Allwinner sunxi

Don't quite know what to expect here. The download page implies that there should be a gadget serial connection but there is nothing. I don't even see the USB DRC getting registered. Is this a known issue and is there a solution? TAIA. # nanopineo:~$ uname -a Linux nanopineo 4.11.3-sun8i #3 SMP Wed Jun 7 13:28:34 CEST 2017 armv7l armv7l armv7l GNU/Linux # nanopineo:~$ lsusb -t /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=ehci-platform/1p, 480M # nanopineo:~$ lsmod Module Size Used by evdev 20480 1 brcmfmac 172032 0 brcmutil …

Hello, can somebody from developers add next to KERNEL_TARGET for Orange Pi Lite in the build system please ? Regards

Hello people, I'm using Armbian 5.30 - kernel 3.4.113 on a Nanopi NEO. and I'm relatively new to this stuff, so please bear with me. I successfully managed to install an LCD screen on SPI (ILI9341) using this command: sudo modprobe fbtft_device custom name=fb_ili9341 gpios=reset:1,dc:201,led:6 speed=16000000 rotate=90 bgr=1 So far so good, but the resolution of the screen is too little and can't load anything - for example Dosbox. I would want to replicate the trick that already exists on Raspberry/Raspbian, and that is to framebuffer a higher res screen (at least 640x480) on the tiny LCD's resolution of 320x240. This is the p…

Hi all Im just got to play with orangepi plus 2e with armbian. but i encounter allow of system hang after few hrs of usage. anyone encounter this? Current Arambian verison- OS: Ubuntu 16.04.3 LTS Kernel: 3.4113-sun8i Frimware: #8 Boot and storage: EMMC Desktop: Yes service/application install- Gparted Octoprint MJPG-Streamer thanks alot

Hi, during the spring I used h3disp - 720p50 -c 1 (on 5.24 with sunxi-tools 1.4.2) to change the resolution for my desktop but today when I did a clean install (armbian 5.30 Jessie Default) I get Unsupported board/kernel combination: Orange Pi Zero running 3.4.113-sun8i. Exiting Is there still a way to change the resolution (720x576 is too low for the gui app I need to run)? Thanks in advance! Nicke

Hello, I run Debian/Jessie on a bananapi pro. The board suddenly stopped working completely. When I plug the power supply, the red led shows up (not blinking) and nothing more, no sign of activity at all, like on screen (hdmi). It is very surprising as it has been running very well for two years now, with a 5V/3A power supply and a sandisk SD card (like those advised). I checked that the sd card runs well on my laptop, the filesystem was not broken and no sign of corruption so far, especially in the /boot directory, no changes made lastly in this directory : latest modification dater are a few months ago. …

Hello, I'm trying to get an "Orange Pi Zero" running with Wifi and OV534 (Sony PS3 Webcam). I can't get both running at once. My attempts so far: Armbian_5.30_Orangepizero_Ubuntu_xenial_default_3.4.113: Wifi ok, no ov534 Armbian_5.30_Orangepizero_Ubuntu_xenial_dev_4.11.3: No Wifi, ov534 ok Armbian_5.32.170912_Orangepizero_Ubuntu_xenial_dev_4.11.12: No Wifi, ov534 ok I've read about XR819 on github posts (to use under 4.11), but I couldn't load it, there are three module files for this module: fw_xr819, boot_xr819 and sdd_xr819, but none of these is loading successfully: modprobe: FATAL: Module xr819 not found in directory /lib/modules/4.11.3-sun…

Greetings, I've got 2 M1 boards in front of me. The FA is running their latest distribution: http://www.mediafire.com/file/kc44mm1mdahslho/nanopi-m1_debian-jessie_4.11.2_20170905.img.zip By default the device tree for the FA has the USB controller (usb@01c19000) marked as disabled and is missing the dr_mode = "OTG" attribute. Enable the controller and Add the dr_node property and the board comes up as a mass storage device in both Windows and Linux. The board running Armbian has exactly the same device tree entries, dmesg shows the USB controller is loaded and visible with lsusb -t. When a gadget module is loaded all appears to work on…

I don't know if this is something I have broken or not, but I have a \var\log and a \var\log.hdd both identical and both being updated. Where should I be looking to rectify this duplication? ARMBIAN 5.25 stable Debian GNU/Linux 8 (jessie) 3.4.113-sun8i OrangePiZero

Hello Everyone , Can anyone please guide me . I need to use nano pi neo's USB pins(2.54mm x 2 header pins) and looking for resources related to it. I am using armbian OS on it. I am struggling with it , I read many resources on the web but none of them provide detailed information. Any help will really be appreciated !! Thanks so much!!

Hi, when I connect my external HDD - an Icy Box IB-RD2253-U31 (http://www.raidsonic.de/products/external_cases/soho_raid/index_en.php?we_objectID=3239) - to my Bananapi M1, running ARMBIAN 5.31 (stable Debian GNU/Linux 8 (jessie) 4.11.6-sunxi) the hard disk is not found. This is regardless of the HDD setup chosen, at least I tried with the two disks inside configured as JBOD as well as RAID1. After connecting the USB HDD, dmesg doesnt show any output, lsblk doesnt show it. Is there anything I can do about it to get it working, is it a firmware issue?

Hi everybody, I work on my Orange Pi Plus 2 since a few days now. I've installed Armbian with linux Kernel 3.4 (Debian Jessie) on eMMC. One of my main objectives is to bond the WiFi and the Ethernet interfaces in one interface called bond0 (I've seen many examples on how to do this on the Internet). My configuration seems to be good (it's based on the default interfaces.bonding file, just changed it with my WiFi parameters). When I restart networking service, none of my interfaces get up. I've tried to update/upgrade my stystem, reinstall ifenslave. I've also checked module list with lsmod, it returns a lot of names, but not "bonding" module. …

So far I was used to the Grub (and lilo) boot manager(s) but the Armbian 5.31 Bananapi Debian jessie next 4.11.5 image does some things differently. I have found the file /boot/armbianEnv.txt but none of the websites I found described what I should do with it. I tried to copy it to /etc but the changes did not take effect. I would like to remove the logo and have verbose boot messages. Could somebody help me to get there, please?

[Apologies. There seem to be a number of posting close to this subject. Trying to get a definitive view] So, with the 3.4.113 kernel the gc2035 driver fails when trying to identify the sensor. The problem lies in the sensor_init function where a read of the I2C/CCI bus fails. Before I break out the breakout board can anyone verify these basics please? I've tried the various suggestions for setting one of the GPIO pins prior to loading the modules but to no avail. Cable, blue insulation on top side of the expansion board FPC, blue insulation facing up towards SD card on the OPI one. FEX as below. [csi0] vip_used = 1 vip…

Hi! Thanks for your great job. I compiled Armbian_5.32_Orangepizeroplus2-h5_Debian_stretch_dev_4.13.0.img with your building script from git, which included last kernel with Orange Pi zero+ H5 support. Pluged uart-adapter for control booting process. U-Boot SPL 2017.09-rc4-armbian (Sep 05 2017 - 11:03:34) DRAM: 512 MiB Trying to boot from MMC1 NOTICE: BL3-1: Running on H5 (1718) in SRAM A2 (@0x44000) NOTICE: Configuring SPC Controller NOTICE: BL3-1: v1.0(debug):aa75c8d NOTICE: BL3-1: Built : 11:03:29, Sep 5 2017 INFO: BL3-1: Initializing runtime services INFO: BL3-1: Preparing for EL3 exit to normal world INFO: BL3-1: Next image address: 0x4…

Hello, i have some troubles with analog out of my Orange Pi PC. I thought i have the right cable which is assembled similar to this way: or more like this: But i almost break my device plugin it. This what have to be right channel (red) and pin 2 in the first picture, is shorted with pin 1 to GND when plugged. This confuse me a little, because the other way have to be similar to this: So before i resolder it this way, if anyone knows the correct order of jack pins, or have the right cable and can measure it, please let me know.

Hi, In the recent builds (5.32) noticed an annoying ..feature. When shutting down from desktop, it asks for password, whereas that was not been asked in prior versions. Build image is OPiPC legacy Ubuntu desktop. Can we revert it back to not asking for password when shutdown/reboot from desktop?

Hello, I have a couple of NEO Pi Air's and they show up as the same device in LightBlue. After a bit of digging, I noticed that the BD addr of the devices are the same. hci0: Type: BR/EDR Bus: UART BD Address: 43:29:B1:55:01:01 ACL MTU: 1021:8 SCO MTU: 64:1 UP RUNNING RX bytes:6552 acl:180 sco:0 events:373 errors:0 TX bytes:6809 acl:180 sco:0 commands:248 errors:0 Is there any way to change the address?

------------------------------------------------ **** RESOLVED **** ---------------------------------------------------- 20 years of experience in computer science and I look like an idiot front of my OrangePI PC... You want to have a working HDMI LCD SCREEN with your ORANGEPI PC and you want to learn fast… Read this small tutorial, sorry my english it not perfect and if I make some error during this tutorial, please admin just correct me inside the post. First of all, if you think you know something when you receive your orangepi haha, clear your memory my friend, orangepi is not a pc … is not a RASPBERRY so don’t try RASPBERRY tutorial …

Hello, I recently purchased a Banana Pi M2, and downloaded the latest desktop image to my SanDisk 32gb MicroSD card. Everything boots-up. However, the only interface that seems to be able to get onto the internet properly is wlan0 (Wireless). Ethernet, regardless of DHCP (registers properly) or Static does not seem to route properly. For example, I am not able to ping or SSH the device from another PC, and the Pi (itself) cannot ping/access any local IPv4 address as well. Internet access fails, and points to DNS not working properly (even though servers are specified). Tried many different methods, including taking management/control away from "NetworkManager", but …

I've updated to the latest kernel code, rebuilt and I I can now see /dev/video when I call "modprobe ov5640; modprobe vfe_v4l2" after booting into the nanopi. However, when I run the following ffmpeg -re -i /dev/video0 -c:v libx265 -preset ultrafast -x265-params crf=23 -f h264 ./out.mp4 I get the following error error [video4linux2,v4l2 @ 0x1a9a7f0] Dequeued v4l2 buffer contains 40960 bytes, but 38016 were expected. Flags: 0x00000001. The video format is yuv420p, 176x144, so it should be 176*144*1.5 bytes = 38016bytes. However the buffer seems to be slightly larger. I have written a few small c program…

Hi, I always have a boot problem with the OP lite after operating approximately for 2 weeks !! When the problem occurs, I got the following message while the system is booting : U-Boot SPL 2017.01-armbian (Feb 02 2017 - 02:58:38) DRAM: 512 MiB Trying to boot from MMC1 U-Boot 2017.01-armbian (Feb 02 2017 - 02:58:38 +0100) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi Lite DRAM: 512 MiB MMC: SUNXI SD/MMC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 6944 bytes read in 136 ms (49.8 KiB/s) switch to partitions #0, OK…

Friends I have a keyboard Rii i8 + I put the adapter that comes with the keyboard I put to locate by the bluetooth of the armbian it finds but at the time of pairing in happens nothing, only blinks green in Bluetooth and nothing else. I've tried another adapter, but it does not even appear as installed. This keyboard I use it with Openelec and works perfectly. Does anyone have any tips on what I can do for it to work on Armbian? Thanks.

I am using GPIO(CON3) pins 8 and 10 for a project. In BPI M1+, functions for those pins are PH0 and PH1 respectively. https://bananapi.gitbooks.io/bpi-m1-bpi-m1-plus-/content/en/bpi-m1+_gpio_pin_define.html But, when I added overlays=uart3 ,I didn't work properly . When I checked the overlay file sun7i-a20-uart3.dtbo , by changing it to .dts , I figured out that this overlay file uses PG6,PG7 pins, not PH0,PH1 pins. So, to modify the configurations without adding uart3 overlay in the /boot/armbianEnv.txt file, I wanted to edit the /boot/dtb/sun7i-a20-bananapi-m1-plus.dtb file. When I check the file, there are uart3_pins_a option and uart3_pins …

Hello, I want to provide support for IR infrared remote Shield V1.0 for orange pi zero and I need some help to know how to proceed. http://www.ebay.com/itm/IR-infrared-remote-Shield-V1-0-expansion-Transceivers-Module-for-Raspberry-pi-B-/291205297766 Signal RPi_connector(P4)Button1 -> Pin13Button2 -> Pin15IR_IN -> Pin11IR_OUT -> Pin12 Hardware Details: Hardware: Orange Pi Zero 512 IR Remote shield v1.0 connected to 2x13 Header OS: Armbian Mainline (Ubuntu_xenial_dev_4.11.7), This is mandatory for me as I want docker support. I have started reading Device Tree overl…

· Hello, So I tried to figure out the original dtb file used but the system by default when I boot the image without any fine configuration. But I couldn't find any information about the default dtb. I checked at /boot/boot.cmd , but nothing is mentioned for "setenv fdtfile" which was available in the old kernel. I figured out that I can add a suitable .dtb in the /boot/armbianEnv.txt in the following post. https://forum.armbian.com/index.php?/topic/4817-banana-pi-m1-extra-configuration/ fdtfile=sun7i-a20-bananapi-m1-plus.dtb But there is no way to know which .dtb file is used when this information is not set. Can somebody let …

Hello everybody, I'm pretty new to Armbian and H3 boards. I own an Orange PI + 2 board brought more than 1 year ago, yesterday I started to play around with it and I've discovered that for some reason its Mali GPU doesn't support OpenGL ES and it's somehow related to it having 2 GB of RAM on board. I'm really not sure how it can be related, but that's what Armbian's changelog for v5.20 says: Later in v5.25 it says: So I just want to know if 2GB boards feature OpenGL ES support (as well as HW video decoding etc)? I tried to run glxheads, glxgears etc from mesa-utils package, but got some really poor FPS there + some games I used for …

I installed the experimental version of the NanoPi Neo Air distribution on my Air a month or two ago. At the time I believe Bluetooth was not working on that version. I don't see any indication that it is not working now, but it doesn't seem to be working on my install. Is Bluetooth working on the experimental kernel? If so, should I just re-install, or is it not hard to get it working on an existing install? I just installed the latest updates and rebooted, and that didn't fix it. The symptom that I'm seeing is that if I run bluetoothctl it prints a prompt, but seems to lock up.

I just did an apt-get update on the mainline version of armbian and now the machine won't boot. I'l looking at the uboot output and it appears not to load the full kernel in and boot it. The strange thing is it seems to hang, but when I unplug the power, the kernel load info shows up on the serial output. U-Boot SPL 2017.03-armbian (Mar 15 2017 - 06:57) DRAM: 512 MiB Trying to boot from MMC1 U-Boot 2017.03-armbian (Mar 15 2017 - 06:571 +0100) Allwinner Technology CPU: Allwier H3 (SUN8I 1680) Model: Xunlong Orange Pi Zero DRAM: 512 MiB MMC: SUNXI SD/MMC0 *** Warning - bad CRC, usig default environment r serialial Net: phy interface0 eth0: ethernet@1…

Hello, all. My Orange Pi PC2 recently broke when doing an upgrade. So I hooked a serial cable to it and watched what it did. The error was that it couldn't find the dtb file. It was looking for "/boot/dtb/allwinner/allwinner/sun50i-h5-orangepi-pc2.dtb" and "/dtb/allwinner/allwinner/sun50i-h5-orangepi-pc2.dtb", but the former fails because the file is at "/boot/dtb/allwinner/sun50i-h5-orangepi-pc2.dtb". So, I put a simlink in dtb/allwinner called 'allwinner' and pointing to the parent directory. Now the device boots. I'm not sure if that's the proper fix, but it works for now and I'll fix it if I manage to break something with it later on. Thi…

Hello! Explain to me please, what's the problem with support for H5 processors? Drivers located here: https://developer.arm.com/products/software/mali-drivers/user-space , and here: https://developer.arm.com/products/software/mali-drivers/utgard-kernel , not enough?

I am using Orange Pi Zero Plus(http://www.orangepi.org/OrangePiZeroPlus/), but there's no armbian for it. I download armbian for Orange Pi PC2(here) and it works! However, PC2 does not have on-board wifi, so my zero plus cannot find a wlan device. The onboard wifi of zero plus is Realtek RTL8189FTV, and the driver source seems to be this I compile it on my orange pi and add "modprobe mac80211" before "insmod", it is loaded but there is still no wlan0 device So what should I do to enable wifi?

Hi All, I try to get a web page accessible from a hotspot with a notification sent to customer when it connects to the AP (using lighttpd, hostapd, dnsmasq, squid and squidguard) I can connect to the AP but I have no response to the ping On the Nano Pi Air in AP mode : iwconfig => wlan0 IEEE 802.11 ESSID:"Armbian" ifconfig => inet addr:192.168.101.1 I must be able to switch between modes with my software so I use scripts : To switch in AP mode => pkill -f 'ifup .*wlan0'; ifdown wlan0 ifdown wlan0 /bin/systemctl stop NetworkManager && /bin/systemctl disable NetworkManager && kill $(c…

Hi, I'm using my NanoPi NeoAir as a bluetooth streaming sink and as a webserver for several configurations and monitoring of the device. Bluetooth works fine as long as I don't disable the powersafe mode of wifi. Even in powersafe mode the bluetooth performance is not the best. If I disable wifi at all the bluetooth performance is great. My system is: Ubuntu 16.04.3 LTS 4.11.2 iwconfig: wlan0 IEEE 802.11 ESSID:"Teebeutel" Mode:Managed Frequency:2.412 GHz Access Point: 2C:41:38:FB:D7:30 Bit Rate=54 Mb/s Tx-Power=31 dBm Retry short limit:7 RTS thr:off Fragment thr:off…

Very grateful to armbian to provide such a good image！ Armbian has released many images that have been packaged with OMV。 I am follow this link for a long time：http://kaiser-edv.de/tmp/NumpU8/ I'm happy to see more and more mirrors available。 I used one of the images named OMV_3_0_72_Orangepiplus2e_3.4.113.7z and it works good，Special thanks to tkaiser！ There is another model（Orangepiplus2） that is better suited for NAS Because it has a sata interface https://www.armbian.com/orange-pi-plus-2/ Can Armbian provide OMV images of the above motherboards? At last, sorry for my poor English.

Hi, I performed an apt-get upgrade on my system, and it installed the 4.13 kernel. After the reboot, i started getting the message "bad CRC - using default environment". I spent the whole day reading many threads but still didn't manage to come with a solution. I tried the symlink to /boot/dtb/allwinner from the PC2 forum, but with no luck. I bought this board recently, it is my first board and i am very new to this, although i have decent Linux knowledge. Could you point out what i might have done wrong or if i'm missing something?

Hey all Testing with an Orange Pi Zero with mainline kernel. I've just noticed that none of the usb devices show up which are connected to the pin-header usb ports Is there any quick fix for this? e.g. enabling something somewhere? i think i remember maybe enabling something before to use these ports but i can't quite remember now. checking armbian-config thank you elliot

Hi, Got an issue with some long latency/buffer on OrangePiPC. Legacy built kernel with RT (Armbian 5.32). The default output, Audiocodec Analog Stereo, exhibits a latency of about 500ms or somewhere there, it is actually a delayed play. Other outputs do not have such latency, eg if I connect a USB audio device, it is just fine with only a few ms of latency. If it was a generic setting that would have impact on the USB audio too, but it is not, USB audio plays without excessive latency. Tried to set as low as I could the default-fragments (=8) and default-fragment-size-msec (=3) in /etc/pulse/daemon.conf to have 24msec of buffer but to no a…

Hi, i switched from Bananian Linux to Armbian xenial due to reaching its "end of life". Everything is working except it wont power off the system after a shutdown neither will it reboot properly. Hope someone could help me?

Hi all. I followed this tutorial and I got the AP and client mode working. wlan0 using the onboard wifi as the AP and wlan1 using a usb dongle as the client connecting to my wifi network. But when I connect to the PI and got an IP address via dnsmasq I am not able to get to the pi its self. I can not access anything on the PI. I have a web server running on it. How do I get to the services on the Pi it self via the AP I created. Basically what I want to do is have the client connect to the wifi network if there is one or if the pi is in range of the wifi network. But then if there is no network then I want to connect to the…

anyone know if the onboard mic works in armbian? ive tried using arecord on the default audio device but no output.

Hello so i got Orange Pi PC 2 today and installed armbian from here : https://www.armbian.com/orange-pi-pc2/ i can SSH to it. but i dont know how to get AV out to work :/ can u help me ? im a total Beginner i just need to get Tv out to work and start learning. I know that armbian for H5 is in the early development state.

Hi, I can only find legacy images on the website. Is there a place to get mainline images so I can test docker? Thanks in advance. Regards, Michal

Hi, I'm trying to put my OPI zero in mono instead of stereo by default. On ARMbian my alsa config file (/etc/asound.conf) looks like this : pcm.!default { type plug slave.pcm "dmixer" } pcm.!dmixer { type dmix ipc_key 1024 ipc_perm 0666 slave { pcm "hw:0,0" period_time 0 period_size 1024 buffer_size 4096 rate 44100 format S32_LE channels 2 } bindings { 0 0 1 1 } } ctl.!dmixer { type hw card 0 } I tried to add something like this but without success : pcm.makemono { type route slave.pcm dmixer …

Hello everyone, My bananapi is running on the mainline kernel. When i try to poweroff the bananapi it reboot's but without it's networking services online. The bananapi is connected to a battery, but i do expect it to power off completely. I came across this topic but it is about a cubieboard running on the legacy kernel. Is there somebody who can help with this problem? Thanks in advance.

Hi! Trying to setup HDMI audio on Banana Pi with Armbian Xenial mainline: root@bananapi:~# uname -a Linux bananapi 4.9.7-sunxi #1 SMP Thu Feb 2 01:52:06 CET 2017 armv7l armv7l armv7l GNU/Linux I tried adding Alsa config in /etc/asound.conf root@bananapi:~$ cat /etc/asound.conf pcm.!default { type hw card 1 device 0 } ctl.!default { type hw card 1 } root@bananapi:~$ speaker-test -twav -c2 speaker-test 1.1.0 Playback device is default Stream parameters are 48000Hz, S16_LE, 2 channels WAV file(s) Playback open error: -2,No such file or directory Any suggestions?

Just stumbled upon this new board by the Friendlyarm folks. http://www.friendlyarm.com/index.php?route=product/product&product_id=197 Lots of signals exposed on the strip contacts, including Ethernet and USB, though magnetics and connectors aren't there, which makes this even more interesting to build thin appliances: you add connectors when you need them. Good! I'll probably order a couple to start playing with, but will take forever to ship over here.

Looking for recommended LCD screens for NanoPi Neo and Orange Pi Zero. I have some IoT ideas I want to explore. Does not have to be touch, and I'm pretty flexible on screen size. Actually, would like a couple of different screen sizes but bigger than an 128x64 OLED (I have that). Must be color. At least 320x240, preferably something 320x480. I just got two Orange Pi Zero systems today and want to create a couple of IoT devices along with the two NanoPi Neo systems I got recently. Performance does NOT have to be ideal, just reasonable (not going to game on it or watch action movies). The Zero means HDMI is not an option; given that, what interface is best - …

Hello! Does anyone know how make hardware reset of the Pi one board?

Hi everyone! That's getting me off... I though it was plug&play but didn't, Anyone can help me giving me the solution to this problem? Thank you very much Kind Regards

http://www.orangepi.org/OrangePiR1/ Not sure how different it is from Zero other than the second ethernet port and new RTL8189FTV wifi. I'm waiting for a low cost dual ethernet box for a long time. Ordering now.

Hello! I asked this question here: https://github.com/zador-blood-stained/fel-mass-storage/issues/1, but I decided to ask again. Is there a way to boot the current mainline u-boot via FEL? Is it easy to support this issue? I would be happy to receive any help. Thanks, Aleksandr

I want to use an OPI zero (armbian 5.31) to log data from a smart meter to influxdb. Everything works, but after 5 hrs i cant ssh into the pi - also, no data is written to the db. The pi has heatsinks and the temperature is around 53°C. Now i tried it without the logging and after 5 hrs, the pi was again not reachable (i dont know, if it crashed or only the connection went down). Last try was with a pi lite which showed the same behavior. What could be the problem?

Hello all! Does anybody know how to make 5inch hdmi screen for RPI work with OrangePi One? When I try to connect it to my OPI one with armbian it is just white screen and no one of LEDs is lighting on the OrangePI PCB.

Sorta basic question, I have orange Pi Lite's, and Orange Pi PC+'s in various projects. The hardware looks similar except for emmc and ethernet, are the images interchangeable after installation?

Hi there, I am a new user of OPi PC+, downloaded, flashed Armbian_5.20_Orangepipcplus_Debian_jessie_3.4.112_desktop.img basic setup OK, got IP, changed passwords etc, GUI starts. As I don't have USB keyboard/mouse, I've opened SSH session, then set export DISPLAY=laptop2:0 , then xterm. OK. From BT side it also looks ok: adapter blinks, I can find my BT keyboard/mouse using hcitool scan Now the problem: if I launch bluetooth-applet / bluetooth-assistant it CRASHES (assistant) at step of PAIRING device. (applet still alive). So my quiestion is, how to pair this remote device without "assistant", and make it available as "normal" keyboard/mouse? [device …

Hi, I am using orangepizero with Armbian_5.30_Orangepizero_Ubuntu_xenial_default_3.4.113 ubuntu server image. I have also installed mate desktop environment to enable my desktop on my waveshare 3.2 LCD. Now the issue is my desktop freezes in my LCD couple of minutes after boot. I have used heatsink with fan, armbianmonitor show operating temp 40-50 deg cel and cpu load when i run any application 30-40%. I observed one thing when my desktop freezes in my LCD, i can access my orangepi with VNC as separate session where i can see my desktop and perform any task flawlessly without any freeze. Any help here?

Hi, When I put a heavy load on my NanoPi NEO2, it locks up. The ethernet light keeps flashing, so there is still something alive? After a power reset, the NEO2 works again. I've already put a CPU fan on my CPU. CPU temp is at 25 degrees Celsius in rest, and goes up to 37 degrees Celsius under the heavy load. The heavy load is a "make -j4" of a C source code project Tips how to solve this? sander@nanopineo2:~$ while true; do date ; uptime ; cat /etc/armbianmonitor/datasources/soctemp; sleep 2; done | tee mijn-log.txt Tue Aug 22 11:46:37 UTC 2017 11:46:37 up 5:24, 2 users, load average: 0.00, 0.00, 0.00 28342 …

as of some network release before the current (unsupported) 4.11.3 kernel, the networking has started having random value hw mac addresses on every boot. I suspect if you can do so and look @ your DHCP server, you will possibly see the orangepi (or whatever your hostname is) lurking there. Another way to do it if you have to, is to /sbin/ifconfig and get the HWaddr and look for that mac address on your dhcp server. I came by your post while trying to find a workable solution to assigning the mac on the orangepi zero 512 I am bringing up. Jim

I should probably start a new thread for this but it seemed appropriate to post here at this time of nght.. So the OPi Zero Plus 2 boards arrived and I duly set up the image on a 8GB SD card, connected the serial TTL to USB adapter and booted. Everything came up fine so I set up the wifi to my local network using nmtui. Again no problems. I did an apt-get update and upgrade and rebooted, all OK again. Having SSHed into the device I get very sluggish performance and pinging from another machine on the lan I see hugely variable pings ie variations from a few ms to over a second. I installed wavemon and it shows a very strong wifi signal (as expected). The ping…

is this possible? chromium-browser --use-gl=egl [1800:1800:1212/194050:ERROR:gl_surface_egl.cc(479)] EGL display query failed with error EGL_SUCCESS[1800:1800:1212/194050:ERROR:gl_surface_egl.cc(486)] eglInitialize Default failed with error EGL_BAD_DISPLAY[1800:1800:1212/194050:ERROR:gl_surface_egl.cc(479)] EGL display query failed with error EGL_SUCCESS[1800:1800:1212/194050:ERROR:gl_surface_egl.cc(486)] eglInitialize Default failed with error EGL_BAD_DISPLAY[1800:1800:1212/194050:ERROR:gl_surface_x11.cc(68)] GLSurfaceEGL::InitializeOneOff failed.[1800:1800:1212/194050:ERROR:sandbox_linux.cc(345)] InitializeSandbox() called with multiple threads in process gpu-proce…

Hello, recently got a pinebook. I have a strong Linux-on-PC-user background (running ArchLinux on my desktop & older netbook, and debian oldstable on my home server laptop), but not really a developer background and no experience with single board computers at all! Ubuntu Mate is happily chugging along right now, but video playback (h264 packed in .mkv) is abysmal to non-existent. I have tried these releases; the stable 0.6.2 first: AFAICS, it uses a frambuffer driver (fbturbo) under Xorg. video playback was more than choppy, and the UX drops to zero because the video window can't be resized and sticks to the screen, …

Hello. In my project, I want to use a linphone with support for the h264 codec. In repositories there is a version of linphone but without the specified codec. I tried to build a linphone from the source code, but failed. The matter is that the assembly of the dependent package belle-sip hangs (the assembly lasted 2 days). Tell me, does anyone have any experience in successfully building a linphone from git? Now I'm trying to build a linphone on the Orange Pi zero plus 2 H3 board.

HI.. I have an opi zero and I want to copy the card and use it in a NanoPi Neo I plugged it in and it works but displays Orange Pi Zero on the login screen. What steps should I take to make it work best in the NanoPi Neo? Thanks. V.

Hello, I made my microphone setup with microphone mce103 according to this scheme pin 10 (MIC-BIAS) ..... 3 - 15V in scheme, pin 11 (MIC 1P) ....... NF, pin 12 (MIC 1N) ....... (-) in alsamixer I have: audiocodec, mic1_2 audio capture mode. then I tried: arecord -i -f S16 -r 22050 test.wav and it saved this wav file (in attachment). I am not able to record audio, it records just noise as in attached sample. What can be wrong please? test_.wav

Hi to all, I'm newer so I hope your comprehension. my board Orange Pi Zero 512 my python script for turno on/off rele board works well, but only if call it directly form terminal. If call it from cgi, crontab don't controll the rele board: gpio.init() semms crashed but the script complete its work. What I'm wrong? Thanks ---- from pyA20.gpio import gpio from pyA20.gpio import port gpioinit = gpio.init() gpioscfg = gpio.setcfg(port.PA19, gpio.OUTPUT) gpio.output(port.PA19, gpio.LOW) print "ok" -----

How to start a sound&microphone on the Orange Pi Zero 2+ H3? root@orangepizeroplus2:/# aplay -l aplay: device_list:268: no soundcards found... root@orangepizeroplus2:~# uname -a Linux orangepizeroplus2 4.11.5-sun8i #3 SMP Thu Aug 3 08:36:37 CEST 2017 armv7l armv7l armv7l GNU/Linux root@orangepizeroplus2:~# lsmod Module Size Used by can_raw 16384 1 bluetooth 270336 0 qmi_wwan 24576 0 qcserial 16384 2 usb_wwan 16384 1 qcserial sun8i_codec_analog 24576 0 snd_soc_core 122880 1 sun8i_codec_analog snd_pcm_dmaengine 16384 1 snd_soc_core usbserial …

I have an orange pi+ 2e that is being used for pihole. I want to set my pi to use 1 cpu core, disable usb ports and set Ethernet link speed at 100Mb/s etc to reduce consumption however not all the changes will apply at once (see picture attached) If cpu is running at one core and ram at reduced speed, ethernet link speed will still be at 1gbps and the other way round when Link speed is at 100Mbps.

I know this is a well known topic but since I didn't find an issue like the one I'm having I felt the need of explaining it. I recently bought an Orange Pi Zero board + extension board with AV, micro and 2 additional USB + case. During the 3 days I've been testing it I've been having a lot of issues related maybe to the heat (or maybe not). I have built a streaming media server called Mopidy, which is pretty cool but at certain times it completely hangs when I'm reproducing audio (by the way, I'm using only stable Debian / Ubuntu because kernel 4.11 isn't detecting the soundcard for some reason). It sometimes takes 1 hour to get stuck, …

Hi, i am using orangepi PC (H3). i had tried follow link, test.mp4 file created successfully. (video fine). https://github.com/avafinger/ffmpeg_cedrus264_H3 now, i want to real time(20~30 fps) capture for /dev/video0 (gc2035). i tried mpv with gc2035, but it didn't worked. i want real time video capture using cedrus264. orangepi@OrangePI:~/tmp$ mpv tv:// Playing: tv:// [tv] Selected driver: v4l2 [tv] name: Video 4 Linux 2 input [tv] v4l2: your device driver does not support VIDIOC_G_STD ioctl, VIDIOC_G_PARM was used instead. [tv] Selected device: sunxi-vfe [tv] Capabilities: video capture read/write streaming […

Hi, I have noticed very strange behaviour of my OrangePi PC Plus. Device is connected to internet via Wifi. After successful connection, device is connected to VPN service. A cron script is checking every minute if VPN is working, and if not, it is restarting connection. On every hour, Network Manager is being restarted (you will see why is that so later). On every minute NTP is querryed for time synchronisation. After VPN restart or rebooting of device, device sends an e-mail notification via GMail. On eth0 there is DHCP server running (dnsmasq), which is providing internet to a device connected to OrangePi. So basically, you plug in ethernet cabl…

Hi Geeks! I am not finding my way out to get console output from Armbian legacy kernel using a USB to Serial adapter, Armbian by default doesn't let me to get the console output on my COM3 port, the cursor remains stuck at blank screen. What extra configuration do I need to do to my Armbian 5.31 orangepi zero with (Linux orangepizero 3.4.113-sun8i #18 SMP PREEMPT Thu Jun 15 02:16:06 CEST 2017 rmv7l armv7l armv7l GNU/Linux) ? I have attached my script.fex(UART config) below.. PLEASE HELP! Thanks.

I just booted up a fresh install of Armbian 5.24 (Armbian_5.24.161128_Orangepizero_Ubuntu_xenial_3.4.113) on my Orange Pi Zero and I can't seem to get IPv6 working. It worked fine on Armbian 5.22. It's like the dhclient command isn't able to set the address or the address is silently getting dropped or something. Setting ipv6 address via dhclient fails for both eth0 and wlan0. I ran dhclient by hand to see if a problem would be listed in the output but there's nothing: root@orangepizero:/var/lib/NetworkManager# /sbin/dhclient -d -v -6 -N -sf /usr/lib/NetworkManager/nm-dhcp-helper -pf /var/run/dhclient6-wlan0.pid -lf /var/lib/NetworkManager/dhclient6-1cfb9f48-cd01-41…

im using banana pi m1 trying to play around with gpio therefore tried almost every library for it, but found nothing working is there anything else i should do other than installing libraries?? like wiring 2 python LMK.GPiO etc. where should i start from as a beginner??

I installed the SoftetherVPN using the script provided in Armbian distribution, than I configured it from my windows machine, using the VPN Server manager application downloaded from softether website. When I try to connect from my iPhone I get an error "The L2TP-VPN server did not respond. Try reconnecting. If the problem persists ..." What I didn't do , is opening ports in my router, do I need to forward 443, 992, 1194, 5555 to my BananaPi IP in my router ? Some more details I posted on the softether forum, but it seems there is noone around to answer, and alot of spam is posted daily Thank you. VPN Tools>check Check command …

Hi, I am trying to use an Orange Pi Zero as a headless music player running MPD connected to a USB DAC. I have everything set up and it works well, but now I would like to add a momentary push button connected to a gpio pin to enable me to soft shutdown the Orange Pi Zero. I've done the same with python scripts that I've found in the Rune Audio forum (which runs on Arch Linux) for the Raspberry Pi, but I understand that the Pi Zero pins are different from the Raspberry Pi. This is the script I used on the Raspberry Pi #!/usr/bin/env python2 import RPi.GPIO as GPIO import time import subprocess GPIO.setmode(GPIO.BOARD) #Select unused GPIO header pin…

Hi my opi PC suddenly display disappears as no signal. Later multiple times rebooted but no luck . it seems to PC is booting even keyboard mice gets power but no HDMI display. Green led blinks on booting. Please help to find put problem Rizwan

Dear all... I run om my BPI M2 a minecraft server, fo my kids. Works great only my 8gb sd cart is not big enough for all the plugins my kids wil have.. They love the game, and are very proud to all there friends... And i am there smart DAD that can make all this stuff.......:-) I love to see my kids smiling, and playing on my board... Is there a option to enlarge the sd with a extra USB so i can place on the USB some plugins? Or is there a other way to enlarge the memory on the board? I see in the config a option to move something to a other device only i do not now how this working. If this option is a so…

Hi. I configured OrangePi zero with the NAS interface and with Openmediavault. I also configured ethernet card and wifi. Everything works. But if I disconnect the network cable, I also disconnect the wifi. Now I would like the wifi to work even without ethernet cable. This is possible? Many thanks ps. this the version of software ARMBIAN 5.31 stable Debian GNU/Linux 8 (jessie) 3.4.113-sun8i

Dear All, I build a minecraft server for my 2 lovely kids,,[ and a little bit for myself ] on my Bpi M2 http://www.banana-pi.org/m2.html I run armbian on the board, and i am very happy with this OS> 64gb sd class 10 U3 in it... I read in the documentation that i can give the CPU a boost, with Performance tweaks.. https://docs.armbian.com/ Only i can not let the server crash, so i hope there is some on that can help me with the tweak. I do not now how i can make this tweak and i need a stable server, so i think i cannot go to the highest settings. Only what i say... no experience with this tweak. …

Hi guys, I have been following this two sources below while trying to build my own pps ntp server with orangepi plus. I have got gpsd and pps work. However, I have ran into the problem that the chrony I got from apt-get doesn't have pps support. It will outputs "Fatal erre : refclock driver PPS is not compiled in". I have tried building chrony from source with timepps.h but that couldn't even run properly without pps source. I am stuck with the problem. I would appreciate any advice. Thanks! 1. 2. https://www.blackmagicboxes.com/?p=581

NanoPi NEO2 Debian jessie 4.11.1-sun50iw2 mount.cifs doesn't load if iocharset=utf8

I have OrangePi Zero and want to use it the following way: 1. OrangePi Zero is connected to internet via Wi-fi 2. on OrangePi's eth0 port is running DHCP server 3. I connect a computer to eth0 port on OrangePi, get IP address via DHCP and access to the internet So internet is provided to eth0 via wlan0. Now, I managed to install dnsmasq, and it is working. Basically my config (/etc/dnsmasq.conf) is: interface=eth0 listen-address=172.16.0.1 bind-interfaces addn-hosts=/etc/dnsmasq/hosts.conf dhcp-range=172.16.0.50,172.16.0.150,12h dhcp-leasefile=/var/lib/misc/dnsmasq.leases IP of eth0 on OrangePi Zero is: ifconfig eth0 …

Hello everyone, I have purchased an OPI PC + with intent to use it as a reciever for OGN, a network of recievers used for monitoring FLARM position info of equiped aircraft. http://wiki.glidernet.org/ I have flashed the Legacy 3.4.112 Jessie Desktop image first to the sd card and then installed it to the internal memory of the device. All went smoothly thus far. Then I ran into the problem that is the reason I am posting this thread. When I ran the bootscript for the installation of the OGN software, I got the following error message in the console: Bootscript source: http://ognconfig.onglide.com/ root@orangepipcplus:/home/andrej# wget http://ognconfig.…

Hi, I'm trying to run a DHT22 Temperature & Humidity sensor on my Cubieboard2 but I seem to fail at the beginning on how to use the GPIO Pins correctly What I have: Cubieboard2 Armbian Linux version 4.11.6-sunxi (root@devel) (gcc version 7.1.1 20170510 (Linaro GCC 7.1-2017.05) DHT22 (worked on a Raspberry Pi3 before) What I've done so far: According to this Overview (http://docs.cubieboard.org/cubieboard1_and_cubieboard2_gpio_pin) I connected the sensor on 3v3, GND and on PD25 (LCDDE). As far as I understood the LCD pins can be also used for other things. Followed "Accessing the GPIO pins through sysfs with mainline kern…

Hi, I was wondering if anyone had been able to get this working ? And, yes i know that OPI-Win is WIP/testing. I read some stuff here & on the linux-sunxi irc log that seemed to say that it should work & I've tried the following without luck. I was wondering if someone with alittle more knowledge about this may be able to help or point me in the right direction. I also tried to compile u-boot v2017-09 but it fails with a sdram too big error I tried to backport some of the config to 2017-07 but that'll take time i expect ... /boot/armbianEnv.txt (many combinations of this) disp_mode=720p60 disp_dvi_compat…

Hello everyone, I'm having some isues with my olimex board. It boots fine on the images supplied by olimex. But the Armbian legacy images wont boot. I have a serial connection to the board it hangs on the following line: <6>axp20_ldo2: 1800 <--> 3300 mV at 3000 mV. http://pastebin.com/nEHAiZHa I need legacy for i2s support so mainline isnt an option. I use the following board(tried 3 of these): https://www.olimex.com/Products/OLinuXino/A20/A20-OLinuXino-LIME-4GB/open-source-hardware I used the following armbian image (jessie and wheezy give the same error): http://www.armbian.com/olimex-lime/ Building the image myself also doesnt work.…

After setting up my static IP address, I can't SSH or Ping to the board anymore. The board shows up on my router list of connected devices, and the Pi Hole works normally. I flashed a new SD card and went step by step to see what was causing the problem. I resize the filesystem, update and upgrade the system, then I set up the static IP, so this happens. I tried both by /etc/netwkork/interfaces and by nmtui. This is what my /etc/network/interfaces file looks like: auto lo iface lo inet loopback iface eth0 inet static address 192.168.25.160 netmask 255.255.255.0 gateway 192.168.25.1

I have OrangePi Zero (basic version without HDMI) and OrangePi PC+. However, devices came with almost no documentation, so I would like to know the pinout for GPIO pins. Is there any documentation available? BTW, I need to solder GPIO pins to OP Zero, but it is OK.

Hi Does anyone know if the OPi Lite's WiFi is meant to automatically reconnect if the AP reboots or disappears and then comes back? What is the default behaviour supposed to be? Is it meant to automatically scan nearby networks? Thanks

So, hello. Sorry for bad/broken English, I'm still teaching it. As in title, I can't boot my orange pi 2 plus from sd card. I have tried with one tv(hdmi-hdmi 1920x1080), and one normal pc monitor (hdmi-dvi 1440x900) sd card is 8gb class 10 producent "team". I burned my image with Etcher 1.1.1 Funny is that, lubuntu image from eMMC is working fine, I've tried to boot lubuntu, ubuntu, image, with no effect, the only image that works is from eMMC(i have installed it months ago) At start, the green LED lights up and after 5, maybe 10 seconds red LED is blinking, something like blink-blink-2/3 seconds break-blink-blink I feel like I should create this …

Hi, I trying to use UART 1 & UART 2 at OPi Zero 2 Plus with no success with armbian stable and ubuntu server. I test all combinations, of fex settings, turn off everything except required uarts, set uart_type = 2 and etc, and it did not connect. UART0 and UART3 works fine, but I need cts-rts lines from uart2 for hi speed (it's uart_type = 4, but I would like to start regular uart first). tested with picocom, ft232 & pl2303 I use 8 & 10 pins for uart 1 and 11&13 for uart2 as described at http://linux-sunxi.org/Orange_Pi_Zero Is it correct pins? Thanks

Hello, I'm starting in this world with an Orange Pi Lite, but I'm not being able to perform the initial setup using serial console gadget on the OTG port. To prevent power problems, I'm using the DC input. Unfortunately I haven't found enough information to make the configuration on a Linux PC, since I wasn't able to know the /dev address to connect through screen. You've probably noticed that my knowledge of Linux is rather scarce. Thanks in advance!

Hello, guys, please help setup HDMI output to 480x320 in mainline kernel for BananaPi M2. I am using 3.5inch HDMI display, it is working fine but my current resolution is too high. All attempts to change disp_mode in armbianEnv.txt didn't help. Thanks

I have Orange PI Zero running the stable Ubuntu image. Kernel: Linux orangepizero 3.4.113-sun8i. I'm writing a python3 app to communicate with an Arduino using UART. The app works fine for a few hours and then it stops being able to send or receive commands to/from the Arduino. Is there some known issue with the UART on OPI Zero? It looks like the file descriptor for the serial port becomes unavailable somehow.

- A64 - strange naming "win"

So I apologise in advance because I'm sure it's probably on this forum but I could not work out the buzzwords to find it. For whatever reason, I upgraded the cubietruck with armbian which has been on since forever and rebooted for the first time this year. On reboot it failed to find /boot and a few other things and kept bootlooping, resetting itself and then following the same procedure. I already had installed the system to my SATA SSD, so this isn't a huge deal. I've flashed the latest armbian release onto the SD card and it boots fine. Now, I see there is an install to sata option in armbian-config but it gives me the warning that it will wipe …

Hello! The Cubieboard2 with mainline kernel support LCD through DVK522 board (LVDS connection)? The mainkernel support SPI?

Hello, I install Armbian on my Orange Pi Win Plus, i use the image for Orange PI Win i have the boot starter after nothing, someone can help thank you

Hi, I own the first Orange Pi (A20, VGA, HDMI, NAND, 4xUSB, WiFi). I notice there is no Armbian image for download anymore. The last one I still have is a 3.4.113, 5.25 Ubuntu/Xenial-default-desktop (currently running from the NAND very well, but I can't seem to run the wifi in AP mode). Is Armbian for this board is dropped for good ? Is there a way to update my 5.25 to last version without breaking everything ? Or maybe convert a A20 image to this board, using the working image I'm currently using ? Thanks !