Beginners

Hi, I need set the PC1 pin as output on a device driver using the new gpiod_export() method. What argument should i pass on the gpiod_get function? struct gpio_desc *gpio; gpio = gpiod_get(NULL, "PC1", GPIOD_OUT_HIGH); if (IS_ERR(gpio)) { printk("Failed to get GPIO: \n"); return PTR_ERR(gpio); } // Export the GPIO ret = gpiod_export(gpio, false); if (ret) { pr_err("Failed to export GPIO: %d\n", ret); return ret; } // Set the direction of the GPIO ret = gpiod_direction_output(gpio, 1); if (ret) { pr_err("Failed to set GPIO direction: %d\n", ret); retur…

I'm looking for help getting cec working on a Le Potato. i3Desktop image from this page - https://www.armbian.com/lepotato/. I’m getting the following error with cec-ctl: Failed to open /dev/cec0: No such file or directory

Hi, I just start using armbain after login I saw this error date: invalid date '</body>\r' per attach image. What cause this error ? I have look into motd configuration this error not coming from there. Another monitor package that was installed is rpimonitor. It's look like a some kind of script that run after login.

Hello all, Orange Pi 5b v1.1 16GB/256GB # Wi-Fi 6 and WPA3 are not available options in current Debian Cinnamon release. # OP 5b does have these features so comparability isn't an issue. # Works fine with Orange Pi images. # All steps given on download page were taken. Help would be greatly appreciated. Thanks.

Hello, I'm trying to use pin PC3 as an interrupt, but it returns the error code -22 in the gpio_to_irq() function. In user-space i can use it normally as a GPIO, but I need it to function as an interrupt in a driver. Board: Orange Pi One, Armbian 23.8.0 #define GPIO_PIN 67 #define GPIO_PIN_DESC "GPIO PC3" static int __init mytapp_controller_proc_init(void) { int ret,gpio_irq; uint8_t idx = 0; printk("mytapp_controller_proc_init 444%d\n",GPIO_PIN); msg = kmalloc(PROCFS_MAX_SIZE, GFP_KERNEL); if(!msg){ printk(KERN_ALERT "Error: kmalloc error\n"); return -ENOMEM; } if (gpio_request(GPIO_PIN, GPIO_PIN_DESC)) { printk("GPIO re…

Hello. I've searched here, the Libre computer forums, even tried "cheating" with asking chatgpt. Using a "Le Potato" AML-S905X-CC with Armbian Jammy 22.04.2 LTS. I've gotten far enough to be able to read the switch on the GPIO with pulled to 0 reading as 1. button untouched: ~$ sudo gpioget --active-low gpiochip1 97 0 button pressed: :~$ sudo gpioget --active-low gpiochip1 97 1 From here though, I can't seem to figure out what to do next. I've seen suggestions to use a python script with a sleep to using device overlays. The device overlay examples I see using armbian are typically for orange Pis and I can't seem to extrapolate to the le potato g…

Hello all, I hope this finds everyone well. This is my first post and I’m not sure where to put it so, as per forum instructions, I’m dropping this here. After the last update released on July 6th, 2023 that fixed a Wi-Fi and Bluetooth issue (thank you), another issue developed. The calendar displays words and letters in a language that I’m not familiar with. It appears to be beautiful looking symbols, but unfortunately, they are meaningless to me. I have attempted to correct this in every way I know but with no luck. The date and time format will change but the language will not. This hasn’t happened with the previous versions. I’m in th…

I used to be able to easily install ili9341 lcd's on old armbian using, but now it looks like it became much harder now... can you tell me or point me to the right direction to start?

Hello, I'm in the process of setting up OrangePi PC Plus and when updating packages I get this error Hit:1 http://ports.ubuntu.com jammy InRelease Get:2 http://ports.ubuntu.com jammy-security InRelease [110 kB] Hit:4 http://packages.microsoft.com/repos/code stable InRelease Get:5 http://ports.ubuntu.com jammy-updates InRelease [119 kB] Hit:7 http://ports.ubuntu.com jammy-backports InRelease Hit:3 https://cli.github.com/packages stable InRelease Get:6 http://armbian.hosthatch.com/apt jammy InRelease [52.4 kB] Err:6 http://armbian.hosthatch.com/apt jammy InRelease…

I am running Armbian 23.05.01 bookworm, release 12, on a Libre Renegade (ROC-RK3329-CC) I installed RDP from Armbian config. Seems to have installed. I've shutdown, restarted several times. First I get a black screen on my Windows PC Then the screen turns turq and I see this error: When I click the OK I see this dialog: I've tried every one of those options and none work. I've tried them from my created user and also with root - no joy. I get an error like this: I posted here, not knowing exactly where to start. Dan Reynolds

If I am using SSH over a WIFI connection and then plug in the ethernet cable, then I lose my SSH connection. Simply disconnecting the cable doesn't resolve the issue; I need to reboot without the ethernet cable connected to reestablish the SSH over WIFI. The system diagnosis is here.

I am using Armbian 23.5 Jammy XFCE on a Tinker Board 2S. I have a number of issues to sort, one of them being display. The display is receiving a 16:9 signal, but the right hand side of the screen is covered by a black-white-green pattern under which I can move windows (image attached). How can I change the settings to avoid this?

How to adjust the resolution of the armbian so that the display would fit I'm using a 3.2" ILI9341 TFT LCD I also followed this tutorial https://mobile4dev.blogspot.com/2017/09/orange-pi-pc-tft-ili9341.html

Would like to build something like a NAS, because I'm tired of connecting an external drive via USB. I am thinking to use bananapi M2 berry for this. I would power the 3.5 HDD externally and don't care too much about SATA speed. However, it is important to me that armbian works without manual adjustments, because it wouldn't cope with them. Should I go ahead with the experiment?

Im trying to play video on CLI interface. Banana pi M1 im using.I installed VLC, MPV, mplayer but not successful. please help. my video is in pendrive.

Hi, I need to help for understandable how set right clock hierarchy for i2s bus with external master-clock signal. This mode supported rockchip processors (RK3328, RK3399) but there are very small information how it can do. Today we have out of box in armbian for Nanopi Neo3 working I2S with master-clock from PLL, but I want change master-clock source from PLL to external signal. In souce and clock debugfs I find that I2S1 ("i2s1_pre") can be clocked from 4 sources: clk_i2s1_div, clk_i2s1_frac, clkin_i2s1, xin12m. By default parent for i2s1_pre set to clk_i2s1_div, which have parent cpll. Hence we must change parent for i2s1_pre to clkin_i2s1, but clock clki…

Armbian 23.5 Ubuntu Not sure what I touched but my OpenGL has reverted from the Mali-G52 hardware accelerated renderer back to the llvmpipe. How can I changed this?

I'm running Chromium in kiosk mode in armbian using the following command: chromium 'http://localhost/' --window-position=0,0 --start-fullscreen --kiosk --noerrdialogs --disable-translate --no-first-run --fast --fast-start --disable-infobars --disable-features=TranslateUI --disk-cache-dir=/var/www/ --disable-pinch --overscroll-history-navigation=0 --disable-features=TouchpadOverscrollHistoryNavigation --enable-logging --v=1 --window-size=1366,768 However, I'm experiencing a blank page transition issue when navigating from one page to another (for example, from page 1 to page 2). I have tried using other browsers, and the issue doesn't occur. Additionally,…

I am using armbian on banana pi m2 zero with screen 1920x360. For some reason display controller didn't tell edid, so banana using default value and it doesn't look right (only a few more than half of the screen displaying anything). I want to use this screen, so I want to override default values. How this can be done? I tried setenv video-mode sunxi:1920x360-24@60,monitor=hdmi saveenv but this didn't work (saveenv tells `Saving Environment to FAT... Unable to use mmc 0:1...`) and before booting u-boot tells `Loading Environment from FAT... Unable to use mmc 0:1...` I am using armbian jammy (Armbian_23.02.0-trunk_Bananapim2zero_jammy_current_5.15.80_x…

I just wrote the Armbian Ubuntu Jammy Desktop image to an SD HC card and booted up fine with it (although I can only boot if I disconnect the HDMI cable -- when boot up is finished, I can plug it in and use the desktop. That's another story, but I have the same issue with official NanoPi Ubuntu images. Next, I transferred the Armbian OS to the eMMC and indicated that I wanted both the boot and system to be on the eMMC. After transferring the rootfs and getting the Power Off prompt, I powered off, then removed the SD HC card, then attempted to boot. However, when I tried to power on again, the NanoPi went into a reboot loop. Armbian will not boot without t…

I have multiple n2s and I don't want them all to be called odroidn2. What is the recommended way to change the hostname of an armbian system?

Hello, I would like the ability to run Firefox or Chromuim rather than Gnome or any desktop environment when I start up my Orange Pi 5. This is for a device I'm setting up that (when rebooted) ideally won't even prompt the user to log in, it'll just directly bring up the browser and directly to a specific URL. Any thoughts on how I might do this? David

Hi, i have installed the latest Armbian 23.5 Jammy on my opi+2e and since then, only the top left of the screen is showing text, like if the screen is divided in 4 and only the upper left is showing login screen and text. If I try to install a desktop environment, everything goes full screen, but I see the mouse cursor of login screen overlapped to desktop, so i have two mouse cursors: one fixed and the other that can be moved. WTF is going on? Why don't you test the images before you publish?

On X86 and AMD64 systems they all have either the UEFI bios or the old bios. I don't know what the Raspberry Pi uses but I don't think it's UEFI. Do any of the ARM systems use UEFI? How does Armbian boot on the non-UEFI systems?

Hello Everyone: I am trying to install ARMBIAN on Orange Pi5B's EMMC,but ARMBIAN could not recognize it. According to this article,it should be caused by something wrong in dtb file. Could I fix it by armbian-config's dtc editor?? Thanks anyway!!

Hi all. I have a Rockpro64 with u-boot flashed to SPI, and Armbian installed to NVMe drive*. When I use the HDMI port on the Rock to a standard HDMI port on a monitor, everything displays without issue. But recently I tried connecting to a Viewsonic va1655 using the HDMI to mini-HDMI cable, and the monitor displays fine while U-boot is doing its thing. But right before Armbian loads, the Viewsonic monitor flashes yellowish orange and then completely loses the signal. Buuut if I unplug the VS monitor and plug in the other HDMI monitor to the rock, the image is restored and Mr. Tux is patiently waiting for me to enter my password. *I'm not sure if this matters, but I u…

Hi guys, which is the Armbian recommended way to jump to a newer Userspace version? A fresh install ? A regular system upgrade ? Thanks in advance, 🙏 F.

So I had my OPi Zero 2 running Sonarr and Emby with a mounted shared folder, I have a HDD connected to a USB3.0 router with trasmission on it working great, but all of a sudden 3 days ago it didn't boot, don't know why, yesterday installed bookworm on another sd card, trying to mount my shared folder is giving me the error mentioned on title: dolphinus@orangepizero2:~$ dolphinus@orangepizero2:~$ sudo mount -t cifs //192.168.2.2/Descargas /home/dolphinus/Descargas Password for root@//192.168.2.2/Descargas: mount error(22): Invalid argument Refer to the mount.cifs(8) manual page (e.g. man mount.cifs) and kernel log messages (dmesg) It asks me for a passw…

I have a usb sound card on my sbc. Im only getting left channel audio. Ive tried a different usb sound card and different cable with no luck. I run the command below with no luck, only get audio through the left speaker. speaker-test -t wav -c 2 Any ideas how to fix this?

I'm using the Odroid N2/N2+ 23.5 Jammy minimal image. I then updated and upgraded successfully. I then attempted to install MATE via tasksel (which I installed) but that immediate fails with an apt package missing error. SO then I tried to install MATE manually by: $ sudo apt install mate-desktop-environment mate-desktop-environement-extras $ reboot There didn't seem to be any display manger installed so I stalled lighdm $ sudo apt install lightdm lighdm-gtk-greeter $ reboot Then I noticed that Xserver was not installed (really, that's no a MATE dependency!!!) $ sudo aqt install xserver-xorg …

Hello, I just bought Orange Pi PC lite and I have a problem with the version of Orange Pi on site is I think a Server Desktop and Doest have Gui Interface where can I Download the Graphical Interface, I think It is possible but I dont know where to get it , If someone Help me I aprricate it.

So, as the title describes, I flashed Armbian Jammy Minimal CLI to a micro SD card and booted my lepotato, and was able to setup a user and update it via apt, set a static IP, but armbian-config is not an available command. I have a armbianmonitor log uploaded here: https://paste.armbian.com/berejipusu When I try to run armbian-config, well, which doesn't work, and autocomplete for "armbain" gives me these options: armbian-add-overlay armbian-install armbianmonitor Any help would be appreciated. Thank you.

Hi, No matter if I run the "sudo reboot" command or use the restart option from Gnome desktop, the Orange Pi 5 is not rebooting. It runs a splash screen with some kind of information after I execute that action, but after that the splash freezes and nothing happens. So I need to manually power off and then power on the Orange Pi 5 board. I'm using the following setup: Armbian 23.05.1 Thanks!

I've installed the latest Armbian Bookworm Cinnamon desktop image to the EMMC of the Banana Pi M5, but it does not display anything on the HDMI output after startup. Here's what happens when I start the system: - Starts loading the kernel (I can see the startup messages) - Shows the "Armbian" loading screen (with the spinning icon) - Switches back to the startup messages for a bit - Shows a black screen with a single "_" in the top left corner - After a few seconds my screen says that there is "No Signal" The Banana Pi still seems to be running, I can see the lights. Any idea what happens and how to fix it? …

Recently I installed ubuntu-desktop and switched to gdm3. This caused a lot of my shortcut names and file names to become a large amount of gibberish, so I uninstalled and switched back to lightdm. I still do not have a lot of my icons: and now armbian-config does not open through the shortcut: I can still open it with the terminal but this makes me think there are bigger issues.

I know I'm trying to be lazy but why can't we install the PREEMPT_RT kernel from the Debian Bookworm Repositories? eg with: sudo apt install linux-image-rt-arm64. This appears to work but it does not boot into the new RT kernel. Downloaded the deb file and used sudo dpkg-i and it also failed to boot yet this command works if we install a RT kernel we built in the build environment Ran armbian-config and tried to install the kernel but alas its not displayed in the list. Why not? I can pull down Debian Bookworm for the Raspberry Pi from the Debian site and install preempt_rt this way. Why does Armbian make it so hard? …

Ramlog.service postrotate will execute a cat from /var/log.hdd directory to /var/log directory while rsyslog.service is always outputting stuffs in the background to /var/log directory. This in general has no problem except for some files which are mostly preoccupied with output from rsyslog during logrotate activation, namely syslog and a varieties of journals entries. I have found some of these postrotate failures with cryptic messages as write errors from cat and corresponding rsyslogd omfile module stating lost messages. I suspect two independent processes competing to send output to same files hence causing these errors. I don't know enough of detail but I think ther…

Hi. I have my orange PI OPT 3 LTS running Ubuntu.. The system is installed in /dev/mmcblk0 (I believe that's the SD card?), and I just checked with gparted that it still has the Android it came with on /dev/mmcblk2 (I believe that's the internal memory?) Anyway, I would like to move Ubuntu to the external USB HDD I added. I created a /dev/sdb2 for it in ext4. I launched nand-sata-install a few times, but I'm afraid of picking the wrong options.. Which options should I pick to ensure that it does not destroy my Ubuntu installation in the process? Many thanks, -t

Im stubmeld accros armbian while search for a ARM distribution for my RockPi S. I started successful with writing it to a SD Card and run it from there. Now i want to write it to the internal storage and start it from there. So far so got, everything "worked". But it stucks in a boot loop. I attached a Serial/TTL to USB converter and noticed the same output over and over again. Willkommen zu minicom 2.7.1 Optionen: I18n Übersetzt am Aug 13 2017, 15:25:34. Port /dev/ttyUSB0, 15:37:49 Drücken Sie CTRL-A Z für Hilfe zu speziellen Tasten DDR Version V2.06 20211109 CHIP ID = 0x00003308 REG2C: 0x00000033, 0x00000034 In 589MHz DDR3 Col…

Seems like a reboot fixed the issue. the only other thing I did was to start alsamixer and made sure the line out was not muted. I setup Jammy 22.04 on an OrangePi PC + and trying to get sound to work with XFCE through the speaker jack. I get sound output through the speaker jack if I log in via the terminal and use speaker-test -t wav -c 2, but I get no sound in XFCE through the speaker jack. HDMI works. What am I missing.. root@orangepipcplus:/etc# uname -r 5.15.93-sunxi root@orangepipcplus:/etc# lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 22.04.2 LTS Release: 22.04 C…

Hi, My Nanopi M4V2 runs perfectly on Buster. The Nanopi runs stable and I don't have any issues for my use-case. It runs 24/7 and is only accessible through Wireguard. On the website from Debian it says that there are no security updates anymore for Buster. Does this also apply to the Armbian version? Of could I just keep running Buster if I keep kernel and software up-to-date? https://www.debian.org/releases/buster/ Thanks for the help, Lennyz

Greetings! I am trying to enable auto login feature via armbian-config. After I try to go to system > desktop and stop the DM service, it just go to blackscreen with the white cursor blinking on top. I cannot do anything except ctrl+alt+del which reboots the system back to the destop. Is there another way to set the auto login? Am I missing something? I am using Rock 5B board. Thank you for your help!

I reinstalled my OrangePi5 with a newly built debian12 based image and in the middle of setting up the third one I lost SSH connection. Now I have 2 OPi5 with the Armbian MOTD and whatever unseen setup that occurs behind the scenes and a third one where I manually configured locales and tzdata. Is there a way to re-run that first login script manually? Thanks

I've set up 23.02 Debian Bullseye CLI on my Orange Pi 5. I believe I read 23.05 is coming out soon. Would I just do an apt update and then apt upgrade to make the change? I'm at the point where I could just re-install and start with 23.05 but what would I do in the future for new updates? Thanks.

NanoPC-T4 only has 16GRAM, which is still a bit small for daily use. So I want to put u-boot on emmc or sd card, and install the system on nvme solid state drive. If I want to realize this function, can the armbian-config tool help me realize it quickly? Or do I need to set u-boot parameters and compile by myself, thus installing the system in nvme SSD?

Due to systemd, Journal is going to replace all journals sooner or later, it's already one of the busiest journaling on the sytem. The logs are binary and can't be rotated like text logs, they are already compressed and can't be read by text editor, instead only by journalctl. Thus, in /usr/lib/armbian/armbian-ramlog , the directory /var/log/journal is excluded from standard log rotation and copying to HDD. Instead, it is copied once to /var/log.hdd/journal and a soft-link is created: /var/log/journal pointing to -> /var/log.hdd/journal . The RAM logging was introduced to spare the SD card, preventing many write actions that wear the SD card qui…

Is there any support for Rock 3 C (RK3566)? I've tried booting from the Rock 3 A image, but no joy. It looks like the Rock 3A was RK3568 so I wonder if using another device tree overlay for RK3566 might otherwise work?

Hi everyone! I've just got a new odroid c4 and am trying to hook it up to a small i2c oled display. I've wired it up to the I2C A SCA and SCL pins with 3.3V and GND as needed, and enabled both I2C A and B in armbian-config. However, when I run i2cdetect -y 0 I get the device grid with a 30 in position 30 and nothing else, both with the display hooked up or not, nothing changes. Is there anything obvious I might have missed to get I2C running? Thanks in advance for your help!

Tested with speakers and headphones, now working right channel in 3.5 mm. Speakers and headphones works correctly with another devics. Tested on official builds(firstly), pulseaudio, pipewire+wireplumber, also tested self-builded via official building script with same drivers. Speaker-test detects only front left channel. What it may be? How I can fix that? Thanks in advance.

Hi All, I have a BPI-M2 ZERO, BANANA-PI-ZERO with SERIAL to USB plugged in. It's being detected by lsusb Bus 002 Device 005: ID 1a86:7523 QinHeng Electronics CH340 serial converter but it doesn't appear under /dev/ttyUSB0 The problem is that I can't see it under /dev/ as /dev/ttyUSB0. I haven't tried installing CH340 drivers yet. Should I use the ones for Ubuntu? Here is the tutorial I found but I'm not sure if those are the correct drivers: https://learn.sparkfun.com/tutorials/how-to-install-ch340-drivers/all uname -a Linux bananapim2zero 6.2.13-sunxi #1 SMP Wed Apr 26 12:30:09 UTC 2023 armv7l GNU/Li…

Hey guys, brand new to linux so sorry for obvious/easy question being obvious/easy I wanted to set up Pi Hole on my new Renegade, but I cannot figure out how to make/find a static ip address. I have found the IPv4 settings, tried to create an ip address in there, but I don't think it worked. Thanks for any help or advice you can give me, after I get the static IP address set hopefully I won't have any more problems setting up Pi Hole. Thanks again!

I built armbian from the main branch for my tablet based on Allwinner A33 and the topic: Used q88_a33_tablet_1024x600_defconfig and tried q8_a33_tablet_1024x600_defconfig the image was built successfully, at startup I see the console of u-boot, and can use it bu OTG, but only before message the kernel starting... and then after kernel starting it will a black screen as i think the video mode or something else is configured incorrectly, I checked the boot kernel logs, the kernel starts successfully, there are no any errors during start, apparently the problem is only in the video output on my tablet. I ask for help, help me understand what th…

Dear All, I got a zfs upgrade today, I updated the packages but then it failed to build the module, thus I tried to update kernel and firmware but it failed the same: hecking whether CONFIG_MODULES is defined... no configure: error: *** This kernel does not include the required loadable module *** support! *** *** To build OpenZFS as a loadable Linux kernel module *** enable loadable module support by setting *** `CONFIG_MODULES=y` in the kernel configuration and run *** `make modules_prepare` in the Linux source tree. *** *** If you don't intend to enable loadable kernel module *** support, please compile OpenZFS as a Lin…

Hi, trying to nut out the problem of being unable to restart after installation of the OMV Wireguard plugin. I have removed the wireguard-tools package and installed the 4 rockchip64 edge 6.1.11 packages. It took me a while to realise that armbian-config was not installing the headers when selected but wondering if there's a necessary order for installation ie linux-source-6.1.11-edge-rockchip64 first maybe? Sorry I realise how tedious it is supporting folks who are feeling around in the dark but I've wasted so many hours starting from scratch I either have to give up or ask for a tip. TIA

Hello, Is it possible to set the speed of the UART3 to 921600 baud instead of 115000? How to do it? I need to connect to an arduino at that speed. I have tried with minicom but I can't get it. I have also tried to put the following command dtoverlay=miniuart-bt in /boot/armbianEnv.tx but it doesn't work either. to 115000 if I can connect well, therefore the port works correctly Is there any way?

Hello, BPi M5 freezes after a couple of hours running randomly. - use armbian Armbian 23.02 Bullseye ( 6.1.11) - same effects with Armbian Bookworm CLI kernels 6.1.x 6.2.x Now tried Sinovip Ubuntu (kernel 4.9.x ) aud it is running for days ! form their Homepage armbian from Sinovip page link also freezes... Why Armbian ( or Kernel 6.x ?) freezing . also found that USB power (for my data-USB-HDD) will be switched OFF during boot mostly . tried uhiubctl with permanant switch ON .. -> starts better - can ust USB-HDD in fstab ... but System freezes (include: USB no longer with power ) Is the…

I have an orangepi pc and am trying to use a 3.5 inch TFT-LCD using fbtft. I was told to use armbian 20.05.4_Orangepipc_focal_current_5.4.45 in this case. I am trying to find version 5.4.45. But it hasn't worked out yet. The oldest in the archive is version 5.10. May I know how to find the 5.4.45 version? Please tell us

Hello I use a odroid c2 und create a full img backup. Can i use this in a newer odroid like too? I have some programms etc on it and don't want to reinstall it.

I'd like to run usbdux usb hardware with armbian but have no experience so far in building modules. I compiled the current armbian branch form github. But I could not figure out how to compile the comedi drivers and include it in the kernel. help appreciated Thomas

I'm installed Armbian_23.02.2_Orangepi5_jammy_legacy_5.10.110_xfce_desktop to Orange Pi5. I have attached external RTC module with DS3231 on I2C5 (/dev/i2c-5) and try it. https://forum.armbian.com/topic/7349-rtc-ds3231-how-to-install-tinker-board-stretch-414/#comment-56094 (Instead of I2C-0, it was I2C-5.) However, the DS3231 does not recognize it. I type i2cdetect -y 5, it remains at 68 without becoming a UU. Is there any solution?

I tried setting SKIP_BOOTSPLASH=yes from Hidden options for advanced users of the Build Options page, but the Armbian splash screen still appears. Since I have to ask here, I am obviously not an advanced user. 🙃 How do I eliminate the boot splash screen as I am building/testing images? ./compile.sh \ BOARD=visionfive2 \ BRANCH=edge \ RELEASE=lunar \ BUILD_MINIMAL=no \ BUILD_DESKTOP=no \ KERNEL_CONFIGURE=no \ SKIP_BOOTSPLASH=yes \ CARD_DEVICE="/dev/sdb"

Опубликовано: только что · Hidden - This content must be approved before it can be edited. HOT NEWS!!! With Armbian Armbian 23.02.2 Jammy with Linux 5.15.93-rockchip64 on (rockpi-4b plus v.1.72) Add (do it elso on all booting fevices = MMC, NVME, MPD, SD) the following lines to /boot/armbianEnv.txt overlays=spi-jedec-nor param_spinor_spi_bus=1 Reboot If you shorted 23-25 pins in 1.) then: disconnect them after the ROCK Pi 4 fully boot's enable spi-nor by executing (as root): echo spi1.0 > /sys/bus/spi/drivers/spi-nor/bind verify that the SPI mtd interface is enabled by running ls /dev/mtdblock0 if the last comman…

Is there any support for this platform. https://wiki.seeedstudio.com/Quantum-Mini-Linux-Development-Kit/ Devicetree https://github.com/coolflyreg/quark-n If not. Where can I see how to add a new platform. If template or tutorial. Original system is Ubuntu 18 and very old kernel. I like Debian better.

Hi peoples, updating my old NAS (odroidH1 OMV) 1TB SSD New set-up: BPiM5 armbian bullseye - OMV samsung 2TB SSD installation up and running but... OMV or sudo fdisk -l cannot see new Samsung 2TB SSD (I have 2 of these, one will be back-up) I have connected ssd's via sata usb3.1 cable

Hallo my odroid C2 shutdown during the night. i can see it always on the next day, when the ssl connection is disconnected. Is there any log file, where i can see, if there was any problem? thank you

I picked up an OrangePi PC Plus. I installed armbian Jammy which does not have the mt7921u driver. I would like to install the driver and was wondering the proper steps. I have done apt install linux-headers-current-sunxi cd /usr/src/linux-headers-5.15.93-sunxi make scripts Now is it a matter of grabbing the mn7921u source and compiling it? Thanks for any direction.

I run "armbianmonitor -u" and I got this : https://paste.armbian.com/bapohonaja My SBC is orangepi zero 2, and I tried to use it as a NAS. But sometime the system hangup because I push to much file in my usb-disk. And I G**gle about it. Somebody said because usb driver is "UAS". So I use command "lsusb -t" and bingo, my usb driver is "uas": ``` >: lsusb Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1…

Hi, I have Armbian 23.05.0-trunk Bullseye with Linux 5.4.239-odroidxu4 on my XU4. I recently bought a USB Bluetooth adapter using RTL8761A. But the firmware is not present in rtl_bt. I want the Bluetooth adapter to work for Home Assistant. I am quite new to this stuff, so if you need any additional information i will provide. Thanks in Advance.

My dotnet apps not work in new armbians(libssl error). How downgrade openssl 3.0 downto openssl1.1.1?

Hello Armbian community I just acquired a Raxda Rock 3A with a Raxda Wireless module A8 (RTL8852BE) card. The Ubuntu distribution from Raxda seems to work pretty well, but it's not very recent, which is why I wanted to try Armbian! The current version (Armbian 23.02 Jammy Kernel 6.1.y, Size: 579Mb, Release date: Feb 27, 2023) seems to work, but I have two questions: 1) No wifi, the card is not detected (probably a driver issue, it works with the official OS), if there are members who have solved this? 2) I haven't seen much information on setting up a boot from an nvme storage, have you tried this? Have a g…

Hello everyone! I'm new here, and I want to ask about my Orange Pi One. (I have posted this on different platforms also but I don't have any answers yet.. And someone recommended this community..) The problem here is I have a GC2035 camera module that I inserted behind my Orange Pi one, I tried running "ls /dev/video*" to check if it can recognize my cam, and it can recognize it, the result is "/dev/video0" Now when i tried to run "fswebcam test.jpg", there was an error, the error was: No input was specified, using first. Unable to query input 0 VIDIOC_ENUMINPUT: Inappropriate ioctl for device So that's why i tried…

Hello- Just got my EspressoBin v7, trying to boot to SD using Armbian 23.02 Bullseye. Followed instructions at https://www.armbian.com/espressobin/. Board is 2GB, so I used flash-image-DDR4-2g_2cs_6-1200_750.bin. U-Boot showed CPU runs at 1200, and I confirmed "C120" on the chip. Interrupt boot process bubt flash-image-DDR4-2g_2cs_6-1200_750.bin spi usb env default -a saveenv Flashed Armbian_23.02.2_Espressobin_bullseye_current_5.15.93_minimal.img to a new SanDisk SD card with belenaEtcher and dd. Board doesn't boot, I get "Wrong image format for "source" command" then it tries to boot other device…

I cant use the number keys on my keyboard to type in 1234 as the manual says. I can only type in "root" at the login but I cant type anything in the password section.

Hi There, Details: Linux orangepi4-lts 5.15.93-rockchip64 #23.02.2 SMP PREEMPT Fri Feb 17 23:48:36 UTC 2023 aarch64 aarch64 aarch64 GNU/Linux I got issues from the Armbian when with Opi 4 LTS. 1.USB 3.0 or USB C not working with the kernel with WD Blue SN570 1TB (1.00)SSD failed in OPI 4 LTS. only works when i connect in USB 2.0. HW is OK, but suspecting problem with drivers (kernel). Tried below options: 1. Tried different cable but no luck in USb 3.0 port or USB c type. 2. same cable works fine in Windows and USB 2.0 3. Only not working detected in USB 3.0 port hub. Attached screenshot. Tried various troubl…

Hi there, I am facing issue with "apt update / apt upgrade" that I don't understand (bold big font below "code"): root@orangepi4:/var/spool/cron/crontabs# export LC_ALL=en_US;apt upgrade bash: uwaga: setlocale: LC_ALL: nie można zmienić lokalizacji (en_US): Nie ma takiego pliku ani katalogu Reading package lists... Done Building dependency tree Reading state information... Done Calculating upgrade... Done The following packages were automatically installed and are no longer required: bsdmainutils gir1.2-gst-plugins-base-1.0 libbind9-161 libdns1104 libdns1110 libdrm-dev libdrm-freedreno1 libdrm-tegra0 libf2fs-format4 libf2fs5 libglvnd-core-dev lib…

Hello I want to get cpu and ram infos via bash command. So i use this for temperature: For the cpu usage i needed a long time to find a solution. now i found this: echo $[100-$(vmstat 1 2|tail -1|awk '{print $15}')] For the free ram usage, i will use free --mega My question Are this command correct? the cpu command line is really new for me... does it takes a lot of ressources, if i use this commands every 2 seconds to get a real time listening? i need to write it in a database to get a graphical solution. Thank you for your help

Hey Gang, I'm a very novice linux user, just know enough to get around and follow instructions for the most part. I recently started getting the following error when trying to ssh to my armbian box from an up to date macbook. Unable to negotiate with <ip address> port 22: no matching host key type found. Their offer: rsa-sha2-512,rsa-sha2-256,ecdsa-sha2-nistp256,ssh-ed25519 I've read online that you can get around this with "-oHostKeyAlgorithms=+ssh-dss" temporarily, but I cant seem to find a guide on how to regenerate the host keys on armbian to match more current standards (or what I assume is ssh's up to date minimum) Doe…

Hi Guys, I'm new on Armbian but not on Linux in general. I was pleased to see an up-to-date armbian release for my nanopi-r4s with a kernel greater than 6.x ! 🤗 For my first day, it's pretty good and I can find most of the things I was looking for (even ripgrep). But, I have a look at the services and I've found that haveged is still set. For what I know, since 5.18 version, "Linus" changed his mind for entropy (see https://www.phoronix.com/news/Linux-5.18-RNG). You can have a look at /proc/sys/kernel/random/entropy_avail which is always set to 256 now. Thanks again and best regards !

I've been seeing tutorial on how to setup ili9341 tft lcd and all of them are post from 2017 or older... tried doing it on newer version but I think ili9341 are not supported out of the box anymore by armbian

Hello, I tried to use the power button on my Rock 4 C+ running Armbian 23.02.2 Bullseye with Linux 5.15.93-rockchip64. It is able to power off. But I can't boot up the controller. When I use the debian based radxa image the button works like expected. I found this at the rk3399-rock-4c-plus.dts of the radxa kernel. &rockchip_suspend { status = "okay"; rockchip,sleep-debug-en = <1>; rockchip,sleep-mode-config = < (0 | RKPM_SLP_ARMPD | RKPM_SLP_PERILPPD | RKPM_SLP_DDR_RET | RKPM_SLP_PLLPD | RKPM_SLP_CENTER_PD ) >; rockchip,wakeup-config = < (0 | RKPM_GPIO_WKUP_EN | RKPM_PWM_WKUP_EN | RKPM_U…

I need to get an armbian focal image for the Rpi4b. I've checked in https://archive.armbian.com and it only shows the current jammy variant. If anyone could tell me where I can download the deprecated images, it would be much appreciated.

Hi all! Sorry about my English. I just started learning Armbian. Please don't scold me for my ignorance. I have an Orange Pi 3-lts. I installed an "Armbian_23.02.2_Orangepi3-lts_bullseye_current_5.15.93" OS on it. Transferred everything to EMMC. Installed Clipper. I started experimenting with the rotation of the display. (everything seems to have turned out as I wanted!) But damn! Wanted more! I wanted the startup process log to not be displayed on the screen when the OS was started. I read somewhere on the Internet: change in armbianenv.txt console = botn on console = serial. I listened and changed. And now I can't manage my OPI. I can't connect via terminal b…

Can someone please help me? I have a banana pi M3 board, and once got an Armbian image in this site https://www.armbian.com/bananapi-m3/ , and loved it! used it for a year, then my SDCARD have an issue, when i came to get the image link again all the links disappeared from the page, these images arent availble anymore? can someone please help me find an armbian image for bananapi m3 again?

Hi, I am a Grade 12 STEM Student, and right now I need someone's help on our Investigatory Project. Can someone help me on how to connect screen saver (turns off automatically when snoozing) and turns on when PIR Sensor detected something so that It saves power when not used. And I also need to know how do I connect it to the Smart TV because our project is basically an Interactive Board (The thing that you can find around malls which you can use to know specific locations around the mall.) What I have: 1. Orange Pi 2. PIR Sensor 3. Smart TV What I need: 1. A step-by-step procedure on how to do it. 2. What commands/codes to input (Right now, we are u…

Dear members My odroid c2 don't restart. I found this command in the forum: apt install linux-image-edge-meson64 linux-dtb-edge-meson64 linux-u-boot-odroidc2-edge Can i use it for odroid c2? What will be installed?

on orange pizero ,i installed pm-utils and with the pm-suspend command i put it in suspend . If I try to wake it up , with etherwake or other WOL programs (which send magic packets in LAN to the pizero's macadress) the pizero will not wake up . Do you know any tricks?

Hello. I tried installing Armbian_22.08.1_Orangepizero2_bullseye_current_5.15.63 on Orange Pi Zero 2. I am using it without display. It did get installed. However after updating and upgrading it did not boot at all. Can someone please help? Regards, Amol

Hello I'm a newbie and want to start my tour with my odroid c2 for the beginn i want to install a vnc server. So i tried to setup the port 5901 tcp (opoen/free) if i try ufw allow 5901/tcp i get ufw not found if i try iptables -a ........ dport 5901 i get dport not found So my question, is there any firwall on the default system? Thank you a lot

I just got my tinker board r2.0 today and installed the cli version of armbian. But it seems the wifi module is not regocnized. So also in the armbian-config under network there is no wifi option with SSID and Password fields. Any Idea how I can get it up and running? Also the ifconfig -a command does not show wlan0

Hello I'm new in Armbian. I'm trying to connect one Orange Pi Zero 2 to a 3d printer (board Cheetah v1.2) using UART in order to install Klipper to control the printer. I can't find how to enable the UART port to connect. I'm planning use UART 5 (pins PH2 PH3 according to this pinout http://www.orangepi.org/orangepiwiki/images/e/e3/Orange-pi-zero2-img4.png) . I've been searching for hours the right way to enable the UART communication, but I've not found a clear explanation about how to do it. I've trying armbian-config but Hardware option doesn't appears in the Menu. I'm using the Armbian_22.11.3_Orangepizero2_bullseye_legacy_4.9.318 image. Also, I've another q…

Hi. I was following a tutorial on how to set up my Orange pi PC. I installed this image: RetrOrangePi_v4.3_Armbian_5.97_Orangepipc_Ubuntu_bionic_dev_5.2.14_desktop.img. So I installed it. Everything ran fine and I can navigate the menus. The device I have is very similar to this one, it's a v1.3: https://imgur.com/FN1sBZF The problem is that, when I try to connect to the device using Filezilla it displays the following message: https://imgur.com/1WZI885 Yes the port I used is 22. Password: "PI" or "pi" I only have one ethernet cable, I plug that into the orange pi and I connect my PC using wifi. I've done this before with my Plays…

Hello everyone, I recently purchased an ili9488 touch screen for use with my Orange Pi 5, but I'm having trouble getting it to work. I've tried several solutions that I found online, but so far nothing has worked. Specifically, the screen isn't displaying any output when I connect it to my Orange Pi 5, and I'm not sure what steps to take next. https://a.aliexpress.com/_EQaN4gj - That is the screen I bought. For context,I have the latest version of the Armbian operating system installed. I've followed the instructions that came with the touch screen, and I've also tried several different solutions that I found online (including using the fbset …

Hello guys! I find it very convinient to see the temperature of the NVME drive installed while being logged on via SSH. How can I add the temperature of the drive right under the temperature of the cpu? I added a line: "echo -e "NVMe Drive Temperature: \033[32m$(sudo nvme smart-log /dev/nvme0n1 | grep temperature | sed 's/.*: //;s/ C//')°C\033[0m"" to the file /etc/update-motd.d/10-armbian-header What is the best way to do it?

Hi, Im using orangepi pc with armbian jammy. On download section there is only 2 choices, CLI and Desktop. Is there a custom desktop version where most (or if possible all) applications are not installed? It would take too long is I uninstall it one by one. I think I only need browser and terminal.

Hi!, I just bought my orangepi pc and also installed Armbian desktop. I also bought a wifi dongle with rtl8188gu chip. Is there any steps on how to use this to connect to my network?

I have owned numerous Raspberry Pi boards over the years, and I have always have ran Kodi on one of them. For years I have been wanting to upgrade my RPi 3 as it cannot play any of my H.265/HEVC videos. With all the shortages, and how old the Raspberry Pi 4 is getting, I made a rather spontaneous purchase for this Orange Pi 4 LTS board. Getting it all setup is easy enough, but of course, the video (even with H.264!) nearly maxes all 6 cores and the video is chunky as it's just doing everything without any video acceleration. Even navigating the menu seems slow and delayed. I have been scouring these forums and other sources for about 12 hours now, and I am sti…

I have an Orange pi 5 (could not find this in the tags list). I have created the Armbian micro sd card successfully I believe. However when I run this I get a long list of command line entries. I complete the enter password/user name entries then I end up at the following command root@orangepi5~# Then everything stops, no desktop just this command. Is it possible to get to the desktop by typing something into this command. As I understand it you should get one single chance to get to the desktop on first run, I apparently have not got this one chance. I believe I am trapped in the command line with no way at all to escape to the desktop. I will be polite and say I find t…

Hello I'm using armbian on a Neo 2 board and I wanted to use a Quectel EM05 or EC25 LTE modem with it. Actually only need the serial port to send AT-commands. My question is, are Quectel modems natively supported by armbian (QMI? MBMI? ), or do I need to add the driver manually and rebuild the image??? Thank you (Yeah, it's a noob question ) Edit: Ok, I connected to modem to the board and realized that a wwan0 interface was created. That's fine, but I actually needed the serial port ttySx in order to sen AT-commands, but there is not one available... that's actually very strange.

$ ip link 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000 link/ether 68:27:19:ad:02:09 brd ff:ff:ff:ff:ff:ff $ sudo lshw -C network *-network description: Ethernet interface physical id: 7 logical name: eth0 serial: 68:27:19:ad:02:09 size: 100Mbit/s capacity: 1Gbit/s capabilities: ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation …

Hello, I am planning to create a Kubernetes cluster from 5 Raspberry PI and one of the alternatives mentioned in tags, 9 hosts in total. I want to mount and customize the installation images with ssh keys, static IP address, etc, and to skip the initial script offered at login by the CLI images. Can you point me to the right piece of documentation? Thank you, Stefanita Vilcu