Amlogic meson

I can't upgrade armbian focal to bullseye.

Today I installed packages (apt-get upgrade): armbian-config armbian-firmware linux-buster-root-current-odroidc2 linux-dtb-current-meson64 linux-image-current-meson64 linux-u-boot-odroidc2-current and rebooted the system. Afterwards no more USB devices were found: Active USB Hub, USB Hd, USB mouse, USB memorystick Regardless if connected via USB Hub or directly. lsusb doesn't show any devices. Any hints? Thanks in advance

Hi all, as a small status update on the seafloor business, here are some pictures of the new Odroid C2 based instruments which will be deployed in September/October in the northers Pacific. Ten modules with different functionality will be deployed, all based on a standard setup of Odroid C2, TRB3sc FPGA based TDC DAQ system, one PADIWA preamp, and a modded mdedia converter serving as a fully configurable mini switch. One of the modules carries several Hamamatsu mini spectrometers, as well as a camera, to observe bioluminescence. Another module is targeting at muon tracking with SiPM based readout: …

Hello Forum, i am using a vdr headless server with 3 Technisat Skystar USB tuners for satellite television streaming. Before i used a raspberry pi 2 but because of limitations with its ethernet bandwith i went to odroid c2. System is now armbian with self compiled vdr with vnsi plugin, both out of git repo. System runs fine but after some hours (8h) a sporadic failure occurs and (USB?) system becomes unusable, To get the 3 dvb-s2 tuners running i increased the urb pool (USB request block) with kernel parameter "coherent_pool=6M" in boot.ini. I calculated that every of all 3 instances of driver needs about 512kB of USB buffer memory, without the option the first inst…

Hello. I tried the steps, but my Mecool KIII pro don't run using default conf extlinux.conf: label Armbian_community kernel /Image initrd /uInitrd fdtdir /dtb/amlogic/meson-gxm-mecool-kiii-pro.dtb append root=UUID=3bc7a8b8-73ee-4ade-9030-f3fa965fc27e rootflags=data=writeback console=ttyAML0,115200n8 console=tty0 rw no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 splash plymouth.ignore-serial-consoles But I need choose (unofficial) label Armbian-unofficial kernel /Image initrd /uInitrd fdtdir /dtb/amlogic/meson-gxm-mecool-kiii-pro.dtb #Insert the correct FDT line for your b…

I finnaly found it on google Here is the link: https://drive.google.com/file/d/1gVU-iGhoYALZNok6RMkUzWg0BhXTrWCt/view?usp=drive_link

Hi I'm wondering why chromium is missing from the ODroid C2 image when taking the non-desktop image and then adding the necessary packages to get a minimal X working? Planning to just build it from source, but wondering why it was missing from the core armbian distro? Is there a reason?

I've installed Armbian on a Odroid C4 board (running with emmc storage & connected to the orginal power supply). After a few hours or days, the board crashes & throws an error unable to handle kernel paging request at virtual address 000000000002e82e2... See https://pasteboard.co/NjIo5L6UR0Px.jpg for the complete error message System diagnosis information is uploaded to https://paste.armbian.com/aqahepelav

Would it be possible to get a "minimal" build of Armbian based on Ubuntu 24.04 (Noble) for the Radxa Zero 2? Thanks.

Hi! I try to use GPIO on BananaPi M5 board. But interface doesn't work. Armbian 23.05.1 Jammy with Linux 6.1.30-meson64. /boot/armbianEnv.txt: verbosity=1 console=both overlay_prefix=meson fdtfile=amlogic/meson-sm1-bananapi-m5.dtb rootdev=UUID=d099eb25-cf52-43fb-b826-535b9109637f rootfstype=ext4 overlays=w1-gpio usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u m5@bananapim5:~$ dmesg | grep w1 [ 7.568386] w1-gpio onewire@0: gpio_request (pin) failed [ 7.607814] w1-gpio onewire@0: gpio_request (pin) failed [ 7.620109] w1-gpio onewire@0: gpio_request (pin) failed [ 7.662444] w1-gpio onewire@0: gpio_request (pin) failed [ …

Hi - I'm running kernel 4.18.8-odroidc2 under stretch and I've installed linux-headers-next-odroidc2 linux-source-4.18.8-next-odroidc2 where the kernel image was linux-image-next-odroidc2 The system in general rocks - I was worried about not being able to use my RTL8812AU in the monitor mode - but it works! But I have 2 issues with 4.18.8-odroidc2, first the RTC PCF8563 module. The .config file includes the following entries CONFIG_RTC_DRV_PCF85363=m # CONFIG_RTC_DRV_PCF8563 is not set The Odroid C2 RTC shield is the one not set, namely, the PCF8563 …

Hello, I apologize, I can not speak English and have to write with google translator! will the mainline kernel master branch 5.1.y bionic and buster be finished before the support ends? so the display on hdmi and the hard disks on usb work and wlan?

I try to profiler the system, but could not find vmlinux binary and kernel debug symbol. The board is Odroid C4, SD card Image is download from armbian website Ubuntu 22.04.3 kernel 6.1.50-current-meson64 Thank you for help

Hi. Running Armbian Buster on Odroid C-2, Linux odroidc2 5.4.35-meson64 #trunk SMP PREEMPT Thu Apr 23 18:16:56 CEST 2020 aarch64 GNU/Linux With "armbian-config" I'm triyng to switch to another Kernel without success, error on "switch_kernel.log" file is: linux-image-dev-meson64=20.05.0-trunk.130 linux-dtb-dev-meson64=20.05.0-trunk.130 linux-u-boot-odroidc2-dev Any idea?

Hi, I broke my /boot on eMMC and my Beelink GT1 is in boot loop. I can't configure u-boot to boot from the SD card to reinstall it. Can you help me reconfigure u-boot to boot from the SD card? Thx printenv bootargs=rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.mem_address=0x20000000 ramoops.mem_size=0x100000 ramoops.record_size=0x8000 ramoops.console_size=0x4000 androidboot.selinux=permissive logo=osd1,loaded,0x3f800000,576cvbs hdmimode=720p60hz cvbsmode=576cvbs hdmitx= androidboot.firstboot=0 mac=86:48:d8:49:99:56 androidboot.mac=86:48:d8:49:99:56 bootcmd=run start_aut…

The latest apt-get upgrade on my board running Focal updated all but two (described below) of the following packages: armbian-firmware armbian-focal-desktop-xfce armbian-zsh bluez bluez-obexd libbluetooth3 libnss-myhostname libpam-systemd libsecret-1-0 libsecret-common libsmbclient libsystemd0 libudev1 libwbclient0 linux-dtb-current-meson64 linux-image-current-meson64 linux-libc-dev linux-u-boot-odroidc4-current python3-samba samba samba-common samba-common-bin samba-libs smbclient systemdsystemd-sysv udev This generated a new initramfs and uboot updates so I rebooted afterwards to make sure everything was ok. Now, the Light Display Manager has …

I want tou share with you my experience with weston with mali wayland drivers https://forum.odroid.com/viewtopic.php?f=138&t=28426&start=50#p213474 Wish list: Can you guys add /lib/udev/rules.d/99-mali.rules KERNEL=="mali",SUBSYSTEM=="misc",MODE=="0777" to for all board with mali GPU And also set up directory and library cache for mali userspace drivers so all application will use mali version istead of mesa We still have problem with v-sync with amlogic DRM driver

On the odroid c2 server I want to install jwm with xorg. What packages are needed for xorg? The log complains that it cannot find fbdev.

Is it possible to get it work, with next kenel?

I have a Waveshare 3.5inch RPi LCD (A): https://www.waveshare.com/wiki/3.5inch_RPi_LCD_(A) Does somebody have this kind of LCD running on a Odroid C2? Is there a step by step? Because the Waveshare or Odroid Wiki is over my head 😟

I cannot find the serial number with Armbian 23.02.2 on ODroid C4. On ODroid C2 with Armbian 22.11.2 and older versions it was readable on /sys/firmware/devicetree/base/serial-number. This does not exist anymore on C4. I do not know if it depends on Armbian version or board type.

Hi, after doing some last changes (hopefully) to Uboot and the kernel, I have some questions on how to get the new Uboot and kernel on eMMC (I can't reinstall everything on a cleanly etched system). I have normal build environment, with mainline kernel and v2017.11. compile.sh gives me a new image without problems. The target system is running nicely on a 128GB eMMC, but how can I safely install the new Uboot and the new kernel to my eMMC? I would really be happy to have one of the experts telling me how to proceed without killing my system Thanks in advance, any help is appreciated. Michael

Hello. Is worth to try this branch https://github.com/moonlinux/linux/tree/odroidc2-3.14.y-rt in order to build a realtime kernel upon https://dl.armbian.com/odroidc2/Debian_jessie_default.7z ? Thanks. Managed to install this https://github.com/moonlinux/linux/tree/odroidc2-3.14.y-rt , but the latency test is pretty bad: $ sudo cyclictest -t1 -p 80 -n -i 10000 -l 10000 -N # /dev/cpu_dma_latency set to 0us policy: fifo: loadavg: 0.45 0.33 0.15 2/154 1318 T: 0 ( 1318) P:80 I:10000 C: 225 Min:1000000 Act: 5962494 Avg: 6220148 Max:15955692

Hello, I am going start work with Odroid C2. In odroid C2, first need to install OS which they given in site or can i install linux based home automation software directly..?

Hello, Thank you for the great effort of Armbian having community support of this board. I have a Waveshare 4inch DSI LCD with touch that I want to use it with Radxa Zero 2 Pro. They have a device tree overlay provided for Raspberry Pi and drivers for different kernels for RPi And I found a kernel patch that seem to enable DSI here. ********************************************************************** I am using the latest build of Armbian for radxa-zero2 and it's Linux radxa-zero2 6.6.53-current-meson64 When I find /lib/modules/$(uname -r) -type f -name '*dsi*' It shows /lib/modules/6.6.53-current…

The proposed solution here (https://github.com/armbian/build/pull/4824) basically performs a power-reset of the SDCARD in the final moments in order to prepare for the bootloader's (Uboot) restart. What puzzles me is that the kernel has a Watchdog feature which seems to operating fine as witnessed by the console log "watchdog: watchdog0: watchdog did not stop!" meaning that the watchdog driver has been told to disregard attempts to disable it (which is fine in the context that the watchdog is being used to reset the cpu). The problem is, the watchdog never times-out because, i presume, something is still "kicking the dog" (there seems to be a worker thread tas…

Greetings all. Today I tried updating my Odroid C2 to image 5.22 posted on Oct 22, 2016. And I got the following error during apt-get upgrade: Setting up linux-u-boot-odroidc2-default (5.22) ... /var/lib/dpkg/info/linux-u-boot-odroidc2-default.postinst: line 5: conditional binary operator expected /var/lib/dpkg/info/linux-u-boot-odroidc2-default.postinst: line 5: syntax error near `function' /var/lib/dpkg/info/linux-u-boot-odroidc2-default.postinst: line 5: `[[ == function ]] && setup_write_uboot_platform' I peaked at the code in /var/lib/dpkg/info/linux-u-boot-odroidc2-default.postinst contains #!/bin/bash source /usr/lib/u-boot/platform_install.sh [[…

hi all . i think sd card is much shorter life time and restricted size ( 64G ~ 128G and big size is too expensive ). so as server , i like to use hard disk as root . for this purpose , nand-sata-install.sh is excellent ( but too complex for me to understand ) . i use nand-sata-install.sh on odroid-c2 armbian . and on working armbian , i run next script . ( the timing to attach sdb is about 10~15 second later after armbian booting ) . sda1 is cloned to sdb1 . clone-rsync-2-HDD-delete.bat ntpd -s date echo '--------------------' umount /mb1 mount /dev/sdb1 /mb1 df echo '--------------------' read X echo $X cd /mb1 mkdir -p bin etc home lib …

So as we know, the Hardkernel kernel did support powering the device on and off via a GPIO pin. This does not seem to work on Armbian with the mainline kernel. What does work is powering the device on and off with the remote control. So I wonder, what has to be done to enable power on and off vie the GPIO? My approach till now makes it possible to shutdown the device via GPIO interrupt. But then it will not come up again except if I reconnect the power cord or use the remote. I use this user device three overlay btw: /dts-v1/; /plugin/; /{ fragment@0 { target = <&ao_pinctrl>; __overlay__ { powe…

Can you fix build/patch/kernel/odroidc2-dev/packaging-4.x-DEV-with-postinstall-scripts.patch so we have working image with mainline kernel now it is missing symlink to zImage ln -sf $(basename $installed_image_path) /boot/zImage > /dev/null 2>&1 || mv /$installed_image_path /boot/zImage rm -f /boot/System.map* /boot/config* /boot/vmlinuz* /boot/zImage /boot/uImage And plz add https://github.com/BayLibre/libretech-image-builder/blob/libretech-cc-xenial-4.14-mali-x11/patches/0001-meson_drm_disable_ARGB8888.patch https://raw.githubusercontent.com/superna9999/LibreELEC.tv/Amlogic_GX/projects/Amlogic_GX/patches/linux/00…

Hi, On an Odroid C2, I used to read IP camera stream with ffmpeg without HW decoding, as it was not available yet. After reading many threads on this forum, regarding hw decoding through ffmpeg, I decided to give a try....but without any success. First of all, I tried to decode the Sintel.2010.720p.mkv file, and it worked well. This is the command I used: ffmpeg -c:v h264_v4l2m2m -i Sintel.2010.720p.mkv -an -vf fps=1 -f image2 -strftime 1 "/dev/shm/cam1_%S.jpg" (This takes a snapshot every second from the video file) And I got this output: [h264_v4l2m2m @ 0xaaaab68e84f0] driver 'meson-vdec' on card 'Amlogic Video Deco…

Now checked on Odroid C2 an image 5.76 with MALI and a media script, by a technique with replacement of u-boot, as for K2. Everything works fine. After installing the script, the standard browser began to play video 1080 full screen without brakes. MPV is just as easy to handle any full-screen video. Bonus has an in-house sound via HDMI. There is one caveat when configuring - it is necessary to specify the correct DTB option in the file for Odroid C2 "/extlinux/extlinux conf". 1. Copy of the standard u-boot from the working SD card. dd if=/dev/mmcblkXXX of=u-boot_odroid_c2.img bs=1M count=4 2. Burn the image Armbian for TV Boxing…

After some hours of compiling I got OpenCV 4.1.1 running on Armbian Buster 64-bit. The SBC is an Odroid-C2. Thank you for this great OS-image.

Hi, I use the C2 connector J2 signals to control power distribution for several attaches devices. A n-channel MOSFET is driven by a GPIO signal, with pulldown (3k3) to ensure that the n-channel MOSFET is off, - as long as the GPIO pin is in tristate or input state. I considered this to be the case for all "normal" GPIO lines (except I2C and SPI). I see now that after powerup, at least GPIOX_5 is active and switches on my load until I can export the GPIOX_5 and drive it low. Does anyone know if the GPIO lines are driven actively after powerup / reset? And if so, can this behaviour be changed in U-boot or kernel environment? The philosophy of t…

Hi, I want to change the resolution to a custom setting. In order to do this I changed the /boot/boot.ini file to custombuilt and include the relevant modeline for my display. When I start the odroid, it crashes. I then tried to just use setenv display_autodetect "true" and no preset selected, it also crashes. Perhaps I misunderstand auto_detect, but when I set the custombuilt option with the right modeline, it still won't work.. any ideas?

Hello, i download wiringPi library using, # git clone https://github.com/hardkernel/wiringPi # cd wiringPi # ./build as root, i compile library with errors. login as: root root@192.168.2.110's password: ___ _ _ _ ____ ____ / _ \ __| |_ __ ___ (_) __| | / ___|___ \ | | | |/ _` | '__/ _ \| |/ _` | | | __) | | |_| | (_| | | | (_) | | (_| | | |___ / __/ \___/ \__,_|_| \___/|_|\__,_| \____|_____| Welcome to ARMBIAN Debian GNU/Linux 8 (jessie) 3.14.73-odroidc2 System load: 0.00 Up time: 44 min Memory usage: 7 % of 1719Mb IP: 192.168.2.110 CPU temp: 47°C Usage of /: 13% of 15G Last login: Wed J…

Hello, I using up to date Armbian Stretch with kernel 4.19.41-meson64 #5.85 SMP PREEMPT Wed May 8 12:40:37 CEST 2019 aarch64 GNU/Linux. Today about 2 minutes after system boot I have found this warning in kernel log: May 12 07:51:48 xxx kernel: WARNING: CPU: 1 PID: 0 at kernel/time/hrtimer.c:917 hrtimer_forward+0x88/0xd0 May 12 07:51:48 xxx kernel: Modules linked in: cdc_ether usbnet uas xt_tcpudp nf_log_ipv4 nf_log_common xt_LOG xt_multiport xt_conntrack iptable_filter ipt_MASQUERADE iptable_nat nf_nat_ipv4 nf_nat nf_connt May 12 07:51:48 xxx kernel: CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.19.41-meson64 #5.85 May 12 07:51:48 xxx kernel: Hardware …

My buddy gave me his Odroid C4 when he bought a Raspberry and it has been reset for me to use. I plugged it into my new fibre modem. It has access to the internet. I have my PC upstairs with lots of videos I have downloaded. I used to use a WD box to watch my movies. I can't seem to get the new Odroid to connect to the network. I use windows 10 and didn't have a problem sharing files before. Does anyone have idea on how to hock the systems so they will share files??? Rod

Please contribute if you're affected: https://github.com/igorpecovnik/lib/issues/499

Hello, I tried to build a fresh image for the Odroid C2, but always fails with the u-boot.bin. The error is equivalent to the Issue #452 on Github. Anyone else with this problem? Thanks in advance.

Hello Experts, I was hoping to get some beginner help getting my TV's remote control working with my Radxa Zero 2 micro computer running Armbian_23.11.1_Radxa-zero2_jammy_current_6.1.63_xfce_desktop or any armbian OS if there is a better one that can do CEC out of the box. I have installed v4l-utils and cec-utils, but when I use the command cec-ctl there is an error: Failed to open /dev/cec0 I know my Samsung tv/hdmi connection is good and the remote works with my raspberry pi 4 with LibreElec, but it seems like this Radxa Zero does not recognize the HDMI/CEC device and its not installed. The Raspi4+LibreELEC works with my TV out of th…

Before I was able to manually send CEC commands to my tv with cec-client. However I'm not sure how it works with Linux kernel CEC implementation. I know /dev/input0 is the node for CEC, I just have no idea what to do in this case. In case of cec-client, I would use the website cec-o-matic, but is there also a site like this for the kernel implementation of CEC? The reason I want this, is because I need to power on a tv with a remote using the odroid.

Hi, all I have tested all the bookworm images and they all have the same error. HDMI debugging not working... This is the log uart Armbian_23.5.1_Nanopik2-s905_bookworm_current_6.1.30 Regards npik2-armbian

My NanoPiK2 is installed with Armbian Focal desktop system. When I used it normally for a day, I manually shut it down (closed properly). But when I restarted it, it finally displayed and stayed at [OK] Reached target Host and Network Name Lookups. Unable to enter the system. I tried to insert the SD card into the computer to search for the boot logs, but I couldn’t find it. How do i solve this problem？THANKS

I am trying to enable the external antenna on my Radxa Zero SBC. I was assuming that there is a kernel overlay available to achieve this, but unfortunately not. At least I am unable to find it using armbian-config. I am running Armbian v24.11.1 with kernel 6.6.63-current-meson64. Has anyone ever achieved to enable the external antenna? Any hints appreciated.

Hi, I am trying to get the official Hardkernel RTC board working. This board requires the driver module "rtc-pcf8563.ko" which is not included in the image by default. So I went through the kernel compiling tutorial, to add this module to my "own" kernel, and copy it over to my main system. First problem: the kernel version was different: main system is at version 4.18.8, while the module was compiled for 4.18.20. I could fix this by myself be defining the KERNELBRANCH='tag:v4.18.8'. Second problem: the "linux family" has changed. My main system is at Armbian version 5.60 for family "odroidc2". The driver module was compiled for "meson64"…

ODROID C4 : How can I configure SDIO bus on GPIO 40 pins ? I beleave that ODROID-C4 GPIO 40pins supports SDIO bus by SoC GPIO pin configuration. How can I get such pin configuration, that enables SDIO bus on GPIO 40 pins? Are there someone who got such configuration? Thank you .

TJoe says Thank you!

Hi, Armbian_21.02.3_Odroidc1_focal_current_5.10.21 how do I find out which number do I need to provide to gpio export command? Let's say I have physical pin 16, which is labeled by the manufacturer as `GPIOX.5` or `102`. But that doesn't work with Armbian: echo 102 > /sys/class/gpio/export [ 1602.030617] export_store: invalid GPIO 102 How do I know the value to provide for /sys/class/gpio/export? # cat /sys/kernel/debug/gpio gpiochip1: GPIOs 413-428, parent: platform/c8100084.pinctrl, aobus-banks: gpio-416 ( |TF_IO ) out lo gpio-417 ( |usb-hub-reset ) …

hi, i recently created a game that i would like to install over 905x3 tv box, i would like to protect it from copy. is there a way to encrypt the whole ROM without the need of any external hardware or password to be entered each reboot ? tv box launch directly into the game and every possible way to interact with linux is disabled (keyboard, usb, lan) and i only need to encrypt the ROM to make the game more resistent in some extent to copy. i read about encrypted bootloader but i'm not sure if that is what i need. can i only encrypt the game bin with a key that is protected inside the 905x3 ? (beside cpuid as it seem easy to reverse). …

Hello, Recently I have discovered bug in kernel or maybe iptables with using Huawei E3372h LTE Hi-Link USB dongle (or maybe other devices which exposes HTTP interfaces over cdc_ether). Odroid enters into kernel panic and reboot. I am using ARMBIAN 5.85 stable Debian GNU/Linux 9 (stretch) 4.19.42-meson64. kernel:[ 60.801868] Internal error: Oops: 96000004 [#1] PREEMPT SMP The steps to recreate the bug: 1) disable or remove NetworkManager, use only IPv4, 2) set network interfaces in /etc/network/interfaces source /etc/network/interfaces.d/* auto lo iface lo inet loopback auto eth0 allow-hotplug eth0 iface eth0 inet static address 1…

# uname -a Linux odroidc4 6.6.63-current-meson64 #1 SMP PREEMPT Fri Nov 22 14:38:37 UTC 2024 aarch64 aarch64 aarch64 GNU/Linux Installed latest "Armbian_24.11.1_Odroidc4_noble_current_6.6.60-kisak.img" ...with latest sudo apt update; sudo apt upgrade, rebooted... Hardware: - Odroid-C4 - Sabrent USB 3.0 to 2.5-Inch SATA Adapter; Model: EC-SSHD with latest firmware patch, connected to a Kingston SSD: SA400S37480G # dmesg -l emerg,alert,crit,err [ 0.879290] meson-drm ff900000.vpu: DSI transceiver device is disabled [ 3.402246] systemd[1]: Failed to start systemd-sysctl.service - Apply Kernel Variables. [ 4.327154] panfrost ffe40000.…

Still trying to get the wireless working... Followed directions here, and during the "make ARCH=arm64", I get the following: compilation terminated. scripts/Makefile.build:308: recipe for target '/Downloads/WiFi/rtl8192cu-fixes/core/rtw_cmd.o' failed make[2]: *** [/Downloads/WiFi/rtl8192cu-fixes/core/rtw_cmd.o] Error 1 Makefile:1278: recipe for target '_module_/Downloads/WiFi/rtl8192cu-fixes' failed make[1]: *** [_module_/Downloads/WiFi/rtl8192cu-fixes] Error 2 make[1]: Leaving directory '/usr/src/linux-headers-3.14.73-odroidc2' Makefile:584: recipe for target 'modules' failed make: *** [modules] Error 2 Now what???

I needed a kernel upgrade to be able to run some applications. I value stability over cutting edge features so I decided to try the Debian image. However I detected a few things that are not working properly. 1. USB almost never works. Most of the time my very plain USB keyboard won't be detected. There is an error message right at the start of the boot sequence "Failed to get keyboard state from device[...]". I have to shutdown and start multiple times by plugging off the power cable and I also keep trying different USB ports. Some rare times the keyboard will work though, even with the above error message. Even rarely I don’t see the error message at the boo…

Hi. I want to use CAN interface on ODROID C2 board. I use external CAN-bus controller like MCP2515 via SPI interface. So, i need to enable SPI and CAN-bus peripherals and in kernel. So, could someone explain me how to do that? I know about device tree, but don`t know what to do. Just give me some guide links about device tree management, any examples, etc.

I am trying to connect a PPS source to an ODROID-C2 board using GPIO. I am running Armbian 19.11.3 Buster, with kernel 5.3.11-meson64. I downloaded the Armbian kernel source for this kernel, added the following to meson-gxbb-odroidc2.dts, and compiled and installed it: pps { compatible = "pps-gpio"; gpios = <&gpio GPIOY_3 GPIO_ACTIVE_HIGH>; status = "okay"; interrupt-parent = <&gpio_intc>; interrupts = <26 IRQ_TYPE_LEVEL_LOW>; }; When I boot and load the pps-gpio module, I get the following error: pps-gpio pps: failed to map GPIO to IRQ: -6 pps-gpio: probe of pps failed with error -22 …

Hello, I installed Armbian on my Odroid C2 and need to run a 32-bit application. When I try to run it I get No such file or directory so I tried to install ia32-libs but can't find it for Armbian, even tried to compile the application on my Odroid C2 but it runs out of memory (tried with swap files too but it didn't work). Can someone lend me a hand please? Thanks

Hi, maybe someone can give me a hint... I have a running system now on 128GB eMMC card, and wanto to use GPIO. I have /sys/class/gpio/ with export, and unexport files, and two gpiochip0 and gpiochip14 entries. Unfortunately I can't export pins, as export 231 > /sys/class/gpio/export gives me a (as user and root) bash: echo: write error: Invalid argument Any help is appreciated. EDIT: works now. It is somehow a bit complicated, as the "usual" numbers as known from 3.x kernels vanished. Debug output shows two "gpiochips", with a certain number of pins, which you have to correlate to the device tree enums for that "chips" - …

I did a quick install of the desktop image for the ODROID C2. It sees no audio devices (HDMI - or any of the half dozen or so USB Audio devices I quickly tried). However, I have a app I wrote that builds a custom "kitchen sink" version of FFMPEG (everything is enabled). I built it on the C2 (to get a compile time), and noticed the sound did work from the app (and it sounded great). I wish I would have had more time to investigate why no audio devices are detected, and further, why I am able to play sound (only from the one app). Sorry. I am just trying to be helpful in saying "hey - the sound IS there - some users just may not be able to immediately get to…

Hi all am trying to make a router out of my odroid c2 using the mainline kernel but am trying to configure mini jumbo frames to support my PPPoE on a FTTP line but am getting errors from the kernel when attempting to enable the 1508MTU needed to support it. my question is do these adaptors support jumbo frames on any kernel or is it just the mainline kernel not supporting them.

Hi everyone, I have Radxa Zero 4GB-64GeMMC model. I'm using latest Armbian (22.05.3) on microSD card. I want to connect my portable SSD (500GB) to RZ with USB3.0 hub that has additional power imput to support energy hungry devices. I checked usb hub is working with 16GB usb flash. My ssd use realtek RTL9210 chip. I also get similar problem with 32gb mSD card formatted with FAT32. When I connected the SD card reader, other device that uses same hub become slaggish and do not working properly. If I unplag sd card or ssd everything back normal. I thing there is a driver problem. Radxa Zero Diagnostic Dump

Hello Igor, In past threads, it seems a bit argued about the zram module, but will not the zram module be enabled by default on other arm boards? I am using odroid-c2, but it is effective in hardkernel? It seems that it is becoming. If possible, if Armbian seems to have no problem, I want it to be valid. https://forum.odroid.com/viewtopic.php?f=136&t=20116 $ grep "ZRAM" /boot/config-3.14.79-odroidc2 CONFIG_ZRAM=y # CONFIG_ZRAM_LZ4_COMPRESS is not set # CONFIG_ZRAM_DEBUG is not set $ lsmod | grep zram $ cat /etc/armbian-release # PLEASE DO NOT EDIT THIS FILE BOARD=odroidc2 BOARD_NAME="Odroid C2" VERSION=5.31 LINUXF…

C2 running FAB! http://forum.armbian.com/index.php/topic/2422-more-proper-testing-better-armbian-experience/page-2 Many thanks to Miike for the great wallpapers; http://forum.armbian.com/index.php/topic/2417-armbian-wallpaper-remake/

Hello I use the odroidn2 build, (slightly patched with dts add patch) for my Dreambox one/two (s922X). My Broadcom Wlan chip BRCM4356A2 is not supported in either etch or current. This patches: https://github.com/armbian/build/blob/master/patch/kernel/archive/meson64-6.0/general-meson-mmc-1-arm64-amlogic-mmc-meson-gx-Add-core-tx-rx-eMMC-SD-SD.patch https://github.com/armbian/build/blob/master/patch/kernel/archive/meson64-6.0/general-meson-mmc-2-arm64-amlogic-dts-meson-update-meson-axg-device-tree.patch prevent that. https://pastebin.com/Cbvd82R8 If I go back to the previous patch: https://github.com/armbian/build/blob/master/patch/kernel/ar…

Hello, A GPS module ublox is connected to a odroid c2 board on GPIOX.12 and GPIOX.13 for the RX and TX and GPIOX.10 for the PPS. The board is running the stable kernel 4.19.42-meson64 from Armbian based on Debian stretch which was dist-upgraded to Debian buster. I am trying to get the /dev/pps0 entry using GPIOX.10 to finish the chrony setup but I cannot find the correct syntax in the DTS file. Any pointer or idea ? I try either of the gpios line below, none of them seems to be correct. pps { gpios = "< 0x1e 0x66 0x0 >"; #gpios = "<&gpiox 10 GPIO_ACTIVE_HIGH>"; #gpios = "< 0x66 >"; assert-fall…

Hi, Having problems with instalation of certbot on latest armbian and Odroid C2...; root@odroidc2:/etc/apt# apt-get install certbot Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: certbot : Depends: python-certbot (= 0.8.1-2~bpo8+1) but it is not going to be installed E: Unable to correct…

I'm using an Odroid C2 and need some newer software packages than those found in the Ubuntu 16.04 repositories, so I installed the legacy (3.14.79) version of the Debian server edition of Armbian, then upgraded it to Debian 9. I've installed xorg, lightdm, etc and now have a very functional desktop. However, I want to install a 3D CAD program that **I think** would perform better if I had 3D accelerated graphics installed. I'm a complete noob when it comes to 3D graphics drivers. I assume they're not installed, as I see this on my Orange Pi PC 2 running the desktop version of Ubuntu: $ lsmod | grep mali mali_drm 2732 1 drm …