Other families

Been dreaming of this one for a while. Finally got a weekend to focus on it recently. I'm hoping someone is eager to take what I've done and move It along some more. Here's what we have so far. * a linux 'family' called virtual.conf * a kernel config called linux-virtual-current.config * a board called virtual-qemu.wip The result is a full HVM accelerated armbian image with a kernel compiled with all the virtio drivers for disk, network and video. Also a u-boot.bin made for qemu that can boot the image when used as the qemu bios/firmware I've ran it as a VM on ubuntu using plain qemu on a Ampere eMag box.. and using UTM (qem…

Good news. Thanks to the work of many, there is now a real opportunity to run the Armbian system with the main core on Jetson Nano, and more importantly, it is easy to integrate the image build process into the official GIT Armbian. In the near future, I plan to post ready-made images with the latest kernel 5.10.22 on the download site. To run them, you need to update u-boot to Jetson Nano. This is very easy to do, just run the latest official version of Ubuntu for Jetson Nano from the SD card, it will update itself in SPI (?) u-boot to the latest version (2020.04), after that you can run Armbian from any SD card or USB media. The new u-boot supports automatic syst…

To Igor Bit not understand why new 5.44 for nanoPC T3 plus not run. I see only first boot screen and then black always ???

Hi, After a power shutdown, my Cubox-i 4 Pro does not boot anymore. I am running on it Debian Stretch since years. My system is on a hard drive (/dev/sda1). It seems that the boot process is blocked in a loop, as each time, just after: Starting kernel ... Uncompressing Linux... done, booting the kernel. ...U-boot is restarting as after a fresh reboot. My boot.txt: $ more armbianEnv.txt verbosity=7 rootdev=/dev/sda1 console=serial usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u Here is the bootlog: U-Boot SPL 2013.10-rc4-ge4bc4c3 (Dec 18 2014 - 14:55:42) Boot Device: SD1 spl: error reading image u-b…

Hi, Beside some limitations with cubox's hardware I love my cubox-i 4x4. But it is hard to find good documentation about how to many things. Reading this forum and other webs I made many of my goals. After installing Debian from this web site and using the nand-sata-install script the system works from the hard drive. This hard drive has two partitions, the main and big one and one small, 4GB, swap partition, but the system is not using it, so I would like to know if I can make the system use it. I found this how to: 9. Setting Up Swap Space 9.1. Swap Files Normally, there are only two steps to setting up swap space, creating the partition and adding it to /etc/…

Hi, My Solidrun Cubox I1-300-D has been running Armbian for quite some time (Samsung EVO SD card). However, I tried to update/upgrade, and my version was non-supported anymore (19.04?), so time for a fresh new image. I've tried three times (download image from https://www.armbian.com/cubox-i/, sha256 check, burn image with etcher, inspect file structure (looks good), and boot), but each time this happens: "Armbian universal operating system" + text ("Executing script at ...") splash screen, then a black screen, and then my TV says "no signal", and then nothing anymore. At the ethernetconnector, there is red LED on / flashing…

The alpha version of Armbian images for Orion O6 is available. To launch, burn to a USB flash drive, connect to Orion O6 and turn on the power (installation on NVMe has not yet been verified). The system starts automatically. Important. Image output to the monitor works only in graphical mode (in images with DE). Console output currently only works in UART, so you need a UART console or SSH connection for initial startup. Launching the desktop and displaying the image on the screen can take 30-80 seconds, depending on the speed of the media. https://disk.yandex.ru/d/gedMM0eLiURrjA Armbian-unofficial 25.05.0-trunk Noble ttyAMA2 orion-o6 …

Upgrading cubox-i Armbian Buster from kernel 5.7.x to Kernel 5.8.y breaks ethernet and I'm unable to get it connected again. Works fine again downgrading back to 5.7.y. This occurs on multiple cubox-i devices. System diagnosis information will now be uploaded to http://ix.io/2zH6 dmesg | grep eth0 [ 4.667327] fec 2188000.ethernet eth0: registered PHC device 0 [ 22.369472] fec 2188000.ethernet eth0: Unable to connect to phy nlcli wlan0: connected to sketch-wlan "Broadcom BCM4330" wifi (brcmfmac), 6C:AD:F8:1D:36:25, hw, mtu 1500 ip4 default inet4 10.1.0.41/22 route4 0.0.0.0/0 …

I am currently using Solidrun SbC (ICUBOX and HUMMINGBOARD) and a couple of weeks ago I updated UBUNTU on the Hummingboard to release 18.04 and lost internet..no more network. So try to fix that with no success so after many hours I decided to rebuild the OS with Armbian Buster but I cannot boot from my sd card (sd was flashed with Etcher). So did a surface check with no problems found. I thought it was power supply but I can boot from Android (Cubox and Hummingboard ) so PS should be good. My sd cards are Sandisk extreme 16 gigs. Since I did not build a bootable sd card since 3 years ago, I must have done something wrong but I don’t know what? Does the sd has to be form…

Sorry to be back here I run a Cubox-i. I upgraded to kernel 5.1.16 yesterday. Then I rebooted and everything was running fine. But today my server looked dead: none of my services was answering, no way to ssh to the cubox... I tryied a hard reboot with no success. Here is the log on a putty console: U-Boot SPL 2013.10-rc4-ge4bc4c3 (Dec 18 2014 - 14:55:42) Boot Device: SD1 spl: error reading image u-boot.img, err - -1 Load image from RAW... U-Boot 2013.10-rc4-ge4bc4c3 (Dec 18 2014 - 14:55:42) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Board: MX6-CuBox-i DRAM: 2 GiB MMC: FSL_SDHC: 0 *** Warning - b…

Hi Igor, I want to compile a new kernel on HB. I do following steps: export ARCH=arm export CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf- make imx_v7_cbi_hb_defconfig make If make is in process, I become an error: /bin/sh: 1: /usr/bin/arm-linux-gnueabihf-ld: not found make[1]: *** [init/mounts.o] Error 127 make: *** [init] Error 2 how can I fix that?

Hi all, This is my first post! My cubox-i4x4 won’t boot with a second usb device plugged in. I am running the latest version of Armbian Jessie (Vanilla Kernel). I have done “nand-sata-install†booting rootfs from usb flash memory. Someone having a clue?

Hi everyone, Armbian works well for me on a NanoPi Neo, and installing it on my Cubox i4 was straightforward... but I'd like to try a kernel newer than linux-image-cubox (version 4.14), to get improved video support, and both linux-image-dev-cubox (version 5.2.11) and linux-image-next-cubox (version 5.1.16) do not provide any video output at all. I've uploaded the armbianmonitor report from booting the linux-image-dev-cubox kernel. Help on this would be appreciated!

[WIP] Schematics Pros: - board vendor provides dev samples and documentation - working with latest mainline kernel - many variants by the same vendor - official SDK/BSP currently on 4.4 - no unreliable shitty Micro USB for DC-IN but GPIO by default Cons: - new platform needing more initial work - not many active developers

Hi every one, Im new on this form and this is my first time, when Im working with HummingBoard. On my HummingBoard is connected a little board with HDMI input and is connected with DVD Player. One another HDMI, which is on HummingBoard, is connected with Monitor, where I can see my console. So, my question is, how can I install, that my little board will become a video from DVD Player and streaming it to the HummingBoard, so, that I can see this video on my Monitor. Im using the Debian wheezy image Sorry for my english, hope for fast help

Hello, I wanted to test wireguard with my cubox i4, but I'm not able to load the module. I tried to search the net for this error, but fond nothing useful. Maybe someone has an idea. Thank you Michael uname -a Linux loki 4.19.41-cubox #5.85 SMP Wed May 8 15:52:55 CEST 2019 armv7l GNU/Linux dpkg -l | grep linux ii console-setup-linux 1.164 all Linux specific part of console-setup ii libselinux1:armhf 2.6-3+b3 armhf SELinux runtime shared libraries ii linux-base 4.5 …

Hello I downloaded Armbian for a CuBox i4P from https://redirect.armbian.com/region/EU/cubox-i/Bionic_current_desktop. uname -a reports: Linux cubox-i 5.10.12-imx6 #21.02.1 SMP Wed Feb 3 21:02:35 CET 2021 armv7l armv7l armv7l GNU/Linux However this image is working really fine, for a 7yo hardware. Thank you, Developers 2D software rendering is fast, Desktop windows are transparent. Great work! I tried Armbian Focal desktop mainline first, but it didnt show the desktop never again after first reboot, so i was happy with Bionic! Found similar problem here and i think i just need the correct xorg driver. Thanks for a…

I've been looking for a way to rotate the display and change the resolution on the Hummingboard running the Debian image I did this from the FAQ: screen resolution: nano /boot/boot.cmd # example: # change example from # disp.screen0_output_mode=1920x1080p60 # to # disp.screen0_output_mode=1280x720p60 mkimage -C none -A arm -T script -d /boot/boot.cmd /boot/boot.scr somewhat blindly and I destroyed the boot.scr, further searching found that /boot/boot.cmd doesn't exist... I've been messing with xorg with no avail. I think that this is the way to do, through the boot.scr, but there…

Maybe I missed something, it's been a few weeks since I needed to install an image. cubox with hdmi does not boot. There is no serial port, so I can not even try to figure it out. Also it never requests an ip address from the router. Tried with trusty legacy and vanilla. Used the link specifically labeled cubox-i http://www.armbian.com/cubox-i/

Hi, I am running Debian Strech on a headless server with armbian (since 2014 on wheezy), on a Cubox-i 4 Pro. My system is on /dev/sda1 After an upgrade, few minutes ago, my device is no more reachable by ssh neither answering to ping. It seems to boot the kernel but I am not even sure of that (as nothing appears in the console after "booting the kernel"). Here is the full console log: U-Boot SPL 2013.10-rc4-ge4bc4c3 (Dec 18 2014 - 14:55:42) Boot Device: SD1 spl: error reading image u-boot.img, err - -1 Load image from RAW... U-Boot 2013.10-rc4-ge4bc4c3 (Dec 18 2014 - 14:55:42) CPU: Freescale i.MX6Q rev1.2 at 792 MHz R…

Hello and first off thank you for the great resource of information and downloads. I am having problems booting up a fresh image on my cubox i 4 pro. The last time i installed an Armbian Image was in 2014 when i got this wonderful little machine and while trying upgrading my own cloud to next cloud i got a bad big block so i thought lets put a fresh image on and now its been 2 days of time outs. The Solidrun logo comes up and then i see that it can't find any images, well i have pictures so there it is. I used etcher to make the sd card. I used the official sd card formatter. New SD card is 32 GB transcend 10 speed. In my router the cub…

Not sure if this should go in this section, but since my problem is about non-supported board, then I guess... I found out about Armbian only recently and decided to give it a try for my T113-S3 based board I bought on Aliexpress. It looks like it's some kind of a MangoPi MQ clone, at least judging by schematics. I managed to create a new configuration for my board, together with required U-Boot patches. I built two images, for "current" and "edge" kernel. For some time I was under impression that Linux doesn't boot at all (serial console output was stuck at "Starting kernel ..."), until I added earlycon=on to armbianEnv.txt. Then I finally saw some outpu…

Hi, I've just created a SD-card with Armbian Bionic (mainline kernel 4.19.y) for a Hummingboard Gate. I noticed during boot that it says it uses U-boot version 2013.10-rc4. This seems quite old compared to the 2018 version that was on the Debian Stretch image from SolidRun. I've tried to search the internet to see what the impact of something like this is and wasn't able to find something that made sense to me (could be entirely my fault). I therefore have the question: Is the U-boot version intentional? (maybe it has some features that newer versions have dropped.)

while checking the state of systemd I encountered systemctl is-system-running degraded with systemctl --state=failed UNIT LOAD ACTIVE SUB DESCRIPTION ● systemd-modules-load.service loaded failed failed Load Kernel Modules and in /var/log/messages Nov 21 12:52:54 localhost ker…

Hi, I had downloaded the image for my Hummingboard i2ex & tried to move my root FS to a USB drive. It did not throw any errors, but, on verifying the mount & boot.cmd file, it did not get migrated. The root still shows mounted from the SD Card. Can anyone help me in resolving this issue ? Here is my device details after reboot. root@cubox-i:~# lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT sda 8:0 1 14.6G 0 disk └─sda1 8:1 1 14.6G 0 part mmcblk0 179:0 0 14.9G 0 disk └─mmcblk0p1 179:1 0 14.6G 0 part / root@cubox-i:~# blkid /dev/mmcblk0p1: UUID="77646057-ce1f-426f-b09b-d2e6f03f3d52" TYPE="ext4" PAR…

I installed Armbian_5.59_Cubox-i_Debian_stretch_next_4.14.66 on my Cubox-i. Boots nicely, but ethernet is not working. The ethernet cable/connection is working, because the cable does work via and ethernet-to-usb connector to the same cubox. EDIT: Oh, I must say that ethernet-to-usb is fast etnernet, not GigE /EDIT Dmesg included. Plus dmesg | grep network stuff. Tips how to proceed? root@cubox:~# cat dmesg.cubox.no-eth.txt | grep -i -e eth -e netw [ 0.793426] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator [ 0.806213] fec 2188000.ethernet eth0: registered PHC device 0 [ 10.900568] A…

I just switched from iptables to netfilter. After a reboot I get this kind of status for the service systemctl status nftables ● nftables.service - nftables Loaded: loaded (/lib/systemd/system/nftables.service; enabled; vendor preset: enabled) Active: failed (Result: exit-code) since Fri 2019-07-12 16:04:59 CEST; 4min 28s ago Docs: man:nft(8) http://wiki.nftables.org Process: 287 ExecStart=/usr/sbin/nft -f /etc/nftables.conf (code=exited, status=3) Main PID: 287 (code=exited, status=3) Jul 12 16:04:59 cubox nft[287]: netlink.c:62: Unable to initialize Netlink socket: Protocol not supported Warning: Journal has been rotated since unit was…

Hi, Is there anyone out there who could explain why I cannot do any upgrade on my Cubox i4 anymore? On boot it looks like this: [ 0 security updates available, 9 updates total: apt upgrade ] Last check: 2017-11-26 04:06 Thanks!

Hi. I have a bunch of HummingBoard2 boards that have been used by a company called Vivo. Basically they allow schools to transfer video through Ethernet to monitors and projectors. I also want to do this but Vivi is a subscription based system so that SUX! I therefore want to blow Vivi away and load a clean Armbian. My issue is that the boards have no SD cards soldered to the board. They have power, 2xUSB, RJ45, HDMI connectors. They must therefore boot from eMMC. I found info on the board manufactures website., SolidRun, on how to use jumpers to select boot type. It was set to eMMC so I set it to USB and flashed a SD card with Armbian 20.20 and rebooted…

Hi! For some reason my nanopi fire 3's gigabit ethernet is very unstable. When connected to my local machine directly, the ping latency is insanely high and irregular: PING 10.42.0.101 (10.42.0.101) 56(84) bytes of data. 64 bytes from 10.42.0.101: icmp_seq=1 ttl=64 time=112 ms 64 bytes from 10.42.0.101: icmp_seq=2 ttl=64 time=333 ms 64 bytes from 10.42.0.101: icmp_seq=3 ttl=64 time=350 ms 64 bytes from 10.42.0.101: icmp_seq=4 ttl=64 time=203 ms 64 bytes from 10.42.0.101: icmp_seq=5 ttl=64 time=1014 ms 64 bytes from 10.42.0.101: icmp_seq=6 ttl=64 time=423 ms 64 bytes from 10.42.0.101: icmp_seq=7 ttl=64 time=93.4 ms 64 bytes from 10.42.0.101: icmp_seq=8 ttl=64 time…

Hello, I use a SolidRun MicroSOM i2eX in combination with the Toshiba TC358743 HDMI to CSI-2 bridge. (http://www.toshiba.com/taec/components/ProdBrief/10L02_TC358743_ProdBrief.pdf) As far as I know, the driver for the Toshiba chip is now included resp. available in kernel 4.1. (https://lwn.net/Articles/643374/ and http://www.spinics.net/lists/linux-media/msg88921.html) Can anyone confirm that? The driver was available for kernel 3.0.35 (https://developer.ridgerun.com/wiki/index.php/Toshiba_TC358743_Linux_driver_for_iMX6) I've created a new image based on the compile.sh script from Igor PeÄovnik (https://github.com/igorpecovnik/lib). Thanks a lot fo…

Hi I have no /dev/dvb on my UDOO Quad. I'm trying to get MythTV or tvheadend working on my UDOO Quad with Armbian Jessie with kernal 4.4.102 glen@udoo:~$ uname -a Linux udoo 4.4.102-udoo #2 SMP Fri Nov 24 18:49:01 CET 2017 armv7l GNU/Linux I thought that dvb drivers were included in version 3.19 of the kernel and up? Anyway I copied dvb-usb-af9015.fw to /lib/firmware and rebooted. But nothing shows up under /dev/dvb/ I would expect there to be adapter0 and adapter1 Here is my lsusb: glen@udoo:~$ lsusb Bus 001 Device 004: ID 13d3:3226 IMC Networks DigitalNow TinyTwin DVB-T R…

i have already install pihole + unbound on this device now i want to reset everything so i can make a new project on it because of the limitation on storage.. can i know how to do that? and without change any kernel/firmware i'm beginner on linux ecosystem...

Hey All - So I decided to upgrade my Udoo from 4.5 (Debian Jessia, kernel 3.14.28) to the latest 5.25 Xenial. I gave next (4.4.46) a try, and it seemed to work awesome, however it seems like no one wants 1wire (still - it only takes up 1 gpio!). I built custom kernels enabling 1wire in the kernel and updated (or for default adding) 1wire to be enabiled in the imx6qdl-udoo.dtsi, however after I install the kernels, it just sits indefinitely at the red Armbian logo on boot. On 4.4.46, i was able to just install all the debs via dpkg -i *.deb On 3.14.56, I had to use dpkg --force-all -i *.deb Any ideas on what I'm doing wrong? Its been a while, so I'm s…

Hi there, is there a chance to have hardware acceleration for the armbian images for stretch? I build the debian stretch default desktop version, but there is no xserver-xorg-video-imx-viv and thus the desktop feels really laggy. Regards Georg

Hi, I'm using the debian jessie v2.9 image, I've mistakenly used an 8GB SD card and setup my system now, I would like to move this to a larger SD card, I can DD the image to a new card, is there boot scripts that I can force to re-run to resize the partions? Thanks, Jack

Hello everyone, just wanted to let you know, upgrade from Armbian Ubuntu 5.38 to 5.44 caused problems on my Cubox-i4Pro. - Armbian Ubuntu 5.38 headless (no display connected to Cubox-i) worked perfectly, there were no issues with anything. - Upgraded Armbian Ubuntu 5.38 to 5.44 (apt-get) and rebooted - After reboot, no audio was sent to my audio amplifier (through Toslink optical cable) by Shairport-Sync 3.1.7 (AirPlay emulator). Airplay was visible on my iOS devices (iPad, iPhone) and audio was streamed from iOS to AirPlay, but no audio was sent by Cubox-i to the optical connection to my audio amplifier. - Removed the Shairport package usi…

Hello all, I've downloaded the Vanilla Jessie (Armbian_5.00_Cubox-i_Debian_jessie_4.4.1.zip) and installed it on my 2 Cubox-i (i4Pro and i4x4). I'd like to get Wi-fi working on both and edited the /etc/network/interfaces file to uncomment and configure wlan0 and rebooted. Unfortunately on both, I'm unable to get Wi-Fi operational. Performing an ifup wlan0 generates the following output: wpa_supplicant: /sbin/wpa_supplicant daemon failed to start run-parts: /etc/network/if-pre-up.d/wpasupplicant exited with return code 1 Failed to bring up wlan0. Any guidance would be greatly appreciated. Thanks in advance UPDATE: WiFi is now working on both 4x4 …

Hey, i'm getting the following error, when i try to login me as root: Authentication token manipulation error This error appears after i insert the first time the new password. I think this is an error in the Debian Image, isn't it ? Best Regards Pingbo

UDOO Quad Hello. Armbian bionic desktop mainline based kernel 5.4, USB ports do not work, wifi module is not visible. Everything works correctly on Stretch. Do not tell me where to look for the reason?

I just ran apt-get update && apt-get upgrade, sure enough, a new kernel was downloaded. Due to a non-standard wifi chip, I always run KMS before rebooting, giving the new kernel version as an argument. (The automatic install on reboot didn't work so well in the past) It seems now that something is not right with the new kernel headers. I have not rebooted yet, out of fear the system might be unstable then. Log: http://ix.io/1djM Compiling scripts: /usr/src/linux-headers-4.16.8-cubox# make -s scripts scripts/selinux/genheaders/genheaders.c:19:22: fatal error: classmap.h: No such file or directory #include "classmap.h" …

Just wondering if anyone has booted the latest cubox-i test images with kernel 4.9.5 ? I tried the last couple of days with no joy; however I have not got around to full logs / troubleshooting. It looks like it is getting into u-boot OK but then not finding the dtb and drops to the u-boot shell.

Hi there, the attempt to mount an smb-share does not work. The attempt ends with the messages mount error: cifs filesystem not supported by the system mount error(19): No such device Refer to the mount.cifs(8) manual page (e.g. man mount.cifs) The output of uname -r is 4.13.16-cubox cifs-utils are installed. Am I missing something here? Thanks in advance, Christoph

Hi Igor, my Cubox-i4Pro worked perfectly fine with your Armbian Debian Jessie, until I upgraded from 4.7 to 4.81. After the upgrade was performed today, the system time is always wrong after boot, it is always set to Jan 1 01:00:00 1970. Setting the system time correctly does not help, after reboot it is wrong again. I didn't observe this behavior before upgrade, the system time just used to work without any attention needed. Nothing else was changed in the system, only the upgrade of Armbian was done to ver 4.81. So I'm wondering what went wrong with the upgrade. Hardware time is always correct, syncing system time to hardware time does not survive boot. I tried …

Hi, how can I edit the ssh welcome message in my cubox? Thanks.

I just stumbled across usr/src/linux-headers-4.19.20-cubox$ make scripts scripts/kconfig/conf --syncconfig Kconfig net/Kconfig:89: can't open file "net/wireguard/Kconfig" scripts/kconfig/Makefile:69: recipe for target 'syncconfig' failed make[2]: *** [syncconfig] Error 1 Makefile:539: recipe for target 'syncconfig' failed make[1]: *** [syncconfig] Error 2 Makefile:635: recipe for target 'include/config/auto.conf' failed make: *** [include/config/auto.conf] Error 2 Workaround was to comment this source-statement grep -i wireg net/Kconfig source "net/wireguard/Kconfig"

Hi, I'm trying to build the next kernel (4.14.y) for Cubox-i, but the process fails here: DTC arch/arm/boot/dts/imx6dl-cubox-i.dtb Error: arch/arm/boot/dts/imx6qdl-cubox-i.dtsi:261.1-9 Label or path vcc_3v3 not found FATAL ERROR: Syntax error parsing input tree scripts/Makefile.lib:317: recipe for target 'arch/arm/boot/dts/imx6dl-cubox-i.dtb' failed make[1]: *** [arch/arm/boot/dts/imx6dl-cubox-i.dtb] Error 1 arch/arm/Makefile:348: recipe for target 'dtbs' failed make: *** [dtbs] Error 2 make: *** Waiting for unfinished jobs.... When I compiled the kernel approx. 2 months ago (4.15.?) I did not get that error. Any ideas?

With build from 26th of August, kernel 3.14.14 (cli, debian jessie) I cannot see any hdmi output. When cubox i4pro boots, it shows uboot env and I can interrupt boot, hdmi works well. starting kernel puts monitor into powersave mode. everything else seems to work, I can ssh to the cubox and see the logs, which look normally, e.g. I have tried bpp 16 or 24 when default 32 didn't work root@cubox-i:~# egrep 'mxc|hdmi|fb0' /var/log/kern.log Jan 1 01:00:20 localhost kernel: [ 0.000000] Kernel command line: root=/dev/mmcblk0p1 rootfstype=ext4 rootwait console=tty1 video=mxcfb0:dev=hdmi,1920x1080M@60,if=RGB24,bpp=16 rd.dm=0 rd.luks=0 rd.lvm=0 raid=noautodetect pci=…

Hi, i've asked this question also in the solid-run forum, but i think it's important to ask here also to Igor. Must be an explanation to from where the nvram file came out first. There are different brcmfmac4330-sdio.txt sources, with very different files for same wifi adapter and device (Cubox-i) I'm wondering what is the difference from the nvram .txt file for broadcom wifi firmware (brcmfmac4330-sdio.txt) between (A)solid-run:meta-solidrun-arm-imx6 (much longer with lots of additional parameters)https://github.com/SolidRun/meta-solidrun-arm-imx6/blob/fido/recipes-bsp/broadcom-nvram-config/files/solidrun-imx6/brcmfmac4330-sdio.txt (B)the one that ships …

Its been a while since I built a UDOO image (need another kernel module), when I ran compile.sh, it pulled new source and told me to clone a new build directory. In the process of cloning, however with UDOO being EOS, is it still possible to build the legacy kernel/image with current sources?

Hello, I have a problem with connecting to ILI9341 hummingboard postaebuje as described http://docs.armbian.com/Hardware_Freescale-imx6/ I do entry Add this to your / etc / modules: fbtft_device name = adafruit22a rotate speed = 90 = 48000000 fps = 50 GPIOs reset = 67, led 72, dc 195 busnum = 1 reboot but the display is lit only shows nothing What may be the problem wyśietlacz exactly http://allegro.pl/wyswietlacz-lcd-tft-2-4-240x320-spi-bte-141-i6258585811.html

I am looking for ways / support to run Armbian (no release preference; any version would be good) on the tolino epos 1 eInk display eBook reader (built by taiwanese manufacturer Netronix under model ID 37NB-E70Q2M+4A2). The device currently/by default runs Android 4.4.2. I'm able to flash customized 4.4 images via fastboot and have ADB control (Android Debug Bridge) via USB and Wifi. I've identified the following key components: Freescale i.MX6 SoloLite (MCIMX6L8DVN10AB) CPU. Version with GPU and EPDC (Electrophoretic Display Controller; a feature-rich, low power, and high-performance direct-drive, active matrix EPD co…

Hi community I have a HummingBoard2 and installed Armbian on SD (first boot device). And everything works really fine! !!!Thanks a lot for the perfekt installation routine!!! Afterwards i tried to install from SD to eMMC with the "sata-nand-install.sh" script. Installation completes without errors. If i boot with inserted SD card the system boots from SD without errors (for a fused (0x5=2840 and 0x6=10) IMX6Solo and also with unfused module) - fine! If i remove the SD card and use a fused (0x5 = 3040 and 0x6=10) IMX6Solo module, i think it tries to boot from eMMC but it doesn't work. When i try to boot with inserte…

I've loaded Armbian onto my Udoo Dual and am having issues getting it past starting the kernel. I really like this OS on my other sbc's and have had no issues before this. I'm mostly a Linux noob with an elementary grasp of compiling the kernel. I have had this problem for about a week and am finally asking the pro's on how to fix this. Any help would GREATLY appreciated. Below is what I get from the U-Boot startup. Thanks! U-Boot SPL 2015.10-armbian (Jun 13 2017 - 15:51:16) U-Boot 2015.10-armbian (Jun 13 2017 - 15:51:16 +0200) CPU: Freescale i.MX6DL rev1.1 at 792 MHz Reset cause: POR Board: UDOO DualLite DRAM: 1 GiB MMC: FSL_SDHC: 0 *** Warning - bad CRC,…

Greetings; I have downloaded this https://dl.armbian.com/cubox-i/Noble_current_server and verified that I got what I was supposed to (ASC, SHA). I have used a brand new usbimager to install it on various freshly formatted (brand new SD Formatter) and verified working Samsung Evo 32GB, SanDisk Extreme Plus 16GB, Extreme Plus 32GB. All the formatting, imaging and installation done on an Ubuntu 25.04 laptop. After usbimager is done, if I use the Ubuntu Disks application to look at the drive, the first partion shows as free space, which seems suspicious. When I insert the newly-set up SD cards in the Cubox-i4, I see …

Hello, I'm trying to get the gstreamer pipeline to work with the i.MX h.264 hardware encoder and decoder. I've installed Trusty Vinilla http://mirror.igorpecovnik.com/Armbian_4.90_Cubox-i_Ubuntu_trusty_4.4.1.zip on a Hummingboard-Gate and followed the instructions for setting up the i.MX Gstreamer plugins here: https://github.com/Freescale/gstreamer-imx/blob/master/docs/debian-ubuntu.md gst-inspect-1.0 reports... $ gst-inspect-1.0 | grep imx imxvpu: imxvpudec: Freescale VPU video decoder imxvpu: imxvpuenc_h263: Freescale VPU h.263 video encoder imxvpu: imxvpuenc_h264: Freescale VPU h.264 video encoder imxvpu: imxvpuenc_mpeg4: Freescale VPU MPEG-4 video encod…

Hello, I am having a problem using the uart and I guess it is related with this topic. I am trying to make my Hummingboard to communicate via UART with a serial ublox GPS. I identified that the right device in armbian (5.34) is /dev/ttymxc0 since it echoes characters when I join tx/rx together. When I connect the GPS it starts sending gps data normally, but when I have to reboot the hummingboard, it does not boot. I connected a screen to the HDMI interface to see what was happening, and I get the screen message as if a key had been pressed in order to stop booting process, so the boot stops here and the hummingboard does not come up. When I disconnect …

Hello! I'm trying to boot latest releases of of Armbian (following images: Armbian_21.02.3_Cubox-i_buster_current_5.10.21.img and Armbian_21.02.3_Cubox-i_focal_current_5.10.21.img) on a Solid-Run Hummingboard2 Gate V1.4 board. (Board V1.2 freeze during Uboot) I'm getting to the "Starting kernel" message but after that things stop. Switching on the verbose output in ArmbianEnv.txt result in the output below where the kernel always stop at message: [ 0.000000] Freeing unused kernel memory: 2048K Do anyone have any thoughts/ideas here on what could possibly be the problem stopping the kernel from booting? U…

I'm running the ubuntu trusty image on a Hummingboard-i2eX and am experiencing 2+ minute boot times. The system starts booting and I get the following output before it hangs. [1.6xxxxx] imx-ipuv3 2400000.ipu: WARNING: adapt panel end blank lines [4.2xxxxx] IR keymap rc-rc6-mce not found I am assuming that it is something related to the IR keymap that is holding the system up, but am not certain. Any thoughts on getting a slightly faster boot?

I am trying to set up Armbian as an iSCSI initiator using open-iscsi. The result is Mar 15 03:07:13 matrix iscsid[2207]: iSCSI logger with pid=2208 started! Mar 15 03:07:13 matrix systemd[1]: iscsid.service: Failed to parse PID from file /run/iscsid.pid: Invalid argument Mar 15 03:07:13 matrix iscsid[2208]: iSCSI daemon with pid=2209 started! Mar 15 03:07:13 matrix iscsid[2208]: can not create NETLINK_ISCSI socket Mar 15 03:08:43 matrix systemd[1]: iscsid.service: Start operation timed out. Terminating. Mar 15 03:08:43 matrix systemd[1]: iscsid.service: Failed with result 'timeout'. with a timeout of around 90 seconds. I'm running the kernel Li…

I have a v1.2 Rockpi S with 512MB of RAM, while using the latest Armbian Focal and Buster images (20.08.1 with kernel 4.4.y), I have been experiencing WIFI issues. The device connects to the Access Point and maintains the connection but every minute or two the SSH connection hangs or freezes for several seconds and then comes back and prints everything that when on during the period it was not responsive. When I used the images with the 5.8.y kernel, I did not experience the same issue. In all cases wired ethernet (eth0) is not effected by the issue. Continuously pinging a local system shows the below result. Other WIFI devices on the same network do not experience …

Hello How to rotate screen HDMI ? 4.7.3-cubox

I downloaded Armbian for a Udoo Quad from https://dl.armbian.com/udoo/Focal_current_desktop. uname -a reports: Linux udoo 5.6.18-imx6 #20.05.4 SMP Mon Jun 15 00:30:23 CEST 2020 armv7l armv7l armv7l GNU/Linux However in https://docs.armbian.com/Hardware_Freescale-imx6/ I read: "Udoo Quad Kernel 3.14.x and 4.4.x with some hardware support, headers and some firmware included", which suggests that the image should have a 3.14 or 4.4 kernel. In /var/log/Xorg.0.log I read: [ 21.345] (II) AIGLX: Screen 0 is not DRI2 capable [ 23.279] (II) IGLX: Loaded and initialized swrast [ 23.279] (II) GLX: Initialized DRISWRAST GL provider for screen 0 LIBGL…

Hi all, After years of running Armbian on my Cubox i4 without problems, I am suddenly in a situation that I don't understand. For some reason, I decided to reboot it, and now it doesn't work anymore. Using a micro-USB cable and my Macbook, I connected to the serial line to grab some logging: U-Boot SPL 2017.11-armbian (Jan 24 2018 - 22:39:16) Trying to boot from MMC1 U-Boot 2017.11-armbian (Jan 24 2018 - 22:39:16 +0100) CPU: Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz) CPU: Extended Commercial temperature grade (-20C to 105C) at 41C Reset cause: POR Board: MX6 Cubox-i DRAM: 2 GiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using def…

Hello, I have recently tried a more recent kernel 5.10.x for my HummingBoard with imx6 solo. After playing with GPU/OpenGL acceleration I have noticed that there is no H.264/MJPEG Video acceleration present in the kernel. The video codec Chips&Media 960 driver module (kernel option VIDEO_CODA) is simply not build in. Why is that? Can it be enabled by default for future IMX6 builds? Thanks for your support!!

Foreward: Not sure if this better fits in board bring up, but I can't post there, so feel free to move if appropriate. I'm looking into the feasibility of using the Armbian build system to generate OS images for the Avnet MicroZed board. This board is based on the Xilinx Zynq 7000 platform, which is a SoC made up of a dual core 500 MHz CPU, and a Artix-7 generation FPGA. The CPU is nothing to write home about, but the FPGA opens up an interesting array of possibilities. Just in case you need an ARM board with 100+ GPIO, over two dozen serial ports, or your own function generator. Really, you're limited only by pin count, FPGA fabric usage, and what you can man…

Hi, I installed xrdp with armbian-config. Now I'm able to login with rdp client, but I'm directed to an empty desktop. No bars/menue or similar, just empty no chance of doing something useful. What's wrong? Best wishes Paul

Hello, I want to boot Hummingboard Edge with Armbian (Jessie - kernel 3.14.54) , but I'm experiencing problems during the booting procedure. Bootloader is searching for some files then it gives up. I have copied two files (imx6q-hummingboard2.dtb to imx6q-hummingboard.dtb) to /boot/dtb/ folder. It looks like it starts with the kernel, but it never loads completely. Below are the steps: U-Boot SPL 2013.10-rc4-sun7i (Oct 11 2015 - 20:45:45) Boot Device: SD1 spl: error reading image u-boot.img, err - -1 Load image from RAW... U-Boot 2013.10-rc4-sun7i (Oct 11 2015 - 20:45:45) CPU: Freescale i.MX6Q rev1.5 at 792 MHz Reset cause: POR Board: MX6-HummingBoard2 DRAM: …

[|] Error 1 occurred in main shell [ at /armbian/.tmp/work-5d76f14c-45ca-4630-ba99-8ded11db4ca4/uboot-write-Fhg7X/usr/lib/u-boot/platform_install.sh:6 and tracking down that platform_install.sh yields dd if="$SRC"/cache/sources/arm-trusted-firmware/mtksoc-20250212/build/mt7988/release/bl2.img of=$2 bs=512 seek=34 status=noxfer > /dev/null 2>&1; Note that cache/sources/arm-trusted-firmware does not appear to exist, and [although this may be my lack of knowing what to look for] I find no evidence it attempted to fetch this repo or build the firmware. Yes, this board is only recently submitted, so some problems may be expected. I did wait fo…

I've been trying to make work bluetooth in my cubox-i last months but it was not possible. I have mate desktop and I installed blueman-manager but it says 'device needs to be turned on'. I try to do it but nothing happens. I wonder if I am missing any tool or driver to make it work. By other hand I configured the swap partition and I can see the system says now I have 4.1GB as swap but also it says is using 0% any time, it doesn't matter if I have million websites opened or many applications working. So I wonder if that's normal or there is something wrong. Thanks.

Hi, Since I upgraded my kernel to version 4.19 (`linux-image-next-cubox=5.73` when I tried I think) on my cubox-i4 pro, I lost HDMI : root@cubox:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: SPDIF [Integrated SPDIF], device 0: S/PDIF PCM snd-soc-dummy-dai-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 Anyone experiencing this too ? Downgrading to `linux-image-next-cubox=5.60` solved it. apt install linux-image-next-cubox=5.60 reboot aplay -l **** List of PLAYBACK Hardware Devices **** card 0: SPDIF [Integrated SPDIF], device 0: S/PDIF PCM snd-soc-dummy-dai-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: DWHDMI […

Hi I moved from 3.14 to 4.13. In 3.14 I had a imx framebuffer , needed for my lvds LCD In the 4.13 kernel menuconfig i cannot find a way to set CONFIG_FB_IMX. How to enable this? Dig

Hi. i've compiled udoo quad image using armbian build framework. The kernel is 6.x.x. When i boot the image on sdcard, usb ports don't start: the mouse's led don't turn on and keyboard too. What can i do to solve this problem? what paramaters do i have to enable? thanks

Hello, I updated my Vanilla Jessie headless install yesterday (aptitude safe-upgrade), but the system never came back online after reboot. The screen flashes the SolidRun logo and a few lines of text, and then the LED turns off and the screen goes blank: It doesn't seem like the system boots, and it definitely doesn't connect to my home network via Ethernet. Is there a way to rescue this install? Thanks in advance, Matteo

Hello (sorry, I am writing through a translator) I have a Zyxel NAS326 with a physically damaged NAND - it does not save the device configuration. board photo: Because I do not have access to the programmer, I want to replace NAND and program it in the NAS. However, I can not run U-Boot via UART. I tried the adapters on PL2303HX and FTDI FT232RL. I'm using a kwboot on this topic: and the u-boot file from this: https://forum.doozan.com/read.php?2,27108,31893#msg-31893 Every time this error pops up: root@gutek3:/gutek/nas326# ./kwboot-x86_64 -f -t -B 115200 /dev/ttyUSB0 -b uboot.bin -s 0 -q 1 Sending boot message. Please reboot the …

Hi Igor, Thanks for your great work with Armbian. I'm currently using your Armbian4.90 for my Hummingboard Edge v2 (dual), as the newest that does not hang on PCIe initialization. Unfortunately, the OV5640 MIPI module is not compiled in this version (it is compiled in all later versions of kernel 3.14.60). Have you kept an archive all the versions of your kernel source? Is there any way to get it so we can add and compile a specific module? Of course, I would prefer if the latest 3.14 kernel could not hang with the PCIe adapter initializing, but this seems to be a pretty difficult issue... I tried the latest one available on the official Armbian site (5.00)…

Just upgraded to the new Jessie image 4.4.1. Is there any concern with this bad CRC warning? Do I need to update the u-boot.img? If so, how. U-Boot SPL 2013.10-rc4 (Feb 03 2016 - 16:37:42) Boot Device: SD1 spl: error reading image u-boot.img, err - -1 Load image from RAW... U-Boot 2013.10-rc4 (Feb 03 2016 - 16:37:42) CPU: Freescale i.MX6Q rev1.5 at 792 MHz Reset cause: POR Board: MX6-CuBox-i DRAM: 2 GiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: FEC [PRIME] Hit any key to stop autoboot: 0 mmc0 is current device ** File not found /boot.scr ** ** File not found /uEnv.txt ** ** File not …

Hi there! I recently installed Armbian (Stretch: Armbian_5.83_Nanopifire3_Debian_stretch_next_4.14.115) on my new NanoPi Fire3. I was able to boot, but it responds so slow, that it is unusable! For example, when I SSH into it, it takes a log time to show me the login prompt. When I enter the username and press enter, it takes about 5 seconds to ask me for password. When I enter password, it takes about 10 seconds to show me the Armbian banner. I wasn't even able to go past the changing of unix password on first login, because it just "froze". I have installed the image twice on my SD card, just to make sure it isn't a corrupted install.…

when i changed to run the current kernel 5.4.12 the ethernet would work ok, then while transfering over smb/samba to my windows 10 box the ethernet would totally drop, as in the light on my switch went out, not just dropping a few packets!! The only thing that fixed it was to rever "back" to 5.3.11-imx6. Note the change both up to the 5.4.12 and then back to 5.3.11 were performed via the armbian-config tool. (the system is running headless, and the log file does include a boot of "Linux version 5.3.11-imx6" as well as the working 5.3.11 Is anyone else seeing this? JB.

It was the only image I could get working. The 25.02 doesn't boot, the older versions from the archive 23.8.1 don't work either for some reason. Unfortunately I deleted the image and the rolling release moved on to 25.02.

I was trying to plug my Arduino uno into my Udoo quad but it does not appear to be assigned to a serial port, which i believe should appear as ttyACM*. when searching the kernel github page i see these relults https://github.com/patrykk/linux-udoo/search?utf8=%E2%9C%93&q=ACM. Is it possible to get these devices supported in your next kernel release?

Hey, which kernel did you use for the provided Hummingboard image (wheezy)? Is it a self-patched linux-linaro or the latest from solidrun (linux-fslc)? My test tells me, that it is the one from solidrun as I'm not able to use PCI on my HB pro. I've recognized it using the current devel of OpenELEC which also uses kernel 3.14.60 from solidrun. An older version of OpenELEC (e.g. 6.0.3) or Armbian (eg. 4.4 using 3.14.53) works quite good. The PCI driver and the dts changed quite a lot between those kernel repositories. Do you have any suggestions how to fix that? My tries all ended in a boot hang (black screen).

I have debian installed on my hummingboard pro. When I execute nand-sata-install script it looks like it works. It asks me to reboot but then issuing a df -h or mount does not show that I have a 32gb drive mounted on /. Is there something else I have to do after I run this script? Thanks! ril3y

I'm using a mpci wireless card. Previous versions of armbian detected the card without problems. Buster does not. lspci returns nothing.

Hey All, First, a big thank you to Igor and all who work hard to get armbian out to the masses Second, setting NODM_ENABLED=false NODM_USER=some_user in /etc/default/nodm as per the instructions here: http://www.armbian.com/documentation/ - section 'How to login?' doesn't seem to work for me on my cubox i4pro. I turns out that /etc/default/nodm gets overwritten with the default root values on each boot. This causes lightDM to misbehave and bugger up the Xserver. I see Xcursor drawing artefacts and the LightDM UI widgets poke through into the root autologin desktop. Even without lightDM installed and /etc/default/nodm set as follows: …

I am developing on an imx6 board that is no longer in production. It has a full Yacto-based build system that works, based on an old 3.17?) kernel, but its a pain to develop for. It's not worth spending too much time on refactoring the image, but I'm wondering how big of a job it might be to build an Armbian image for it, given that I already have a working uboot and kernel. The hardware just uses a couple of usbs and uarts, and a pcie wifi card. One wersion also has an hdmi encoder, another has hdmi display. Those might be the hardest to support, but driver support is in the kernel. Thoughts? Sent from my LM-G710 using Tapatalk

Hi, coming from "ARMBIAN 5.73 stable Ubuntu 18.04.2 LTS 4.19.20-cubox" after performing apt udate apt upgrade my cubox won't boot anymore. I've no idea how to recover from this. The output from boot is in the attached picture. What can I do?

Hello all :-) ! Not sure if I am doing something wrong at all or not. But I've been trying the wheezy image from here. While I can get everything installed ok I've a problem with video acceleration. I've managed to install the packages and have taken note of the changes here to do with installing the packages and kernel for video acceleration. But unless it is something I'm not doing right, performance dosen't exactly seem to be all that great even with acceleration. I noticed that one thing that I could do btw to improve performance just a little was to turn down the colour depth. I did this by doing the following; root@cubox-i:/boot# cat boot.cmd setenv bo…

I am using your Debian (jessie) on the new SolidRun Hummingboard-Edge board. [Linux cubox-i 3.14.14-cubox-i #8 SMP Sun Jul 12 19:03:09 CEST 2015 armv7l GNU/Linux] I am planning on using the RS-485 on the board that is tied to UART2. But I noticed that ttymxc0 (UART1) and ttymc3 (UART4) are the only tty ports that have drivers associated with them. [ "dmesg | grep tty" ] How can I turn on the driver that is associated with UART2 (ttymxc1)? Thanks,

Hi, I installed latest Jessie desktop version on Cubox i4Pro but audio via HDMI still does not work... Any solution? Thanks

Hi, If you think that Solid-run Cubox-i kernel branch is becoming outdated, you can use a mainline linux kernel with the following enablement patches: Russell King home dir: http://www.home.arm.linux.org.uk/~rmk/cubox/?C=M;O=D Grab the most recent hummingboard-cubox-i DIFF big patch and patch it into your vanilla 4.1 kernel source dir. Then use a default config appropiate for a Cubox-i / Hummingboard: # make imx_v6_v7_defconfig hope it helps

I've got a CuBox i4P with an external SSD connected via eSata and has an external power supply. The 960GB SSD isn't recognised on the system: df -aTh Filesystem Type Size Used Avail Use% Mounted on sysfs sysfs 0 0 0 - /sys proc proc 0 0 0 - /proc udev devtmpfs 869M 0 869M 0% /dev devpts devpts 0 0 0 - /dev/pts tmpfs tmpfs 202M 8.1M 194M 5% /run /dev/mmcblk1p1 ext4 15G 1.2G 14G 8% / securityfs securityfs 0 0 0 - /sys/kernel/security selinuxfs selinuxfs 0 0 0 - /sys/fs/seli…

I was trying to install the udoo kernel but got stuck with this error: root@udoo:/tmp/4.0.8# ls -la total 32968 drwxr-xr-x 2 root root 4096 Jul 29 14:21 . drwxrwxrwx 5 root root 4096 Jul 29 14:21 .. -rw-r--r-- 1 root root 16875520 Jul 13 11:30 4.0.8-udoo-next.tar -rw-r--r-- 1 root root 11204 Jul 13 11:30 linux-dtb-4.0.8-udoo_1.8_armhf.db -rw-r--r-- 1 root root 49792 Jul 13 11:30 linux-firmware-image-4.0.8-udoo_b -rw-r--r-- 1 root root 6844194 Jul 13 11:30 linux-headers-4.0.8-udoo_1.8_armb -rw-r--r-- 1 root root 9096354 Jul 13 11:30 linux-image-4.0.8-udoo_1.8_armhfb -rw-r--r-- 1 root root 769836 Jul 13 11:30 linux-libc-dev_1.8_armhf.deb -rw…

A couple years back a company named TBS, mostly known for their DTV hardware, released a mini PC styled thing. It's called the TBS2910 Matrix and was marketed mostly as a Kodi box. Sadly it doesn't seem the product made the sales necessary to keep the company interested - which in my view is a shame since it's got some interesting hardware features: Quad-core i.MX6 CPU (1GHz) 2GB DDR3 Ram MiniPCIe slot 16GB eMMC Storage SATA connector with 12V power, capable of powering a 3.5" HDD On-board 2.4GHz Wifi Gigabit ethernet (likely limited to 400Mbps or so) 3 USB 2.0 ports + 1 mini USB otg port 1 full-size SD slot, 1 microSD slot HDMI, analog and optical audio out I…

@Igor how come there isn't any mainline kernels available for these boards lack of time or lack of interest ? currently using xilka kernel but would love to have it in apt less messy would be awesome to include/combine those builds and get more support for imx6 since graphics is up to 3.14.60 and mainline is at 4.4.0 (minimal support for graphics kinda like your mainline packages).

I have lots of HummingBoards 2 Edge with eMMC but now got a batch with the new SOM 1.5 and eMMC the original u-boot from next and stable branch (2013-10rc4) get stuck on SPL from time to time on the new SOMs so I'm trying the dev branch which has this new patch: https://github.com/armbian/build/blob/master/patch/u-boot/u-boot-cubox-next/U-Boot-mx6cuboxi-add-support-for-detecting-Revision-1.5-SoMs.patch Copying SPL and u-boot.img to eMMC and booting produce the following: U-Boot SPL 2018.03-armbian (Jun 07 2018 - 16:06:14 -0400) Trying to boot from MMC1 Card did not respond to voltage select! spl: mmc init failed with error: -95 SPL: fail…

Hello could someone point me in the direction of the stretch images if they are still hosted here of course. I want to run omv and i just found out what is happening with omv5 and armbian the past year. So ill go stretch and omv4. Kind regards Oliver

I upgrade Jessie to Stretch and installed (from armbian stretch) linux-image-dev-udoo linux-headers-dev-udoo linux-dtb-dev-udoo linux-u-boot-udoo-dev Unfortunately the kernel is not booting any more from sata: U-Boot SPL 2015.10-armbian (Nov 22 2017 - 17:21:35) U-Boot 2015.10-armbian (Nov 22 2017 - 17:21:35 +0100) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Board: UDOO Quad DRAM: 1 GiB MMC: FSL_SDHC: 0 No panel detected: default to HDMI Display: HDMI (1280x720) In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME] Hit any key to stop autoboot: 0 ** Bad device size - sata 0 ** AHCI 0001…

Hi all, sorry if my question is stupid but I would like to use ARMBian on this Keith & Koep board. I know that there are different problems with serial configuration and that may prevent u-boot to start. I would like to know if I can regenerate easily an ISO adaptating the hardware with custom device tree .... Which repositories should I clone ? Thanks for your support Kind regards Jerome

On my Cubox, can I upgrade Armbian Bionic to Cosmic? Is that going to work? I'm not using any GUI / HDMI stuff, so that is not relevant for me Reason of my question: I want OpenSSL 1.1.1 (with TLS1.3), which is a part of Cosmic (and not of Bionic).