Rockchip

I have a 5B and it came in a kit with the 10.1" touchscreen because I wanted to try to do a kiosk. I used Armbian Lunar rolling to get the OS installed on the emmc but I haven't been able to get the touchscreen working. It uses a breakout board to split the LCD2 connector into two connections on the display (I'm assuming one is touch and one is display) and when it's all plugged together, nothing happens. I've tried enabling and disabling both orangepi5lcd dtds and it doesn't help. When I do a dmesg (regardless of the screen being attached) I have Goodix i2c error for touchscreen@14 I've been doing Rockchip SBCs …

Hello, I am trying to boot my 4C+ from SPI. I soldered the chip and after adding "overlays=spi-jedec-nor" and "param_spinor_spi_bus=1" in "/boot/armbianEnv.txt", "ls /dev/mtdblock0" returns a result. After running "nand-sata-install" the entry "Boot from SPI - system on SATA, USB or NVMe" is missing.

[🌱] artifact [ armbian-desktop :: armbian-desktop() ] [💖] artifact [ present in local cache: armbian-bullseye-desktop-gnome 23.05.0-trunk--1-V5999-B8177 ] [🌱] artifact [ armbian-bsp-desktop :: armbian-bsp-desktop() ] [🌱] Getting ORAS manifest [ ORAS manifest from ghcr.io/armbian/cache-packages/armbian-bsp-desktop-orangepi5-legacy:23.05.0-trunk--1-B0996 ] Error: GET "https://ghcr.io/v2/armbian/cache-packages/armbian-bsp-desktop-orangepi5-legacy/manifests/23.05.0-trunk--1-B0996": GET "https://ghcr.io/token?scope=repository%3Aarmbian%2Fcache-packages%2Farmbian-bsp-desktop-orangepi5-legacy%3Apull&service=ghcr.io": response status code 403: denied: requested access…

Orangepi 5B 1. The armbian with sd card can not detect orangepi 5b emmc disk 2. with orangei5b official image and boot , write the armbian image to emmc , can not boot into UI desktop and drop into inicramfs shell.

Hi, i just want to inform that onboard wifi (AP6275P) on Orange Pi 5b doesn't support at this moment. Is there any plan to support it in the future?

Hello guys, you know that armbian has a problem that sometimes when the system boots, the ethernet interfaces fail. The led turns on indicating that it detected the interface but it is totally blocked. It does not work, no method of restarting the interface. The only solution is to restart the computer...

Hello, just yesterday I got my new Orange Pi 5B. Unfortunately I'm facing the issue, that I cannot see any EMMC on Armbian. The Debian image that is delivered by Orange Pi itself is giving me access to the EMMC - so it's there with 256GB physically. lsblk shows only the SD card and zram drives. gparted is not starting up after installation at all. This is valid for all official downloadable versions like Jammy, Bullseye, Bookworm... Is there any driver available I would have to activate to use the EMMC device with the Armbian images? I'd really like better to run the board without SD card. Any idea?

Hi guys, I need to be able to see the pins on my board. In the official distribution of Orange Pi, I was able to install the Xunlong WiringOP script. I know I can use /sys/class/gpio/ to define the pins and use them, but that's not what I want. I would like to be able to use something like the "gpio readall" command.

Hi guys, when I installed Armbian on my system, it gave me a different MAC address than the one physically assigned to my hardware. How can I restore the original MAC address of the hardware without having to manually set it?

Download: https://www.armbian.com/nanopi-r6s/ (unofficial WIP support)

I see that there is a lot of work ongoing on improving the UEFI boot support for Rock 5B and this is quite exciting. In my view this seem to be the ideal route for future SBC boards. However, I am yet to try it so I am still a novice in the area. How do you guys look at the future of UEFI vs U-boot for Linux on SBC’c in general and on the Rock 5B in particular? Will the UEFI version be as capable as a u-boot version or do you see limitations?

I am using a Linux rockpi-4cplus with 5.15.93-rockchip64 (bullseye). I plan to use SPI1 (GPIO1_A7, GPIO1_B0, GPIO1_B1, GPIO1_B2), and then add in a 2nd device on this SPI bus via a custom CS GPIO pin (GPIO4_D5). I could not find the corresponding script file (.DTS) online (on Github) associated with the object file (rockchip-spi-spidev.dtbo). Please could someone point me to it - I can only find files for "sunxi-DT-overlays". So I decided to create my own DTS file, as follows: /dts-v1/; /plugin/; / { fragment@0 { target = <&spi1>; __overlay__ { #address-cells = <1>; …

Hello, i like to activate / use more RS232 UARTS. What is the best way to do this ? Thanks a lot, René

Hey, Has anyone managed to capture image from this camera? `media-ctl -p` shows this device, that mentions the camera name: - entity 63: m00_b_imx415 3-001a (1 pad, 1 link) type V4L2 subdev subtype Sensor flags 0 device node name /dev/v4l-subdev2 pad0: Source [fmt:SGBRG10_1X10/3864x2192@10000/300000 field:none crop.bounds:(12,16)/3840x2160] -> "rockchip-csi2-dphy0":0 [ENABLED] But that's it. No luck with libcamera nor v4l2-ctl. The `rock-5ab-camera-imx415` layer enabled.

I'm owner of a rock 5b with an nvme drive installed. I'm already running Armbian_23.02.2_Rock-5b_bullseye_legacy_5.10.110 from the nvme. I want try the edge images but I cannot boot them from the SD. I have tried with Armbian_23.05.0-trunk-e33842ef2_Rock-5b_lunar_edge_6.2.9 and Armbian_23.05.0-trunk-e33842ef2_Rock-5b_lunar_legacy_5.10.110 Am I missing something?

Hi, An old problem, since I got the board which is 4C. Not a + - or whatever but the plain C. Symptoms: 1. HDMI worked randomly, maybe every 10th...15th boot lead to a working system, or rather to a visible HDMI-connection. But now switching on-off does not help at all. 2. Quite often one can get the board booting to the point where it asks for the password, and after clicking ok, it switches the screen off, and won't return. So the telly says that "no signal". 3. When switching on the board the tv set sees that there's someone on the hdmi port, and shows the booting sequence, and finally goes to Armbian's graphical mode asking for t…

My Sata SSD drive works very slowly on Orange PI 4, using usb 3.0 port. On PC based on Windows 11 via usb 3.0 it works correctly. I found problem on Armbian 23.02(trunk, 30.12.2022, edited parameters: installed software, bluetooth parameters) when I try move system onto SSD, first time it works normaly, but not so fast, as expected and automatically starts in read only mode. Read only mode I have fixed. Sometimes it breakes ext4 partition, that I've fixed using fsck, and fix again when ext4 breakes again and not working/works badly. After some time it begun freezing. I tried to find solution by myself, but not found good advices. I've tried some mounting parameters, …

Hi, I don't know if this has anything to do with it, but I had a functional Armbian distro on the Rock5B working from the SDCard, and after installing it on the NVMe (which does not boot), I restarted the board from the SDCard (after having removed the NVMe), and I lost my network connections. How could I get the network back on? And the UART regularly asks me: Give root password for maintenance (or press Control-D to continue): Give root password for maintenance (or press Control-D to continue): Something must be broken... root@rock-5b:~# uname -a Linux rock-5b 5.10.110-rockchip-rk3588 #23.02.2 SMP Fri Feb 17 23:59:20 UTC 2023 aar…

Hi there, My Rock5B worked well with Armbian until I tried to migrate to an NVMe. Here is a boot log without any SDCard: Spoiler DDR Version V1.08 20220617 LPDDR4X, 2112MHz channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB Manufacturer ID:0x6 CH0 RX Vref:31.7%, TX Vref:21.8%,21.8% CH1 RX Vref:30.7%, TX Vref:21.8%,20.8% CH2 RX Vref:31.7%, TX Vref:21.8%,21.8% CH3 RX Vref:30.7%, TX Vref:22.8%,21.…

I downloaded "Armbian Lunar XFCE desktop" image from https://www.armbian.com/tinkerboard-2/ and mounted it to the SD card. Then I booted the board but it couldn't boot. Only the red LED is on. The tinker os can boot and work well. The red LED is on and the green LED keeps blinking. How could I do to boot Armbian on this board?

Howdy Is anyone having issues with speed negotiation? My rock 5b running an unsupported kernel is selecting 10mb instead of the 2.5gbe the zyxel switch is capable of. Thanks

Hello, I have this combinations which was probably a mistake, because I cannot get the camera running whatever I do. Was someone able to get it up or give me some advice, lead me a good direction? Thanks a lot.

Hello people I would like to share my experience with the Mekotronics R58 mini PC (RK3588 box, in my case with 8Gb RAM and 32Gb EMMC). For a more review like post see NicoD's video review here on the Armbian forum: he just reviewed the new MonkaArmbian on this board. I got the Download links from NicoD, and in the meantime they are also on the official Mekotronics support site. I just want to share my experiences with others. So first I played a bit with Adroid 12, that came with the box. Android is the best supported OS for this box, performance wise. Video and emulated gaming seems to work great also 4K. But I wanted Linux on it, so I installed Debian from …

Dear all My nanopi M4 V2 does not start My configuration is a sd card for booting + a NVME for the system. I have installed a lot of applications : OMV Docker with portainer history : I would change version from nightlight to stable with a bug during the pre-configuration of OMV. I need to perform a CTRL + C to stop this frozen action. After that I reboot my device with the same issue from post 1 Could you please help me to recover my device ? I would like tried to comeback to the previous version But I do not find the process. Tha…

I finally have openZFS loading as a module with modprobe (still need to test that it's actually working correctly, but so far so good...) I'm using the Armbian Lunar CI rolling release since there is a working Linux-Header for this kernel https://imola.armbian.com/beta/pool/main/l/linux-headers-midstream-rockchip-rk3588/ After that, I essentially followed the instructions for building openZFS, but some minor changes to the META file for license and max kernel version. I want to say thank you to all the Armbian team members for making such an amazing platform for SBCs. All my boards run Armbian. here was the config command …

Hi, I've booted the board from SD card with the latest image and I'm trying to configure the board to boot from MTD and use USB drive as a system drive. When running armbian-config (or armbian-install, or nand-sata-install), it fails with error "SPI u-boot image not found!". It looks like the bootloader package is missing the /usr/lib/linux-u-boot-current-rock64_23.02.2_arm64/rkspi_loader.img. Can I find it anywhere? Dmitry

Hi, I've installed Armbian Jammy on a Rock 3A. It seemed to run very stable, (much more so than the Rock 64) however the first IMPORTENT issue I've found is that the system appears to freeze when Chromium is launched as well as VSCodium. That is to say I loose mouse and keyboard control, so I can't tell what else may be effected. There may be others, still checking. Any help appreciated.

Hello everybody, I'm new with the SBC and with Armbian and I hope you can help me. I'm working with a Tinkerboard 2 R2.0, where i would like to be able to cut the USB ports supply. I have noticed on the Tinkerbords R2.0 schematics the USB_OUT_EN_5 line. I'm wondering if this line is conneted to a CPU pin and, if it is possible to drive it? Does anybody know a way to cut the USB ports power supply? Thank you

I have a Rock4 SE Board (or Rock Pi 4 SE) and I'm using the Armbian_23.02.2_Rockpi-4b_bullseye_current_5.15.93 Debian version. (Linux rockpi-4b 5.15.93-rockchip64 #23.02.2 SMP PREEMPT Fri Feb 17 23:48:36 UTC 2023 aarch64 GNU/Linux) I am trying to set up the correct Device Tree Overlay configuration for my intended application. If I use Armbian-config as a tool to demonstrate the issue here. It starts by listing I2C7 and then I2C8. If I go to the Rock4 SE schematic and search for I2C8, it is not even setup as I2C: Then where is I2C6, for example. It's supposed to be there. If I then look fu…

I installed panfrost but glxinfo still lists the device as llvmpipe. I'm using Armbian_23.02.2_Rockpi-4cplus_jammy_current_5.15.93_gnome_desktop running wayland. This is how I built panfrost meson . build/ -Dvulkan-drivers= -Dgallium-drivers=panfrost -Dllvm=disabled ninja -C build/ ninja -C build/ install i have no idea what to do next because there is no errors that I can find and I was under the impression that with a kernel 5.1> it is supposed to work. Any help is appreciated

Hi, I have tried booting multiple different images from Armbian, But when I bootup I get the message below. I have tried 8 different charger, 5V 3A, PD 3.0, 35W charger, 10W charger... I'm using a Sandisk Extreme SD card, I have flashed the board using both the SPI found from radxa wiki, and the rkspi_loader.img found from github. If there is any other information, please let me know. Should be noted that I took a picture and used image-to-text to get the output below. 15.1599071 usb usb?: Manufacturer: Linux 5.10.110-media xhci-hcd 15.1616491 usb usb?: SerialNumber: xhci-hcd.9.auto 15.1636651 hub 7-0:1.0: U…

Having some issues here. I wrote the newest Ubuntu CLI to my SD card. I booted into the device and used Armbian-Install to move the root to the NVME. I fixed the UUID on the fstab file. I was able to boot up from the SD + NVME. I did an apt update + upgrade, that seemed to go well. I rebooted the device and it won't boot. I get this on the screen: 1.436035] Initranfs unpacking failed: broken padding 2.1982061 Kernel panic- not syncing: No working init found. Try passing init option to kernel. See Linux Documentation/admin-guide/init.rst for guidance. 2.2177021 CPU: 4 PID: 1 Comm: swapper/0 Not tainted 5.15.93-rockchip6…

I was wondering if the Armbian 11 Bullseye release would get a release candidate for the following ppa's for Panfrost: ppa:liujianfeng1994/panfork-mesa ppa:liujianfeng1994/rockchip-multimedia Because I was really hoping to use Debian over Ubuntu for my purposes of familiarizing myself with the distro, but only Jammy so far has a candidate for these. I also tried manually installing the Panfrost/Panfork drivers on Bullseye and only got it working once before borking my entire system, and I cannot replicate it. Any help or information would be greatly appreciated, as the GPU acceleration on Jammy is simply amazing!

I have been trying to power on the Tinkerboard, but I haven't had any luck. The red power light never turns on What have i tried so far: I have tried connecting it to my PC using USB-C using a 12V power supply Using the Raspberry Pi USB-C Power Supply have even exchanged the device, but the issue persists.

I noticed today that there are no 23.02 images for the rockpi-4c. The images exist for the 4a, 4b and 4cplus variants but not the 4c. The 22.11 images are the latest for the 4c. The reason I noticed is that on the downloads page for the rockpi4 it is still showing 22.11 as the current images because that page is showing the 4c info, with links provided to the other variants. The fact that it still showed 22.11 caught my eye.

Hello, did somebody already have success connecting a Raspberry Pi 7 inch display to the current Armbian build? I already tried to add this overlay via armbian-add-overlay, but this did not work. What am I missing? Thank you for your help!

Hey guys, First of all I would like to let you know that the default DTB has an issue, the GPU status is disabled by default. I've changed this & now my GPU is detected & working fine so far. (Armbian Jammy current) But I'm also facing some other Issues.... not all USB Ports are working, just 2-3 & the working ports sometime are randomly switching after a reboot. Bluetooth isn't working at all I guess these Issues are also related to the dtb file because I didn't find any entries for BT in the DTB. I also tried the other DTB file: rk3399-rock-4c-plus but I dont have any video output with it but there…

Hi! I was happy running Armbian on my Rock5, but for the second time in a week I got this panic: The journal from that boot seems empty: Any suggestions on how to debug/improve this? Thanks!

Having a problem with my board and screen. Recently purchased a couple of inexpensive touch screens that work dandy for pi and lepotato but the resolution on renegade is too high and text just looks like dust on a 7 inch monitor. I took a look at potato xorg driver.conf and there's a lot of modes listed, but on renegade I see: Section "Device" Identifier "NOGPU" Driver "fdev" Endsection And xrandr -- listmonitors output: Failed to get size of gamma for output default Monitors 1 0: +default 1600/423x900/238+0+0. I'm still learning things, but I know exactly how to brick it again 😃. I hope I…

[22787.457010] Internal error: Oops: 0000000086000004 [#1] PREEMPT SMP [22787.457594] Modules linked in: xt_nat xt_tcpudp veth xt_conntrack nft_chain_nat xt_MASQUERADE nf_nat nf_conntrack_netlinks [22787.465404] CPU: 1 PID: 609416 Comm: kworker/u8:5 Not tainted 6.1.11-rk35xx #23.02.2 [22787.466103] Hardware name: Radxa ROCK3 Model A (DT) [22787.466552] Workqueue: ext4-rsv-conversion ext4_end_io_rsv_work [22787.467107] pstate: 804000c9 (Nzcv daIF +PAN -UAO -TCO -DIT -S…

Armbian 22.11.2 Cinnamon desktop was successfully installed onto eMMc storage from a microSD card. However, after installing the 3D accelleration following the official Armbian instructions, the Rock 5b failed to load the desktop. Instead, after the display of the Armbian splash screen, the screen turns black with a flashing white cursor. This problem started on 25 February. Before that day, 22.11.2 Cinnamon desktop successfully operated with 3D accelleration for two months. The following was used to install the 3D accelleration: sudo add-apt-repository ppa:liujianfeng1994/panfork-mesa sudo add-apt-repository ppa:liujianfeng1994/rockchip-multimedia …

Hi, I just downloaded the newest release of Armbian and flashed into the SD card, it boots up fine from the SD Card. But I wanna install the system into the Samsung PM9A1 SSD, So I followed the instruction on the armbian page, partioned the drive and made a ext4 filesystem. but I got stuck when I tried to boot up from SSD. I hooked up a serial cable and got this information Any idea about this?

So I did the upgrade to OMV6 (and associated kernel update Linux 5.15.93-rockchip64). Now in the mornings or after long periods of no interaction, the Helios enters an unresponsive state where none of the docker containers respond and I can no longer ssh in. There is still some sporadic noise comming from hard drives doing things and lights on the front are showing it's not completely frozen. I suspect it's attempting to enter some kind of suspend / hibernate state that is not appropriate for this system. Which would be the appropriate log file to go hunting for answers for sleep/hibernate issues on Armbian? And what w…

I have tried the Debian image for ROCK5B and the Gnome GUI works fine there. But when booting the Armbian image (running from emmc) the screen does not notice any signal from the ROCK5B regardless of which HDMI port I try. I am using a quite old HDMI monitor (connected though a DVI-HDMI adapter). How do I debug this?

Hi, I've installed Armbian 23.02 Jammy Gnome (Release date: Feb 18, 2023). Mostly it works well, including the instructions on the download page to enable 3D acceleration. However, my video is output to a TV through HDMI, and there is no audio. There are four "Analog Output - Built In Audio" options in the sound settings, I have tried all four and none of them make any sound. I have also tried to change all five options in the configuration tab of PulseAudio volume control. All are labelled "Built-in Audio" and there are no options in any of them other than "Stereo Output", "Stereo Input", "Stereo Output + Stereo Input" and "Off". I don't know if this is related, but…

Hey there, for quite a while I was using my Station P1 aka T-Firefly ROC-RK3399-PC-PLUS (with a nice case welded around) as crude NAS and wanted to do something new. However for unknown reason I cannot boot from microSD. I am used to that the Armbian boot loader should switch to microSD when detected so other OS can be used. Does not work though. It always starts booting from SPI which is fine in theory and then jumps to eMMC which boots fine. With SD inside it does the same. If I remove the eMMC module u-boot stucks to PXE which obviously fails and then drops to U-Boot shell. I played with that shell for a while including recovery…

The initial installation went fine from the flashed image on SD card, and still works fine. However, after using armbian-config to attempt to transfer the OS and bootloader to the eMMC card, nothing actually changes. It says it formats the card and then goes through the process of transferring the files, or at least it looks like it does. But when I reboot it it's still running on the SD card and no files appear to have been transferred to the eMMC. fstab lists the UUID of the SD card and not the eMMC at all; this is also true of the bootenv section of armbian-config. One thing I did notice is that there are some new directories under /mnt : '/mnt/nand-sata-in…

Could anyone help me to enable display with Armbian? I just can’t figure out why it doesn’t work. I don’t see the backlight turning on either. What do I have to change? I have tru to add a custom dts on kernel but don't work

Looks like my Rock Pi 4C+ does not recognize builtin sound card: root@rockpi-4cplus:~# aplay -l **** List of PLAYBACK Hardware Devices **** root@rockpi-4cplus:~# armbianmonitor link: https://paste.armbian.com/xucibilaza It seems to me that there are some clues here: What is the issue? How can I fix it?

Hi, I had to change the Rack 1 HDD because I got an email telling me that this disk was broken. So I ordered new discs to make my replacement. When I put my new disk my problem started. For information my old disk was perfectly visible before I changed it and the led was functional too. I have a strange problem and I'm afraid it's hardware. Currently I have Rack 1 (HDD 1) which no longer detects my disks, there are no more LEDs lighting up, we can clearly hear the HDD lighting up, but it is not visible in the CLI and not via the WebUI. Im using OMV 6.x with kernel 5.15.89 (current) stable RAID 6 with 5 x 8To Have try…

Hello, I have been looking for the solution to give access to the GPIO from the PI user for several weeks, does anyone have the solution? For information, I use a RockPI 4B+ under Armbian 22.11.4. Thank you in advance for your help. Regards Laurent

Hello, I don't know if I'm posting in the right section, if I'm wrong, please excuse me and move the topic to the correct section or tell me which section to write in. I will soon be the proud owner of a NanoPi R6S and would be happy if I could help create a working image for it. I don't have positive experience with compiling a kernel for SoC, but I can test images Regards,

Hello There! I'm currently using a Rock 4SE, tagged it as 4B because armbian says I should use the version for the board. I'm using a manually built image of armbian, though without any changes. I'm currently trying to figure out how to get faster boot times on SDDMC. So far: 1 - I've disabled some systemd services. Bluetooth related services have made a big difference. 2 - I've tried to disable USB and network support on U-Boot, though unsuccessful, in order to make U-Boot spend less time before booting the kernel. By applying some patches to U-Boot I got to the point where it either compiles and doesn't start the system because of some …

Hey, Was able to bring up a pretty smooth armbian installation for a lightweight desktop. Tips for others: Underclock Memory for stability cat /etc/rc.local #!/bin/sh echo 1560000000 > /sys/devices/platform/dmc/devfreq/dmc/max_freq For bluetooth blacklist the following modules: blacklist pgdrv blacklist btusb blacklist btrtl blacklist btbcm blacklist btintel NVME boot, use armbian-installer, but I had to manually change the firmware to this one: https://wiki.radxa.com/Rock5/install/spi#Simple_method to get NVME boot to work For GPU acceleration install panfrost. (See rock5b ambian page) To get my wid…

I have recently bought a rockpi5 and i was looking all over the internet for a POE hat module to power it up . However i was unsuccessful so far. I have tried the poe hat i had for my rockpi 4 B but it doesn't physically fit so my question is will a POE hat for the rockpi 5 be anytime soon released ?

Hello to everyone Trying to use armbian on RockPi 4C plus. Got kernel OOPS. Kernel crushes in different moments: mostly during systemd units starting or just after boot finished. Backtraces are different (no common). Faulty images: 1) From the https://www.armbian.com/rockpi4/ For Model C+ here: https://redirect.armbian.com/rockpi-4cplus https://mirrors.dotsrc.org/armbian-dl/rockpi-4cplus/archive/ Armbian_22.11.1_Rockpi-4cplus_bullseye_current_5.15.80_minimal.img 2) Built by myself Armbian_22.11.2_Rockpi-4cplus_bullseye_current_5.15.84_minimal.img Armbian_23.02.0-trunk_Rockpi-4cplus_bullseye_edge_6.1.8_minimal.img Armbi…

Hey there, I just joined the ARM universe & to be honest I lost all my skills with Linux. First I tried some official images Armbian_22.11.1_Rockpi-4cplus_jammy_current_5.15.80_xfce_desktop.img & with all of them I got a Blackscreen after the Logo. (all settings were made) Then I a tried a pre-release so I could finally get into armbian. Wifi : I couldn't connect via. wifi, "wifi network could not be found" But it was listed with a good signal strength. BT: no adapter was found. ( I used armconfig to enable BT) USB: just 3 of 4 usb ports were working. ( I guess it was 1x usb 3.0 & 2x usb 2.0) The Rock P…

Hi, I've installed minimal cli version and it restarts when connected to PC via on-board USB-C connector. Board hangs after: [ OK ] Reached target Hardware activated USB gadget. Host computer does: [ 4881.959467] usb 1-5: new high-speed USB device number 47 using xhci_hcd [ 4882.140301] usb 1-5: New USB device found, idVendor=0525, idProduct=a4a6, bcdDevice= 5.15 [ 4882.140315] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 4882.140322] usb 1-5: Product: Gadget Serial v2.4 [ 4882.140327] usb 1-5: Manufacturer: Linux 5.15.80-rockchip64 with ff580000.usb [ 4883.572730] usb 1-5: USB disconnect, device number 47 [ 4884.079492] usb 1-5: …

Hello, I am new to Armbian and Linux and want to set up my raspberry pi camera module 2 for my rock pi4b so I can start doing computer vision work. Does anyone know how to do this?

Hello, Apologies for wrong tag, but I am hoping one or more can help with what has been a frustrating process for a Linux\Orange Pi newbie. Background information: I got Orange Pi 800 due to shortages with Pi 400. I wanted to run home assistant on it. Came to determine to get what I wanted would entail having Debian installed and not Ubuntu. Flashed the micro sd card and the Pi 800 does not boot to it. I was able to remote to it via Putty, but I was not able to set it up correctly. What ended up happening was Debian got installed but not in the way I expected. The Orange Pi desktop still boots but I get system application error. The Orange Pi can see the micro…

Hi, I've downloaded the latest two images from the links mentioned https://disk.yandex.ru/d/-zSW21XKN0pfIA/ArmbianTV/20230103-edge But none of them boot from SD on my M3 box. The only one booting is the image from this link https://redirect.armbian.com/station-m3/Bullseye_legacy_xfce But this makes the cooling fan on the M3 to always spin at full speed and it's not usable because of this (it's really noisy). How can I make the other images boot? Tried both Etcher and USBimager. Please help. Thanks.

Greetings to the happy owners of the rock 5b. Tell me if the rock 5b turns off the power to all its components when shutting down. I understand that the power from the external power supply is still being supplied. And what happens to the devices on the board: ssd, fan, wifi etc.

Main Makefile references python2 as python. PYTHON = python PYTHON3 = python3 ideally change this to PYTHON = python2 PYTHON3 = python3 I quickly just made symlink and force a re-install via and removed the symlink afterwards apt-get --reinstall install <package name> Not an issue with later version of kernel header package (looks like only uses later python3 scripts.) ----------------- Sorry haven't had time to check if issue upstream or best way to patch it and submit to repo etc...

As per the title: Using the image Armbian_22.11.2_Rock-5b_bullseye_legacy_5.10.110 Formatting an nvme ssd partition as BTRFS and running the armbian-install utility, install using SPI to boot, targeting ththe btrfs partition, and selecting BTRFS in the prompt results in a failure to boot. Reformatting that same partition as EXT4 and rerunning armbian-install (and making no changes to the data loaded to /de/mtdblock0) targeting the EXT4 partition, and the device boots using the SPI loader.

Hello everyone, I would like to thank @lurk101 very much for his patience in helping me how to boot Armbian directly to NVMe in my ROCK5B. I could do that with the Official release 22.11 Jammy with Gnome from the website. The PSU I am using is a dumb 5V 3A which I used to power my Raspberry Pi 4. As I could boot the OS directly from NVMe, I asked if he would mind if I shared the information with you. He answered he doesn't, so here we go... However, I was not able to use Ethernet port neither my wifi m.2 adapter, so there is no network connection... If I have more information I…

Hi, i just received my Rock 4 Se and a 32GB eMMC module today, and i'm currently not sure if the Image is incompatible, or if my storage modules are broken. I tried emmc standalone and SD for boot with nvme (from an dell notebook) for rootfs When i use the emmc, the filesystem goes into read only as soon as i do some apt upgrade. On reboot i often end up in initramfs nd have to fsck. I could gether some dmesg output: After this trace i get a lot of I/O Errors: Im not sure if this is an os or an emmc module issue. Any guess whats going wrong here? after that i coppied the current…

Getting free() invalid pointer issue when installing / using python3. Could be dpkg issue as well ! When I did sudo apt update && sudo apt upgrade, it happened and hence I tried to reinstall. This issue occurs when trying to manage it with ansible as well. I think something might be wrong with the latest python. Board: Helios64 (I know, I know CSC) Chipset: RK3399 Apt install logs: Reading package lists... Done Building dependency tree... Done Reading state information... Done 0 upgraded, 0 newly installed, 2 reinstalled, 0 to remove and 0 not upgraded. Need to get 0 B/472 kB of archives. After this operation, 0 B of additional …

Hello community, I am running Armbian taken from here on Radxa Rock 4c+. Everything I need seems to be in order (including wifi) but there appears to be no bluetooth device present (it is there using Radxa's images which have old kernels though). I tried to find out what could be the reason and noticed that dtb coming with Radxa has this: wireless-bluetooth { uart0-gpios { rockchip,pins = <0x02 0x13 0x00 0xd0>; phandle = <0xf1>; }; }; in pincntrl section and few other bluetooth/uart related bits while one coming with Armbian does not. I am not sure if this is the root cause and what the easiest way …

I have a Rock64, purchased in 2019, that has been running happily for 4 years. I was recently experimenting with hooking it up to a relay board and now I am unable to connect to the internet. I am unsure whether something is fried on the board itself or if this is a software problem I can fix, and unsure how to figure that out. Details I have learned more about relay boards now, so I'll do a few things differently and more carefully next attempt, but I had the 5v pin powering the relay board and the 3v pin, GPIO3_A4, and GPIO3_A5 connected to the control side to control two of the board's relays. When connected the Rock's power leds were still on, but eit…

Hi guys, in my job they bought a orangepi r1+LTS. i trying install armbian any version (last Debian and Ubuntu) but this don’t work. When boot system nothing happens… the led red still off and port Ethernet freezing(two lights on). Already installed Debian and Ubuntu of the official page orangepi, and system working without problems im using good sd card and official charger of the raspberrypi 4 How to solve this problem? In internet I don’t found much information thank u for read me

Hi FireFly station P2 on Armbian 22.11 Bullseye XFCE does not work on a 4K monitor. When turned on, ripples appear on the screen. Examples of images from links. The same problem at station M2. station m2 and station p2 do not work on a 4k monitor both

I deal with a problem I cant solve with installing my usb printer Samsung ML-2160. CUPS recognise it but it doesn't have the exact driver (it recomends ML-2152WPS I think, but it doesn't work as I cant print anything after the the installation) I tried from HP download directly a ULD but when I try to run the install.sh it gives a message about ARM architecture expected (although there is a directory for ARM architecture under the install.sh file) Any ideas?

Hello to everybody, I am using rock 5b, PCB Version 1.42 with Armbian 22.11 CLI. I would like to connect IQaudIO DigiAMP+ based on the TAS5756 (https://shop.max2play.com/en/iqaudio-digiamp.html). According to the GPIO pinout of ROCK 5b and the datasheet of DigiAMP+ (page 21), this seams to be feasible from the electrical perspective. But the software perspective overwhelmes me as a linux novice. If I understand it correctly, I need more or less two things: a device tree overlay to activate the appropriate GPIOs with their I2S and I2C functionality and to tell the kernel about the attached device (DTS file or the compiled D…

Hi guys, sorry if this question might sound stupid, but how do I open the M3 enclosure? There is no instruction in the manual, nor on the stationpc website. I just bought this little box and I am not sure if this has some screws or some other closing system. I can see the four rubber buffers on the bottom of the box, but I don't want to harm those without reason. Can anyone tell me how to disassemble the box? Thanks in advance.

Trying to build an image for a RockPi 4b. The build process runs all the way through until this. This happens on Ubuntu and Debian (both latest) and on both Cinnamon and XFCE (if that matters). I haven't touched any video settings! H

Hi, just got a Nanopi R5C (waiting for an RPi for more than a year, yet...) but I couldn't find any headless images for this little box. There's an official debian-image available running LDXE, but open media vault isn't able to run on an Desktop linux... Any chances there will be support for the Nano Pi R5C / Rockchip RK3568B2? btw: can't choose R5C or just 'others' from the drop-down when creating a new post...

Hello, I have had a nanopc-t4 and a few others for a long time now. I have tried to create a working dtb for it a few different times. My understanding of device trees is superficial I have not had good success. I have read the kernels DT docs many times. I can of course run an ancient 4.19 kernel but I would much rather be at the edge. Currently I've got armbian 22, but no edp. I can boot Friendly's lubuntu and then the edp works. Although it is edp or hdmi not both. I must unplug the edp to get the hdmi port to work. Which is really undesirable. If I remember, it can only enable 2 of its 3 hdmi ports at a time, so that is likely a simple DT c…

I installed the latest Armbian image and used a 1080P portable monitor to finish the install process. But when I use my bigger monitor with 2560x1440 resolution, it cannot output signal via HDMI. I searched about it, but most of them are about windows/x86 contents. Any idea about that?

I enabled spi-spidev through armbian-config but it does not show in the /dev/ directory. How do i fix this?

After 2+ years of hard work the fan of my M4V2 (in metal case with NVMe adapter) has stopped with specific burning smell. I ordered the same fan model (https://www.aliexpress.com/item/1005003989901083.html), replaced it and there is no rotation at all. Fan has been controlled by bash script from here: Has anybody got the same story? How it has resolved? My suspicions are on NVMe adapter, through which fan is powered - some draft scheme can be found, showing 5V/12V convertor and P-MOS switch: https://wiki.friendlyelec.com/wiki/index.php/NVME_SSD_Adapter_for_M4 SBC in this case works well w/o fan (~45 degrees of Celsius) during winter, but …

I am in the process to migrate a project from a Raspberry Pi 4B to a Rock Pi 4B+. Among others external devices shall be connected via WiFi AP, I2C, 1-Wire and UART to the Rock Pi. To emphasis, the system is running healthy on a Rasberry. I managed to get WiFi AP and 1-Wire up and running on the Rock Pi. Now I got stuck with UART/UART4. Armbian 22.11.1 Bullseye with Linux 5.15.80-rockchip64 I enabled UART4 via Armbian-Config. Therefore, /boot/armbianEnv.txt shows: ... overlays=i2c7 uart4 w1-gpio param_w1_pin=GPIO4_D6 param_w1_pin_int_pullup=1 ... I can take a jump wire and bridge the TX-pin (GPIO1_B0, Pin#19) and RX-pin (GPIO1_A7, Pin#21). W…

Hello, when i installed the helios64 initially i had the problem with the fans spinning at 100% (or really loud) and i solved it somehow. It was working fine with the fans spinning for one second when starting and shutting down the device. Now i finally updated the NAS with sudo apt update sudo apt upgrade sudo omv-release-upgrade sudo reboot and after the reboot the fans are now spinning really loud again all the time. Is anyone aware of an easy solution or a quick fix? Someone else had the same problem at https://forum.openmediavault.org/index.php?thread%2F42550-fans-go-on-full-and-stay-there-after-doing-an-update-in-omv-web-control-panel-he%2F= but it…

Hello, Some weeks ago, I installed the "under development" version. File was named Armbian_22.11.0-trunk_Odroidm1_kinetic_edge_6.1.0-rc5.img.xz Now, I see that the "advertised" version is a rolling release armbian 22.11 Jammy. Based on this (https://wiki.ubuntu.com/Releases) page kinetic is an earlier version than jammy. If I scroll down the page ( https://www.armbian.com/odroid-m1/ ) , I see a kinetic rolling weekly release. I suspect that the kinetic is an unstabled release while Jammy 22.11 is. Please can you confirm/explain? If yes, is there a way to "downgrade" to the stable version? Thanks …

Hi just a quick question What package is dt-bindings normally located in, i would assume kernel headers but i tried installation via armbian-config and couldn't see them. Can anyone confirm what package it normally is in or was i blind thanks. Was just working on adding support Waveshare Dual RS232 on SPI2, uploaded DTS to https://github.com/radxa/overlays/blob/main/arch/arm64/boot/dts/rockchip/overlays/rk3399-spi2-sc16is752.dts Atm i hardcoded the defines on machine but not ideal if it changes in the future Thanks

Booting from SD card as well Trying make emmc bootable 1. nand-sata-install 2. select "Booting from emmc" 3. No errors 4. reboot 5. Booting. UART console find part: trust_a OK find part: uboot OK Trust Addr 0x8000, 0x0 Addr 0x8000 No find trust.img! Error verifying slot_a find part: trust_b OK find part: uboot OK Trust Addr 0xa000,0x8400, Addr 0xa000 No find trust.img! Error verifying slot_b Next info got after boot from SDcard armbianmonitor -u https://paste.armbian.com/hodunasano mmcblk2 - eMMC lsblk …

How do I use a camera that I have connected through the connector on the board? I tried running armbian-config but did not find anything about a camera.

Hey all. Running the Dec 9th build of Armbian 22.11.2 Debian Bullseye CLI, and I've been running in to issues with consistently remotely connecting to the board. While ssh and other direct connections (IP:Port for services like Nextcloud, etc) work for a bit after a recent reboot, after some unknown amount of uptime I'm unable to connect to the board through any new remote connections. Attempting an SSH session provides me the error ssh: connect to host 192.168.50.5 port 22: No route to host When connected via the serial console, I am able to verify that the board has internet access while it is refusing these remote connections on the local netwo…

I have forgotten my user password. How to reset it? I have pressed SHIFT (LEFT, RIGHT) during many system boots but GNU GRUB has not been displayed even once. Therefore this instructions don't help me: https://www.youtube.com/watch?v=H9jjm81-nFg

Hello, If I unplug my M1 for the whole night. When I power up It does not start the first time. It stays stuck on the hardkernel splashScreen. If I power cycle, it starts as it should. I'm booting on the SD card and system is on nvme. System is up-to-date. Do you have any idea of what may happen? Thanks Julien

Hi Team, i have a lcd touchscreen android rockchip rk3288 ( armeabi-v7a ) and i want change the OS with armbian and install it on sd card , which image that should i use? regards, Adrian

I tried the "Armbian_22.11.1_Rock-5b_bullseye_legacy_5.10.72.img.xz" image on my Rock 5B. It worked on an SD card, but when I loaded it on an NVME drive on the build in M.2 slot, it worked with neither the SPI Boot image with armbian-install.sh, nor the SPI image from radxa. When I have SPI loaded, and I have the SD Card installed, it just seems to load from the SD Card. When I remove the SD card, and boot the system. It seems to just stay with the LED with the blue and green elements on. I've waited several minutes without it booting. I was able to get it to successfully boot once, but never again.

Hi, I've flashed the Armbian SPI image following these instructions: https://wiki.radxa.com/Rock5/install/spi I've flashed this image: Armbian_22.11.2_Rock-5b_jammy_legacy_5.10.110_gnome_desktop.img.xz to a M.2 NVME SSD I own a DVB-S2 USB 2.0 device from PCTVSystems: https://www.linuxtv.org/wiki/index.php/Pinnacle_PCTV_DVB-S2_Stick_(461e) currently working in a RPi4 with OSMC. Firmware file (dvb-demod-m88ds3103.fw) is on /lib/firmware When I connect it to Rock5b I can see it with lsusb command Bus 002 Device 003: ID 2013:0258 PCTV Systems DVB-S2 Stick 461e and dmesg usb 2-1: new high-speed USB device number 3 using ehci-pla…

I don't know where else to share this so I'm putting this here. The board recognizes and tries to the load the driver for an AR9462 QCNA222 M.2 WiFi card, but fails. I tried a custom build found on Radxa forum/github, built Armbian myself, and tried an official build. All resulted in the same error. Card was tested and working correctly on 2 different Debian x86 machines. lspci 0000:00:00.0 PCI bridge: Fuzhou Rockchip Electronics Co., Ltd Device 3566 (rev 01) 0000:01:00.0 Network controller: Qualcomm Atheros AR9462 Wireless Network Adapter (rev 01) 0002:20:00.0 PCI bridge: Fuzhou Rockchip Electronics Co., Ltd Device 3566 (rev 01) dmesg ath…

I get static noise on the analog audio out when no sound is playing (I use alsa). I tried to add a configuration file in /etc/modprobe.d which disables power saving (as this appears to be the usual reason for static noise), but this does not work. Does anyone know how to resolve this?

Dear to all, I'm new on linux environment so be patience with me. I have a helios64 unit with installed Openmediavault 6. When I reboot or turn-off helios64 (both from webgui interface that from power button) the hard disk ( 2 wd60efrx) make a cute sound from head. How can I check that heads are parked correctly? I don't want damage my hard disks Best regards

Hello I just installed armbian (Gnome) on my NVME and all seems to work great (without SD card). So, the first issue I have is the resolution of the screen. I add 2560x1440 (1920x1080 was the maximum before) but the test in this mode not working. I think the cause is than I copy/paste the mode from a post on internet. In fact, cvt is not installed and impossible to calculate mysel the vesa CVT modline. How can I install CVT ? bash: cvt: command not found Thanks a lot Anakin

A test version of Armbian images to run from NVMe without having to write the curve of the official u-boot version to SPI (which breaks the launch of other systems from SD cards and other media). The whole system works completely with NVMe . https://disk.yandex.ru/d/V5AxXNN2yJnOfg The installation of the system on NVMe and u-boot in SPI was checked using the standard tools of the armbian-config utility. Everything works correctly. Also in this new u-boot, the ability to start the system in EFI mode is available. To install a system with EFI\grub on NVMe. Install a new bootloader in SPI. Start the system from the SD card and burn …

Hi, I own a nanopi m4 v1, I know there is no more armbian support neither maintainer for this board but I still enjoy "the other supported variants" which work very good for my needs. Until now, I only used armbian on sdcards for my system, but today I tried to install it of my emmc module. Maybe I did somethig stupid, I tried to install the bullseye current cli version from https://www.armbian.com/nanopi-m4/ on my emmc module via armbian-install. So all process of installation was ok (boot on sdcard then armbian-install => erase / format / install on emmc ...), I choose to boot from emmc too (maybe it was a mistake). => After …

Hi guys, I am building armbian image for rockpi4b+ and its kernel is 6.0.11(edge version) and the bluetooth failed start up. If anyone knows what kernel 6.0.11 did that cause the problem: wzkiro@rockpi-4bplus:~$ dmesg | grep brcm [ 7.069061] brcmfmac: F1 signature read @0x18000000=0x15294345 [ 7.108688] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43456-sdio for chip BCM4345/9 [ 7.109142] usbcore: registered new interface driver brcmfmac [ 7.236547] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43456-sdio for chip BCM4345/9 [ 7.245940] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/9 wl0: Feb 11 2020 11:54:51 version 7.45.96.61 …

Howdy, Just wanted folks to know that debian bullseye is generally getting what I need done. Specially Welcome to Armbian 22.11.1 Bullseye with Linux 5.10.72-rockchip-rk3588 is working. It is working headless just fine. Now what is not working for me. The HDMI is not showing up at all. Between my KVM and ultra wide monitor it may not be an OS issue. SD-card boot is the way I am going. Manual partitioning of the NVME was needed to install. It felt like I needed to reboot a few times to get the NVME to boot. Overall it was a better experience than the experience on the Firefly station P2 competing with Station OS. Thanks…