based on the cpu temperature ? I'm trying to tweak my fan to only cool down the CPU once it gets close to peak cpu temperature levels, before performance starts to degrade. According to the Allwinner H3 datasheet the maximum ambient operating temperature is 70° (see page 612) http://dl.linux-sunxi.org/H3/Allwinner_H3_Datasheet_V1.0.pdf Do you think I can let the cpu go up to 70 before cooling it down or should I start sooner (i.e 65° / 67°) to keep my pi at top performance ?

Hello, I liked to have fixed MAC address to my Orange Pi lite. At the moment, after every boot I have different one. First of all, is there "real" MAC for this board? If there is, how the see it? Then what would be correct way to set static MAC, U-boot/Scribt.bin/ifconfig...? I am running Armbian 5.14 Jessie server.

Hi, I got one of those cheap 300Mbps wifi dongles with 8192EU chip with USB Vid/Pid 0bda:818b. How can we enable this in Armbian? lsmod does not show any detected h/w driver and wan0 is not showing up in ifconfig. Only lsusb has the following root@nanopineo:~# lsusb Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 0bda:818b Realtek Semiconductor Corp. Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b…

@ag123, @c0rnelius, and anyone else that has interest in sound on these devices. I have been able to put together a patch that enables audio for H161/H618 devices. So far only audio on HDMI works. Analog audio is still generating an error on startup. The patches were taken from a git repository by warpme: https://github.com/warpme/minimyth2/tree/master/script/kernel/linux-6.6/files , and probably came from the Zunlong SDK. A lot of the code was written by Allwinner. @pixdrift generated a version of the patches for Armbian and I continued to work on them. I have a git repository if anyone would like to test, partic…

Is anyone else having issues getting incoming ssh to work with their OPI zero? I've tried both: Armbian_5.24_Orangepizero_Debian_jessie_3.4.113.img and Armbian_5.24_Orangepizero_Ubuntu_xenial_3.4.113.img In both cases I was able to get a WiFi connection, and am able to get out to the internet to download new packages (apt-get). However, I can't seem to get incoming ssh or ping to work. It's as if the device is invisible.

I'm using a NanoPi Neo as Homegear gateway. This requires the SPI interface (/dev/spidev0.0). Yesterday I ran apt-get upgrade, which bumped my kernel from 5.10.60 to 5.15.25. No other changes have been done, Since then no SPI devices are created anymore and the gateway fails! I tried to downgrade the kernel already using armbian-config to 21.08 5.10.60-sunxi. But that reported an error (do not remember the text; was very late) and left the Nano unbootable. I could restore the 5.15.25 kernel by manually editing the zImage symbolic link in /boot. Using param_spidev_spi_bus=1 instead of 0 does not help. …

Hello everyone and thank you for wonderful work on Armbian. i was wondering if anyone has any experiences to share on booting orange pi pc over network, i know it's possible to do this using Raspberry pi, but what's the latest status on Orange PI PC? is there a u-boot build capable of doing so? is this even possible?

As we know, the PCIe on H6 is buggy, which doesn't offer linear address, and Linux cannot support such kind of configuration. However, the Cortex-A53 cores used by H6 supports virtualization, which can be used to change the order of the address space. Recently, I tried to make use of virtualization to provide linear mapping of PCIe, and I succeed in making an Intel 6205 wireless card working. The hypervisor code is at https://github.com/Icenowy/aw-el2-barebone . It's intended to start before U-Boot, and located at 0x40010000. A U-Boot fork that is patched to load the hypervisor is at https://github.com/Icenowy/u-boot/tree/h6…

I would like to add the Orange Pi Lite 2 into the discussion of boards to support. Info from Orange Pi site - http://www.orangepi.org/Orange Pi Lite 2/ Hardware specification CPU H6 Quad-core 64-bit ARM Cortex™-A53 GPU • High-performance multi-core GPU Mali T720 • OpenGL ES3.1/3.0/2.0/1.1 • Microsoft DirectX 11 FL9_3 • ASTC(Adaptive Scalable Texture Compression) • Floating point operation greater than 70 GFLOPS Memory (SDRAM) 1GB LPDDR3 (shared with GPU) Onboard Storage TF card (Max. 32GB) /MMC card slot WIFI+BT AP6255, IEEE 802.11 AC/bb/g/n, BT4.1 Audio Input MIC Aud…

Hi everybody I'm using Orange PI One with OS Armbian Debian GNU/Linux 8 (jessie) 3.4.112-sun8i (Server) I need to convert some videos for make video stream(H264) but it works so slowy(3~10 fps) when I use ffmpeg. I think ffmpeg works slowly because it doesn't use HW Codec so how can I enable it in H3 CPU and use it in ffmpeg?

I am working on a new project which uses the Banana Pi to capture USB output destined for a printer in order to log the output from a system. The BananaPi will need to be a simple plugin which sits between the machine and a connected USB printer - so we want to: a ) Mimic the connected USB printer (so that the machine thinks it still has the original printer attached) b ) Capture the output from the machine c ) Send the captured output onwards to the printer. The BananaPi seemed the obvious choice as it has the built in USB OTG port and we would use the gadget printer to mimic the attached printer. Unfortunately, the Bananian images do not support the gadget printer a…

Hello; My OrangePi PC HDMI port is dead, it throws no input signal, and I've read that this board has no ESD protection for HDMI, so I assume it died because of it. What I want to get is video working through analog TV out, but I can't seem to find the solution for this. I guess it should be simple task, but I never did it before. Hopefuly somebody can give me the solution. Thanks!

Got Orange Pi Plus 2 and LCD 5"monitor Waveshare. Use armbian OS 5.14 on Debian Jessie 3.4.112. All good with 800x480 resolution, but still cant use touchscreen. Will be happy if you help me with it: Monitor got interface 1, 17 3.3V Power positive (3.3V power input) 2, 4 5V Power positive (5V power input) 3, 5, 7, 8, 10, 11, 12, 13, 15, 16, 18, 24 NC NC 6, 9, 14, 20, 25 GND Ground 19 TP_SI SPI data input of Touch Panel 21 TP_SO SPI data output of Touch Panel 22 TP_IRQ Touch Panel interrupt, low level while the Touch Panel detects touching 23 TP_SCK SPI clock of T…

I have a headless Orange pi 3 and wanted to be able to test a new install. Is it possible to issue a specific reboot command that will switch to boot from one storage to the other storage? I have armbian bionic installed and running on the EMMC. and A new bionic build installed on a new SD card. So, if i'm tinkering with the new build on the SD card, can i reboot to the EMMC without removing the SD card, and then similarly reboot from the EMMC into the SD card build??

Hi I tried several image but cannot boot..it is compatible for orange pi PC ? my target is BTSync. thanks

I have some servo motor I would like to start but cannot find any info on how to do it. Is PWM available in Pi PC or Pi Zero? Thanks

boot and stopped on mount something.

Hi I need to set static IP in eth0 and wlan0 in my OPi Zero using ARMBIAN Jessie. Googling around, I read a lot of controversial options, like edit /etc/network/interfaces and use nmtui, but, I couldn't set BOTH eth0 and wlan0 to a static IP. If I do it for eth0, wlan0 doesn't work and vice-versa. One guy said that after Debian Jessie version (https://nebulousthinking.wordpress.com/2016/02/25/setting-a-static-ip-for-raspbian-jessie-in-2016/), some things changed to set up static IP. Now, from Jessie, we need to edit /etc/ dhcpcd.conf, but, where is it ( dhcpcd.conf )? Can someone instruct me about how to set static IP, please? Sergio

I am trying to get a DS18B20 working on an OrangePi zero running Armbian. The DS18B20 has a pull-up resistor and works on a Raspberry Pi, and is connected to PA10, +5V and Gnd. I have modified /etc/modules-load.d/modules.conf thus: g_serial w1-sunxi w1-gpio w1-therm I have modified /etc/default/cpufrequtils thus: ENABLE=true MIN_SPEED=480000 MAX_SPEED=1200000 GOVERNOR=interactive After a reboot, dmesg looks like this: [ 8.970765] g_serial gadget: Gadget Serial v2.4 [ 8.970777] g_serial gadget: g_serial ready [ 8.995601] Driver for 1-wire Dallas network protocol. [ 9.083869] EXT4-fs (mmcblk0p1): re-mounted. Opts: commit=600,error…

Hi, I recently read from github testings of orange pi lite2 testing that wireless is working. But I download from the official website of https://dl.armbian.com/orangepilite2/Debian_stretch_dev_nightly.7z(built 0824) and burn it, it starts, but the wireless is missing. I also read that the firmware added ap6255 wireless driver, so I download https://beta.armbian.com/pool/main/a/armbian-firmware-full/armbian-firmware-full_5.59.180915_all.deb and installed it. After reboot, the wireless is still missing. So the support of wireless is built-in or usb? Should I build armbian myself with the lastest code to support the built-in wireless? Thank you.

Hi, i discovered and solved incompatible gc2035 driver with some v4l2 applications. I made some modifications to the 3.4.39-02 kernel-lobo: gc2035: of 8fps to ~20fps eand improvements in the matter of light. The original driver accepts only 800×600, added the following resolutions: 800×600/640×480/320×240 sunxi_wdt: builtin to module (greater flexibility to change the module options) / pr_info some functions, causing flood in kern.log (switched to pr_debug) CONFIG_CMDLINE=â€earlyprintk=ttyS0,115200 loglevel=5 initcall_debug=0 console=ttyS0,115200 console=tty0 fsck.mode=force fsck.repair=yes init=/init ipv6.disable=1 kernel size: ~59mb For more informa…

due to systemd updates to a new version, maybe it's not compact with old kernel. after system upgrade, it fails to start sshd. after read code, insystemd-tmpfile chase_symlinks() return -EBADF from kernel, I guess legacy kernel not compact with newer systemd.

Hi all! Kinda "mayday-mayday" I recently upgraded Armbian to 5.35 and after reboot it gone. After long investigation i figured out, that it boots ONLY when HDMI cable connected to even standby tv. This is my home server and it works nonstop in headless mode.. I am on kernel 4.13.16-sunxi, rootfs on sata SSD. I guess something cannot be detected with uboot. How can I fix this ?

compiled https://github.com/armbian/build debian. uname -a Linux orangepipc 4.14.73-sunxi # 1 SMP Mon Oct 1 11:55:35 +04 2018 armv7l GNU / Linux apt update apt-get install -y build-essential linux-headers -uname -r` Reading package lists ... Done Building dependency tree Reading state information ... Done E: Unable to locate package linux-headers-4.14.73-sunxi E: Could not find any package by glob 'linux-headers-4.14.73-sunxi' E: Could not find any package by regex 'linux-headers-4.14.73-sunxi' what is the problem??? PS: the problem decided.

Let me start to express my gratitude for the wealth of information and software which is available here. I'm a longtime user of a usb 2.0 soundcard along with a laptop with KXStudio and Guitarix. I've used this setup many times for gigging and home recording and it proved to be stable. One of the downsides is the "voluminous" laptop. I've my soundcard mounted in a small 19" flightcase with one rack still open. For some years I've been thinking of making rack mountable effectprocessor from a board to substitute the laptop. So, to start this journey I've ordered a OPi PC (along with a good quality micro SD card!), of course not a heavyweight board, but my first…

I just upgraded (using a fresh image with the 5.69 image) one of my SOPINE A64 modules from Armbian Xenial - legacy kernel 3.10.y to Armbian Bionic - mainline kernel 4.19.y. The onboard ethernet will no longer work. The sopine module is connected to a clusterboard instead of a sopine baseboard, but the NIC is on the module so it should not make a difference. On Xenial 3.10.y kernel the driver loaded for the NIC is the sunxi_geth driver, on bionic 4.19.y kernel it is the st_mac100 driver. Here is the output of the lshw for 4.19.y *-network:0 description: Ethernet interface physical id: 6 logical name: eth0 seria…

Hi, From months i'm using the raspberry boards to monitor, control, log and to sending commands to remote stations. I've fighted against wifi devices that stop to work untill i've tried the raspberry pi3 and the edimax dongles, correct the sd errors (untill i've decided to run the boards with a readonly fs), installed the (software) watchdog, etc... but now everything works perfectly from months on more then 20 boards equipped with good power supply and sd. The last months i've tried to replace the raspberry pi board, with the orange pi lite board and armbian jessie 5.20 server. With the old version of orange pi pc, connected by ethernet, everything works fine, but wi…

I started using armbian just a few days ago, I used the cb2 image. When I updated from 5.10 to 5.11 when I play a video, the video surface is darker, for example, instead of white I get grey. Just to be sure I put armbian 5.10 in another SD and videos played well, them update to armbian 5.11 and had the same problem with video playback. Does someone have any idea what is the problem? Until the problem is solved, how can I downgrade my armbian 5.11 to 5.10? Thanks. EDIT: I downloaded and installed the 5.10 pkgs: armbian-hostapd_5.10_armhf.deb linux-firmware-image-sun7i_5.10_armhf.deb linux-headers-sun7i_5.10_armhf.deb linux-image-sun7i_5.10_arm…

Hi, i'm working on a hdmi cec driver for H3 and i'm looking for some feedback how the driver works. I have tested the driver with OrangePi PC and a Samsung TV. I have pushed my driver to github : https://github.com/jodamm/linux/tree/sun8i or here is a patch file that can be placed in userpatches for armbian toolchain. The driver can be loaded with modprobe hdmi_cec . I have modified libcec to work with this driver : https://github.com/jodamm/libcec or again a patch file for libcec.

Hiya, I'm attempting to use Wifi on the Banana Pi M1Plus board, supposed to be a Banana Pro clone from SinoVoip, but I cannot get the wifi module working with the latest Armbian 4.5, Jessie kernel 3.4.109. I have already linked script.bin to the /boot/bin/bananapro.bin file I try loading the ap6210 module and it gives errors. root@bananapi:~# modprobe ap6210 <3>[ap6210] parse wifi_used failed in script.fex. <3>[ap6210] bluetooth is disable in script.fex. <3>[ap6210] [dhd_module_init] get wl_host_wake gpio failed modprobe: ERROR: could not insert 'ap6210': Operation not permitted Thankyou for any help Lemonzest

Hello, I have been struggling for some time with random freezes. I am running application with i2c0 Fram and UART1 for transferring/receiving data based on MAX3232. The freezes cause no response from Orange PI (debug UART too), only unplug power helps. I read that it may be a problem with powering but i tried many USB power adapters 2A, 3A and ATX power (28A) connected to GND and 5v, nothing helps. I have lowered cpu max frequency to 816Mhz and still the same. All necessary data uploaded via armbianmonitor.

hi all . i found good URL https://gist.github.com/xsukax/77c627d7274736408314 aptitude install git yasm pkg-config , and then follow the URL , then i get ffmpeg . ---------------- regards .

It seems that the latest Nano Pi Neo Air Boards and the relatively new Orange Pi Zero Plus 2 both use a modified version of the AP6212 WiFi+Bluetooth module, which is physically labelled as AP6212A. This new module apparently requires different drivers to operate. From my own experience, I was unable to get the internal WiFi module to work on a Nano Pi Neo Air (with AP6212A) using any of the Armbian distributions. However, I was able to get WiFi to work on that board with the Friendly Arm distribution at from https://www.mediafire.com/folder/sr5d0qpz774cs/NanoPi-NEO_Air#oc15bwqbuxgxe. I just received a second Nano Pi Neo Air from a different vendor, and this …

I've just started using armbian yesterday and one of the first things that i'm trying to do is use my cheap USB wireless module. The chipset is the RTL8188, but the armbian originally recognised and loaded the RTL8192eu driver. When trying to connect with 8192 driver it always returned "Bad Password". Changing the /etc/modules-load.d/modules.conf to 8188cus initially seemed to work, but on the validation stage itsimply freezed and automatically rebooted, repeating it for as many times as i tried. I've also test with others like 8192eu/8192cus/8188eu/8188cu and all of then either returned no wireless network found or freeze and reboot. Is there any way to solve th…

Firstly many thanks to all the hard work from the Armbian developers - it installed onto the eMMC of my new Orange Pi Plus2E first time with no problems I'm trying to benchmark the board (with a fan/heatsink) and without. The standard Armbian runs it at a maximum of 1.296GHz but I'd like to run it faster. I'm new to using fex, but this appears to push it up to 1.536GHz with a Vdd of 1.5V: cd bin2fex /boot/bin/orangepiplus2e.bin orangepiplus2e.heatsink.fex sed -i "s/1296000/1536000/g; s/1320/1500/" orangepiplus2e.heatsink.fex cp /etc/default/cpufrequtils /etc/default/cpufrequtils~ sed -i "s/1296000/1536000/" /etc/default/cpufrequtils fex2bin orangepiplus2e.heatsink.…

When I run pygame for any significant length of time on legacy kernel it crashes with a kernel timeout error. I haven't been able to get past this, and from what I tell, it should be fixed in later kernels. So, I'm trying my hand with the mainline kernel, and I have two hurdles I haven't been able to pass yet. I'm using an Orange Pi Zero, hardware Ethernet, mainline distro, with a 2.4" SPI TFT LCD. Frame buffer is /dev/fb0 created with modprobe fbtft_device custom name=fb_ili9341 gpios=reset:1,dc:0,led:3 speed=48000000 rotate=90 busnum=0 txbuflen=65536 Whenever I create a display I get an error that it cannot open mouse. The following…

I want to use my GPIO pins on my OPi lite. After much research and testing, I have done the following - Add user pi to group gpio - Changed /etc/udev/rules.d/99-gpio.rules to SUBSYSTEM=="gpio*", PROGRAM="/bin/sh -c '\ chown -R root:gpio /sys/class/gpio && chmod -R 770 /sys/class/gpio;\ chown -R root:gpio /sys/devices/platform/soc/1c20800.pinctrl/gpiochip0/gpio && chmod -R 770 /sys/devices/platform/soc/1c20800.pinctrl/gpiochip0/gpio;?\ '"???? Now, accessing GPIO pins is working fine via bash: (env) pi@orangepilite:~$ echo 65 > /sys/class/gpio/export (env) pi@orangepilite:~$ echo out > /sys/class/gpio/gpio65/direction …

I have a problem similar to post http://forum.armbian.com/index.php/topic/182-freezing-problems-with-bpi-r1/:my board is blocked for the second time. But my configuration is quite different from that post: Kernel: linux-image-next-sunxi 4.3 (version 4.2.0-sunxi) UBoot: linux-image-next-sunxi 4.3 (2015.07) RootFS: on sda1 powered by the board (WDC WD10JFCX-68N) UpTime: about 10 days before my last restart. When the board is blocked I can't interact with the debug console on the serial port. I cant't find anything interesting in /var/log, but I'm not really an expert.

I'm trying to get a HDMI LCD touchscreen working. The pinout is compatible with Orange PI PC except the SPI CS pin is on pin 26 (WPI 11) instead of pin 24 (WPI 10). Is there an easy way to move the SPI CS pin to another GPIO pin? Also, I'm not sure how to properly configure the pen down interrupt pin for pin 22 (WPI 6) So far, I've got the following working: Image: Orangepipc_2.0.8_debian_buster_desktop_linux5.4.65.7z Touchscreen: 3.5 Inch HD HDMI USB LCD Touch Screen 3.5" Display Module 480×320 1920x1080 for Raspberry Pi 3rd 4th Generation 4B/3B+/3B/2B orangepiEnv.txt: overlays=spi-add-cs1 spi-spidev param_spidev_spi_bus=0 para…

Hello, I'm trying to have the onboard bluetooth working with OrangePi PC+ (to evaluate OPPC+ to deploy it in school with open source OS and software cf. https://forum.armbian.com/index.php?/topic/4929-which-card-choose-to-deploy-an-educational-open-source-os-in-schools/&tab=comments#comment-40408 ). I'm using the ubuntu desktop legacy version that we can download on https://www.armbian.com/orange-pi-pc-plus/ Here is the result of armbianmonitor -u : http://sprunge.us/WeEO If I'm running bluetooth in command line I have this problem : La connexion à BlueZ a échoué (The connexion to BlueZ failed) Le démon Bluez …

Hi, just a quick sanity check - is install to eMMC on pinebook known to be working (with recent Armbian images from the wip section), and is nand-sata-install the right way to do it? It just occurred to me that I might be spinning my wheels trying to figure out something that just isn't ready yet Thanks, James

Good day. I've purchased lcd 5'inch LCD. I have some troubles with HDMI connection (no image), but i fixed it using this topic: link. (drivers at disk doesnt take any effect) But i can not run touchpad. I used different hints but god no effect board - Orange Pi PC Plus kernel 3.4.113-sun8i module ads7846.ko at /lib/modules/3.4.113-sun8i/kernel/drivers/input/touchscreen My script bin: Spoiler [spi0] spi_used = 1 spi_cs_bitmap = 1 spi_mosi = port:PC00<3><default><default><default> spi_miso = port:PC01<3><default><default><default> spi_sclk = port:PC02<3&g…

Edit: Price seems to be $17.99 Just FYI: FriendlyARM is preparing another H3 board: NanoPi Air somehow related to NanoPI NEO (same low default DRAM clockspeed let me believe this). What we already know (by looking at Github commits): onboard eMMC (no idea about the size) no HDMI no Ethernet AP6212 based WiFi+BT (connected through SDIO and UART) Personal assumptions: most probably also just a single bank DRAM configuration most probably also a SD card slot maybe eMMC only an option and a basic version without eMMC available same 40 x 40 mm dimensions as NEO, eMMC on the lower PCB side next to H3, AP6212 on the upper (where the Ethernet Jack is located on the NEO -- a…

Today I swapped my old Neo2 against a Neo2 LTS 1GB in my NAS case - so I had a old Neo2 512MB free for the black Aluminum-OLED-case which I got in a drawer. Now I did try to activate the OLED in ARMBIAN 5.67 user-built Debian GNU/Linux 9 (stretch) 4.19.4-sunxi64 Linux npi-neo2-27 4.19.4-sunxi64 #6 SMP Fri Nov 30 14:02:43 +03 2018 aarch64 GNU/Linux First (like on a i2c-clock" I activated i2c0 in armbian-config: root@npi-neo2-27(192.168.6.27):~# armbian-config System --> Hardware --> [*] i2c0 After the reboot I checked for the i2c-OLED-device and got: root@npi-neo2-27(192.168.6.27):~# apt install i2c-tools root@npi-neo2-27(…

Hi, I have a new Orange Pi+ 2 and I was trying to write armbian image from: http://www.armbian.com/orange-pi-plus-2/(legacy build) but I couldn't make it work. Steps that I follow on Windows 10: - Download 7z file from armbian - Uncompress - Quick format SanDisk 32GB with SDFormatter - Write .raw file with Rufus 2.0.1 (stable). All preferences by default. - Insert micro SD to Orange Pi+ 2 - Connect HDMI, keyboard and power supply. - Green LED lights continuously. Why?? When the green LED was on, nothing happens. I had tried to install the official .img builds and just works. Why I couldn't with armbian bui…

Thought this might be useful: FROM: http://www.orangepi.org/orangepibbsen/forum.php?mod=viewthread&tid=2236 01 3.3V 02 5V 03 TWI0-SDA PA12 04 5V 05 TWI0-SCK PA11 06 GND 07 PWM1 PA06 08 UART1_TX PG06 09 GND 10 UART1_RX PG07 11 UART2_RX PA01 12 SIM_CLK/PA_EINT7 PA07 13 UART2_TX PA00 14 GND 15 UART2_CTS PA03 16 TWI1-SDA PA19 17 3.3V 18 TWI1-SCK PA18 19 SPI1_MOSI PA15 …

I've been using an OrangePi Zero hw rev. 1.5 for a few months with no issues, using the Stretch mainline image (4.x kernel). Suddenly the filesystem became read-only. I thought it was a SD card issue so I burned a fresh armbian to a new card. But the device does not show up in the DHCP pool with an allocated IP. Being withought a HDMI connector, an OPi Zero must be accessed via SSH. I've tried all versions, mainline and legacy. Only with Jessie legacy image, it gets an IP from the DHCP pool just on the very first boot. After that, it does not show up. I've tried the images provided by OrangePI and their Ubuntu and Raspbian images work. They have Ub…

Hello I have a BPi-R1 with Igor's 3.2 image (http://www.igorpecovnik.com/2014/09/07/banana-pi-debian-sd-image/) that runs as a router (with pppoe) and nginx/php5/mysql config for my wife's blog and also with ez-ipupdate for dynamic dns I have a nasty issue... once every 2 or 3 days, my board freezes for no aparent reason It does this even if root is on SD card (only sd card connected) or HDD (I have a modified mSATA adapter to get power from 3,3V SATA power connector... I removed the 3,3V regulator and added a thick wire from the 3,3V provided by the board through the SATA connector) Also I moved from this configuration: to this fan gpio controlled (witch was ver…

Hi guys I am having some issues with booting from emmc created a sdcard with th latest armbian version for the orange pi pc plus can boot it without problems updated and upgraded everything. then ran nand-sata-install all seems to be going ok but after that it wont boot from emmc without sd card inserted I am pretty sure I am missing something obvious lol any help with be greatly appreciated

Funnily with Zero Plus 2 a silent downgrade to H3 happened (I would assume that's related to Xunlong's software guy Buddy not being able to resolve voltage regulation issues with Allwinner's BSP and H5): http://www.cnx-software.com/2017/03/17/18-9-orange-pi-zero-plus-2-board-allwinner-h3-wifi-bluetooth-le-hdmi-and-8gb-emmc-flash/

Help me for choose the best compatible WiFi Dongle for Orange PI PC v1.2 Maybe exist list supported wifi dongle?

Does anyone know if the Zero's on board WiFi chip XR819 can be disabled? The RJ45 is disabled by default, so there must be a way to disable the XR819 - right? Any thought appreciated.

Hi all, I've been using the A20-Lime2 together with Armbian for about two years now and I love the effort that the developers and the community have put into this amazing product. Until not too long ago I was on Debian 8 (jessie) on the legacy kernel for webcam compatibility reasons (after having tried switching to mainline from time to time). With the release of Debian 9 I finally had everything that I was looking for in the mainline kernel so I decided to upgrade to Debian 9 and then switch to the mainline kernel. I'm currently on ARMBIAN 5.38 stable with 4.14.15-sunxi and just had to force a reboot. The server I'm running is mainly a webserver, …

I have an Orange pi +2e running the desktop version of armbian. I want to install armbian to the built in emmc . Armbian is currently running on a SD card when I used the command "nand-sata-install" I got these options. which of those do i select to install Armbian from the SD card to the Built in emmc

Dear colleagues, good afternoon. I have 3 problems with the display. I have a orange pi zero. Installed armbian. I set the 2.8-inch display ili9341 spi for instructions, all works very well, but ... expansion of the display - 320x240. But the system is set up as 640x480. Font on the console - Terminus framebufer 6x12. And I am looking for a smaller. Help me please. I want to make the setting expand in the system - 320x240. Font still less. And it passes the wrong color, and I want to make the right color.

Hi everyone, First of allm thank you for all the stuff on your site / forum, I recently decided to give a try to an orange pi board, and chose the orange pi plus. I have downloaded and installed the raw file of jessie desktop found on the site, and then tried to launch it. At the first startup, I had a message about my ethernet connector, gmac probed... no PHY... and then the process continue, the card shut down. I unplug/plug in the power supply, and then the board correctly boot up, and I was able to log in. The wifi is working fine (I use it now), but I don't have the ethernet connection. The ethernet cable is plug in, my ISP's router has a DHCP server…

Recently i have been experimenting with interrupts on orange pi zero plus2-H3 trying to capture data-ready pulses from an external adc on gpio PA19. The aim is to synchronize spi-read-data transactions with the incoming adc data-ready signal. First I tried to get it to work on legacy kernel 3.4 by adding the following section in to /boot/script.fex and compile the .fex file to .bin file using fex2bin: [gpio_para] gpio_used = 1 gpio_num = 6 .... gpio_pin_6 = port:PA19<0><default><default><1> This configured the pin properly as i had tested on other pins with some leds and it works. The driver code for capturing the interrupt was based o…

Hello, Trying to figure out to get bluetooth working on Cubietruck with Armbian Buster mainline based kernel 5.4.y Installed all software but bluetoothctl keeps telling me there is no default controller. Seems to me the drivers are not loaded/activated. Is this supposed to work or m i trying to fix someting unfixable. Please bump me in the right direction.. Tjabks!

no led, no output, tried it with 3 different 16gb class 10 sandisk sd cards, previous versions works fine, and i also tried the download from torrents and the direct downloads, still nothing

I should have known better..... today i did an apt update and saw thet there was an update to 5.38. Installed it and like with nearly every last update the device (OrangePi +) didn't boot. Did you even test updates in the stable repo before ? Don't know whats going wrong, so i will test it, but thats annoying.....

Hi guys, I noticed when i switch over to wifi only and turn of the ethernet connection i get issues... ping 192.168.1.12 PING 192.168.1.12 (192.168.1.12): 56 data bytes 64 bytes from 192.168.1.12: icmp_seq=2 ttl=64 time=522.139 ms 64 bytes from 192.168.1.12: icmp_seq=3 ttl=64 time=237.595 ms 64 bytes from 192.168.1.12: icmp_seq=4 ttl=64 time=971.235 ms 64 bytes from 192.168.1.12: icmp_seq=5 ttl=64 time=280.141 ms 64 bytes from 192.168.1.12: icmp_seq=6 ttl=64 time=243.838 ms 64 bytes from 192.168.1.12: icmp_seq=7 ttl=64 time=420.975 ms 64 bytes from 192.168.1.12: icmp_seq=8 ttl=64 time=25.459 ms 64 bytes from 192.168.1.12: icmp_seq=9 ttl=64 time=352.204 ms 64 bytes …

Hello! I am trying to get the cedar_ve device working for OPIZ2W. I am currently running this image: Orangepizero2w_1.0.4_ubuntu_noble_server_linux6.1.31 My uname -a: Linux orangepizero2w 6.1.31-sun50iw9 #1.0.4 SMP Wed Oct 9 13:39:53 CST 2024 aarch64 aarch64 aarch64 GNU/Linux To do this I am trying to follow these steps: 1. Modify a dts for OPIZ2W to include cedar_ve. 2. Donwloan cedrus driver and build it. 3. Compile modified ffmpeg with x264cedrus support Have anyone tried this? I have only found builds for recent kernel for the H3 CPU, none for the H618. I am looking for a DTS that su…

Hello, Since a week I try moving the OS on the sdcard to an attached SSD. OS: Armbian 5.65 Ubuntu Xenial 3.4.113 desktop Because the BPIM1 has a genuime SATA interface it should work. I have found dozens of tutorials how to do this. Until now I did not find any tutorial that works. Of course I started with nand-install expecting this would work out of the box. But after the install and rebooting I got the notification that it couldn't find the ssd. I guess I have to change something in the bootloader on the sdcard? (I am not a Linux expert but an enthustiastic Linux user) Is there any working tutorial including the final…

I've a opi zero running the latest armbian stable release, it just handle a pihole dhcp server and run the transmission client, but randomly stuck becoming inaccessible through ssh and webserver pages. All return normal when it restart by manual removing the power supply, but this way it's very uncomfortable, so what could be the cause? Is there a way to log the system errors for read them the next reboot? Thanks

I have a Orange Pi Zero with the MX25L1606E (16Mb) NOR Flash is it possible flash uboot to the nor flash and boot a OS from the USB port and how? All without using a SD card

Hello, I leave in a place where we occasionally get really heavy storms or the power gets cut for some reason. This most often does not happen more than five minutes, but there has been longer cases. Now, this poses an obvious problem with my headless server (Orange Pi PC btw). I went on a week trip last month, to discover the development board I needed was completely down. I called a friend and the power had indeed been cut off in my neighbourhood, but my server would no longer respond over SSH. I hard reset the server by power cable and tried restarting sshd (after getting home a week later), just to get warning that the action of the service was queued and afterwards w…

Hi, I'm trying to use bluetooth with the Mainline 4.11.9-sun8i armbian kernel (I also tried 4.11.7-sun8i). I activated ttyS3 (uart3) in armbianEnv.txt: verbosity=1 logo=disabled console=serial overlay_prefix=sun8i-h3 rootdev=UUID=59c35982-ddad-4bf0-8b72-a8974bfe88a6 rootfstype=ext4 overlays=uart3 spi-spidev param_uart3_rtscts=1 param_spidev_spi_bus=0 Unfortunately hciconfig -a does not find any device. I already tried to set the baudrate but no chance to get bluetooth alive: service bluetooth stop rfkill unblock all echo "0" > /sys/class/rfkill/rfkill0/state echo "1" > /sys/class/rfkill/rfkill0/state echo …

I coudn't find in menu System -> Install optin for cloning OS from SD to eMMC. How can I get it back as on older version? Boards are Orange Pi +2E and Orange Pi PC+ OS Armbian v5.91 I tied even: git clone https://github.com/armbian/config cd config bash debian-config but same... Thx

Hi all, traditionally I have used Bananian on the Bannan Pi M1+, but I thought that I would give Armbian a go as there seems to be more activity here and there are tools for compiling an entire image from scratch :-) So far I love Ambian, thank you for the work. I have tried the vanilla Jessie image (both downloaded from here and compiled myself) on the Banana Pi M1+ and with the exception of the WiFi issuet which I solved from this forum, all ran well. However I can't seem to find an SPI driver. My apologies if there is another forum post about this, I did try searching but the search function removed SPI from the query due to it being less than 4 chars :-( When…

Hi there Have purchased a Lime 2 device, as it offered GigE-which my Pi's dont :-) Loaded up both the vanilla and the normal distro's but both have this annoying habit of the device just goes to sleep-sometimes after a few hours. When I say sleep, I can still see the Ethernet LED's blinking away-but it wont respond to PING's, and it wont respond to SSH. Plugging in a monitor and keyboard doesn't bring it back to life either. If I power recycle it (2.5A unit being used-have tried the OTG and the 5vdc but no difference), up she comes. Fully updated in terms of packages. I have even set up a continuous ping to my home router from the Lime 2 (its on my internal LAN) to see …

Hi, I can't make usb otg works on orange pi pc armbian stretch. Linux orangepipc 4.19.38-sunxi #5.83 SMP Fri May 3 23:33:25 CEST 2019 armv7l GNU/Linux At boot there is the following message in dmesg: [ 2.252841] usb0-vbus: disabling I tried to enable usbhost0 with armbianconfig overlays, but it doesn't make a difference. Any suggestions ? thanks

Hello, There seems to be scant details about the NanoPi Neo 2 LTS, so I thought I'd contribute some. My testing is much less formal than how some would measure it. What I especially like to do in the way of network speed testing are the "worst-case scenarios". My way of invoking a sort of "torture test" is to mostly test upload speeds (as they tend to be slower than download speeds), both large files (much easier), as well as uploading many tiny files (much more gruelling to store, so is therefore a major "torture test"). Having said that, I'll usually favor all-GbE networking (noting which I'm using, GbE or wifi), because I know GbE will b…

I don't know if this is something I have broken or not, but I have a \var\log and a \var\log.hdd both identical and both being updated. Where should I be looking to rectify this duplication? ARMBIAN 5.25 stable Debian GNU/Linux 8 (jessie) 3.4.113-sun8i OrangePiZero