Allwinner sunxi

hi, I am th owner of a lamobo r1 card. Last days i'have tried more than 10 debian/bananian/ubuntu/raspian/openwrt image. Most of them work fine. Community image are often better than sinovoip one ... Unfortunatly, my sata HDD never work. I'm using a seagate 1TB SSHD. I currently using the armbian ubuntu image. At boot, the hdd spin up and stop, and ubuntu don't boot. If I remove the HDD everthing work fine. Anybody have a working hdd using the micro usb power port ? I use an ipad charger and a good one meter usb cable. Any help is greatly appreciated. If I should provide more details, please let me know Thanks agemio

Hi forum, I ran an apt-get upgrade a few days back and here linux-image-current-sunxi:armhf was updated from 21.05.6 to 21.08.2 After reboot my SATA was gone. There was nothing in the logs which would have indicated that something is wrong. After I reverted back to 21.05.6 apt-get install linux-image-current-sunxi=21.05.6 apt-get install armbian-firmware=21.05.8 apt-get install linux-dtb-current-sunxi=21.05.6 everything worked again. Has anyone experienced something similar ? Regards Volker

Hello Community, I have a (hopefully) quick question about the SATA port on my Bananapi. I wanted to attach a msata card via adapter to my Bananapi, like I already do on my Cubietruck. However when I start look for the msata drive it does not show up. However when I double check the drive via a USB SATA adapter the drive does show up. Could someone please tell me what is going ? Thx, blub4747

I built an unofficial Armbian 6.12.51 (Noble) image using the build tool: Armbian-unofficial_25.11.0-trunk_Nanopiduo_noble_current_6.12.51.img I am trying to get the micro-USB port to work as a USB serial gadget (g_serial / libcomposite). What I have done / observed: g_serial and libcomposite modules are loaded: lsmod | grep g_serial g_serial 12288 0 libcomposite 49152 2 g_serial,usb_f_acm ConfigFS is mounted: mount | grep configfs configfs on /sys/kernel/config type configfs (rw,nosuid,nodev,noexec,relatime) UDC exists: ls /sys/class/udc/ musb-hdrc.2.auto Gadget folder does…

hi, i've been trying to get the SC16IS752/I2C UARTs working on opi-zero using DT Overlays. Here is my .dts: /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h2", "allwinner,sun8i-h3"; fragment@0 { target = <&i2c0>; __overlay__ { #address-cells = <1>; #size-cells = <0>; status = "okay"; sc16is752: sc16is752@4D { compatible = "nxp,sc16is752"; reg = <0x4D>; clocks = <&sc16is752_clk>; interrupt-parent = <&pio&…

Hello. I decided to build an original image for my Fly Pi board. HDMI output not working. The image is shown only when loading Uboot, and then turns off and a black screen appears. Here are the logs: https://ix.io/4EWM DISPLAY=:0 xrandr output: can't open display :0 X org log: https://paste.debian.net/1290516 I'm confused and don't know what to do...

After having my old debian (wheezy? or jessy?) unbootable from systemd update I decided to clean install. Having gotten a good Power supply, an A1 Speed 10 SD card, etcher image, and armbian debian 20.08 (also tried 20.07), The board boots (Welcome to armbian) up to "network interfaces up) - then the screen goes blank/black, and I get the green led heardbeat (slow blinking) for a while. Pushing power again the board shuts down (green LED blinking rapidly for a moment, then red power LED comes off). I have had installed boot to nand / Sata disk before but all that shouldn't matter I think because the boot from SD Card seems successful - why could it be th…

Hi, By installing armbian jessie on my Orange pi plus 2 E, after login,I have a choice to change the resolution of screen( to 1920x1080),but unfortunately I have no succes. Can you please tel me how can I do that? Thanks Sadegh

Hi, who knows how to fix the problem of the displaced screen on the right? This is how Armbian appears with the latest build https://dl.armbian.com/orangepi3/nightly/Armbian_5.90.190705_Orangepi3_Ubuntu_bionic_dev_5.1.15.7z and this is how it appears to me with an old build with kernel 5.0.7, so it's not the monitor's fault Regards

Looking for recommended LCD screens for NanoPi Neo and Orange Pi Zero. I have some IoT ideas I want to explore. Does not have to be touch, and I'm pretty flexible on screen size. Actually, would like a couple of different screen sizes but bigger than an 128x64 OLED (I have that). Must be color. At least 320x240, preferably something 320x480. I just got two Orange Pi Zero systems today and want to create a couple of IoT devices along with the two NanoPi Neo systems I got recently. Performance does NOT have to be ideal, just reasonable (not going to game on it or watch action movies). The Zero means HDMI is not an option; given that, what interface is best - …

Hello everyone! I have a Cubietruck Allwiner A20 with 8G sdcard with Armbian 5.04 Debian 8 ( Jessie ) 3.4.110 - sun7i . When you start Cubietruck with sdcard Connected , I run the script /usr/lib/nand-sata-install/./nand-sata-install.sh to copy the image to sdcard NAND . The same performs all the procedures without any error until the moment of PowerOff . When turning off the disconnect sdcard and turn again , though the S.O does not start. It is as if he had not copied anything to NAND , as if empty. Has anyone had this problem ? Grateful for the support of the whol…

Hi, I tried to switch on some LED during boot with script.bin. (connected to PH11). Decompiled script.bin, changed several times PH11 to be an output with value 1 (pin 15 on GPIO3). It works if I switch it on from Linux. ; Was the first I changed lcd_used=0 lcdd11 = port:PH11<1><1><default><1> ; Whats this? Not used, or? ms_used = 0 ms_d3 = port:PH11<5><default><default><default> ; Both changed gpio_pin_19 = port:PH11<1><1><default><1> pin_19 = port:PH11<1><1><default><1> Compiled it again, copied it into /boot/script.bin, rebooted, nothing. Its the las…

Hello, I'm running a banana pro on the last armbian without any issues on a 16 gb SD Card. I wanted to make a try on a 64 gb card and burn the image on it, I think something went wrong, but now I cannot format or burn anything on the SD card, it says that the media is write protected. I tried to wipe out using parted or some tutos I saw creating an additional Registry key, but nothing worked ! Is my SD broken ? Thanks Greg

The topic is no longer new, but I have not found the reason and its solution! If you turn off the power (just pull out the wire) then you can get a non-working system. As I noticed, the files opened at the time of launch are broken. And some files such as /etc/boot/armbianEnv.txt in general, they are recorded with some kind of garbage!!! Because of this, your settings fly off! For example, I use ttys1 and this option is registered armbianEnv.txt , but after the power loss, there is just terrible garbage in this file, as if the memory dump fell there!!! For example, I still use dotnet, so it also breaks down and does not start anymore!! When y…

Hello, I have trouble with my SD Card - it goes in Read Only mode. What I have: I have Running System from the HDD (installed by nand-sata-install command) My Cubietruck is online for now, but I'm afraid do switch it off. I try to run dd command to make a backup of RO SD card and reuse image on a new SD card, but it does not succeed: # dd if=/dev/mmcblk0 bs=10M | gzip -c > /media/dataPartition/sdcard.img.gz dd: error reading '/dev/mmcblk0': Input/output error 0+0 records in 0+0 records out 0 bytes copied, 0.00503184 s, 0.0 kB/s I read the forum regarding backup and restore and my question is following: Is there is a way to …

Hello, I just received a replacement unit of my Lamobo-R1 board and I'd like to test it with an SD card I've currently running on a BananaPro with the latest Armbian release. Is there a way to use it on the Lamobo-R1 without having to reinstall & reconfigure everything? Thanks, V.

Hi, without consulting the specs first I bought a 128GByte card and obviously it doesn't work on my OPi Plus2e Is there any chance this will be fixed in software or is this a hardware limitation? Cheers, pansen

I have a Orange Pi Zero2W with Armbian. I flashed a SD-card, and then I copy the system and boot to a usb- hdd (sda) and the system boot to sda Want hdd because It write much data and USB 2 don't take mush more speed. But I get a warning about a file-error or something so I run fsck on sda(hdd) that was a systemdisk, but when I run I choose to do it read-only, but anyway it does not boot any more. I think I can take the usb-hdd and run fsck from another computer? I have one system with Ubuntu on a Intel 6 gen, and Raspberry pi 500 and 5. The Pi-machine have raspberry-pi OS and the other Ubuntu 24.04.Does the machine or system have any significa…

Hi, it ist well known, that a SD-card can be destroyed when you power-off a Raspberry-Pi without a shutdown. Does the same issue exist with an Orange-Pi (One) ? I want to use an Orange-Pi One headless and without SSH/TTY, only some sensors and LEDs are attached. Tnx L

Hi Armbians, I'm running two identical Cubietrucks with Armbian Jessie systems in headless (very lean) mode without any X-Windows or the like. Both boot from 16GB SD-Cards. Now one of them, which had encountered a number of power failures, suddenly ran out of space on the SD-Card (100% usage of / ), while the other CT only shows 22%. I ran across this phenomenon, when the system failed to carry out an apt-get update at one point and important services Samba were no longer started. I then searched the root filesystem for culprits but there was nothing suspicious ... So I thought there might be a partial "destruction" of the fil…

Is there anyone who familiar with H3's secure boot? I've got an ott box recently, with 1GB RAM, 8GB eMMC, H3 soc, wifi module is RTL8189FTV. I try to use sunxi's tools FEL to boot, but not succeed. But the nanopi-M1 board can be booted up with FEL. when change the u-boot-SPL's textbase, and set it to SRAM-C's space-0x10000. FEL can download the spl and execute it. The SPL init the DDR. Then download and execute u-boot. u-boot can run, but cannot reach cmdline. the datasheet shows that H3 support secure boot feature, but I can't find any documentation about this. Through the H3's SDK, I got some information about sbrom. I still wonder how to set the…

Hi, I use a armbian image from https://dl.armbian.com/bananapi/ for my bananapi. Are the private keys in /etc/ssh/ generated on first boot of my bananapi or are they in the image, so everyone with the same image got the same keys? Thanks!

Igor, Could you consider adding the security system patches for Allwinner.. or maybe as a configurable option? https://lkml.org/lkml/2015/5/14/278

Seems like it won't boot and stucks at: INFO: PMIC: DRAM voltage: 1.50V INFO: Continiously reboot. Can't understand why. Any advice?

I have gotten Oops a few times, now this morning I got it again I can see that is says "Segmentation Fault". I could still issue sudo armbianmonitor -u so I included those logs. Since I was also connected to both via SSH, where I was running "armbianmonitor -m" and logged in via serial I include the output of those windows below: SSH output: ... Time CPU load %cpu %sys %usr %nice %io %irq CPU C.St. 00:56:54: --- 0.00 0% 0% 0% 0% 0% 0% 40.1°C 0/15 00:57:00: --- 0.08 1% 1% 0% 0% 0% 0% 40.1°C 0/15 00:57:05: --- 0.07 1% 0% 0% 0% 0% 0% 40.1°C 0/15 00:57:10: --- 0.06 1% 1% 0% …

Hi, I'm struggling to find a solution. I installed heirloom-mailx following this site https://ubuntuforums.org/showthread.php?t=1711217. I can send emails (using gmail) as root user. The problem is with non-root user: the messages go to a query folder (/var/spool/mqueue) and never are sent. I have little experience with linux. Could you help me? System: Cubieboard 1 Armbian Legacy Jessie server 3.4.112 .mailrc set sendmail="/usr/bin/msmtp" set message-sendmail-extra-arguments="-a gmail" ======================================================================================== .msmtprc #Gmail account defaults logfile ~/msmtp.log account gmail auth on host smtp.gmail…

I am just getting started using the Orange Pi Zero and installed Xenial 4.10.1. Currently I am using Python and am able to address the GPIO pins (using this project: https://github.com/duxingkei33/orangepi_PC_gpio_pyH3) However, I need to communicate with a serial device (projector) using RS232 on 9600 BAUD. For this, the built-in UART should do the trick (with an additional voltage converter). Does anyone know how I can address this device from Python? Alternatively, is there a way to clock" an GPIO output to 9600 BAUD and manually send the data? Thanks, Ezpl

I have the temperature sensor DS18B20 connected to port 20 of the gpio as w1, if I want to connect another sensor it is as easy as adding a w2 and its port in /boot/bin/orangepiplus2e.bin [w1_para] w1_used = 1 gpio = 20 [w2_para] w2_used = 1 gpio = 10 or [w1_para] w1_used = 1 gpio = 20 gpio = 10 So or something else? thanks

I'm a newbie. Got the NanoPi R1 that sports a UART but no Video Output. Now when I want to read the output of the serial console I need a 3-wire cable and a converter, that much I know. But what is the baud rate? Where is this configured on the armbian NanoPiR1 image (on my raspberry Pi I just checked and found the file /boot/cmdline.txt with that settings, in my case it's 115200) Why is the baud rate nowhere documented? On the download page https://www.armbian.com/nanopi-r1/ it is stated that "serial console is enabled on UART1, which is exposed on chasis" , but no hint about which speed to use. There neither is any info about the baud rate on…

trying to read the serial data from the UART1 port then write it on the UART2 port .... this is absolutely easy in the case of just reading the serial data. but now what m really trying to do is to read the serial binary bits which includes the serial data and the framing data ( parity bit/stop bit/start bit) and then write all of these binary bits to the other serial port. how could this be done? how could i read the serial bits without the framing bits being stripped? thanks in advance best regards

my code works just fine when executed during ssh session on NANOPI NEO CORE (booted from emmc) ! when trying to make this code run automatically on startup which is something that i have done before, unexpected delay happens after 5 seconds of continuous taking data from mic to be sent on serial port ! could not figure out what is really going on ! does it differ in terms of configuration of the nanopi when logged in through ssh !? or is there some configurations that must be handle on startup scripting !?

Hi, I have Orange Pi Zero v1.5 with Armbian Buster (mainline kernel 5.4.y) and I would like to use the serial_rs485 struct from user-level. It is possible?

Hello I have problem with UART after some random time i have got serial8250_interrupt with dmesg log. After that my software reading/writing is broken from UART. [88124.598598] irq 42: nobody cared (try booting with the "irqpoll" option) [88124.598617] CPU: 0 PID: 10713 Comm: sas-statistics- Not tainted 5.3.7-sunxi #5.99.191031 [88124.598620] Hardware name: Allwinner sun8i Family [88124.598657] [<c010d751>] (unwind_backtrace) from [<c010a32d>] (show_stack+0x11/0x14) [88124.598674] [<c010a32d>] (show_stack) from [<c0923da9>] (dump_stack+0x69/0x78) [88124.598689] [<c0923da9>] (dump_stack) from [<c0164135>] (__report_bad_ir…

hey guys I ran some test with both version of OPI Win's Armbian and: I got all time reboot on server edition I see the the first Armbian boot up page but desktop wouldn't show up... please give me solutions. Thank you guys.

Hello, Is it possible to install serviio (armbian) ? Board: Orange pi One OS: Armbian - Ubuntu xenial 16.04

Hi, I'm trying use USB Audio card it's works fine in this cammand aplay -D hw:2,0 test.wav hardware Orange pi one version Armbian 5.11 root@orangepione:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: audiocodec [audiocodec], device 0: SUNXI-CODEC sndcodec-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: sndhdmi [sndhdmi], device 0: SUNXI-HDMIAUDIO sndhdmi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 2: Audio [USB Audio], device 0: USB Audio [USB Audio] Subdevices: 1/1 Subdevice #0: subdevice #0 use portaudio library and get this error root@orangepione:~/portaudio/bin# ./paex_sine PortAudio Test: output sine wave. SR…

Hello. I need to set a low level on a gpio pin PA6 on boot. I'm trying to do this through the device tree: /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { target = <&pio>; __overlay__ { pinctrl-0 = <&pull_pins>; pull_pins:pull_pins { pins = "PA6"; function = "gpio_out"; bias-disable; output-low; }; }; }; }; I need to set PA6 to low. After boot, I see my overlay in device tree, but the level on the PA6 is still high. I can easily control the level through libgpiod (gpioset gpiochip0 6=1 or gpioset gpiochip0 6=0), it works. But I ca…

Hi, back a again for a question. Got an 7" LCD Display connected to my pcDuino with Armbian (Kernel 4.x) and it displays nearly fine on HDMI. First i altered display resolution in /boot(boot.cmd) but i still got "cutted sides" of the display... On my Raspberry with Raspbian i had to alter /boot/config.txt with the foloowing content: # Pollin 7 Zoll Display hdmi_force_hotplug=1 framebuffer_width=1024 framebuffer_height=600 framebuffer_depth=24 hdmi_group=2 hdmi_mode=87 hdmi_cvt=1024 600 60 3 0 0 0 # Pollin Display Ende Where can i do that similar with armbian, think i have to change hdmi_group and hdmi_mode like i did with the raspberry, so that the LCD …

Hello everybody! I would like to make a home media server with my HDD connected to Banana Pi (on SATA). I want to run Torrent client with WebUI, dlna and VPN server thereon. I`m stucked with fstab file configuration. First I tried to format my HDD`s partition to NTFS, every permission was good, but Transmission download, and FSTP file download was incredibly slow (4MB/s, but I have gigabit internet connection). The fstab configuration was this: UUID=<the uuid of the ntfs partition> /mnt/DataHDD ntfs defaults,auto,umask=000,users,rw 0 0 I`ve readed that, ext4 filesystem can be faster, so I decided to format the partition to ext4. After that, I changed…

I use Armbian_4.3_wheezy on SD video with 1280x720p resolution. When I transfer to NAND, only with the resolution of 1028x1024p and can not adjust the resolution to 1280x720p. Already changed the script.bin file (via fex2bin), the uEnv.txt file (disp.screen0_output_mode = EDID: 1280x720p60) and not worked. How can I change the resolution to 1280x720p? Best Regards Marco Aurelio

Good day friends, For some time now I've been trying a DAC (dac-pcm5102mk-i2s) with the Orangepi Pc Plus OS "Debian Stretch with Armbian Linux 4.19.62-sunxi" to put into operation. Unfortunately without success so far. On another Orangepi Pc Plus with Ubuntu Xenial with Armbian Linux 3.4.113-sun8i I activated the DAC after the tutorial I2S on Orange Pi H3 Da Alchemist February 29, 2016. It works fine there. Debin strech does not have a script.bin that I could convert in order to be able to make the settings. I would be happy if someone could help me. Best regards Hans-Jürgen Grigoleit

So I'm pretty new at using serial ports in linux so not even sure if this is the right place. I'm playing around with MIDI using the serial ports on the Orange PiLite - it uses the baud rate of 31250 to achieve this you use setserial to get the base_baud (which it reports as 1500000) and you divide by the speed you want to get the divisor i.e. 1500000/31250 = 48 this becomes >setserial /dev/ttyS1 divisor 48 speed_cust So now when you use 38400 as your baud speed it actually becomes 31250.... ...in theory after some fiddling I found the divsor is actually 50 as 48 gives you weird results which would suggest that the base_baud is actually 1562…

Hello, please tell me how I can configure the processor on my Orange Pi Zero to the maximum frequency and voltage, as well as how to do SWAP and register it at startup, I use active cooling radiators and a cooler, I am warned of a possible failure, thank you in advance!

On a CB1.... cubie@cubieboard:~$ uname -a Linux cubieboard 4.5.2-sunxi #11 SMP Thu Apr 28 21:53:25 CEST 2016 armv7l GNU/Linux cubie@cubieboard:~$ lsb_release -a No LSB modules are available. Distributor ID: Debian Description: Debian GNU/Linux 8.4 (jessie) Release: 8.4 Codename: jessie cubie@cubieboard:~$ ... I'm trying to use the gpio pins I set up in script.bin with this configuration: No other peripherals are using those pins that are configured in my fex file. A scan of the DTS file also shows nothing using those pins. When I enable pin 1 via: the gpio1 device shows up. When I do the network interface stops communicating. The sy…

4.14.65-sunxi on an Orange Pi Zero. Trying to set the i2c bus speed to 400kHz using the following dts: /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { target = <&i2c0>; __overlay__ { clock-frequency = <400000>; }; }; }; Which produces: Error: dtc does not support compiling overlays Please try to install matching kernel headers Installed linux-headers-next-sunxi and still getting the same thing. Device tree compiler version: DTC 1.4.2. What am I doing wrong? Spoiler

Hello Guys. เว็บพนันบอลต่างประเทศ เว็บแทงบอลต่างประเทศ HowTo: Setting up resolution 1600x900 & 1366x768 ? &how can i set up other resolutions those are not in h3disp like 1600x900 board is orangepi-pc

Hello, I use the NanoPi Neo (4.19.38-sunxi, Armbian #5.85 ) to pool an external device over /dev/ttyS1 serial port. At flashing moment of the external device, I should switch pins of ttyS1 to input mode by using bash commands #!/bin/bash firmware=`ls update_*.hex` echo "198" > /sys/class/gpio/export echo "199" > /sys/class/gpio/export echo "in" > /sys/class/gpio/gpio198/direction echo "in" > /sys/class/gpio/gpio199/direction # device update flash -P linuxgpio -b 40000 $firmware echo "198" > /sys/class/gpio/unexport echo "199" > /sys/class/gpio/unexport Is it possible to change up the mode of pins to the alternate function (ALT5) without the r…

Hi to all! I'm taking my first steps with an Orange Pi PC+. Before I did projects with raspberry pi, but the extra functionality provided by emmc memory has made me decant for orange pi. So my problems are related to the compatibility of gpio functionality. I have two SPI devices (TFT and RFID reader), and I want use PA21 pin for SPI1_CS. I changed /boot/script.bin file for second SPI activate adding this lines: [spi1] spi_used = 1 spi_cs_bitmap = 1 spi_cs0 = port:PA21<2><1><default><default> spi_sclk = port:PA14<2><default><default><default> spi_mosi = port:PA15<2>…

Hi, Before I start, I want to thank the developers for making great products. I am fairly new to SBCs, but unlike the official images, Armbian works great on my OP plus 2E. I have recently bough a OP zero+ H5, but as it lacks ethernet, I can't set it up. Is there a way (like raspbian) to set up wifi on the sd card after i burn the image on to it?

I have a "Banana PRO" One USB disk, 2TB with three partitions in ext4, the first partition is mounted (hdb1), the other two are not mounted. One USB disk, 4TB with a single ext4 partition mounted (hdc1). One SATA SSD disk with a single ext4 partition unmounted (hda1). Several aesthetic considerations: After the upgrade, reboot and login, the welcome screen and 100% battery!!! Hurrah!!! It seems that the MMC is 9% occupancy and ... oh! my hdb disk has only one partition? ah no, only reads hdb1. And the other two disks? I have two mounted partitions but only shows one. Turn off the system with the poweroff order and boot from the power button again, the battery is down to…

Hello, I have a custom board with A20 and I like to share the UART7(I20/I21) pins. I mean sometimes used as UART and other times used as output ports. Should I always change the FEX file to use one u other functionality. The perfect way is using both option without restart the system. Thanks!

The MAC address of your wifi port on your Orange Pi Zero probably starts with C8:27:A7:F9:xx:xx I obsfucated the last 4 digits of mine. The Ethernet Port MAC starts with : de:ae:b8:d7:xx:xx I needed this when I was trying to find the device on my network to SSH in. root/1234 It showed up on my network as a reasonably "fast" device with 0ms lag. I'm running a Cat 6 network with a gigabit switch. A nice pinout that Linux34 from Orange Pi posted.

Hi there. I want to use a push button on a GPIO to shutdown O Pi Zero safely. Though the acpid way runs fine on an O Pi One, I wonder if there is a way to make it work on a O Pi Zero. Please direct me if its documented somewhere already. Thanks

Hi, I am trying to use an Orange Pi Zero as a headless music player running MPD connected to a USB DAC. I have everything set up and it works well, but now I would like to add a momentary push button connected to a gpio pin to enable me to soft shutdown the Orange Pi Zero. I've done the same with python scripts that I've found in the Rune Audio forum (which runs on Arch Linux) for the Raspberry Pi, but I understand that the Pi Zero pins are different from the Raspberry Pi. This is the script I used on the Raspberry Pi #!/usr/bin/env python2 import RPi.GPIO as GPIO import time import subprocess GPIO.setmode(GPIO.BOARD) #Select unused GPIO header pin…

I have two Orange PI +2E machines. The first one I got was a while ago so it's running a 3.4.113 kernel (16.04), the more recent one I purchased is running 4.19.13 kernel (18.04) - both are Ubuntu Armbian. I've noticed when I use the "shutdown now" command on the older pi, the board actually powers off but when I use the same command on the newer kernel board, it never powers down. The newer board appears to stop all services and eventually report that the system is halted but it remains in that state. Is there a way to enable it to power off after a "shutdown now" is issued? I'm wondering if this is a kernel difference but it may be something else completely. …

Sometimes it's unclear if my Nanopi NEO2 is still running, or fully locked up / FUBAR. Ping and SSH give no result. As there is no HDMI, I have no way to check if it's still there. So I was thinking: can I let the green LED flash each x seconds as a sign of life? Quote from Igor: "Both are accessible via sysfs, green is configurable while blue is not lit and reacting to anything. ". So a crontab script that writes something to /sys/ <LED> ... ? Feedback appreciated.

Hi Struggling here with Orange's GPIO so I would be glad to see any pointer to a working gpio example for 3.4.x kernel. Even a simple one pin state switching would be great. Christos

Maybe this is not strictly related to Orange Pi PC but a few weeks ago I had problems with booting my device - mainly OpenELEC and I had to debug it somehow using serial port and the terminal. Unfortunately my PC is rather far from the place where I keep OPiPC. So I was forced to prepare separate device - cheap STM32 MCU based terminal display with 2.2" LCD screen directly supplied from Orange Pi PC 3.3V. It can be used also with other devices which allow serial console debugging. Watch below videos for more details and the code: Maybe someone finds it useful.

I have an OrangePi Plus. I downloaded and installed "Armbian_5.25_Orangepiplus_Ubuntu_xenial_default_3.4.113.7z" (actually, I installed the image file from inside that archive) onto a micro-SD/TF card (16GB) and managed to get it to talk to my monitor (thanks, armbian, for "h3disp"). I searched the web, and this forum, for instructions on how to install a graphical desktop on top of the particular Ubuntu Xenial flavor and found nothing I could make sense of. I tried the following: sudo apt-get install xserver-xorg-video-fbdev ubuntu-desktop I got the Ubuntu greeter, but when I log in, I get a stock desktop background with no sidebars or menu bar. I can move the…

Hello fellow Sunxi forum members, Some may know me from previous Armbian adventures, primarily Orange Pi Zero 3... but I have jumped brands for a change of scenery (but not SoC). When researching H61X based boards for the Zero 2 and Zero 3 development we were doing in another thread, I found the Sipeed LonganPi 3H, which is a relatively new board that took a while to find. My first impressions are that is really well made, and packs a lot in to the Raspberry Pi Zero style profile (although it also has a daughter board). It was shipped quickly in a nice quality hard plastic storage case and.. best of all.. it has two hardware buttons.. so I can rese…

The distributions for this SBC don't boot due to errors to thermal device. I saw some messages in the forum where has be told that disabling thermal check the distribution works. Can you blacklist or disable thermal sensors check?

Hello and Happy New Year my lovely Armbian friends! I am aware that this topic is a reoccurring one, having abused the search function beyond its functional capabilities I have found the following threads that deal with somekind of sleep and wake with separate pins for each function: how to wake up OPi3 gpio to inform of system shutdown I would like to know if it is possible to have 1 pin act as both sleep and wake depending on its voltage? - if so how could i modify one of those dts in the first link? I am new to dts so not sure how the pin mappings are assigned. for example, I have a DRV5053 hall effect sensor tha…

Hi. I have an OPI PC with armbian jessie server. Is it there any way to automatic sleep usb hdd when it is a certain time idle?. Same disks in a RPI/RPI2 with raspbian goes to sleep after a period of inactivity.

Hi everyone, I have an orange pi pc+ (also a orange pi one) and i'm trying to use one of them as a wifi-wifi router. I've been able to do it work several times, with different wifi dongles, armbian versions (both debian and ubuntu legacy and mainline) but I always get low wifi speed in the AP interface. The problem is that the AP network through the orange pi always gives me around 30-10% of the full internet connection. That is, if my connection gives me 1.5mb/s, the client interface at orange pi gives around 1.5mb/s but at the AP interface is only 200-500 kb/s. I'm going to show here the last configuration I've tried. I would like to achieve a "decent" wifi…

I have a BananaPi running 4.2 (with Wheezy) and I am getting poor network speed. When testing download a file from the internet, I am averaging ~500k/s. I have another BananaPi running 3.4 (also with Wheezy) and on that board, I am averaging ~3MB/s downloading the same file from the same location. I tested this multiple times and the results are pretty much the same. Any idea why network performance is so poor on 4.2? Thanks.

Hi all, A week ago I started using the latest Armbian image (Legacy Desktop) for my Olinuxino A20L2. Since the switch from the Olinuxino A20 original image back to Armbian I noticed a lot of performance loss. Especially when surfing the web through Firefox on even simple pages is sometimes terribly slow. Anyone have an idea how to solve this?

Hi,I have a problem with the ssh wifi connection with the nanopi neo air it has every faith that I connect it is too slowI have disabled the NetworkManager with the following commandsSystemctl stop NetworkManager.serviceSystemctl disable NetworkManager.serviceAnd configured my network connection with the / etc / network / interfaces fileAnd also i have disabled iwconfigIwconfig wlan0 power offalways remains the problem of SSH slowthenks for your help

Old post below, here is what I found out thanks to some help from linux-sunxi IRC, I think this is a bug in the ondemand governor When using ASIX AX88772B USB to ethernet adapter and the cpu-governor is on ondemand, transfer speed is very slow. If governor is set to conservative or performance (yes that's right) speed is ok, 50 Mbit at least. So the problem has nothing to do with cpu speed as such (it's working @ steady 480Mhz and @ steady 1200Mhz) for now I'll stick with conservative as I don't want my board to burn up, but It would be nice if someone could take a look at that ondemand governor. Additional info: …

I am using a system I built from the trunk of Armbian for the pine64so. After booting up the mouse does not do "smooth mouse tracking". The movement of the mouse lags behind where it should be and has to "catch up" which takes several seconds. I consider it unusable doing this. This is Version "20.04.1 LTS (Focal Fossa)" Armbian 20.08.0-trunk Focal 5.7.17-sunxi64 #trunk Mon Aug 24 03:00:31 PDT 2020 aarch64

Hi, as the title says while building this image i had this console reported error: E: Unable to locate package mali-sunxi-utils Also i would like to ask if there is hw acceleration(gpu) on xenial desktop images Thanks

Hi there, I have 2 OPi PC+, one was with Jessie, then upgraded to Stretch, Working almost fine, only one issue was "systemctl start postgresql.service" not working. I used a workaround, "su - postgres -c 'pg_ctl start'". Postgres not from repo (previously was from repo) but compiled from source, as I need at least version 10 for "logical replication". Not at some point of time, I noticed message, that kernel package is to upgrade (3.4.112 to 3.4.113). After reboot graphics don't start. "No screens found". Ok, so I tried to upgrade (apt update, apt upgrade, apt dist-upgrade after changing name in /etc/apt/ files). Now it's almost crash: - graphics …

Hello, My project does not allow me to use SD card to boot and run my application. I can use SD card as drive to save my data. Is there any alternative way to do so ? Has anyone built a micro rootfs for O-Pi-ZERO NOR Flash ? Does anyone have an idea of the MINIMUM SIZE that is required to do so, if 2MB is too less ? Thanks Nbird.

Hello I want enable smb 2.1 on cubi plese help step by step and make error: root@cubietruck:/usr/src/linux-headers-4.2.3-sunxi# make scripts/kconfig/conf --silentoldconfig Kconfig CHK include/config/kernel.release CHK include/generated/uapi/linux/version.h CHK include/generated/utsrelease.h make[1]: *** No rule to make target 'arch/arm/tools/gen-mach-types', needed by 'include/generated/mach-types.h'. Stop. arch/arm/Makefile:305: recipe for target 'archprepare' failed make: *** [archprepare] Error 2 please help with step by step. Gabor Sneff

I am trying to start snap multipass on the device nanopi k1 plus, getting the following error: root@nanopik1plus:~/testSnap# multipass start launch failed: Internal error: qemu-system-x86_64 failed getting vmstate (Process returned exit code: 1) with output: qemu-system-aarch64: -nographic: No machine specified, and there is no default Use -machine help to list supported machines

Hi. Any idea about including snappy ubuntu core in the build process?

SND_USB_AUDIO seems now disabled in Vanilla Kernel. Probably after this commit: - https://github.com/igorpecovnik/lib/commit/70231cf8ae641650ec8601124db33b5b186a285b This should be why my USB dac doesn't work anymore after an update of the system. Is there any reason or it's only an error? I must thank you Igor for your work.

Hello ! I have a problem with an OrangePi Zero under Armbian Buster with mainline kernel (5.8). I need to put the module snd-aloop as primary soundcard (index=0), and the integrated soundcard sun4i-codec as index=1. It worked very well with kernel 5.4 and before. I just had to load the snd-aloop module by adding it to /etc/modules and add "options snd-aloop index=0" to /etc/modprobe.d/alsa.conf. But now this is impossible, snd-aloop doesn't load. I had this message when I try to load it manually : modprobe: ERROR: could not insert 'snd_aloop': No such device After reading configuration file of the kernel, I saw that the module sun4i-codec (integrat…

Hi, seems after some system updates SNMP stop reporting data about storage (size/used). It happen on 2x Orange PI One and on one Orange PI PC2. Actually in monitor what I use for SNMP monitoring I see last valid data was there at 05/09. I think at this time I update all boards and as I remmember there was also some update for snmpd. Can anyone confirm this problem ? And when we talk about SNMP, what is best way to change default logging level for SNMP ? Seems changing in /etc/default/snmpd doesnt have effect and after last update I must again edit files in /lib/systemd to stop that annoying flood in log from SNMP. OPI PC2 - 4.…

There is no one who has to compile the 2.9.8.3 version of snort? Thank you

I have an Orange Pi One Plus with the H6 chip in it and I'm quite happy with how well it's supported by Armbian. I haven't really had any problems with it. I do have one question, though. I'm using armbianmonitor to "-m" monitor the machine and I notice that the temps are always pretty hot. Even at idle (480MHz) it still shows 72C. That seems higher than I would have expected. Is this normal, expected behavior? I understand that the SoC thermal monitoring code in the kernel is pretty new and therefore might not be perfect, yet. So, I thought I'd ask. Because it may just be my board that's off. Does anyone know if this is normal? Info: …

Hi, Is there any sleep or low power modes in orange pi with soft wakeup I want to wake up Orange pi zero at some specific time. For that i go through some forums and searched alot about that but could not found any way to do this. I also go through some 'rtcwake' commands but they didn't work. Any Idea regarding sleep modes and how to wake up would be great help for me. Thanks,

Hello I was wondering how can make possible usage of software raid1, using integrated emmc and another card placed into the slot. So far I have used that on Slackware x86 without any issue, but there I tells the Lilo to boot from /dev/md0 for example. Wonder where I should make adjustments here (in Armbian(. Can someone point me at the right direction?

Dear all as title, the orange pi r1 can use to bridge mode ? and how to do ? like this

Doohh ... User error - 1PPS wasn't enabled on the GPS. The OPIO Kernel works fine w. 1-PPS $ sudo ppstest /dev/pps0 trying PPS source "/dev/pps0" found PPS source "/dev/pps0" ok, found 1 source(s), now start fetching data... source 0 - assert 1524154630.697340907, sequence: 6793 - clear 0.000000000, sequence: 0 source 0 - assert 1524154631.697261112, sequence: 6794 - clear 0.000000000, sequence: 0 source 0 - assert 1524154632.697166525, sequence: 6795 - clear 0.000000000, sequence: 0 source 0 - assert 1524154633.697084896, sequence: 6796 - clear 0.000000000, sequence: 0 source 0 - assert 1524154634.697017267, sequence: 6797 - clear 0.000000000, sequence: …

Hi Guyzz Just got a OPI1 (H3 512MB), and was trying out the stretch image from here https://www.armbian.com/orange-pi-one/ https://dl.armbian.com/orangepione/Debian_stretch_next.7z It won't boot It starts up , w. both Orange & Green leds on lan , then i can see it requests a dhcp address , and it gets one (req/offer runs many times), then nothing happens after that. Just - Green light blinks on lan , Orange is unlit. I tried to write (linux dd) it on 2 different SD-cards , a 8GB Intenso , and also a 16GB Sandisk - same behaviour. I grabbed the latest Jessie from the archive , and wrote it to the Intenso 8GB , and it booted fine w. jessie. I don't mind…

Hello! Since I upgraded to 5.35 on my OPI PC Plus the connected TV-Screen (direct via HDMI Cable) ist purple. An upgrade zu 5.36 has the same problem. When I connect the OPI to a Standard PC Monitor via HDMI there is all ok. It would be nice if there has anyone a solution for this.. thanks SOLUTION: I downloaded a new version of 5.35 and upgraded to 5.36 Then I copied the files in /boot of the SD-Card (New One) to the /boot of the OLD system on EMMC - and it works

Hi, I have installed Wheesy 3.4.108 on my Banana Pro. connected to it using SSH from xterm on my linux box, did various housekeeping, set up user squeeze Installed logitech media server works OK Installled Squeezelite ---- needed to set up alsa, ran sudo alsamixer, Alsamixer ran OK but when I hit Fkeys on host machine to select various alsa menus, alsamixer terminates and drops back to Banana pro CLI, obviosly F key keybindings are not what alsamixer expects. Fails under both xterm and putty and on two linux host systems. What do I do to make banana pro use the Function keys F1-F6 to work as alsa requires? I note that there are lots of…

Greetings all, See my last post in thread for method I found to get around issues. EDIT: This may be limited to is an apt issue DNS seems ok after all. Use nmtui to edit network config not armbian-config None of what follows should be taken as complaining. I am only trying to get some help, give some observations from a non-expert viewpoint and possibly help ID a bug. Not being an expert, I am looking for confirmation. I am trying to get the NanoPi NEO core-2 LTS set up and am having some issues with apt. I haven't gone past that because the first thing after getting properly booting install (for me anyway) is to install webmin…

Hey there,I am having trouble with SPI on my Banana Pro. I am trying to access the SPI interface via WiringPI (the Lemaker Banana Pro version). But whenever I try to access it, it tells me: Unable to open SPI device: No such file or directory The message is correct, as there are no /dev/spi* files present. The question is: How do I get them?(according to http://linux-sunxi.org/Linux_mainlining_effort#Status_Matrix it should be available since 3.15)For the 3.4.x, one had to load modules (spidev, etc.) but this doesn't seem to work for 4.9.x. There is a 'spidev' module which loads fine (according to lsmod) but with no recognizable…

HI, guys! I tried to enable spi connect RC522 on OPi_PC(H3). It works! my topic: but now, I make the same way to enable spi with RC522 on OPi_PC2(H5). I can found spi on "/dev/spidev0.0" But when I run "Read.py" script as root. It can't detect & read the cards. How can i use it on OPi_PC2?

Kinh nghiệm mở shop đồ chơi trẻ em? Đồ chơi trẻ em là luôn luôn cần thiết và là sở thích tất yếu của con trẻ ,giúp con trẻ phát triển các kỹ năng trí tuệ toàn diện, nhất là những sản phẩm mang tính giáo dục. Các bậc phụ huynh ngày càng có nhu cầu cao về những sản phẩm, đồ chơi an toàn cho con,, giúp con phát triển về tinh thần, trí tuệ và thể lực. Chính vì lẽ đó mà cửa hàng đồ chơi đã ra đời và thu hút nhiều khách hàng. Đầu tiên để kinh doanh thì bất kì mặt hàng nào chúng ta cần có nguồn vốn ổn định và đồ chơi trẻ em thì cũng không ngoại lệ. Nếu bạn cảm thấy thiếu vốn thì có thể Vay tin chap tại các ngân hàng, lãi suất cũng rất thấp. Bạn phải dự tr…

Is there currently a known problem with some of the Repos used by H3 Armbian Mainline (OrangePi Plus 2). For the last few days, when I run apt update, I get timeout messages on some repos. The repos that are consistently timing out are: http://ports.ubuntu.com xenial InRelease http://ports.ubuntu.com xenial-updates InRelease http://ports.ubuntu.com xenial-updates/main armhf Packages Additionally, this Repo sometimes times out, and sometimes succeeds, but takes a long time: https://deb.nodesource.com/node_6.x xenial InRelease Please let me know if you require more info. Many thanks, Roy Gilby

I'm having trouble installing asterisk in this version , in versions 4.4 and 4.5 of ARMBIAN Debian 4.4.3 Jessie worked perfectly! It seems that the error is related to kernel , but I'm learning to work with embedded now ! If anyone has experience with Asterisk and can help me I appreciate the support !

I have tested with two SDs - the same result. But vanilla works perfect! Strange is that after dd command I can't mount SDs with legacy, but vanilla I can. I've downloaded legacy twice.

Thu Jan 24 21:01:03 2019 daemon.info dnsmasq-dhcp[1726]: DHCPREQUEST(br-lan) 192.168.1.124 02:02:04:01:61:60 Thu Jan 24 21:01:03 2019 daemon.info dnsmasq-dhcp[1726]: DHCPACK(br-lan) 192.168.1.124 02:02:04:01:61:60 volumio Thu Jan 24 21:01:03 2019 daemon.info dnsmasq-dhcp[1726]: DHCPDECLINE(br-lan) 192.168.1.124 02:02:04:01:61:60 Thu Jan 24 21:01:03 2019 daemon.info dnsmasq-dhcp[1726]: DHCPDISCOVER(br-lan) 192.168.1.124 02:02:04:01:61:60 Thu Jan 24 21:01:03 2019 daemon.info dnsmasq-dhcp[1726]: DHCPOFFER(br-lan) 192.168.1.124 02:02:04:01:61:60 Thu Jan 24 21:01:03 2019 daemon.info dnsmasq-dhcp[1726]: DHCPREQUEST(br-lan) 192.168.1.124 02:02:04:01:61:60 Thu Jan 24 21:01:03 201…

I usually build a new armbian full os image, apply some kernel options and have no problems booting a sopine64. The last known good version for me was: Armbian 5.51 / Kernel 4.14.54 The latest (and starting with 5.57) with Kernel 4.17.16 only seem to 'half boot' - they start up uboot but fail to load the OS and instead attempt to do a network boot over TFTP. The errors go by so fast that I can't really read it and have to resort to trying to video capture it and the monitor seems to be slow to initialize and i only see the tail end of the errors scroll by. I am sure a lot changed between 5.51 and 5.57 - I noticed a new…

Hello, After I run apt-get update and upgrade, I lose the sound card: aplay -l aplay: device_list:268: no soundcards found... If I check my upgrade history, I can see the following: cat /var/log/apt/history.log Start-Date: 2018-03-16 22:33:12 Commandline: apt-get upgrade Upgrade: libgssapi-krb5-2:armhf (1.12.1+dfsg-19+deb8u2, 1.12.1+dfsg-19+deb8u4), tzdata:armhf (2017b-0+deb8u1, 2018c-0+deb8u1), ncurses-term:armhf (5.9+20140913-1, 5.9+20140913-1+deb8u2), libkrb5-3:armhf (1.12.1+dfsg-19+deb8u2, 1.12.1+dfsg-19+deb8u4), libk5crypto3:armhf (1.12.1+dfsg-19+deb8u2, 1.12.1+dfsg-19+deb8u4), linux-image-next-sunxi:armhf (5.34, 5.…

Hi all! After upgrading to 6.1.24-sunxi64 on my Orange Pi 3 LTS I lost sound at the audio output. dmesg shows this: platform sound_ac200: deferred probe pending I am a newbie to linux - can you, please, provide me a hint how to install the sound card back or revert to the older kernel with a working sound? Thank you!

Good day, We use NanoPi Neo Core in voice information systems. We found a problem with the implementation of Dynamic Audio Power Management for Portable Devices in H3. Our program plays voice files using the standard call of the operating system - "aplay". Before starting the reproduction of each file the voltage is discharged and restored at the output of the DAC. This leads to a loud click on the output of the audio system. Setting pmdown_time = -1 does not save the situation. Can you help in solving this problem? P.S. This problem appeared in version 4 of the kernel.

Good evening. I am preparing an Orange PI Plus 2 in order to be the first computer for my 8 years old son. The idea is that he could learn Scratch by watching some video tutorials in YouTube The problem is that actually, if you pause a video, and the you want for it to restart, only video does it. Sound doesn't starts again.It remains muted. Then, if you click to watch another video, sound come back. But you loose it again if this second video is also paused. It's a bit annoying. Do you have the same issue ? Best regard. Maesstrissimo.