Allwinner sunxi

Tried both Debian and Ubuntu based 23.5 releases on my v1.4 board Boot process stops at "Starting kernel..." Also tried the "minimal CLI" debian release with same results. The previous versions 23.02 are fine. ▒ U-Boot SPL 2022.07-armbian (May 27 2023 - 19:26:49 +0000) DRAM: 512 MiB Trying to boot from MMC1 U-Boot 2022.07-armbian (May 27 2023 - 19:26:49 +0000) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi Zero DRAM: 512 MiB Core: 65 devices, 17 uclasses, devicetree: separate WDT: Not starting watchdog@1c20ca0 MMC: mmc@1c0f000: 0, mmc@1c10000: 1 Loading Environment from FAT... Unable to use mmc 0:1.…

I've tried many permutations of overlays and user-overlays and I can get /dev/spidev0.0 or /dev/spidev0.1 to be present, but I can't seem to get both simultaneously. I need both to migrate a project from an older Fedora distribution relying on modprobe to the latest version of Armbian. Any suggestions will be greatly appreciated! I started with very recent Armbian 23.02 Bullseye XFCE downloaded from arbian.com/banana-pi-plus .. Armbian_23.02.2_Bananapi_bullseye_current_5.15.93_xfce_desktop.img and I added the following to the /boot/armbianEnv.txt file, as described in the Armbian page associated with the BananaPi M1+ .. f…

Hi, I finally have time to get back to my little project. I've been trying to get a working display with tinydrm for an ILI9341 base lcd. My setup works on OpenWrt with the older fbtft driver, but now I'd like to go back and try Armbian (current release is Jammy) on it. My first try with devicetree overlay seems functional but not correct. The display just show garbled data (see attached). What could be the problem with it? This is my env. verbosity=1 bootlogo=false console=both overlay_prefix=sun50i-h5 overlays=usbhost1 usbhost2 spi-spidev param_spidev_spi_bus=0 rootdev=UUID=e0ed80c4-a252-4d96-ad61-78b7834d6b8d rootfstype=ext4 user_ov…

Thought this might be useful: FROM: http://www.orangepi.org/orangepibbsen/forum.php?mod=viewthread&tid=2236 01 3.3V 02 5V 03 TWI0-SDA PA12 04 5V 05 TWI0-SCK PA11 06 GND 07 PWM1 PA06 08 UART1_TX PG06 09 GND 10 UART1_RX PG07 11 UART2_RX PA01 12 SIM_CLK/PA_EINT7 PA07 13 UART2_TX PA00 14 GND 15 UART2_CTS PA03 16 TWI1-SDA PA19 17 3.3V 18 TWI1-SCK PA18 19 SPI1_MOSI PA15 …

When starting orange pi, it happens that not all the RAM is available. That is, the orange pi has 2 GB of RAM and it is written that there is only 1 GB of RAM. This often happens when restarting using the reboot command. If you turn off the power and reconnect, this problem appears much less often. When 2 gb is available: https://paste.armbian.com/asatebupuw When 1 gb is available: https://paste.armbian.com/bohapeyahi Скрытый текст Скрытый текст

Hi, I need a help. I have waveshare 4inc lcd touch play display but I don’t know how to enable touch play. Please Help me.

The problem seems to be kernel version 6.1.30; Just writing image file 'Armbian_23.5.1_Nanopineo_bookworm_current_6.1.30_minimal.img' to SD-card gives the following output via serial console: U-Boot SPL 2022.04-armbian (May 27 2023 - 19:27:28 +0000) DRAM: 512 MiB Trying to boot from MMC1 U-Boot 2022.04-armbian (May 27 2023 - 19:27:28 +0000) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: FriendlyARM NanoPi NEO DRAM: 512 MiB Core: 33 devices, 12 uclasses, devicetree: separate WDT: Not starting watchdog@1c20ca0 MMC: mmc@1c0f000: 0, mmc@1c11000: 1 Loading Environment from FAT... Unable to use mmc 0:1... In: serial Out: serial Err: seria…

Hi Team I have two brand new Orange PI Zero LTS. Is this supported with the normal Zero download? Thanks

I have Orange Pi Plus 2 running Ubuntu Bionic with Armbian Linux 4.19.62-sunxi and I would like to upgrade it to recent Armbian build based on Ubuntu Linux Server and move OS to SSD connected to one of USB ports. I tried to use Armbian_22.08.2_Orangepiplus_jammy_current_5.15.69.img.xz but it does not connect to both HDMI and network. I tried unofficial command line interface images from product page and weekly released unsupported community builds. Behavior of all these builds is the same - no output to HDMI, no network connection. Finaly I found that recent image for Orange Pi Plus / Plus 2 which boots is Armbian_22.08.1_Orangepiplus_jammy_current_5.15.63.img.xz.…

http://paste.armbian.com/icedujiguw.yaml Hello everyone, trying to give new life to this old Orange Pi+ 2. Here is described what hapens when i try to boot up latest image. Can anyone help. Thanks in advance. Armbian 23.8 Bookworm Kernel 6.2.y, Size: 421Mb, Release date: Jun 3, 2023 SBC gets stuck after the request Sense .. and doesnt booy up, if i plug a device in usb ports, it bootloops .. see below using same sd-card and a diffrent image file works with no issues . hardware : grounded out pin 9 of the SD card slot (checked with multimeter and works) U-Boot SPL 2022.07-armbian (Jun 03 2023 - 19:37:25 +0…

Attention, whatever you do next is at your own risk! Fixed dts overlay file for Armbian 23.02.2 (attached). 1. Now the system can fall asleep and wake up by a timer (without an external RTC, provided that it is powered) or by pressing a button - while wifi connects itself (if there is an automatic connection) and the system continues to work as if nothing had happened without unnecessary loading. 2. As a bonus, I added an indication of reading from a flash card as a red LED (this can be turned off). 3. I also activated the host on the micro-usb connector - now you can connect something else via the otg adapter as a third USB connector. To apply t…

Hi! I am trying to use Armbian 23.5 Jammy XFCE for new Orange Pi Zero Plus 2. I have TTL-USB connection through Serial port. In pyutty window i see log U-Boot SPL 2022.07-armbian (May 27 2023 - 19:28:04 +0000) DRAM: 512 MiB Trying to boot from MMC1 U-Boot 2022.07-armbian (May 27 2023 - 19:28:04 +0000) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Xunlong Orange Pi Zero Plus 2 DRAM: 512 MiB Core: 65 devices, 18 uclasses, devicetree: separate WDT: Not starting watchdog@1c20ca0 MMC: mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c11000: 1 Loading Environment from FAT... Unable to use mmc 0:1... In: serial Out: serial Err: serial Net: …

Hi gang. I am having a consistent problem changing the board over boot from the SD with the system on any kind of USB attached drive. The drive I want to put it on is a 1t ssb, which otherwise formats fine, over and over again, burns images on it fine (though rpi doesn't like how much power it grabs). But I duplicated the problem with a formatted SD card in a reader in the USB port as well. The same error message appeared. Now I have to say that I have read this post here: to see if there was anything unique to the H3 to accomplish this, but Igor said there to just follow the simple directions at Getting Started, which though dated, still work close…

Hi! I have banana pro, 5.15.93-sunxi #23.02.2 (bullseye), and use internal wifi adapter as a wifi client. The medium btw my client and ap is instable, there are frequent rate changes (6Mbps...54Mbps), so in order to get rid of it I need to set mandatory wifi rate no more than 6 Mbps. Give me the hint, please: 1. To set wifi rate strictly to 6 Mbps. I had tried iwconfig wlan0 rate 6M - I got "Error for wireless request "Set Bit Rate" (8B20) : SET failed on device wlan0 ; Operation not supported." . 2. To adjust 802.11n parameters (rate, number of spatial streams and so on). Thank you in advance, Aleksei

Hi all, I try to use SPI on the BananaPi M2 Berry. The devices are activated in the configfile and the devices spidev0,0 and spidev1.0 are shown in the /dev .directory but the spi-bus did not work. DMESG shows the following error - messages : [ 0.944871] sun6i-spi 1c05000.spi: Failed to request TX DMA channel [ 0.944893] sun6i-spi 1c05000.spi: Failed to request RX DMA channel [ 0.945987] sun6i-spi 1c06000.spi: Failed to request TX DMA channel [ 0.946006] sun6i-spi 1c06000.spi: Failed to request RX DMA channel OS version is 6.2.12-sunxi Any idea what's wrong ?

Hello! Brand new user here to the NanoPi Neo and even the forum. I'm planning to use a NanoPi Neo as hardware "interactor", the main idea is to connect a NanoPi Neo to a smartphone (Android or iOS), power the board from the USB cable and work in Host Mode to interact with de smartphone with libimobiledevice or adb. OTG does not support charging + data at the same time without a "special" OTG adapter. What I want to do is power the NanoPi by using the smartphone and even interact with it in host mode, like a regular computer will do, in simple terms, using a single cable, but getting power from it. Is this possible using NanoPi microUSB+OT…

Is there any way to get interrupts working on BPI M2 Berry/Ultra? I tried with raspbian and wiringPI/RPi.GPIO but there is a wait for support() “bug” which has been reported a while ago but no updates have been made in the thread. Currently Im running Armbian 22.11.00. If anyone has some experience or suggestion for a library/smth and is willing to share it that would be great. Thank you for your time.

Hello, I am trying to communicate using UART PORT. I have connected to 8, 10 and GND pin. Also I enabled UART3, but it doesn't work. Any solution? Thanks !! Enviado desde mi iPhone utilizando Tapatalk

Hi, Is it possible to remap the i2c1 to use the i2c0 default pins via armbianEnv,txt ?. What I want to achieve is to have the PD25 and PD26 to appear as bus 1. Thank you.

Hi, When I scan the I2C with i2cdetect, I get the following, without connecting any i2c device. May I know which device on the motherboard is taking up the three addresses. Thank you sudo i2cdetect -y 1 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: 30 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 50: 50 -- -- -- 54 -- -- -- -- -- -- -- -- -- -- -- 60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 70: -- -- -- -- -- -- -- -…

Hello everyone, Would like to ask for some guidance regarding how to install armbian on a t507 processor. as written here in this post allwinner 507 processor it says For this reason I have tried to burn an image for orangepi zero 2 but it doesn't boot, it just get frozen and I can't get any logs because the serial console do not prints anything all black. Does someone could maybe have some suggestion of what I could try? anything is more than welcome. Thank you in advance

Well it took me longer than i hoped but i have managed to forward port icenowys code for TVE on the H2+/H3 to mainline armbian. It seems to work totally fine, with a few caveats. First: Sample images of it in action -> https://imgur.com/a/vXQEM Second: the patch itself -> https://github.com/stevenj/h3-tve/tree/v0.0.11 Third a prebuilt image for Orange Pi Zero: -> https://github.com/stevenj/h3-tve/releases/tag/v0.0.11 Howto: just put the patch into userpatches for the sunxi-next kernel, and build. it should apply cleanly. Its for H2+/H3. I have only tried it on a orange pi zero, but it should work on all H2+/H3 boards. …

Neo has one SPI port and I need two, so would like to add another spi using spi-gpio, but no success (I think). I am using Armbian 23.02.2 Bullseye, default kernel does not enable it, recompiled using linux-source-5.15.93-sunxi.tar.xz, enabled spi-gpio as module. Digged around forum, prepared below dts and armbian-add-overlay succeeded. But there is no message arrived when loading (dmesg shows nothing about spi) and no /dev/spi* created. Is it OK or there must be something? Please advise.... / { compatible = "allwinner,sun8i-h3"; fragment@0 { target-path = "/"; __overlay__ { …

i have a tablet on Allwinner A20, I burned Armbian_23.5.0-trunk.134_Lime2_bookworm_edge_6.2.12_xfce_desktop.img.xz into sdcard, it looks like everything is okay, but the tablet work only via HDMI, how to enable the tablet display ?

I configured Armbian on a mSD card and decided to try and move it to the eMMC. I used the nand-sata-install utility, All files from the mSD card are copied, and the last step fails. I get Error: no u-boot package found, exiting Any pointers?

i am normal write the sd card by rufus, can boot into system, when i use armbian-config install system in emmc boot in emmc after copy i try shut down and remove the sd-card, boot fail, power led no on, how to fix, thanks

Just tried Armbian 23.5 Bookworm, cli & minimal. Both report the same in the console. Board works just fine with official img from www.friendlyelec.com Here is the terminal output.

Hello, I have installed the latest version of armbian on my Orange pi win and I have not been able to make the desktop appear, it always stays waiting for a command, I have done update and upgrade and nothing. Can somebody help me

Hi. Please help me to understand how hardware encoding works in nanopi with H3 chipset. I have newest version of armbianos: cedrus and related modules is loaded by kernel There are following hardware acceleration methods and encoders Please explain me what i am doing wrong here : and here: Thanks a lot.

Hi. I want to install RTL8188fu on this orange pi pc but I have no luck. Bus 003 Device 005: ID 0bda:f179 Realtek Semiconductor Corp. RTL8188FTV 802.11b/g/n 1T1R 2.4G WLAN Adapter I'm using this repository https://github.com/kelebek333/rtl8188fu , but....: orangepipc:~:# sudo dkms install ./rtl8188fu Creating symlink /var/lib/dkms/rtl8188fu/1.0/source -> /usr/src/rtl8188fu-1.0 Error! Your kernel headers for kernel 5.15.93-sunxi cannot be found. Please install the linux-headers-5.15.93-sunxi package or use the --kernelsourcedir option to tell DKMS where it's located. sudo apt install linux-headers-$(uname -r) Reading package lists…

I can't set up gpio-poweroff feature described here. I tried made overlays from here and here - no effect. U-boot boots with no errors. Then i am tried to edit DT (armbian-config > System > Dtc), - manually add node at pinctrl@1c20800: Скрытый текст pwr_off_pins: pwr_off_pins { pins = "PA21"; function = "gpio_out"; }; and node at "/": Скрытый текст gpio-poweroff { compatible = "gpio-poweroff"; pinctrl-names = "default"; pinctrl-0 = <&pwr_off_pins>; gpios = <&pio 0 21 0>; }; …

Hi I have old orange pi A20 board with vga https://www.armbian.com/orangepi/ It armbian loads as expected, environmet file I added the fdt line. But after I reboot after command armbian-install after transfering files to the ssd hard drive it board does not start without errors. failed to mount media/mmcboot dependency failed for /boot dependency failed for local file systems <..> you are in emergency mode attached image of the error: imgbb_link

The system displays two WLANs, but in reality, there is only one onboard wireless network card. The network connection is slow and disconnected. The official system of Orangepi is normal, this issue occur in the new version of the Armbian system. logs：https://paste.armbian.com/eborebaviq

I'm a newbie. Got the NanoPi R1 that sports a UART but no Video Output. Now when I want to read the output of the serial console I need a 3-wire cable and a converter, that much I know. But what is the baud rate? Where is this configured on the armbian NanoPiR1 image (on my raspberry Pi I just checked and found the file /boot/cmdline.txt with that settings, in my case it's 115200) Why is the baud rate nowhere documented? On the download page https://www.armbian.com/nanopi-r1/ it is stated that "serial console is enabled on UART1, which is exposed on chasis" , but no hint about which speed to use. There neither is any info about the baud rate on…

raw_gadget compile failed make make -C /lib/modules/5.15.93-sunxi/build M=/root/raw-gadget-master/raw_gadget SUBDIRS=/root/raw-gadget-master/raw_gadget modules make[1]: Entering directory '/usr/src/linux-headers-5.15.93-sunxi' MODPOST /root/raw-gadget-master/raw_gadget/Module.symvers make[3]: *** No rule to make target '/root/raw-gadget-master/raw_gadget/raw_gadget.mod.o', needed by '/root/raw-gadget-master/raw_gadget/raw_gadget.ko'. Stop. make[2]: *** [scripts/Makefile.modpost:139: __modpost] Error 2 make[1]: *** [Makefile:1820: modules] Error 2 make[1]: Leaving directory '/usr/src/linux-headers-5.15.93-sunxi' I cat Module.sysmvers in /usr/src/linu…

Hi all! After upgrading to 6.1.24-sunxi64 on my Orange Pi 3 LTS I lost sound at the audio output. dmesg shows this: platform sound_ac200: deferred probe pending I am a newbie to linux - can you, please, provide me a hint how to install the sound card back or revert to the older kernel with a working sound? Thank you!

My third Orange Pi Zero came last week, yesterday I plugged it and had heating issues... So I started reading, learning and testing.... Setup: OPiZ-1: 256 MB, no SPI flash - Has extension board plugged - for comparison OPiZ-2: 512 MB, with SPI flash OPiZ-3: 256 MB, with SPI flash (new one with problem) Test conditions: All with (newish) Sandisk Ultra 16 GB Class 10 All new formatted (SD Formatter) and burned/validated (Etcher v1.0.0) with Armbian_5.25_Orangepizero_Debian_jessie_default_3.4.113.img All on my desk - side by side, ambient temperature 25.0-25.1 C (20 cm from boards, no air flow) No case, no pass…

Hello, Im trying to get 2 Uarts working on an Orange Pi Zero+2. Im using armbian Buster image for OPiZ+2 Linux orangepizeroplus2-h3 5.4.43-sunxi #20.05.2 SMP Mon Jun 1 18:26:22 CEST 2020 armv7l GNU/Linux I added UART1, UART2 and UART3 to armbianEnv.txt and was able to read / write on ttyS2 on pins 8 (PA00) and 10 (PA01). But couldnt find which pins ttyS1 or ttyS3 are on. I read at that UART 3 should be Tx PA13 Pin 24 Rx PA14 Pin 23 Is anyone able to suggest which pins I can use for a 2nd UART and is there a file I can look in to find the configuration for the UART Overlays ? Thanks Chris …

Good morning, I'm trying to activate PWM by hardware to use wiringpi. I activate the PWM option from Armbian config hardware, but it doesn't seem to have any effect, and UART0 doesn't seem to be deactivated. I'm not sure if there's any issue or if I'm doing something else wrong. The build is Armbian 22.11.1 Jammy with Linux 5.15.80-sunxi. Thanks for the help!

I've been reading on the forums on the possibility of having multiple OSes inside 1 EMMC for the Opi PC+. From what I understand, inside a typical EMMC installation, it has 3 partitions: 1) Bootloader partition, which runs first and starts the main partition 2) main partition, contains OS files 3) unallocated free space suppose I have 2 devices: 1. Armbian Jammy Server 2. Armbian Jammy Desktop Now I want to make another device that has 2 OS partitions, like so: 1) Bootloader 2) 1st OS main partition, 3) 2nd OS main partition, 4) unallocated free space I'm thinking of using DD to extract the …

I have an Orange Pi Mini 2. As far as i know there is no official/ unofficial armbian build for this. there are other boards like orange pi pc, orange pi 2 and tritium h3 board whose images run fine for this board. I have also made armbian image builds with orange pi pc as target and these images work on opi mini 2. I would like to know how could i make a build exclusively for orange pi mini 2.

Hello, I have a problem on my orange pi 3 lts. Namely, I have armbian 23.03 Jammy Xfce installed and on some screens it shows normally, on others the image does not appear. I also tried using the Uart converter and it loads everything normally, but then the following message starts appearing every second. [ 161.905394] panfrost 1800000.gpu: js fault, js=0, status=INSTR_INVALID_PC, head=0xa005bc0, tail=0xa005bc0

I have an Orange Pi PC Plus (Armbian Bullseye CLI) that I'm using as a NUT server connecting to a Cyberpower UPS. Every 30 minutes the driver stops working and upon further investigation, this looks to be a USB connection issue. Is there some power-saving mode that would cause this or any other known issue? Thanks!

kernel version Linux bananapim2plus 5.15.93-sunxi #23.02.2 SMP Fri Feb 17 23:49:46 UTC 2023 armv7l GNU/Linux dmesg [ 1065.023248] udc-core: couldn't find an available UDC or it's busy [ 1065.023290] misc raw-gadget: fail, usb_gadget_probe_driver returned -16 [ 1193.665509] udc-core: couldn't find an available UDC or it's busy [ 1193.665534] misc raw-gadget: fail, usb_gadget_probe_driver returned -16 [ 2883.115015] udc-core: couldn't find an available UDC or it's busy [ 2883.115040] misc raw-gadget: fail, usb_gadget_probe_driver returned -16 [ 2908.077549] udc-core: couldn't find an available UDC or it's busy [ 2908.077574] misc raw-gadg…

After running the armbian-install program and selecting option "1 'Boot from SD - system on SATA, USB or NVMe'" the program transfers the contents of the SD card to the drive (SATA or NVMe). And it works. The problem occurs after booting - a message appears about the device being unable to mount /media/mmcboot . And indeed - the contents of /media/mmcboot and /boot are empty. The problem turns out to be the contents of the /etc/fstab file generated on the SATA/NVMe drive. The mount point /media/mmcboot has a only UUID value, but the text "UUID=" is missing before the value. After manually adding it, everything starts fine. If someone could lean in and correct th…

Hi there 👋 I'm using a NanoPi Duo2 with Armbian 21.08.1 Bullseye and Linux jenkins-agent-arm32 5.15.93-sunxi #23.02.2 SMP Fri Feb 17 23:49:46 UTC 2023 armv7l GNU/Linux I want to use an SPI screen on it, but I don't know which library to use to handle the GPIO... I've tested quite a few and none of them seem to work. I have enabled SPI and I2C in `armbian-config` and `sudo i2cdetect -y 0` works (even if nothing is found), but what is the next step? sudo i2cdetect -y 0 [sudo] password for poddingue: 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- --…

I have good temps and was thinking to overclock it but have no idea how to do it.

Hello! My problem is with paying for OrangePi Plus 2 (not E), but I haven't found a suitable section. Dear administrators, please fix the split if I made a big mistake. I was installed image orangepiplus/Bullseye_current (Nov 30, 2022) in eMMC. All works is normal. In armbian-config I was run Firmware (Update all packages and firmware). Afeter this the board are not loading from eMMC or external CD with current image Armbian. The Ubuntu from site orangepi.org the loading is normal. In debug-uart I see a cyclical reboot with: <0xdd>!␊ ␊ <0xea><0xfc>q<0xb9><0xf6>Core: 65 devices, 18 uclasses, devicetree: …

Hi, I've got a pair of OrangePi 3 LTS boards running the CLI only install of Debian Bullseye with a kernel of 5.15.89-sunxi64 and all the latest updates applied. But when I run the 'top' command, I always see a load of 1.0 or higher. Even when the system is completely idle. I'm running the system of the eMMC, not SDcards. I realize that this is really more of a cosmetic issue, but I was hoping someone had a suggestion on how to fix it. The system is mostly idle, it's a test box or remote management system, so it's not really critical, and the load doesn't go high anyway. Cheers, John

Hello, I'm using a Banana Pi P2-Zero based on H3 and I want to get Ethernet running. To no avail so far... When building the image, I use this parameters: BOARD=bananapim2zero BRANCH=current RELEASE=jammy BUILD_MINIMAL=no BUILD_DESKTOP=no I use the customize-image.sh script, but I don't change anything related to the drivers (or so I think). There are no patches, overlays or anything like that. I saw this topic but this solution doesn't help: I also tried something like this but it didn't help either: /dts-v1/; /plugin/; / { compatible = "allwinner,sun8i-h3"; fragment@0 { target = <&emac>…

Hey, I recently decided to give the 22.11 a try on my M1, but I can't get my sata SSD to be the system root and boot again. 18.04 it worked for me with the exact same setup. I used this: https://docs.armbian.com/User-Guide_Getting-Started/#how-to-install-to-emmc-nand-sata-nvme-usb went with armbian-install only option for me was boot from SD and system on sata. But after the preparation of the ssd, the reboot always runs into emergency mode with not really good hints how to solve, or what even the issue is. Any tips or hints are welcomed.

Machine model: Banana Pi M2 Berry Linux bpi08 6.2.7-sunxi #3 SMP Fri Mar 17 07:58:04 UTC 2023 armv7l GNU/Linux (armbian@next) Mir ist es nicht möglich eine interne Temperatur auszulesen. Brauche dringend Hilfe! Der Link“/etc/armbianmonitor/datasources/soctemp “ exitiert zwar, nur die Datei / das Verzeichnis existiert nicht: nicht vorhanden → /sys/devices/virtual/thermal/thermal_zone0/temp nicht vorhanden → /sys/class/thermal/thermal_zone1/temp Wo soll diese Dateien überhaupt erstellt werden? Anmerkung Es wäre schön, wenn es für den Banana Pi M2 Berry eigene Tags geben würde. Er unterscheidet sich von dem Banana Pi M2+.

Armbianmonitor: I had use armbian-config to change the dts for change pin start status. it worked. but just work when kernel load. it don't effect the uboot. did i missing some step? or it's because my uboot is too old? Thanks, mika

Hey! I have Lime2-Server from olimex here and get no internet connection. I configured eth0 via nmtui and tried to activate it, but I get: "could not activate connection: the device could not be readied for configuration". Any idea or known issue? best regards armybee

How I solve this problem or is it an Ambrian bug? Maybe a better question is what is causing these repeated messages. I am at a loss to finding a solution. BOARD=bananapipro BOARD_NAME="Banana Pi Pro" BOARDFAMILY=sun7i Spoiler --< CUT >-- [ 50.900954] ieee80211 phy0: brcmf_fweh_call_event_handler: no interface object [ 50.900982] ieee80211 phy0: brcmf_fweh_event_worker: event handler failed (72) [ 50.976400] ieee80211 phy0: brcmf_fweh_call_event_handler: no interface object [ 50.976437] ieee80211 phy0: brcmf_fweh_event_worker: event handler failed (72) [ 51.025829] ieee80211 phy0: brcmf_fweh_ca…

Hello, after a poweroff command, the board Led switches off but the ethernet port Led still green blinks. The os has well performed the shutdown (I can see this through the UART). How is it possible? Thanks

I had successfully installed Armbian_2022.08.8_Bananapi_bullseye_CLI_5.15.74 on my M1 and copied the system to an SSD which I had attached to the SATA port. Then I had updated the UUID in armbianEnv.txt and running the system from SSD was working fine. The system was running headless in my closet for about 2 months, and I even had no problems to remotely restart the device until today, when it did not come back up after a reboot. I took it from the closed and hooked it to a monitor just to see the following error messages: ** Bad device specification mmc 0 ** Couldn't find partition mmc 0 I suspected a broken SD card but a check on my Ubuntu de…

So I got a new orange pi 3 lts and I have installed armbian bullseye on it, but I can't seem to make it work with my crt TV like my raspberry pi 3 b+, even though I am using the same cable and TV and it still works with my raspberry pi I have tried: -Changing the resolution -Changing the aspect ration But nothing works What am I supposed to do to make my armbian work on my CRT tv??

armbianmonitor output: http://ix.io/4qwA I assume it's crashing as I have no display connected to it. Every few days I just notice I can no longer reach the network folder, but it works after a power off/power on. Not much running on it, samba for file share and deluge for occasional downloads. I also recently run an update, upgrade and dist-upgrade, but it didn't help. I don't really know what should I look for in the log. OS: Armbian buster (21.02.1) armv7l Host: LeMaker Banana Pi Kernel: 5.15.93-sunxiC CPU: Allwinner sun7i (A20) Family (2) @ 960MHz

Hello everyone, I am new to the world of Orange Pi 3 LTS 1.4 and Armbian. I have very recently installed this os on my Orange, it turns out to work almost everything correctly except Wifi and bluetooth. It is really important for me to get Wifi working for various projects I have in mind and I find armbian very reliable and supported. When I try to connect the Network Manager interface returns: On the net I found various discussions about this but no real solution. Does this happen to you as well? It seems not to recognize the wifi chip. Below is the armbianmonitor: https://paste.armbian.com/iteheqokov …

Hello, I am trying to use my NanoPi neo Plus 2 rev 1.2 board as KVM with help of (kvmd-armbian) and USB-HDMI capture card and USB-A to USB-A cable as OTG for emulation of Keyboard and mouse as HID. I discoverred that If I install "Armbian 23.02 Jammy with Kernel 5.15.y" like the install script from srepac/kvmd-armbian recommends, updated it and installed the srepac/kvmd-armbian piKVM, it installed properly and it is working BUT to my OTG USB HID connection to work I had to convert sun50i-h5-nanopi-neo-plus2.dtb to sun50i-h5-nanopi-neo-plus2.dts and in there find "dr_mode" and change it to peripheral (or otg) to get my HID OTG input to work w…

Orange Pi Zero 512 MB has a serious wifi problem. After i connect the wifi network, i loose connection and i can't access my zero until i connect with ethernet cable. Interestingly, after i connect ethernet cable, wifi reconnects. i set up my wifi connection with nmtui. Auto connect enabled. I really need to solve this wifi issue. In my thinking there two options, which one is better i don't know. 1 st option: I have to buy wifi adaptor, but i don't know will it solve the problem. (and probably i am going to have driver problem) 2nd option: I am going to write a new thread with python. This code will check wifi connection every 10 seconds, if …

Hello there, I am beyond my expertise (that which is already limited) have found a guide. Now the guide uses ili9486 so it was substitute it will ili9341 as well as the build they used official build am using Armbian_22.11.1_Orangepi3-lts_bullseye_current_5.15.80 and int with a new one found in the fbtft library. I also need to translate for Russian with chrome not their are photos of it working but all I get is a white screen. here is my version of the overlay. /dts-v1/; /plugin/; / { compatible = "xunlong,orangepi-3-lts","allwinner,sun50i-h6"; fragment@0 { target-path = "/aliases"; __o…

HI to all, excuse me but this is my first msg. I have a OPI3 board and I try different OS (Arabian, Ubuntu, Debian) all in different release but I do not have wifi and lan. for wifi I have already try with copy firmware file but is is the same for lan I have in dmesg eth0. UP and DOWN. In my experience I have found only Ubuntu Xenial 4.9.118 on the Orange.org web site with wifi OK. can you help me? Thanks

/var/log/Xorg.0.log: [ 59.326] (EE) AIGLX error: sun4i-drm does not export required DRI extension [ 59.550] (II) IGLX: Loaded and initialized swrast [ 59.550] (II) GLX: Initialized DRISWRAST GL provider for screen 0 [ 59.550] (II) Initializing extension XFree86-VidModeExtension [ 59.551] (II) Initializing extension XFree86-DGA [ 59.553] (II) Initializing extension XFree86-DRI [ 59.553] (II) Initializing extension DRI2 [ 59.564] (II) modeset(0): Damage tracking initialized [ 59.565] (II) modeset(0): Setting screen physical size to 508 x 285 [ 60.561] (II) config/udev: Adding input device sunxi-ir (/dev/input/event1) [ 60.561] (**) sunxi-ir…

Good morning, I am using a version compiled with your script for Banana Pi M2 Berry to build a network HiFi streamer, and I am satisfied with it. I have installed LMS and Squeezelite, and everything is working great. Now I would like to add an Innomaker HAT AMP that has a 12V power connector that powers the Raspberry Pi at 5V via GPIO. The GPIO of the Banana Pi M2 Berry is declared compatible with the Raspberry Pi3, but I would like to be sure before frying the board in case it is not. Can you please confirm the total compatibility of the GPIO connector of the Banana Pi with that of the Raspberry Pi? Thank you for your response.

I have an OrangePI h3, I upload the Armbian in the SD card, but independent if the SD card is in or not, the Orange pi always display the both network leds turned on. Therefore I do not know if my problem is related to the SO or any hardware problem.

Hi, i need to download version Armbian 21.05.6 Buster with Linux 5.10.43-sunxi , is it possible to do it now and how? thank you

Maybe there has been a glitch in the update release process? I performed a sudo apt update && sudo apt upgrade and this has pulled down an automated build. Should it had pulled down a supported build instead?

sudo systemctl status bluetooth ● bluetooth.service - Bluetooth service Loaded: loaded (/lib/systemd/system/bluetooth.service; enabled; vendor preset: enabled) Active: active (running) since Sat 2023-02-25 16:50:52 IST; 1h 41min ago Docs: man:bluetoothd(8) Main PID: 1131 (bluetoothd) Status: "Running" Tasks: 1 (limit: 2209) Memory: 1.3M CPU: 402ms CGroup: /system.slice/bluetooth.service └─1131 /usr/lib/bluetooth/bluetoothd Feb 25 16:50:51 orange systemd[1]: Starting Bluetooth service... Feb 25 16:50:52 orange bluetoothd[1131]: Bluetooth daemon 5.64 Feb 25 16:50:52 orange systemd[1]: Started Bluetooth service. …

Hi, Firstly I wanted to say thanks for providing builds for the Cubietruck, however unsupported they are. Current build is working after I fixed up the repository and the wired network configuration - learnt a fair amount in one afternoon! Secondly, is it possible using armbian-config to switch to stable repository and a stable kernel and reasonably expect it to still work? Many thanks,

Hi All, I am trying to enable HID gadget on Banana Pi M2 Zero with latest Armbian OS for it. I followed the instructions in following link,but no luck: Switch USB port from OTG to HOST mode I get modprobe: ERROR: could not insert 'g_hid': No such device when I enter modprobe g_hid. I appreciate any help. Thanks

Hello, it is been awhile since I used armbian with Orange PI, now I took one orange PI NEO on it's connector is UART0, UART1 and UART2. My goal is to use all UARTS available on board. Googling a little I found the part where I should use BIX2FEX to convert script.bin and insert port definitions there, bot looks like that way is obsolete. looks by default only one uart is initialized: root@nanopineo:/boot# cat /proc/tty/driver/serial serinfo:1.0 driver revision: 0: uart:16550A mmio:0x01C28000 irq:49 tx:11630 rx:0 RTS|DTR 1: uart:unknown port:00000000 irq:0 2: uart:unknown port:00000000 irq:0 3: uart:unknown port:00000000 irq:0 4: uart:unknow…

Hi, This will be my first time using Armbian and OrangePi, sorry if theres stupid questions. I want to write a C++ application that uses LVGL to display information on a USB screen and have a few questions. 1) Will I be able to this screen in this setup. It uses the frame buffer (/dev/fb0). There are instructions for RaspberryPi, where its just plugged in and the frame buffer is available to use. 2) If I just use the latest Armbian Ubuntu version for this board what is the newest version of C++ I can use? (C++11/14/17 etc) 3) Is there a tool chain available to be able to cross compile my application (specifically from…

Thought this might help other people, so I wanted to share: https://github.com/robbieh/Inky7-BananaPi

Hello, I'm using the Lime2 with 22.11(Desktop) + latest Kernel & it works like a charm. I'm currently toying around with the Mia E-Ink Display (Onyx Boox) and the display goes blank during loading the Kernel. Could the problem be that the refresh rate is not supported? The specs of the display are 2200x1650 with an refresh rate of 38 Hertz. I tried to change that via armbian-config (boot section) but it made no difference. Does anybody know a way to make it work? best

Hello, Is there a guide / tutorial on making Kodi run with hardware acceleration enabled on Armbian on Orange PI PC Plus? e.g. like how LibreELEC does it. I have found a bunch of information on different sites and forums, but I can't put it all together. What I know so far: * Apparently the HW-accelerated decoding is supposed to be done on Kodi's side via VDPAU API * The Kodi build in Armbian repos does not have built-in support for libvdpau (?) * ffmpeg, the video decoding library used by Kodi, doesn't support Allwinner GPU out of the box and needs patching * Kodi needs to be re-compiled with the patched ffmpeg vers…

Hi, i am beginner in SBC other than Rapsberry Pi and i just got my NanoPi R1 with case. I try power the board without SD card for the first time and i see that friendlyWRT already installed but i would like to use a general OS. Since i can't download the official OS from friendlyelec, i saw that armbian is another way and might be better. I follow all step in quick start guide page, and can't even get my board boot up. Below is the list of OS that i try with SD card: - Armbian_22.11.1_Nanopi-r1_jammy_current_5.15.80_minimal - Armbian_22.11.1_Nanopi-r1_bullseye_current_5.15.80 - Armbian_22.11.1_Nanopi-r1_bullseye_current_5.15.8…

I try to use last images: Armbian_22.11.1_Nanopi-r1_bullseye_current_5.15.80.img.xz Armbian_22.11.1_Nanopi-r1_bullseye_current_5.15.80_minimal.img.xz But in both instances DHCP client couldn`t start. If I use old image: Armbian_22.08.1_Nanopi-r1_bullseye_current_5.15.63.img.xz All work correctly, nanopi get IP from DHCP server and I can connecting to it. What reason?

Hi. I'm trying to use GPIO's of OrangePi PC+ and after install WiringOP, when I run the gpio readall, all my GPIO's Mode are showing OFF. I tryed enable in armbian-config, but I have only pps-gpio and w1-gpio, I tryed enable both but doesn't work too. Someone knows some solution? Thanks.

Hi everyone, I connected my board with my PC via serial USB. Then I opened a serial with minicom and tried to test it out. I can send the strings from my board to PC without any problems but when I write something on the PC it sends garbage to my board. But, if I connect the TX, RX like: TX->TX RX->RX instead of TX->RX, RX->TX it sends normal from the PC and garbage from the board. I checked my baud rates but everything seems legit. I tried both 9600, 115200 bit rates, I also tried the both voltages (5V, 3.3V) What do you think could cause this problem? I saw this thread but seems like ther…

Dear community, I am experimenting with MangoPi board, trying to communicate with the CC2530 Zigbee board . To do so, I need an available UART port, the UART0 (/dev/ttyS0, pins 8 and 10) seems to be occupied by the console, but there should be two other UARTs according to the schematic. Some info: pi@nezha:~$ uname -a Linux nezha 5.19.0-rc1-d1 #trunk Fri Jul 22 12:44:22 MSK 2022 riscv64 riscv64 riscv64 GNU/Linux pi@nezha:~$ setserial -g /dev/ttyS* /dev/ttyS0: Permission denied /dev/ttyS2, UART: unknown, Port: 0x0000, IRQ: 0 /dev/ttyS3, UART: unknown, Port: 0x0000, IRQ: 0 /dev/ttyS4, UART: unknown, Port: 0x0000, IRQ: 0 /dev/ttyS5, UART: …

Bpi M2 Zero Armbian 23.02.0 sid can't change volume alsamixer said: This sound device does not have any controls. How can I fix this issue ?

Hi all, I am new to armbian, it is a wonderful project. I just have a nanopi neo core board, fellow the guide doc, it can be boot from the SD card, but the board has internal 8GB emmc. how can I install the armbian into it, so it can boot from emmc without using SD card? Thanks!

Hello. I have several new NanoPi-NEO Core devices. OS FriendlyELEC (Ubuntu 16.04.2) was already installed on them, and it does not allow me to boot from the SD card. There is an image created by a script emmc-backup.sh How do I deploy this image?

I had success with @ubobrov's sunxi-cedar-mainline driver before on H3 devices. I'm trying to get it to work on the Orange Pi 3 LTS (H6) however it keeps giving the following error: sunxi-cedar 1c0e000.video-engine: syscon failed... Any help would be much appreciated. dmesg: [ 6.167614] cedar_ve: loading out-of-tree module taints kernel. [ 6.167700] cedar_ve: module verification failed: signature and/or required key missing - tainting kernel [ 6.168445] sunxi cedar version 0.1 [ 6.168601] [cedar]: install start!!! [ 6.168654] cedar_ve: cedar-ve the get irq is 23 [ 6.168673] sunxi-cedar 1c0e000.video-engine: assign…

Hello. Somehow TX on UART 3 is not working. I connected USB-UART converter or the Banana Pi Zero M2 UART 3 Pins (as it shown here https://bananapi.gitbook.io/bpi-m2/en/bpi-m2_gpio_pin_define), set Baud rate, but I can't send anything from the SBC to PC. But I can send messages from PC to Banana pi. The converter is working properly(tested on Arduino). Do you have any ideas why? Physically nothing looks damaged, wires are soldered accurately and correctly.... Some system info $ uname -r 6.1.2-sunxi $ cat /etc/os-release PRETTY_NAME="Armbian 23.02.0-trunk Jammy" NAME="Ubuntu" VERSION_ID="22.04" VERSION="22.04.1 LTS (Jammy Jellyfish)" VERSION_CODENAME=jammy …

After installing the Bullseye version in the Orange PI3, I launched the Kodi installation. The videos however are in slow motion, with the audio at normal speed. Are there any codecs missing? The video driver? Thanks

Hi! I ended up here: My Banana M1 was working well, connecting to a monitor I was able to see it working. But after I removed the sd card (after turning the M1 off) and inserted into a Windows machine (it couldn't read the linux fs, did not format it) it won't start anymore. Tried with all the recommanded SD card software to test with the slowest method possible to detect errors on it, but no error on the sd card. Tried many times to write with the recommanded balena etcher the currently supported images on the sd card, like: Armbian_22.11.1_Bananapi_bullseye_current_5.15.80.img.xz Armbian_22.11.1_Bananapi_bullseye_current_5.15.80_minimal.img.xz Did check their…

Hello armbianers ! Armbian 22.11.1 Bullseye with Linux 5.15.80-sunxi on a banana pi m1 I've connected a lipo battery to my bpi m1, and now when I try to shutdown -h 0, it ends up in a kernel panic and instead of shutting down it remains powered up. Is there anything I can do to fix that? I'd know how to shut it down talking to the axp209 via i2c, but I'm not sure how/where to put that, or if that would be or not the proper way to go. Thanks, George.

Hello, I am using a NanoPi Duo2 with Armbian 22.11 and Kernel 5,15,80. This device uses an AP6216 wireless interface, which I have noticed are pretty common on sunxi based boards. I ran some bandwidth tests and had pretty poor results: [ ID] Interval Transfer Bandwidth [ 3] 0.0000-1.0000 sec 129 KBytes 1.05 Mbits/sec [ 3] 1.0000-2.0000 sec 129 KBytes 1.05 Mbits/sec [ 3] 2.0000-3.0000 sec 127 KBytes 1.04 Mbits/sec [ 3] 3.0000-4.0000 sec 129 KBytes 1.05 Mbits/sec [ 3] 4.0000-5.0000 sec 129 KBytes 1.05 Mbits/sec [ 3] 5.0000-6.0000 sec 127 KBytes 1.04 Mbits/sec [ 3] 6.0000-7.0000 sec 129 KBytes 1.05 Mbits/sec [ 3] 7…

Hi. After 2 years uptime it disconnected from wifi and was unable to reconnect even after reboot. I suspect my AC adapter has degraded. Can this SBC measure the voltage? Upd: saw this post: https://raspberrypi.stackexchange.com/questions/112122/wifi-not-connecting-depending-on-power-supply I use NetworkManager and when it starts it usually cannot connect to wifi saying that the pre-shared key is wrong, marking the connection as failed and not re-trying. In particular, the log contained a failed "asking for new key" message. Re-starting the service or manually activating the connection worked. As a workaround I created a *.conf file in …

I have enabled RDP option in armbian-config. It worked before but when I connect and enter my password, after pressing OK on the login screen the rdp tab just closes https://prnt.sc/WQKXky75i28c Can anyone help me? Logs: Jan 12 16:12:40 OrPi systemd[1]: Starting xrdp daemon... Jan 12 16:12:40 OrPi xrdp[4025]: [INFO ] address [0.0.0.0] port [3389] mode 1 Jan 12 16:12:40 OrPi xrdp[4025]: [INFO ] listening to port 3389 on 0.0.0.0 Jan 12 16:12:40 OrPi xrdp[4025]: [INFO ] xrdp_listen_pp done Jan 12 16:12:40 OrPi systemd[1]: xrdp.service: Can't open PID file /run/xrdp/xrdp.pid (yet?) after start: Operation not permitted Jan 12 16:12…

Hi Everyone, Is there anything additional required to enable better performance improvements (kernel patch for TXTS and RXTS are set to 3 each see below link) on a Banana PI running Armbian V21 / V22 ? I have updated the bootloader, and OS, and the performance is still abysmally poor. Mechanical or SSD drive connected to on board SATA yields a whopping 2.7-10 MB/sec write speed using dd with a large block size, or with the iozone tool ~5 upto ~45 for larger block sizes. Still a very far cry from the ~120 after the kernel patch applied in ~2019 => https://forum.armbian.com/topic/10352-a20-sata-write-speed-improvement/ …

Someone has any experience changing the A20 to A20-H, our provider offers to us this new version, but I'm afraid to be software incompatible.

My Opi3 has been running armbian for over 2 years (edge kernels & usually fully up-to-date). I have been using eMMC & I noticed an apparent slowdown about 6 months ago. As it performs cron-based tasks and is a stats collector, this performance was not noticable but doing a manual BIG dist-upgrade, it seems to take forever (20 minutes to do what should be under 5 minutes). If I run "mmc extcsd read /dev/mmcblk1", the results tell me that the eMMC is at least 90% used whatever that really means. Is this a sign of imminent failure ? hdparm shows read results of 17 MB/s which is actually slower than my alternative SD card boot device and nearly 1/10th …

I have a solar application for PC, so my goal is to reduce the power consumption in idle as much as possible. How would one go about this with the latest armbian distros?

I had build armbian 3 days ago, kernel ="5.8.13", with NanopiNEO, I want use a TFT screen, type is ILI9341, when I use "armbian-config" open spi_spidev, no /dev/spi* created, and screen does not work. here is config: # # cat /etc/modprobe.d/fbtft.conf options fbtft options fb_ili9341 name=fb_ili9341 gpios=rest:0,cs:67,dc:2,led:3 speed=48000000 fps=26 rotate=90 bgr=1 txbuflen=65536 debug=3 here is armbian-hardware-monitor.log Other: ttyS0 can't login, Does somebody can help me, thinks very much! armbian-hardware-monitor.log

Good afternoon. The problem is indicated in the title. The computer is connected to my monitor via HDMI and the screen resolution is only 1024x768. Which is inconvenient to use. I saw a similar topic raised on the official forum of a single-payer in 2019, but no one answered there. Is this a problem of the computer itself or the Linux kernel or drivers?

Hello and Happy New Year, From https://redirect.armbian.com/orangepi-r1/Bullseye_current I downloaded: Armbian_22.11.1_Orangepi-r1_bullseye_current_5.15.80.img.xz and installed. I see a file that shouldn't exist: $ ls -l /*core -rw-r--r-- 1 root root 16789504 Nov 30 11:55 /qemu_fstype_20221130-195503_13162.core A short while later I found this: $ armbian-add-overlay /etc/keys-h3.dts /usr/sbin/armbian-add-overlay: line 62: /lib/modules/5.15.80-sunxi/build/scripts/dtc/dtc: cannot execute binary file: Exec format error Error: dtc does not support compiling overlays There is a symlink involved: $ ls -l /lib/mo…