Allwinner sunxi

Hello, running ARMBIAN 5.59 stable Debian GNU/Linux 9 (stretch) 4.14.65-sunxi on Banana Pi pro /var/log is always full df -h /dev/zram0 49M 48M 0 100% /var/log root@mail:/etc# zramctl NAME ALGORITHM DISKSIZE DATA COMPR TOTAL STREAMS MOUNTPOINT /dev/zram0 lz4 50M 47.5M 7.8M 8.4M 2 /var/log /dev/zram1 lz4 249.7M 4K 63B 4K 2 [SWAP] /dev/zram2 lz4 249.7M 4K 61B 4K 2 [SWAP] Since i am running on sata (ssd of 128gig) i dont need that. Cannot find how to stop the mount of /var/log on /dev/zram0. Not in fstab. Want to use the real /var/log from / (root).

Help me! 1. I was downloaded images from https://www.armbian.com/orange-pi-prime/ 2. then write to SD Card (32Mb) using Etcher (i was try Ubuntu and Debian) 3. insert card, turn on power, begin loading 4. but i see "starting kernel" message and loading stopped! Why?

Hello, Just find out that my USB ports are not working. Quick dig shows that the are disabled: # lsusb # dmesg |grep usb [ 0.000000] Kernel command line: root=UUID=e8491c09-2260-4706-a9a4-1f9f96af1232 rootwait rootfstype=ext4 console=ttyS0,115200 console=tty1 hdmi.audio=EDID:0 disp.screen0_output_mode=1920x1080p60 panic=10 consoleblank=0 loglevel=1 ubootpart=5b507211-01 ubootsource=mmc usb-storage.quirks=0x2537:0x1066:u,0x2537:0x1068:u sunxi_ve_mem_reserve=0 sunxi_g2d_mem_reserve=0 sunxi_fb_mem_reserve=16 cgroup_enable=memory swapaccount=1 [ 1.308752] usbcore: registered new interface driver usbfs [ 1.308799] usbcore: registered new interface driver hu…

Встроенный микрофон не работает при установке рабочего стола.

Welcome to Armbian Bionic with Linux 5.4.20-sunxi This is the thing I have installed... I'm trying to use the serial ports out of the GPIO header, nominally pins 8 and 10 which depending on what you read maybe ttyS1 or ttyS3. Out of the box whatever they are they're not available. After much googling, I've seen stuff about FEX and DTS none of which mean much to me, I'm guessing Bionic doesn't use FEX as there's no sign of .FEX or .BIN files in the /boot directory. The default state seems to pump garbage out the tx line whatever its doing. Minicom promises to talk to any ttyS? I give it, but theres no answer on loopback, And that's all I have. …

Hello all ! I connected relle to pins (Physical): Relle Orange in 35 gnd 6 ucc 2 But it is constantly active (on), although the port status 32 is off (0). Why is that? # gpio write 24 1 Changes the port status, but has no effect on the relay. Relle ist ON alweys! If you physically disable the pin (in - 35), then the relay is turned off. I just installed the system. I did not install any additional services and packages. Maybe I need to configure something in the system to activate the GPIO?

For information purposes, that the 1.3-inch SH1106 OLED connected to I2C on OZPI v3 works very well OLED connected to PIN 3 of SDA and PIN 5 of SCK and in armbian-config in HARDWARE set to [*] i2c3-ph Using tools i2cdetect -y shows that the OLED is at address 0x3c All Python code with the adafruit library works fine

I need some help with this LCD https://www.amazon.com/dp/B0CMD7Y55M?ref=ppx_pop_mob_ap_share, i bought it since i verified whith the always unreliable AI GPT if it would work with my Orange Pi since i want to use the screen in my klipper 3d printer. Now im stuck since the available driver from the manufacturer are only for the Arduino and RP2040. I verified evrywhere and could only find one github but that one did not work for me and there are no tutorials of how to work with this. Does some one have any idea of how to make this run or work?. Just in case my wiring is as follows:

Help! I used your overlay, but nothing works for me. Orange pi zero 3 (Armbian Linux 6.12.35-current-sunxi64) overlay: /dts-v1/; /plugin/; / { compatible = "allwinner,sun50i-h616"; fragment@0 { target = <&spi1>; __overlay__ { status = "okay"; cs-gpios = <&pio 7 5 0>,<&pio 2 15 0>; /*PH5=CS0 for lcd, PC15=CS1 for touch*/ display: display@0 { compatible = "ilitek,ili9341"; reg = <0>; pinctrl-names = "default"; spi-max-frequency = <20000000>; rotate = <270>; bgr = <0>…

Hello! Is there any hope to acquire a r3p2 or a newer Mali driver support in an armbian kernel for Banana Pi?

Hi, Thanks for the excellent distribution I noticed that in the hardwareinfo script there is no bananapipro result and when I boot new vanilla 4.5 Kernel the banana.dtb file is used instead of the bananapro.dtb As a result, no wifi, see also last two replies here for similar issue with M1: http://forum.armbian.com/index.php/topic/340-banana-pi-m1plus-no-wifi/?p=2138 Dirty Solution: hardcode loading bananapipro.dtb in boot.cmd. Wifi works This is result of "cat /proc/cpuinfo"

Good day all. Anyone having issues of not able to see anything after "Uncompressing Linux... done, booting the kernel." via serial console on Lamobo R1 ? Tried to experiment a bit, it seems that U-Boot works correctly, but in Linux kernel, sent data from USB-serial to ttyS0 arriving correctly, but anything written to ttyS0 is not visible on connected USB-serial adapter.

Hi, I'm fairly new to linux and I've been trying to get my banana pi OTG port to act as a HID device when plugged in. I've been looking to do it using configfs and usb_gadget but I have no idea how to get this working. Do I need to compile the kernel with additional options to get this working? I've googled for days now and tried various different solutions but not got far with it. Any help is much appreciated.

Hi, I tried to use default audio device, audiocodec hw:0,0 with arecord to record some sounds from mic. The file contains some noise. Any ideas how to activate mic?

For some reason still unknow to me, my OrangePi Lite Wifi became unreachable twice. I should have checked whether it was something more. Anyhow, temperature is an issue that everyone says about, but I do not believe it is. To determine when Orange Pi Lite Wifi becomes unreachable I wrote a Python script (nothing special, similar to many on the Internet) that posts the ARM7 temperature of Orange Pi Lite to ThingSpeak platform (owned by Matlab). If, and when my Orange Pi Lite Wifi, becomes unreachable I will know as it will stop sending posts to ThingSpeak. Besides the main interest, I do something useful as I monitor the temperature of ARM7. (the image though it shows…

I was sort of disappointed with my RPi 2 VPN performance, which is about 2.5MiB/s while normal traffic can easily exceeds 5.5MiB/s. So I setup same VPN config on OPi One and run the test. The speed is impressive which is well above 5 MiB/s but it could only last about 10s before the box reboots itself. I can see one cpu core is occupied 100% by softirqd ( about 80% on RPi 2). My kernel version is 3.4.112 and StrongSwan version is 5.3.3. Don't have further information yet. When I get a chance to hook up serial console, I may collect more info.

I have a question ...is it possible to run : Medion X10 (WiFi) remote control ? http://www.x10receiver.net/info_supportedremotes Unfortunately, after the command irw I do not get any information ...... I'm not too good at linux :-( Armbian system detects this as a pilot ! lsusb Bus 006 Device 003: ID 0bc7:0006 X10 Wireless Technology, Inc. Wireless Transceiver (ACPI-compliant) cat /proc/bus/input/devices I: Bus=0003 Vendor=0bc7 Product=0006 Version=0100 N: Name="X10 WTI RF receiver" P: Phys=usb-sunxi-ohci-1.2/input0 S: Sysfs=/devices/platform/sunxi-ohci.2/usb6/6-1/6-1.2/6-1.2:1.0/rc/rc1/input9 U: Uniq= H: Handlers=kbd event9 B: PROP…

Hey, I was wondering if anyone came across the board layout files. If eagle cad files were available that would be great! I'm assuming that they dont exist.. Or has someone designed a hat or shield for the OPi0? I want to design one and was hoping someone else beat me to it. If not i'll just have to measure it out and make it. I dont want to reinvent the wheel so that would be cool Thanks

I just did an apt-get update on the mainline version of armbian and now the machine won't boot. I'l looking at the uboot output and it appears not to load the full kernel in and boot it. The strange thing is it seems to hang, but when I unplug the power, the kernel load info shows up on the serial output. U-Boot SPL 2017.03-armbian (Mar 15 2017 - 06:57) DRAM: 512 MiB Trying to boot from MMC1 U-Boot 2017.03-armbian (Mar 15 2017 - 06:571 +0100) Allwinner Technology CPU: Allwier H3 (SUN8I 1680) Model: Xunlong Orange Pi Zero DRAM: 512 MiB MMC: SUNXI SD/MMC0 *** Warning - bad CRC, usig default environment r serialial Net: phy interface0 eth0: ethernet@1…

Hello, I have started on Armbian Ubuntu on a Orange Pi PC and have some difficults to follow the tiny font on the terminal emulator. In order to change the fontsize, I used the command "dpkg-reconfigure console-setup" and choosed the Terminus font with a bigger size. But no effect after reboot. With which trick a modification can be performed? What is with the fonts marked with "framebuffer"? If a modification is not possible with the Armbian terminal emulator, can I use an alternative? So I miss a property button as available on Raspian. Thanks for yor help and best regards Walter

What is the latest version of Armbian tested and proven working with a gc2035 camera module, please? I tried a few months ago and ran into so many issues, I gave up. Camera works in Android, didn't work in the Armbian I tried, and was eventually advised to try an earlier version that I couldn't easily find. I decided to defer the problem, but it is now more pressing. Thanks in advance for info and advice. Regards, Charlie

Hi All, I'm using the latest Debian mainline kernel image -> Armbian_5.31_Micro_Debian_jessie_next_4.11.5. I can't get the USB OTG port to work as host only. I was using the legacy kernel before and below setup was working for me -> [usbc0] usb_used = 1 usb_port_type = 1 usb_detect_type = 0 usb_drv_vbus_gpio = port:PB09<1><0><default><0> usb_restrict_gpio = usb_host_init_state = 1 usb_restric_flag = 0 I read on another post that usb0 mode is host on armbian images by default. I also read about needing to load the g_serial module for Banana pi, but I don't think it's required here. Do I need to make any changes to th…

I installed the experimental version of the NanoPi Neo Air distribution on my Air a month or two ago. At the time I believe Bluetooth was not working on that version. I don't see any indication that it is not working now, but it doesn't seem to be working on my install. Is Bluetooth working on the experimental kernel? If so, should I just re-install, or is it not hard to get it working on an existing install? I just installed the latest updates and rebooted, and that didn't fix it. The symptom that I'm seeing is that if I run bluetoothctl it prints a prompt, but seems to lock up.

Hi, i'm new on this forum. I have compiled u-boot 2017.3 and Mainline 4.14 for my own for Olimex-olinuxino-micro-emmc - and it is runnig ;-) But when i reboot the board, u-boot hangs with: U-Boot SPL 2017.03+ (Oct 03 2017 - 18:24:31) DR Only reseting or repowering helps. any ideas?

Hi, I have a BananaPi and BananaPi Pro connected to the Lemaker 7" TouchLCD. When I boot the system, I can't see any console output. I only see a flashing cursor in the left top corner and then it starts the X-window-manager. What do I have to change to see the boot messags on my LVDS LCD? I have tried to change the console=both value to tty0 or tty1 via armbian-config, but this doesn't work. Any ideas? Here is the output from cat /proc/cmdline: root=UUID=e9635572-227e-485c-b76d-b4f0d6d34394 rootwait rootfstype=ext4 console=tty1 console=ttyS0,115200 hdmi.audio=EDID:0 disp.screen0_output_mode=1920…

Hi, I have two OrangePi Lite running side by side. After working fine for about 8 months both started to experience same issue with wireless: The board works randomly for few hours or few days and then looses wireless connection. When this happens reboot does not help as then issue occurs immediately after the boot. Unplugging and replugging power source resolves that for a while and then happens again I suspect it may not be related to a hardware issue or wireless hotspot, as I have at least 3 other clients that continue to work fine. Searching for it on the internet brought this issue with Raspberry Pi: https://github.com/raspbe…

orange pi one h3 512mo ram didn't boot up and it stop at starting kernel this happend for both armbian version in the armbian website , i tryed also a version from the official website of orange pi one and it pass this step but show black screen .is there any image work properlly on orange pi one H3 please hekp

I had success with @ubobrov's sunxi-cedar-mainline driver before on H3 devices. I'm trying to get it to work on the Orange Pi 3 LTS (H6) however it keeps giving the following error: sunxi-cedar 1c0e000.video-engine: syscon failed... Any help would be much appreciated. dmesg: [ 6.167614] cedar_ve: loading out-of-tree module taints kernel. [ 6.167700] cedar_ve: module verification failed: signature and/or required key missing - tainting kernel [ 6.168445] sunxi cedar version 0.1 [ 6.168601] [cedar]: install start!!! [ 6.168654] cedar_ve: cedar-ve the get irq is 23 [ 6.168673] sunxi-cedar 1c0e000.video-engine: assign…

Hi, I've bought Orange Pi Prime from the second hand. I've also bought 5V 3A power supply. It it was booting with Debian and Armbian. I was using Kingston SDHC cards. Suddenly my board stopped booting from mmc card. I also tried to boot it from Sandisk A1 class card but with no success. Do ypu think it is hardware malfunction or something else?

Hi, i have an orangepi zero 2w and tried noble gnome image with the "current" kernel (v6.6.x). I activated the gpu via armbian-config and reboot. Then it stucks somewhere in the booting process. It shows nothing on the screen. If i use the orange pi image instead, i can activate the gpu with orangepi-config, which is a similar tool like armbian-config. The gpu works fine then and has great performance. So it's theoretically possible. Can someone explain to me what the problem is here. If it was a simple port, it would surely have already been done. I tried also the dtb from the orange pi image, but then it also didnt boot up. Th…

Dear Community, I currently want to reduce the transmission power of the NanoPi Neo Air. This means that I simply want to be able to set the Wifi transmission power in 10% steps, for example. What I have already tried: Instructions according to Wiki: OpenWrt image is not flashed. No access via browser. But it doesn't matter: max. transmission power is used in AP mode. Setting as in the Wiki image "TransmitPower:auto" probably does not apply here anyway. Network Manager TUI via "sudo nmtui" has no such settings. Adjust the NVRAM files in "/lib/firmware/brcm" or "/lib/firmware/ap6212" step by step. All changes are …

While doing some testing of multiple things I decided to build 2 images, fresh/new for my nanopineo's also trying to have the resulting image as close as possible to what I have running on the nanopineo's for years since 2022 or so. That was originally Armbian Buster and I have been tweaking the installations to match other computer installations. Main thing is split the root partitions into a rootfs (Btrfs) and a bootfs (Ext4). More recently, I did more changes, such that I can run the whole image as KVM and/or systemd-nspawn container. The 1st image was adding extension 'u-boot-menu'; build ended in success, but have not tested it on HW. I saw in extlinux.c…

Hi. Can anybody give me any idea on how to find out why it is crashing? I recently moved to this distro, and it is now crashing after 1 to 4 days of continuous usage. The thing is, I have no idea how to find out why it is happening, and how to fix it. Which log should I go for? I was running this Aruntu before, and never had this issue, which seems to show that this is not an hardware issue. Best, João

HI, i get the failure "***warning - bad CRC, using default environment" and the system don't boot. I tested it with an banana pi, cubieboard2 and olimex A20 Olinux Lime2 and all the same failure. Of course with the specific image. I flashed the image with ubuntu 14.04 lts (no virtual maschine) with dd bs=1M if=filename.raw of=/dev/sdb. I using the direkt letter of the drive sdb and not the specific partition sdb1. The windows flash tool dont works, i get an error when click on "copy", whats that, missing framework? What i make wrong?

Hello everyone, I'm having some isues with my olimex board. It boots fine on the images supplied by olimex. But the Armbian legacy images wont boot. I have a serial connection to the board it hangs on the following line: <6>axp20_ldo2: 1800 <--> 3300 mV at 3000 mV. http://pastebin.com/nEHAiZHa I need legacy for i2s support so mainline isnt an option. I use the following board(tried 3 of these): https://www.olimex.com/Products/OLinuXino/A20/A20-OLinuXino-LIME-4GB/open-source-hardware I used the following armbian image (jessie and wheezy give the same error): http://www.armbian.com/olimex-lime/ Building the image myself also doesnt work.…

I was installing real time clock on Orange Pi One board ... , after some unsuccessful tries I found that the battery has bad solder and all is fine now date was set "up" and "down" ... from Sat Jan 1 02:06:23 EET 2000 to Thu Jul 8 21:37:42 EEST 2032 several times ... and during all this time armbianmonitor was running (I did not check it every time ... I made many reboots ) now armbianmonitor shows some "static" data , in which the time is always 0:18.50 ... and I am thinking that may be it is showing the "last" recorded , I mean the higher date/time ...which is somewhere in the future 2032... I try reinstalling armbianmonitor ... did not helped how to remove …

I got my lite days ago, and have tried lots of images, none of them can recognize the build-in wifi Instead, a eth0 device is presented. is it the actual wlan? Armbian gives me the best compatibility so far (in terms of usb support) I can read the chip module is printed realtek 8189FTV, but lsmod shows me a 8189es module loaded. By google around, no luck for the FTV version driver. I also played with the script.bin, but still no luck. Anyone can give me some hints. Thanks.

Hi, I've recently acquired some nanoPi M1, and just about now installed ARMBIAN. However I can't seem to get any sound working via 3.5 analog jack. Volume is set right on alsamixer Speaker are working and volume is set at max Soundcard is listed but yet I have absolutely no sound ... any ideas ? root@user:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: audiocodec [audiocodec], device 0: SUNXI-CODEC sndcodec-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: sndhdmi [sndhdmi], device 0: SUNXI-HDMIAUDIO sndhdmi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 root@user:~# cat /proc/asound/cards 0 [audiocodec ]: audiocodec -…

Hi, I yesterday built a new image for my A20-OLinuXino-MICRO board (Armbian 5.17 Jessie with kernel 4.7.3) At first boot, everything worked fine. I could manage to connect through SSH and changed root password and add new user. However, avec adding a Hard Disk (on the SATA connector) and reboot, I could not manage to connect via SSH So I tried the serial (UART) connector. After some tries and a non responding console (I could see no kernel messages at boot to I had to change the verbosity), I finally succeeded in booting with a console prompt on serial connector. But... The keyboard is not responding on that serial connector. After a few tries,…

Hi, I bought nanopi_neo boards (for my hobby projects). I am learning about security. I am able to dump e-Fuse area at uboot stage. But i can't modify it (i want to write my own key). I don't have any memory map information of e-fuse. In present boards, bootROM is not verifying the uboot signature(RSA sign:-)). 1) How to enable signature verification in bootROM? 2) Is there any code or information regarding BootROM security and e-Fuse area mapping? 3) Is there any support of TEE (Trusted execution environment)?

Hi, I'm trying to send IR command from a IR led from an Orange Pi, i have it working fine on an Arduino, but it seems that on linux it's a bit more complicated as there are no lib that can control a GPIO with an IR transmitter, it seems that everybody is using LIRC. I see for raspberry pi this needs to be done : EDIT /etc/modules WITH : lirc_dev lirc_rpi gpio_in_pin=23 gpio_out_pin=22 the Orange PI devier module is different, so i do not know how to control it to let it know where the transmitter is. Anybody managed to get this to work ? Thx

I've got a BPi Pro with a PMP as a sort of backup box. It appears to be running find so far and I'm not running RAID of any sort on it as I've had issues with that an PMPs on other platforms. The question I have is dmesg is filling up with entries like this: [66451.217935] sdb: sdb1 [66752.272509] sdb: sdb1 [66752.593223] sdd: sdd1 [67964.907826] sdc: sdc1 [67974.038562] sdd: sdd1 [68595.107245] sdb: sdb1 [69525.179964] sdb: sdb1 [69835.958729] sdd: sdd1 [70766.572499] sdb: sdb1 [71076.828494] sdb: sdb1 [71377.605195] sdd: sdd1 [72298.301984] sdb: sdb1 [73219.937015] sdd: sdd1 [73637.287585] sdb…

My third Orange Pi Zero came last week, yesterday I plugged it and had heating issues... So I started reading, learning and testing.... Setup: OPiZ-1: 256 MB, no SPI flash - Has extension board plugged - for comparison OPiZ-2: 512 MB, with SPI flash OPiZ-3: 256 MB, with SPI flash (new one with problem) Test conditions: All with (newish) Sandisk Ultra 16 GB Class 10 All new formatted (SD Formatter) and burned/validated (Etcher v1.0.0) with Armbian_5.25_Orangepizero_Debian_jessie_default_3.4.113.img All on my desk - side by side, ambient temperature 25.0-25.1 C (20 cm from boards, no air flow) No case, no pass…

Hi! I have ARMBIAN 5.31 on my Banana Pi m1 and need some help. Early I used wheezy and mount webdav disk with davfs2 in fstab, but after I installed jessie fstab dont mount any davfs2 disk. Besides I have another problem: I use davfs2 to backup some video and photos to cloud storage throw webdav, and I have mistakes on large files (files much bigger then free space in /var/cache). Davfs2 send files in cache folder first (/var/cache/davfs2 by default) and then to webdav disk, so I have to use another disk with enough free space (sda1 in my case). When I was on wheezy I just point cache dir to sda in dafs2.config (cache_dir option) and all be OK, but i…

Hey all I'm trying to get an Orange Pi Zero (256MB) to talk with an MPU6050. (ARMBIAN 5.31 stable Ubuntu 16.04.2 LTS 3.4.113-sun8i) I've installed i2c. When I have a little OLED screen attached I get: root@orangepizero:~# sudo i2cdetect -y 0 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- 3c -- -- -- 40: -- -- -- -- -- -- -- -- UU -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 60: -- -- -- -- -- -- -- -- …

Hi, i have a Olimex Olinuxino-micro-emmc and the armbian image 5.31 and 5.25 booting fine but NO network is comming up. The link led's are on but no once Packet will be transmitted. The same board with my own u-boot/kernel version has no problems with network device. is it a bug or a feature? Best regards Mike

Edit: Please see my second post in this thread. I think I've identified exactly what my problem is, please see my second post in the thread. I need to change the display mode to something that my own TV is able to display. But no matter what I've tried, I haven't been able to change the display mode. How do you do it? ---- Hello, I just got an Orange Pi PC. I installed using the Armbian_5.32.170629_Orangepipc_Ubuntu_xenial_dev_4.11.7.7z image. I'm able to log in through SSH, and I've installed all updates (apt-get update && apt-get upgrade) I have the Orange Pi PC connected to my HDMI television. The scre…

I'm wanting to connect a Raspberry Pi Zero to my NanoPi Duo via USB Ethernet OTG. Has anyone gotten this to work? I've been following instructions posted at different sites (here's one - https://dev.webonomic.nl/connecting-to-a-raspberry-pi-zero-with-just-an-usb-cable-i) and I can get it to work via my desktop (with Debian) and a Raspberry Pi Zero and between RPI3 and RPI0, but can't seem to get it to work between NanoPi Duo and RPI0. Of course, I don't have a desktop on the NanoPi Duo, so everything has to be done via command line.

I am having some difficulty producing audio on an orangepi zero using the images listed here: https://www.armbian.com/orange-pi-zero/ No matter what I do, I cannot get any audio devices to show up in /proc/asound/cards There are a number of posts on here that suggest that audio doesn't work on version 4.x kernels. Is this still the case? And if so, where can I download an armbian image that does support audio?

It seems I have to install either of them for my chromecast to play nice. I have no prior experience with neither of them nor do I know which one is better. There are various threads on the internet but would be interested which one the community uses / trusts, cause I am a bit hesitant on adding random repos. My use case: Stream mkv on local with subs or transcode if it can't show subs. Board: Orange Pi Pc OS: Debian Stretch on 4.14.18 Would appreciate any feedback even if it's only a link to your preferred software / guide.

Dear Armbian friends, I have question about add DS18B20 temp sensor at RPi-Monitor (web based interface). Can somebody paste working config of this sensor? On internet I found many tutorials but with DHT sensors. On this page (Xavier is an author of RPi-Monitor I think) is described DS18B20 but in status "Working in progress". I tried this but without luck. https://xavierberger.github.io/RPi-Monitor-docs/32_sensors.html?highlight=ds18b20 Cheers, Lucas

Hi, I'm running the following kernel on my Orange Pi Lite: Linux lights 5.3.9-sunxi #19.11.3 SMP Mon Nov 18 18:49:43 CET 2019 armv7l GNU/Linux I'm getting the following crash in the WiFi driver (copy-pasted from dmesg) after some time (about 10 hours if I read the output correctly?). [36792.103947] ------------[ cut here ]------------ [36792.104326] WARNING: CPU: 3 PID: 1108 at drivers/net/wireless/realtek/rtl8189fs/core/rtw_mlme.c:2622 rtw_stadel_event_callback+0x41/0x1fa [8189fs] [36792.104331] Modules linked in: snd_soc_hdmi_codec snd_soc_simple_card snd_soc_simple_card_utils sun8i_codec_analog sun4i_i2s sunxi_cir sun8i_adda_pr_regmap snd_…

Hello, I'm trying to setup and access point with an orange pi zero. Note that the internal wifi card is not used and an 802.11 ac usb key is used. Hostapd boot up fine and mobile phone can connect to AP. Howover after few second the orange pi complety stop responding and the serial console loop with these message : [ 264.167603] unexpected IRQ trap at vector 00 [ 264.171871] unexpected IRQ trap at vector 00 [ 264.176140] unexpected IRQ trap at vector 00 [ 264.180409] unexpected IRQ trap at vector 00 [ 264.184678] unexpected IRQ trap at vector 00 [ 264.188946] unexpected IRQ trap at vector 00 Any …

As we know, the PCIe on H6 is buggy, which doesn't offer linear address, and Linux cannot support such kind of configuration. However, the Cortex-A53 cores used by H6 supports virtualization, which can be used to change the order of the address space. Recently, I tried to make use of virtualization to provide linear mapping of PCIe, and I succeed in making an Intel 6205 wireless card working. The hypervisor code is at https://github.com/Icenowy/aw-el2-barebone . It's intended to start before U-Boot, and located at 0x40010000. A U-Boot fork that is patched to load the hypervisor is at https://github.com/Icenowy/u-boot/tree/h6…

Hello, I'm using a Banana Pi P2-Zero based on H3 and I want to get Ethernet running. To no avail so far... When building the image, I use this parameters: BOARD=bananapim2zero BRANCH=current RELEASE=jammy BUILD_MINIMAL=no BUILD_DESKTOP=no I use the customize-image.sh script, but I don't change anything related to the drivers (or so I think). There are no patches, overlays or anything like that. I saw this topic but this solution doesn't help: I also tried something like this but it didn't help either: /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { target = <&emac>…

How to install Home Assistant Supervised on Armbian 23.02 Jammy (plus minus, but quite installed on the previous release of Armbian, this is based on Debian 10) Performed exclusively without a graphical interface, from the console. Works stably on Orange Pi Lite , including a connected Bluetooth dongle via USB and sensors to it. 1. The first installation of Armbian and the subsequent creation of a user and passwords, the next is required to install all updates via sudo apt update && sudo apt upgrade -y . Then you need to install the Firmware update through the armbian-config ->System utility as in the screenshot. Скрытый текст …

Under kernel 4.9, using a usb3.0 to Gigabit interface with RTL8153b card, the upstream and downstream speed can reach Gigabit. But with kernel5.10, the speed can't reach gigabit, and the driver file has been changed to the latest version, but still no effect. kernel5.10 Speed measurement root@orangepi3-lts:~# iperf3 -c 192.168.3.201 Connecting to host 192.168.3.201, port 5201 [ 5] local 192.168.3.146 port 44376 connected to 192.168.3.201 port 5201 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 24.8 MBytes 208 Mbits/sec 0 147 KBytes [ 5] 1.00-2.00 sec 23.5 MBytes 198 Mbits/sec 0 147 KBytes [ 5] 2.00-3.00 sec 23.5 MBytes 197 Mbit…

I disabled Armbian kernel upgrades to stay at Armbian 23.11.1 until Armbian 24 stabilizes. Yesterday I unfroze the kernel upgrades to upgrade to 24.2.1. I run: apt update apt upgrade apt dist-upgrade Apt update says All packages are up to date. shows nothing. What did I miss?

hello, thank you for your image for olimex A10 it's perfect on sd card but i want put in the sata drive i start command ./nand-sata-install and when finish , reboot but reboot , reboot , reboot , etc.... i not understand can you help , thank you

where did tunl0 come from ? is it there by default or .... may be I must dig in my history ? root@orangepione:/etc/network $ ifconfig -a eth0 Link encap:Ethernet HWaddr 6a:xx:xx:xx:xx:xx (** edited) inet addr:192.168.100.3 Bcast:192.168.100.255 Mask:255.255.255.0 inet6 addr: fe80::68f2:91ff:fef0:4579/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:35677 errors:0 dropped:0 overruns:0 frame:0 TX packets:22173 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3139622 (2.9 MiB) TX bytes:13744564 (13.1 MiB) Interrupt:114 lo …

Verify kernel 4.6 with dev on test construction Armbian where the CPU is not recognized correctly. root@orangepipc:~# lscpu Architecture: armv7l Byte Order: Little Endian CPU(s): 4 On-line CPU(s) list: 0 Off-line CPU(s) list: 1-3 Thread(s) per core: 1 Core(s) per socket: 1 Socket(s): 1 Model name: ARMv7 Processor rev 5 (v7l) [ 0.001455] CPU: Testing write buffer coherency: ok [ 0.001769] /cpus/cpu@0 missing clock-frequency property [ 0.001784] /cpus/cpu@1 missing clock-frequency property [ 0.001794] /cpus/cpu@2 missing clock-frequency property [ 0.001805] /cpus/cpu@3 missing clock-frequenc…

Hello, Can i use a 8TB hdd with orange pi plus 2? Is there any hardware / sotfware limitation, or i do something wrong? Armbian sees only 1.40 TB of 8 TB. I started from: https://www.armbian.com/orange-pi-plus-2and downloaded the jessie server. root@orangepiplus:~# uname -a Linux orangepiplus 3.4.112-sun8i #10 SMP PREEMPT Sun Oct 23 16:06:55 CEST 2016 armv7l GNU/Linux root@orangepiplus:~# dmesg |grep "sda\|scsi" [ 1.293990] scsi0 : usb-storage 3-1:1.0 [ 2.293196] scsi 0:0:0:0: Direct-Access ST8000AS 0002-1NA17Z 0009 PQ: 0 ANSI: 0 [ 2.295330] sd 0:0:0:0: [sda] 2743151276 512-byte logical blocks: (1.40 TB/1.27 TiB) [ 2.296410] sd 0…

Hi. Not so far downloaded the latest available isos for Orange Pi (the very first version) - usb not working - for example for Logitech wireless keyboard or mouse. In the past I've already reported this problem - there was fix. Is it possible to fix again? PS Why there is no separete image for Orange Pi? Why banana pi image? Thanks in advance.

Hi! Banana pi m1, armbian Ubuntu Xenial Legacy 3.4.113, bluetooth usb dongle. I can find bananapi from other devices, but can`t pair whit any device. journalctl -u bluetooth ar 15 16:05:11 bananapi systemd[1]: Starting Bluetooth service... Mar 15 16:05:11 bananapi bluetoothd[646]: Bluetooth daemon 5.37 Mar 15 16:05:11 bananapi bluetoothd[646]: Starting SDP server Mar 15 16:05:11 bananapi systemd[1]: Started Bluetooth service. Mar 15 16:05:11 bananapi bluetoothd[646]: Bluetooth management interface 1.0 initialized Mar 15 16:05:11 bananapi bluetoothd[646]: Failed to obtain handles for "Service Changed" characteristic Mar 15 16:05:11 bananapi bluetoothd[646]: Not e…

Hi! Thanks for your great job. I compiled Armbian_5.32_Orangepizeroplus2-h5_Debian_stretch_dev_4.13.0.img with your building script from git, which included last kernel with Orange Pi zero+ H5 support. Pluged uart-adapter for control booting process. U-Boot SPL 2017.09-rc4-armbian (Sep 05 2017 - 11:03:34) DRAM: 512 MiB Trying to boot from MMC1 NOTICE: BL3-1: Running on H5 (1718) in SRAM A2 (@0x44000) NOTICE: Configuring SPC Controller NOTICE: BL3-1: v1.0(debug):aa75c8d NOTICE: BL3-1: Built : 11:03:29, Sep 5 2017 INFO: BL3-1: Initializing runtime services INFO: BL3-1: Preparing for EL3 exit to normal world INFO: BL3-1: Next image address: 0x4…

Hello, I know one should't ask or complain here regarding the dev kernel branch, but maybe somebody of you stumbled upon this and knows where to point me: I successfully build and used the "dev" kernel several times for the BananaPi (Allwinner A20 Soc) and it works just fine. The patch regarding the axp209 sysfs interface can simply be taken over from the from the "next" kernel branch and you get a working temperture reading from the axp209 pmu. I still haven't managed to get the internal soc's temperature sensor working in dev kernel, though. I know it has something to do with the touchscreen driver but couldn't find out what exactly is required to make it…

Hi, please describe in detail the process of building your own kernel and modules on Debian/Ubuntu Orange Pi Zero/R1 (Allwinner H2+) ver. 3.4.113-sun8i (armv7l): http://www.orangepi.org/OrangePiR1/ and Orange Pi Zero Expansion Interface board I'm interested in modules: bonding, usbnet, cdc_ether, usbip I will be very grateful for your detailed answer

hi, i've been trying to get the SC16IS752/I2C UARTs working on opi-zero using DT Overlays. Here is my .dts: /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h2", "allwinner,sun8i-h3"; fragment@0 { target = <&i2c0>; __overlay__ { #address-cells = <1>; #size-cells = <0>; status = "okay"; sc16is752: sc16is752@4D { compatible = "nxp,sc16is752"; reg = <0x4D>; clocks = <&sc16is752_clk>; interrupt-parent = <&pio&…

Hello, I am trying to use g_serial but it does not work. I'm using fresh install of armbian (Armbian_5.38_Orangepilite_Debian_stretch_next_4.14.14.7z), with apt-get update/apt-get upgrade/armbianconfig Install headers. Linux orangepilite 4.14.15-sunxi #28 SMP Mon Jan 29 07:24:48 CET 2018 armv7l GNU/Linux This is the overlay I use to enable OTG: sudo /usr/sbin/armbian-add-overlay usbotg.dts /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { target = <&usb_otg>; __overlay__ { dr_mode = "otg"; status = "okay"; }; }; }; After rebooting OPi there are several erro…

I've just downloaded the Debian-server mainline image for my Olinuxino A20 Micro (Armbian_5.38 etc) and tried, without success, to change the video output from the default HDMI to the VGA one. Following the documentation (https://docs.armbian.com/Hardware_Allwinner/) I modified the boot.cmd file adding the lines: setenv video-mode sunxi:monitor=vga,hpd=0,edid=0 saveenv and recompiling it but the video continues to be enabled on the HDMI output, also after 2 (and more) restart. I noticed that in the boot splash screen a "Err: VGA" is reported. It's not too clear from the documentation if this setting can be applied also modifying the armbianEnv.txt …

Hi, I'd like to keep the features provided in AX but have my OPi Lite starting and running some software that communicates with a webserver periodically over the internet without the monitor, keyboard and mouse connected unless performing maintenance where remote access isn't appropriate. Is this possible or am I looking at an Armbian Bionic (unsupported) installation?

Hi, I tried to add the mcp251x overlay for Nanopi-NEO-Plus2 (Allwinner H5) using armbian-add-overlay command but got the error below. Does anybody know why? Below, you can find the dts file. Any help would be appreciated. Compiling the overlay dtc: livetree.c:521: get_node_by_phandle: Assertion `(phandle != 0) && (phandle != -1)' failed. /usr/sbin/armbian-add-overlay: line 76: 2078 Aborted dtc -@ -q -I dts -O dtb -o ${temp_dir}/${fname}.dtbo $1 Error compiling the overlay spi-mcp251x.dts /dts-v1/; /plugin/; / { compatible = "allwinner,sun4i-a10", "allwinner,sun7i-a20", "allwinner,sun8i-h3", "allwinner,sun50i-a64", "allwinner,sun50i-h5";…

Hello, I have a question about HDMI CEC in Armbian Stretch, is it possible to run this? After command lsmod I have module hdmi_hw_cec, I install libcec and cec-utils packages but cec-client still show "not devices". I read in sunxi wiki http://linux-sunxi.org/Linux_mainlining_effort#Status_Matrix that HDMI CEC should be active in revision 4.17, so when we can expect this version? :)

Hi, I’m curious how to boot into command line rather than the GUI desktop when booting up. I have looked at some other answers where changing the `nodm` but that file does not exist. Thanks!

TRYING TO create an ad-hoc network using wireless adapter( lb-link model: wn155a) on NANOPI NEO (Linux nanopim1 3.4.113-sun8i #28 SMP PREEMPT Thu Feb 2 02:01:28 CET 2017 armv7l GNU/Linux). we used this link https://citricks.net/create-access-point-linux/ BUT ad-hoc WAS NOT CREATED. running iwconfig looks like: lo no wireless extensions. tunl0 no wireless extensions. ra0 Ralink STA ESSID:"11n-AP" Nickname:"MT7601STA" Mode:Auto Frequency=2.412 GHz Access Point: Not-Associated Bit Rate:1 Mb/s RTS thr:off Fragment thr:off Encryption key:off …

I've been happily running orangepipc with armbian (buster, 4.19.62-sunxi) as an openvpn gateway for my home devices for some time. Here are some details: I have a remote openvpn server the pi runs an openvpn client and connects to the server the pi has ipv4 packets forwarding enabled my wifi router provides the pi's ip as the default gateway via dhcp So when I connect to wifi with my phone, all phone traffic will be routed through the remote openvpn server without need to install the openvpn client on the phone itself. With this setup the pi can easily saturate my 30mbit cable connection when downloading torrents for e…

Hello, I have problem with "Orange Pi Zero Plus" and functionality of Relay module (electrical circuit= normally closed). Relay module is attached on pin/port number "0". When I set up pin number "0" from "OFF" to "OUT" state with command: gpio export 0 out state is changed from OFF to OUT and parameter in column "V" is "0". It should mean that relay stays turned of. +------+-----+----------+------+---+ | GPIO | wPi | Name | Mode | V | +------+-----+----------+------+---+ | 12 | 0 | SDA.0 | OUT | 0 | Problem is, that relay immediately after execution of mentioned command enables(turns on) output electrical circuit. Relay m…

Hi, I have recently installed the latest Bionic on my Teres laptop. Unfortunately all the desktop elements are invisible: no icons or panels. Here is a photo: https://skyportal.xyz/_AUx7VZt6n2vp_QPu4LG4uLpafQMTK37xTFclUaK7rszfA

My 2 zeropi cards get new mac addresses at each reboot which is quite annoying for DHCP configuration If I rollback to 5.4.30 kernel the issue disappears. When using this kernel I get a 02:81 address for the two cards. When using current kernel the mac address seems totally random

hi i try to load bootlog from /boot/mmc on orange pi lite when add bootlogo=true to armbianEnv only armbian logo show. i check u-boot and it send an erro "Unknown command 'bmp' - try 'help'" i check u-boot env and u-boot dont have bmp command. ow can I fix this.

Hello, does this USB WiFi card work with armbian on Orange Pi 3 LTS? TP-Link Nano AC600 USB Wifi Adapter https://www.amazon.com/dp/B07PB1X4CN/ Does it need any drivers to be installed? If yes, is there any that is working with OPi 3 LTS? Btw I want to use this wifi adapter, because Armbian doesn't work with internal wifi card in this SBC - https://forum.armbian.com/topic/23505-orange-pi-3-lts-no-wifi/ (and sadly Devs didn't release a fix for it)

Attention, whatever you do next is at your own risk! Fixed dts overlay file for Armbian 23.02.2 (attached). 1. Now the system can fall asleep and wake up by a timer (without an external RTC, provided that it is powered) or by pressing a button - while wifi connects itself (if there is an automatic connection) and the system continues to work as if nothing had happened without unnecessary loading. 2. As a bonus, I added an indication of reading from a flash card as a red LED (this can be turned off). 3. I also activated the host on the micro-usb connector - now you can connect something else via the otg adapter as a third USB connector. To apply t…

Hi, guys. I'm using the last Armbian Cubieboard image (Armbian_23.11.1_Cubieboard_bookworm_current_6.1.63.img.xz) on my "Gemei G9" Allwinner A10 tablet. But via serial/UART the boot process stuck forever in "Starting kernel ...". Any tips on how to get the kernel to start? Thanks in advance Here is my boot log: U-Boot SPL 2023.10-armbian (Oct 13 2023 - 22:19:41 +0000) DRAM: 1024 MiB CPU: 1008000000Hz, AXI/AHB/APB: 3/2/2 Trying to boot from MMC1 ns16550_serial serial@1c28000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19 U-Boot 2023.10-armbian (Oct 13 2023 - 22:19:41 +0000) Allwinner Technology CPU: Allwinner A10 (SUN4I) Model: Cubietech…

When testing my most recent builds using the Armbian build framework I found that I was experiencing a constant load greater than 1.00. At first, I thought this is probably normal to have a load during the system boot but after waiting over 10 minutes I found that the load did not decrease. Firstly, I used HTOP but could not find a process that was heavy utilising the CPU with the relative CPU usage show as low. Next I tried using TOP which revealed a process called kworker: freezeable_power. Trying to search for the issue I did not find much until I came across this old forum post that described the same issues I was having: https://forum.armbian.com/topic/75…

I have recently been trying to get my spi ili9341 working under kernel 6.6, having gotten it working previously. I checked to ensure there were no changes in the overlay required by the newer kernel. I confirmed that the pins were configured correctly and that the ILI9341 DRM module had loaded.. Despite this I was met with a white screen. Think I must have missed something I swapped out my SD card for another using an image based on kernel 5.15.88, where I was able to recieve a display. Looking back over the dmesg log, I noticed a slight difference in behaviour with the older kernel. firstly we can clearly see that the SPI driver is requesting to use gpio 34 as…

Hello! I have installed Igors Debian Wheezy Kernel 3.4.108 image on SD-Card for my BananaPi Pro. All is fine, thanks Igor! (after changing to Sandisk) But I can't activate the onboard Wifi-module. sudo modprobe ap6210 brings error: FATAL: Module ap6210 not found I tried a lot of thinks, but no result: root@bananapi:~# lsmod Module Size Used by cpufreq_userspace 3524 0 bnep 14462 2 bluetooth 264185 7 bnep brcmfmac 96909 0 brcmutil 4800 1 brcmfmac spidev 6366 0 I can activate the Lemaker 5'' touchscreen an the I2S-Audio in the script.bin-file, but no Wifi…

Hello. I'm having trouble with infrared receiver. Whether the sunxi_cir driver installed in kernel or not, there is nothing in /dev/input except "event0", which is the power controller. Dmesg doesn't show anything neither. Version: Armbian 4.5 Lamobo-r1 Debian jessie next (unofficial), kernel 4.2.3. IR support was declared on download web page, so I decided to get vanilla kernel. That's because I had already tried Bananian with 3.18 kernel, and there were huge problems with kernel ppp (up to freezes of whole device). Has anybody encountered this problem?

Hi Guys, sorry if its a stupid question I have edited the script.fex in the boot folder and enabled the extra uart ports on the board. #dmesg | grep uart [ 0.676838] [uart]: used uart info.: 0x3f [ 0.681530] [uart]: serial probe 0 irq 33 mapbase 0x01c28000 [ 0.707837] sunxi-uart.0: ttyS0 at MMIO 0x1c28000 (irq = 33) is a U6_16550A [ 0.712720] [uart]: serial probe 1 irq 34 mapbase 0x01c28400 [ 0.738944] sunxi-uart.1: ttyS1 at MMIO 0x1c28400 (irq = 34) is a U6_16550A [ 0.743804] [uart]: serial probe 2 irq 35 mapbase 0x01c28800 [ 0.770000] sunxi-uart.2: ttyS2 at MMIO 0x1c28800 (irq = 35) is a U6_16550A [ 0.774874] [uart]: serial pro…

I have a orange pi pc (H3). I connected a thermal printer which has a TTL interface so I connected the TX wire from the printer to 8 and RX to 10 to orange pi. I change the serial port in my script to /dev/ttyS0 and tried a test print but it will not print. I have tried this in raspberry pi 2 and it works. Any tips how to connect the thermal printer to orange pi.

Hi, I bought about a year ago an orange pi plus. Just a few weeks ago, i tryed the new distro's I love to have debian on the board. And like your distro verry much. I have 2 problems: 1) If i download the file for orangepiplus, the board does nothing. No leds go on, no grafics on screen, nothing I also tryed at home compiling it myself. The result is the same nothing. My Orange Pi Plus has an H3 processor - it is one of the first OrangePi Plus boards. (Is this an error in your piplus distro - just because loborus for piplus works) 2) If i download the orangepih3 file, the board will startup. I can not run sata-nand, because i get an error - abo…

Greeting, I installed the OrangePI plus image (desktop) on my Orange PI plus2. It seems to work fine but I can't get any video output. I tested with several h3disp settings, with a HDMI to VGA adapter then with an HDMI to DVI adapter, and finally on the A/V port. I have no hdmi screen to test direct connection without adapters. Ideally I would like to use the HDMI to VGA adapter. any ideas ?

Hello guys, I am new to this forum and this is my first thread. I bought a Nanopi M1 and try to play with the GPIO. I follow all the official instruction and install MatrixGPIO-python However, after the installing, I would like to test the GPIO with script that come with the Git Clone The terminal shows me this response "Fail to set gpio direction" Does anyone know how to solve this problem? Thank you

Hi Friends, on Banian I was using "xset dmps force off" and "xset dpms force on" to switch display off and on as I need it. Tryed to use this commands in terminal with armbian but nothing happens. I'm using LeMakers 5" LCD RGB Display with PCAP Touch. Armbian is 5.24 jessi with desktop and 4.8.12 Kernel. Has anyone an Idea, how to turn off and on display form terminal? Yours, Martin

Hello Guys, I want to use airodump-ng (Aircrack-ng Suite) or Kismet to get all WiFi Clients in the area. For that, I would like to use the internal WiFi Chipset (so I don't have to use an external WiFi Dongle). My problem is, after I enable the monitor mode (with iwconfig and/or airmon-ng), which gives me no error and it says, the monitor mode is enabled, I am getting no results with Airodump-ng nor Kismet. Are there any solutions for this problem? Is is the driver not capeable of using monitor mode? Thanks in advance, KittFanNr1

I'm trying to get my MAC address on my orangepi-one to be what it used to be before the upgrade to "ARMBIAN 5.27 stable Debian GNU/Linux 8 (jessie) 4.10.11-sun8i" but I'm having dificulty I tried decompiling /boot/dtb/sun8i-h3-orangepi-one.dtb and adding mac-address = [52 53 3d 80 aa 0c]; few other tries, then tried mac-address = <0x52 0x53 0x3d 0x80 0xaa 0x0c>; in the ethernet@1c30000 { section: latest version looks like: ethernet@1c30000 { compatible = "allwinner,sun8i-h3-emac"; syscon = <0x20>; …

Hello world, this is my first visit in this forum and my first question, please don`t bite me, if somethings wrong (and sorry for my bad englisch too, I`m from germany, blackwood forrest....). I am using my cubietruck now since may 2014, everythings ok. Now i got a week holiday and i thougt about an update for my cubietruck, it`s not about the ubuntu 14.04, it`s more about my old 4 GB SD-Card. OK, 10 EUR and i got an new 16GB Card "up to 80 MB/Sec." which i dont believe, but the problem is at another place: + first writing the image to the new 16 GB card: https://dl.armbian.com/cubietruck/Debian_jessie_next.7z + next backup the old…

I got AT070TN90 display and I am trying to get 800x480 resolution on it. root@orangepipcplus:~# uname -a Linux orangepipcplus 4.11.5-sun8i #11 SMP Fri Jun 23 20:03:23 CEST 2017 armv7l GNU/Linux trying "h3disp -m 800x480" and "h3disp -m 31" does not give any results , it is working on -m 32 but everything is too small .... than I tried to edit script file , but with no success any ideas ?

Looking to use this in a production assembly (months away...) While testing, have found that g_multi does not work. g_serial and g_mass_storage work fine... How do we get this added to the list of items to be fixed?

When 40pin female-female cable connected to my Orange Pi Plus 2 GPIO voltage on pin1 decreasing from 3.3v to ~ 1.6v WAIDW? Spoiler

OrangePi PC H3 UsbTV kernel driver causes complete system freeze on Armbian OrangePi PC kernel 4.14. Did anyone observed similar issues? I already reported a bug against the USBTV repo, but not sure if this is the right place. [Update: After quick response of Federico Simoncelli from the USBTV repo, I reported this bug to the kernel bugzilla as a new bug there] On x86_64 platform it works well. Is it the bug of Armbian or USBTV?