Allwinner sunxi

I there i use the update my orange pi zero to latest version 04/05/17 and no simply dosen´t boot anymore! any thing i can do?

I notice there is a 16mb spi flash on the bottom of my orange pi zero. I read it is possible to boot off it. Has anyone done it, and is it useful? Is it possible to run without the sd card? I am interested in locking the sdcard to read only for reliability during power loss, and storing application configuration data to the spi flash if possible. Can it be mounted with a filesystem, or is it better to use a ramdisk and store it periodically to flash?

I'm working on a Duo project that needs SPI and this is how I configured and tested it without the mini shield. Requirements: NanoPi Duo with test Armbian image 1 female to female jumper wire Enable SPI on boot: sudo nano /boot/armbianEnv.txt Add spi-spidev to overlays= Add line param_spidev_spi_bus=1 sudo reboot If everything worked you should have /dev/spidev1.0. Check with ls /dev/spi*. Now we can test with a C program: cd wget http://www.raspibo.org/renzo/spidev_test.c gcc -o spidev_test spidev_test.c sudo ./spidev_test -D /dev/spidev1.0 spi device: /dev/spidev1.0 spi mode: 0 bits per word: 8 max speed: 500…

Hello guys, do you know what might cause this error, it seems my "smart home" controller is not booting up anymore. In the last 2 weeks it happent again to not display any webpage while accessing it by IP, also the SSH was not working, all leds ware blinking like usually are, like there was normal activity, but it didn't respond to any request, only the ping was working, anything else was not (apache, samba, ssh). I turned it off by long-pressing the power button, it booted up, showing this warning "warning bad CRC - using default enviroment" and it passed by, showing the armbian logo and a blinking cursor, but that's it, nothing more. I think it …

Hi folks, A few months back, I set up an Orange Pi Prime on Armbian Bionic (Armbian_5.52.180715_Orangepiprime_Ubuntu_bionic_dev_4.18.0-rc4.7z). I'm now putting together a home automation workshop around this configuration, but it looks like it's now missing from the website (https://www.armbian.com/orange-pi-prime/) and download site (https://dl.armbian.com/orangepiprime/). Is Bionic no longer supported for this board, or was this an oversight? Is there something I can do to help?

I did the following upgrades this morning libcurl3:armhf (7.52.1-5+deb9u8, 7.52.1-5+deb9u9), libgd3:armhf (2.2.4-2+deb9u3, 2.2.4-2+deb9u4), armbian-config:armhf (5.72, 5.74), linux-headers-next-sunxi:armhf (5.70, 5.73), linux-image-next-sunxi:armhf (5.70, 5.73), curl:armhf (7.52.1-5+deb9u8, 7.52.1-5+deb9u9), libcurl3-gnutls:armhf (7.52.1-5+deb9u8, 7.52.1-5+deb9u9), linux-dtb-next-sunxi:armhf (5.70, 5.73), base-files:armhf (9.9+deb9u6, 9.9+deb9u7) and found my I2C bus not working anymore. I did a scan on the 4 buses (Olinuxino Micro A20) and found a device on i2c-1 instead of i2c-0, changed my settings and all worked again, so I guess one of the updates must…

Hello, I had a telecommunication technician logged onto my router + later that night a power outage. Now my pi (not sure before or after or related to anything), now the lights go on the pi (both + the one on the network), I can see it on the router with an IP but that is it. I can't logon to it on that IP with Putty nor can I ping it from the console on the PC. I tried now 3-4 of the builds (older ones, one official one and so on) with the flash card, but always the same. I don't have an USB to TTL converter to try that route. Is there anything else I can do? There is no way to do a hard reset, right?

Is there any working image for Nano Pi Air that supports in same time: - Record in the format of the mpeg4 pipeline, the video codec used is h264. Resolution 1024x768 - Ability to transmit video over WiFi (WiFi AP mode), RTSP protocol. - Ability to connect via USB to transfer recorded files to a PC (USB device mode) - Update firmware via USB (FEL mode for Allwinner SOC)

Hello, I've been working with my Banana Pro since years with Bananian. Last days I formatted the SD and installed Armbian (debian), to be used in headless mode. Installation and system setup worked as expected, I modified eth0 setup for static IP and it went fine after reboot. A strange problem appeared when I installed transmission-daemon, minidlna and samba packages. All working fine before reboot, but thereafter any network interface is disappeared, network-manager can't execute fine, remains running for several seconds then something crashes. If I configure eth0 manually network works, so no hardware problem. I'm sure the board work…

Hello, I've been trying to install Raspotify on my NeoPlus2. While it seems to be install OK, I can't find my device available in the list of Spotify-connect capable devices. journalctl -u raspotify reports: gtj@nanopineoplus2:~$ journalctl -u raspotify -- Logs begin at Mon 2020-05-04 02:26:25 UTC, end at Mon 2020-05-04 02:43:52 UTC May 04 02:26:32 nanopineoplus2 systemd[1]: Starting Raspotify... May 04 02:26:32 nanopineoplus2 systemd[1]: Started Raspotify. May 04 02:26:32 nanopineoplus2 librespot[963]: [2020-05-04T02:26:32Z INFO libre May 04 02:26:33 nanopineoplus2 librespot[963]: thread 'main' panicked at 'called May 04 02:26:3…

Hello guys, I've been playing around with the build-in lima drivers but didn't get it to work on BananaPro using Armbian_20.02.1_Bananapipro_buster_current_5.4.20_desktop image. I installed drivers armsoc, modesetting, fbdev from debian buster repos but "Xorg -configure" fails. /var/log/Xorg.0.log says: and and generated xorg.conf: Any suggestions what I am doing wrong? regards

Hello, I am using the Armbian 22.08.2 Jammy with Linux 5.15.69-sunxi. When I issue "aplay /usr/share/sounds/alsa/Front_Center.wav" or "speaker-test -t wav" playback misses a few seconds from the beginning of the audio file. If I restart it immediately, I can hear the file playing correctly. Then I wait for a while, run it and the problem reappears. I read on this forum that people have had the same problem for years without finding a solution. Is there a solution or does anyone wise know what the problem is?

Hello, I try to enable audio linein, controls with alsamixer are the following. Is it possible to redirect audio input to output directly or with audio equalizer ? I actually have sound with a speaker test, but I can't listen to the audio line-inActually I have sound with speaker test, but I can't listen audio linein Best regards

Hi, as I had set up my CubieTruck I decided to go with Legacy Wheezy ... Now I think about become a bit more current :-) Option 1 is to Upgrade to Legacy Jessie ... This is described in the documentation and hopefully should work that way, Correkt? Or Option 2 would be to go to Vanilla Jessie. Is this possible too? How? Thank you for your support, Ingo

Hello. I soldered CR2032 battery to BAT1 on Banana pro board. Setup current date and time. But RTC not working. :-( When I restart the board I see old date and time. Please tell me, how can I turn on RTC?

Dear all, we need some help from Banana Pi M2 (not that important), Cubox-i/UDOO and ODROID XU4 users. Please look through this Github issue and also have look how we currently handle IRQ redistribution on various board families (example 1 and example 2) Since irqbalanced on ARM is broken (and if it would work it's often counterproductive) assigning IRQs statically to specific CPU cores increases overall system performance slightly for free. We do this for A20 boards for years (dual core --> sending Ethernet to second CPU core), extended this on H3 boards a few months ago (quad core and somewhat complicated due to the count of different boards exposing diff…

------------------------------------------------ **** RESOLVED **** ---------------------------------------------------- 20 years of experience in computer science and I look like an idiot front of my OrangePI PC... You want to have a working HDMI LCD SCREEN with your ORANGEPI PC and you want to learn fast… Read this small tutorial, sorry my english it not perfect and if I make some error during this tutorial, please admin just correct me inside the post. First of all, if you think you know something when you receive your orangepi haha, clear your memory my friend, orangepi is not a pc … is not a RASPBERRY so don’t try RASPBERRY tutorial …

Hi and Happy new year! I'm not so fluent in English, so please excuse me. I have Lamobo R-1 with HW mod (RT5572) and the main problem is that hostapd is giving error message at start: root@lamobo-r1:~# hostapd -d /etc/hostapd/hostapd.conf random: Trying to read entropy from /dev/random Configuration file: /etc/hostapd/hostapd.conf rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0 nl80211: Supported cipher 00-0f-ac:1 nl80211: Supported cipher 00-0f-ac:5 nl80211: Supported cipher 00-0f-ac:2 nl80211: Supported cipher 00-0f-ac:4 nl80211: Supported cipher 00-0f-ac:10 nl80211: Supported cipher 00-0f-ac:8 nl80211: Supported cipher 00-0f-ac:9 nl80211: Using driv…

I'm using Mainline 4.9.5 for cubieboard2 (Armbian_5.24_Cubieboard2_Debian_jessie_next_4.9.5.7z). I boot without LAN or WIFI dongle using TTL port to get console interface. When I try to log how root ( root / 1234 ) the log system throw me always in error: cubieboard2 login: root Login incorrect cubieboard2 login: When I confirm root username the system don't ask me to insert the default password (1234) but after a while send me a 'Login incorrect'. LOG from sudo screen /dev/ttyUSB0 115200: U-Boot SPL 2017.01-armbian (Jan 20 2017 - 22:22:43) DRAM: 1024 MiB CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 Trying to boot from MMC1 U-Boot 2017.01-armbian (Jan 20 20…

I installed Armbian xenial 3.4.112 on an Orange Pi PC in July of 2016. It ran non-stop until sometime in February. I realized it was no longer sending data to the internet. When I checked, the Orange Pi PC was still powered. However, the green+yellow ethernet LEDs were both blinking together at what looked like 2sec intervals. After only a short time of running, the CPU was already 84C. When I originally had put the Orange Pi PC into service, it would remain close to 43C. I connected a monitor and keyboard. It booted and a look at syslog showed the eth0 was looping on `DHCPDISCOVER`. I tried `ifconfig etho down` and `ifconfi…

I just updated two Orange Pi One boards and rebooted them to get to the new kernel only to have them boot loop. I know, development, not supported. I'm not asking for a solution, I'm just alerting people to the situation so they can avoid messing up their boxes. Console log attached if you're curious. orangepione.txt

Board OPi Zero 512, NEXT kernel 4.13.7, last Sunday compiled. I'm trying do start more than one Dallas 1 wire interface. My primary idea was to add second w1-gpio overlay but no success. The next one is to edit device tree for w1-gpio to add another pin, and then to edit fixup script. And need some help to understand this ( copied from sun8i-h3-w1-gpio.dts ) fragment@0 { target = <&pio>; __overlay__ { w1_pins: w1_pins { pins = "PD14"; function = "gpio_in"; }; }; }; fragment@1 { target-path = "/"; __overlay__ { onewire@0 { compatible = "w1-gpio"; pinctrl-names = "default"; pinctrl-0 = <&w1_pins>; gpios …

I want to wake up my orange pi plus 2e device through the pin. It will feature a PIR sensor on this pin. I did research in the forum, but I could not find any documents. We can wake up by applying a interrupt like Arduino through a pin. How do I follow a path for this device? When I take the device to sleep, I can not wake it up again. The buttons on it do not function at all.

I would like to save the pain of all the newcommers in setting up the hotspot on their OPi ZERO. Please note, that the wifi module on this board is crappy and the available driver is barely working. The AP function is left enabled in the beta builds. You can read about it here: thread about the wifi module I am not a dev or any highly experienced user. I tested this step by step with my Orange Pi Zero 256MB, board rev. 1.1: 1) download the image from dl.armbian.com: Armbian_5.35_Orangepizero_Ubuntu_xenial_default_3.4.113 2) write it to your SD card 3) SSH to your OPi Zero 4) run as root armbian-config 5) navigat…

I've tried to the best of my abilities, but it seems that the current Bionic image does not support the K1 Plus wifi? Is that correct? In armbian-config there is no option to setup wireless and I cannot get the board to recognise a wlan0 device by changing the interfaces configurtation.. Is there some trick?

I'm trying to check if UART on my Orange PI is working. I've enabled UART via armbian-config and rebooted OPi. root@orangepipc:~# dmesg|grep tty [ 0.000000] Kernel command line: root=UUID=e5185d19-ff08-47bb-8673-1779ef917d92 rootwait rootfstype=ext4 console=ttyS0,115200 console=tty1 hdmi.audio=EDID:0 disp.screen0_output_mode=1920x1080p60 panic=10 consoleblank=0 loglevel=1 ubootpart=530c2b83-01 ubootsource=mmc usb-storage.quirks=0x2537:0x1066:u,0x2537:0x1068:u sunxi_ve_mem_reserve=0 sunxi_g2d_mem_reserve=0 sunxi_fb_mem_reserve=16 cgroup_enable=memory swapaccount=1 [ 0.000189] console [tty1] enabled [ 1.975487] console [ttyS0] disabled [ 1.995…

I came across this thread but don't think I could get the reset button working (as it should). What am I missing? I followed exactly the correct 'short-ed' pins as the pic, but still no luck. Please suggest. Thanks!

I have a 512 MB RAM, 4GB Toshiba NAND PocketCHIP with a custome u-boot supporting USB Booting and decided to test the latest armbian community image for the PocketCHIP (https://github.com/armbian/community/releases/download/26.2.0-trunk.668/Armbian_community_26.2.0-trunk.668_Pocketchip-sd_trixie_current_6.18.20_minimal.img.xz) Boot seems to start fine with all kernel files load confirmed by u-boot output (vmlinuz, ramdisk dtb, etc) but then it goes mute while starting the kernel @TheSnowfield, you are listed as the pocketchip board maintainer (thanks a lot for your contribution! 🙏), any ideas of what am I missing? Do you have a suggestion for a w…

hi all, is possible convert cubietruck on cubiebord to virtual machine?

Allwinner video HW decoding on A10/A20 using VDPAU and GLES zero-copy support for Linux There is (unofficial) support available for video HW decoding and embedding the video zero-copy via GLES within Kodi using libvdpau-sunxi and VDPAU, i.e. unlike the kodi support from rella/empatzero/others the GLES layering (video overlays) do work completely in this implementation. Additionally my driver implementation supports DivX/XVID/MS-MPEG and has sprite support for MPEG-4 over the official libvdpau-sunxi implementation. Additionally there is HW JPEG decoding support available in Kodi too, e.g. watching photos these get decoded via the Allwinner HW. (unluckily pic thumbnails…

Hi, It is nice to join in and be part of a such fast growing UOS. I would like get some advice and solve the following scenarios: * Internet Sharing with one Client only, no 'switch' needed, this has been accomplished with the instructions in https://wiki.archlinux.org/index.php/Internet_sharing, so all the iptables rules and NAT is done with success. I am able to navigate the internet from OPI-PC. * which armbian version for the smallest server to run on OPI PC, that will provide some web services. * Need to be able to access OPI-PC from the external world (from PC-3), this is what i am struggling to get it right. Say i want to connect to OPI PC …

Hi all, First of all i check the HDMI connection with a raspberry (raspbian) and OrangePi (armbian) and it works on my screen. But on the BPI-M2 dosnt work... i try with Debian Jessie upgraded, with a fresh install outdated of Debian Jessie and i try too Debian Jessie Desktop... No works... I try too with other bpi-m2 board, and the issue stills... So isnt a hardware fail... there are any config or special command tu turn on? I see the boot.src and all apparently are ok. Best regards

Hi all, I was just wondering if you had experience with the performance on the H3 allwinner CPU performance based on the cpu temperature ? I'm trying to tweak my fan to only cool down the CPU once it gets close to peak cpu temperature levels, before performance starts to degrade. According to the Allwinner H3 datasheet the maximum ambient operating temperature is 70° (see page 612) http://dl.linux-sunxi.org/H3/Allwinner_H3_Datasheet_V1.0.pdf Do you think I can let the cpu go up to 70 before cooling it down or should I start sooner (i.e 65° / 67°) to keep my pi at top performance ?

I have built Armbian system from sources for my OPi Lite and when I'm trying to change resolution of monitor connected by HDMI I get this: arti@orangepilite:~$ sudo h3disp -m 1080p60 Now trying to patch script.bin with your settings. Aborted Could not convert script.bin to fex. Exiting arti@orangepilite:~$ sudo h3disp -m 10 Now trying to patch script.bin with your settings. Aborted Could not convert script.bin to fex. Exiting What should I do to make this work?

I'm looking to add two ENC28J60 Ethernet interfaces to my OPI, does it have two SPI interfaces available? From my reading, it appears the onboard NAND flash takes up one SPI interface, but I cannot find any information on whether there is 1 or 2 other SPI interfaces available?

I bought orange pi win plus and I began to use armbian. Nearly everything ok but I can not use my bluetooth keyboard. There is a bluetooth symbol and I can enable it but when I wanna add my keyboard it says no adapter found... Please help me ..

Hi friends, one question - this camera works with Orange Pi zero2Plus for me (mostly). But do I need to use always the green PCB with camera, or can I directly plug in the small black camera with its brown ribbon to Orange Pi? Should it work without green PCB or not? Many thanks.

Hallo, i have an old istallation of armbian and it's working perfect , thank you Igor for your work..! i want to upgrade my stable debian wheezy without breaking nothing :p the current version of armbian is : Linux cubietruck 3.4.104-sunxi #1 SMP PREEMPT Fri Oct 17 16:13:30 CEST 2014 armv7l GNU/Linux and the : /etc/apt/sources.list deb http://ftp.it.debian.org/debian wheezy main contrib non-free deb-src http://ftp.it.debian.org/debian wheezy main contrib non-free deb http://ftp.debian.org/debian/ wheezy-updates main contrib non-free deb-src http://ftp.debian.org/debian/ wheezy-updates main contrib non-fre…

Hi, I am facing an i2c problem on orange pi 3. The i2c0 is enabled in armbian-config. The i2cdetect output is correct, as I know my two slave boards connecting to gpio pin3 (SDA) and pin5(SCL) have the addresses 0x20 and 0x23. pi@orangepi3:~$ sudo i2cdetect -y 0 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: 20 -- -- 23 -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -…

Hi everyone. I almost gave up while reading tons of forums:( I bought CO2 sensor MH-Z19 from aliexpress. As I figured out this sensor used by RPi without any problems. Manual I found here: https://www.circuits.dk/testing-mh-z19-ndir-co2-sensor-module/ I connected module as mentioned: Vin - 2 pin gpio GND - 9 pin Tx - 13 pin Rx - 11 pin Module was blinking when I powered on my OPi, but when I tried to send data to UART nothing happened. I got timeout. I tried to connect Tx and Rx (11 and 13 pin) by cable, then sent bytes and immediatley got answer, UART work, as I understood. I checked uart in armbian-config menu and all (…

Hi. I run armbian on a opi pc for a while. It works fine for a couple days when I work with this board. After that I left the board unpowered for two weeks or so and when I want to powered it on, it does not boot, I need to reconnect the power again to boot. This was the first time when I encountered a problem, the uptime was wrong, it is shows me 2 weeks, I reboot the board and it was ok after, it stays on and all worked fine for 10 hours until I shut it down. But I had this problem often, doest not want to boot from first time, board freeze after some time and I need to reboot to work properly. Uptime and date/time is correct but when I want to see the statu…

I have a problem with my wireguard implementation. When connected through it I get lag spikes every few seconds. What might be the cause and solution to this? It is not the internet connection/cable/etc because a raspberry pi running wireguard works fine on the same exact cable, port etc.

Greetings from USA, my name is Freddy Love and i'm new to Armbian and this forum. Currently i'm using a Lime2 no internal storage with Bullseye CLI on the SD. My pau06 works great, but want to use for small server and would obvi prefer to be hardwired in. Any help would be much appreciated. I'm still going thru everything I can read. My email is freddylovesart@protonmail.com and @freddylove@fosstodon.org // thx in advance. Sincerely, -fl

Hi Forum Members, I need have to activate a 1-wire thermal sensor DS1820 on al old BPI M1. I've had these type of sensors allready runing on a BPI M2Zero under Buster (Armbian Kernel: 5.10.60-sunxi) wih these settings in /boot/armbianEnv.txt: overlays=w1-gpio param_w1_pin=PA6 dmesg | grep -E 'w1|wire' [ 6.806929] Driver for 1-wire Dallas network protocol. [ 6.847601] gpio-6 (onewire@0): enforced open drain please flag it properly in DT/ACPI DSDT/board file [ 6.875871] w1_master_driver w1_bus_master1: Attaching one wire slave 28.0121121d29c5 crc 9a [ 7.020059] w1_master_driver w1_bus_master1: Attaching one wire slave 28.01211…

Cubieboard2 How to create the armbian image with capability of booting with gps connected to the uart port ? The armbian can't start if gps connected to the uart port and vice versa - It starts with unpluged gps. After system is started up, I do connect the gps and can easily get the gps data from /dev/ttyS0 As I understand - it's happened because of ttyS0 can be using as keyboard, so bootload is interrupting. Also it's can be a problem while initial password changing.

Hi, guys, great stuff here ! I am testing: Orange Pi One, 8GB SD Armbian 3.4.110-sun8i MotionEye, (great stuff https://github.com/ccrisan/motioneye/wiki) It all is working very well, (only a few resolutions like 1440x960 are usable for now). Much better than the old and too slow RPi1, being replaced But my var/log/syslog is filling op rapidly with warnings about the Orange Pi Camera module. 5-6 lines per second : May 3 23:44:11 OrangePi01 kernel: [ 1713.501813] [VFE_WARN] Nobody is waiting on this video buffer,buf = 0xd38b7c80 May 3 23:44:11 OrangePi02 kernel: [ 1713.742666] [VFE_WARN]Only two buffer left for csi May 3 23:44:11 OrangePi02 kernel: [ 1…

Hello, I try use UART interface on Lime2, but have problems with data transmission. Input echo 12345 > /dev/ttyS2 Output â–’;375 UART settings stty -F /dev/ttyS2 9600 -parity cs8 -cstopb How to detect the problem? Thanks

Hi everyone, I have recently buy a Orange Pi plus 2e. I installed Armbian legacy/server on it. When I plug a 3.5 HDD (in self-powered USB box), I have this message in log (dmesg) : [ 13.654305] ehci_irq: highspeed device connect [ 13.920099] usb 3-1: new high-speed USB device number 2 using sunxi-ehci [ 14.074826] scsi0 : usb-storage 3-1:1.0 [ 15.070939] scsi 0:0:0:0: Direct-Access WDC WD30 EFRX-68EUZN0 PQ: 0 ANSI: 5 [ 15.073286] sd 0:0:0:0: [sda] Very big device. Trying to use READ CAPACITY(16). [ 15.073771] sd 0:0:0:0: [sda] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) [ 15.074679] sd 0:0:0:0: [sda] Write Protect is off [ 15…

I have an Orangepiplus2e when I ran the command nand-sata-install after selecting boot from emmc system on sata or usb and selecting the destination/dev/sdb1 it shows the error of Partition too small. Needed: 3857 Mb Avaliable: 2700 Mb, How do I solve this?

Hey there So I was planning on using the OPZero on a robot that I had already made, which took use of SPIdev, and it was doing calls to the spidev driver in C. Now I noticed that the OPZero has 2 SPI channels, one for the NOR flash (Which isnt populated) on the back and another that goes to the GPIO headers on the device. Now I ran my script, and turns out that /dev/spidev0.0 is actually writing SPI commands to the rear SPI channel. This is apparenly SPI0 according to the schematics. Now following the schematics again, I want to access SPI1, which currently does not exist as a spidev file. I tried "modprobe spidev" to bring up the extra interface, but sadl…

I read this post http://felenasoft.com/xeoma/en/articles/raspberry/ Whether it will work for armbian?

Hello. Yesterday i tried to switch kernel in debian jessie 5.24 from 3.4.113 to 4.x using this article: To make sure you won’t run into conflicts within newly installed packages, remove them all before upgrade: 1 2 aptitude remove ~nlinux-dtb ~nlinux-u-boot ~nlinux-image ~nlinux-headers aptitude remove ~nlinux-firmware ~narmbian-firmware ~nlinux-$(lsb_release -cs)-root Proceed with install: 1 2 3 4 apt-get install linux-image-dev-sun8i linux-dtb-dev-sun8i linux-headers-dev-sun8i apt-get install linux-u-boot-orangepizero-dev linux-$(lsb_release -cs)-root-dev-orangepizero apt-get install armbi…

Hello i've updated the kernel from the legacy to the dev using the procedure To make sure you won’t run into conflicts within newly installed packages, remove them all before upgrade: 1 2 aptitude remove ~nlinux-dtb ~nlinux-u-boot ~nlinux-image ~nlinux-headers aptitude remove ~nlinux-firmware ~narmbian-firmware ~nlinux-$(lsb_release -cs)-root Proceed with install: 1 2 3 4 …

Hello guys, I read a lot but did not find the answer I'm trying to Turn ON / Turn OFF my Orange pi lite HDMI output like with my raspberry pi (with the help of /opt/vc/bin/tvservice -o ... etc) But I'm not able to find a similar command to do it. I only found some tips to do it at start-up only My goal is, after some times, turn OFF HDMI output (via python script) to force my monitor to switch into sleep mode. Do you have any ideas ? Thanks in advance Max

Hi, I am running armbian 4.11.6-sunxi with xfce4 on a Banana Pi M1. I need to login automatically without having to choose a session before login to the xserver. I am achieving the autologin OK but can't get rid of the session request . How can I achieve autologin complete with new session? Thanks for helping if you have an answer.

Hey everyone, I wrote a guide a while back on setting up Armbian on the Orange Pi Zero, with key-based ssh access enabled. Thought I'd share it with this forum I'd love feedback, questions and also definitely send pull requests if you have any edits or changes to propose!

Hello folks, I'm having trouble booting https://dl.armbian.com/lime-a64/Debian_stretch_next_nightly.7z as of today on my A64-OLinuXino-1G4GW. Armbian is installed on an external µSD card; the device has internal flash. Do you see, how I can fix this issue? Thanks, yanosz Log is: U-Boot 2018.05-armbian (Aug 21 2018 - 08:46:56 +0200) Allwinner Technology CPU: Allwinner A64 (SUN50I) Model: Olimex A64-Olinuxino DRAM: 1 GiB MMC: SUNXI SD/MMC: 0, SUNXI SD/MMC: 1 Loading Environment from EXT4... ** File not found /boot/boot.env ** ** Unable to read "/boot/boot.env" from mmc0:1 ** Failed (-5) In: serial Out: s…

Hello, I don't know if this is board related or probably armbian related... anyway. In my old banana pi (4.19.13-sunxi) htop (version 2.1.1) is like this: While on every other linux PC, server or whatever I have it looks like: The small and stupid difference is in those blue "tree view" lines (under the Command column), which I don't really like nor understand. Is there a way to set those lines as they normally should be? (and why was it set???) Thanks

Hello, i'M having this issue with the latest Armbian 5.75 stretch image with updated firmware. When booting with a huwei E303 modem is in the usb port the board fall in a eternal reboot. if i let the board boot as normal an then insert the modem everything is o.k. I tried with 4 others OPI PC+ and others E303 sticks, same thing. also tried with 5.65, same problem. BUT, with an earlier version 5.35 and it boots as normal.

Hello, I have been struggling for some time with random freezes. I am running application with i2c0 Fram and UART1 for transferring/receiving data based on MAX3232. The freezes cause no response from Orange PI (debug UART too), only unplug power helps. I read that it may be a problem with powering but i tried many USB power adapters 2A, 3A and ATX power (28A) connected to GND and 5v, nothing helps. I have lowered cpu max frequency to 816Mhz and still the same. All necessary data uploaded via armbianmonitor.

How can we create a custom image of Armbian Bionic/Buster for Orange Pi Zero with our customized application/code in it. Please suggest process for the same.

I have the same problem like other users here, the 1-wire doesn't run correctly, I added 1-wire to armbianEnv.txt, 1-wire drivers are loaded, but I cannot access the data of DS18B20 attached to PA06. L. ___ ____ _ _____ / _ \| _ \(_) |__ /___ _ __ ___ | | | | |_) | | / // _ \ '__/ _ \ | |_| | __/| | / /| __/ | | (_) | \___/|_| |_| /____\___|_| \___/ Welcome to Armbian 20.08.17 Bionic with Linux 5.8.16-sunxi System load: 26% Up time: 0 min Memory usage: 14% of 491M IP: 192.168.3.163 CPU temp: 45°C Usage of /: 4% of 29G Last …

good morning everyone, I installed Armbian 23.02.2 on orangepizero about a year ago without ever having a problem . Today it suddenly stopped booting and I can't get it to start again and that's what I'm interested in, also possibly to recover internal docker configurations. The orangepizero is powered by a 3A power supply under UPS and properly cooled, if I use the latest release on a new SD it works perfectly, so I think it is not a hardware problem. The SD with Armbian 23.02.2 is not corrupted and I can read every part of it. Does anyone know any tricks to get it running again?

Hi! Yesterday I upgraded my NanoPi Neo Plus2, during that the kernel version went from 6.12.74 (package version 26.2.0-trunk.478) to 6.18.19 (package version 26.2.0-trunk.626). This morning I noticed, that this kernel is missing the dm-snapshot.ko module. I searched the forum if anyone else is having this problem, but it appears I am the only one using this feature. I use snapshots to create consistent backups of the system. Is there a reason why it was removed and more importantly is there a way to get it back without having to compile the kernel myself? Greetings PS: I should note, that I want the module back in newer kernel versions in the fu…

Hello, in Armbian TCP buffers are already set. I can change them by putting new values to /etc/sysctl.conf. But, is this elegant? Or would it be better to change directly the values from armbian? In which file configures Armbian the TCP buffers? Thanks a lot and best regards, Michael

Hi, as I need to use an OS allowing me to have Cozy and Gladys (both node.js) on my router (using them it as server) I tried to use armbian for the first time. I sucessfully installed armbian on a SD Card and boot it. My BPi-R1 is not connected to a display or other periherals (keyboard / mouse). Because I do not have those materials I sold them. It is just connected with RJ45 and has a HDD connected on the SATA port. I then connected my modem RJ45 connector to my BPi-R1 on the WAN port. I connected my computer on the first port (near the WAN one). I saw my laptop do not get an IP certainly due to the fact that LAN port seems to be manually activated. …

Hello, my Beelink X2 is a Allwinner H3 TV Box and is possible to boot the Orange Pi PC Image from OrangePi.org but not from armbian. What is needed to bring this TV Box to work with armbian, I already habe a immage from Beelink X2 internal 8GB NAND. Is there a howto to get this working (Eng/Ger) Thank you. Here is smal part from NAND Image, If some one need more, I will insert it. hd BeelinkX2.img |head -n 200 00000000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 000001b0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80 00 |................| 000001c0 00 00 0b 00 00 00 00 20 33 00 00 e8 b4 00 00 00 |....... 3.....…

Hi, Just installed Armbian (5.14) on SD card and tried in my OrangePi plus. It doesn't start to boot - it does nothing. I can boot by initiating boot from the system console. I've upgraded to 5.16 but still doesn't boot. Also where do I get gpio? I notice /boot/boot.cmd uses gpio but it doesn't exist. Thanks

hello guys ! Today I have installed the armbian 5_20 desktop on my orange pi plus 2 Nice ! The network is working by setting the /etc/network/interfaces The lan0 is connected to the router by using a static IP address The wlan0 is also setted with a statis IP address The update & upgrade operations are done . Now I want to start an access point and I have tryied with the last configuration I used with armbian 5_10 but it doesn't work I have wi-fi module built-in and antenna . I think that many things are changed with tihs armbian 5_20 Does someone know which files to manipulate and how to start an access point ? Thanks and happy new year !!!

Hi. I am new to the MiniPC world and thank you for your help beforehand. I have managed to install ARMBian on my Orange Pi PC + and it occurred to me to use it as a STEAM Link with MOONLIGHT software that gives such good results in its version for Android. The linux version runs from an independent one here. The problem is that it does not let me install the dependencies, I leave them an image. I have tried it from XTerminal as from 'Synaptic Package Mannager' As I say I am new to this, if someone who knows how to operate explained it I would be very grateful. Thank you very much. //------------------------------------------\\ Spoile…

Hello, Does the wi-fi module of the Orange Pi Zero consume power when I'm not using wi-fi? If it does, can I disable it? My pi zero will be connected to ethernet 24/7 and I don't want it to consume unnecessary power. Thanks.

I've been playing with Orange Pi Zero. I've been playing with both Armbian_5.25_Orangepizero_Ubuntu_xenial_default_3.4.113.img and Armbian_5.25_Orangepizero_Debian_jessie_default_3.4.113.img . I've been using a FTDI communication Serial adapter on a Mac Laptop via Terminal $ screen ≺port_name≻ ≺baud_rate≻ In my case the screen command looked like this: $ screen /dev/tty.usbserial-AE00BS5L 115200w What I've discovered is when I'm using serial communications, tools like $ nano filenamee or $ nmtui , the system interface gets all screwed up. If you have the commands memorized, you can still use Nano (barely) but not so easy with nmtui. The scree…

Hi there, I'm trying to run luma.examples using an SSD1322 display via an SPI interface. I think I got the wiring right but the software is responding with errors. The app is expecting D/C and RESET parameter via a GPIO pin numbers to control the display.. I'm not sure how the Nano PI NEO Air physical pins are mapped to a GPIO port under Armbian. Where can I get a list of mappings for the physical pins to the GPIO pin numbers? How does this work? Is this an OS specific thing? Thanks in advance. PS: `uname -a` : Linux nanopiair 4.14.15-sunxi #23 SMP Sun Jan 28 12:46:39 CET 2018 armv7l GNU/Linux

Hi everyone, i have a strange problem with my a20 lime2 board as described in the topic. Please help The i2s0 pins should be MCLK-PB5 BCLK-PB6 LRCK-PB7 DO0-PB8. But I got data signal from PB7, and the LRCK was missing. a 24 bit 44.1khz file was played by aplay.

Hello every one I'm new to this site and I have recently purchased an Orange Pi Win Plus but got a lot of issues in configuring it. I'm now able to blink LED through Shell and C with WiringPi but I couldn't find any working Python 3 based Library for GPIO. I installed WiringPi from : https://github.com/OrangePiLibra/WiringPi This actually helped me to access GPIO through C/C++ and Shell but I couldn't find any thing for Python that's working. I came accross a new Python Library : "pyA64" but its not working. Also, the library "OPi.GPIO" doesn't supports my Board. I also tried this : https://github.com/lanefu/WiringPi-Python-OP but that's makes my "gpio" com…

Hello! Sorry, I can't speak english well! A year ago, I buy my Orange Pi PC, and download last image of Armbian, and it work's well. But yesterday, I update my system through apt-get, and notice that there be some kernel packages. There was packages, with "sunxi" or "sunx7" in his names, don't remember well. After this, my Pi stop to working. No SSH, no image from HDMI too. I download new images from https://www.armbian.com/orange-pi-pc/ try both Bionic and Stretch. But both of them don't work. There was an old image, Xenial with kernel 3.4. It works well, but my wifi adapter doesn't work with this kernel. But this adapter, worked with …

Hallo dear friend, I am a beginner . I bought a banana pi h3, I tried to turn it on, powering it to 5 volts, I connected mouse, keyboard, and monitor (with hdmi-vga adapter) but not signs of life, only the red LED is on , os image is loaded in sd card. I tried to press the on and reset buttons but nothing. I hope you can help me. Many thanks. Daniele.

Hi I try use Nokia 5110 with Orange pi zero. I found this library: https://github.com/rm-hull/luma.lcd and try to run it on my orange pi with this tutorial: http://codelectron.com/interface-nokia-5110-lcd-and-raspberry-pi-python/ so in python shell I add these: >>> from luma.core.interface.serial import spi >>> from luma.core.render import canvas >>> from luma.lcd.device import pcd8544, st7735, uc1701x >>> import OPi.GPIO as GPIO >>> from luma.lcd.aux import backlight but after add this line, I got many error that told me that library is used for Raspberry pi only: >>> serial = spi(p…

Source for kernel in package : linux-source-4.19.38-next-sunxi is for 64BIT architecture , is not possible to get source for 32bit architecture

I've got a Sony RX100VA camera that I want to connect to the NanoPi Neo2 running Armbian Buster. On the Camera I can select the type of USB connection: -Auto -Mass Storage -MTP -PC Remote My intention is to use the PC Remote connection for use with gphoto2, this works fine on a PC with Ubuntu 18.04, but when I connect the camera to the Nano Pi Neo2 with Armbian, the camera display shows connecting (but doesn't connect). I suspect a bug in the OS, but I am unsure how to find it. lsusb gives the following report with an error: can't get debug descriptor: Resource temporarily unavailable root@nanopineo2:~# lsusb -d 054c:0cb2 -v…

Hi, I try to change the language of the last OS Buster of a Cubietruck 3 in FR. The language is always in US. Thanks

How do I enable the cgroup memory controller on Armbian? I’m trying to control memory usage on my orange pi one using systemd with a unit file as follows: [Service] Slice=influxGroup.slice MemoryAccounting=true MemoryHigh=100M MemorySwapMax=250M The command systemd-cgls confirms that the influxGroup.slice has been created, yet memory is not controlled in line with the parameters in the unit file. I think the issue may be that cgroup memory controller is not enabled. I haven’t done anything to enable it, but I did notice that dmesg appears to indicate an enable statement in the kernel parameters: [ 0.000000] Kernel…

Hi, I want to use LCD on Orange Pi 3 LTS. But there are no fex/script.bin in the boot directory. The LCD pins are given the RGMII Ethernet Interface. I could not configure the device tree for internal LCD output. Could you please explain how can i use LCD on these system ? Good Work.

Hi, Is it possible to remap the i2c1 to use the i2c0 default pins via armbianEnv,txt ?. What I want to achieve is to have the PD25 and PD26 to appear as bus 1. Thank you.

Hello and Happy New Year my lovely Armbian friends! I am aware that this topic is a reoccurring one, having abused the search function beyond its functional capabilities I have found the following threads that deal with somekind of sleep and wake with separate pins for each function: how to wake up OPi3 gpio to inform of system shutdown I would like to know if it is possible to have 1 pin act as both sleep and wake depending on its voltage? - if so how could i modify one of those dts in the first link? I am new to dts so not sure how the pin mappings are assigned. for example, I have a DRV5053 hall effect sensor tha…

I'm trying to enable GPU support for watching youtube on orange pi 2 zero w model. But there is no Mali driver and even kernel package How can I enable this?

Hi! I have an old Allwinner A10 based tablet that runs on Android. I want to install some other OS on it. I tried the instructions on linux-sunxi.org and created a page for the tablet: https://linux-sunxi.org/Softwinners_crane I extracted the FEX file from an image I got from the manufacturers a long time ago: http://github.com/linux-sunxi/sunxi-boards/pull/72/files The linux-sunxi mailing list pointed out that my tablet is similar to Topwise A721, so I used that dts file to compile u-boot and the kernel, and tried to boot it through an SD card. Trying to boot that, u-boot starts, and then gets stuck at "Starting kernel..." Then I found…

Hi all! I have an Olimex Olinuxino-Lime2-4GB A10 cpu based dev board and I have installed Armbian on an SD card. Everything works fine, except when trying to compile some drivers for the wifi dongle that I want to use. The dongle has an RTL8188CUS chip, and I also have another dongle with an RTL8192CU chip, and when following the instructions found here the compilation fails, because of the kernel headers missing. The instructions work fine on other distributions. Could someone help me figure out how to successfully compile the drivers? Where can I get the kernel headers? I really need these drivers for my project.

device: orange pi pc soft: Armbian_5.14_Orangepipc_Debian_jessie_3.4.112.7z my log via serial: U-Boot SPL 2016.05-armbian (Jun 05 2016 - 09:45:23) DRAM: 1024 MiB Trying to boot from MMC1 U-Boot 2016.05-armbian (Jun 05 2016 - 09:45:23 +0200) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi PC I2C: ready DRAM: 1 GiB MMC: SUNXI SD/MMC: 0 (SD), SUNXI SD/MMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. starting USB... USB0: USB EHCI 1.00 USB1: USB OHCI 1.0 USB2: USB EHCI 1.00 USB3: USB OHCI 1.0 USB4: USB EHCI 1.00 USB5: USB OHCI 1.0 scanning bus 0 fo…

Hi guys, ive installed armbian 5.2 into my opione, now what should i do? Videos 1080p work slowly in kodi, i have to do something? Thanks Inviato dal mio HUAWEI SCL-L21 utilizzando Tapatalk

Hello I was wondering how can make possible usage of software raid1, using integrated emmc and another card placed into the slot. So far I have used that on Slackware x86 without any issue, but there I tells the Lilo to boot from /dev/md0 for example. Wonder where I should make adjustments here (in Armbian(. Can someone point me at the right direction?

Never had a problem with Armbian on my board. After last full upgrade (linux-image-next-sunxi 5.27.170427 etc) system is not booting. I tried with a fresh SD card (image Armbian_5.25_Cubieboard_Debian_jessie_next_4.9.7) - it's booting fine afresh, but also doesn't boot after full upgrade. Below are logs for both cases. Boot with old card: Spoiler U-Boot 2017.01-armbian (Feb 02 2017 - 02:20:16 +0100) Allwinner Technology CPU: Allwinner A10 (SUN4I) Model: Cubietech Cubieboard I2C: ready DRAM: 1 GiB MMC: SUNXI SD/MMC: 0 *** Warning - bad CRC, using default environment In: serial Out: …

Hello. I am trying to control a servo, and after a lot of mistakes and hits in the face... finally i can move it with WiringOP (https://github.com/zhaolei/WiringOP) I use one of the examples called servo.c and the servo moves to one side and another. This is the first step, but the servo makes weirds movements. Watch this video. Any iddeas why? Any other way to control a servo? I am not C expert, some way to do it with Python? Thank you very much in advance. servo.c

I have seen this old thread but since last post was long time ago and it was shell based I decided to go with new one ... I have the udev setup (you can see some old versions inside commented out too) root@orangepizeroplus2:~# cat /etc/udev/rules.d/60-python-pifacecommon.rules #KERNEL=="spidev*", GROUP="gpio", MODE="0660" #SUBSYSTEM=="gpio*", ACTION=="add|change", RUN+="/usr/bin/find /sys/class/gpio -exec /bin/chmod g+u {} + -exec /bin/chown :gpio {} +" #KERNEL=="gpio*", GROUP="gpio", MODE="0660" #SUBSYSTEM=="gpio*", ACTION=="add|change", RUN+="/usr/bin/find /sys/class/gpio -exec /bin/chmod g+u {} + -exec /bin/chown :gpio {} +" KERNEL=="spide…

Hi, I have a OrangePi+ 2E running ARMBIAN 5.33 user-built Debian GNU/Linux 8 (jessie) 4.13.5-sunxi The system is installed and runs well from EMMC, but now that I have it set up more or less as I want it, I tried to boot from sdcard to do a emmc backup as here I tried first plugging the original SD that was nand-installed to emmc, but the system would only boot to emmc, su did a fresh install of armbian next to a new sd card, but the system will still only boot from emmc. Any ideas? BR.

I am trying to setup a 5ghz access point on D-Link DWA-171(according to wikidevi, it's 8811au) + NanoPI NEO PLUS2. I use the testing armbian image with latest update. The hostapd can enable the 802.11a 5ghz AP mode with ht_enabled (but it says this chip doesn't support 802.11ac) I can see the SSID shows in the phone. If I try to connect it, it will fail and says the station is out of range. When the phone is trying to connect this AP, hostapd doesn't output any connection log even in debug mode. Also, although I set the channel to 40, the WIFI analyzer on the phone shows it is using 38. dmesg Spoiler …

This has been replaced by: User Space IO get more details on this thread. Well, it's time to say goodbye to sysfs and hello to libgpiod! @zador.blood.stained pointed me in the right direction, but you need to do one little hack I'll explain below involving compiler_types.h. I tested this on a NanoPi Duo, but it should work on any mainline Armbian release (and other distros as well) as long as the kernel is >= 4.8. Try ls /dev/gpiochip* and see if anything is listed. If so, then proceed. I'm continuing work on my Github site https://github.com/sgjava/libgpiod-extra, so please report any issues there. There is an Armbian install script t…

Hello, After I run apt-get update and upgrade, I lose the sound card: aplay -l aplay: device_list:268: no soundcards found... If I check my upgrade history, I can see the following: cat /var/log/apt/history.log Start-Date: 2018-03-16 22:33:12 Commandline: apt-get upgrade Upgrade: libgssapi-krb5-2:armhf (1.12.1+dfsg-19+deb8u2, 1.12.1+dfsg-19+deb8u4), tzdata:armhf (2017b-0+deb8u1, 2018c-0+deb8u1), ncurses-term:armhf (5.9+20140913-1, 5.9+20140913-1+deb8u2), libkrb5-3:armhf (1.12.1+dfsg-19+deb8u2, 1.12.1+dfsg-19+deb8u4), libk5crypto3:armhf (1.12.1+dfsg-19+deb8u2, 1.12.1+dfsg-19+deb8u4), linux-image-next-sunxi:armhf (5.34, 5.…

After along time I downloaded a new armbian image, after doing apt update/upgrade for the last year or so. I was quite surprised to see that the pcduino3nano is now deprecated, while other A20 boards are still supported. What was the exact reason that the pcduino3nano was dropped from support? If I keep using the deprecated OS, can I fully use apt update/upgrade for all user stuff? What would happen to all kernel and u-boot update packages? Is the latest armbian for the pcduino3nano automatically disabling those updates, or do I need to do something manually? *should* I block kernel & u-boot updates? thanks, Udi

Hi, I have flashed Armbian_5.35_Orangepilite_Ubuntu_xenial_default_3.4.113_desktop.img - and it works fine with my Orange Pi Lite v.1.1 But if I flash Armbian_5.38_Orangepilite_Debian_stretch_next_4.14.14.img which is aslo supported, the device does not boot. At least I get no output on HDMI, and no serial console over OTG. So I cannot check if it does not boot at all, or dies somewhere in the middle How can I check why it does not boot?